SinglFuseTM SF-1206SP Series Features n Time lag thin film chip fuse for overcurrent protection n 3216 (EIA 1206) miniature footprint n Surface mount packaging for automated assembly n UL listed (UL 248-14) n RoHS compliant* and halogen free** SF-1206SP Series - Time Lag Surface Mount Fuses Electrical Characteristics SF-1206SP050 SF-1206SP080 SF-1206SP100 SF-1206SP125 SF-1206SP150 Rated Current (Amps) 0.50 0.80 1.00 1.25 1.50 SF-1206SP250 SF-1206SP300 SF-1206SP400 SF-1206SP500 2.50 3.00 4.00 5.00 Model SF-1206SP200 2.00 SF-1206SP700 Resistance (m) Typ.*** 738.5 215 163.5 100 68.5 Fusing Time Open within 1~120 sec. at 200 % rated current Rated Voltage Breaking Capacity DC 63 V DC 63 V 50 A 48.5 35 27 14 11 7.00 Typical I2t (A2s) **** 0.027 0.072 0.134 0.233 0.305 0.509 DC 32 V DC 32 V 50 A 7.5 0.777 1.285 2.374 5.510 10.170 *** Resistance value measured with less than 10 % of rated current. Resistance tolerance 25 %. ****Typical I2t value measured at 10x rated current. Reliability Testing No. Test Requirement Test Condition 1 Carrying Capacity No fusing 2 Fusing Time Within 120 seconds 200 % of its rated current 3 Interrupting Ability No mechanical damages After the fuse is interrupted, rated voltage applied for 30 seconds again 4 Bending Test No mechanical damages Distance between holding points: 90 mm, Bending: 3 mm,1 time, 30 seconds 5 Resistance to Solder Heat 20 % 260 C 5 C,10 seconds 1 second 6 Solderability 95 % coverage minimum 235 C 5 C, 2 0.5 second 245 C 5 C, 2 0.5 second (lead free) 7 Temperature Rise <75 C 100 % of its rated current, measure of surface temperature 8 Resistance to Dry Heat 20 % 105 C 5 C,1000 hours 9 Resistance to Solvent No evident damage on protective coating and marking 23 C 5 C of isopropyl alcohol, 90 seconds 10 Residual Resistance 10k ohms or more Measure DC resistance after fusing 11 Thermal Shock DR < 10 % -20 C / +25 C /+125 C /+25 C, 10 cycles Agency Recognition UL File Number................................................................ E198545 Rated current, 4 hours WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov Environmental Characteristics Operating Temperature........................................-20 C to +105 C Storage Conditions Temperature......................................................+5 C to +35 C Humidity................................................................40 % to 75 % Shelf Life................................ 2 years from manufacturing date Moisture Sensitivity Level..............................................................1 ESD Classification (HBM)...................................................Class 6 * RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. ** Bourns considers a product to be "halogen free" if (a) the Bromine (Br) content is 900 ppm or less; (b) the Chlorine (Cl) content is 900 ppm or less; and (c) the total Bromine (Br) and Chlorine (Cl) content is 1500 ppm or less. "SinglFuse" is a trademark of Bourns, Inc. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SinglFuseTM SF-1206SP Series Applications n Portable memory n Cell phones n LCD monitors n Rechargeable battery packs n Disk drives n Battery chargers n PDAs n Set top boxes n Digital cameras n Industrial controllers n DVDs SF-1206SP Series - Time Lag Surface Mount Fuses Typical Part Marking How to Order Represents total content. Layout may vary. SF - 1206 SP 050 - 2 SinglFuseTM Product Designator SMD Footprint 3216 (EIA 1206) size Fuse Blow Type SP = Time Lag RATED CURRENT (A) T = 2.50 F = 0.50 3 = 3.00 K = 0.80 W = 4.00 L = 1.00 Y = 5.00 M = 1.25 Z = 7.00 P = 1.50 S = 2.00 Rated Current 050-700 (500 mA - 7.00 A) Packaging Type - 2 = Tape & Reel (5,000 pcs./reel) Solder Reflow Recommendations Construction & Material Content OVERCOAT 250 Peak: 250 +0/-5 C Sn PLATING TEMPERATURE (C) 230 C or higher 200 PRE-HEATING ZONE 180 C FUSE ELEMENT CERAMIC SUBSTRATE 150 C 150 Cu / Ni PLATING 90 30 Seconds 100 Packaging Quantity 30 10 Seconds 5,000 pieces per 7-inch reel SOLDERING ZONE 50 HEATING TIME 3.1 0.1 (.122 .004) 2.2 0.2 .008) Recommended Pad (.087 Layout PEAK: 250 +0/-5 C, 5 seconds PRE-HEATING ZONE: 150 to 180 C, 90 30 seconds 3.1 0.1 SOLDERING ZONE: 230 C or higher, 30 10 seconds(.122 .004) Product Dimensions 0.5 0.3 (.020 .012) 3.1 0.1 (.122 .004) 0.5 0.3 (.020 .012) 1.55 0.1 (.061 .004) 0.5 0.3 (.020 .012) 0.5 0.3 (.020 .012) 0.6 0.1 (.024 .004) 0.5 0.3 (.020 .012) 2.2 0.2 (.087 .008) 1.55 0.1 (.061 .004) 1.65 0.15 4.7 0.3(.065 .006) (.185 .012) 1.55 0.1 0.5(.061 0.3 .004) (.020 .012)2.2 0.2 (.087 .008) 0.6 0.1 (.024 .004) 0.6 0.1 0.5 (.024 0.2 .004)0.5 0.2 (.020 .008) (.020 .008) 1.65 0.15 (.065 .006) 4.7 0.3 (.185 .012) 1.65 0.15 (.065 .006) 4.7 0.3 (.185 .012) 0.5 0.2 (.020 .008) 0.5 0.2 DIMENSIONS: (.020 .008) MM (INCHES) Specifications 0.5 aresubject to 0.5 change 0.2 0.2 without notice. Users should(.020 verify actual device performance in their specific applications. .008) (.020 .008) The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SF-1206SP Series - Time Lag Surface Mount Fuses Average Time Current Curves Minimum I2T V Clear Time Curves 2.00 A 2.50 A 3.00 A 3.50 A 4.00 A 5.00 A 6.00 A 1.60 A 1.50 A 1.25 A 1.00 A 0.80 A 0.63 A 0.50 A 100 100 2.00 A 1.60 A 1.50 A 1.25 A 1.00 A 0.80 A 10 JOULE INTEGRAL (A2 SEC) 10 CLEARING TIME (S) 6.00 A 5.00 A 4.00 A 3.15 A 3.00 A 2.50 A 1 0.1 0.63 A 0.50 A 1 0.1 0.01 0.01 0.001 0.1 1 10 100 CURRENT (A) 0.001 0.001 0.01 0.1 1 CLEARING TIME (S) PERCENT OF RATING (%) Thermal Derating Curve 120 110 100 REV. D 01/19 90 80 -20 0 20 40 60 80 100 120 AMBIENT TEMPERATURE (C) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. SF-1206SP Series Tape and Reel Specifications Tape Dimensions SF-1206SP Series per EIA 481-2 8.0 0.2 (.315 .008) W P 0 P1 P 2 4.0 0.1 (.157 .004) 4.0 0.1 (.157 .004) 2.0 0.05 (.079 .002) 2.0 0.15 (.079 .006) A 3.6 0.2 (.142 .008) B 3.5 0.05 (.138 .002) F 1.75 0.1 (.069 .004) E 1.5 + 0.1/-0 (.059 + .004/-0) D0 0.84 0.1 (.033 .004) T Reel Dimensions A 178 0.2 (7.087 .079) B Min. 60.0 1.0 (2.362 .039) C 13.0 1.0 (.512 .039) 9.0 1.0 (.354 .039) W 11.4 2.0 (.449 .079) T T DIMENSIONS: MM (INCHES) W BOTTOM TAPE A DIA. C DIA. DO PO E TOP TAPE B B DIA. PAPER TAPE RESISTOR TAPE T F A P1 W P2 DIRECTION OF UNREELING Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns(R) products manufactured by or on behalf of Bourns, Inc. and (32 ?+( 3$2".++$"3(5$+8:.41-2; Unless otherwise expressly indicated in writing, Bourns(R) products and data sheets relating thereto are subject to change 6(3'.43-.3("$2$122'.4+#"'$"*%.1 -#.!3 (-3'$+ 3$231$+$5 -3(-%.1, 3(.- -#5$1(%83' 324"'(-%.1, 3(.-(2"411$-3 and complete before placing orders for Bourns(R) products. The characteristics and parameters of a Bourns(R) product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on Bourns' knowledge of typical requirements in generic applications. The characteristics and parameters of a Bourns(R)/1.#4"3(- 42$1 //+(" 3(.-, 85 18 %1.,3'$# 3 2'$$3"' 1 "3$1(23("2 -#/ 1 ,$3$12#4$3.(3'$".,!(- 3(.-.%3'$.41-2(R) product with other components (-3'$42$1<2 //+(" 3(.-.1((3'$$-5(1.-,$-3.%3'$42$1 //+(" 3(.-(32$+%'$"' 1 "3$1(23("2 -#/ 1 ,$3$12.% .41-2(R) /1.#4"3 +2." - -##.5 18(-#(>$1$-3 //+(" 3(.-2 -# "34 +/$1%.1, -"$, 85 18.5$13(,$2$122'.4+# +6 825$1(%8 the actual performance of the Bourns(R)/1.#4"3(-3'$(12/$"(="#$5("$2 -# //+(" 3(.-2 -#, *$3'$(1.6-(-#$/$-#$-3 )4#&,$-321$& 1#(-&3'$ ,.4-3.% ##(3(.- +3$23, 1&(-3.#$2(&-(-3.3'$(1#$5("$.1 //+(" 3(.-3.".,/$-2 3$%.1 #(>$1$-"$2!$36$$-+ !.1 3.18 -#1$ +6.1+#".-#(3(.-2 -+$22.41-2' 2$7/+("(3+8#$2(&- 3$# -(-#(5(#4 +.41-2(R) product as meeting the requirements of a particular industry 23 -# 1#$& .1 / 13("4+ 104 +(=" 3(.-$&+(23$#.11$".&-(9$#.41-2(2-.31$2/.-2(!+$%.1 -8 % (+41$.% -(-#(5(#4 +.41-2(R)/1.#4"33.,$$33'$1$04(1$,$-32.%24"'(-#4231823 -# 1#.1/ 13("4+ 104 +(=" 3(.-2$12 of Bourns(R) products are responsible for ensuring compliance with safety-related requirements and standards applicable to 3'$(1#$5("$2.1 //+(" 3(.-2 Bourns(R)/1.#4"32 1$-.31$".,,$-#$# 43'.1(9$#.1(-3$-#$#%.142$(--4"+$ 1+(%$2 5(-&+(%$"1(3(" +.1+(%$2423 (-(-& //+(" 3(.-2-.1(- -8.3'$1 //+(" 3(.-26'$1$% (+41$.1, +%4-"3(.-, 81$24+3(-/$12.- +(-)418#$ 3'.12$5$1$/1./$138 .1$-5(1.-,$-3 +# , &$-+$22$7/1$22+8 -#2/$"(=" ++8 //1.5$#(-61(3(-&!836. 43'.1(9$#.41-21$/1$2$-3 3(5$2 on a case-by-case basis, use of any Bourns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ourns(R)23 -# 1#/1.#4"32 1$-.33$23$#3.".,/+86(3'-(3$#3 3$2$#$1 +5( 3(.-#,(-(231 3(.-23 -# 1#2&$-$1 ++8 .1 -8.3'$1&$-$1 ++8$04(5 +$-3&.5$1-,$-3 +.1& -(9 3(.-23 -# 1# //+(" !+$3./1.#4"32#$2(&-$#.1, -4% "341$#%.1 42$(- (1"1 %3.12/ "$ //+(" 3(.-2.41-2$7/1$22+8(#$-3(=$2.41-2(R) standard products that are suitable for use in aircraft .12/ "$ //+(" 3(.-2.-24"'/1.#4"32<# 3 2'$$32(-3'$2$"3(.-$-3(3+$#://+(" 3(.-2;-+$22$7/1$22+8 -#2/$"(=" ++8 //1.5$#(-61(3(-&!836. 43'.1(9$#.41-21$/1$2$-3 3(5$2.- " 2$!8" 2$! 2(242$.% -8.3'$1.41-2(R) standard /1.#4"3(- - (1"1 %3.12/ "$ //+(" 3(.-,(&'3-.3!$2 %$ -#3'42(2-.31$".,,$-#$# 43'.1(9$#.1(-3$-#$# -#(2 3 the user's sole risk. '$42$ -#+$5$+.%3$23(-& //+(" !+$3..41-2(R) custom products shall be negotiated on a case-by-case basis by Bourns and the user for which such Bourns(R)"423.,/1.#4"32 1$2/$"( ++8#$2(&-$#!2$-3 61(33$- &1$$,$-3!$36$$-.41-2 -#3'$42$11$& 1#(-&3'$42$ -#+$5$+.%24"'3$23(-&3'$ !.5$/1.5(2(.-2 //+(" !+$3..41-2(R) standard products shall also apply to such Bourns(R) custom products. Users shall not sell, transfer, export or re-export any Bourns(R)/1.#4"32.13$"'-.+.&8%.142$(- "3(5(3($26'("'(-5.+5$3'$ #$2(&-#$5$+./,$-3/1.#4"3(.-42$.123."*/(+(-&.%-4"+$ 1"'$,(" +.1!(.+.&(" +6$ /.-2.1,(22(+$2-.12' ++3'$842$ Bourns(R)/1.#4"32.13$"'-.+.&8(- -8% "(+(386'("'$-& &$2(- "3(5(3($21$+ 3(-&3.24"'#$5("$2'$%.1$&.(-&1$231("3(.-2 //+83. ++42$2 -# //+(" 3(.-23' 35(.+ 3$- 3(.- +.1(-3$1- 3(.- +/1.'(!(3(.-2(-"+4#(-&$,! 1&.2.1(-3$1- 3(.- + 1$&4+ 3(.-2413'$1.41-2(R) products and Bourns technology and technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes. Bourns(R) products may not, without /1(.1 43'.1(9 3(.-%1.,.41-2 -#.13'$.5$1-,$-3!$1$2.+#31 -2%$11$#.11$$7/.13$#3. -8/ 138-.3$+(&(!+$ 3.1$"$(5$".,,.#(3($22.%36 1$ -#3$"'-(" +# 3 .3'$, 7(,4,$73$-3/$1,(33$#!8 //+(" !+$+ 6.41-2#(2"+ (,2( -8 -# +++( !(+(38%.12/$"( +/4-(3(5$".-2$04$-3( + (-"(#$-3 +.1(-#(1$"3# , &$2.1+.231$5$-4$2.1+.23/1.=32 -#(( -8 -# ++(,/+($#6 11 -3($2(-"+4#(-&(,/+($#6 11 -3($2 .%=3-$22%.1/ 13("4+ 1/41/.2$-.-(-%1(-&$,$-3 -#,$1"' -3 !(+(38 bilingual versions are available at: Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf