` REVISIONS
LTR DESCRIPTION DATE APPROVED
A Added suffix to PIN for mounting hole options.
Editorial changes throughout. 22 MAY 1991 Randy Larson
B Changes in accordance with NOR 5998-R001-01 21 DEC 2000 Allan Barone
C Section 2 updated to remove cancelled
documents and add the superseding
replacements. Corrected figure 1. Editorial
changes throughout.
23 DEC 2003 Thomas M. Hess
Prepared in accordance with ASME Y14.100 Selected item drawing
REV
PAGE
REV STATUS REV C C C C C C C C C C C C C C
OF PAGES PAGES 1 2 3 4 5 6 7 8 9 10 11 12 13 14
PMIC N/A PREPARED BY
Ken R. Beymer
DESIGN ACTIVITY
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OH 45444-5000
http://www.dscc.dla.mil
Original date of drawing
20 September 1989 CHECKED BY
David J. Corbett
APPROVED BY
Randy Larson
TITLE:
HOLDER, ELECTRICAL CARD, WEDGE
RETAINER, 5-PIECE, .250 INCH BY .260 INCH
BODY SIZE
SIZE
A CODE IDENT. NO.
14933 DWG NO. 89024
REV C PAGE 1 OF 14
AMSC N/A 5998-E047
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
DEFENSE LOGISTICS AGENCY
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 2
1. SCOPE
1.1 Scope. This drawing describes the requirements for a family of metal 5 wedge electrical card holders (hereafter referred to as
card retainers) intended to hold circuit card assemblies or printed wiring assemblies in their installed positions. Card retainers are
available with and without a visual lock indicator.
1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example:
89024
│
│
│
───┴───
Drawing
number
—20
│
│
│
─────┴─────
Dash number
(see table I)
C
│
│
│
───┴───
Finish
(B or C, see 3.3)
H
│
│
│
─────┴─────
Mounting holes
(H or T, see 3.1.1)
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are specified in sections 3, 4, or 5 of this specification. This section does not
include documents cited in other sections of this specification or recommended for additional information or as examples. While every
effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified
requirements of documents cited in sections 3, 4, or 5 of this specification, whether or not they are listed.
2.2 Government documents. The following specifications, standards, and handbooks form a part of this document to the extent
specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-C-5541 - Chemical Conversion Coatings on Aluminum and Aluminum Alloys.
MIL-A-8625 - Anodic Coatings for Aluminum and Aluminum Alloys.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-1285 - Marking of Electrical and Electronic Parts.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the
Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless
otherwise specified, the issues of the documents are those cited in the solicitation or contract.
AEROSPACE INDUSTRIES ASSOCIATION (AIA)
AIA/NAS NAS 1352 – Screw, Cap, Socket Head Undrilled and Drilled, Plain and Self-Locking, Alloy Steel, and
Corrosion-Resistant Steel and Heat-Resis tant Steel, UNRC-3A and UNRC-2A.
AIA/NAS NASM35338 – Washer, Lock-Spring, Helical, Regular (Medium) Series.
AIA/NAS NASM39086 – Pin, Spring-Tubular, Coiled, Heavy Duty.
(Application for copies should be addressed to the Aerospace Industries Association, 1250 Eye Street, NW, Suite 1200,
Washington, DC 20005-3924 or at URL: http://www.aia-aerospace.org).
ASTM INTERNATIONAL
ASTM A240 - Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for
Pressure Vessels and for General Applications.
ASTM A313 - Standard Specification for Stainless Steel Spring Wire.
ASTM A582 - Standard Specification for Free-Machining Stainless Steel Bars.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 3
ASTM A666 - Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat
Bar.
ASTM A967 - Standard Specification for Chemical Passivation Treatments for Stainless Steel Parts.
ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.
(Application for copies should be addressed to the ASTM International, PO Box C700, 100 Barr Harbor Drive, W est Coshohocken,
PA 19428-2959 or at URL http://www.astm.org).
SAE INTERNATIONAL (SAE)
SAE–AMS–QQ–A–200/8 - Aluminum Alloy 6061, Bar, Rod, Shapes, Tube, and Wire Extruded UNS A96061.
(Application for copies should be addressed to SAE World Headquarters, 400 Commonwealth Drive, Warrendale, PA 15096-0001
or at URL: http://www.sae.org)
(Non-Government standards and other publications are normally available from the organizations which prepare or which distribute
the documents. These documents also may be available in or through libraries or other informational services. They are also
distributed among technical groups and using Federal agencies.)
2.4 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this
document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
3. REQUIREMENTS
3.1 Interface and physical dimensions. See figures 1, 2, 3, 4 and table I.
3.1.1 Mounting holes. Card retainers are available with three mounting hole options. The options are countersunk holes or two
styles of tapped holes. Countersunk holes shall be .068/.073 inch (1.73/1.85 mm) diameter countersunk 100 degrees by .060 inch
(1.52 mm) deep. Card retainers with countersunk holes shall include a suffix "H" in the PIN. Card retainers with 2-56 UNF tapped
through holes shall include a suffix "T" in the PIN. Card retainers with 0-80 UNF tapped through holes shall include a suffix "S" in the
PIN (see figure 1, table I, and 1.2).
3.1.2 Optional visual lock. An option for visual lock indicator is available with dash numbers 11 through 20 (see configuration B on
figures 2 and 3).
3.2 Material.
3.2.1 Bodies, wedges, and shaft. The bodies (center and outer), wedges, and shaft material shall be aluminum alloy in accordance
with SAE–AMS–QQ–A–200/8, type 6061–T6 or ASTM B221.
3.2.2 Bushing and cup (visual lock indicating card holder only). The bushing material shall be stainless steel in accordance with
ASTM A582, type 303, 303SE, or 303SU. The cup material shall be stainless steel in accordance with ASTM A666, type 304 or 316.
3.2.3 Flat washer. The flat washer shall be stainless steel in accordance with ASTM A240.
3.2.4 Lockwasher. The lockwasher material shall be in accordance with NAS MS35338-135.
3.2.5 Roll pin. The roll pin material shall be in accordance with NAS MS39086–125.
3.2.6 Screw. The screw material shall be stainless steel. For card retainers without visual lock indication, the screw shall be type
NAS1352C04–10, 4-40 socket head cap screw. For visual lock indicating card retainers, the screw shall be type NAS1352C04–12,
4-40 socket head cap with red band on the head.
3.2.7 Spring (visual lock indicating card holder only). The spring material shall be stainless steel in accordance with ASTM A313.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 4
3.3 Finish.
3.3.1 Bodies, wedges, and shaft. The bodies, wedges, and shaft finish shall be chemical film in accordance with MIL-C-5541, class
3 or black anodize in accordance with MIL-A-8625, type I or II, class 2. Card retainers with a chemical film finish shall include a suffix
“C” in the PIN. Card retainers with black anodize finish shall include a suffix “B” in the PIN (see 1.2).
3.3.2 Bushing, cup and spring (visual lock indicating card holder only). The bushing, cup, and spring finish shall be passivate in
accordance with ASTM A967 or equivalent.
3.3.3 Flat washer, lockwasher, and screw. The flat washer, lockwasher, and screw shall be passivate in accordance with ASTM
A967 or equivalent.
3.3.4 Roll pin. The roll pin finish shall be in accordance with NASMS39086-125.
TABLE I. Card holder dimensions and configurations. 1/
Dimension L
± .02 (0.5 mm) Dimension A 3/
± .02 (0.5 mm) Dimension B 3/
± .005 (0.13 mm) Dimension C
± .02 (0.5 mm) Parts & configuration
Dash
number
2/ Inches mm Inches mm Inches mm Inches mm Figure 1 Figure 2
-01** 2.80 71.1 2.50 63.5 0.900 22.88 0.77 19.6 A A
-02** 3.00 76.2 2.70 68.6 1.100 27.94 0.84 21.3 A A
-03** 3.50 88.9 3.20 81.3 1.600 40.64 1.01 25.7 A A
-04** 3.80 96.5 3.50 88.9 1.900 48.26 1.11 28.2 A A
-05** 4.00 101.6 3.70 94.0 2.100 53.34 1.17 29.7 A A
-06** 4.50 114.3 4.20 106.7 2.600 66.04 1.34 34.0 A A
-07** 4.80 121.9 4.50 114.3 2.900 73.66 1.44 36.6 A A
-08** 5.00 127.0 4.70 119.4 3.100 78.74 1.51 38.4 A A
-09** 5.50 139.7 5.20 132.1 3.600 91.44 1.67 42.4 A A
-10** 5.80 147.3 5.50 139.7 3.900 99.06 1.77 45.0 A A
-11** 2.80 71.1 2.50 63.6 0.900 22.88 0.77 19.6 A and B B
-12** 3.00 76.2 2.70 68.6 1.100 27.94 0.84 21.3 A and B B
-13** 3.50 88.9 3.20 81.3 1.600 40.64 1.01 25.7 A and B B
-14** 3.80 96.5 3.50 88.9 1.900 48.26 1.11 28.2 A and B B
-15** 4.00 101.6 3.70 94.0 2.100 53.34 1.17 29.7 A and B B
-16** 4.50 114.3 4.20 106.7 2.600 66.04 1.34 34.0 A and B B
-17** 4.80 121.9 4.50 114.3 2.900 73.66 1.44 36.6 A and B B
-18** 5.00 127.0 4.70 119.4 3.100 78.74 1.51 38.4 A and B B
-19** 5.50 139.7 5.20 132.1 3.600 91.44 1.67 42.4 A and B B
-20** 5.80 147.3 5.50 139.7 3.900 99.06 1.77 45.0 A and B B
NOTES:
1/ Dimensions are in inches. Metric equivalents are given for general information only.
2/ Asterisk represent options for mounting holes (see 3.1.1) and finish (see 3.3).
3/ Dimension A is equal to dimension L minus .30 inch (7.6 mm). Dimension B is equal to dimension A minus 1.60 inch
(40.6 mm).
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 5
3.4 DSCC certificate of compliance. A certificate of compliance shall be submitted to DSCC-VAC by each manufacturer desiring to
be listed as a suggested source of supply (see 6.7). The certificate shall state that the manufacturer's product meets all the
requirements of this drawing.
3.4.1 Optional statement of compliance in lieu of testing. The acquiring activity, at its discretion, may accept from the manufacturer
a statement of compliance in lieu of the manufacturer performing the inspection of product for delivery tests (see 4.1.2 and 6.2.c).
3.5 Marking. Marking of the card holder is not required; however, each unit package shall be marked in accordance with
MIL-STD-1285 and include the PIN as specified herein (see 1.2), the manufacturer’s name or Commercial and Government Entity
(CAGE) code, and date lot codes.
3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable materials
should be used to the maximum extent possible provided that the material meets or exceeds the operational and maintenance
requirements, and promotes economically advantageous life cycle costs.
3.7 Workmanship. Card retainers shall be free from surface and finish flaws that affect life or serviceability. Card retainers shall be
finished smooth and shall have rounded edges with no evidence of chipping, cracking, deterioration, disintegration, or burrs.
Inches mm Inches mm Inches mm Inches mm
.030
.094 0.76
2.39 .108
.112 2.74
2.84 .178
.183 4.52
4.65 .625
.750 15.88
19.05
Configuration A and B parts
FIGURE 1. Card holder parts, interface and physical dimensions.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 6
Inches mm Inches mm Inches mm Inches mm
.005
.010
.02
.094
0.13
0.26
0.5
2.39
.105
.128
.160
.187
2.67
3.25
4.06
4.75
.204
.215
.250
.260
5.18
5.46
6.35
6.6
.50
.54
.76
.80
12.7
13.7
19.3
20.3
Configuration A and B parts
FIGURE 1. Card holder parts, interface and physical dimensions – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 7
Configuration A and B parts
Inches mm Inches mm Inches mm
.02
.048 0.5
1.22 .115
.12 2.92
3.0 .250
.260 6.35
6.60
FIGURE 1. Card holder parts, interface and physical dimensions – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 8
Configuration B only parts
Inches mm Inches mm Inches Mm Inches mm Inches mm
.005
.010
.016
0.13
0.25
0.41
.02
.025
.08
0.5
0.64
2.0
.090
.112
.145
2.29
2.85
3.68
.150
.187
.195
3.81
4.75
4.95
.21
.227
.230
5.3
5.77
5.84
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, tolerances are for ± .02 inch (0.5 mm) for two place
decimals and ± .010 (0.25 mm) for three place decimals.
4. See table I for L, A, B, and M dimensions and tolerances.
FIGURE 1. Card holder parts, interface and physical dimensions – Continued.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 9
FIGURE 2. Card holder assembly, interface and physical dimensions.
Inches mm Inches mm Inches mm Inches mm
.180 4.57 .227 5.77 .23 5.8 .35 8.9
FIGURE 3. Phys ical dimensions for visual lock.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 10
FIGURE 4. Card holder assembly expanded and relaxed dimensions.
4. VERIFICATION
4.1 Conformance inspections.
4.1.1 Inspection of product for delivery. Inspection of product for delivery shall consist of visual and mechanical inspections of
interface and physical dimensions (see 3.1), materials (see 3.2), finish (see 3.3), and workmanship (see 3.7). Criteria for defects are
listed in 4.1.5.
4.1.2 Optional statement of compliance. The acquiring activity, at its discretion, may accept a statement of compliance in lieu of the
manufacturer performing the inspection of product for delivery (see 6.2.c).
4.1.3 Sampling plan. A sample of parts shall be randomly selected in accordance with table II, normal sampling. If one or more
defects are found, the lot shall be rejected. Criteria for defects are listed in 4.1.5.
TABLE II. Sampling plan.
Lot size Normal Tightened
2 to 25 3 5
26 to 50 5 6
51 to 90 6 7
91 to 150 7 11
151 to 280 10 13
281 to 500 11 16
501 to 1,200 15 19
1,201 to 3,200 18 23
3,201 to 10,000 22 29
10,001 And
over 29 35
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 11
4.1.4 Rejected lots. If an inspection lot is rejected after normal sampling inspection, the manufacturer may rework it to correct the
defects, or screen out the defective parts, and resubmit for inspection. Resubmitted lots shall be inspected by selecting a random
sample of parts in accordance with table II, tightened sampling. If one or more defects are found in this sample, the lot shall be
rejected and shall not be supplied to this specification. Resubmitted lots which are acceptable shall be clearly identified as
reinspected lots.
4.1.5 Defective characteristics and properties. Dimensional characteristics are considered defective when out of tolerance.
Physical and functional properties are considered defective when outside the specified minimum, maximum, or range as applicable.
Workmanship characteristics are considered defective when they would be detrimental to the intended use, performance
requirements, or environmental survival of the part.
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2).
When actual packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to contact the
responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained by the Inventory Control
Point's packaging activity within the Military Service or Defense Agency, or within the Military Services system command. Packaging
data retrieval is available from the managing Military Service or Defense Agency's automated packaging files, CD-ROM products, or by
contacting the responsible packaging activity.
6. NOTES
6.1 Intended use. Devices conforming to this drawing are intended for use when military specifications do not exist and qualified
military devices that will perform the required function are not available for OEM application.
6.2 Ordering data. The contract or purchase order should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for delivery and one copy of the quality conformance inspection data or certificate of compliance that parts have
passed quality conformance inspection with each shipment of parts by the manufacturer.
c. Whether the manufacturer performs the product for delivery inspection (4.1.1) or provides an optional statement of compliance
(4.1.2).
d. Requirements for notification of change in product to the contracting activity, if applicable.
e. Requirements for packaging and packing.
6.3 Replaceability. Card retainers covered by this drawing will replace the commercial device covered by a contractor-prepared
specification or drawing.
6.4 Users of record. Coordination of this document for future revisions are coordinated only with the suggested sources of supply
and the users of record of this document. Requests to be added as a recorded user of this drawing should be in writing to DSCC-VAC.
6.5 Assistance. Questions or comments pertaining to this drawing should be addressed to Defense Supply Center Columbus ,
ATTN: DSCC/VAC, P.O. Box 3990, Columbus, OH 43216-5000; telephone (614) 692-0526; DSN 850-0526; facsimile (614) 693-1642;
or electronic mail “5998_Documents@dla.mil”. This document is available online at http://www.dscc.dla.mil/Programs/Milspec .
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 12
6.6 Supersession data. This drawing includes the essential requirements of previous revisions and supersedes previous PIN
designations (see 1.2).
Superseding DSCC drawing PIN
Superseded DSCC drawing
PIN per 89024 dated
20 September 1989
89024-01*H 89024-01*
89024-02*H 89024-02*
89024-03*H 89024-03*
89024-04*H 89024-04*
89024-05*H 89024-05*
89024-06*H 89024-06*
89024-07*H 89024-07*
89024-08*H 89024-08*
89024-09*H 89024-09*
89024-10*H 89024-10*
89024-11*H 89024-11*
89024-12*H 89024-12*
89024-13*H 89024-13*
89024-14*H 89024-14*
89024-15*H 89024-15*
89024-16*H 89024-16*
89024-17*H 89024-17*
89024-18*H 89024-18*
89024-19*H 89024-19*
89024-20*H 89024-20*
1/ Complete PIN will include an additional letter in place of the
asterisk to denote finish (either B or C, see 3.3.1).
6.7 Suggested sources of supply. Suggested sources of supply are listed herein. Additional sources will be added as they become
available. This table is not a qualified products list or an approved source list. This vendor has submitted a certificate of compliance to
DSCC; however, parts may be ordered from any manufacturer who agrees to supply items conforming to all the requirements of this
drawing.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 13
DSCC
drawing PIN
89024— 1/
Vendor similar
designation or type
number
DSCC
drawing PIN
89024— 1/
Vendor similar
designation or type
number
Vendor
CAGE Vendor name, address and
contact information
01CH
01BH
02CH
02BH
03CH
03BH
04CH
04BH
05CH
05BH
06CH
06BH
07CH
07BH
08CH
08BH
09CH
09BH
10CH
10BH
260-2.80H
A260-2.80H
260-3.00H
A260-3.00H
260-3.50H
A260-3.50H
260-3.80H
A260-3.80H
260-4.00H
A260-4.00H
260-4.50H
A260-4.50H
260-4.80H
A260-4.80H
260-5.00H
A260-5.00H
260-5.50H
A260-5.50H
260-5.80H
A260-5.80H
01CT
01BT
02CT
02BT
03CT
03BT
04CT
04BT
05CT
05BT
06CT
06BT
07CT
07BT
08CT
08BT
09CT
09BT
10CT
10BT
260-2.80T2
A260-2.80T2
260-3.00T2
A260-3.00T2
260-3.50T2
A260-3.50T2
260-3.80T2
A260-3.80T2
260-4.00T2
A260-4.00T2
260-4.50T2
A260-4.50T2
260-4.80T2
A260-4.80T2
260-5.00T2
A260-5.00T2
260-5.50T2
A260-5.50T2
260-5.80T2
A260-5.80T2
52094
Calmark Corporation
4915 Walnut Grove Ave
San Gabriel, CA 91776—2099
Tel: (626) 287—0451
Fax: (626) 287—7350
E-mail: sales@calmark.com
URL: www.c al mark.com
11CH
11BH
12CH
12BH
13CH
13BH
14CH
14BH
15CH
15BH
16CH
16BH
17CH
17BH
18CH
18BH
19CH
19BH
20CH
20BH
V260-2.80H
VA260-2.80H
V260-3.00H
VA260-3.00H
V260-3.50H
VA260-3.50H
V260-3.80H
VA260-3.80H
V260-4.00H
VA260-4.00H
V260-4.50H
VA260-4.50H
V260-4.80H
VA260-4.80H
V260-5.00H
VA260-5.00H
V260-5.50H
VA260-5.50H
V260-5.80H
VA260-5.80H
11CT
11BT
12CT
12BT
13CT
13BT
14CT
14BT
15CT
15BT
16CT
16BT
17CT
17BT
18CT
18BT
19CT
19BT
20CT
20BT
V260-2.80T2
VA260-2.80T2
V260-3.00T2
VA260-3.00T2
V260-3.50T2
VA260-3.50T2
V260-3.80T2
VA260-3.80T2
V260-4.00T2
VA260-4.00T2
V260-4.50T2
VA260-4.50T2
V260-4.80T2
VA260-4.80T2
V260-5.00T2
VA260-5.00T2
V260-5.50T2
VA260-5.50T2
V260-5.80T2
VA260-5.80T2
See note at end of table.
DEFENSE SUPPLY CENTER, COLUMBUS
COLUMBUS, OHIO
SIZE
A
CODE IDENT NO.
14933
DWG NO.
89024
REV C PAGE 14
DSCC
drawing PIN
89024— 1/
Vendor similar
designation or type
number
DSCC
drawing PIN
89024— 1/
Vendor similar
designation or type
number
Vendor
CAGE Vendor name, address and
contact information
01CS
01BS
02CS
02BS
03CS
03BS
04CS
04BS
05CS
05BS
06CS
06BS
07CS
07BS
08CS
08BS
09CS
09BS
10CS
10BS
260-2.80T0
A260-2.80T0
260-3.00T0
A260-3.00T0
260-3.50T0
A260-3.50T0
260-3.80T0
A260-3.80T0
260-4.00T0
A260-4.00T0
260-4.50T0
A260-4.50T0
260-4.80T0
A260-4.80T0
260-5.00T0
A260-5.00T0
260-5.50T0
A260-5.50T0
260-5.80T0
A260-5.80T0
52094
Calmark Corporation
4915 Walnut Grove Ave
San Gabriel, CA 91776—2099
Tel: (626) 287—0451
Fax: (626) 287—7350
E-mail: sales@calmark.com
URL: www.c al mark.com
11CS
11BS
12CS
12BS
13CS
13BS
14CS
14BS
15CS
15BS
16CS
16BS
17CS
17BS
18CS
18BS
19CS
19BS
20CS
20BS
V260-2.80T0
VA260-2.80T0
V260-3.00T0
VA260-3.00T0
V260-3.50T0
VA260-3.50T0
V260-3.80T0
VA260-3.80T0
V260-4.00T0
VA260-4.00T0
V260-4.50T0
VA260-4.50T0
V260-4.80T0
VA260-4.80T0
V260-5.00T0
VA260-5.00T0
V260-5.50T0
VA260-5.50T0
V260-5.80T0
VA260-5.80T0
1/ Parts must be purchased to this DSCC PIN to assure that all performance requirements and tests are met.
