1. General description
The 74LVC2G53 is a high-performance, low-power, low-voltage, Si-gate CMOS device
that provides superior performance to most advanced CMOS compatible TTL families.
The 74LVC2G53 provides one analog multiplexer/demultiplexer with a digital select input
(S), two independent inputs/outputs (B0 and B1), a common input/output (A) and an
active LOW enable input (E). When pin E is HIGH, the switch is turned off.
The 74LVC2G53 can handle both analog and digital signals.
2. Features
nWide supply voltage range from 1.65 V to 5.5 V
nVery low ON resistance:
u7.5 Ω (typical) at VCC = 2.7 V
u6.5 Ω (typical) at VCC = 3.3 V
u6Ω (typical) at VCC =5V
nHigh noise immunity
nESD protection:
uHBM JESD22-A114-C exceeds 2000 V
uMM JESD22-A115-A exceeds 200 V
uCDM JESD22-C101-C exceeds 1000 V
nCMOS low-power consumption
nLatch-up performance meets requirements of JESD 78 Class I
nDirect interface with TTL levels
nControl inputs accepts voltages up to 5 V
nMultiple package options
nSpecified from −40 °C to +85 °C and from −40 °C to +125 °C
74LVC2G53
2-channel analog multiplexer/demultiplexer
Rev. 02 — 31 March 2006 Product data sheet
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 2 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
3. Quick reference data
4. Ordering information
5. Marking
Table 1. Quick reference data
GND = 0 V; t
r
=t
f
≤
2.5 ns; minimum and maximum values at T
amb
=
−
40
°
C to +85
°
C;
typical values at T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit
ton turn-on time
S to A or Bn CL= 50 pF; RL= 500 Ω
VCC = 3.3 V 1.8 3.4 5.0 ns
VCC = 5.0 V 1.3 2.6 3.8 ns
E to A or Bn CL= 50 pF; RL= 500 Ω
VCC = 3.3 V 1.2 2.2 3.8 ns
VCC = 5.0 V 1.0 1.7 2.6 ns
toff turn-off time
S to A or Bn CL= 50 pF; RL= 500 Ω
VCC = 3.3 V 1.1 4.0 5.4 ns
VCC = 5.0 V 1.0 2.9 3.8 ns
E to A or Bn CL= 50 pF; RL= 500 Ω
VCC = 3.3 V 2.0 3.7 5.0 ns
VCC = 5.0 V 1.3 2.9 3.8 ns
Ciinput capacitance - 2.5 - pF
CS(OFF) OFF-state capacitance - 6.0 - pF
CS(ON) ON-state capacitance - 18 - pF
Table 2. Ordering information
Type number Package
Temperature range Name Description Version
74LVC2G53DP −40 °C to +125 °C TSSOP8 plastic thin shrink small outline package;
8 leads; body width 3 mm; lead length 0.5 mm SOT505-2
74LVC2G53DC −40 °C to +125 °C VSSOP8 plastic very thin shrink small outline package;
8 leads; body width 2.3 mm SOT765-1
74LVC2G53GT −40 °C to +125 °C XSON8 plastic extremely thin small outline package;
no leads; 8 terminals; body 1 ×1.95 ×0.5 mm SOT833-1
Table 3. Marking
Type number Marking code
74LVC2G53DP V53
74LVC2G53DC V53
74LVC2G53GT V53
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 3 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
6. Functional diagram
7. Pinning information
7.1 Pinning
Fig 1. Logic symbol
Fig 2. Logic diagram
001aad386
S
A
E
B0
B16
7
2
5
1
001aad387
A
B0
S
B1
E
Fig 3. Pin configuration TSSOP8 and
VSSOP8 Fig 4. Pin configuration XSON8
74LVC2G53
AV
CC
EB0
GND B1
GND S
001aae798
1
2
3
4
6
5
8
7
74LVC2G53
B1
B0
VCC
S
GND
E
A
GND
001aae800
36
27
18
45
Transparent top view
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 4 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
7.2 Pin description
8. Functional description
8.1 Function table
[1] H = HIGH voltage level;
L = LOW voltage level;
X = don’t care;
Z = high-impedance OFF-state.
Table 4. Pin description
Symbol Pin Description
A 1 common A output or input
E 2 enable input (active LOW)
GND 3 ground (0 V)
GND 4 ground (0 V)
S 5 select input
B1 6 independent B1 input or output
B0 7 independent B0 input or output
VCC 8 supply voltage
Table 5. Function table[1]
Input Channel on
S E
L L B0 to A or A to B0
H L B1 to A or A to B1
X H Z (switch off)
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 5 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
9. Limiting values
[1] The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
[2] For TSSOP8 package: above 55 °C the value of Ptot derates linearly with 2.5 mW/K.
For VSSOP8 package: above 110 °C the value of Ptot derates linearly with 8 mW/K.
For XSON8 package: above 45 °C the value of Ptot derates linearly with 2.4 mW/K.
10. Recommended operating conditions
[1] To avoid drawing VCC current out of terminal A when switch current flows in terminal Bn, the voltage drop
across the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminal A, no VCC
current will flow out of terminal Bn. In this case, there is no limit for the voltage drop across the switch.
[2] Applies to control signal levels.
Table 6. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134).
Voltages are referenced to GND (ground = 0 V).
Symbol Parameter Conditions Min Max Unit
VCC supply voltage −0.5 +6.5 V
VIinput voltage [1] −0.5 +6.5 V
IIK input clamping
current VI<−0.5 V or VI>V
CC + 0.5 - −50 mA
ISK switch clamping
current VI<−0.5 V or VI>V
CC + 0.5 - ±50 mA
VSW switch voltage enable and disable mode −0.5 VCC + 0.5 V
ISW switch current VSW = −0.5 V to (VCC + 0.5 V) - ±50 mA
ICC quiescent supply
current - 100 mA
IGND ground current - −100 mA
Tstg storage temperature −65 +150 °C
Ptot total power
dissipation Tamb =−40 °C to +125 °C[2] - 300 mW
Table 7. Recommended operating conditions
Symbol Parameter Conditions Min Typ Max Unit
VCC supply voltage 1.65 - 5.5 V
VIinput voltage 0 - 5.5 V
VSW switch voltage enable and disable
mode [1] 0- V
CC V
Tamb ambient temperature −40 - +125 °C
∆t/∆V input transition rise and
fall rate VCC = 1.65 V to 2.7 V [2] 0 - 20 ns/V
VCC = 2.7 V to 5.5 V [2] 0 - 10 ns/V
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 6 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
11. Static characteristics
Table 8. Static characteristics
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions Min Typ Max Unit
Tamb =−40 °C to +85 °C[1]
VIH HIGH-state input voltage VCC = 1.65 V to 1.95 V 0.65VCC -- V
VCC = 2.3 V to 2.7 V 1.7 - - V
VCC = 3 V to 3.6 V 2.0 - - V
VCC = 4.5 V to 5.5 V 0.7VCC -- V
VIL LOW-state input voltage VCC = 1.65 V to 1.95 V - - 0.35VCC V
VCC = 2.3 V to 2.7 V - - 0.7 V
VCC = 3 V to 3.6 V - - 0.8 V
VCC = 4.5 V to 5.5 V - - 0.3VCC V
ILI input leakage current on pin S and pin E;
VI= 5.5 V or GND; VCC = 5.5 V -±0.1 ±2µA
IS(OFF) OFF-state leakage current per channel;
VSW = GND and VO=V
CC
or VSW =V
CC and VO= GND;
VCC = 5.5 V; see Figure 5
-±0.1 ±5µA
IS(ON) ON-state leakage current per channel;
VSW = GND or VCC;V
CC = 5.5 V;
see Figure 6
-±0.1 ±5µA
ICC quiescent supply current VI=V
CC or GND;
VSW = GND or VCC; IO=0A;
VCC = 5.5 V
- 0.1 10 µA
∆ICC additional quiescent supply
current per input pin;
VI=V
CC −0.6 V; VSW = GND or VCC;
IO= 0 A; VCC = 5.5 V
- 5 500 µA
Ciinput capacitance - 2.5 - pF
CS(OFF) OFF-state capacitance - 6.0 - pF
CS(ON) ON-state capacitance - 18 - pF
Tamb =−40 °C to +125 °C
VIH HIGH-state input voltage VCC = 1.65 V to 1.95 V 0.65VCC -- V
VCC = 2.3 V to 2.7 V 1.7 - - V
VCC = 3 V to 3.6 V 2.0 - - V
VCC = 4.5 V to 5.5 V 0.7VCC -- V
VIL LOW-state input voltage VCC = 1.65 V to 1.95 V - - 0.35VCC V
VCC = 2.3 V to 2.7 V - - 0.7 V
VCC = 3 V to 3.6 V - - 0.8 V
VCC = 4.5 V to 5.5 V - 0.3VCC V
ILI input leakage current on pin S and pin E;
VI= 5.5 V or GND; VCC = 5.5 V --±10 µA
IS(OFF) OFF-state leakage current per channel;
VSW = GND and VO=V
CC
or VSW =V
CC and VO= GND;
VCC = 5.5 V; see Figure 5
--±20 µA
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 7 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
[1] Typical values are measured at Tamb =25°C.
IS(ON) ON-state leakage current per channel;
VSW = GND or VCC;V
CC = 5.5 V;
see Figure 6
--±20 µA
ICC quiescent supply current VI=V
CC or GND;
VSW = GND or VCC; IO=0A;
VCC = 5.5 V
--40µA
∆ICC additional quiescent supply
current per input pin;
VI=V
CC −0.6 V; VSW = GND or VCC;
IO= 0 A; VCC = 5.5 V
- - 5000 µA
Table 8. Static characteristics
…continued
At recommended operating conditions; voltages are referenced to GND (ground 0 V).
Symbol Parameter Conditions Min Typ Max Unit
VSW =V
CC or GND; VO= GND or VCC.
Fig 5. Test circuit for measuring switch OFF-state current
VSW =V
CC or GND.
Fig 6. Test circuit for measuring switch ON-state current
VO
ISW
ISW
001aad390
S
AE
B0
B1
VCC
GND
switch
switch
1
12
2
VIH
VIL
S
VIH
VIH
E
VSW
VIL or VIH
VIH
ISW
001aad391
S
AE
B0
B1
VCC
GND
VIH
VIL
S
VIL
VIL
E
VSW
VIL or VIH
VIL
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 8 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
Table 9. Resistance Ron
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit Figure 7.
Symbol Parameter Conditions Min Typ Max Unit
Tamb =−40 °C to +85 °C[1]
RON(rail) ON resistance (rail) VSW = GND
ISW = 4 mA; VCC = 1.65 V to 1.95 V - 8.7 18 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - 7.2 16 Ω
ISW = 12 mA; VCC = 2.7 V - 7.0 14 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - 6.5 12 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - 5.9 10 Ω
VSW =V
CC
ISW = 4 mA; VCC = 1.65 V to 1.95 V - 12 30 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - 8.3 20 Ω
ISW = 12 mA; VCC = 2.7 V - 7.8 18 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - 6.7 15 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - 5.2 10 Ω
RON(peak) ON resistance (peak) VSW = GND to VCC
ISW = 4 mA; VCC = 1.65 V to 1.95 V - 57 130 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - 15 30 Ω
ISW = 12 mA; VCC = 2.7 V - 13 25 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - 9.0 20 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - 6.0 15 Ω
RON(flat) ON resistance (flatness) VSW = GND to VCC; see Figure 9
ISW = 4 mA; VCC = 1.65 V to 1.95 V - 100 - Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - 17 - Ω
ISW = 12 mA; VCC = 2.7 V - 10 - Ω
ISW = 24 mA; VCC =3Vto3.6V - 5 - Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - 3 - Ω
Tamb =−40 °C to +125 °C
RON(rail) ON resistance (rail) VSW = GND
ISW = 4 mA; VCC = 1.65 V to 1.95 V - - 27 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - - 24 Ω
ISW = 12 mA; VCC = 2.7 V - - 21 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - - 18 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - - 15 Ω
VSW =V
CC
ISW = 4 mA; VCC = 1.65 V to 1.95 V - - 45 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - - 30 Ω
ISW = 12 mA; VCC = 2.7 V - - 27 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - - 23 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - - 15 Ω
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 9 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
[1] Typical values are measured at Tamb =25°C and nominal VCC.
RON(peak) ON resistance (peak) VSW = GND to VCC
ISW = 4 mA; VCC = 1.65 V to 1.95 V - - 130 Ω
ISW = 8 mA; VCC = 2.3 V to 2.7 V - - 55 Ω
ISW = 12 mA; VCC = 2.7 V - - 35 Ω
ISW = 24 mA; VCC = 3 V to 3.6 V - - 25 Ω
ISW = 32 mA; VCC = 4.5 V to 5.5 V - - 20 Ω
Table 9. Resistance Ron
…continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V); see test circuit Figure 7.
Symbol Parameter Conditions Min Typ Max Unit
RON = VSW / ISW
Fig 7. Test circuit for measuring switch ON resistance
ISW
VSW
001aad392
S
AE
B0
B1
VCC
GND
switch
switch
1
12
2
VIH
VIL
S
VIL
VIL
E
VSW
VIL or VIH
VIL
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 10 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
(1) VCC = 1.8 V
(2) VCC = 2.5 V
(3) VCC = 2.7 V
(4) VCC = 3.3 V
(5) VCC = 5.0 V
Tamb =25°C
Fig 8. Typical switch ON resistance as a function of input voltage
VSW (V)
054231
001aad406
20
10
30
40
RON
(Ω)
0
(1)
(3) (4)
(5)
(2)
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 11 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
(1) Tamb = 125 °C
(2) Tamb =85°C
(3) Tamb =25°C
(4) Tamb =−40 °C
(1) Tamb = 125 °C
(2) Tamb =85°C
(3) Tamb =25°C
(4) Tamb =−40 °C
a. VCC = 1.8 V b. VCC = 2.5 V
(1) Tamb = 125 °C
(2) Tamb =85°C
(3) Tamb =25°C
(4) Tamb =−40 °C
(1) Tamb = 125 °C
(2) Tamb =85°C
(3) Tamb =25°C
(4) Tamb =−40 °C
c. VCC = 2.7 V d. VCC = 3.3 V
Fig 9. Switch ON resistance as a function of switch voltage
VSW (V)
054231
001aad410
40
20
60
80
RON
(Ω)
0
(1)
(2)
(3)
(4)
VSW (V)
054231
001aad407
8
4
12
16
RON
(Ω)
0
(1)
(2)
(3)
(4)
VSW (V)
054231
001aad408
8
4
12
16
RON
(Ω)
0
(1)
(2)
(3)
(4)
VSW (V)
054231
001aad409
8
4
12
16
RON
(Ω)
0
(1)
(2)
(3)
(4)
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 12 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
12. Dynamic characteristics
Table 10. Dynamic characteristics
At recommended operating conditions; voltages are referenced to GND (ground = 0 V);
test circuit Figure 12.
Symbol Parameter Conditions Min Typ Max Unit
Tamb =−40 °C to +85 °C[1]
tPHL HIGH-to-LOW
propagation delay see Figure 10
A to Bn or Bn to A VCC = 1.65 V to 1.95 V - - 2 ns
VCC = 2.3 V to 2.7 V - - 1.2 ns
VCC = 2.7 V - - 1.0 ns
VCC = 3 V to 3.6 V - - 0.8 ns
VCC = 4.5 V to 5.5 V - - 0.6 ns
tPLH LOW-to-HIGH
propagation delay see Figure 10
A to Bn or Bn to A VCC = 1.65 V to 1.95 V - - 2 ns
VCC = 2.3 V to 2.7 V - - 1.2 ns
VCC = 2.7 V - - 1.0 ns
VCC = 3 V to 3.6 V - - 0.8 ns
VCC = 4.5 V to 5.5 V - - 0.6 ns
ton turn-on time see Figure 11
S to A or Bn VCC = 1.65 V to 1.95 V 2.6 6.7 10.3 ns
VCC = 2.3 V to 2.7 V 1.9 4.1 6.4 ns
VCC = 2.7 V 1.9 4.0 5.5 ns
VCC = 3 V to 3.6 V 1.8 3.4 5.0 ns
VCC = 4.5 V to 5.5 V 1.3 2.6 3.8 ns
E to A or Bn VCC = 1.65 V to 1.95 V 1.9 4.0 7.3 ns
VCC = 2.3 V to 2.7 V 1.4 2.5 4.4 ns
VCC = 2.7 V 1.1 2.6 3.9 ns
VCC = 3 V to 3.6 V 1.2 2.2 3.8 ns
VCC = 4.5 V to 5.5 V 1.0 1.7 2.6 ns
toff turn-off time see Figure 11
S to A or Bn VCC = 1.65 V to 1.95 V 2.1 6.8 10.0 ns
VCC = 2.3 V to 2.7 V 1.4 3.7 6.1 ns
VCC = 2.7 V 1.4 4.9 6.2 ns
VCC = 3 V to 3.6 V 1.1 4.0 5.4 ns
VCC = 4.5 V to 5.5 V 1.0 2.9 3.8 ns
E to A or Bn VCC = 1.65 V to 1.95 V 2.3 5.6 8.6 ns
VCC = 2.3 V to 2.7 V 1.2 3.2 4.8 ns
VCC = 2.7 V 1.4 4.0 5.2 ns
VCC = 3 V to 3.6 V 2.0 3.7 5.0 ns
VCC = 4.5 V to 5.5 V 1.3 2.9 3.8 ns
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 13 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
[1] Typical values are measured at Tamb =25°C and nominal VCC.
Tamb =−40 °C to +125 °C
tPHL HIGH-to-LOW
propagation delay see Figure 10
A to Bn or Bn to A VCC = 1.65 V to 1.95 V - - 2.5 ns
VCC = 2.3 V to 2.7 V - - 1.5 ns
VCC = 2.7 V - - 1.25 ns
VCC = 3 V to 3.6 V - - 1.0 ns
VCC = 4.5 V to 5.5 V - - 0.8 ns
tPLH LOW-to-HIGH
propagation delay see Figure 10
A to Bn or Bn to A VCC = 1.65 V to 1.95 V - - 2.5 ns
VCC = 2.3 V to 2.7 V - - 1.5 ns
VCC = 2.7 V - - 1.25 ns
VCC = 3 V to 3.6 V - - 1.0 ns
VCC = 4.5 V to 5.5 V - - 0.8 ns
ton turn-on time see Figure 11
S to A or Bn VCC = 1.65 V to 1.95 V 2.6 - 12.9 ns
VCC = 2.3 V to 2.7 V 1.9 - 8.0 ns
VCC = 2.7 V 1.8 - 7.0 ns
VCC = 3 V to 3.6 V 1.8 - 6.3 ns
VCC = 4.5 V to 5.5 V 1.3 4.8 ns
E to A or Bn VCC = 1.65 V to 1.95 V 1.9 - 9.2 ns
VCC = 2.3 V to 2.7 V 1.4 - 5.5 ns
VCC = 2.7 V 1.1 - 4.9 ns
VCC = 3 V to 3.6 V 1.2 - 4.8 ns
VCC = 4.5 V to 5.5 V 1.0 - 3.3 ns
toff turn-off time see Figure 11
S to A or Bn VCC = 1.65 V to 1.95 V 2.1 - 12.5 ns
VCC = 2.3 V to 2.7 V 1.4 - 7.7 ns
VCC = 2.7 V 1.4 - 7.8 ns
VCC = 3 V to 3.6 V 1.1 - 6.8 ns
VCC = 4.5 V to 5.5 V 1.0 4.8 ns
E to A or Bn VCC = 1.65 V to 1.95 V 2.3 - 11.0 ns
VCC = 2.3 V to 2.7 V 1.2 - 6.0 ns
VCC = 2.7 V 1.4 - 6.5 ns
VCC = 3 V to 3.6 V 2.0 - 6.3 ns
VCC = 4.5 V to 5.5 V 1.3 - 4.8 ns
Table 10. Dynamic characteristics
…continued
At recommended operating conditions; voltages are referenced to GND (ground = 0 V);
test circuit Figure 12.
Symbol Parameter Conditions Min Typ Max Unit
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 14 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
13. Waveforms
Measurement points are given in Table 11.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 10. Input (Bn or A) to output (A or Bn) propagation delays
Measurement points are given in Table 11.
Logic levels: VOL and VOH are typical output voltage drop that occur with the output load.
Fig 11. Turn-on and turn-off times
Table 11. Measurement points
Supply voltage Input Output
VCC VMVMVXVY
1.65 V to 2.7 V 0.5VCC 0.5VCC VOL + 0.15 V VOH −0.15 V
2.7 V to 5.5 V 0.5VCC 0.5VCC VOL + 0.3 V VOH −0.3 V
tPLH tPHL
VM
VM
VM
VM
GND
VI
VOH
VOL
Bn or A
input
A or Bn
output
001aac361
VM
VI
GND
VCC
VOL
VOH
GND
S, E input
output
LOW to OFF
OFF to LOW
output
HIGH to OFF
OFF to HIGH
VM
001aad393
VM
ton
toff ton
VX
VY
switch
disabled switch
enabled
switch
enabled
A, Bn
A, Bn
toff
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 15 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
14. Additional dynamic characteristics
Test data is given in Table 12.
Definitions test circuit:
RT = termination resistance (should be equal to output impedance Zo of the pulse generator).
CL = load capacitance (including jig and probe capacitance).
RL = load resistance.
VEXT = external voltage for measuring switching times.
Fig 12. Load circuitry for switching times
Table 12. Test data
Supply voltage Input Load VEXT
VCC VItr, tfCLRLtPLH, tPHL ton, toff
HIGHtoOFF
OFF to HIGH LOW to OFF
OFF to LOW
1.65 V to 1.95 V VCC ≤2.0 ns 30 pF 1 kΩopen GND 2 × VCC
2.3 V to 2.7 V VCC ≤2.0 ns 30 pF 500 Ωopen GND 2 × VCC
2.7 V VCC ≤2.5 ns 50 pF 500 Ωopen GND 2 × VCC
3 V to 3.6 V VCC ≤2.5 ns 50 pF 500 Ωopen GND 2 × VCC
4.5 V to 5.5 V VCC ≤2.5 ns 50 pF 500 Ωopen GND 2 × VCC
VEXT
VCC
VIVO
mna616
DUT
CL
RT
RL
RL
PULSE
GENERATOR
Table 13. Additional dynamic characteristics
At recommended operating conditions; typical values measured at T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit
THD total harmonic
distortion fi= 600 Hz to 20 kHz;
RL= 600 Ω; CL=50pF;
Vi= 0.5 V (p-p); see Figure 13
VCC = 1.65 V - 0.260 - %
VCC = 2.3 V - 0.078 - %
VCC = 3.0 V - 0.078 - %
VCC = 4.5 V - 0.078 - %
f(-3dB) −3 dB frequency
response RL=50Ω; CL= 5 pF;
see Figure 14 [1]
VCC = 1.65 V - 200 - MHz
VCC = 2.3 V - 300 - MHz
VCC = 3.0 V - 300 - MHz
VCC = 4.5 V - 300 - MHz
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 16 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
[1] Adjust fi voltage to obtain 0 dBm level at output. Increase fi frequency until dB meter reads −3dB.
[2] Adjust fi voltage to obtain 0 dBm level at input.
[3] Definition: Qinj =∆VO×CL. Guaranteed by design.
αOFF(ft) OFF-state
feed-through
attenuation
RL=50Ω; CL= 5 pF;
fi= 10 MHz; see Figure 15 [2]
VCC = 1.65 V - −42 - dB
VCC = 2.3 V - −42 - dB
VCC = 3.0 V - −40 - dB
VCC = 4.5 V - −40 - dB
Vct(sw-sw) crosstalkbetween
switches RL=50Ω; CL= 5 pF;
fi= 10 MHz; see Figure 16
VCC = 1.65 V - −68 - dBV
VCC = 2.3 V - −70 - dBV
VCC = 3.0 V - −70 - dBV
VCC = 4.5 V - −70 - dBV
Qinj charge injection CL= 0.1 nF; Vgen =0V;
Rgen =0Ω; fi= 1 MHz;
RL=1MΩ; see Figure 17
[3]
VCC = 1.8 V - < 0.003 - pC
VCC = 2.5 V - 0.004 - pC
VCC = 3.3 V - 0.0045 - pC
VCC = 4.5 V - 0.0045 - pC
VCC = 5.5 V - 0.0045 - pC
Fig 13. Test circuit for measuring total harmonic distortion
Table 13. Additional dynamic characteristics
…continued
At recommended operating conditions; typical values measured at T
amb
=25
°
C.
Symbol Parameter Conditions Min Typ Max Unit
D
001aad394
600 Ω
10 µF
0.1 µFS
A
B0
B1
VCC 0.5VCC
GND
CL
RL
switch
switch
1
12
2
VIH
VIL
S
VIL
VIL
E
fi
VIL or VIH
E
VIL
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 17 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
Fig 14. Test circuit for measuring the frequency response when switch is in ON-state
Fig 15. Test circuit for measuring feed-through attenuation when switch is in OFF-state
Fig 16. Test circuit for measuring crosstalk between switches
dB
001aad395
50 Ω
0.1 µF
S
A
E
B0
B1
VCC 0.5VCC
GND
CL
RL
switch
switch
1
12
2
VIH
VIL
S
VIL
VIL
E
fi
VIL or VIH
VIL
dB
001aad396
50 Ω
RL
0.1 µFS
AE
B0
B1
VCC 0.5VCC
0.5VCC
GND
CL
RL
switch
switch
1
12
2
VIH
VIL
S
VIH
VIH
E
fi
VIL or VIH
VIH
dB
001aad397
50 Ω
0.1 µFS
AE
B0
B1
VCC 0.5VCC
GND
CL
RL
0.5VCC
RL
VIH
VIL
S20log10(VB1/VI)
20log10(VB0/VI)
test condition
VIL
VIL
E
fi
VIL or VIH
VIL
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 18 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
∆VO = output voltage variation
Rgen = generator resistance
Vgen = generator voltage
Fig 17. Test circuit for measuring charge injection
001aad398
S
A
B0
B1
RLCL
VCC
GND
Rgen
Vgen
switch
1
2
logic
input
(S) VO
E
VIL
001aac478
∆VO
offonoff
logic
input
VO
(S)
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 19 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
15. Package outline
Fig 18. Package outline SOT505-2 (TSSOP8)
UNIT A1
A
max. A2A3bpLHELpwyv
ceD(1) E(1) Z(1) θ
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
mm 0.15
0.00 0.95
0.75 0.38
0.22 0.18
0.08 3.1
2.9 3.1
2.9 0.65 4.1
3.9 0.70
0.35 8°
0°
0.13 0.10.20.5
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
0.47
0.33
SOT505-2 - - - 02-01-16
wM
bp
D
Z
e
0.25
14
85
θ
A2A1
Lp
(A3)
detail X
A
L
HE
E
c
vMA
X
A
y
2.5 5 mm0
scale
TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm SOT505-2
1.1
pin 1 index
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 20 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
Fig 19. Package outline SOT765-1 (VSSOP8)
UNIT A1
A
max. A2A3bpLHELpwyv
ceD(1) E(2) Z(1) θ
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
mm 0.15
0.00 0.85
0.60 0.27
0.17 0.23
0.08 2.1
1.9 2.4
2.2 0.5 3.2
3.0 0.4
0.1 8°
0°
0.13 0.10.20.4
DIMENSIONS (mm are the original dimensions)
Notes
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
0.40
0.15
Q
0.21
0.19
SOT765-1 MO-187 02-06-07
wM
bp
D
Z
e
0.12
14
85
θ
A2A1
Q
Lp
(A3)
detail X
A
L
HE
E
c
vMA
X
A
y
2.5 5 mm0
scale
VSSOP8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm SOT765-1
1
pin 1 index
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 21 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
Fig 20. Package outline SOT833-1 (XSON8)
terminal 1
index area
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC JEITA
SOT833-1 - - -
MO-252
- - -
SOT833-1
04-07-22
04-11-09
DIMENSIONS (mm are the original dimensions)
XSON8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm
D
E
e1
e
A1
b
L
L1
e1e1
0 1 2 mm
scale
Notes
1. Including plating thickness.
2. Can be visible in some manufacturing processes.
UNIT
mm 0.25
0.17 2.0
1.9 0.35
0.27
A1
max b E
1.05
0.95
Dee
1L
0.40
0.32
L1
0.50.6
A(1)
max
0.5 0.04
1
8
2
7
3
6
4
5
8×
(2)
4×
(2)
A
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 22 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
16. Abbreviations
17. Revision history
Table 14. Abbreviations
Acronym Description
CMOS Complementary Metal Oxide Semiconductor
TTL Transistor-Transistor Logic
HBM Human Body Model
ESD ElectroStatic Discharge
MM Machine Model
CDM Charged Device Model
DUT Device Under Test
Table 15. Revision history
Document ID Release date Data sheet status Change notice Supersedes
74LVC2G53_2 20060331 Product data sheet - 74LVC2G53_1
Modifications: •Added: type number 74LVC2G53DP (TSSOP8 package)
74LVC2G53_1 20060110 Product data sheet - -
74LVC2G53_2 © Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet Rev. 02 — 31 March 2006 23 of 24
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
18. Legal information
18.1 Data sheet status
[1] Please consult the most recently issued document before initiating or completing a design.
[2] The term ‘short data sheet’ is explained in section “Definitions”.
[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.semiconductors.philips.com.
18.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. Philips Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local Philips Semiconductors
sales office. In case of any inconsistency or conflict with the short data sheet,
the full data sheet shall prevail.
18.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, Philips Semiconductors does not give any representations
or warranties, expressed or implied, as to the accuracy or completeness of
such information and shall have no liability for the consequences of use of
such information.
Right to make changes — Philips Semiconductors reserves the right to
make changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — Philips Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a Philips Semiconductors product can reasonably be expected
to result in personal injury, death or severe property or environmental
damage. Philips Semiconductors accepts no liability for inclusion and/or use
of Philips Semiconductors products in such equipment or applications and
therefore such inclusion and/or use is for the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. Philips Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — Philips Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.semiconductors.philips.com/profile/terms, including those
pertaining to warranty, intellectual property rights infringement and limitation
of liability, unless explicitly otherwise agreed to in writing by Philips
Semiconductors. In case of any inconsistency or conflict between information
in this document and such terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
18.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
19. Contact information
For additional information, please visit: http://www.semiconductors.philips.com
For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
Document status[1][2] Product status[3] Definition
Objective [short] data sheet Development This document contains data from the objective specification for product development.
Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.
Product [short] data sheet Production This document contains the product specification.
Philips Semiconductors 74LVC2G53
2-channel analog multiplexer/demultiplexer
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
For more information, please visit: http://www.semiconductors.philips.com.
For sales office addresses, email to: sales.addresses@www.semiconductors.philips.com.
Date of release: 31 March 2006
Document identifier: 74LVC2G53_2
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
20. Contents
1 General description . . . . . . . . . . . . . . . . . . . . . . 1
2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2
4 Ordering information. . . . . . . . . . . . . . . . . . . . . 2
5 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
6 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3
7 Pinning information. . . . . . . . . . . . . . . . . . . . . . 3
7.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
7.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4
8 Functional description . . . . . . . . . . . . . . . . . . . 4
8.1 Function table. . . . . . . . . . . . . . . . . . . . . . . . . . 4
9 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5
10 Recommended operating conditions. . . . . . . . 5
11 Static characteristics. . . . . . . . . . . . . . . . . . . . . 6
12 Dynamic characteristics . . . . . . . . . . . . . . . . . 12
13 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
14 Additional dynamic characteristics . . . . . . . . 15
15 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 19
16 Abbreviations. . . . . . . . . . . . . . . . . . . . . . . . . . 22
17 Revision history. . . . . . . . . . . . . . . . . . . . . . . . 22
18 Legal information. . . . . . . . . . . . . . . . . . . . . . . 23
18.1 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 23
18.2 Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
18.3 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
18.4 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
19 Contact information. . . . . . . . . . . . . . . . . . . . . 23
20 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
