EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet Reverse Package Chip LED with Inner Lens 25-21/BHC-APR/2A Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. Descriptions The 25-21 SMD Taping is much smaller than lead frame type components, thus it enables smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications, etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Part No. 25-21/BHC-APR/2A Chip Material Emitted Color InGaN Blue Lens Color Water Clear Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Package Outline Dimensions Notes: The tolerances unless mentioned are 0.1, unit = mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 2 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +90 Electrostatic Discharge ESD 150 V Power Dissipation Pd 110 mW IFP 100 mA Peak Forward Current (Duty 1/10 @1KHz) Soldering Temperature Reflow Soldering: 260 for 10sec Tsol Hand Soldering: 350 for 3sec. Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity IV 45 ----- 180 mcd Peak Wavelength p ---- 468 ---- nm d 464.5 ----- 476.5 nm Dominant Wavelength Spectrum Radiation Bandwidth ----- 35 ---- nm Viewing Angle 21/2 ----- 60 ---- deg Forward Voltage VF ----- 3.5 4.3 V Reverse Current IR ---- ---- 50 A Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 3 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Bin Range Of Dom. Wavelength Group A Bin Min Max A9 464.5 467.5 A10 467.5 470.5 A11 470.5 473.5 A12 473.5 476.5 Unit Condition nm IF =20mA Unit Condition mcd IF =20mA Bin Range Of Luminous Intensity Bin Min Max P 45.0 72.0 Q 72.0 112.0 R 112.0 180.0 Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 4 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 5 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Notes: The tolerances unless mentioned are 0.1, unit = mm. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 6 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel Note: The tolerances unless mentioned are 0.1, unit=mm. Moisture Resistant Packaging Label Aluminum moisture-proof bag Desiccant Label Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 7 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min.5 sec. Test Sample Ac/Re Hours/Cycles Size 22 Pcs. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 3 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 4 High Temperature Storage Temp. : 100 1000 Hrs. 22 PCS. 0/1 5 Low Temperature Storage Temp. : -40 1000 Hrs. 22 PCS. 0/1 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/85%R.H. 1000 Hrs. 22 PCS. 0/1 2 6 Min. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 8 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package: The LEDs should be kept at 30 or less and 70%RH or less(Floor life). However, it's recommended that the LEDs should be used within 168 hours(7 days) after opening the package.If unused LEDs remain, it should be stored in moisture proof packages. 2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 9 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru EVERLIGHT ELECTRONICS CO.,LTD. 25-21/BHC-APR/2A 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 10 of 10 Device No.: SZDSE-251-B01 Prepared date: 3-Mar.-2005 Prepared by: Mao-Jinru