SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B * VR(max) = 600V * IF(avg) = 5A * VF(typ) = 1.5V * DLCC3 Hermetic Ceramic Surface Mount Package Designed as a Drop In Replacement for "D-5B"/ "E-MELF" Package No Reverse Recovery No Forward Recovery High Reliability Screening Options Available * * * ABSOLUTE MAXIMUM RATINGS (TA = 25C unless otherwise stated) VRRM VRSM IF(AVG) IFSM PD Peak Repetitive Reverse Voltage Surge Peak Reverse Voltage Average Forward Current (1) Non-Repetitive Peak Forward Surge Current (3,4) Total Power Dissipation at TA = 25C Derate Above TA = 25C TJ Tstg Junction Temperature Range Storage Temperature Range 600V 600V 5A 60A 2.96 (2) 14.8mW/C (2) -55 to +225C -55 to +225C THERMAL PROPERTIES Symbols Parameters RJSP(IN) Thermal Resistance, Junction To Solder Pads TSP = 25C Max. Units 29 C/W RJA(PCB)(2) Thermal Resistance, Junction To Ambient, On PCB 67.5 C/W RJA(PCB) Thermal Resistance, Junction To Ambient, On PCB 123 C/W (3) Notes (1) IO1 is rated at 1.75A @ TA = 25C for PC boards where thermal resistance from mounting point to ambient is sufficiently controlled where TJ(Max) does not exceed 175C; This equates to RJA(PCB) 68C/W. (2) PCB = FR4, 0.0625 Inch (1.59mm) thick, single layer, 1.0-Oz Cu, Pad Size, (1.0" x 1.0"), (25.4mm x 25.4mm) , horizontal in still air. (3) PCB = FR4, 0.0625 Inch (1.59mm) thick, single layer, 1.0-Oz Cu, Pad Size, (0.070" x 0.155"), (1.78mm x 3.94mm) , horizontal in still air. IO1 is rated at 1.0A @ TA = 25C for PC boards where RJA(PCB) 125C/W. Derate at 7.33mA/C above TA = 25C in this case. (4) MIL-STD-750 Method 4066.4 Condition A1. IO = 1A, VRWM = 600V, VRSM = 600V, ten surges of 8.3mS each at 1 minute intervals, TA = 25C. Recommended solder pad layout dimensions for this device, as detailed within this datasheet for the D-5A device. Semelab ltd reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to verify that datasheets are current before placing an order. Semelab ltd Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 9166 Issue 2 Page 1 of 6 SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise stated) Symbol VF (1) IR Parameters Test Conditions Diode Forward Voltage Leakage Current Min. Typ. Max. IF = 5A TJ = 25C 1.5 1.8 IF = 5A TJ = 175C 2.0 2.4 VR = 600V TJ = 25C 50 200 VR = 600V TJ = 175C 100 1000 VR = 600V IF = 5A di/dt = 500A/s TJ = 25C VR = 0V TJ = 25C 550 VR = 200V TJ = 25C 65 VR = 400V TJ = 25C 50 Unit V A DYNAMIC CHARACTERISTICS QC Total Capacitive Charge CT Junction Capacitance (f = 1.0MHz) 28 nC pF Notes (1) Pulse Width 300us, 2% Semelab ltd Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 9166 Issue 2 Page 2 of 6 SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B Typical Performance Over Temperature Range The Forward Characteristics of 600V D3A Diodes 12.0 If - Forward Current (A) 10.0 8.0 6.0 4.0 2.0 0.0 0 0.5 1 -55 1.5 V f - For wa r125 d V ol t a ge ( V150 ) 100 25 2 175 2.5 225 Reverse Leakage characteristics of 600V D3A Diodes 18.0E-6 16.0E-6 Reverse Current (A) 14.0E-6 12.0E-6 10.0E-6 8.0E-6 6.0E-6 4.0E-6 2.0E-6 000.0E+0 0 100 200 300 400 500 600 700 800 V R R ev er s e V ol t age ( V ol t s) -55 Semelab ltd Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com 25 100 125 Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com 150 175 225 Document Number 9166 Issue 2 Page 3 of 6 SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B SiC Schottky Diode, no minority SML05SC06D3 carrier recombination thus zero reverse recovery. Recovery time Equivalent Reverse Recovery Time Device show n is due to a small junction IF=500mA, IR = 1A, IRR=250mA capacitance charge and is independent of junction temperature C u rre n t(A ) 1.000 0.500 0.000 -0.500 -1.000 -1 8 -1 6 -1 4 -1 2 -1 0 -8 -6 -4 -2 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 -1.500 Time (nS) -55C Semelab ltd Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com 0C 25C 50C 100C Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com 150C 200C 225C Document Number 9166 Issue 2 Page 4 of 6 SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B MECHANICAL DATA A DLCC3 Variant A (D3A) D PAD 1 PAD 2 B SML D3A C C 1 2 DIMENSION A B C D A D C C 1 2 mm 7.00 0.10 3.75 0.10 1.60 0.10 1.76 0.10 Inches 0.275 0.004 0.143 0.004 0.063 0.004 0.069 0.004 DLCC3 Variant B (D3B) PAD 1 PAD 2 PAD 3 B SML D3B ANODE CATHODE DIMENSION A B C D ANODE CATHODE LID CONTACT TO CATHODE* mm 7.00 0.10 3.75 0.10 1.60 0.10 1.76 0.10 Inches 0.275 0.004 0.143 0.004 0.063 0.004 0.069 0.004 3 * The additional contact provides a connection to the lid in the application. Connecting the metal lid to a known electrical potential stops deep dielectric discharge in space applications; see the Space Weather link www.semelab.co.uk/dlcc3.html on the Semelab web site. Package variant to be specified at order. The DLCC3 package design takes full advantage of the proven high reliability pedigree of the HTCC surface mount packaging technology, which is easily integrated for automated assembly. Semelab has taken the existing standards for ceramic surface mount package manufacture and added additional design features to enhance thermal performance, to present a competitive alternative for high reliability applications. SOLDER PAD LAYOUT C A B A B C mm 7.32 1.78 3.94 Inches 0.288 0.070 0.155 Soldering temperature should be 260C for a maximum of 10 seconds. The physical dimensions for the DLCC3 ceramic package are designed to be different from the published dimensions for the "D-5B" and "EMELF" outlines. The DLCC3 design fully utilises the recommended solder footprint for the "D-5B" / "E-MELF" Package, and as such presents a drop in replacement for existing board designs. PACKAGE MASS Gold Plated Solder Pad Finish = 150mg Semelab ltd Telephone +44 (0) 1455 556565 Email: sales@semelab-tt.com Coventry Road, Lutterworth, Leicestershire, LE17 4JB Fax +44 (0) 1455 552612 Website: http://www.semelab-tt.com Document Number 9166 Issue 2 Page 5 of 6 SiC SCHOTTKY DIODE SML05SC06D3A / SML05SC06D3B SCREENING OPTIONS ORDERING INFORMATION Space Level (JQRS/ESA) and High Reliability options are available in accordance with the High Reliability and Screening Options Handbook available for download from the from the TT electronics Semelab web site. Part numbers are built up from Type, Package Variant, and screening level. The part numbers are extended to include the additional options as shown below. ESA Quality Level Products are based on the testing procedures specified in the generic ESCC 5000 and in the corresponding part detail specifications. Type - See Electrical Stability Characteristics Table Package Variant - See Mechanical Data Screening Level - See Screening Options (ESA / JQRS) Additional Options: Semelab's QR216 and QR217 processing specifications (JQRS), in conjunction with the companies ISO 9001:2000 approval present a viable alternative to the American MILPRF-19500 space level processing. QR217 (Space Level Quality Conformance) is based on the quality conformance inspection requirements of MIL-PRF19500 groups A (table V), B (table VIa), C (table VII) and also ESA / ESCC 5000 (chart F4) lot validation tests. QR216 (Space Level Screening) is based on the screening requirements of MIL-PRF-19500 (table IV) and also ESA /ESCC 5000 (chart F3). JQRS parts are processed to the device data sheet and screened to QR216 with conformance testing to Q217 groups A and B in accordance with MIL-STD-750 methods and procedures. Additional conformance options are available, for example Pre-Cap Visual Inspection, Buy-Off Visit or Data Packs. These are chargeable and must be specified at the order stage (See Ordering Information). Minimum order quantities may apply. Alternative or additional customer specific conformance or screening requirements would be considered. Contact Semelab sales with enquires. MARKING DETAILS Parts can be laser marked with approximately 7 characters on two lines and always includes cathode identification. Typical marking would include part or specification number, week of seal or serial number subject to available space and legibility. Customer specific marking requirements can be arranged at the time of order. Example Marking: Customer Pre-Cap Visual Inspection Customer Buy-Off visit Data Pack Solderability Samples Scanning Electron Microscopy Radiography (X-ray) Total Dose Radiation Test .CVP .CVB .DA .SS .SEM .XRAY .RAD MIL-PRF-19500 (QR217) Group B charge Group B destructive mechanical samples Group C charge Group C destructive electrical samples Group C destructive mechanical samples .GRPB .GBDM (12 pieces) .GRPC .GCDE (12 pieces) .GCDM (6 pieces) ESA/ESCC Lot Validation Testing (subgroup 1) charge LVT1 destructive samples (environmental) LVT1 destructive samples (mechanical) Lot Validation Testing (subgroup 2) charge LVT2 endurance samples (electrical) Lot Validation Testing (subgroup 3) charge LVT3 destructive samples (mechanical) .LVT1 .L1DE (15 pieces) .L1DM (15 pieces) .LVT2 .L2D (15 pieces) .LVT3 .L3D (5 pieces) Additional Option Notes: 1) All `Additional Options' are chargeable and must be specified at order stage. 2) When Group B,C or LVT is required, additional electrical and mechanical destructive samples must be ordered 3) All destructive samples are marked the same as other production parts unless otherwise requested. Example ordering information: The following example is for the SML05SC06D3A / SML05SC06D3B part with package variant B, JQRS screening, additional Group C conformance testing and a Data pack. Part Numbers: SML05SC06D3B-JQRS (Include quantity for flight parts) SML05SC06D3B.GRPC (chargeable conformance option) SML05SC06D3B.GCDE (charge for destructive parts) SML05SC06D3B.GCDM (charge for destructive parts) SML05SC06D3B.DA (charge for Data pack) Customers with any specific requirements (e.g. marking or screening) may be supplied with a similar alternative part number (there is maximum 20 character limit to part numbers). Contact Semelab sales with enquiries. High Reliability and Screening Options Handbook link: http://www.semelab.co.uk/pdf/misc/documents/hirel_and_screening_options.pdf Semelab Limited Coventry Road, Lutterworth, Leicestershire, LE17 4JB Telephone +44 (0) 1455 556565 Fax +44 (0) 1455 552612 Email: sales@semelab-tt.com Website: http://www.semelab-tt.com Document Number 9166 Issue 2 Page 6 of 6