FW005G - FW10G
FAST RECOVERY GLASS
PASSIVATED BRIDGE RECTIFIERS
PRV : 50 - 1000 Volts
Io : 1.5 Amperes
FEATURES :
* Glass passivated chip
* High case dielectric strength
* High surge current capability
* High reliability
* Low reverse current
* Low forward voltage drop
* Fast switching for high efficiency
* Ideal for printed circuit board
MECHANICAL DATA :
* Case : Reliable low cost construction
utilizing molded plastic technique
* Epoxy : UL94V-O rate flame retardant
* Terminals : Plated leads solderable per
MIL-STD-202, Method 208 guaranteed
* Polarity : Polarity symbols marked on case
* Mounting position : Any
* Weight : 1.29 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Rating at 25
°
C ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
SYMBOL FW
005G
FW
01G
FW
02G
FW
04G
FW
06G
FW
08G
FW
10G UNIT
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts
Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts
Maximum DC Blocking Voltage VDC 50 100 200 400 600 800 1000 Volts
Maximum Average Forward Current
0.375" (9.5 mm) lead length Tc = 25°CIF(AV) 1.5 Amps.
Peak Forward Surge Current Single half sine wave
Superimposed on rated load (JEDEC Method) IFSM 30 Amps.
Rating for fusing ( t < 8.3 ms. ) I2t10 A2S
Maximum Forward Voltage per Diode at IF = 1.0 Amp. VF1.3 Volts
Maximum DC Reverse Current Ta = 25 °CIR10 µA
at Rated DC Blocking Voltage Ta = 100 °CIR(H) 1.0 mA
Maximum Reverse Recovery Time (Note 1) Trr 150 250 500 ns
Typical Junction Capacitance per Diode (Note 2) CJ24 pf
Typical Thermal Resistance (Note 3) RθJA 36 °C/W
Operating Junction Temperature Range TJ - 50 to + 150 °C
Storage Temperature Range TSTG - 50 to + 150 °C
Notes :
1 ) Measured with I
F
= 0.5 Amp., I
R
= 1 Amp., Irr = 0.25 Amp.
2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts.
3 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board mounting. UPDATE : APRIL 23,1998
RATING
WOB
-
0.39 (10.0)
0.31 (7.87)
0.034 (0.86)
0.028 (0.71)
AC
+
1.10 (27.9)
MIN.
0.22 (5.59)
0.18 (4.57)
0.22 (5.59)
0.18 (4.57)
0.22 (5.59)
0.18 (4.57)
+
-AC
AC
1.00 (25.4)
MIN.
Dimension in inches and (millimeter)
RATING AND CHARACTERISTIC CURVES ( FW005G - FW10G )
FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
+
NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm, 22 pF.
2. Rise time = 10 ns max., Source Impedance = 50 ohms.
3. All Resistors = Non-inductive Types.
FIG.2 - DERATING CURVE FOR OUTPUT FIG.3 - MAXIMUM NON-REPETITIVE PEAK
RECTIFIED CURRENT FORWARD SURGE CURRENT
0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100
CASE TEMPERATURE, ( °C) NUMBER OF CYCLES AT 60Hz
FIG.4 - TYPICAL FORWARD CHARACTERISTICS FIG.5 - TYPICAL REVERSE CHARACTERISTICS
0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2
FORWARD VOLTAGE, VOLTS
60 Hz, Resistive or Inductive load.
1.2
0.6
0.3
1.5
10 10
1.0
24
0
30
0
12
6
0.01
1
80
0.01
0.1
0.1
100 1400 20 40 60 120
PERCENT OF RATED REVERSE
VOLTAGE, (%)
PEAK FORWARD SURGE
CURRENT, AMPERES
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FORWARD CURRENT, AMPERES
REVERSE CURRENT, MICROAMPERES
TJ = 25 °C
Pulse Width = 300 µs
1 % Duty Cycle
SINGLE HALF SINE WAVE
(JEDEC METHOD)
TJ = 55 °C
TJ = 100 °C
TJ = 25 °C
18
0.9
0.375(9.5mm)
Copper Pads
0.22" x 0.22"
(5.5 x5.5mm)
PC Board
20
SET TIME BASE FOR 50/100 ns/cm
Trr
+ 0.5 A
0
- 0.25
- 1.0 A
1 cm
OSCILLOSCOPE
( NOTE 1 )
1 Ω
50 Ω10 Ω
D.U.T.
50 Vdc
(approx)
PULSE
GENERATOR
( NOTE 2 )
