ADVANCE INFORMATION Data SheetNo. PD60183 IR4007K Switched Mode Power Supply IC Descriptions Features The IR4007 is a dual mode voltage and current controller combined with a MOSFET in a single Package. The IR4007 is designed for use in AC/DC and DC/DC switching power supplies upto 100VDC nominal input. The device can operate in either a quasi-resonant or Pulse Ratio Control (PRC) mode, and thereby variable frequency operation. * Primary current mode control, and secondary voltage mode control * Vcc Over-voltage protection (latched) * Over-current & over-temperature protection * Quasi resonant, variable frequency operation * 5 pin TO262 package * 0.4 Rds(on) max/ 200V MOSFET * Fully Characterized Avalanche Energy Typical Connection Diagram Vin (AC/ DC) Vout (DC) 3 Drain Vcc 4 IR4007K FB Source 1 5 Gnd 2 *Please note that this datasheet contains advance information which could change before the product is released to production. www.irf.com 1 IR4007 ADVANCE INFORMATION Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to terminals stated, all currents are defined positive into any lead. The thermal resistance and power dissipation ratings are measured under board mounted and still air conditions. Symbol Definition Terminals Max. Ratings Units Note IDpeak Peak drain current 3-1 20 IDmax Maximum switching current 3-1 5.0 A V2-3 = 0.78V Tc=25oC EAS Single pulse avalanche energy 3-1 100 mJ Vdd=50V,L=10mH, Tc=25oC VCC Power supply voltage 4-3 35 VTH OCP/FB terminal voltage 5-2 6 P D1 Power dissipation for MOSFET 3-1 Single pulse V TBA TBA P D2 Power dissipation for control part (MIC) 4-2 0.8 RthJC Thermal resistance, junction to case -- 1.7 TJ Junction temperature -- -55-150 TS Storage temperature -- -40-125 Tf Internal frame temperature in operation -- -20-125 TOP Ambient operating temperature -- -20-125 TL Lead temp. (soldering, 10 seconds) -- 300 With infinite heatsink W Without heatsink Specified by VIN x IIN C/W C Refer to recommended operating temperature Recommended Operating Conditions Time for input of quasi resonant signals. For the Quasi resonant signal inputted to the VDCP/FB terminal at the time of quasi resonant operation, the signal should be wider thant Tth(2) 2 VOCP/FB Tth(2) 1.0s Vth(2) www.irf.com IR4007 ADVANCE INFORMATION Electrical Characteristics (for Control IC) VCC = 18V, (TA = 25C) unless otherwise specified. Symbol Definition Min. Typ. Max. Units Test Conditions VCCUV+ VCC supply undervoltage positive going threshold 14.4 16 17.6 VCCUV- VCC supply undervoltage negative going threshold 9 10 11 IQCCUV UVLO mode quiescent current -- -- 100 A Quiescent operating VCC supply current -- -- 30 mA Maximum OFF time 45 -- 55 Minimum input pulse width for quasi resonant signals -- -- 1.0 Minimum OFF time -- -- 1.5 IQCC TOFF/(MAX) TTH(2) TOFF/(MIN) VTH(1) OCP/FB terminal threshold voltage 1 0.68 0.73 0.78 VTH(2) OCP/FB terminal threshold voltage 2 1.3 1.45 1.6 OCP/FB terminal sink current 1.2 1.35 1.5 VCC overvoltage protection limit IOCP/FB VCC(OVP) ICC(LA) VCC(LaOFF) TJ(TSD) V sec V mA 20.5 22.5 24.5 V Latch circuit holding current -- -- 400 A Latch circuit reset voltage 6.6 -- 8.4 V -- oC Thermal shutdown activation temperature 140 -- VCC < VCCUV+ Electrical Characteristics (for MOSFET) (TA = 25C) unless otherwise specified. Symbol Definition Min. Typ. Max. Units Test Conditions VDSS Drain-to-source breakdown voltage 200 -- -- V IDSS Drain leakage current -- -- 250 A Vds=160V, VCC=0V Tj =125oC RDS(ON) tr THj-C On-resistance -- -- 0.4 Rise time (10% to 90%) Thermal resistance -- -- -- -- 200 1.7 ns oC/W www.irf.com V3-1=10V, ID=5A Between junction and case 3 IR4007 ADVANCE INFORMATION Block Diagram 4 Vcc 3 START O.V.P D LATCH DRIVE REG. 1 OSCILLATOR T.S.D S Vth(1) + 5 Comp.1 - OCP/ FB Vth(2) + Comp.2 2 Ground Lead Assignments 1 2 3 4 Pin # S y m b o l Description 1 S MOSFET Source terminal 2 Ground 3 D MOSFET Drain terminal 4 Vcc Control circuit supply voltage 5 OCP/FB Ground terminal 5 Overcurrent detection, and Voltage mode control feedback signal Other Functions O.V.P. - Overvoltage Protection Circuit T.S.D. - Thermal Shutdown Circuit 4 www.irf.com ADVANCE INFORMATION IR4007 IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245 Tel: (310) 252-7105 IR EUROPEAN REGIONAL CENTRE: 439/445 Godstone Rd., Whyteleafe, Surrey CR3 0BL, United Kingdom Tel: ++ 44 (0) 20 8645 8000 IR JAPAN: K&H Bldg., 2F, 30-4 Nishi-Ikebukuro 3-Chome, Toshima-Ku, Tokyo, Japan 171-0021 Tel: 8133 983 0086 IR HONG KONG: Unit 308, #F, New East Ocean Centre, No. 9 Science Museum Road, Tsimshatsui East, Kowloon Hong Kong Tel: (852) 2803-7380 Data and specifications subject to change without notice. 10/19/2000 www.irf.com 5