CHRISTIE WARNER Electrical Contractor HOLEMAKING Knockout, drive, drill, cut & punch. You'll get through it with Greenlee. * New 3-4 tooth-design holesaws are 20% faster than ordinary holesaws * High speed cutters offer lowest cost per hole and last ten times longer than ordinary holesaws for clean, burr-free edges * The patented Greenlee 724 Steel Stud Punch is designed to manually punch a square hole in steel studs. Better yet, the patented design rolls the edges over, decreasing the potential of hang-ups in the installation of armored cable and PVC conduit for applications where code does not require a bushing * Quick Draw(R) Flex Driver features a fully flexible neck to position the knockout punch in the desired location Quick Draw(R) Flex Driver 4 724 Steel Stud Punch USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Holemaking Selection Guide MATERIAL THICKNESS NUMBER OF HOLES PRODUCTS APPLICATION CONSIDERATIONS PAGES Steel 10GA Highest Slugsplitter Punches 8-9 Stainless Steel 10GA 10GA 10GA 8GA 10GA 10GA 10GA High High High Medium Medium Low Highest Slugbuster Punches Standard Punches High Speed Cutters Carbide-Tipped Hole Cutters Step Bits Hole Saws Slugsplitter Punches 10GA 9GA Medium Medium Slugbuster Punches Kwik Change Cutters 8GA 10GA 18 inches Medium Low High Carbide-Tipped Hole Cutters Hole Saws Naileater Power Bits 2-2 x 4's High E-Z Bore Bits 2x4 16 inches 1-5/8" or 2 x 4 High Medium Medium Step Bits Spade Bits Hole Saws Aluminum 10GA Highest Slugsplitter Punches Fiberglass/Plastic 10GA 10GA 10GA 10GA 10GA approx. 1/8" High High High Medium Low Highest Slugbuster Punches Standard Punches High-Speed Cutters Step Bits Hole Saws Slugsplitter Punches approx. 1/8" approx. 1/8" approx. 1/8" approx. 1/8" 1-5/8" 7/8" 7/8" 7/8" High High High Medium Low High Medium Medium High Medium Medium Medium Slugbuster Punches Standard Punches High-Speed Cutters Step Bits Hole Saws Recessed light hole saws Quick Cutter Keyhole Saw Slugbuster Punches Carbide-Grit Hole Saws Carbide-Grit Hole Saws Carbide-Grit Hole Saws D'versibits Non-round Punches Reciprocating Blades Jigsaw Blades Standard Punches Stud Punches Maximum durability and universal material usage Maximum hole size 2-1/2 inches Maximum hole size 2-1/2 inches Maximum hole size 5-5/8 inches Maximum hole size 2-1/2 inches Maximum hole size 2-1/2 inches Maximum hole size 1-3/8 inches Maximum hole size 6 inches Maximum durability and universal material usage Maximum hole size 2-1/2 inches Maximum hole size 2-1/2 inches Maximum hole size 3 inches, quick change cutting heads Maximum hole size 2-1/2 inches Run at 200 RPM, high pressure (150 lbs.) Cuts through nails, good chip removal, max hole size 1-1/4 inches Self feed screw for hard or soft woods, max hole size 4-5/8 inches Maximum hole size 1-3/8 inches, low chip removal Maximum hole size 1-1/2 inches Best on thinner wood, low chip removal, max hole size 6 inches Maximum durability and universal material usage Maximum hole size 2-1/2 inches Maximum hole size 2-1/2 inches Maximum hole size 5-5/8 inches Maximum hole size 2-1/2 inches Maximum hole size 1-3/8 inches Maximum hole size 6 inches Maximum durability and universal material usage Maximum hole size 2-1/2 inches Maximum hole size 2-1/2 inches Maximum hole size 5-5/8 inches Maximum hole size 2-1/2 inches Maximum hole size 1-3/8 inches Maximum hole size 6 inches Replaceable blades Adjustable or fixed, sprinkler heads or lighting Non-round holes Wood Drywall/Ceiling Tile Quazite(R)* Enclosures approx. 1/8" Hardyboard siding Cement board Existing Wall Non-round hole Non-conduit sizes Metal Studs 16-10GA 20GA High Medium Medium High Remodeling, phone, cable, alarm installation Square, rectangular, electronic connector holes 10-23 11, 24-29 44 43 41 45-48 8-9 HOLEMAKING MATERIAL TYPE 10-23 42 43 45-48 52 53-54 41 58 45-48 8-9 10-23 11, 24-29 44 41 45-48 8-9 10-23 11, 24-29 44 41 45-48 59 59 59 10-23 46 46 46 55-57 33-35 49 50 11 39-40 *Quazite is a registered trademark of Strongwell Corporation 5 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Knockout Punch and Driver Selection Guide Knockout Punch Knockout Punch Driver PUNCH TYPE DRIVE METHOD CAPACITY SIZE RANGE AVAILABLE PAGES Slug-Splitter Ratchet, Hydraulic or Battery Up thru 10 gauge (3.5 mm) stainless steel or mild steel .598" through 2.526" dia. (15.2 mm through 64 mm) 8 Slug-Buster(R) Manual, Ratchet, Hydraulic or Battery Up thru 10 gauge (3.5 mm) mild steel .492" through 2.52" dia. (12.5 mm through 64.0 mm) 10 Standard Round Manual, Ratchet, Hydraulic or Battery Up thru 10 gauge (3.5 mm) mild steel and aluminum 1/2" through 5-5/8" dia. (12.7 through 143.7 mm) 11, 25 (R) DRIVER TYPE Battery-Powered or Corded Hydraulic Driver Hand Pump Hydraulic Driver with Ram Foot Pump Hydraulic Driver with Ram Quick DrawTM Flex Hydraulic Driver Quick Draw 90TM Hydraulic Driver Quick DrawTM Hydraulic Driver High Leverage Ratchet Driver 6 DESCRIPTION * Develops 6.7 tons of hydraulic force. * Available with three choice of battery chargers - 115, 230 or 12 volt. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee standard and Slug-Buster(R) knockout punches and 12 gauge (2.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Powerful hydraulic ram develops 11 tons of hydraulic force. * Punches up thru 10 gauge (3.5 mm) mild steel with Greenlee standard and Slug-Buster(R) knockout punches and 10 gauge (3.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Foot operation frees both hands to operate punch. * Powerful hydraulic ram develops 11 tons of hydraulic force. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard and Slug-Buster(R) knockout punches; and 10 gauge (3.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Allows unlimited driver orientation to simplify access to work area * Develops 8 tons of hydraulic force for easy punching. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard and Slug-Buster(R) knockout punches; and 10 gauge (3.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Right angle driver head rotates over 180 degrees for maximum flexibility in tight working areas. * Develops 8 tons of hydraulic force for easy punching. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard and Slug-Buster(R) knockout punches; and 10 gauge (3.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Perfect for fast, straight-on front panel punching. * Develops 8 tons of hydraulic force for easy punching. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard and Slug-Buster(R) knockout punches; and 10 gauge (3.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. * Time saving ball bearing head punches faster than wrench method. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee Standard Slug-Buster(R) knockout punches; and16 gauge (1.5 mm) stainless steel with Greenlee Slug-Splitter(R) knockout punches. KITS Available in kits with driver only or with driver and Slug-Buster(R) knockout punches. PAGES 15 Available in kits with driver only or with driver and either standard, Slug-Buster(R)or Slug-Splitter(R) knockout punches. 19 Available in kits with driver only or with driver and either standard, Slug-Buster(R) or Slug-Splitter(R) knockout punches. 17 21 Available in kits with driver only or with driver and Slug-Buster(R) knockout punches. 21 Available in kits with driver only or with driver and Slug-Buster(R) knockout punches. 21 Available in kits with driver only or with driver and Slug-Buster(R) knockout punches. 23 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Standard Round Punch to Slugbuster Punch Cross Reference UPC NO. 04006 04008 04010 06974 04232 17687 17690 17697 17700 04245 18331 21115 21316 24459 24462 24476 24477 35192 36282 36505 36506 36686 36687 36688 36689 36882 36910 06978 04062 22563 22564 22565 02408 02409 02433 20670 25340 20673 20671 20668 25427 20676 20679 20678 18886 18887 18890 18891 18892 15909 32804 15910 19973 19974 22566 22567 22568 03986 DESCRIPTION 1/2" STANDARD PUNCH 3/4" STANDARD PUNCH 1" STANDARD PUNCH 1-1/4" STANDARD PUNCH PUNCH 2.00 (50.8) PUNCH 1.85 (47.0) PUNCH 2.36 (60.0) PUNCH 0.80 (20.4) PUNCH 0.73 (18.6) PUNCH 2.12 (54.0) PUNCH 1.45 (37.0) PUNCH UNIT PG 9 (15.2) PUNCH 0.59 (15.2) PUNCH 1.28 (32.5) PUNCH 1.59 (40.5) PUNCH UNIT 1.28 (32.5) PUNCH UNIT 1.59 (40.5) PUNCH UNIT 0.63 (16.2) 1-7/32" STANDARD PUNCH PUNCH UNIT 1.21 (30.5) 1-7/32" STANDARD PUNCH UNIT PUNCH SET PG 9 (30.5) PUNCH SET PG9 (48) PUNCH SET ISO 16-40 PUNCH SET ISO 16-64 PUNCH 1.11 (28.3) PUNCH UNIT 1.11 (28.3) 1-1/2" STANDARD PUNCH 2" STANDARD PUNCH 1/2" STANDARD PUNCH UNIT 3/4" STANDARD PUNCH UNIT 1" STANDARD PUNCH UNIT PUNCH UNIT 0.50 (12.7) PUNCH UNIT 0.62 (15.9) PUNCH UNIT 0.56 (14.3) PUNCH UNIT 1.00 (25.4) PUNCH UNIT 0.68 (17.5) PUNCH UNIT 1.25 (31.8) PUNCH UNIT 1.12 (28.6) PUNCH UNIT 0.81 (20.6) PUNCH UNIT 1.37 (34.9) PUNCH UNIT 2.00 (50.8) PUNCH UNIT 2.50 (63.5) PUNCH UNIT 2.12 (54.0) PUNCH UNIT 0.73 (18.6) PUNCH UNIT 0.80 (20.4) PUNCH UNIT 1.45 (37.0) PUNCH UNIT 1.85 (47.0) PUNCH UNIT 2.36 (60.0) HYDRAULIC PUNCH SET PUNCH SET HYDRAULIC PUNCH SET 1/2" to 1-1/4" STANDARD KNOCKOUT KIT 1-1/2" - 2" STANDARD KNOCKOUT KIT 1-1/4" STANDARD PUNCH UNIT 1-1/2" STANDARD PUNCH UNIT 2" STANDARD PUNCH UNIT PUNCH 1.00 (25.4) SLUGBUSTER CAT. NO. 721-1/2 721-3/4 721-1 721-1-1/4 35160 721E-47 721E-60 721E-20.4 721E-18.6 36172 721E-37.0 7211EBB-15.2 721E-15.2 35169 35158 35179 35180 35177 60237 60246 60246 36690 36691 36692 36693 721E-28.3 7211EBB-28.3 721-1-1/2 721-2 7211BB-1/2 7211BB-3/4 7211BB-1 06727 35177 7211EBB-15.2 35178 7211EBB-18.6 35179 7211EBB-28.3 7211EBB-20.4 7211BB-1 35181 35182 36171 7211EBB-18.6 7211EBB-20.4 7211EBB-37 7211EBB-47 7211EBB-60 7306SB 36691 7310SB 7235BB 7237BB 7211BB-1-1/4 7211BB-1-1/2 7211BB-2 35165 UPC NO. 31756 31757 31758 31759 35160 32009 32011 31971 31970 36172 31975 31989 31969 35169 35158 35179 35180 35177 60237 60246 60246 36690 36691 36692 36693 31973 31993 31760 31761 31962 31963 31964 06727 35177 31989 35178 31990 35179 31993 31991 31964 35181 35182 36171 31990 31991 31995 31996 31998 34360 36691 34361 32013 32014 31965 31966 31967 35165 SIZE DIFFERENCE (SLUGBUSTER TO STANDARD) HOLEMAKING STANDARD CAT. NO. 121AV 123AV 125AV 127AV 1756AV 17687 17690 17697 17700 1783AV 18331 21115 21316 24459 24462 24476 24477 35192 36282 36505 36506 36686 36687 36688 36689 36882 36910 439AV 441AV 71BB 72BB 73BB 730-1/2 730-5/8 730-9/16 730BB-1 730BB-11/16 730BB-1-1/4 730BB-1-1/8 730BB-13/16 730BB-1-3/8 730BB-2 730BB-2-1/2 730BB-2-1/8 730EBB-18.6 730EBB-20.4 730EBB-37.0 730EBB-47.0 730EBB-60.0 7306 7309E 7310 735BB 737BB 74BB 75BB 76BB 87AV 12.5 mm vs.12.7 mm 16.2 mm vs.15.9 mm 15.2 mm vs.14.3 mm 18.6 mm vs.17.5 mm 32.5 mm vs.31.8 mm 28.3 mm vs.28.6 mm 20.4 mm vs.20.6 mm 34.6 mm vs.34.9 mm 64 mm vs.63.5 mm 7 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Slug-Splitter(R) Knockout Punches 0.598" to 2.520" Designed for stainless steel applications * Slug-Splitter(R) heavy-duty punches are designed to punch up through 10 gauge (3.5 mm) stainless steel. * Unique slug splitting design and tool steel construction easily punch 10 gauge (3.5 mm) mild steel and stainless steel. * Heavy-duty dies and stainless steel draw studs for longer life. * Excellent abrasion resistance for punching fiberglass and plastic. * Slug-Splitter(R) Punch Units consist of: punch, die and draw stud. Check individual punch for specific capacity. * U.S. Patent No. 4,543,722. SPECIFICATIONS Capacity Stainless steel up through 10 gauge (3.5 mm). Application 10 gauge stainless steel, mild steel, fiberglass and plastic enclosures. Unique Slug-Splitter(R) punch design creases slug as the punch is drawn into the die. PUNCH PUNCH CAT./UPC NO. 31117 31119 31120 28154 28156 36490 28158 31122 28160 31123 28162 31124 31125 28165 04599 04602 04605 04608 04611 04614 Slug is split in half as punching operation is completed. Split slugs fall free from the die and stud. Hole Sizes Conduit Sizes - Hole size is outside diameter of US conduit sizes. Example: 1/2" conduit size punch actually makes a 7/8" hole. Pg Sizes - European standard pipe sizes ISO Sizes - International Standards Organization pipe sizes. Operation Operate with battery, hydraulic or high leverage ratchet driver only. DIE DRAW STUDS HOLE SIZE DIE CONDUIT ACTUAL CAT./UPC NO. & PIPE O (INCH) O (mm) 31126 -- -- .598 15.2 31128 -- -- .732 18.6 31129 -- -- .803 20.4 28155 1/2" 7/8 .885 22.5 28157 3/4" -- 1.115 28.3 36489 -- 1-7/32 1.210 30.5 28159 1" 1-11/32 1.362 34.6 31135 -- -- 1.457 37.0 28161 1-1/4" 1-11/16 1.701 43.2 31131 -- -- 1.850 47.0 28163 1-1/2" 1-15/16 1.951 49.6 31132 -- -- 2.125 54.0 31133 -- -- 2.362 60.0 28166 2" 2-3/8 2.416 61.5 04598 -- -- 0.638 16.2 04601 -- 1 1.000 25.4 04603 -- -- 1.280 32.5 04607 -- -- 1.595 40.5 04609 -- 2 2.000 50.8 04613 -- -- 2.520 64.0 PG 9 11 13 16 21 -- -- 29 -- 36 -- 42 48 -- -- -- -- -- -- -- ISO -- -- 20 -- -- -- -- -- -- -- -- -- -- -- 16 25 32 40 50 63 CAPACITY DRAW STUDS STAINLESS STEEL HYDRAULIC DRIVERS RATCHET DRIVER* GA. (mm) 7804/7904 7646/7625 1904 12 2.5 29451 29451 30227 12 2.5 29451 29451 30227 12 2.5 29451 29451 30227 10 3.5 29451 29451 30227 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 -- 29452 12098 10 3.5 -- 29452 12098 10 3.5 -- 29452 12098 10 3.5 -- 29452 12098 10 3.5 -- 29452 12098 12 2.5 29451 29451 30227 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 31872 29452 12098 10 3.5 -- 29452 12098 10 3.5 -- 29452 12098 * 16 ga. stainless steel capacity with ratchet driver. PUNCH UNIT PUNCH UNIT - INCLUDES PUNCH, DIE & DRAW CAT. NO. UPC NO. 745R-1/2 30384 745H-1/2 29560 740H-1-7/32 29563 Oil Tight 8 HOLE SIZE CONDUIT & ACTUAL PIPE SIZE O INCH O mm 1/2" 7/8 .885 22.5 1/2" 7/8 .885 22.5 -- 1-7/32 1.210 30.5 * Battery-Powered or Corded Knockout Punch Driver CAPACITY STAINLESS STEEL WEIGHT GA mm LBS. kg 16 1.5 .6 .27 10 3.5 .7 .32 10 3.5 1.2 .54 DRIVER LS60*/ 1904 7804/7904 CLC60 7646/7625 DRAW STUD x 30227 x x x 29451 x x x 29452 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Slug-Splitter(R) Ram and Hand Pump Hydraulic Driver Punch Kit All Kits Feature * Slug-Splitter(R) Knockout Punches with capacities up through 10 gauge (3.5 mm) stainless steel. Refer to individual punch capacity ratings. 7506 Punch Kit 7506 Kit Features * Fast, easy and simple to operate. * Compact design makes this a perfect choice for use on construction sites and maintenance jobs. * Will also drive 751 Cable Cutter head. * Powerful 11-ton hydraulic ram. * 3-foot hose. CAT. NO. 744 7307 Punch Kit (driver not included) 7307 7506 HOLEMAKING Designed for stainless steel applications WEIGHT LBS. kg. UPC NO. DESCRIPTION 29619 1/2" through 1-1/4" Conduit Size Slug-Splitter(R) Knockout Punch Kit 29528 1/2" through 2" Conduit Size Slug-Splitter(R) Knockout Punch Kit 30385 1/2" through 2" Conduit Size Slug-Splitter(R) Knockout Punch Kit with Hydraulic Ram and Hand Pump 5 2.3 10.4 4.7 32 14.5 SPECIFICATIONS Operation 744/29619 - Quick Draw(R), Quick Draw 90(R) and Quick Draw(R) Flex hydraulic drivers, Battery-Powered drivers, 7646 and 7625 ram-type drivers. 7307/29528 - Quick Draw(R), Quick Draw 90(R) and Quick Draw(R) Flex hydraulic drivers, Battery-Powered drivers, 7646 and 7625 ram-type drivers. 7506/30385 - Hydraulic ram and hand pump included. 744 Punch Kit (driver not included) Draw Studs and Misc. Punches and Dies NOTE: See Slug-Splitter(R) Knockout Punch Units on page 8 for list of individual punches, dies and draw studs. CAT. NO. 28154 28155 28156 28157 36490 36489 28158 28159 28160 28161 28162 28163 28165 28166 29451 29452 29529 19193 31068 746SS 29452 54167 54168 15908 1924AA 1925AA 1926AA 767 38316 54169 54170 06302 UPC NO. 28154 28155 28156 28157 36490 36489 28158 28159 28160 28161 28162 28163 28165 28166 29451 29452 29529 19193 31068 30387 29452 54167 54168 15908 03248 03249 06904 13284 38316 54169 54170 06302 CONDUIT & PIPE SIZE 1/2" 1/2" 3/4" 3/4" HOLE SIZE ACTUAL O INCH 7/8 .885 7/8 .885 -- 1.115 -- 1.115 1-7/32 1.210 1-7/32 1.210 1-11/32 1.362 1-11/32 1.362 1-11/16 1.701 1-11/16 1.701 1-15/16 1.951 1-15/16 1.951 2-3/8 2.416 2-3/8 2.416 DESCRIPTION O mm 1/2" Conduit Size Punch 22.5 1/2" Conduit Size Die 22.5 3/4" Conduit Size Punch 28.3 3/4" Conduit Size Die 28.3 1-7/32" Punch Oiltight -- 30.5 1-7/32" Die Oiltight -- 30.5 1" Conduit Size Punch 1" 34.6 1" Conduit Size Die 1" 34.6 1-1/4" Conduit Size Punch 1-1/4" 43.2 1-1/4" Conduit Size Die 1-1/4" 43.2 1-1/2" Conduit Size Punch 1-1/2" 49.6 1-1/2" Conduit Size Die 1-1/2" 49.6 2" Conduit Size Punch 2" 61.5 2" Conduit Size Die 2" 61.5 7/16" x 4-1/4" Draw Stud 3/4" x 5-1/2" Draw Stud Metal Case Metal Case Metal Case Ram (includes 1 each of the following 3 items) - 3/4" x 5-1/2" Draw Stud - 1/4" Female Coupler - Dust Plug Spacer Group (includes 1 each of the following 3 items) - Spacer-Short - Spacer-Medium - Spacer-Long Hydraulic Hand Pump High Pressure Hose Unit-1/4" x 3' (includes 1 each of the following 3 items) - 1/4" Male Coupler - Dust Cap - High Pressure Hose-1/4" x 3' CAPACITY KIT CAT./UPC NO. STAINLESS STEEL 744/ 7307/ 7506/ GA mm 29619 29528 30385 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 10 3.5 9 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Slug-Buster(R) Knockout Punches 0.492" to 2.520" HOLEMAKING * * * * * * * The contractor's choice - worldwide. Unique punch profile splits slugs allowing easy slug removal. Use with battery-powered, hydraulic, ratchet or manual drivers. Uses standard Greenlee dies and draw studs. Slug Buster Punches available in sizes up thru 2.52" (64.0 mm). U.S. Patent #4,543,722. Standard round punches available up to 5 5/8" (144.1 mm). SPECIFICATIONS Capacity Mild steel up through 10 gauge (3.5 mm). Application Punch mild steel, aluminum, fiberglass and plastic. Hole Sizes Conduit Sizes - Hole size is outside diameter of US conduit sizes. Example: 1/2" conduit size punch actually makes a 7/8" hole. Pg Sizes - European standard pipe sizes. ISO Sizes - International Standards Organization pipe sizes. Unique Slug Buster(R) punch design creases slug as the punch is drawn into the die. Slug is split in half as punching operation is completed. Split slugs fall free from the die and stud. Operation Battery, hydraulic, ratchet or manual drivers. When used with ratchet, hydraulic or battery drivers, buy the punch and die only; the draw stud is part of the driver kit. PUNCH UNIT REPLACEMENT PARTS PUNCH UNIT INCLUDES PUNCH, DIE AND DRAW STUD CONDUIT & 10 CAT. NO. UPC NO. 06727 7211EBB-15.2 35177 7211EBB-18.6 7211EBB-20.4 7211BB-1/2 35178 7211BB-3/4 7211EBB-28.3 60246 36508 35179 7211BB-1 7211EBB-37 35180 7211BB-1-1/4 7211EBB-47 7211BB-1-1/2 35181 36171 7211EBB-60 7211BB-2 35182 06727 31989 35177 31990 31991 31962 35178 31963 31993 60246 36508 35179 31964 31995 35180 31965 31996 31966 35181 36171 31998 31967 35182 PIPE SIZE HOLE SIZE ACTUAL O INCH O mm PG CAPACITY MILD STEEL ISO -- -- 0.492 12.5 7 12 -- -- 0.598 15.2 9 -- -- -- 0.638 16.2 -- 16 -- -- 0.732 18.6 11 -- -- -- 0.803 20.4 13 20 1/2" 7/8 0.885 22.5 16 -- 1/2" 7/8 0.885 22.5 16 -- -- 1 1.000 25.4 -- 25 3/4" -- 1.115 28.3 -- -- 3/4" -- 1.115 28.3 -- -- -- -- 1.115 28.3 21 -- -- 1-7/32 1.210 30.5 -- -- -- 1-7/32 1.210 30.5 -- -- -- -- 1.280 32.5 -- 32 1" -- 1.362 34.6 -- -- 1" -- 1.362 34.6 10 -- -- -- 1.457 37.0 29 -- -- -- 1.595 40.5 -- 40 1-1/4" -- 1.701 43.2 -- -- 1-1/4" -- 1.701 43.2 -- -- -- -- 1.850 47.0 36 -- 1-1/2" -- 1.951 49.6 -- -- 1-1/2" -- 1.951 49.6 -- -- -- 2 2.000 50.8 -- 50 -- 2-1/8 2.125 54.0 42 -- -- -- 2.362 60.0 48 -- 2" 2-3/8 2.416 61.5 -- -- 2" 2-3/8 2.416 61.5 -- -- -- -- 2.520 64.0 -- 63 Individually Packaged in Point of Purchase clamshell for display opportunities WEIGHT REPLACEMENT PUNCH REPLACEMENT DIE REPLACEMENT MANUAL DRAW STUD GA. mm LBS. g CAT. NO. UPC NO. CAT. NO. UPC NO. CAT. NO. UPC NO. 16 14 14 14 14 10 10 14 10 10 14 10 14 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1.5 2.0 2.0 2.0 2.0 3.5 3.5 2.0 3.5 3.5 2.0 3.5 2.0 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 0.3 0.3 0.3 0.3 0.3 0.3 -- 0.5 0.8 -- 0.5 0.6 0.6 0.8 1 -- 1.2 1.2 1.3 -- 1.9 2.1 -- 2.3 2.5 2.8 3.2 -- 3.4 137 137 137 137 137 137 -- 227 363 -- 227 273 273 363 454 -- 545 545 590 -- 862 953 -- 1043 1134 1270 1452 -- 1542 06728 31969 35163 31970 31971 721-1/2 721-1/2P 35165 721-3/4 721-3/4P 31973 60237 36284 35169 721-1 721-1P 31975 35158 721-1-1/4 721-1/4P 31976 721-1-1/2 721-1-1/2P 35160 36172 31978 721-2 721-2P 35167 06728 31969 35163 31970 31971 31756 01980 35165 31757 01981 31973 60237 36284 35169 31758 01982 31975 35158 31759 01983 31976 31760 01984 35160 36172 31978 31761 01985 35167 06729 32002 35162 32003 32004 14722 14722P 35164 124AV 124AVP 32006 36278 36279 35168 126AV 126AVP 32008 35159 128AV 128AVP 32009 440AV 440AVP 35161 36173 32011 442AV 442AVP 35166 06729 32002 35162 32003 32004 14722 01992 35164 06972 01993 32006 36278 36279 35168 04011 01994 32008 35159 04013 01995 32009 04061 01996 35161 36173 32011 04063 01997 35166 1675AV 00042 00042 00042 00042 00042 00042P 249AVBB 249AVBB 249AVBBP 00042 249AVBB 00042 249AVBB 249AVBB 249AVBBP 249AVBB 249AVBB 249AVBB 249AVBBP 304AVBB 304AVBB 304AVBBP 304AVBB 304AVBB 304AVBB 304AVBB 304AVBBP 304AVBB 04218 00042 00042 00042 00042 00042 06678 04040 04040 01987 00042 04040 00042 04040 04040 01987 04040 04040 04040 01987 04042 04042 01988 04042 04042 04042 04042 01988 04042 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Standard Round Knockout Punches 0.5" to 5.675" Bushing Die See page 25 for other sizes of standard round punches Draw Stud SPECIFICATIONS Capacity Mild steel up through 10 gauge (3.5 mm). Application Punch mild steel, aluminum, fiberglass and plastic. Hole Sizes Conduit Sizes - Hole size is outside diameter of US conduit sizes. Example: 1/2" conduit size punch actually makes a 7/8" hole. Pg Sizes - European standard pipe sizes. ISO Sizes - International Standards Organization pipe sizes. Operation Operate with battery-powered, hydraulic, ratchet or manual drivers. When used with battery-powered, hydraulic, or ratchet drivers buy the punch and die only; the draw stud is part of the driver kit. Punch Every cut quick and clean Slug falls free in die. ...Just tip it out. PUNCH UNIT REPLACEMENT PARTS PUNCH KIT-INCLUDES PUNCH, DIE & DRAW STUD CONDUIT & CAT. NO. UPC NO. PIPE SIZE 730-1/2 730-9/16 21115 730-5/8 35192 730BB-11/16 730EBB-18.6 730BB-3/4 730EBB - 20.4 730BB-13/16 730BB-15/16 730BB-1 730BB-1-1/16 730BB-1-1/8 36506 730BB-1-1/4 730BB-1-5/16 730BB-1-3/8 730BB-1-1/2 730BB-1-5/8 730BB-1-3/4 730BB-1-7/8 730BB-2-1/4 730BB-2-1/2 730PBB-2-5/8 730BB-2-3/4 730MBB 738BB 730BB-3 730TBB 730EBB-82 739BB 730PBB-3-3/4 741BB* 742BB* 730EBB-120* 743BB* HOLEMAKING * Round Standard Metal Punch Units are complete units consisting of punch, die and draw stud. * Use with battery-powered, hydraulic, ratchet or manual drivers. * Properly assembled through pilot holes, they will make clean, fast and accurate holes. Ball Bearing Nut 02408 02433 21115 02409 35192 25340 18886 20667 18887 20668 25341 20670 25342 20671 36506 20673 25344 25427 25428 25349 25350 25351 25360 20679 21214 25361 25383 19975 25372 25403 18635 19976 21216 19977 19978 21519 19980 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 2-1/2" -- -- -- 3" -- 3-1/2" 4" -- 5" HOLE SIZE CAPACITY ACTUAL MILD STEEL WEIGHT O INCH O mm PG ISO GA. mm LBS. g 1/2 9/16 -- 5/8 -- 11/16 -- 3/4 -- 13/16 15/16 1 1-1/16 1-1/8 1-7/32 1-1/4 1-5/16 1-3/8 1-1/2 1-5/8 1-3/4 1-7/8 2-1/4 2-1/2 2-5/8 2-3/4 -- 2-7/8 3 3-1/8 -- 3-1/2 3-3/4 4 4-1/2 -- 5-5/8 0.500 0.563 0.598 0.625 0.638 0.688 0.732 0.750 0.803 0.812 0.937 1.000 1.063 1.125 1.210 1.250 1.313 1.375 1.500 1.625 1.750 1.875 2.250 2.500 2.625 2.750 2.781 2.914 3.000 3.125 3.228 3.539 3.750 4.044 4.544 4.724 5.675 12.7 14.3 15.2 15.9 16.2 17.5 18.6 19.1 20.4 20.6 23.8 25.4 27.0 28.6 30.5 31.8 33.4 34.9 38.1 41.3 44.5 47.6 57.2 63.5 66.7 69.9 70.6 74.0 76.2 79.4 82.0 89.9 95.3 102.7 115.4 120.0 144.1 *CAT. NO. 3037AV 7 -- 9 -- -- -- 11 -- 13 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 16 -- -- -- 20 -- -- 25 -- -- -- -- -- -- -- -- -- -- -- 63 -- -- -- -- -- -- -- -- -- -- -- -- -- UPC NO. O4686 16 16 14 16 14 14 14 14 14 14 14 14 14 14 16 16 16 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 1.5 1.5 2.0 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 1.5 1.5 1.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 .1 .1 .3 .2 .3 .3 .3 .3 .3 .3 .5 .5 .5 .6 .6 .7 .7 1.1 1.2 1.4 1.5 1.9 2.6 3 5.1 4.8 3.8 5 6.1 6 6.3 5.9 7.7 10 11.4 13 19 46 46 137 91 137 137 137 137 137 137 227 227 227 273 273 318 318 499 545 636 681 862 1180 1361 2314 2178 1724 2268 2767 2722 2858 2677 3493 4536 5172 5897 8619 REPLACEMENT REPLACEMENT REPLACEMENT PUNCH REPLACEMENT DIE DRAW STUD BALL BEARING NUT CAT. NO. UPC NO. CAT. NO. UPC NO. CAT. NO. UPC NO. CAT. NO. UPC NO. 1760AV 1754AV 21316 1742AV 35193 1752AV 17700 113AV 17697 1745AV 1762AV 87AV 1763AV 91AV 36282 117AV 1747AV 3205AV 3207AV 1794AV 1816AV 1791AV 437AV 1758AV 1795AV 1790AV 730101A 1429AV 1821AV 1798AV 18905 1431AV 4640AV 2982AV 2984AV 21489 5135AV 06996 1759AV 04235 04230 1753AV 04229 21316 32002 32002 04223 1743AV 04224 35193 35162 35162 04228 1751AV 04227 17700 32003 32003 03998 114AV 03999 17697 32004 32004 04226 1744AV 04225 04238 1761AV 04237 03986 35164 35164 04240 1764AV 04242 03990 92AV 03991 36282 36279 36279 04002 118AV 04003 06587 1746AV 06586 04734 3206AV 04735 04736 3208AV 07044 04251 1793AV 04250 04257 1815AV 04256 04248 1792AV 04249 04058 438AV 04059 04234 1757AV 04233 04252 1796AV 06997 04247 1789AV 04246 02445 730100A 02443 04175 1430AV 04177 04259 1820AV 04258 06363 1797AV 06362 18905 18906 18906 04180 1432AV 04183 05265 4641AV 05266 04653 2981AV 04652 04655 2983AV 04654 21489 21491 21491 05447 5136AV 05448 1675AV 1675AV 00042 1675AV 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 249AVBB 249AVBB 249AVBB 249AVBB 304AVBB 304AVBB 304AVBB 1434AV 1434AV 304AVBB 1434AV 1434AV 1434AV 1434AV 1434AV 1434AV 3026AV 3026AV 3026AV 3026AV 04218 04218 00042 04218 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 00042 04040 04040 04040 04040 04042 04042 04042 04188 04188 04042 04188 04188 04188 04188 04188 04188 04679 04679 04679 04679 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1433AVBB 1433AVBB -- 1433AVBB 1433AVBB 1433AVBB 1433AVBB 1433AVBB 1433AVBB 3036AVBB 3036AVBB 3036AVBB 3036AVBB -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 04187 04187 -- 04187 04187 04187 04187 04187 04187 04685 04685 04685 04685 DESCRIPTION Replacement Bushing for 3-1/2" (conduit hole size) and larger punches with manual operation 11 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Slug-Buster(R) Knockout Kit with Ratchet Wrench CAT. NO. 7238SB UPC NO. DESCRIPTION 34757 1/2" - 2" Conduit Size Slug-Buster(R) Knockout Punch Kit CAPACITY MILD STEEL WEIGHT GA mm LBS. kg. 10 3.5 10 4.54 7238SB/34757 SLUG-BUSTER(R) KNOCKOUT PUNCH KIT INCLUDES * 1" Hex Ratchet Wrench allows use with both 3/8" (19.1 mm) and 3/4" (9.5 mm) draw studs. * High-impact, rugged plastic carrying case. CAT. NO. 34941 721-1/2 14722 721-3/4 124AV 721-1 126AV 721-1-1/4 128AV 721-1-1/2 440AV 721-2 442AV 00042 304AVBB 34758 UPC NO. 34941 31756 14722 31757 06972 31758 04011 31759 04013 31760 04061 31761 04063 00042 04042 34758 HOLE SIZE ACTUAL DESCRIPTION O INCH O mm Ratchet wrench - 1" Hex 1/2" Conduit Size Punch 7/8 .885 22.5 1/2" Conduit Size Die 7/8 .885 22.5 3/4" Conduit Size Punch -- 1.115 28.3 3/4" Conduit Size Die -- 1.115 28.3 1" Conduit Size Punch -- 1.362 34.6 1" Conduit Size Die -- 1.362 34.6 1-1/4" Conduit Size Punch -- 1.701 43.2 1-1/4" Conduit Size Die -- 1.701 43.2 1-1/2" Conduit Size Punch -- 1.951 49.6 1-1/2" Conduit Size Die -- 1.951 49.6 2" Conduit Size Punch 2-3/8 2.416 61.5 2" Conduit Size Die 2-3/8 2.416 61.5 Ball Bearing Draw Stud with 1" Hex Head-3/8" x 1-5/8" Draw Stud-3/4" x 2-15/16" Plastic Case PG 16 16 -- -- -- -- -- -- -- -- -- -- Slug-Buster(R) Manual Knockout Kits 7235BB CAT. NO. UPC NO. DESCRIPTION 7235BB 32013 7237BB 32014 1/2" - 1-1/4" Conduit Size Manual Slug-Buster(R) Knockout Punch Kit 1-1/2" and 2" Conduit Size Manual Slug-Buster(R) Knockout Punch Kit CAPACITY MILD STEEL WEIGHT GA mm LBS. kg. 10 3.5 2.7 1.2 10 3.5 5.2 2.4 7235BB/32013 SLUG-BUSTER(R) KNOCKOUT PUNCH KIT INCLUDES * Assortment of commonly used Slug-Buster(R) knockout punches, packaged to meet the contractor's needs. * High-impact, rugged plastic carrying case. 7237BB 12 CAT. NO. 721-1/2 14722 00042 721-3/4 124AV 721-1 126AV 721-1-1/4 128AV 249AVBB 31880 UPC NO. 31756 14722 00042 31757 06972 31758 04011 31759 04013 04040 31880 DESCRIPTION 1/2" Conduit Size Punch 1/2" Conduit Size Die Draw Stud-3/8" x 1-5/8" 3/4" Conduit Size Punch 3/4" Conduit Size Die 1" Conduit Size Punch 1" Conduit Size Die 1-1/4" Conduit Size Punch 1-1/4" Conduit Size Die Draw Stud-3/4" x 2-1/8" Plastic Case HOLE SIZE ACTUAL O INCH O mm PG 7/8 .885 22.5 16 7/8 .885 22.5 16 -- -- -- -- -- -- 1.115 1.115 1.362 1.362 1.701 1.701 28.3 28.3 34.6 34.6 43.2 43.2 -- -- -- -- -- -- 7237BB/32014 SLUG-BUSTER(R) KNOCKOUT PUNCH KIT INCLUDES CAT. NO. 721-1-1/2 440AV 721-2 442AV 304AVBB 32012 UPC NO. 31760 04061 31761 04063 04042 32012 DESCRIPTION 1-1/2" Conduit Size Punch 1-1/2" Conduit Size Die 2" Conduit Size Punch 2" Conduit Size Die Draw Stud-3/4" x 2-15/16" Plastic Case HOLE SIZE ACTUAL O INCH O mm PG -- 1.951 49.6 -- -- 1.951 49.6 -- 2-3/8 2.416 61.5 -- 2-3/8 2.416 61.5 -- USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Slug-Buster(R) Knockout Kit with Ratchet Wrench - Metric Draw Studs and Misc. Punches and Dies 36690 WEIGHT LBS. kg. CAT. NO. UPC NO. DESCRIPTION 36690 36690 Pg-9 through 30.5 mm Manual Slug-Buster(R) Metric Knockout Punch Kit 36691 36691 Pg-9 through Pg-48 and 30.5 mm Manual Slug-Buster(R) Metric Knockout Punch Kit 36692 36692 ISO-16 through ISO-40 Manual Slug-Buster(R) Metric Knockout Punch Kit 36693 36693 ISO-16 through ISO-63 Manual Slug-Buster(R) Metric Knockout Punch Kit HOLE SIZE ACTUAL O INCH O mm 4.7 2.1 9 4.1 5.6 2.5 9 4.1 PG ISO CAPACITY MILD STEEL GA mm 15.2 9 -- 14 2.0 15.2 9 -- 14 2.0 0.732 18.6 11 -- 14 2.0 0.732 18.6 11 -- 14 2.0 -- 0.803 20.4 13 20 14 2.0 -- 0.803 20.4 13 20 14 2.0 Pg-16 Slug-Buster(R) Punch 7/8 0.885 22.5 16 -- 10 3.5 14722 Pg-16 Die 7/8 0.885 22.5 16 -- 10 3.5 31973 31973 Pg-21 Slug-Buster Punch -- 1.115 28.3 21 -- 14 2.0 32006 32006 Pg-21 Die -- 1.115 28.3 21 -- 14 2.0 36284 36284 30.5 mm Slug-Buster(R) Punch 1-7/32 1.210 30.5 -- -- 14 2.0 36279 36279 30.5 mm Die 1-7/32 1.210 30.5 -- -- 14 2.0 31975 31975 Pg-29 Slug-Buster Punch -- 1.457 37.0 29 -- 10 3.5 32008 32008 Pg-29 Die -- 1.457 37.0 29 -- 10 3.5 31976 31976 Pg-36 Slug-Buster(R) Punch -- 1.850 47.0 36 -- 10 3.5 32009 32009 Pg-36 Die -- 1.850 47.0 36 -- 10 3.5 31978 31978 Pg-48 Slug-Buster Punch -- 2.362 60.0 48 -- 10 3.5 32011 32011 Pg-48 Die -- 2.362 60.0 48 -- 10 3.5 35163 35163 ISO-16 Slug-Buster(R) Punch -- 0.638 16.2 -- 16 14 2.0 35162 35162 ISO-16 Die -- 0.638 16.2 -- 16 14 2.0 35165 35165 ISO-25 Slug-Buster Punch 1 1.000 25.4 -- 25 14 2.0 35164 35164 ISO-25 Die 1 1.000 25.4 -- 25 14 2.0 35169 35169 ISO-32 Slug-Buster(R) Punch -- 1.280 32.5 -- 32 10 3.5 35168 35168 ISO-32 Die -- 1.280 32.5 -- 32 10 3.5 35158 35158 ISO-40 Slug-Buster Punch -- 1.595 40.5 -- 40 10 3.5 35159 35159 ISO-40 Die -- 1.595 40.5 -- 40 10 3.5 35160 35160 ISO-50 Slug-Buster(R) Punch 2 2.000 50.8 -- 50 10 3.5 35161 35161 ISO-50 Die 2 2.000 50.8 -- 50 10 3.5 35167 35167 ISO-63 Slug-Buster Punch 2-1/2 2.500 63.5 -- 63 10 3.5 35166 35166 ISO-63 Die 2-1/2 2.500 63.5 -- 63 10 3.5 CAT. NO. UPC NO. DESCRIPTION 31969 31969 Pg-9 Slug-Buster Punch -- 0.598 32002 32002 Pg-9 Die -- 0.598 31970 31970 Pg-11 Slug-Buster(R) Punch -- 32003 32003 Pg-11 Die -- 31971 31971 Pg-13 Slug-Buster Punch 32004 32004 Pg-13 Die 721-1/2 31756 14722 (R) (R) (R) (R) (R) (R) (R) (R) KIT CAT./UPC NO. 36690 36691 36692 36693 249AVBB 04040 Draw Stud - 3/4" x 2-1/8" 304AVBB 04042 Draw Stud - 3/4" x 2-15/16" 36018 36018 Kwik Stepper step bit 9.7 mm 34941 34941 Ratchet wrench - 1" Hex 00042 00042 Ball Bearing Drive Nut with 1" hex head, 3/8" x 3" 36685 36685 Plastic Case (R) HOLEMAKING * 1" (25.4 mm) hex ratchet wrench allows use with both 3/8" (9.5 mm) and 3/4" (19.1 mm) draw studs. * 9.7 mm Kwik Stepper(R) step bit included. * High-impact, rugged plastic carrying case. 13 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Slug-Buster(R) Knockout Punch Kits for Ratchet/ Hydraulic Drivers 14 * Packaged in carton for easy insertion into your existing case. * Replacement punch kits for battery-powered, hydraulic and ratchet drivers. CAT. NO. UPC NO. DESCRIPTION 721-1/2 14722 721-3/4 124AV 721-1 126AV 721-1-1/4 128AV 721-1-1/2 440AV 721-2 442AV 31969 32002 31970 32003 31971 32004 31973 32006 36284 36279 31975 32008 31976 32009 31978 32011 35163 35162 35165 35164 35169 35168 35158 35159 35160 35161 35167 35166 31756 14722 31757 06972 31758 04011 31759 04013 31760 04061 31761 04063 31969 32002 31970 32003 31971 32004 31973 32006 36284 36279 31975 32008 31976 32009 31978 32011 35163 35162 35165 35164 35169 35168 35158 35159 35160 35161 35167 35166 1/2" Conduit Size Punch 1/2" Conduit Size Die 3/4" Conduit Size Punch 3/4" Conduit Size Die 1" Conduit Size Punch 1" Conduit Size Die 1-1/4" Conduit Size Punch 1-1/4" Conduit Size Die 1-1/2" Conduit Size Punch 1-1/2" Conduit Size Die 2" Conduit Size Punch 2" Conduit Size Die Pg-9 Punch Pg-9 Die Pg-11 Punch Pg-11 Die Pg-13 Punch Pg-13 Die Pg-21 Punch Pg-21 Die 30.5 mm Punch 30.5 mm Die Pg-29 Punch Pg-29 Die Pg-36 Punch Pg-36 Die Pg-48 Punch Pg-48 Die ISO-16 Punch ISO-16 Die ISO-25 Punch ISO-25 Die ISO-32 Punch ISO-32 Die ISO-40 Punch ISO-40 Die ISO-50 Punch ISO-50 Die ISO-63 Punch ISO-63 Die CONDUIT & PIPE SIZE 1/2" 1/2" 3/4" 3/4" 1" 1" 1-1/4" 1-1/4" 1-1/2" 1-1/2" 2" 2" -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- CAT. NO. UPC NO. DESCRIPTION WEIGHT LBS. kg. 7216 32017 1/2" - 2" Conduit Size Knockout Punch and Die Kit 5.5 2.5 7214E 32398 Pg-9 through 30.5 mm Slug-Buster(R) Pg Punch Kit 1.3 7215E 32803 Pg-9 through Pg-48 and 30.5 mm Slug-Buster(R) Pg Punch Kit 5.1 2.3 35617 35617 ISO-16 through ISO-40 Slug-Buster(R) ISO Punch Kit 1.6 06892 06892 ISO-16 through ISO-63 Slug-Buster(R) ISO Punch Kit 5.5 2.5 HOLE SIZE ACTUAL O INCH O mm 7/8 7/8 -- -- -- -- -- -- -- -- 2-3/8 2-3/8 -- -- -- -- -- -- -- -- 1-7/32 1-7/32 -- -- -- -- -- -- -- -- 1 1 -- -- -- -- 2 2 -- -- .885 .885 1.115 1.115 1.362 1.362 1.701 1.701 1.951 1.951 2.416 2.416 .598 .598 .732 .732 .803 .803 1.115 1.115 1.210 1.210 1.457 1.457 1.850 1.850 2.362 2.362 0.638 0.638 1.000 1.000 1.280 1.280 1.595 1.595 2.000 2.000 2.520 2.520 22.5 22.5 28.3 28.3 34.6 34.6 43.2 43.2 49.6 49.6 61.5 61.5 15.2 15.2 18.6 18.6 20.4 20.4 28.3 28.3 30.5 30.5 37.0 37.0 47.0 47.0 60.0 60.0 16.2 16.2 25.4 25.4 32.5 32.5 40.5 40.5 50.8 50.8 64.0 64.0 .6 .7 PG CAPACITYKIT CAT./UPC NO. MILD STEEL 7216/ 7214E/ 7215E/ ISO GA mm 32017 32398 32803 35617 06892 16 16 -- -- -- -- -- -- -- -- -- -- 9 9 11 11 13 13 21 21 -- -- 29 29 36 36 48 48 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20 20 -- -- -- -- -- -- -- -- -- -- 16 16 25 25 32 32 40 40 50 50 63 63 10 10 10 10 10 10 10 10 10 10 10 10 14 14 14 14 14 14 14 14 10 10 10 10 10 10 10 10 14 14 14 14 10 10 10 10 10 10 10 10 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 2.0 2.0 2.0 2.0 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Gator-PlusTM Battery-Powered Knockout Punch Driver Kits HOLEMAKING * Punches a hole for 2" conduit (61.5 mm) in only 12 seconds. * Angled pistol grip allows easy one handed control and positioning. * Tool senses when the hole is completely punched and automatically shuts off to prevent damage to the punch and die. * Develops 6.7 tons of hydraulic force, capable of punching up to 2" conduit (61.5 mm) size holes in 10 gauge (3.5 mm) mild steel and 12 gauge (2.5 mm) stainless steel. * Three choices of battery chargers - 115 volt, 220 volt, or 12 volt. Punches approximately 80 1/2" conduit size holes or 40 2" conduit size holes in 10 gauge mild steel per battery charge. * U.S. Patents #6,065,326, and #6,206,663 LS6012A SPECIFICATIONS Weight (driver with battery only) 8.25 lbs. (3.7 kg) Overall Length (ram retracted) 10.3 in. (262 mm) Height Maximum Punch Force 11.5 in. (292 mm) 6.7 tons (60 kN) Maximum Round Punch Size (in 10 gauge mild steel) Maximum Square Punch Size (in 10 gauge mild steel) 2.42 in. dia. (61.5 mm dia.) CAT. NO. UPC NO. DESCRIPTION LS6011A 03557 LS6012A 03558 LS6022A 03559 LS6011B 04311 LS6012B 04661 2-11/16 in. x 2-11/16 in. (68.0 x 68.0 mm) Maximum Rectangular Punch Size (in 10 gauge mild steel) 1.378 x 2.559 in. (35.0 x 65.0 mm) Maximum Ram Travel 0.87 in (22 mm) Charging Time Approximately 1 hour Battery Voltage 12 volts NiCd LS6022B 04312 WEIGHT LBS. kg. Battery-powered driver with 115 volt charger, 2 batteries, 2 draw studs, 1 adapter, and 1 spacer and case Battery-powered driver with 12 volt charger, 2 batteries, 2 draw studs, 1 adapter, and 1 spacer and case Battery-powered driver with 220 volt charger, 2 batteries, 2 draw studs, 1 adapter, and 1 spacer and case Battery-powered driver with 115 volt charger, 2 batteries, 1/2" through 2" Slug-Buster(R) conduit size punches, 2 draw studs, 1 adapter, and 1 spacer and case Battery-powered driver with 12 volt charger, 2 batteries, 1/2" through 2" Slug-Buster(R) conduit size punches, 2 draw studs, 1 adapter, and 1 spacer and case Battery-powered driver with 220 volt charger, 2 batteries, 1/2" through 2" Slug-Buster(R) conduit size punches, 2 draw studs, 1 adapter, and 1 spacer and case 23 10.4 23 10.4 23 10.4 27 12.2 27 12.2 27 12.2 See page 17 for complete parts list for all kits. STEEL CAPACITIES FOR CONDUIT SIZES STANDARD PUNCHES AND SLUG-BUSTERS(R) 1/2" 3/4" 1-7/32" 1" 1-1/4" 1-1/2" 2" 1/2" 3/4" 1-7/32" 1" 1-1/4" 1-1/2" 2" CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. O 0.885" O 1.115" O 1.210" O 1.362" O 1.701" O 1.951" O 2.415" O 0.885" O 1.115" O 1.210" O 1.362" O 1.701" O 1.951" O 2.416" 22.5mm 28.3mm 30.5mm 34.6mm 43.2mm 49.6mm 61.5mm 22.5mm 28.3mm 30.5mm 34.6mm 43.2mm 49.6mm 61.5mm Electronic Connector Punches RS-232, 229, 231, 234, 238 STUD AND ACCESSORIES SLUG-SPLITTERS(R) 1614SS Draw Stud 1924AA Spacer 33967 Adapter 2 1924AA Spacer 29451 7/16" Draw Stud 2 29451 7/16" Draw Stud 1 1924AA Spacer 31872 3/4" Draw Stud 31872 3/4" Draw Stud 33967 Adapter 1 2 The Slug-Buster(R) punches may not split the slug when used with this adapter, because of the small pilot hole. 29451 sold separately. See page 37 for ordering information. 10 GA. (0.1345" [3.5 mm]) MILD STEEL 10 GA. (0.1345" [3.5 mm]) STAINLESS STEEL 12 GA. (0.1046" [2.5 mm]) STAINLESS STEEL 16 GA. (0.0598" [1.5 mm]) MILD STEEL AND 1/8" ALUMINUM 14 GA. (0.0747" [2 mm]) MILD STEEL 15 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Gator-PlusTM Corded Knockout Punch Driver Kits HOLEMAKING * Punches a hole for 2" conduit (61.5 mm) in only 12 seconds. * Angled pistol grip allows easy one handed control and positioning. * Tool senses when the hole is completely punched and automatically shuts off to prevent damage to the punch and die. * Develops 6.7 tons of hydraulic force, capable of punching up to 2" conduit (61.5 mm) size holes in 10 gauge (3.5 mm) mild steel and 12 gauge (2.5 mm) stainless steel. * Operates directly from 120V/60Hz or 230V/50Hz electrical outlets. No need to charge batteries or worry about running out of power. * Equipped with 15 foot (5 m) cord. Can be used with extension cords. * U.S. Patents #6,065,326, and #6,206,663 SPECIFICATIONS Weight (driver) 8.25 lbs. (3.7 kg) Overall Length (ram retracted) 10.3 in. (262 mm) Height Maximum Punch Force 11.5 in. (292 mm) 6.7 tons (60 kN) Maximum Round Punch Size (in 10 gauge mild steel) Maximum Square Punch Size (in 10 gauge mild steel) 2.42 in. dia. (61.5 mm dia.) 2-11/16 in. x 2-11/16 in. (68.0 x 68.0 mm) Maximum Rectangular Punch Size (in 10 gauge mild steel) 1.378 x 2.559 in. (35.0 x 65.0 mm) Maximum Ram Travel 0.87 in (22 mm) Operating Voltage 120V, 60Hz 230V, 50Hz WEIGHT LBS. kg CAT. NO. UPC NO. DESCRIPTION CLS6011A 01496 CLS6022A 01497 CLS6011B 01498 CLS6022B 01499 Corded driver, 120 volts/60Hz, with 2 draw studs, 1 adapter, and 1 spacer and case. Corded driver, 230 volts/50Hz, with 2 draw studs, 1 adapter, and 1 spacer and case. Corded driver, 120 volts/60Hz, with 1/2" through 2" Slug-Buster conduit size punches, 2 draw studs, 1 adapter, and 1 spacer and case. Corded driver, 230 volts/50Hz, with 1/2" through 2" Slug-Buster conduit size punches, 2 draw studs, 1 adapter, and 1 spacer and case. 23 10.4 23 10.4 23 10.4 27 12.2 See page 17 for complete parts list for all kits. STEEL CAPACITIES FOR CONDUIT SIZES STANDARD PUNCHES AND SLUG-BUSTERS(R) 1/2" 3/4" 1-7/32" 1" 1-1/4" 1-1/2" 2" 1/2" 3/4" 1-7/32" 1" 1-1/4" 1-1/2" 2" CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. CON. O 0.885" O 1.115" O 1.210" O 1.362" O 1.701" O 1.951" O 2.415" O 0.885" O 1.115" O 1.210" O 1.362" O 1.701" O 1.951" O 2.416" 22.5mm 28.3mm 30.5mm 34.6mm 43.2mm 49.6mm 61.5mm 22.5mm 28.3mm 30.5mm 34.6mm 43.2mm 49.6mm 61.5mm Electronic Connector Punches RS-232, 229, 231, 234, 238 STUD AND ACCESSORIES SLUG-SPLITTERS(R) 1614SS Draw Stud 1924AA Spacer 33967 Adapter 2 1924AA Spacer 29451 7/16" Draw Stud 2 29451 7/16" Draw Stud 1 1924AA Spacer 31872 3/4" Draw Stud 31872 3/4" Draw Stud 33967 Adapter 1 2 16 The Slug-Buster(R) punches may not split the slug when used with this adapter, because of the small pilot hole. 29451 sold separately. See page 37 for ordering information. 10 GA. (0.1345" [3.5 mm]) MILD STEEL 10 GA. (0.1345" [3.5 mm]) STAINLESS STEEL 12 GA. (0.1046" [2.5 mm]) STAINLESS STEEL 16 GA. (0.0598" [1.5 mm]) MILD STEEL AND 1/8" ALUMINUM 14 GA. (0.0747" [2 mm]) MILD STEEL USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Battery-Powered Knockout Punch Driver Kits Parts List Punches and Dies Draw Studs and Misc. CAT. NO. UPC NO. DESCRIPTION 721-1/2 31756 KIT CAT./UPC NO. LS6011A/03557 LS6011B/04311 ACTUAL LS6012A/03558 LS6012B/04661 CLS6011A CLS6011B O INCH O mm PG LS6022A/03559 LS6022B/04312 CLS6022A CLS6022B 1/2" Conduit Size Slug-Buster(R) Punch 1/2" 7/8 0.885 22.5 16 14722 14722 1/2" Conduit Size Die 1/2" 7/8 0.885 22.5 16 721-3/4 31757 3/4" Conduit Size Slug-Buster(R) Punch 3/4" -- 1.115 28.3 21 124AV 06972 3/4" Conduit Size Die 3/4" -- 1.115 28.3 21 721-1 31758 1" Conduit Size Slug-Buster(R) Punch 1" -- 1.362 34.6 -- 126AV 04011 1" Conduit Size Die 1" -- 1.362 34.6 -- 721-1-1/4 31759 1-1/4" Conduit Size Slug-Buster(R) Punch 1-1/4" 1-11/16 1.701 43.2 -- 128AV 04013 1-1/4" Conduit Size Die 1-1/4" 1-11/16 1.701 43.2 -- 721-1-1/2 31760 1-1/2" Conduit Size Slug-Buster(R) Punch 1-1/2" 1-15/16 1.951 49.6 -- 440AV 04061 1-1/2" Conduit Size Die 1-1/2" 1-15/16 1.951 49.6 -- 721-2 31761 2" Conduit Size Slug-Buster(R) Punch 2" 2-3/8 2.416 61.5 -- 442AV 04063 2" Conduit Size Die 2" 2-3/8 2.416 61.5 -- 1614SS 30043 Draw Stud-3/8" x 2-13/16" 31872 31872 Draw Stud-3/4" x 4-1/8" 1924AA 03248 Spacer-Short 33967 33967 Stud Adapter-3/8" 01686 01686 Metal Case Optional Accessories for LS6011B, LS6012B, and LS6022B (not included in kits) 29451 29451 Draw Stud-7/16" x 4-1/2" for Slug Splitter Stainless Steel Punches HOLEMAKING HOLE SIZE CONDUIT & PIPE SIZE Slug-Buster(R) Ram and Foot Pump Hydraulic Driver Kits * * * * * 7625 Foot operation frees both hands to operate punch. Punches 10 times faster than wrench method. Will also drive 751 Cable Cutter head. Powerful 11 ton hydraulic ram. Can be used with all standard round, Slug-Buster(R) and Slug-Splitter(R) punch sizes. * Can be used with non-round punches (adapter may be required). CAT. NO. UPC NO. DESCRIPTION WEIGHT LBS. kg. 7625 25097 Driver, foot pump, steel case 37 17 7606SB 07173 7610SB 07174 Driver, foot pump, Slug-Buster(R) punches, dies and draw studs for 1/2" through 2" conduit, steel case Driver, foot pump, Slug-Buster(R) punches, dies and draw studs for 1/2" through 4" conduit, steel case 42 19 60 27 STEEL CAPACITIES FOR CONDUIT SIZES REQUIRED DRAW STUD STANDARD & SLUG-BUSTER(R) PUNCHES STANDARD AND ACCESSORIES 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 3/4" Stud (03294), 3/8" Stud (30043) & Spacers 3/4" Stud (03294), Long Spacer 3/4" Stud (03294), Short Spacer 3/4" Stud (03294) 3/4" Stud (03294), & Sleeve (03170) 7/16" Stud (29451) 3/4" Stud (29452) & Spacer 10 GA. MILD STEEL 10 GA. STAINLESS STEEL 1/2" SLUG-SPLITTERS(R) 3/4" 1" 1-1/4" 1-1/2" 2" 17 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Ram and Foot Pump Kits Parts List Draw Studs and Misc. Punches and Dies HOLE SIZE CONDUIT & PIPE SIZE KIT CAT./UPC NO. ACTUAL O INCH O mm CAT. NO. UPC NO. DESCRIPTION 721-1/2 14722 721-3/4 124AV 31756 14722 31757 06972 721-1 126AV 31758 04011 721-1-1/4 128AV 31759 04013 721-1-1/2 440AV 31760 04061 721-2 442AV 1429AV 1430AV 1431AV 1432AV 2982AV 2981AV 2984AV 2983AV 746 2113AA 54167 54168 1557AA 1614SS 15908 1924AA 1925AA 1926AA 34410 1725 37729 31761 04063 04175 04177 04180 04183 04653 04652 04655 04654 17091 03294 54167 54168 03170 30043 15908 03248 03249 06904 34410 31353 37729 54169 54170 23955 25094 54169 54170 23955 25094 1/2" Conduit Size Slug-Buster(R) Punch 1/2" 7/8 0.885 22.5 1/2" Conduit Size Die 1/2" 7/8 0.885 22.5 3/4" Conduit Size Slug-Buster(R) Punch 3/4" -- 1.115 28.3 3/4" Conduit Size Die 3/4" -- 1.115 28.3 1" -- 1.362 34.6 1" Conduit Size Slug-Buster(R) Punch 1" Conduit Size Die 1" -- 1.362 34.6 1-1/4" 1-11/16 1.701 43.2 1-1/4" Conduit Size Slug-Buster(R) Punch 1-1/4" Conduit Size Die 1-1/4" 1-11/16 1.701 43.2 1-1/2" 1-15/16 1.951 49.6 1-1/2" Conduit Size Slug-Buster(R) Punch 1-1/2" Conduit Size Die 1-1/2" 1-15/16 1.951 49.6 2" 2-3/8 2.416 61.5 2" Conduit Size Slug-Buster(R) Punch 2" Conduit Size Die 2" 2-3/8 2.416 61.5 2-1/2" Conduit Size Punch 2-1/2" 2-7/8 2.914 74.0 2-1/2" Conduit Size Die 2-1/2" 2-7/8 2.914 74.0 3" Conduit Size Punch 3" 3-1/2 3.539 89.9 3" Conduit Size Die 3" 3-1/2 3.539 89.9 3-1/2" Conduit Size Punch 3-1/2" 4 4.044 102.7 3-1/2" Conduit Size Die 3-1/2" 4 4.044 102.7 4" Conduit Size Punch 4" 4-1/2 4.544 115.4 4" Conduit Size Die 4" 4-1/2 4.544 115.4 (A) Ram (includes 1 ea. of items B, C, and D) (B) Draw Stud-3/4" x 5-3/8" (C) Female Coupler-1/4" (D) Dust Plug (F) Punch Sleeve (G) Draw stud-3/8"x 2-13/16" (H) Spacer Group (includes 1 ea. of items I, J, and K) (I) Spacer-Short (J) Spacer-Medium (K) Spacer-Long (L) Kwik Stepper(R) Step Bit 1/2" (S) Hydraulic Foot Pump (includes 1 ea. - 54167 female coupler and 54168 dust plug) (T) High Pressure Hose Unit - 1/4" x 10'; filled with hydraulic oil; (includes the following 2 items) - Couplers - Dust Caps (U) Steel case Tray RAM AND FOOT PUMP HYDRAULIC DRIVER PARTS IDENTIFICATION (Match letters above to drawing.) UU AA T SS FF CC CC D D 18 D D HH GG BB LL PG 16 16 21 7625/ 25097 7606SB/ 07173 7610SB/ 07174 -- 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 1 2 2 1 1 2 2 1 1 21 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Slug-Buster(R) Ram and Hand Pump Hydraulic Driver Kits Fast, easy and simple to operate. Compact design for field use on construction sites and maintenance jobs. Punches 10 times faster than wrench method. Will also drive 751 Cable Cutter head. Can be used with all standard round, Slug-Buster(R) and Slug-Splitter(R) punch sizes. * Can be used with non-round punches (adapter may be required). * 3-foot hose. * Powerful 11-ton hydraulic ram. 7646 CAT. NO. 7646 UPC NO. DESCRIPTION 15906 Driver, hand pump, draw studs, adapter, spacers, Kwik Stepper(R) Step Bit and plastic case 7306SB 34360 Driver, hand pump, Slug-Buster(R) punches, dies and draw studs for 1/2" through 2" conduit, adapter, spacers, Kwik Stepper(R) Step Bit and plastic case 7310SB 34361 Driver, hand pump, Slug-Buster(R) punches, dies and draw studs for 1/2" through 2" and 2-1/2" through 4" standard conduit size punches, dies and draw studs, adapter, spacers, Kwik Stepper(R) Step Bit and steel case 7646PgSB 32799 Metric - Driver, Slug-Buster(R) Pg punches, dies and draw studs for 15.2 mm through 60.0 mm, adapter, spacers, Kwik Stepper(R) Step Bit and plastic case 38520 38520 Driver, hand pump, Slug-Buster(R) punches and draw studs for 1/2" through 3" and 4" conduit, adapter, spacers, Kwik Stepper(R) Step Bit and steel case WEIGHT LBS. kg. HOLEMAKING * * * * * 20 9.1 24 10.9 54 24.5 24 10.9 48 21.8 STEEL CAPACITIES FOR CONDUIT SIZES REQUIRED DRAW STUD AND ACCESSORIES 3/4" Stud (03294), 3/8" Stud (30043) & Spacers 3/4" Stud (03294), Long Spacer 3/4" Stud (03294), Short Spacer 3/4" Stud (03294) STANDARD & SLUG-BUSTER PUNCHES 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 2-1/2" STANDARD 3" 3-1/2" 4" 1/2" 3/4" SLUG-SPLITTERS(R) 1" 1-1/4" 1-1/2" 2" 3/4" Stud (03294), & Sleeve (03170) 7/16" Stud (29451) 3/4" Stud (29452) & Spacer 10 GA. MILD STEEL FF BB 10 GA. STAINLESS STEEL RAM AND HAND PUMP HYDRAULIC DRIVER PARTS IDENTIFICATION HH GG LL KK AA JJ I RR M M NN KEY A CAT./UPC NO. 746 / 17091 DESCRIPTION Ram (includes Item B) B 2113AA / 03294 Draw Stud-3/4" x 5-3/8" F 1557AA / 03170 Punch Sleeve G 1614SS / 30043 Draw Stud-3/8" x 2-13/16" H 15908 Spacer Group (includes Items I, J and K) I 1924AA / 03248 Spacer-Short J 1925AA / 03249 Spacer-Medium K 1926AA / 06904 Spacer-Long L 34410 Kwik Stepper(R) Step Bit 1/2" M 767 / 13284 Hydraulic Hand Pump N 06302 / 06302 High Pressure Hose-1/4" x 3' R 30206 Plastic Case 19 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Ram and Hand Pump Kits Parts List HOLE SIZE Draw Studs and Misc. Punches and Dies CAT. NO. 20 721-1/2 14722 721-3/4 124AV 721-1 126AV 721-1-1/4 128AV 721-1-1/2 440AV 721-2 442AV 1429AV 1430AV 1431AV 1432AV 2982AV 2981AV 2984AV 2983AV 31969 32002 31970 32003 31971 32004 31973 32006 36284 36279 31975 32008 31976 32009 31978 32011 746 2113AA 1557AA 1614SS 15908 1924AA 1925AA 1926AA 34410 767 06302 30206 18402 25094 CONDUIT & PIPE SIZE KIT CAT./UPC NO. ACTUAL O INCH O mm UPC NO. DESCRIPTION 31756 14722 31757 06972 31758 04011 31759 04013 31760 04061 31761 04063 04175 04177 04180 04183 04653 04652 04655 04654 31969 32002 31970 32003 31971 32004 31973 32006 36284 36279 31975 32008 31976 32009 31978 32011 17091 03294 03170 30043 15908 03248 03249 06904 34410 13284 06302 30206 18402 25094 1/2" Conduit Size Slug-Buster(R) Punch 1/2" 7/8 1/2" Conduit Size Die 1/2" 7/8 3/4" Conduit Size Slug-Buster(R) Punch 3/4" -- 3/4" Conduit Size Die 3/4" -- 1" Conduit Size Slug-Buster(R) Punch 1" -- 1" Conduit Size Die 1" -- 1-1/4" Conduit Size Slug-Buster(R) Punch 1-1/4" 1-11/16 1-1/4" Conduit Size Die 1-1/4" 1-11/16 1-1/2" Conduit Size Slug-Buster(R) Punch 1-1/2" 1-15/16 1-1/2" Conduit Size Die 1-1/2" 1-15/16 2" Conduit Size Slug-Buster(R) Punch 2" 2-3/8 2" Conduit Size Die 2" 2-3/8 2-1/2" Conduit Size Punch 2-1/2" 2-7/8 2-1/2" Conduit Size Die 2-1/2" 2-7/8 3" Conduit Size Punch 3" 3-1/2 3" Conduit Size Die 3" 3-1/2 3-1/2" Conduit Size Punch 3-1/2" 4 3-1/2" Conduit Size Die 3-1/2" 4 4" Conduit Size Punch 4" 4-1/2 4" Conduit Size Die 4" 4-1/2 Slug-Buster(R) Punch -- -- Die -- -- Slug-Buster(R) Punch -- -- Die -- -- Slug-Buster(R) Punch -- -- Die -- -- Slug-Buster(R) Punch 3/4" -- Die 3/4" -- 30.5 mm Slug-Buster(R) Punch -- 1-7/32 30.5 mm Die -- 1-7/32 Slug-Buster(R) Punch -- -- Die -- -- Slug-Buster(R) Punch -- -- Die -- -- Slug-Buster(R) Punch -- -- Die -- -- Ram (includes following item) - Draw Stud-3/4" x 5-3/8" Punch Sleeve Draw Stud-3/8"x 2-13/16" Spacer Group (includes 1 ea. of the following 3 items) - Spacer-Short - Spacer-Medium - Spacer-Long Kwik Stepper(R) Step Bit 1/2" Hydraulic Hand Pump High Pressure Hose-1/4" x 3' Plastic Case Steel Case Punch Tray 0.885 0.885 1.115 1.115 1.362 1.362 1.701 1.701 1.951 1.951 2.416 2.416 2.914 2.914 3.539 3.539 4.044 4.044 4.544 4.544 0.598 0.598 0.732 0.732 0.803 0.803 1.115 1.115 1.210 1.210 1.457 1.457 1.850 1.850 2.362 2.362 22.5 22.5 28.3 28.3 34.6 34.6 43.2 43.2 49.6 49.6 61.5 61.5 74.0 74.0 89.9 89.9 102.7 102.7 115.4 115.4 15.2 15.2 18.6 18.6 20.4 20.4 28.3 28.3 30.5 30.5 37.0 37.0 47.0 47.0 60.0 60.0 7646/ 7306SB/ 7310SB/ 7646PGSB/ PG ISO 15906 34360 34361 32799 38520 16 16 21 21 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 9 9 11 11 13 13 21 21 -- -- 29 29 36 36 48 48 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 20 20 -- -- -- -- -- -- -- -- -- -- 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Quick Draw(R) Hydraulic Punch Driver and Kits CAT. NO. 7704SB UPC NO. DESCRIPTION 10475 Quick Draw(R) Flex Driver, 2 draw studs, 1 adapters, 1 spacer and case 7706SB 10476 Standard - Quick Draw(R) Flex Driver, 1/2" through 2" Slug Buster(R) conduit size punches and dies 2 draw studs, 1 adapter, 1 spacer and case 7804SB 34292 Quick Draw(R) Driver, 2 draw studs, 1 adapter, 1 spacer and case 7806SB 34293 Standard - Quick Draw(R) Driver, 1/2" through 2" Slug Buster(R) conduit size punches and dies 2 draw studs, 1 adapter, 1 spacer and case 7804E 34291 Metric - Quick Draw(R) Driver, 2 draw studs, 1 adapter, 1 spacer and case 7804ESB 35611 Metric - Quick Draw(R) Driver, Slug-Buster(R) Pg punches and dies 15.2 mm through 30.5 mm, 2 draw studs, 1 adapter, 1 spacer and case 7804ISO 35614 Metric - Quick Draw(R) Driver, Slug-Buster(R) ISO punches and dies 16.2 mm through 40.5 mm, 2 draw studs, 1 adapter, 1 spacer and case 7904SB 33794 Quick Draw 90(R) Driver, 2 draw studs, 1 adapter, 1 spacer and case 7906SB 34300 Quick Draw 90(R) Driver, 1/2" through 2" SlugBuster(R) conduit size punches and dies, draw studs, 1 adapter, 1 spacer and case 7904E 34299 Metric - Quick Draw 90(R) Driver, 2 draw studs, 1 adapter, 1 spacer and case 7904ESB 35615 Metric - Quick Draw 90(R) Driver, Slug-Buster(R) Pg punches and dies 15.2 mm through 30.5 mm, 2 draw studs, 1 adapter, 1 spacer and case 7904ISO 35616 Metric - Quick Draw 90(R) Driver, Slug-Buster(R) ISO punches and dies 16.2 mm through 40.5 mm, 2 draw studs, 1 adapter, 1 spacer and case 7806SB Quick Draw Kit 7706 Flex Driver 7906SB Quick Draw 90 Kit HOLEMAKING The Quick Draw(R), Quick Draw 90(R), and Quick Draw(R) Flex feature: * Compact, lightweight design for portability and fast, easy one-person operation. * Develops 8 tons of hydraulic force for easy punching, even in 10-gauge stainless steel depending on individual punch capacities. * Quick Draw(R) is perfect for fast, straight-on front panel punching. * Quick Draw 90(R)'s right angle driver head rotates over 180 degrees for maximum flexibility in tight working areas. * Quick Draw(R) Flex allows unlimited driver orientation to simplify access to work area. * Can be used with non-round punches within the capacity of the tool (adapter may be required). WEIGHT LBS. kg. 12.1 5.5 17.3 7.9 10 4.5 14 6.4 9.4 4.3 10.3 4.7 11.4 5.2 10 4.5 14 6.4 11 5.0 11 5.0 12.2 5.5 See next page for complete parts list for all kits. STEEL CAPACITIES FOR CONDUIT SIZES STANDARD PUNCHES AND SLUG-BUSTERS(R) REQUIRED DRAW STUD AND ACCESSORIES 1/2" 3/4" 1-7/32" OILTIGHT 1" 1-1/4" 1-1/2" SLUG-SPLITTERS(R) 2" 1/2" 3/4" 1-7/32" OILTIGHT 1-1/4" 3/8" Draw Stud Spacer & 7/16" Draw Stud Adapter & 7/16" Draw Stud Spacer & 3/4" Draw Stud 3/4" Draw Stud 10 GA. MILD STEEL 14 GA. MILD STEEL 10 GA. STAINLESS STEEL 21 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Parts List for Quick Draw(R), Quick Draw 90(R) and Quick Draw(R) Flex Kits CONDUIT & PIPE 7704SB/ 7706SB/ 7804E/ 7804ESB/7804ISO/ 7804SB/ 7806SB/ 7904E/ 7904ESB/7904ISO/ 7904SB/ 7906SB/ 721-1/2 31756 1/2" Conduit Size Slug-Buster(R) Punch 1/2" 7/8 0.885 22.5 16 -- 14722 14722 1/2" Conduit Size Die 1/2" 7/8 0.885 22.5 16 -- 721-3/4 31757 3/4" Conduit Size Slug-Buster(R) Punch 3/4" -- 1.115 28.3 21 -- 124AV 06972 3/4" Conduit Size Die 3/4" -- 1.115 28.3 21 -- 721-1 31758 1" Conduit Size Slug-Buster(R) Punch 1" -- 1.362 34.6 -- -- 126AV 04011 1" Conduit Size Die 1" -- 1.362 34.6 -- -- 1-1/4" 1-11/16 1.701 43.2 -- -- 04013 1-1/4" Conduit Size Die 1-1/4" 1-11/16 1.701 43.2 -- -- 721-1-1/2 31760 1-1/2" Conduit Size Slug-Buster(R) Punch Punches and Dies ACTUAL UPC NO. DESCRIPTION 128AV Draw Studs and Misc. KIT CAT./UPC NO. CAT. NO. 721-1-1/4 31759 1-1/4" Conduit Size Slug-Buster(R) Punch SIZE HOLE SIZE O INCH O mm PG ISO 10475 10476 34291 35611 35614 34292 34299 35615 35616 33794 34300 1-1/2" 1-15/16 1.951 49.6 -- -- 440AV 04061 1-1/2" Conduit Size Die 1-1/2" 1-15/16 1.951 49.6 -- -- 721-2 31761 2" Conduit Size Slug-Buster(R) Punch 2" 2-3/8 2.416 61.5 -- -- 442AV 04063 2" Conduit Size Die 2" 2-3/8 2.416 61.5 -- -- 31969 31969 Slug-Buster(R) Punch -- -- 0.598 15.2 9 -- 32002 32002 Die -- -- 0.598 15.2 9 -- 31970 31970 Slug-Buster(R) Punch -- -- 0.732 18.6 11 -- 32003 32003 Die -- -- 0.732 18.6 11 -- 31971 31971 Slug-Buster(R) Punch -- -- 0.803 20.4 13 20 32004 32004 Die -- -- 0.803 20.4 13 20 721-1/2 31756 Slug-Buster(R) Punch 1/2" 7/8 0.885 22.5 16 -- 14722 14722 Die 1/2" 7/8 0.885 22.5 16 -- 31973 31973 Slug-Buster(R) Punch 3/4" -- 1.115 28.3 21 -- 32006 32006 Die 3/4" -- 36284 36284 30.5 mm Slug-Buster(R) Punch 1.115 28.3 21 -- -- 1-7/32 1.210 30.5 -- -- 1-7/32 1.210 30.5 -- -- 36279 36279 30.5 mm Die -- 35163 35163 ISO-16 Slug-Buster(R) Punch -- -- 0.638 16.2 -- 16 35162 35162 ISO-16 Die -- -- 0.638 16.2 -- 16 35165 35165 ISO-25 Slug-Buster(R) Punch -- 1 1.000 25.4 -- 25 35164 35164 ISO-25 Die -- 1 1.000 25.4 -- 25 35169 35169 ISO-32 Slug-Buster(R) Punch -- -- 1.280 32.5 -- 32 35168 35168 ISO-32 Die -- -- 1.280 32.5 -- 32 35158 35158 ISO-40 Slug-Buster(R) Punch -- -- 1.595 40.5 -- 40 35159 35159 ISO-40 Die -- -- 1.595 40.5 -- 40 34288 34288 Quick Draw(R) Hydraulic Punch Driver 33786 33786 Quick Draw 90(R) Hydraulic Punch Driver 10383 10383 Quick Draw(R) Flex Driver 1614SS 30043 Draw Stud-3/8" x 2-13/16" 31872 31872 Draw Stud-3/4" x 4-1/8" 1924AA 03248 Spacer-Short 33967 33967 Stud Adapter-3/8" 35202 35202 Plastic Case 34983 34983 Plastic Case 10391 10391 Plastic Case 29451 29451 7/16" (11.1 mm) Stainless Steel Draw Stud Optional Accessories for 7806SB, 7804E, 7804ESB, 7804ISO, 7906SB, 7904E, 7904ESB and 7904ISO Kits (not included in kits) 22 34293 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Slug-Buster(R) Ratchet Punch Driver Kits 1906SB WEIGHT LBS. kg. CAT. NO. UPC NO. DESCRIPTION 1904 Basic High Leverage Ratchet Driver with four draw studs and case 14 6.4 High Leverage Ratchet Driver with 1/2" through 2" Slug-Buster(R) conduit size punches, dies, draw studs and case 20 9.1 1906SB 30216 34357 Draw Studs and Misc. Punches and Dies HOLE SIZE CONDUIT & PIPE SIZE ACTUAL O INCH KIT CAT./UPC NO. CAPACITY MILD STEEL GA mm 1904/ 30216 1906SB/ 34357 CAT. NO. UPC NO. DESCRIPTION 721-1/2 31756 1/2" Conduit Size Slug-Buster(R) Punch 1/2" 7/8 0.885 22.5 10 3.5 14722 14722 1/2" Conduit Size Die 1/2" 7/8 0.885 22.5 10 3.5 721-3/4 31757 3/4" Conduit Size Slug-Buster(R) Punch 3/4" -- 1.115 28.3 10 3.5 124AV 06972 3/4" Conduit Size Die 3/4" -- 1.115 28.3 10 3.5 721-1 31758 1" Conduit Size Slug-Buster Punch 1" -- 1.362 34.6 10 3.5 126AV 04011 1" Conduit Size Die 1" -- 1.362 34.6 10 3.5 721-1-1/4 31759 1-1/4" Conduit Size Slug-Buster(R) Punch 1-1/4" 1-11/16 1.701 43.2 10 3.5 128AV 04013 1-1/4" Conduit Size Die 1-1/4" 1-11/16 1.701 43.2 10 3.5 721-1-1/2 31760 1-1/2" Conduit Size Slug-Buster Punch 1-1/2" 1-15/16 1.951 49.6 10 * 3.5 440AV 04061 1-1/2" Conduit Size Die 1-1/2" 1-15/16 1.951 49.6 10 * 3.5 721-2 31761 2" Conduit Size Slug-Buster(R) Punch 2" 2-3/8 2.416 61.5 10 * 3.5 442AV 04063 2" Conduit Size Die 2" 2-3/8 2.416 61.5 10 * 3.5 12097 12097 Draw Stud - 3/8" x 2-15/16" 12098 12098 Draw Stud - 3/4" x 3-15/16" 12099 12099 Draw Stud - 3/4" x 4-3/4" 30227 30227 Draw Stud - 7/16" x 3-5/8" 30228 30228 Steel Case 20495 20495 Ratchet wrench only 30225 30225 Handle (R) (R) O mm HOLEMAKING * Time saving ball bearing head punches faster than wrench method. * Requires less than half the force of conventional ratchet drivers. * Punches up through 10 gauge (3.5 mm) mild steel with Greenlee(R) Standard and Slug-Buster(R) punches; and 16 gauge (1.5 mm) stainless steel with Greenlee Slug-Splitter(R) punches. * Ratchet action allows for use in confined areas. * Unique design eliminates stud rotation during punching - lowers the strain on studs. * Steel carrying case. 23 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Standard Round Manual Knockout Punch Kits CAT. NO. UPC NO. DESCRIPTION 735BB 19973 1/2" - 1-1/4" Conduit Size Manual Round Standard Knockout Punch Kit 737BB 19974 1-1/2" - 2" Conduit Size Manual Round Standard Knockout Punch Kit 7304 02815 Standard punches and dies (no draw studs) for 2-1/2" through 4" conduit, in plastic case CAPACITY MILD STEEL WEIGHT GA mm LBS. kg. 10 3.5 2.5 1.1 10 3.5 4.4 2.0 10 3.5 21 9.5 735BB/19973 KNOCKOUT PUNCH KIT INCLUDES 737BB CAT. NO. 721-1/2 14722 00042 123AV 124AV 125AV 126AV 127AV 128AV 249AVBB 31880 Wrench Sold Separately 735BB UPC NO. 31756 14722 00042 04008 06972 04010 04011 06974 04013 04040 31880 HOLE SIZE ACTUAL O INCH O mm 7/8 0.885 22.5 7/8 0.885 22.5 DESCRIPTION 1/2" Conduit Size Slug-Buster(R) Punch 1/2" Conduit Size Die 3/8" x 1-9/16" Draw Stud 3/4" Conduit Size Punch -- 1.115 3/4" Conduit Size Die -- 1.115 1" Conduit Size Punch -- 1.362 1" Conduit Size Die -- 1.362 1-1/4" Conduit Size Punch 1-11/16 1.701 1-1/4" Conduit Size Die 1-11/16 1.701 3/4" x 2-1/8" Draw Stud Plastic Case 28.3 28.3 34.6 34.6 43.2 43.2 737BB/19974 KNOCKOUT PUNCH KIT INCLUDES 7304 CAT. NO. 439AV 440AV 441AV 442AV 304AVBB 32012 UPC NO. 06978 04061 04062 04063 04042 32012 DESCRIPTION 1-1/2" Conduit Size Punch 1-1/2" Conduit Size Die 2" Conduit Size Punch 2" Conduit Size Die 3/4" x 2-15/16" Draw Stud Plastic Case HOLE SIZE ACTUAL O INCH O mm 1-15/16 1.951 49.6 1-15/16 1.951 49.6 2-3/8 2.416 61.5 2-3/8 2.416 61.5 7304/02815 KNOCKOUT PUNCH KIT INCLUDES * Assortment of commonly used round standard knockout punches, packaged to meet the contractor's needs. * High-impact, rugged plastic carrying case. CAT. NO. 1429AV 1430AV 1431AV 1432AV 2982AV 2981AV 2984AV 2983AV 30236 UPC NO. 04175 04177 04180 04183 04978 04652 04655 04654 30236 DESCRIPTION 2-1/2" Conduit Size Punch 2-1/2" Conduit Size Die 3" Conduit Size Punch 3" Conduit Size Die 3-1/2" Conduit Size Punch 3-1/2" Conduit Size Die 4" Conduit Size Punch 4" Conduit Size Die Plastic Case HOLE SIZE ACTUAL O INCH O mm 2-7/8 2.914 74.0 2-7/8 2.914 74.0 3-1/2 3.539 89.9 3-1/2 3.539 89.9 4 4.044 102.7 4 4.044 102.7 4-1/2 4.544 115.4 4-1/2 4.544 115.4 NOTE: See Round Standard Knockout Punch Units on page 11 or 25 for list of individual punch units 24 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Standard Round Knockout Punches 0.885" to 2.416" Bushing Die See page 11 for other sizes of standard round punches Draw Stud SPECIFICATIONS Capacity Mild steel up through 10 gauge (3.5 mm). Application Punch mild steel, aluminum, fiberglass and plastic. Hole Sizes Conduit Sizes - Hole size is outside diameter of US conduit sizes. Example: 1/2" conduit size punch actually makes a 7/8" hole. Pg Sizes - European standard pipe sizes. ISO Sizes - International Standards Organization pipe sizes. Operation Operate manually or with battery-powered, hydraulic, or ratchet drivers. When used with battery-powered, hydraulic, or ratchet drivers buy the punch and die only; the draw stud is part of the driver kit. Punch Every cut quick and clean Slug falls free in die. ...Just tip it out. HOLEMAKING * Round Standard Metal Punch Units are complete units consisting of punch, die and draw stud. * Use with manual, battery-powered, hydraulic, or ratchet drivers. * Properly assembled through pilot holes, they will make clean, fast and accurate holes. Ball Bearing Nut Standard Round Knockout Punches PUNCH UNIT REPLACEMENT PARTS Every cut quick and clean PUNCH KIT-INCLUDES PUNCH, DIE & DRAW STUD CAT. NO. UPC NO. 71BB 72BB 36910 24476 73BB 730EBB-37 24477 74BB 730EBB-47 75BB 730BB-2 730BB-2-1/8 730EBB-60 76BB 22563 22564 36910 24476 22565 18890 24477 22566 18891 22567 20676 20678 18892 22568 CONDUIT & PIPE SIZE 1/2" 3/4" 3/4" -- 1" -- -- 1-1/4 -- 1-1/2" -- -- -- 2" Slug falls free in die. HOLE SIZE ACTUAL O INCH 7/8 -- -- -- -- -- -- 1-11/16 -- 1-15/16 2 2-1/8 -- 2-3/8 0.885 1.115 1.115 1.280 1.362 1.457 1.595 1.701 1.850 1.951 2.000 2.125 2.362 2.416 ...Just tip it out. O mm PG ISO 22.5 28.3 28.3 32.5 34.6 37.0 40.5 43.2 47.0 49.6 50.8 54.0 60.0 61.5 16 21 21 -- -- 29 -- -- -- -- -- 42 48 -- -- -- -- 32 -- -- 40 -- -- -- 50 -- -- -- CAPACITY MILD STEEL GA. mm 10 10 14 10 10 10 10 10 10 10 10 10 10 10 3.5 3.5 2.0 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 WEIGHT LBS. g REPLACEMENT PUNCH CAT. NO. UPC NO. REPLACEMENT DIE CAT. NO. UPC NO. .4 182 .9 409 .6 273 1 454 1.1 499 1 454 1.3 590 1.4 636 1.7 772 2 908 1.9 862 2.2 998 2.6 1180 3 1361 121AV 123AV 36882 24459 125AV 18331 24462 127AV 17687 439AV 1756AV 1783AV 17690 441AV 14722 124AV 32006 35168 126AV 32008 35159 128AV 32009 440AV 35161 36173 32011 442AV 04006 04008 36882 24459 04010 18331 24462 06974 17687 06978 04232 04245 17690 04062 14722 06972 32006 35168 04011 32008 35159 04013 32009 04061 35161 36173 32011 04063 REPLACEMENT DRAW STUD CAT. NO. UPC NO. 00042 249AVBB 00042 249AVBB 249AVBB 249AVBB 249AVBB 249AVBB 304AVBB 304AVBB 304AVBB 304AVBB 304AVBB 304AVBB 00042 04040 00042 04040 04040 04040 04040 04040 04042 04042 04042 04042 04042 04042 25 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Standard Round Manual Industrial Punch Kit HOLEMAKING * * * * Includes most popular sizes for industrial applications. Time-saving tool for maintenance, repair and operation applications. Convenient steel carrying case. Ball bearing drive screw for easy manual operation or use with ratchet and hydraulic drivers. CAT. NO. UPC NO. DESCRIPTION 39860 39860 3/4" - 1-1/2" Hole Size Manual Industrial Punch Kit 39860 MANUAL INDUSTRIAL KNOCKOUT PUNCH KIT INCLUDES Wrench Sold Separately SPECIFICATIONS Operation Manual - wrench not included. Capacity 1-1/4" Punch - 16 gauge (1.5 mm) mild steel. 3/4", 1" and 1-1/8" Punches - 14 gauge (2.0 mm) mild steel. 7/8" and 1-1/2" Punches 10 gauge (3.5 mm) mild steel. HOLE SIZE ACTUAL O INCH O mm CAT. NO. UPC NO. DESCRIPTION 113AV 114AV 03998 03999 3/4" Punch 3/4" Die 3/4 3/4 0.750 0.750 19.1 19.1 121AV 14722 04006 14722 7/8" Punch 7/8" Die 7/8 7/8 0.885 0.885 22.5 22.5 87AV 35164 03986 35164 1" Punch 1" Die 1 1 1.000 1.000 25.4 25.4 91AV 92AV 03990 03991 1-1/8" Punch 1-1/8" Die 1-1/8 1-1/8 1.125 1.125 28.6 28.6 117AV 118AV 04002 04003 1-1/4" Punch 1-1/4" Die 1-1/4 1-1/4 1.250 1.250 31.8 31.8 3207AV 3208AV 04736 07044 1-1/2" Punch 1-1/2" Die 1-1/2 1-1/2 1.500 1.500 38.1 38.1 00042 249AVBB 00042 04040 3/8" BB Draw Stud 3/4" BB Draw Stud 19193 19193 Steel Storage Box NOTE: See standard round Knockout Punch Units on page 11 or 25 for listing of individual punch units. 26 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Standard Round Manual Knockout Punch Kits - Metric SLUGBUSTER CAT. NO. UPC NO. CAT. NO. UPC NO. DESCRIPTION 36686 Punches and Dies Draw Studs and Misc. see page 13 36687 36687 see page 13 36688 36688 see page 13 36689 36689 see page 13 7309E 32804 Pg-9 through 30.5 mm Manual Round Standard Knockout Punch Kit Pg-9 through Pg-48 Manual Round Standard Knockout Punch Kit ISO-16 through ISO-40 Manual Round Standard Knockout Punch Kit ISO-16 through ISO-63 Manual Round Standard Knockout Punch Kit Pg-9 through Pg-48 Standard Knockout Pg. Punch Kit. Replacement Kit packaged in Carton without Plastic Case. 5.2 2.3 8.8 4 5.2 2.3 8.8 4 8.8 4 NOTE: See Slugbuster Knockout Punch Units on page 10 for list of individual punch units. SPECIFICATIONS Operation 36686 36686 WEIGHT LBS. kg. HOLEMAKING * 1" (25.4 mm) hex ratchet wrench allows use with both 3/8" (9.5 mm) and 3/4" (19.1 mm) draw studs. * 12.7 mm Kwik Stepper(R) step bit included. * Plastic carrying case Manual - Ratchet wrench included. CAT. NO. UPC NO. DESCRIPTION 21316 31969 32002 17700 32003 17697 32004 121AV 14722 36882 32006 36282 36279 18331 32008 17687 32009 17690 32011 35193 35162 87AV 35164 24459 35168 24462 35159 1756AV 35161 1758AV 1757AV 249AVBB 304AVBB 34941 34410 00042 36685 21316 31969 32002 17700 32003 17697 32004 04006 14722 36882 32006 36282 36279 18331 32008 17687 32009 17690 32011 35193 35162 03986 35164 24459 35168 24462 35159 04232 35161 04234 04233 04040 04042 34941 34410 00042 36685 HOLE SIZE ACTUAL O INCH O mm Pg-9 Punch -- 0.598 15.2 Pg-9 Slug-Buster(R) Punch -- 0.598 15.2 Pg-9 Die -- 0.598 15.2 Pg-11 Punch -- 0.732 18.6 -- 0.732 18.6 Pg-11 Die Pg-13 Punch -- 0.803 20.4 Pg-13 Die -- 0.803 20.4 Pg-16 Punch 7/8 0.885 22.5 Pg-16 Die 7/8 0.885 22.5 Pg-21 Punch -- 1.115 28.3 -- 1.115 28.3 Pg-21 Die 30.5 mm Punch 1-7/32 1.210 30.5 30.5 mm Die 1-7/32 1.210 30.5 Pg-29 Punch -- 1.457 37.0 Pg-29 Die -- 1.457 37.0 Pg-36 Punch -- 1.850 47.0 -- 1.850 47.0 Pg-36 Die Pg-48 Punch -- 2.362 60.0 Pg-48 Die -- 2.362 60.0 ISO-16 Punch -- 0.638 16.2 ISO-16 Die -- 0.638 16.2 ISO-25 Punch 1 1.000 25.4 ISO-25 Die 1 1.000 25.4 ISO-32 Punch -- 1.280 32.5 ISO-32 Die -- 1.280 32.5 ISO-40 Punch -- 1.595 40.5 ISO-40 Die -- 1.595 40.5 ISO-50 Punch 2 2.000 50.8 ISO-50 Die 2 2.000 50.8 ISO-63 Punch 2-1/2 2.500 63.5 ISO-63 Die 2-1/2 2.500 63.5 Draw Stud - 3/4" x 2-1/8" Draw Stud - 3/4" x 2-15/16" Ratchet wrench - 1" Hex Kwik Stepper(R) step bit 1/2" (12.7 mm) Ball Bearing Draw Stud with 1" Hex Head, 3/8" x 1-5/8" Plastic Case PG ISO 9 9 9 11 11 13 13 16 16 21 21 -- -- -- -- -- 20 20 29 29 36 36 48 48 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 16 16 25 25 32 32 40 40 50 50 63 63 -- -- CAPACITY MILD STEEL GA mm 36686 14 14 14 14 14 14 14 10 10 10 10 16 16 10 10 10 10 10 10 14 14 14 14 10 10 10 10 10 10 10 10 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.5 3.5 3.5 3.5 1.5 1.5 3.5 3.5 3.5 3.5 3.5 3.5 2.0 2.0 2.0 2.0 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 KIT CAT./UPC NO. 7309/E 36687 36688 36689 32804 27 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Ram and Hand Pump Hydraulic Driver Kits (Inch and Metric) * Fast, easy and simple to operate. * Compact design for field use on construction sites and maintenance jobs. * Punches 10 times faster than wrench method. * Will also drive 751 Cable Cutter head. * Can be used with all standard round, Slug-Buster(R) and Slug-Splitter(R) punches. * Can be used with non-round punches (adapter may be required). * 3-foot hose. * Powerful 11-ton hydraulic ram. 7646 SLUGBUSTER CAT. NO. UPC NO. CAT. NO. UPC NO. DESCRIPTION 7646 7306 15906 15909 see page 19 7310 15910 see page 19 7646Pg 27433 see page 19 7304 02815 38456 38456 WEIGHT LBS. kg. Driver with hand pump, plastic case 20 Driver, hand pump, standard punches, dies and draw studs for 1/2" through 2" conduit, plastic case 24 Driver, hand pump, standard punches, dies and draw studs for 1/2" through 4" conduit, steel case 54 Metric - Driver, hand pump, standard Pg punches, dies and draw studs for 15.2 mm through 60.0 mm, plastic case 24 Standard punch and die kit (no draw studs) for 2-1/2" through 4" conduit, plastic case 21 Driver, hand pump, standard punches, dies and draw studs for 1/2" through 3" and 4" conduit, steel case 48.4 see page 19 9.1 11 25 11 9.5 22 STEEL CAPACITIES FOR CONDUIT SIZES STANDARD & SLUG-BUSTER(R) PUNCHES REQUIRED DRAW STUD AND ACCESSORIES 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" STANDARD 2-1/2" 3" 3-1/2" SLUG-SPLITTERS(R) 4" 1/2" 3/4" 1" 1-1/4" 1-1/2" 2" 3/4" Stud (03294), 3/8" Stud (30043) & Spacers 3/4" Stud (03294), Long Spacer 3/4" Stud (03294), Short Spacer 3/4" Stud (03294) 3/4" Stud (03294), & Sleeve (03170) 7/16" Stud (29451) 3/4" Stud (29452) & Spacer 10 GA. MILD STEEL FF B HH G G LL K K AA JJ I RR M M N N 28 10 GA. STAINLESS STEEL RAM AND HAND PUMP HYDRAULIC DRIVER PARTS IDENTIFICATION KEY CAT./UPC NO. DESCRIPTION A 746 / 17091 Ram (includes Item B) B 2113AA / 03294 Draw Stud-3/4" x 5-3/8" F 1557AA / 03170 Punch Sleeve G 1614SS / 30043 Draw Stud-3/8" x 2-13/16" H 15908 Spacer Group (includes Items I, J and K) I 1924AA / 03248 Spacer-Short J 1925AA / 03249 Spacer-Medium K 1926AA / 06904 Spacer-Long L 34410 Kwik Stepper(R) Step Bit 1/2" M 767 / 13284 Hydraulic Hand Pump N 06302 / 06302 High Pressure Hose-1/4" x 3' R 30206 Plastic Case USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Ram and Hand Pump Kits Parts List Draw Studs and Misc. Punches & Dies CAT. NO. UPC NO. DESCRIPTION 1/2" 1/2" 1/2" 3/4" 3/4" 1" 1" 1-1/4" 1-1/4" 1-1/2" 1-1/2" 2" 2" ACTUAL O INCH KIT CAT./UPC NO. O mm PG 721-1/2 121AV 14722 123AV 124AV 125AV 126AV 127AV 128AV 439AV 440AV 441AV 442AV 31756 04006 14722 04008 06972 04010 04011 06974 04013 06978 04061 04062 04063 1/2" Conduit Size Slug-Buster(R) Punch 1/2" Conduit Size Punch 1/2" Conduit Size Die 3/4" Conduit Size Punch 3/4" Conduit Size Die 1" Conduit Size Punch 1" Conduit Size Die 1-1/4" Conduit Size Punch 1-1/4" Conduit Size Die 1-1/2" Conduit Size Punch 1-1/2" Conduit Size Die 2" Conduit Size Punch 2" Conduit Size Die 7/8 7/8 7/8 -- -- -- -- 1-11/16 1-11/16 1-15/16 1-15/16 2-3/8 2-3/8 0.885 0.885 0.885 1.115 1.115 1.362 1.362 1.701 1.701 1.951 1.951 2.416 2.416 22.5 22.5 22.5 28.3 28.3 34.6 34.6 43.2 43.2 49.6 49.6 61.5 61.5 16 16 16 21 21 -- -- -- -- -- -- -- -- 1429AV 1430AV 1431AV 1432AV 2982AV 2981AV 2984AV 2983AV 21316 32002 17700 32003 17697 32004 36882 32006 36282 36279 18331 32008 17687 32009 17690 32011 746 2113AA 1557AA 1614SS 15908 1924AA 1925AA 1926AA 34410 767 06302 30206 18402 04175 04177 04180 04183 04653 04652 04655 04654 21316 32002 17700 32003 17697 32004 36882 32006 36282 36279 18331 32008 17687 32009 17690 32011 17091 03294 03170 30043 15908 03248 03249 06904 34410 13284 06302 30206 18402 2-1/2" Conduit Size Punch 2-1/2" 2-7/8 2-1/2" Conduit Size Die 2-1/2" 2-7/8 3" Conduit Size Punch 3" 3-1/2 3" Conduit Size Die 3" 3-1/2 3-1/2" Conduit Size Punch 3-1/2" 4 3-1/2" Conduit Size Die 3-1/2" 4 4" Conduit Size Punch 4" 4-1/2 4" Conduit Size Die 4" 4-1/2 Punch -- -- Die -- -- Punch -- -- Die -- -- Punch -- -- Die -- -- Punch 3/4" -- Die 3/4" -- 30.5 mm Punch -- 1-7/32 30.5 mm Die -- 1-7/32 Punch -- -- Die -- -- Punch -- -- Die -- -- Punch -- -- Die -- -- Ram (includes following item) - Draw Stud-3/4" x 5-3/8" Punch Sleeve Draw Stud-3/8" x 2-13/16" Spacer Group (includes 1 ea. of the following 3 items) - Spacer-Short - Spacer-Medium - Spacer-Long Kwik Stepper(R) Step Bit 1/2" Hydraulic Hand Pump High Pressure Hose-1/4" x 3' Plastic Case Steel Case 2.914 2.914 3.539 3.539 4.044 4.044 4.544 4.544 0.598 0.598 0.732 0.732 0.803 0.803 1.115 1.115 1.210 1.210 1.457 1.457 1.850 1.850 2.362 2.362 74.0 74.0 89.9 89.9 102.7 102.7 115.4 115.4 15.2 15.2 18.6 18.6 20.4 20.4 28.3 28.3 30.5 30.5 37.0 37.0 47.0 47.0 60.0 60.0 -- -- -- -- -- -- -- -- 9 9 11 11 13 13 21 21 -- -- 29 29 36 36 48 48 7646/ 7306/ 7310/ 7646PG/ 15906 15909 15910 27433 38456 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 HOLEMAKING HOLE SIZE CONDUIT & PIPE SIZE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 See Slugbuster punch units on page 10 29 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Knockout Punch Parts Assortment Cabinets HOLEMAKING * Includes balanced stock of replacement parts in sturdy steel cabinets. UPC NO. DESCRIPTION 7360SB 34358 Knockout Punch Parts Assortment 1/2" - 2". Includes metal cabinet 14" high, 13" wide and 14-3/4" deep, with 4 drawers. 7361SB 34359 Knockout Punch Parts Assortment 1/2" - 3". Includes metal cabinet 19-1/2" high, 27" wide and 15" deep with 4 drawers. 7360SB 7361SB/34359 PARTS CABINET INCLUDES 7361SB 7360SB/34358 PARTS CABINET INCLUDES 30 CAT. NO. CAT. NO. UPC NO. DESCRIPTION 721-1/2 31756 Slug-Buster 1/2" Conduit Punch 18 14722 14722 1/2" Conduit Die 12 (R) QTY. 721-3/4 31757 Slug-Buster(R) 3/4" Conduit Punch 6 124AV 06972 3/4" Conduit Die 6 721-1 31758 Slug-Buster(R) 1" Conduit Punch 6 126AV 04011 1" Conduit Die 6 721-1-1/4 31759 Slug-Buster(R) 1-1/4" Conduit Punch 6 128AV 04013 1-1/4" Conduit Die 6 721-1-1/2 31760 Slug-Buster(R) 1-1/2" Conduit Punch 3 440AV 04061 1-1/2" Conduit Die 3 721-2 31761 Slug-Buster(R) 2" Conduit Punch 3 442AV 04063 2" Conduit Die 2 1429AV 04175 2-1/2" Conduit Punch 1 1430AV 04177 2-1/2" Conduit Die 1 1431AV 04180 3" Conduit Punch 1 1432AV 04183 3" Conduit Die 1 00042 00042 3/8" Draw Stud 12 249AVBB 04040 3/4" Drive Screw 8 CAT. NO. UPC NO. DESCRIPTION QTY. 304AVBB 04042 3/4" Drive Screw 6 721-1/2 31756 Slug-Buster(R) 1/2" Conduit Punch 18 1434AV 04188 1" x 3/4" Drive Screw 1 14722 14722 1/2" Conduit Die 12 1433AVBB 04187 1" Ball Bearing Nut 1 721-3/4 31757 Slug-Buster(R) 3/4" Conduit Punch 6 12097 12097 3/8" Adapter Screw 6 124AV 06972 3/4" Conduit Die 6 30227 30227 7/16" Adapter Screw 2 721-1 31758 Slug-Buster(R) 1" Conduit Punch 3 12098 12098 3/4" Adapter Screw 2 126AV 04011 1" Conduit Die 3 12099 12099 3/4" Ball Bearing Adapter Screw 1 721-1-1/4 31759 Slug-Buster(R) 1-1/4" Conduit Punch 3 1614SS 30043 3/8" Stainless Steel Adapter 20 128AV 04013 1-1/4" Conduit Die 3 2113AA 03294 3/4" Piston Shaft 6 721-1-1/2 31760 Slug-Buster(R) 1-1/2" Conduit Punch 2 1557AA 03170 1-1/8" Thread Sleeve 1 440AV 04061 1-1/2" Conduit Die 2 3037AV 04686 3-1/2", 4" & 5" Conduit Bushing 1 721-2 31761 Slug-Buster(R) 2" Conduit Punch 2 1924AA 03248 Short Spacer 3 442AV 04063 2" Conduit Die 1 1925AA 03249 Medium Spacer 3 00042 00042 3/8" Draw Stud 12 1926AA 06904 Long Spacer 3 249AVBB 04040 3/4" Drive Screw 4 15908 15908 Spacer Unit 1 304AVBB 04042 3/4" Drive Screw 4 28154 28154 Punch 1/2" HD Slug-Splitter(R) 1 12097 12097 3/8" Adapter Screw 4 28155 28155 Die 1/2" HD Slug-Splitter(R) 1 12098 12098 3/4" Adapter Screw 2 29451 29451 Draw Stud, 7/16" Stainless Steel 1 1614SS 30043 3/8" Stainless Steel Adapter 20 31834 31834 Cabinet A only (top) 1 2113AA 03294 3/4" Piston Shaft 4 31849 31849 Cabinet B only (bottom) 1 31832 31832 Cabinet only 1 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com 1731 Portable C-Frame Punch Drivers 1731 Fast, one-shot punching, no predrilling of pilot holes. Great for punching junction boxes and small enclosures. Punch can be used with ram inside or outside of the junction box. Throat measures 8" (203 mm) deep. For use with 1/2" - 1" (22.5 mm - 34.6 mm) conduit size and accessory sizes only. WEIGHT LBS. kg. CAT. NO. UPC NO. DESCRIPTION 1731 15911 Driver with ram, 1/2" through 1" conduit (22.5 mm through 34.6 mm) punches and dies 32 15 1731H767 20486 Same as 1731 with 767 hydraulic hand pump 36 17 1731F1725 25169 Same as 1731 with 1725 hydraulic foot pump 43 20 21316 21316 Pg-9 (15.2 mm) Punch (optional) 18557 18557 Pg-9 (15.2 mm) Die (optional) 17700 17700 Pg-11 (18.6 mm) Punch (optional) 18558 18558 Pg-11 (18.6 mm) Die (optional) 17697 17697 Pg-13 (20.4 mm) Punch (optional) 18559 18559 Pg-13 (20.4 mm) Die (optional) 36282 36282 1-7/32" (30.5 mm) Oil Tight Punch (optional) 37103 37103 1-7/32" (30.5 mm) Oil Tight Die (optional) HOLEMAKING * * * * * SPECIFICATIONS Capacity Up through 10 gauge (3.0 mm) mild steel with Greenlee special C-Frame dies and standard punches; 1/2" through 1" conduit and 15.2 mm through 30.5 mm. CAT. NO. UPC NO. DESCRIPTION HOLE SIZE KIT CAT./UPC NO. CONDUIT & PIPE 1731/ 1731H767/ 1731F1725/ SIZE PG O mm 15911 20486 25169 C-Frame with Ram 13276 13276 Punch Adapter-3/8"o x 1/2" (9.5 mmo) 13277 13277 Punch Adapter-3/4"o x 1" (19.0 mmo) 121AV 04006 1/2" Conduit Size Punch 1/2" 16 22.5 123AV 04008 3/4" Conduit Size Punch 3/4" 21 28.3 125AV 04010 1" Conduit Size Punch 1" -- 34.6 12087 12087 C-Frame 1/2" Conduit Size Die 1/2" 16 22.5 12086 12086 C-Frame 3/4" Conduit Size Die 3/4" 21 28.3 12085 12085 C-Frame 1" Conduit Size Die 1" -- 34.6 16634 16634 Steel Case 1725 25144 1725 Hydraulic Foot Pump 37729 37729 Hydraulic Hose-1/4" x 10' (3 m) 767 13284 Hydraulic Hand Pump 38316 38316 High Pressure Hose Unit-1/4" x 3' (includes 1 each of the following 3 items) 54169 54169 - 1/4" Male Coupler 54170 54170 - Dust Cap 06302 06302 - High Pressure Hose-1/4" x 3' 31 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com 1732 Portable C-Frame Punch Drivers HOLEMAKING * * * * Fast, one-shot punching, no predrilling of pilot holes. Use with 1/2" through 4" conduit size and other round sizes only. Use with Greenlee standard round punches and dies (optional). Throat measures 8" (203 mm) deep. CAT. NO. UPC NO. DESCRIPTION 1732 27361 Driver with ram, 3/8", 3/4" and 1-1/8" punch and die adapters 59 27 SPECIFICATIONS Capacity Up through 10 gauge (3.0 mm) mild steel with Greenlee Standard punches and dies; 1/2" through 4" conduit and 15.2 through 115.4 mm. CAT. NO. UPC NO. DESCRIPTION 1732 32 WEIGHT LBS. kg KIT CAT./UPC NO. 1732/ 1732H755/ 27361 27362 C-Frame with Ram 11791 11791 Die Adapter-3/8"o (9.5 mm) 11790 11790 Die Adapter-3/4"o (19.0 mm) 11789 11789 Die Adapter-1-1/8"o (28.6 mm) 13266 13266 Punch Adapter-3/8"o x 1/2" (9.5 mmo) 13267 13267 Punch Adapter-3/4"o x 1" (19.0 mmo) 13268 13268 Punch Adapter 1-1/8"o (28.6 mmo) 27335 27335 Metal Case 755 15677 Hydraulic Hand Pump 11289 11289 Hydraulic Hose-3/8" x 6' (9.5 mm x 1.8 m) 50642 50642 Nut-3/4"-10 (19.0 mm) USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Oiltight Punches with Notches B A C Counter Nut HOLE SIZE INCH B A C mm B A C Punch Draw Stud Die MAXIMUM CAT./UPC NO. CAPACITY PUNCH UNIT MILD STEEL OPERATION (INCLUDES PUNCH DRAW GA mm TYPE DIE AND DRAW STUD) PUNCH DIE STUD Ball Bearing Drive Nut OPTIONAL BB MINIMUM ADAPTER FOR DRIVE COUNTER PILOT HOLE O WEIGHT HYDRAULIC NUT NUT INCH mm LBS. kg. DRIVERS .875 .125 1.000 22.5 3.2 25.4 14 2.0 Hand/Hydr. 60238 60239 60250 60117 60165 60258 .625 15.9 2.1 .95 60167 1.210 .190 1.380 30.5 4.8 36.0 10 3.5 Hand/Hydr. 60242 60243 60249 60117 60165 60258 .625 15.9 2.7 1.2 60167 HOLEMAKING Other oiltight sizes without notches available in standard, Slug-Buster(R) and Slug Splitter(R) designs. For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers. Key Punches B C A Counter Nut HOLE SIZE A 0.481 O 1.171 O 1.265 O 1.328 O INCH B 0.055 0.123 0.156 0.102 mm B C A .030 .097 .097 .097 12.2 O 29.7 O 32.1 O 33.7 O 1.4 3.1 4.0 2.6 C .8 2.5 2.5 2.5 Die Punch Draw Stud Ball Bearing Drive Nut CAT./UPC NO. MAXIMUM PUNCH UNIT OPTIONAL CAPACITY (INCLUDES BB MINIMUM ADAPTER FOR MILD STEEL OPERATION PUNCH DIE DRAW DRIVE COUNTER PILOT HOLE O WEIGHT HYDRAULIC GA mm TYPE AND DRAW STUD) PUNCH DIE STUD NUT NUT INCH mm LBS. kg. DRIVERS 16 14 14 14 1.5 2.0 2.0 2.0 Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. 60101 60104 60107 60110 60102 60105 60108 60111 For use with any Greenlee Hydraulic Driver or Battery-Powered Driver 60103 60106 60109 60112 60115 60166 60166 60166 60120 60165 60165 60165 05244 60258 60258 60258 .375 .875 .875 .875 9.5 23.8 23.8 23.8 .88 .4 2.3 1.0 2.4 1.1 2.4 1.1 60114 60167 60167 60167 For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers 720 Keyway Punch * Eliminates time consuming hand sawing and filing when making keyways for push button switches. * Use as a nibbler to make wider or deeper keyways. * Punches 1/8" (3.2 mm) or 3/16" (4.8 mm) keyways for 7/8" (22.5 mm) or 1-7/32" (30.5 mm) push button holes. * Patented - U.S. Patent No. 4,375,128; Canadian Patent No. 1,172,435. 3/16" (4.7mm) 720 1/8" (3.2mm) CAT. NO. UPC NO. DESCRIPTION WEIGHT LBS. kg. 720 26534 2.8 1.27 Keyway Punch SPECIFICATIONS Operation Capacity Manual 10 gauge (3.5 mm) mild steel. Cutting Notch 3/16" Key 3/16" 1/8" Deep Punch Die 3/32" Deep Cutting Notch 1/8" Key 1/8" 1. Locate proper cutting notch on the cutting head. 2. Place cutting notch inside edge of hole and cut keyway. 3. Withdraw the punch. 4. Use as a nibbler to make wider or deeper keyways. 33 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING "D" Punches A B Counter Nut Punch Ball Bearing Drive Nut Draw Stud Die CAT./UPC NO. A MAXIMUM PUNCH UNIT CAPACITY (INCLUDES MILD STEEL OPERATION PUNCH, DIE GA mm TYPE AND DRAW STUD) HOLE SIZE INCH mm B A B 0.500 O 0.625 O 0.750 O 0.469 0.594 0.703 12.7 O 15.9 O 19.1 O 11.9 15.1 17.9 16 14 14 2.0 2.0 2.0 Hand/Hydr. Hand/Hydr. Hand/Hydr. 60077 60080 60083 For use with any Greenlee Hydraulic Driver or Battery-Powered Driver PUNCH DIE 60078 60079 60081 60082 60084 60085 DRAW STUD BB DRIVE NUT 60115 60113 60113 60120 34733 34733 OPTIONAL MINIMUM ADAPTER FOR COUNTER PILOT HOLE O WEIGHT HYDRAULIC NUT INCH mm LBS. kg. DRIVERS 05244 04638 04638 .375 .500 .500 9.5 .9 .41 12.7 1.1 .50 12.7 1.2 .50 60114 33967 33967 For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers Double "D" Punches B A Counter Nut Punch Die Draw Stud Ball Bearing Drive Nut CAT./UPC NO. HOLE SIZE INCH mm A B A B 0.769 O 0.795 O 0.913 O 0.913 O 1.375 O 0.642 0.697 0.756 0.795 1.125 19.5 O 20.2 O 23.2 O 23.2 O 34.9 O 16.3 17.6 19.2 20.2 28.6 MAXIMUM CAPACITY MILD STEEL GA mm OPERATION TYPE 14 14 14 14 14 Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. 2.0 2.0 2.0 2.0 2.0 PUNCH UNIT (INCLUDES PUNCH, DIE AND DRAW STUD) PUNCH 60086 60089 60092 60095 60098 For use with any Greenlee Hydraulic Driver or Battery-Powered Driver 60087 60090 60093 60096 60099 DIE DRAW STUD OPTIONAL BB MINIMUM ADAPTER FOR DRIVE COUNTER PILOT HOLE O WEIGHT HYDRAULIC NUT NUT INCH mm LBS. kg. DRIVERS 60088 60091 60094 60097 60100 60113 60113 60113 60113 60166 34733 34733 34733 34733 60165 04638 04638 04638 04638 60258 .500 .500 .500 .500 .875 12.7 12.7 12.7 12.7 23.8 1.1 1.1 1.2 2 2.5 .50 .50 .54 .9 1.1 33967 33967 33967 33967 60167 For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers Square and Special Square Punches A B Square Counter Nut Special Square Punch Draw Stud Die Ball Bearing Drive Nut CAT./UPC NO. HOLE SIZE INCH mm MAXIMUM PUNCH UNIT CAPACITY (INCLUDES MILD STEEL OPERATION PUNCH, DIE GA mm TYPE AND DRAW STUD) PUNCH DIE DRAW STUD BB DRIVE NUT OPTIONAL MINIMUM ADAPTER FOR COUNTER PILOT HOLE O WEIGHT HYDRAULIC NUT INCH mm LBS. kg DRIVERS 1/2" 0.500 x 0.500 12.7 x 12.7 16 1.5 Hand/Hydr. 60001 60002 60003 60115 60120 05244 .375 9.5 1.1 .50 60114 5/8" 0.625 x 0.625 15.9 x 15.9 14 2.0 Hand/Hydr. 60004 60005 60006 60116 34733 04638 .500 12.7 1.5 .68 33967 3/4" 0.750 x 0.750 19.1 x 19.1 14 2.0 Hand/Hydr. 60007 60008 60009 60116 34733 04638 .500 12.7 1.5 .68 33967 7/8" 0.882 x 0.882 22.4 x 22.4 14 2.0 Hand/Hydr. 60259 60011 60012 60116 34733 04638 .500 12.7 1.8 .82 33967 0.945 x 0.945 24.0 x 24.0 14 2.0 Hand/Hydr. 60013 60014 60015 60116 34733 04638 .500 12.7 2.3 1.0 33967 1" 1.000 x 1.000 25.4 x 25.4 14 2.0 Hand/Hydr. 60016 60017 60018 60117 60165 60258 .625 15.9 2.4 1.1 60167 60235 1.188 30.2 6.0 2.7 60235 1.188 30.2 6.2 2.8 60235 1.188 30.2 6.9 3.1 60235 1.188 30.2 10.1 4.6 60235 1.188 30.2 14.8 6.7 * 60235 1.188 30.2 18.8 8.5 * 60235 1.188 30.2 20 9.1 * 04638 .500 12.7 .7 .3 33967 1.772 x 1.772 45.0 x 45.0 10 3.5 Hydr. Only 60287 60288 60289 60118 1-13/16" 1.811 x 1.811 46.0 x 46.0 10 3.5 Hydr. Only 60019 60020 60021 60118 2.000 x 2.000 50.8 x 50.8 10 3.5 Hydr. Only 60168 60169 60170 60118 2-11/16" 2.677 x 2.677 68.0 x 68.0 10 3.5 Hydr. Only 60171 60172 60173 60118 3-5/8" 3.622 x 3.622 92.0 x 92.0 10 3.5 *Hydr. Only 60174 60175 60176 60118 4-1/8" 4.125 x 4.125 104.8 x 104.8 10 3.5 *Hydr. Only 60177 60178 60179 60118 5.433 x 5.433 138.0 x 138.0 14 2.0 *Hydr. Only 60234 60023 60024 60118 -- -- -- -- -- -- -- 22.5 O(A) 20.1(B) 14 2.0 Hand/Hydr. 60125 60126 60127 60116 34733 2" SPECIAL SQUARE 0.886(A) 34 0.791(B) *For use with with Hand and Foot Pump Hydraulic Drivers with Ram For use with any Greenlee Hydraulic Driver, or Battery-Powered Driver For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Rectangular Punches Die Draw Stud Ball Bearing Drive Nut CAT./UPC NO. MAXIMUM CAPACITY MILD STEEL OPERATION GA mm TYPE HOLE SIZE INCH mm 0.437 x 0.875 0.670 x 0.749 0.750 x 1.140 0.750 x 1.310 0.861 x 1.018 0.866 x 1.181 0.866 x 1.654 0.990 x 1.140 1.250 x 1.380 1.312 x 2.625 1.378 x 2.047 1.378 x 2.559 1.378 x 3.228 1.378 x 4.409 1.811 x 3.622 2.250 x 3.500 2.677 x 5.433 11.1 x 22.2 17.0 x 19.0 19.1 x 29.0 19.1 x 33.3 21.9 x 25.9 22.0 x 30.0 22.0 x 42.0 25.1 x 29.0 31.8 x 35.1 33.3 x 66.7 35.0 x 52.0 35.0 x 65.0 35.0 x 82.0 35.0 x 112.0 46.0 x 92.0 57.2 x 88.9 68.0 x 138.0 16 14 14 14 14 14 14 14 14 10 10 10 14 14 10 10 14 1.5 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.5 3.5 3.5 2.0 2.0 3.5 3.5 2.0 PUNCH UNIT (INCLUDES PUNCH, DIE AND DRAW STUD) PUNCH DIE DRAW STUD 60025 60028 60031 60034 60037 60040 60043 60047 60050 60053 60056 60059 60062 60065 60068 60071 60074 60026 60029 60032 60035 60038 60041 60045 60048 60051 60054 60057 60060 60063 60066 60069 60072 60075 60027 60030 60033 60036 60039 60042 60046 60049 60052 60055 60058 60061 60064 60067 60070 60073 60076 60115 60116 60117 60117 60117 60117 60117 60117 60117 60118 60118 60118 60118 60118 60118 60118 60118 Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hand/Hydr. Hydr. Only Hydr. Only Hydr. Only *Hydr. Only *Hydr. Only *Hydr. Only *Hydr. Only *Hydr. Only *For use with with Hand and Foot Pump Hydraulic Drivers with Ram For use with any Greenlee Hydraulic Driver or Battery-Powered Driver BB MINIMUM DRIVE COUNTER PILOT HOLE O NUT NUT INCH mm 60120 34733 60165 60165 60165 60165 60165 60165 60165 -- -- -- -- -- -- -- -- 05244 04638 60258 60258 60258 60258 60258 60258 60258 60235 60235 60235 60235 60235 60235 60235 60235 .375 .500 .625 .625 .625 .625 .625 .625 .625 1.188 1.188 1.188 1.188 1.188 1.188 1.188 1.188 9.5 12.7 15.9 15.9 15.9 15.9 15.9 15.9 15.9 30.2 30.2 30.2 30.2 30.2 30.2 30.2 30.2 WEIGHT LBS. kg 1.2 1.5 2.3 2.3 2.3 2.4 2.9 2.6 3.1 5.1 6.1 6.8 7.7 9.2 8.9 10.1 16.1 OPTIONAL ADAPTER FOR HYDRAULIC DRIVERS .5 .68 1.0 1.0 1.0 1.1 1.3 1.2 1.4 2.3 2.8 3.1 3.5 4.2 4.0 4.6 7.3 HOLEMAKING Punch Counter Nut 60114 33967 60167 60167 60167 60167 60167 60167 60167 * * * * * For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers Electronic Connector Panel Punches * Cut-out and mounting slots are punched in one operation. * Drill only one 7/16" (11.1 mm) pilot hole. (See catalog page 63 for Kwik Stepper(R) step bits.) * Fast, accurate panel punching with no sawing or filing required. * Universal size punches for front or back mount of TRW Cinch and ITT Cannon-type or equivalent connectors in 9, 15, 25, 37 or 50-pin configurations. * U.S. Patent No. 4,899,447. 9 PIN 229 15 PIN 230 25 PIN RS232 SPECIFICATIONS 37 PIN 234 1.6 mm (1/16") R. A 50 PIN 238 10 Operation Manual with a wrench; Quick Draw(R) and Quick Draw 90(R) hydraulic drivers, Battery Driver, Ram and Pump hydraulic drivers. C Capacity 16 gauge (1.5 mm) mild steel; 10 gauge (3.5 mm) aluminum. B PUNCH UNIT CAT. NO. DIMENSIONS NO. OF UPC NO. PINS A B C PUNCH REPLACEMENT CAT./UPC NO. SQUARE DIE UNIT DRAW STUD COUNTER NUT WEIGHT DRIVE NUT LBS. kg. 229 34436 9 .787" (20.0 mm) .982" (24.9 mm) .469" (11.9 mm) 34441 35196 34421 04638 34733 1.4 .64 231 34437 15 1.127" (28.6 mm) 1.309" (33.3 mm) .469" (11.9 mm) 34442 35197 34421 04638 34733 1.5 .68 RS232 34420 25 1.655" (42.0 mm) 1.853" (47.1 mm) .469" (11.9 mm) 34418 35198 34421 04638 34733 2.0 .91 234 34429 37 2.296" (58.3 mm) 2.497" (63.4 mm) .469" (11.9 mm) 34427 35199 34421 04638 34733 2.0 .91 238 34444 50 2.201" (55.9 mm) 2.402" (61.0 mm) .579" (14.7 mm) 34443 35200 34421 04638 34733 2.0 .91 For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers 35 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Replacement Draw Studs for Manual Drivers HOLEMAKING Replacement Draw Stud Selection Guide If you need to replace a broken draw stud, refer to the full scale pictures and information below when ordering a replacement draw stud. Sizes given diameter x length. 304AVBB / 04042 - 3/4" (19.0 mm) x 2-15/16" (75 mm) 00042 - 3/8" (9.5 mm) x 1-5/8" (41 mm) 249AVBB / 04040 - 3/4" (19.0 mm) x 2-1/8" (54 mm) 1675AV Draw Stud / 04218 - 1/4" (6.4 mm) x 1-3/8" (35 mm) 36 3026AV / 04679 - 1-1/8" (28.6 mm) x 7-1/2" (190 mm) 1434AV / 04188 - 3/4" (19.0 mm) x 5-1/2" (140 mm) USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Replacement Draw Studs for Hydraulic Drivers 1614SS / 30043 - 3/8" (9.5 mm) x 2-13/16" (71 mm) HOLEMAKING Replacement Draw Stud Selection Guide If you need to replace a broken draw stud, refer to the full scale pictures and information below when ordering a replacement draw stud. Sizes given diameter x length. 1557AA / 03170 - 1-1/8" (28.6 mm) x 3" (76 mm) 33967 (Adapter) - 3/4" (19 mm) x 1-7/8" (48 mm) 29451 - 7/16" (11.1 mm) x 4-1/4" (108 mm) 2113AA / 03294 - 3/4" (19.0 mm) x 5-3/8" (137 mm) 29452 - 3/4" (19.0 mm) x 5-1/2" (140 mm) Replacement Draw Studs for Ratchet Drivers 12099 - 3/4" (19.0 mm) x 4-3/4" (121 mm) 30227 - 7/16" (11.1 mm) x 3-5/8" (92 mm) 12097 - 3/8" (9.5 mm) x 3-1/2" (89 mm) 37 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 HOLEMAKING Replacement Draw Studs for Special Shape Punches Replacement Draw Stud Selection Guide If you need to replace a broken draw stud, refer to the full scale pictures and information below when ordering a replacement draw stud. Sizes given diameter x length. For maximum draw stud life, Greenlee recommends the use of battery or hydraulic drivers. 60166 - 1/2" (12.7 mm) x 4-5/8" (117.5 mm) 60117 - 1/2" (12.7 mm) x 4-5/8" (117.5 mm) 60113 - 3/8" (9.5 mm) x 3-11/16" (93.7 mm) 60116 - 3/8" (9.5 mm) x 3-3/4" (95.3 mm) 34421 - 3/8" (9.5 mm) x 3-1/2" (88.9 mm) 60115 - 1/4" (6.3 mm) x 3-7/16" (87.3 mm) 38 60118 - 3/4" (19 mm) x 6-3/4" (171.5 mm) greenlee.com USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Structural Stud Punch HOLEMAKING * Punch 16 and 18 gauge structural studs in 5 seconds. * Punch 200 holes per battery charge, 2 batteries included eliminating downtime * Punches a 1.34 (34.1 mm) diameter hole in 16 (1.5 mm) guage steel. For use with Greenlee 712A bushings. * Swivel head rotates 360 for use in tight corners. * Pistol grip handle gives better leverage and reduces fatigue. * Replacement punch and die. * Lightweight 9.2 lb. tool provides heavy-duty performance. BATTERY-POWERED STUD PUNCH ACTUAL HOLE SIZE CAT. NO. UPC NO. ESP710-11 ESP710-12 ESP710-22 WEIGHT LENGTH HEIGHT CAPACITY IN. mm LBS. kg IN. mm IN. mm GA mm BATTERY CHARGER 10307 1-11/32 34.1 9.2 4.2 15 381 11-3/4 298 16 1.5 12V2.0 Ah NiCd 120 Volt 10308 1-11/32 34.1 9.2 4.2 15 381 11-3/4 298 16 1.5 12V2.0 Ah NiCd 12 Volt 10309 1-11/32 34.1 9.2 4.2 15 381 11-3/4 298 16 1.5 12V2.0 Ah NiCd 230 Volt Plumber Stud Punch * Punches 2-5/8" (66.7 mm) diameter hole in metal studs for professional looking installation of 2" water, vent, waste pipes. * Two-speed lever action for fast, easy punching of 24 to 20 gauge thick metal studs. * 2-1/8" (54 mm) throat width fits over most studs and channels. * High strength alloy aluminum c-frame and handle provides lightweight tool for easy handling-10.6 lb. (4.8 kg). * Lever action punch retraction strips punch out of metal stud fast and easy. PLUMBER STUD PUNCH ACTUAL HOLE SIZE CAT. NO. UPC NO. 713 06430 WEIGHT LENGTH HEIGHT CAPACITY IN. mm LBS. kg IN. mm IN. mm GA mm 2-5/8 66.7 10.6 4.8 23-1/2 596 9-3/4 247 24-20 0.9 39 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Metal Stud Punches HOLEMAKING * Punch up through 20 gauge (0.9 mm) steel studs in one stroke. * Aluminum head provides strength with minimum weight, reducing operator fatigue. * Contoured handle design gives better operator leverage and makes it possible to punch in tight places. * Self-stripping design eliminates punch hang-ups. * Automatically centers holes on standard studs. * Conversion kit available to upgrade early models from 24 gauge to 20 gauge maximum capacity. SPECIFICATIONS Capacity 709 - 1-5/8" (41.3 mm) and wider studs. 20 gauge (0.9 mm) steel studs. 710 - 2-1/2" (63.4 mm) and wider studs. 20 gauge (0.9 mm) steel studs. WEIGHT LBS. kg CAT. NO. UPC NO. DESCRIPTION 709 22280 7/8" (22.2 mm) Diameter Stud Punch 7 3.2 710 21285 1-11/32" (34.1 mm) Diameter Stud Punch 7.5 3.5 30968 30968 Conversion Kit - Upgrades early model 709 or 710 from 24 to 20 gauge maximum capacity 121AV 04006 Punch for 709 - Accessory 22286 22286 Die for 709 - Accessory 24823 24823 Punch for 710 - Accessory 21297 21297 Die for 710 - Accessory Manual Stud Punches * Punch up through 20 gauge (0.9 mm) steel studs in one stroke. * Unique patented punch rolls the edge over for smooth installation of armored cable; cable won't hang up. * Contoured handle design gives better operator leverage and makes it possible to punch in tight places. * Automatically centers holes on standard studs. * Conversion kit available to upgrade early models from 24 gauge to 20 gauge maximum capacity. * 724BX, armored cable stud punch, primary use is the steel studs within the perimeter of the building. MANUAL STUD PUNCH ACTUAL HOLE SIZE CAT. NO. UPC NO. 724 10415 WEIGHT LENGTH HEIGHT CAPACITY IN. mm LBS. kg IN. mm IN. mm GA mm 1-1/4 31.7 4.0 1.8 16-3/4 426 4-1/2 114 24-20 0.9 Bushings for Metal Stud Punches (R) R 40 * Triple lock design holds bushing securely. * Locks securely into metal studs from 24 gauge to 12 gauge (0.6 mm to 2.5 mm). * Helps protect wire insulation from sharp edges of metal studs. * Makes pulling smooth and easy by preventing hang-ups of cable on raw metal edges. CAT. NO. UPC NO. DESCRIPTION 711C 22288 711M 22289 712A100 05927 712A1000 05928 WEIGHT LBS. kg 100 Bushings for hole punched by 709 for 7/8" (22.2 mm) diameter hole .5 1,000 Bushings for hole punched by 709 for 7/8" (22.2 mm) diameter hole 3.7 100 Bushings for pre-punched hole or 1-11/32" (34.1 mm) diameter hole punched by 710 1.4 1,000 Bushings for pre-punched hole or 1-11/32" (34.1 mm) diameter hole punched by 710 15.5 .23 1.7 .64 7.0 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Kwik Stepper Step Bits 03607 SPECIFICATIONS Hole Sizes From 1/8" through 1-3/8" (3.2 - 34.9 mm) Capacity Cut up through 3/8" (9.5 mm) mild steel, copper, brass, aluminum, wood, plastic and laminates. CAT. NO. 35884 03607 UPC NO. 35884 03607 DESCRIPTION Kwik Stepper(R) Step Bit Kit Kwik Stepper(R) Step Bit Kit CAT. NO. 34401 34403 30008 35936 UPC NO. 34401 34403 30008 35936 DESCRIPTION 1/2" Multi-Hole Step Bit 7/8" Multi-Hole Step Bit 1-1/8" Multi-Hole Step Bit Plastic Case SIZE INCHES 1/8 5/32" 3/16" 7/32" 1/4" 9/32" 5/16" 11/32" 3/8" 0.382" 13/32" 7/16" 15/32" 0.492" 1/2" 9/16" 0.598" 5/8" 0.638" 11/16" 0.732" 3/4" 0.803" 13/16" 7/8" 0.886" 1.00" 1.114" 1-1/8" 1.201" 1-7/32" 1-1/4" 1.280" 1-3/8" Overall Length mm 3.2 4.0 4.8 5.6 6.4 7.1 7.9 8.7 9.5 9.7 10.3 11.1 11.9 12.5 12.7 14.3 15.2 15.9 16.2 17.5 18.6 19.1 20.4 20.6 22.2 22.5 25.4 28.3 28.6 30.5 31.0 31.8 32.5 34.9 Minimum Chuck Size Maximum Material Thickness Bit Extension * 35884 * * * * METRIC Single-hole bits are designed to drill one indicated hole size through a series of steps from bit tip to full size. Multi-hole bits allow you to drill a hole in any of the stated diameters. 03607 * * HOLEMAKING * Unique split tip design penetrates through steel faster. * Resists walking or skidding, even on round surfaces. * Balanced, double-flute construction requires less pressure, does the work for you. * Designed and manufactured in USA. 35884 1/2" (12.7 mm) Single-Hole Step Bit 1/2" (12.7 mm) Multi-Hole Step Bit 1/2" (12.7 mm) Multi-Hole Step Bit 13/16" (20.6 mm) Multi-Hole Step Bit 34410 34401 36402 30005 7/8" (22.2 mm) Single-Hole Step Bit 7/8" (22.2 mm) Multi-Hole Step Bit CAT./UPC NO. 34411 34403 1-1/8" Electrician's Step Bit 1-3/8" (34.9 mm) Single-Hole Step Bit 9.7 mm (.382") Multi-Hole Step Bit 30.5 mm (1.201") Multi-Hole Step Bit 32.5 mm (1.280") 30008 36414 36018 36020 36022 Pg-7 Pg-9 ISO-16 Pg-11 Pg-13 ISO-20 Pg-16 ISO-25 Pg-21 ISO-32 1-5/8" (41.4 mm) 1/4" (6.4 mm) 10 gauge (3.5 mm) 901 3-1/8" (79.4 mm) 1/4" (6.4 mm) 10 gauge (3.5 mm) 901 3-3/16" (81.0 mm) 1/4" (6.4 mm) 3/8" (9.5 mm) 901 3-3/16" (81.0 mm) 1/4" (6.4 mm) 10 gauge (3.5 mm) 901 2-3/16" (55.6 mm) 3/8" (9.5 mm) 10 gauge (3.5 mm) -- 3-5/16" 2-1/4" (84.1 mm) (57.2 mm) 3/8" 3/8" (9.5 mm) (9.5 mm) 10 gauge 10 gauge (3.5 mm) (3.5 mm) -- -- 2-7/8" (73.0 mm) 3/8" (9.5 mm) 10 gauge (3.5 mm) -- 1.590" (40.4 mm) 1/4" (6.4 mm) 10 gauge (3.5 mm) 901 3-1/2" (88.9 mm) 3/8" (9.5 mm) 1/4" (6.4 mm) -- 3.100" (78.7 mm) 3/8" (9.5 mm) 1/4" (6.4 mm) -- 41 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Kwik ChangeTM Stainless Steel Hole Cutters INDIVIDUAL CARBIDE-TIPPED HOLE CUTTERS CAT. NO. SIZE CONDUIT UPC NO. INCH mm SIZE PG 645-5/8 05691 15.8 3/8 9.5 645-11/16 05692 11/16 17.5 3/8 9.5 3/8 9.5 3/8 9.5 645-3/4 05693 5/8 KIT CAT. KIT CAT. MIN. NO. 660/ NO. 655/ CHUCK SIZE UPC NO. UPC NO. ISO INCH mm 05766 05820 19.0 11 645-13/16 05694 13/16 20.6 3/4 13 645-7/8 05695 7/8 22.2 645-1 05696 1 25.4 20 1/2" 25 645-1-1/16 05957 1-1/16 27.0 645-1-1/8 05697 1-1/8 28.6 3/4" 21 645-1-7/32 05698 1-7/32 31.0 660 645-1-1/4 05699 1-1/4 31.8 645-1-5/16 05958 1-5/16 33.3 645-1-3/8 05700 1-3/8 34.9 32 1" 645-1-7/16 05959 1-7/16 36.5 * Cuts stainless steel quickly and easily. * Kwik ChangeTM arbor allows you to change cutter heads with a simple push and a turn. Use the same arbor for different size cutting heads. * Removable cutter heads available in sizes from 5/8" through 3". * Flange stop prevents over-drilling. * Ejector Spring on all sizes above 3/4" makes removal of slug easier. * Replaceable, cobalt-steel pilot drill with split-point tip to prevent walking. * Precision carbide teeth for optimum performance and durability. * Minimum chuck size of 3/8" KITS CAT. NO. 42 27 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 3/8 9.5 645-1-1/2 05701 1-1/2 38.1 3/8 9.5 645-1-3/4 05702 1-3/4 44.4 1-1/4" 3/8 9.5 645-2 05703 3/8 9.5 645-2-1/8 05960 2-1/8 54.0 2 50.8 1-1/2" 42 3/8 9.5 645-2-1/4 05704 2-1/4 57.2 48 3/8 9.5 645-2-3/8 05961 2-3/8 60.3 3/8 9.5 645-2-1/2 05705 2-1/2 63.5 3/8 9.5 645-2-5/8 05706 2-5/8 66.7 3/8 9.5 645-3 05707 3/8 9.5 3 2" 50 63 76.2 ARBORS AND PILOT DRILLS CAT. NO. UPC NO. DESCRIPTION 645-011 05752 Kwik ChangeTM Arbor for sizes 5/8" through 2-1/4" 645-022 05753 Kwik ChangeTM Arbor for sizes 2-3/8" through 3" UPC NO. DESCRIPTION 660 05766 7/8", 1-1/8", 1-3/8", 1-3/4", 2" cutter heads; arbor, hex key and case 645-001 05761 Pilot Drill for sizes 5/8" through 2-1/4" 655 05820 7/8", 1-1/8", 1-3/8" cutter heads; arbor, hex key and case 645-002 05762 Pilot Drill for sizes 2-3/8" through 3" KIT CAT. NO. 660/ UPC NO. 05766 KIT CAT. NO. 655/ UPC NO. 05820 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Carbide-Tipped Hole Cutters KIT CAT. NO. 635 UPC NO. 03599 DESCRIPTION 7/8", 1-1/8", 1-3/8" cutterheads; pilot drill, hex key and case WEIGHT LBS. kg 1.2 HOLEMAKING * Multiple tungsten carbide tips for long life and smooth cutting. * Cut fast, accurate, high quality holes in stainless steel, copper, aluminum, steel. * Flange stop prevents over drilling. * Replaceable cobalt steel pilot drill, with split point tip design, to improve performance and resist walking; eliminates need for "center punch." .54 CARBIDE-TIPPED HOLE CUTTERS CAT. NO. MIN. SIZE CONDUIT CHUCK SIZE UPC NO. INCH mm SIZE PG ISO INCH mm WEIGHT LBS. g 625-3/4 38324 625-13/16 38325 SPECIFICATIONS 3/4-2 2-1/2 PILOT DRILL CAT. NO. UPC NO. 19.0-50.8 625-001 63.5 Point of Purchase Package 38326 7/8 22.2 625-1 38327 1 25.4 625-002 1-1/8 28.6 1/2" 11 1/4 6.4 .02 13 20 1/4 6.4 .02 9 16 1/4 6.4 .33 150 3/8 9.5 .02 9 25 3/4" 21 625-1-7/32 38329 1-7/32 30.5 REPLACEMENT PILOT DRILLS CUTTER SIZE RANGE INCH mm 19.0 625-7/8 625-1-1/8 38328 Maximum Cutting Depth 8 Ga. (4 mm) 3/4 13/16 20.6 HEX SET SCREW WT. SIZE CAT./UPC NO. LBS. g 625-1-1/4 38330 1-1/4 31.7 625-1-3/8 38331 1-3/8 35.0 625-1-1/2 38332 1-1/2 38.1 625-1-3/4 38333 1-3/4 44.4 1-1/4" 39872 3 mm 54274 .19 86 625-2 38334 38390 4 mm 54295 .28 127 625-2-1/2 38336 2 1" 50.8 1-1/2" 2-1/2 63.5 2" 50 KIT CAT. NO. 635/ UPC NO. 03599 9 3/8 9.5 .43 195 3/8 9.5 .44 200 3/8 9.5 .33 150 3/8 9.5 .47 213 3/8 9.5 .37 168 3/8 9.5 .40 182 3/8 9.5 .50 227 1/2 12.7 .67 304 All hole cutters are packaged in Point of Purchase blister pack. 43 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com High-Speed Steel Cutters* Lasts 10 times longer than standard hole saws. Precision-ground teeth cut smooth, burr-free holes with ease. Durability and speed provide low cost per hole. Split-point pilot drill prevents "walking" - makes accurate hole placement easy. * Spring-loaded slug ejector saves time. * No tool required to change cutter sizes. * Less chance of broken teeth because the saw body is machined out of solid, high-speed steel. HOLEMAKING * * * * HIGH-SPEED STEEL CUTTERS ACTUAL HOLE SIZE CAT. NO. UPC NO. IN. mm 925-7/8 10157 925-1-1/8 CONDUIT HOLE DIAMETER PG ISO 7/8 22.5 1/2" Pg-16 10158 1-1/8 28.6 3/4" Pg-21 925-1-7/32 10643 1-7/32 30.5 925-1-3/8 10159 1-3/8 35.0 1" 925-1-3/4 10160 1-3/4 44.4 1-1/4" 925-2 10161 2 50.8 1-1/2" 925-2-1/2 10162 2-1/2 63.5 KIT CAT. NO. 930 COPPER PIPE 5/8" 1-1/2" ISO-50 ISO-63 2" UPC NO. DESCRIPTION 10214 High-Speed Steel Cutter Kit: Includes 7/8" to 2-1/2" cutters, two small arbors for extended assembly to 7/8" and 1-1/2" cutters, large arbor, hex wrench, case. For conduit sizes 1/2" through 2". ARBORS AND PILOT DRILLS CAT. NO. UPC NO. DESCRIPTION 925-011 10163 Small Arbor with pilot drill 925-022 10185 Large Arbor with pilot drill 925-001 10186 Small Pilot Drill 925-002 10211 Large Pilot Drill RECOMMENDED CUTTING SPEEDS 44 * Cutters made from high-speed steel. Follow recommended cutting speeds. CUTTER SIZE RPM 7/8" (22.5 mm) 350 1-1/8" (28.6 mm) 270 1-3/8" (35.0 mm) 220 1-3/4" (44.4 mm) 175 2" (50.8 mm) 150 2-1/2 (63.5 mm) 120 HOLE SAW TYPE AVERAGE CUTTING TIME (SEC/HOLE) AVERAGE NUMBER OF HOLES AVERAGE COST/HOLE ($) Bi-Metal 25 50 0.1 High-Speed Cutter 10 500 0.1 Carbide-Tipped Cutter 10 500 0.2 *For 7/8" Hole in 14ga Mild Steel USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Bi-Metal Hole Saws CAT. NO. 825-9/16 825-5/8 825-11/16 825-3/4 825-13/16 825-7/8 825-15/16 825-1 825-1-1/16 825-1-1/8 825-1-3/16 825-1-1/4 825-1-5/16 825-1-3/8 825-1-7/16 825-1-1/2 825-1-9/16 825-1-5/8 825-1-11/16 825-1-3/4 825-1-13/16 825-1-7/8 825-2 825-2-1/16 825-2-1/8 825-2-1/4 825-2-5/16 825-2-3/8 825-2-1/2 825-2-9/16 825-2-5/8 825-2-3/4 825-2-7/8 825-3 825-3-1/8 825-3-1/4 825-3-3/8 825-3-1/2 825-3-5/8 825-3-3/4 825-3-7/8 825-4 825-4-1/8 825-4-1/4 825-4-3/8 825-4-1/2 825-4-3/4 825-5 825-5-1/2 825-6 UPC NO. UPC NO. UPC NO. ACTUAL HOLE SIZE HOLE DIA. STANDARD PACK BULK PACK POINT OF PURCHASE INCH mm CONDUIT PG 19131 19132 19133 19134 19135 19136 19137 19138 19140 19141 19143 19144 19145 19146 19147 19148 19149 19150 19151 19152 19153 19154 19155 19157 19158 19159 19160 19161 19162 19163 19164 19165 19166 19167 19168 19169 19170 19171 19172 19174 19175 19176 19177 19178 19179 19180 19181 19182 19183 19184 29828 29829 29831 29832 29834 29835 29836 29837 29838 -- -- -- 00140 -- 38495 -- -- -- 38496 -- -- -- 38497 -- -- -- -- -- 38498 -- -- 38500 -- -- -- -- -- 38502 -- -- -- -- 00141 -- -- -- -- 00142 -- -- -- 00143 -- -- 00144 -- -- -- -- 9/16 5/8 11/16 3/4 13/16 7/8 15/16 1 1-1/16 1-1/8 1-3/16 1-1/4 1-5/16 1-3/8 1-7/16 1-1/2 1-9/16 1-5/8 1-11/16 1-3/4 1-13/16 1-7/8 2 2-1/16 2-1/8 2-1/4 2-5/16 2-3/8 2-1/2 2-9/16 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/4 3-3/8 3-1/2 3-5/8 3-3/4 3-7/8 4 4-1/8 4-1/4 4-3/8 4-1/2 4-3/4 5 5-1/2 6 14.3 15.9 17.5 19.0 20.6 22.2 23.8 25.4 27.0 28.6 30.2 31.7 33.3 35.0 36.5 38.1 39.7 41.3 42.9 44.4 46.0 47.6 50.8 52.4 54.0 57.2 58.7 60.3 63.5 65.0 66.7 69.8 73.0 76.2 79.4 82.5 85.7 88.9 92.1 95.2 98.4 101.6 104.8 108.0 111.1 114.3 120.6 127.0 139.7 152.4 ISO Pg-9 ISO-16 1/2" Pg-11 Pg-13 Pg-16 ISO-20 ISO-25 3/4" Pg-21 COPPER PIPE SIZE 1/8" 1/4" 3/8" 1/2" 1/2" 5/8" USE WITH ARBOR NO. 37157, 37155, or 38522 3/4" 3/4" 1" ISO-32 1" Pg-29 1-1/4" 37156 or 37154 ISO-40 1-1/4" 1-1/2" Pg-36 1-1/2" ISO-50 Pg-42 2" Pg-48 2" ISO-63 2" 2" 37156 2-1/2" 2-1/2" 3" 3-1/2" 3-1/2" 3-1/2" 4" 4" 5" 37156 HOLEMAKING * Cut through steel, tin, aluminum, fiberglass, wood and plastic. * Deep 1-5/8" (41.3 mm) cutting depth allows for cutting through 2" x 4" wood studs. * Extra-tough M42 alloy blade - we use the highest grade of tool steel to outlast competitor's blades. That beats premature saw replacement and saves you money. * Steam oxide finish - no paint to gum up and slow cutting. The saw runs cooler for longer life and better performance. * Extra-thick backplate minimizes vibration for smoother, easier, less-tiring cutting. * Made in USA. WEIGHT LBS. g .1 .1 .1 .1 .1 .1 .1 .1 .1 .1 .2 .2 .2 .1 .2 .2 .2 .2 .3 .2 .2 .3 .2 .3 .3 .3 .5 .3 .3 .4 .4 .4 .4 .5 .5 .6 .6 .6 .6 .7 .7 .7 .8 .8 .8 .9 1.1 1.2 1.2 1.4 46 46 46 46 46 46 46 46 46 46 91 91 91 46 91 91 91 91 137 91 91 137 91 137 137 137 227 137 137 182 182 182 182 227 227 273 273 273 273 318 318 318 363 363 363 409 499 545 545 636 45 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Carbide-Grit Hole Saws HOLEMAKING * Long-lasting tungsten carbide-grit delivers extremely clean, smooth cuts through tile, cement board, and other abrasive materials. Perfect for cutting holes in Quazite(R)* enclosure or hardy board siding for 3-0 box installation. * Rugged construction for enduring performance. * Use with Arbors listed below. CARBIDE GRIT HOLE SAWS PILOT DRILL CAT. NO. 725-001 UPC NO. 10082 DESCRIPTION 1/4" Carbide Tipped Pilot Drill ACTUAL HOLE SIZE INCH mm 7/8 22.2 1-1/8 28.6 CAT. NO. 725-7/8 725-1-1/8 UPC NO. 10072 10073 725-1-3/8 725-1-1/2 725-1-3/4 725-2 10075 10076 10077 10078 1-3/8 1-1/2 1-3/4 2 35.0 38.1 44.4 50.8 725-2-1/8 10079 2-1/8 54.0 725-2-1/2 10080 2-1/2 725-3-5/8 10081 3-5/8 725-4-1/8 10687 725-4-1/2 01879 HOLE DIAMETER CONDUIT PG ISO 1/2" 16 3/4" 21 1" 1-1/4" 1-1/2" 50 63.5 2" 63 92.1 3" 4-1/8 104.8 3-1/2" 4-1/2 114.3 4" Arbors With Replacement High Speed Steel Pilot Drill Bits * * * * * The best arbor in the industry ensures a solid connection without any gaps or wobbling. Arbors include replaceable high speed pilot drill. Pilot drills have unique split point tip design. Use with Greenlee bimetal hole saws, recessed light hole saws, and carbide grit hole saws (carbide tipped pilot drill sold separately). Can be used with Greenlee #901, #902 and #904 bit extensions. HIGH SPEED PILOT DRILLS ARBORS Cat./UPC No. Standard Pack Point of Purchase Pack Bulk Pack Cat./UPC No. 37157 38507 37157B 38522 38524 38522B Shank Round with 3 flats Hex Shank Size 1/4" (6.4 mm) 5/16" (7.9 mm) Min. Chuck Size 1/4" (6.4 mm) 3/8" (9.5 mm) Use With 9/16" - 1-3/16" 9/16" - 1-3/16" (14.3 - 30.2 mm) (14.3 - 30.2 mm) Hole Saws Hole Saws 46 Weight .2 lbs (91 g) * Quazite is a registered trademark of Strongwell Corporation. .2 lbs (91 g) 37155 38505 37155B 37154 38504 37154B 37156 38506 37156B Hex Hex Hex 7/16" (11.1 mm) 5/16" (7.9 mm) 7/16" (11.1 mm) 1/2" (12.7 mm) 3/8" (9.5 mm) 1/2" (12.7 mm) 9/16" - 1-3/16" 1-1/4" - 2" 1-1/4" - 6" (14.3 - 30.2 mm) (31.8 - 50.8 mm) (31.8 - 152.4 mm) Hole Saws Hole Saws Hole Saws and all Greenlee Recessed Light Hole Saws .2 lbs (91 g) .5 lbs (227 g) .5 lbs. (227 g) Standard Pack 37623 38526 Point of Purchase Pack 39873 39893 Bulk Pack Qty: 50 per pack Length Diameter Use With Greenlee Arbor #'s Weight 37624 38991 4-1/8" (104.8 mm) 3-1/4" (82.5 mm) 1/4" (6.4 mm) 1/4" (6.4 mm) 37157, 37155, 38522, 37155, 37156 & 37156 & 37154 37154 .2 lbs (91 g) .2 lbs (91 g) USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Bi-Metal Hole Saw Kits 835 / 27538 834 / 19913 830 / 19192 889 / 03478 CAT. NO. 830 834 835 830Pg 889 UPC NO. 19192 19913 27538 29209 03478 890 03479 891 03480 CAT. NO. UPC NO. DESCRIPTION 825-3/4 825-7/8 825-1 825-1-1/8 825-1-3/8 825-1-1/2 825-1-3/4 825-2 825-2-1/4 825-2-1/2 825-3 825-3-1/4 825-3-5/8 825-3-3/4 825-4-1/8 825-4-1/2 825-4-3/4 825-5/8 825-3/4 825-13/16 825-1-3/16 825-1-1/2 825-1-7/8 825-2-3/8 38522 37157 37155 37156 38526 19134 19136 19138 19141 19146 19148 19152 19155 19159 19162 19167 19169 19172 19174 19177 19180 19181 19132 19134 19135 19143 19148 19154 19161 38522 37157 37155 37156 38526 890 / 03479 DESCRIPTION Hole Saw Kit for 1/2" through 2" conduit sizes Hole Saw Kit for 2-1/2" through 4" conduit sizes Hole Saw Kit for 1/2" through 4" conduit sizes Hole Saw Kit for Pg-9 through Pg-48 Plumbers Hole Saw Kit - 3/4" through 2-1/4" conduit sizes Industrial Maintenance Hole Saw Kit - 3/4" through 4-3/4" conduit sizes Electrician's/Plumbers Hole Saw Kit - 3/4" through 2-1/2" conduit sizes 3/4" Hole Saw 7/8" Hole Saw 1" Hole Saw 1-1/8" Hole Saw 1-3/8" Hole Saw 1-1/2" Hole Saw 1-3/4" Hole Saw 2" Hole Saw 2-1/4" Hole Saw 2-1/2" Hole Saw 3" Hole Saw 3-1/4" Hole Saw 3-5/8" Hole Saw 3-3/4" Hole Saw 4-1/8" Hole Saw 4-1/2" Hole Saw 4-3/4" Hole Saw Pg-9 (15.9 mm) Hole Saw Pg-11 (19.0 mm) Hole Saw Pg-13 (20.6 mm) Hole Saw 30.2 mm Hole Saw Pg-29 (38.1 mm) Hole Saw Pg-36 (47.6 mm) Hole Saw Pg-48 (60.3 mm) Hole Saw Arbor w/pilot drill Arbor w/pilot drill Arbor w/pilot drill Arbor w/pilot drill Pilot Drill WEIGHT LBS. kg 2.7 1.2 6.2 2.8 7.7 3.5 2.7 1.2 2.3 1.0 9.7 4.4 3.5 1.6 HOLEMAKING * Several electrician's kits available providing an assortment of the most commonly used Greenlee variable pitch hole saw sizes and arbors. * High-impact, rugged plastic carrying case. KIT CAT./UPC NO. 830/ 834/ 835/ 830PG/ 889/ 890/ 891/ 19192 19913 27538 29209 03478 03479 03480 (2) 891 / 03480 47 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Recommended Hole Saw Cutting Speeds RPM HOLE SAW SIZE INCH mm 9/16 14.3 MILD STEEL 580 CAST IRON 400 RPM HOLE SAW SIZE INCH mm 2-5/16 58.7 BRASS ALUMINUM 790 900 5/8 15.9 550 365 730 825 11/16 17.5 500 330 665 3/4 19.0 460 300 600 13/16 20.6 425 280 7/8 22.2 390 260 MILD STEEL 150 CAST IRON 100 BRASS ALUMINUM 195 225 2-3/8 60.3 140 95 190 200 750 2-1/2 63.5 135 90 180 205 690 2-9/16 65.0 130 85 175 200 560 635 2-5/8 66.7 130 85 170 195 520 585 2.677 68.0 125 80 160 185 15/16 23.8 370 245 495 555 2-3/4 69.8 125 80 160 185 1 25.4 350 235 470 525 2-7/8 73.0 120 80 160 180 1-1/16 27.0 325 215 435 480 2.913 74.0 115 75 150 170 1-1/8 28.6 300 200 400 450 3 76.2 115 75 150 170 1-3/16 30.2 285 190 380 425 3-1/8 79.4 110 70 140 165 1-1/4 31.7 275 180 360 410 3-1/4 82.5 105 70 140 155 1-5/16 33.3 260 175 345 390 3-3/8 85.7 100 65 130 150 1-3/8 35.0 250 165 330 375 3-1/2 88.9 95 65 130 145 1-7/16 36.5 240 160 315 360 3-5/8 92.1 95 60 120 140 1-1/2 38.1 230 150 300 345 3-3/4 95.2 90 60 120 135 1-9/16 39.7 220 145 290 330 3-7/8 98.4 90 60 120 135 1-5/8 41.3 210 140 280 315 4 101.6 85 55 110 130 1-11/16 42.9 205 135 270 305 4-1/8 104.8 80 55 110 120 1-3/4 44.4 195 130 260 295 4-1/4 108.0 80 55 110 120 1-13/16 46.0 190 125 250 285 4-3/8 111.1 80 50 100 120 1-7/8 47.6 180 120 240 270 4-1/2 114.3 75 50 100 105 2 50.8 170 115 230 255 4-3/4 120.6 75 50 95 95 2-1/16 52.4 165 110 220 245 5 127.0 65 45 90 90 2-1/8 54.0 160 105 210 240 5-1/2 139.7 60 35 85 85 2-1/4 57.2 150 100 200 225 6 152.4 55 35 75 75 Flex Splitter(R) BX and Flexible Conduit Cutter * Cut flexible metal conduit in seconds with a few turns of the crank and an easy twist of the conduit. * Ample clearance between handle and body for comfortable operation. * Set conduit size for multiple cuts of the same size conduit. No need to reset. * Compact and lightweight. Fits easily in back pocket or tool pouch. * Set blade adjustment with only a screwdriver. * Convenient in-handle blade storage - holds up to five spare blades. * Point-of-purchase packaged. Blades point-of-purchase packaged 1 and 5 blades per package. SPECIFICATIONS 48 Capacity 14/2 to 10/4 BX 3/8" flexible metal conduit Weight 1940 - 4 lbs. (1.8 kg) CAT. NO. UPC NO. DESCRIPTION 1940 34953 Flex Splitter(R) Flexible Metal Conduit Cutter 1941-1 00288 Single Blade Replacement Blade for 1940 1941-5 33735 5 Pack Replacement Blades for 1940 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Reciprocating Blades Progressive-pitch reciprocating saw blades cut a wide rage of standard construction materials quickly and cleanly - regardless of thickness. Bimetal construction provides maximum flexibility and break resistance - plus lasting sharpness. Exclusive plunge tip makes starting cuts faster and easier. Blades color coded by application. 16-gauge metal stud EMT conduit strut thick wall pipe HOLEMAKING * * * * rod/rebar RECIPROCATING SAW BLADES Metal Wood Demolition Specialty Variety LENGTH x WIDTH x THICKNESS TEETH CAT. NO. UPC NO. INCHES mm PER INCH 353-123 09963 6 x 3/4 x .035 152 x 19.05 x .889 Progressive 353-318 09961 4 x 5/16 x .035 101 x 7.938 x .889 18 353-418 09962 4 x 3/4 x .035 101 x 19.05 x .889 18 353-614 09964 6 x 3/4 x .035 152 x 19.05 x .889 14 353-618 09965 6 x 3/4 x .035 152 x 19.05 x .889 18 353-624 09966 6 x 3/4 x .035 152 x 19.05 x .889 24 353-804 09977 8 x 3/4 x .050 203 x 19.05 x 1.27 10/14 353-814 09975 8 x 3/4 x .050 203 x 19.05 x 1.27 14 353-818 09976 8 x 3/4 x .050 203 x 19.05 x 1.27 18 353-234 09991 8 x 3/4 x .050 203 x 19.05 x 1.27 Progressive 353-656 09967 6 x 3/4 x .050 152 x 19.05 x 1.27 6 353-676 09971 6 x 3/4 x .050 152 x 19.05 x 1.27 6 353-646 09968 6 x 3.4 x .050 152 x 19.05 x 1.27 6 353-956 09969 9 x 3/4 x .050 228 x 19.05 x 1.27 6 353-156 09970 12 x 3/4 x .050 304 x 19.05 x 1.2 6 353-666 09978 6 x 7/8 x .062 152 x 22.23 x 1.56 6 353-966 09979 9 x 7/8 x .062 228 x 22.23 x 1.56 6 353-669 09980 6 x 7/8 x .062 152 x 22.23 x 1.56 8/10 353-969 09990 9 x 7/8 x .062 228 x 22.23 x 1.56 8/10 353-345 09972 8 x 3/4 x .050 203 x 19.05 x 1.27 Progressive 353-636 09973 6 x 3/4 x .050 152 x 19.05 x 1.27 6 353-800 09974 8 x 3/4 x .050 203 x 19.05 x 1.27 Grit 353-VAR 09992 6 x 3/4 x .035 152 x 19.05 x .889 Progressive 8 x 3/4 x .050 203 x 19.05 x 1.27 Progressive 8 x 3/4 x .050 203 x 19.05 x 1.27 Progressive TYPE Bimetal, Straight Bimetal, Scroll Bimetal, Straight Bimetal, Straight Bimetal, Straight Bimetal, Straight Bimetal, Straight Bimetal, Straight Bimetal, Straight HCS, Taper Bimetal, Taper Bimetal, Scroll Bimetal, Straight Bimetal, Straight Bimetal, Straight Bimetal, Taper Bimetal, Taper Bimetal, Taper Bimetal, Taper Bimetal, Taper Bimetal, Taper Carbide, Straight 353-123 353-234 353-345 APPLICATION Metal QTY. PER PK. 5 Metal 5 Metal 5 Metal 5 Metal 5 Metal 5 Metal 2 Metal 2 Metal 2 Wood Only 5 Wood with Nails 5 Wood with Nails 5 Wood with Nails 5 Wood with Nails 5 Wood with Nails 5 Wood Demolition 2 Wood Demolition 2 Metal Demolition 2 Metal Demolition 2 General 5 Plaster 5 Abrasive Materials Metal Wood Only General 2 1 1 1 49 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Jig Saw Blades * Progressive-tooth design delivers faster cutting through a broad range of material types and thicknesses. * Shatterproof bi-metal construction with high speed cobalt matrix cutting edge. * For rough and finish cutting in full range of applications including wood (even with nails), metal, plaster, drywall and fiberglass. * Tungsten Carbide Grit Edge blade style. -No teeth to snag, cuts efficiently on both up and down strokes for extra smooth finishes. -Additional cutting application for cast iron, tile, pipe, ceramic. * Center front tooth makes plunge cuts quick and easy. JIG SAW BLADES CAT. NO. 373-U123 373-U234 373-U345 373-U300 373-UVAR 373-T123 373-T234 373-T345 373-TVAR UPC NO. 09994 09993 09995 09996 09997 DESCRIPTION 3-5/8" Univeral Jig Saw Blade 4-1/4" Universal Jig Saw Blade 5" Universal Jig Saw Blade 2-3/4" Universal Jig Saw Blade Universal Jig Saw Blade - Variety Pack TEETH Progressive Progressive Progressive Grit Progressive 10004 10003 10005 10006 4" T-Shank Jig Saw Blade 4-1/2" T-Shank Jig Saw Blade 5-1/4" T-Shank Jig Saw Blade T-Shank Jig Saw Blade - Variety Pack Progressive Progressive Progressive Progressive TYPE High-speed Steel High-carbon Steet Bimetal Carbide Grit 373-U123 373-U234 373-U345 High-speed Steel High-carbon Steel Bimetal 373-T123 373-T234 373-T345 APPLICATION Metal Wood General Abrasive Materials Metal, Wood and General Metal Wood General Metal, Wood and General QTY. PER PK. 5 3 5 2 1 3 5 5 1 12" Hack Saw Tubular back provides handy blade storage inside. Heavy-duty die-cast aluminum handle is virtually break-proof. Large, 4-1/2" throat enables deeper cuts, makes handling easy. Convenient adjustment lever makes blade tensioning a snap. Bimetal blade design for long cutting life and flexibility. CAT. NO. UPC NO. DESCRIPTION 302 10047 12" (305 mm) Hack Saw Frame CAT. NO. UPC NO. DESCRIPTION 333 25571 12" (305 mm) Heavy Duty Hack Saw Frame 333-1218 10037 12" (305 mm) Bimetal Blade, 18 teeth per inch 5 333-1224 10038 12" (305 mm) Bimetal Blade, 24 teeth per inch 5 333-1232 10039 12" (305 mm) Bimetal Blade, 32 teeth per inch 5 REPLACEMENT HACK SAW BLADES SPECIFICATIONS 50 Capacity 12" (304.8 mm) Blade Weight 1.4 lbs. (0.7 kg) QTY. PER PK. USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com PVC Saws CAT. NO. 322113 322114 322115 322116 UPC NO. 00113 00114 00115 00116 BLADE LENGTH 13" (330 mm) 18" (457 mm) 13" (330 mm) 18" (457 mm) DESCRIPTION PVC Saw PVC Saw Replacement Blade for 00113 Replacement Blade for 00114 HOLEMAKING * "V" tooth design enables straight cuts on both push and pull saw strokes. * Resharpenable blade * Pointed blade nose makes drywall surface penetration easy. * Ergonomic handle is interchangeable with most popular PVC saw brands. Heavy-Duty Band Saw * Cuts up to 8" pipe and 9-1/2" x 11" (241 x 280 mm) tray or duct. * Convertible to wet cutting systems with optional accessories. * Three sawing speeds 76, 141, and 268 feet per minute (23, 43, and 82 meters per minute). * Converts to vertical in seconds. * Automatic shut-off after cut is complete. * Sturdy wheels for mobility and stability. * Heavy-duty, adjustable hydraulic feed. * Heavy-duty, steel bed with welded steel legs. SPECIFICATIONS Capacity CAT. NO. UPC NO. DESCRIPTION 1399 31961 1399-22 32364 9-1/2" x 11" capacity Mobile Band Saw (241.3 x 279.4 mm) 9-1/2" x 11" capacity Mobile Band Saw (241.3 x 279.4 mm) 220 VAC Wet Cutting System Vertical Work Table 32322 32237 32322 32237 Rectangular 9-1/2" x 11" (241.3 x 279.4 mm) Round 9-1/2" Dia. or 8" Pipe (241.3 mm) 45 Angle 5-1/2" x 5-1/2" (139.7 x 139.7 mm) Vertical Work Table 7-5/8" x 10" (193.7 x 254.0 mm) Throat Height 9-1/2" (241.3 mm) Throat Depth 6-1/4" (158.8 mm) Dimensions 52" h. x 47" l. x 27" w. (13208 h. x 11938 l. x 685.8 w. mm) Power Source 1399 -120 VAC 1/2 Horsepower. 1399-22 - 220 VAC Weight 346 lbs. (157 kg) Blade Size 1/2" x .025" x 93" (12.7 mm x 0.64 mm x 2362 mm) Band Saw Blades Perfect for your mobile or portable band saw, these top-quality, bimetal blades feature high-speed steel teeth that can handle even tough metals like stainless steel with ease. Virtually unbreakable, too. * Bimetal blades feature high-speed tool steel, bonded to an extra-tough alloy back for maximum hardness and heat resistance. * Fits most popular models of portable band saws. MOBILE BAND SAW BLADES CAT. NO. UPC NO. DESCRIPTION TYPE APPLICATION TEETH PER INCH QTY. PER PK. 399-14A 399-18A 399-24A 389-1014 389-1418 389-24 32336 32337 32338 10044 10045 10043 1/2" x .025" x 93" Mobile Band Saw Blade 1/2" x .025" x 93" Mobile Band Saw Blade 1/2" x .025" x 93" Mobile Band Saw Blade 1/2 x .020 x 44-7/8 Portable Band Saw Blade 1/2 x .020 x 44-7/8 Portable Band Saw Blade 1/2 x .020 x 44-7/8 Portable Band Saw Blade Bimetal Bimetal Bimetal Bimetal Bimetal Bimetal Metal Metal Metal Metal Metal Metal 10.14 18 24 10/14 14/18 24 3 3 3 3 3 3 51 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Nail Eater II(R) Wood Boring Bits 61PTS SHORTY, 62PTS AND 61/62 PTS BIG SHANK SHORTY NAIL EATER II(R) BITS POP BULK HOLE DIA. HEX SHANK WEIGHT CAT. NO. UPC NO. UPC NO. INCH mm INCH mm LBS. g 61PTS-5/8 30419 -- 5/8 15.9 5/16 7.9 .3 137 61PTS-3/4 30423 -- 3/4 19.1 5/16 7.9 .4 182 61PTS-7/8 30427 -- 7/8 22.2 5/16 7.9 .5 227 61PTS-1 30429 -- 1 25.4 5/16 7.9 .8 363 62PTS-5/8 31788 -- 5/8 15.9 7/16 11.1 .3 137 62PTS-11/16 31790 -- 11/16 17.5 7/16 11.1 .4 182 62PTS-3/4 31792 36640 3/4 19.1 7/16 11.1 .5 227 62PTS-13/16 31794 -- 13/16 20.6 7/16 11.1 .5 227 62PTS-7/8 31796 36642 7/8 22.2 7/16 11.1 .6 273 62PTS-1 31798 36643 1 25.4 7/16 11.1 .7 318 61/62PTS-1-1/8 30431 -- 1-1/8 28.6 7/16 11.1 .9 409 61/62PTS-1-1/4 30433 -- 1-1/4 31.8 7/16 11.1 1.1 499 * Patented new design for improved cutting and cleaner holes. * Self-feeding screw point draws bit through wood. * Unique patented design cutting angle - smoother starts, reduced cutting loads. * Made of super tough heat treated steel; cuts through nails and provides longer life. * "Shorty" bits - for working in tight places, yet still can go through three abutting 2 x 4s. * See "Bit Extensions" if more length is required (see page 68). * P.O.P. packaged. 66PT NAIL EATER II(R) BITS POP CAT. NO. UPC NO. 66PT-1/2 30915 66PT-5/8 30919 66PT-11/16 30921 66PT-3/4 30923 66PT-13/16 30925 66PT-7/8 30927 66PT-15/16 30929 66PT-1 30931 66PT-1-1/8 30935 66PT-1-1/4 30937 SPECIFICATIONS 61 PTS SHORTY NAIL EATER II(R) AND 62 PTS AND 61/62 BIG SHANK SHORTY NAIL EATER II(R) BITS Overall Length 7-5/8" (193.7 mm) Twist Length 5" (127 mm) Electric drill required 61 PTS - 5/8" through 61 PTS - 1", minimum 3/8" drill; All Big Shank, 1/2" drill. 66 PT NAIL EATER II(R) Overall Length 18" (457.2 mm) Twist Length 15" (381 mm) BULK UPC NO. -- -- -- 36659 -- 36662 -- 36664 -- -- HOLE DIA. INCH mm 1/2 12.7 5/8 15.9 11/16 17.5 3/4 19.1 13/16 20.6 7/8 22.2 15/16 23.8 1 25.4 1-1/8 28.6 1-1/4 31.8 HEX SHANK INCH mm 5/16 7.9 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 7/16 11.1 WEIGHT LBS. g .7 318 .8 363 1 454 1.2 545 1.2 545 1.5 681 1.6 726 1.8 817 2.3 1044 2.8 1270 Nail Eater II(R) Impact Bits * * * * * 52 Quickly bore through creosoted and salt treated utility poles. Resists wear, eats through nails and staples. Self-feeding screw point draws the bit through the wood. 7/16" hex shank to fit impact drivers. Available in 18" overall length. CAT. NO. UPC NO. HARDWARE DIA. INCH mm HOLE DIA. INCH mm OVERALL LENGTH INCH mm HEX SHANK INCH mm WEIGHT LBS. g 37868 37869 37870 37871 9/16 11/16 13/16 15/16 5/8 3/4 7/8 1 18 18 18 18 7/16 7/16 7/16 7/16 0.9 1.1 1.4 1.5 37868 37869 37870 37871 14.3 17.5 20.6 23.8 15.9 19.1 22.2 25.4 457.2 457.2 457.2 457.2 11.1 11.1 11.1 11.1 409 499 636 681 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com 149G E-Z BoreTM Bits REPLACEMENT PARTS CAT. NO. UPC NO. DESCRIPTION 4236AV 05133 Replacement Screw Point for 149G-1, 149G-1-1/8, 149G-1-1/4, 149G-1-3/8, 149G-1-1/2, 149G-1-3/4, 149G-2, 149G-2-1/8, 149G-2-1/4, 149G-2-9/16 and 149G-3 18358 18358 Replacement Screw Point for 149G-3-5/8 & 4-5/8 CAT. NO. UPC NO. HOLEMAKING * Double-end replaceable screw point. Choose the right feed for the material you are drilling. Fine thread for hardwoods, coarse thread for fast effortless drilling even in soft gummy woods. * Tapered backside for easier removal. * Open design won't clog with wood chips. * Three milled flats for use in portable electric or pneumatic drills and stationary boring machines. HOLE DIA. OVERALL LENGTH PIPE & WEIGHT INCH mm INCH mm CONDUIT SIZE LBS. g 149G-1 34985 1 25.4 5 127.0 1/2" .4 18 149G-1-1/8 29388 1-1/8 28.6 5 127.0 1/2" & 3/4" .3 137 149G-1-1/4 29389 1-1/4 31.8 5 127.0 3/4" .3 137 149G-1-3/8 29390 1-3/8 34.9 5 127.0 -- .4 182 149G-1-1/2 29391 1-1/2 38.1 5 127.0 1" .4 182 149G-1-3/4 29392 1-3/4 44.4 5 127.0 1-1/4" .5 227 149G-2 34986 2 50.8 5 127.0 -- .6 273 149G-2-1/8 29393 2-1/8 54.0 5 127.0 1-1/2" .7 318 149G-2-1/4 29395 2-1/4 57.2 5 127.0 -- .7 318 149G-2-9/16 29396 2-9/16 65.1 5 127.0 2" .8 363 149G-3 34987 3 76.2 5 127.0 2-1/2" 1.1 499 149G-3-5/8 29398 3-5/8 92.1 6-1/4 158.8 3" 2.1 953 149G-4-5/8 29400 4-5/8 117.5 6-1/4 158.8 4" 2.6 1179 53 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Conduit and Pipe Bit Sets 54 * Complete assortment of the most commonly used E-Z BoreTM bits. * High-impact, rugged plastic carrying case. * Full compliment of accessories conveniently stored. 1441 / 34995 Contractor's Bit Kit CAT. NO. UPC NO. DESCRIPTION 1441 34995 Contractor's Bit Kit WEIGHT LBS. kg 6 2.72 KIT CAT./UPC NO. 1441/34995 CAT. NO. UPC NO. DESCRIPTION 149G-1 34985 1" (25.4 mm) E-Z BoreTM Bit 149G-1-1/8 29388 1-1/8" (28.6 mm) E-Z BoreTM Bit 149G-1-1/4 29389 1-1/4" (31.8 mm) E-Z BoreTM Bit 149G-1-1/2 29391 1-1/2" (38.1 mm) E-Z Bit 149G-1-3/4 29392 1-3/4" (44.4 mm) E-Z BoreTM Bit 149G-2-1/8 29393 2-1/8" (54.0 mm) E-Z BoreTM Bit 149G-2-9/16 29396 2-9/16" (65.0 mm) E-Z BoreTM Bit 4236AV 05133 Double End Screw Point 51376 51376 1/8" Allen Wrench 52144 52144 5/32" Allen Wrench 904-5-1/2 34996 5-1/2" Bit Extension 34997 34997 Plastic Case BoreTM USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com D'VersiBIT(R) System It bends to meet your needs! Fishing wire or cable through existing walls used to be frustrating and timeconsuming, but the D'VersiBIT(R) has made it as simple as bowing the spring steel shaft in the direction you want to drill and turning on the power. Proven in the field to deliver accurate and professional results in many applications. Bits range from 3/16" to 1" (4.8 to 25.4 mm) in diameter and in shaft length from 12" to 72" (304.8 to 1828.8 mm). HOLEMAKING A new twist to an old problem. These flexible steel drill bits are the right tools for installing wire or cable inside existing walls. The D'VersiBIT(R) System makes it possible to easily accomplish even complex installations. This patented system attaches a quality drill bit to a long flexible spring steel shaft. When used with the Placement Tool, this flexibility makes it possible to easily manipulate the bit within walls. After drilling, attach a D'VersiGRIP to the hole in the drill and pull wire or cable back through the wall. Type M, Masonry Type HS High Speed Steel D'VERSIBIT(R) SHIPPING TUBES CAT. NO. 99104 UPC NO. 99104 99105 99105 DESCRIPTION 54" x 1" Shipping Tube B with End. (Sold only in minimum quantity of 6 in same length.) 72" x 1" Shipping Tube B with End. (Sold only in minimum quantity of 6 in same length.) * For drilling in masonry walls and * Designed for aggressive cutting in all through plaster. types of wood. * High speed bit head ensures longer * Recommended for use with Abrasion life. Shield to reduce friction and abrasion * Replaces Bellhanger drills on 12", 18" as the shaft turns against masonry. and 24" lengths. BIT DIAMETER INCH (mm) COLOR CODE SHAFT LENGTH INCH mm SHAFT DIA. TYPE M MASONRY INCH mm 1/4" 12 304.8 3/16 4.8 -- -- 1412D 39913 (6.4 mm) 18 457.2 3/16 4.8 -- -- 1418D 38744 Blue CAT. NO. UPC NO. TYPE HS HIGH SPEED STEEL CAT. NO. UPC NO. 24 609.6 3/16 4.8 -- -- 1424D 38745 36 914.4 3/16 4.8 -- -- 1436D 38746 12 304.8 3/16 4.8 -- -- 3812D 39914 3/8" 18 457.2 3/16 4.8 06-03-18M 38665 3818D 38749 (9.5 mm) 24 609.6 3/16 4.8 -- -- 3824D 38750 Black 36 914.4 3/16 4.8 -- -- 3836D 38751 54 1371.6 3/16 4.8 06-03-54M 38668 3858D 38752 72 1828.8 3/16 4.8 -- -- 3872D 38753 1/2" 36 914.4 3/16 4.8 -- -- 1236D 38756 (12.7 mm) 54 1371.6 3/16 4.8 -- -- 1258D 38757 Green 72 1828.8 3/16 4.8 -- -- 1272D 38758 54 1371.6 1/4 6.4 08-04-54M 38678 55 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING D'VersiBIT(R) System D'VERSIBIT(R) SHIPPING TUBES CAT. NO. 99104 UPC NO. 99104 DESCRIPTION 54" x 1" Shipping Tube B with End. (Sold only in minimum quantity of 6 in same length.) 99105 99105 72" x 1" Shipping Tube B with End. (Sold only in minimum quantity of 6 in same length.) Type A, Auger Type B, Combination with Screw Point Type C, Combination * Wood-type auger bit with screw point. * Pulls itself through wood, avoids walking or skidding. * Excellent for drilling in soft woods or through thin sections. * Slow back-taper allows for easy retrieval. * For aggressive chip removal in many types of woods. * Screw point for easy starting and pulling through wood. * With screw point removed, this bit can be ground to function like a standard combination bit. * For drilling in tough woods and thick obstacles. * Drilling speed relative to pressure applied. * Chips can be brought easily out of the hole. TYPE B COMBINATION WITH SCREW POINT CAT. NO. UPC NO. TYPE C COMBINATION CAT. NO. UPC NO. BIT DIA. INCH (mm) COLOR CODE SHAFT LENGTH INCH mm SHAFT DIA. INCH mm TYPE A AUGER CAT. NO. UPC NO. 1/4" 36 914.4 5/32 4.0 -- -- -- -- 04-03-36C (6.4 mm) 54 1371.6 5/32 4.0 -- -- -- -- 04-03-54C 38113 Blue 72 1828.8 5/32 4.0 -- -- -- -- 04-03-72C 38114 3/8" 36 914.4 3/16 4.8 06-03-36A 38067 06-03-36B 38092 06-03-36C 38117 (9.5 mm) 54 1371.6 3/16 4.8 06-03-54A 38068 06-03-54B 38093 06-03-54C 38118 Black 72 1828.8 3/16 4.8 06-03-72A 38069 06-03-72B 38094 06-03-72C 38119 1/2" 36 914.4 3/16 4.8 08-03-36A 38072 08-03-36B 38097 08-03-36C 38122 (12.7 mm) 54 1371.6 3/16 4.8 08-03-54A 38073 08-03-54B 38098 08-03-54C 38123 Green 72 1828.8 3/16 4.8 08-03-72A 38074 08-03-72B 38099 08-03-72C 38124 9/16" 36 914.4 3/16 4.8 09-03-36A 38077 09-03-36B 38102 -- -- (14.3 mm) 54 1371.6 3/16 4.8 09-03-54A 38078 09-03-54B 38103 09-03-54C 38128 Orange 72 1828.8 3/16 4.8 09-03-72A 38079 09-03-72B 38104 09-03-72C 38129 3/4" 36 914.4 1/4 6.4 12-04-36A 38082 -- -- -- -- (19.1 mm) 54 1371.6 1/4 6.4 12-04-54A 38083 -- -- 12-04-54C 38133 Red 72 1828.8 1/4 6.4 12-04-72A 38084 -- -- 12-04-72C 38134 1" 36 914.4 1/4 6.4 16-04-36A 38087 -- -- -- -- (25.4 mm) 54 1371.6 1/4 6.4 16-04-54A 38088 -- -- -- -- White 72 1828.8 1/4 6.4 16-04-72A 38089 -- -- -- -- 38112 D'VersiBIT(R) Starter Kit * All the tools to complete a typical wiring job. * Includes 09-03-54B bit, 712P placement tool and 150 pulling grip. 56 CAT. NO. UPC NO. DESCRIPTION DBITKIT 01630 D'VersiBIT Kit with 9/16" drill, placement tool and grip for pulling 1/2" OD wire. USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Placement Tool CAT. NO. UPC NO. DESCRIPTION 712P 38350 D'VersiBIT(R) Placement Tool SPECIFICATIONS Function Use to position all bit and shaft sizes. HOLEMAKING * Allows placement of the drill bit at any point within the wall. * Helpful in judging where the bit will be during drilling to avoid accidentally drilling through the wall. * Useful for vertical and horizontal placements. Wire and Cable Pulling Grips * Clip attaches to hole in bit, mesh basket holds wire or cable during recovery, swivel reduces twisting. * For use with bit 3/8" (9.5 mm) diameter or larger. * A variety of sizes for pulling wire and cable. CAT. NO. UPC NO. DESCRIPTION 125 38691 D'VersiGRIP for pulling single wire with 3/8" to 1/2" (9.5 mm to 12.7 mm) bits. 150 38692 D'VersiGRIP for pulling 1/2" (12.7 mm) OD wire with 1/2" to 9/16" (12.7 to 14.3 mm) bits. 168 38693 D'VersiGRIP for pulling 3/4" (19.1 mm) OD wire with 3/4" to 1" (19.2 to 25.4 mm) bits. SPECIFICATIONS Function For pulling wire, cable or fish tape through walls. Abrasion Shield * * * * SPECIFICATIONS Function Length Protects shaft and hand while drilling with any size or type D'VersiBIT(R). 48" (1219.2 mm) Tube fits both shaft sizes. Prevents insulation from wrapping around bit shaft. Protects shaft of masonry bits as they turn against masonry walls. Protects hand holding shaft during drilling. CAT. NO. UPC NO. DESCRIPTION 606AS 38696 Abrasion Shield Extensions * Sizes for 3/16" (4.8 mm) and 1/4" (6.4 mm) diameter shafts. * Connect to chuck end of D'VersiBIT(R) shaft to increase the length of the bit. USE WITH SPECIFICATIONS Size 3XT 36, 3XT 54, 3XT 72 - connecting end diameter 7/16" (11.1 mm) 4XT 36, 4XT 54, 4XT 72 - connecting end diameter 5/8" (15.9 mm) CAT. NO. 3XT 36 3XT 54 3XT 72 4XT 36 4XT 54 4XT 72 UPC NO. 38685 38686 38687 38688 38689 38690 SHAFT DIA. 3/16" (4.8 mm) 3/16" (4.8 mm) 3/16" (4.8 mm) 1/4" (6.4 mm) 1/4" (6.4 mm) 1/4" (6.4 mm) LENGTH 36" (914.4 mm) 54" (1371.6 mm) 72" (1828.8 mm) 36" (914.4 mm) 54" (1371.6 mm) 72" (1828.8 mm) 57 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Spade Bits 33A SPADE BITS - LENGTH 6-1/4" (158.8 mm) * * * * * * Bore hardwood, softwood, plywood and drywall. Forged and heat treated for long life. For use in 1/4" (6.4 mm) or larger power drills. Hole in top center of bit for wire pulling. See "Bit Extensions" if more length required (see below). P.O.P. packaged. SPECIFICATIONS 33A Spade Bit Length 6-1/4" (158.8 mm) 33L Spade Bit Length 16" (406.4 mm) SPADE BIT KIT CAT. NO. 33AR-6 UPC NO. 20364 DESCRIPTION Spade Bit Kit (see chart) WEIGHT LB. g .6 272 CAT. NO. 33A-1/4 33A-3/8 33A-1/2 33A-5/8 33A-3/4 33A-7/8 33A-1 33A-1-1/8 33A-1-1/4 33A-1-3/8 33A-1-1/2 UPC NO. 20344 20346 20348 20350 20352 20354 20357 20358 20359 20360 20361 HOLE DIA. INCH mm 1/4 6.4 3/8 9.5 1/2 12.7 5/8 15.9 3/4 19.1 7/8 22.2 1 25.4 1-1/8 28.6 1-1/4 31.8 1-3/8 34.9 1-1/2 38.1 33L SPADE BITS - LENGTH 16" (406.4 mm) HOLE DIA. CAT. NO. UPC NO. INCH 33L-1/4 31535 1/4 33L-3/8 31536 3/8 33L-1/2 31537 1/2 33L-5/8 31539 5/8 33L-3/4 31540 3/4 33L-7/8 31541 7/8 33L-1 31542 1 33L-1-1/8 31543 1-1/8 33L-1-1/4 31544 1-1/4 33L-1-1/2 31545 1-1/2 WEIGHT LBS. g .05 23.0 .09 40.8 .1 45.3 .1 45.3 .1 45.3 .12 54.4 .12 54.4 .15 68.0 .15 68.0 .16 72.6 .16 72.6 mm 6.4 9.5 12.7 15.9 19.1 22.2 25.4 28.6 31.8 38.1 KIT CAT./UPC NO. 33AR-6/ 20364 1 1 1 1 1 1 WEIGHT LBS. g .22 99 .32 145 .33 150 .4 181 .4 181 .55 250 .33 150 .58 263 .56 254 .6 272 Bit Extensions * Extend bit lengths - Holesaw arbors, Spade bits, Nail Eater II(R) bits, Electrician's bits and Step bits. * Use for boring deeper in wood. CAT. NO. LENGTH UPC NO. INCH mm HEX SHANK INCH mm HOLE DIA. INCH mm HEAD DIA. INCH mm 901-12 902-18 902-24 904-5-1/2 904H-12 904H-18 904H-24 02706 12 304.8 1/4 6.4 1/4 6.4 9/16 14.3 02707 18 457.2 5/16 7.9 23/64 9.1 21/32 16.7 02708 24 609.6 5/16 7.9 23/64 9.1 21/32 16.7 34996 5-1/2 139.7 7/16 11.1 1/2 12.7 1 25.4 34980 12 304.8 7/16 11.1 ** 23/32 18.3 35356 18 457.2 7/16 11.1 ** 23/32 18.3 35358 24 609.6 7/16 11.1 ** 23/32 18.3 WEIGHT LBS. g 1.4 2.5 3.4 2.1 2.9 4.3 5 636 1134 1543 953 1316 1951 2268 **For 7/16" Hex or 1/2" Round with 3 Flats, 1/4" Wide 58 BIT EXTENSION 901-12 902-18 and 902-24 HEX SHANK INCH mm 1/4 6.4 5/16 7.9 904 through 904H 7/16 CAT. NO. 3713GB 3678GB 3693GB 53892 UPC NO. 50962 50753 50765 53892 51376 51376 52144 52144 11.1 USE WITH 33A-5/16 through 33A-1-1/2 and 37157 arbor. 18-5/8 through 18-1; 45-5/8 through 45-13/16; 61PTS-5/8 through 61PTS-1; 66PT-3/8 through 66PT-9/16 and 37154 and 38522 arbors. 18-1-1/8 through 18-1-1/4; 45-7/8 through 45-1-1/2; 61/62PTS-1-1/8 and 61/62PTS-1-1/2; 62PTS-5/8 through 62PTS-1; 66PT-3/4 through 66PT-1-1/2 and 149G-1 through 149G-3 and 37155 and 37156 arbors. DESCRIPTION Set Screw for 901-12/02706 Set Screw for 902-18/02707 and 902-24/02708 Set Screw for 904-5-1/2/34996 Set Screw for 904H-12/24980, 904H-18/35356 and 904H-24/35358 Allen Wrench for use with set screws for 901-12/02706, 902-18/02707 and 902-24/02708 Allen Wrench for use with set screws for 904-5-1/2/34996 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Recessed Light Hole Saws Industry's only interchangeable replacement blades. Strong durable back plate. Available in two styles - steel tooth and carbide grit. Made and designed in USA by Greenlee. Use with a power drill to cut large diameter holes for recessed lighting fixtures. * Saws use Greenlee arbor 37156, purchased separately. SPECIFICATIONS Capacity Steel Toothed Blade - up to 7/8" (22.2 mm) plywood, wood, acoustical tile and ceiling tile. Carbide Grit Blade - up to 7/8" (22.2 mm) drywall, plywood, wood, acoustical tile, ceiling tile, plaster and stucco. CAT. NO. 35720 35721 35722 35723 35724 35725 35726 35727 35708 UPC NO. 35720 35721 35722 35723 35724 35725 35726 35727 35708 DESCRIPTION Replacement Blade for 35712 Replacement Blade for 35713 Replacement Blade for 35714 Replacement Blade for 35715 Replacement Blade for 35716 Replacement Blade for 35717 Replacement Blade for 35718 Replacement Blade for 35719 Set of 5 Blade Screws CAT./ UPC NO. 35712 35716 35713 35717 35714 35718 35715 35719 DESCRIPTION Steel Toothed Carbide Grit Steel Toothed Carbide Grit Steel Toothed Carbide Grit Steel Toothed Carbide Grit DIAMETER 4-3/8" (111 mm) 4-3/8" (111 mm) 6-3/8" (162 mm) 6-3/8" (162 mm) 6-5/8" (168 mm) 6-5/8" (168 mm) 6-7/8" (175 mm) 6-7/8" (175 mm) HOLEMAKING * * * * * HOLEWEIGHT LBS. kg USE FOR .76 .34 Mini Juno, Capri, .74 .34 Marco and Halo 1.2 .54 Halo and Capri 1.1 .50 Halo and Capri 1.3 .59 Juno and Progress 1.3 .59 Juno and Progress 1.3 .59 Lithonia, Marco, 1.4 .64 Lightolier, Progress, Capri and Precolite Quick CutterTM Hole Saws * Quickest, most affordable way to cut perfect holes in drywall and ceiling tile. * Cuts clean, precise holes that ensure no light leakage or poor-fitting installations. * Self-sharpening, carbide-sprayed cutting tips can cut dozens of holes in very abrasive materials and still stay sharp. * Stabilizer spring balances cutting forces and offers more control of the tool when drilling drywall. * Dedicated arbor and pilot drill eliminates changeover time. * Fits a 3/8" drill chuck and can be used with a cordless drill. * Included dust shield virtually eliminates flying dust and debris (available in 6-1/2", 6-7/8" and adjustable models only). CAT. NO. 06923 UPC NO. 06923 06924 06924 06925 06925 06926 06926 DESCRIPTION Quick CutterTM Recessed Hole Saw, adjustable 2-1/2" to 7" cuts 2-1/2" to 7" diameter holes in increments of 1/2" Quick CutterTM Recessed Hole Saw, sprinkler head 2-1/2" cuts holes for standard sprinkler heads Quick CutterTM Recessed Hole Saw, fixed blade 6-1/2" Halo(R), Capri(R), Catalina(R), and Commercial Electric(R) lighting Quick CutterTM Recessed Hole Saw, fixed blade 6-7/8" Juno(R) lighting Keyhole Saw * Ergonomic style handle with non-slip grip creates a sure, and comfortable feel. * Hardened steel blade makes cutting drywall, cement board, plastic and wood quick and easy. * Blade goes through the handle for maximum support of the cutting blade. HACK SAW FRAMES AND BLADES CAT. NO. UPC NO. DESCRIPTION 301 01641 Keyhole saw with 6" blade (152 mm) 59 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Masonry Bits * Steel bit with carbide tip. * Use in concrete, block, brick, stone, wallboard and plaster. * Available in two styles: percussion for use in electric hammer and fast spiral for use in conventional power drills. * Available in sizes ranging from 3/16" - 1/2" (4.8 - 12.7 mm). Fast Spiral PERCUSSION BITS CAT./ UPC NO. 84576 HOLE DIA. INCH mm 3/16 4.8 SHANK INCH mm 3/16 4.8 WEIGHT LBS. g .03 14 84582 1/4 6.4 1/4 6.4 .05 23 SPECIFICATIONS 84588 5/16 7.9 1/4 6.4 .06 27 Twist Length 2-1/2" (63 mm) 84594 3/8 9.5 1/4 6.4 .08 36 4" (101 mm) 84600 1/2 12.7 1/4 6.4 .12 54 Percussion Overall Length FAST SPIRAL BITS CAT./ UPC NO. 84526 HOLE DIA. INCH mm 3/16 4.8 SHANK INCH mm 3/16 4.8 WEIGHT LBS. g .03 14 84532 1/4 6.4 1/4 6.4 .05 23 84538 5/16 7.9 1/4 6.4 .06 27 84544 3/8 9.5 1/4 6.4 .08 36 84550 1/2 12.7 1/4 6.4 .12 54 Anchor and Fastener Selection Guide ANCHOR/FASTENER TYPE USE IN USE WITH MADE OF SIZE RANGE GENERAL INFORMATION Concrete, brick, stone, block Machine screw or bolts Zinc alloy and lead #8-32 to 1/2"-13 Single unit caulking anchor, can be set shallow (flush) or deep in hole. Setting tool required (1 provided free in each box of anchors). For setting in hollow block or to set anchors all at the same depth, use Greenlee Screw anchor expander. Concrete, brick, stone Machine screw or bolts Steel 1/4"-20 to 3/8"-16 Heavy-duty use in solid masonry where codes require all steel bolt anchors. Pre-assembled, internal expander plug. Can be installed flush with masonry surface or sub-set. Setting tool required (1 provided free in each box of anchors). Concrete, block, brick No other fastener needed Steel 1/4" x 1" to 1/4" x 2-1/2" A safe, secure fastener that actually taps concrete and eliminates the need for concrete inserts with their alignment problems. Use with Greenlee masonry drill set tool. Block, wallboard, plaster, tile No other fastener needed Steel 1/8" x 3" to 1/4" x 6" Available in round head and mushroom head. Fully-threaded machine screw with spring wing toggle head. Concrete, block, brick No other fastener needed Zinc and Steel 3/16" x 7/8" to 1/4" x 2" Fast, medium-duty. No hole spotting, removable. Use in hollow or solid base applications. Concrete, block, tile, brick Sheet metal, Corrosionwood, lag resistant screws plastic #6-8 x 3/4" to #10-12 x 1-1/2" Light-duty, multi-size anchor. Has collar for hollow materials. Caulking Drop Masonry Screw Toggle Bolts Zinc Mushroom Head Plastic Conical 60 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Screw Anchor Expanders for Caulking Anchors 1. Drill hole of required size and put anchor screw on expander. Insert screw anchor into drilled hole. 2. Strike head of expander with hammer or mallet until anchor is held securely in wall. Unscrew expander. CAT. NO. UPC NO. EXPANSIVE BELT SIZE USE WITH ANCHOR NO. QTY. PER BOX WEIGHT LB. kg 866 02667 #10 - 24 84296 1 .3 .1 868 02669 1/4" - 20 84299 1 .4 .2 870 02671 3/8" - 16 84305 1 .6 .3 CAT. NO. UPC NO. DESCRIPTION 4451AV 05191 Anchor Screw for 866 4457AV 05197 Anchor Screw for 868 4717AV 05300 Anchor Screw for 870 HOLEMAKING * Quickly and securely set expansive screw anchors in masonry, regardless of thickness. * Hardened alloy steel. * Patented. Caulking Anchors * Zinc alloy and lead caulking anchor can be set flush or subset. Greenlee setting tool required. * Rustproof, use interior or exterior. * For setting in hollow block. To set anchors all same depth, use Greenlee screw anchor expander. LEAD CAULKING ANCHORS AND SETTING TOOLS CAT./ THREAD UPC NO. SIZE 1. Drill hole in masonry. 2. Insert anchor, conical end first, until flush with surface. 3. Using setting tool, caulk lead outer sleeve with sharp blows. Position fixture. 4. Insert screw or bolt and tighten. REQ. HOLE SET QTY. WEIGHT DIA. MIN. DEPTH TOOL* PER BOX LBS. kg WORKING LOAD PULLOUT LBS. kg 84299 1/4"-20 1/2" 7/8" 84329 100 3.8 1.7 125 56.6 84305 3/8"-16 3/4" 1-1/4" 84335 50 7.1 3.2 312.5 141.6 *One Setting Tool included with each box of anchors. Approvals: Conforms to the description in Federal Specification FFS-325, Group I, Type 1, Class 1. NOTE: Working load is one fourth the ultimate/maximum capacity. For critical or unusual applications, site testing is recommended. Drop Anchors * Heavy-duty steel anchor for use where codes require all steel bolt anchors. * Pre-assembled, internal expander plug for faster installation. * Four-way slot design assures firm hold. DROP ANCHORS AND SETTING TOOLS CAT./ UPC NO. TO SET ANCHOR FLUSH WITH SURFACES ANCHOR & BOLT MIN. THREAD SETTING QTY. WEIGHT HOLE DIA. THREAD SIZE DEPTH DEPTH TOOL* PER BOX LB. kg 84253 3/8" 1/4"-20 1-1/8" 1/2" 84273 100 3 1.4 84256 1/2" 3/8"-16 1-5/8" 5/8" 84276 50 7 3.2 *One Setting Tool included with each box of anchors. SPECIFICATIONS 1. Drill hole the same diameter as anchor being used. 2. Drive anchor flush with concrete. 3. Expand anchor with setting tool provided. Anchor is properly expanded when shoulder of setting tool is flush with top of anchor. TO SET ANCHOR BELOW SURFACES 1. Drill hole deeper than anchor length. Thread bolt into anchor. Hammer anchor into hole until bolt head is at desired height. Remove bolt and set anchor with setting tool. NOTE: The use of a 24 to 40 ounce hammer is recommended for expanding the anchor. CAT./UPC NO. WORKING LOAD PULLOUT LBS. kg WORKING LOAD SHEAR LBS. kg 84253 1037 469.8 842.5 381.7 84256 1712.5 775.8 1518.7 688.9 Approvals: Conforms to the description in Federal Specification FFS-325, Group VIII, Type 1, for concrete expansion shield anchors. NOTE: Working load is one fourth the ultimate/maximum capacity. For critical or unusual applications, site testing is recommended. 61 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING Masonry Screw Anchors * A safe, secure, steel fastener that taps concrete and eliminates the need for concrete inserts with their alignment problems. * Use with Greenlee masonry drill set tool. * Use in concrete, block and brick. * Quick and easy two step installation, saves time. * Made in USA. Masonry Screw Anchors must be used with Greenlee masonry screw drill bits, numbers 84484 and 84487, which are a special size to insure secure thread engagement. Standard masonry bit size holes will not provide proper contact with screw threads and may cause masonry anchor screws to pull out. 1. Use set Tool with bit in drilling position to drill hole in surface. 2. Retract bit, insert masonry screw into socket head of tool and drive screw into hole. MASONRY SCREW ANCHORS - EACH BOX OF 100 INCLUDES 1 BIT CAT./ UPC NO. SIZE MATERIAL CONCRETE 3000 PSI MIN. EMBEDMENT PULLOUT LBS. QTY. PER BOX LBS. 84469 1/4" x 1" 3/4" 84472 1/4" x 1-1/4" 84475 1/4" x 1-1/2" WT. 1180 100 1.2 .5 3/4" 1180 100 1.4 .6 1-1/4" 1800 100 1.6 .7 kg 84478 1/4" x 2" 1-1/4" 1800 100 1.8 .8 84481 1/4" x 2-1/2" 1-1/4" 1800 100 2.1 1.0 MASONRY SCREW DRILL SET KIT INSTALLATION TOOLS QTY. PER WT. BOX LBS. kg CAT./ UPC NO. DESCRIPTION 84466 Masonry Screw Drill Set Tool with 84484 Bit 1 84484 3-1/2" Masonry Screw Drill Bit - for use with 1" to 1-1/2" long screws 1 .4 .2 NOTE: For use in lightweight, hollow core concrete block, minimum embedment 1-3/8", pullout 715 lbs. Due to the variance in make-up of cement block, values will vary. It is suggested that the anchor be tested in specific material being used before installing fixtures. MATERIAL CONCRETE 3000 PSI QTY. MIN. PULLOUT PER WT. EMBEDMENT LBS. BOX LBS. kg CAT./ UPC NO. DESCRIPTION 84463 Masonry Screw Drill Set Kit Includes: 84469 50 - 1/4" x 1" Masonry Screws 3/4" 84472 50 - 1/4" x 1-1/4" Masonry Screws 84466 1- Masonry Screw Drill Set Tool with 84484 Bit 1180 1 1.6 .7 Small Jobs - Use special Greenlee masonry screw drill bit for holes. Screw can be installed with 5/16" wrench, nut driver or socket with ratchet. Large Jobs - Use the special Greenlee Masonry Screw Drill Set Tool in kit with 3/8" or larger electric drill for drilling holes and screw installation. Toggle Bolts and Spring Wings * For light to medium fastening in block, wallboard, plaster and hollow tile. * Fully threaded machine screw with spring wing toggle head. * Generous size of toggle head acts to spread the load over a maximum area. * Made in USA. Round Head TOGGLE BOLTS AND SPRING WINGS CAT./ UPC NO. Mushroom Head 1. Drill hole completely through wall. 62 2. Insert bolt through items to be fastened. Fold wings completely back, then push through hole until wings spring open. 3. Pull back to hold wings against inside wall while tightening with screw driver. TOGGLE BOLT SIZE HEAD REQUIRED HOLE SIZE QTY. PER BOX WEIGHT LBS. kg 84405 84409 1/4" x 4" 3/8" x 4" Round Round 11/16" 1" 50 25 3.7 4.3 1.7 1.9 84424 84425 3/16" x 3" 3/16" x 4" Mushroom Mushroom 1/2" 1/2" 50 50 1.9 2.2 .9 1.0 84428 84429 1/4" x 3" 1/4" x 4" Mushroom Mushroom 11/16" 11/16" 50 50 3.3 3.8 1.5 1.7 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com Zinc Mushroom Head Drive Anchors Solid Wall 1. Drill required diameter hole in material, to a minimum depth equal the overall anchor minus the thickness of the object to be fastened. Clean hole. 2. Insert anchor body through object to be fastened, and into the hole in base material. Hollow Wall 3. Tap the nail until it is flush with the zinc anchor head. Fast, medium-duty anchor for use in concrete, block and brick. No hole spotting. Use in hollow or solid material. Made of zinc and steel. CAT./ UPC NO. 84110 SIZE 1/4" x 1" REQUIRED HOLE SIZE 1/4" QTY PER BOX 100 WEIGHT LBS. kg 2 .9 84111 1/4" x 1-1/4" 1/4" 100 2.4 1.1 84112 1/4" x 1-1/2" 1/4" 100 2.6 1.2 NOTE: For critical or unusual applications, site testing is recommended. HOLEMAKING * * * * Plastic Conical Anchors * * * * * ANCHORS ONLY B C 1. Drill hole full length of anchor or 1/8" deeper. Light-duty, multi-size anchor for use in concrete, block, tile and brick. Use with sheet metal, wood and lag screws. Has collar for hollow materials. Moisture and chemical resistant, for indoor/outdoor use. Anchor kits include 100 anchors, 100 screws and one masonry bit. 2. Tap anchor into hole flush with surface. 3. Insert screw through fixture into plastic plug and tighten. CAT./ UPC NO. USE WITH SCREW SIZES 84003 #6 - #8 3/16" 100 .2 .1 84006 #10, #12 1/4" 100 .2 .1 ANCHOR KITS CAT./ ANCHOR UPC NO. SIZE REQUIRED HOLE SIZE QTY. PER BOX SCREW WEIGHT LBS. kg SIZE TYPE BIT SIZE WEIGHT LBS. kg 84009 #6, #8 #8 x 1" C 3/16" .8 .4 84012 #10, #12 #10 x 1" C 1/4" 1 .5 84015 #10, #12 #12 x 1" C 1/4" 1.4 .6 84019 #10, #12 #10 x 1" B 1/4" 1.1 .5 63 USA Tel: 800-435-0786 Canada Tel: 800-435-0786 International Tel: +1-815-397-7070 Fax: 800-451-2632 Fax: 800-524-2853 Fax: +1-815-397-9247 greenlee.com HOLEMAKING TAPCON(R) Masonry Fasteners and Drill Bits * Corrosion resistant - All Tapcon(R) fasteners are protected against rust and corrosion by the exclusive Stalgard(R) finish. * Fast - Install two or three Tapcon fasteners per minute. Simple two-step operation - drill, then drive - eliminates the need to set anchors. * Strong - Tapcon fasteners and the masonry material are mechanically linked for exceptionally strong pullout strength. * Removable - Tapcon fasteners can be removed and reinserted in the same hole. Great for repairs or adjustments. * Available in two diameters - 1/4" and 3/16". * Made in USA. A Slotted Hex Washer Head TAPCON(R) MASONRY FASTENERS - EACH BOX OF 100 INCLUDES 1 BIT FASTENER CAT. NO. LE 405 LE 415 LE 425 LE 435 LE 445 LE 455 LE 300 LE 310 LE 320 UPC NO. 07405 07415 07425 07435 07445 07455 07300 07310 07320 SIZE 1/4" x 1-1/4" 1/4" x 1-3/4" 1/4" x 2-1/4" 1/4" x 2-3/4" 1/4" x 3-1/4" 1/4" x 3-3/4" 3/16" x 1-1/4" 3/16" x 1-3/4" 3/16" x 2-1/4" EMBEDMENT MIN. MAX. 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" 1" 1-3/4" TYPE A A A A A A A A A MAXIMUM ATTACHMENT THICKNESS 1/4" 3/4" 1-1/4" 1-3/4" 2-1/4" 2-3/4" 1/4" 3/4" 1-1/4" QTY. PER BOX 100 100 100 100 100 100 100 100 100 Multi-Purpose Installation Tool * Multipurpose tool designed to be used with all sizes and styles of Tapcon masonry fasteners. * Tapcon anchors are easy to install...a simple two-step operation - drill the hole, then drive the fastener with the Condrive tool. CAT. NO. UPC NO. DESCRIPTION LP 100 07100 Condrive 1000 Kit Consists of Drill Adapter, Drill Sleeve Assembly, 5/16" Hex DriverMagnetic, 1/4" Hex Socket for 3/16" Anchor, Phillips Bit, #2 Phillips Bit, #3 Phillips Bit, 1/8" Hex Key, Set Screw 1/4-28, Drive Sleeve Assembly for 5" & 6" Anchors High Speed Installation Tool * Convenient one step tool designed for high speed installation of Tapcon fasteners. * Best for rapid, repetitive drilling and fastener installation. * Specifically designed for hex head Tapcon fasteners in lengths up to 2-3/4". 64 CAT. NO. UPC NO. DESCRIPTION LP 200 07200 Condrive 2000 Kit Consists of Tool Body / Drive Assembly, 5/16" Hex Socket for 1/4" Anchors, 1/4" Hex Socket for 3/16" Anchors, 1/8" Hex Key, 1/4" Hex Key, 5/16" Hex Key, Set Screw