D WIMA MKS 2 Metallized Polyester (PET) Capacitors in PCM 5 mm. Capacitances from 0.01 mF to 10 mF. Rated Voltages from 50 VDC to 630 VDC. Special Features Electrical Data High volume/capacitance ratio Self-healing AEC-Q200 qualified According to RoHS 2011/65/EU Typical Applications For general DC-applications e.g. By-pass Blocking Coupling and decoupling Timing Construction Capacitance range: 0.01 mF to 10 mF (E12-values on request) Rated voltages: 50 VDC, 63 VDC, 100 VDC, 250 VDC, 400 VDC, 630 VDC Capacitance tolerances: 20%, 10%, 5% Operating temperature range: U r = 50 VDC: -55+ C to +100+ C U r 63 VDC: -55+ C to +125+ C Climatic test category: 55/100/21 in accordance with IEC Insulation resistance at +20+ C: U test Ur Dielectric: Polyethylene-terephthalate (PET) film Capacitor electrodes: Vacuum-deposited Internal construction: 50 VDC10 V 63 VDC50 V U100 VDC 100 V Vacuum-deposited electrode Metal contact layer (schoopage) Terminating wire C 0.33 mF 0.33 mF < C T 10 mF 5 x 103 M 1000 sec (M x mF) 1 x 104 M 1 kHz 10 kHz 100 kHz C 0.1 mF 10 -3 8x 15 x 10 -3 30 x 10 -3 3000 sec (M x mF) 0.1 mF < C T 1.0 mF 10-3 8x 15 x 10-3 - C > 1.0 mF 10 x 10-3 - - Maximum pulse rise time: for pulses equal to the rated voltage Capacitance mF 50 VDC Encapsulation: Solvent-resistant, flame-retardant plastic case with epoxy resin seal, UL 94 V-0 Terminations: Tinned wire. Marking: Colour: Red. Marking: Silver/White. 1250 sec (M x mF) 1.5 x 104 M Measuring time: 1 min. Dissipation factors at + 20) C: tan d at f Plastic film Test specifications: In accordance with IEC 60384-2 Test voltage: 1.6 Ur, 2 sec. Voltage derating: A voltage derating factor of 1.25 % per K must be applied from +85+ C for DC voltages and from +75+ C for AC voltages Reliability: Operational life 300 000 hours (+125 C permitted for 1000 hours max. distributed over the entire operating life) Failure rate 2 fit (0.5 x Ur and 40) C) 0.01 0.033 0.1 0.68 1.5 ... ... ... ... ... 0.022 - 0.068 - 0.47 10/100 1.08/80 3.38/80 4.7 5/50 6.8 3/30 10 2.5/25 63 VDC 35/350 20/200 15/150 12/120 7.5/75 5/50 3/30 - Mechanical Tests 35/350 25/250 20/200 15/150 10/100 - - - 50/500 50/500 50/500 25/250 - - - - 80/800 80/800 80/800 - - - - - 630 VDC 110/1100 90/900 - - - - - - Packing Available taped and reeled. Detailed taping information and graphs at the end of the catalogue. For further details and graphs please refer to Technical Information. 01.19 Pull test on pins: 10 N in direction of pins according to IEC 60068-2-21 Vibration: 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 4000 bumps at 390 m/sec2 in accordance with IEC 60068-2-29 Pulse rise time V/msec max. operation/test 100 VDC 250 VDC 400 VDC 44 D WIMA WIMA MKS FKP 42 Continuation General Data Capacitance 0.01 0.015 0.022 0.033 0.047 0.068 W H L 50 VDC/30 VAC* PCM** Part number W H 63 VDC/40 VAC* PCM** Part number L 2.5 6.5 2.5 6.5 2.5 6.5 2.5 6.5 2.5 6.5 2.5 6.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2C021001A00_ _ _ _ MKS2C021501A00_ _ _ _ MKS2C022201A00_ _ _ _ MKS2C023301A00_ _ _ _ MKS2C024701A00_ _ _ _ MKS2C026801A00_ _ _ _ 0.1 mF 0.15 0.22 0.33 2.56.5 7.2 5 MKS2B033301A00_ _ _ _ 0.47 37.5 7.2 5 MKS2B034701B00_ _ _ _ 0.68 3.58.5 7.2 5 MKS2B036801C00_ _ _ _ 2.5 6.5 2.56.5 37.5 3.5 8.5 3.5 8.5 4.5 9.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2C031001A00_ _ _ _ MKS2C031501A00_ _ _ _ MKS2C032201B00_ _ _ _ MKS2C033301C00_ _ _ _ MKS2C034701C00_ _ _ _ MKS2C036801E00_ _ _ _ 1.0 1.5 2.2 3.3 4.7 6.8 5 5.5 7.2 7.2 8.5 11 10 7.2 11.5 7.2 137.2 137.2 147.2 16 7.2 5 5 5 5 5 5 MKS2C041001F00_ _ _ _ MKS2C041501H00_ _ _ _ MKS2C042201K00_ _ _ _ MKS2C043301K00_ _ _ _ MKS2C044701M00_ _ _ _ MKS2C046801N00_ _ _ _ mF mF 10 mF Capacitance 3.58.5 4.59.5 5 10 5.5 11.5 7.2 13 8.5 14 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2B041001C00_ _ _ _ MKS2B041501E00_ _ _ _ MKS2B042201F00_ _ _ _ MKS2B043301H00_ _ _ _ MKS2B044701K00_ _ _ _ MKS2B046801M00_ _ _ _ 11 16 7.2 5 MKS2B051001N00_ _ _ _ W H L 100 VDC/63 VAC* PCM** Part number W H L 250 VDC/160 VAC* PCM** Part number 0.01 0.015 0.022 0.033 0.047 0.068 mF 2.56.5 2.5 6.5 2.5 6.5 2.5 6.5 2.5 6.5 2.5 6.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2D021001A00_ _ _ _ MKS2D021501A00_ _ _ _ MKS2D022201A00_ _ _ _ MKS2D023301A00_ _ _ _ MKS2D024701A00_ _ _ _ MKS2D026801A00_ _ _ _ 2.5 6.5 2.5 6.5 2.5 6.5 3.5 8.5 3.5 8.5 3.5 8.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2F021001A00_ _ _ _ MKS2F021501A00_ _ _ _ MKS2F022201A00_ _ _ _ MKS2F023301C00_ _ _ _ MKS2F024701C00_ _ _ _ MKS2F026801C00_ _ _ _ 0.1 0.15 0.22 0.33 0.47 0.68 mF 2.56.5 3.58.5 3.58.5 4.59.5 4.59.5 5 10 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2D031001A00_ _ _ _ MKS2D031501C00_ _ _ _ MKS2D032201C00_ _ _ _ MKS2D033301E00_ _ _ _ MKS2D034701E00_ _ _ _ MKS2D036801F00_ _ _ _ 4.5 9.5 7.2 5 10 7.2 5.5 11.5 7.2 7.2 137.2 8.5 147.2 11 16 7.2 5 5 5 5 5 5 MKS2F031001E00_ _ _ _ MKS2F031501F00_ _ _ _ MKS2F032201H00_ _ _ _ MKS2F033301K00_ _ _ _ MKS2F034701M00_ _ _ _ MKS2F036801N00_ _ _ _ 1.0 mF 1.5 2.2 7.2 13 8.5 14 11 16 7.2 7.2 7.2 5 5 5 MKS2D041001K00_ _ _ _ MKS2D041501M00_ _ _ _ MKS2D042201N00_ _ _ _ * AC voltage: f = 50 Hz; 1.4 x U rms + UDC U r ** PCM = Printed circuit module = pin spacing. W L Dims. in mm. H 6 -2 d = 0.5 P d 5 PCM at the pin exit points ( 0.5) Part number completion: Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = SD Taped version see page 149. Rights reserved to amend design data without prior notification. 01.19 Continuation page 46 45 D WIMA MKS 2 Continuation General Data 400 VDC/200 VAC* PCM** Part number Capacitance W 0.01 0.015 0.022 0.033 0.047 0.068 2.56.5 2.5 6.5 3.5 8.5 4.5 9.5 4.5 9.5 5.5 11.5 7.2 7.2 7.2 7.2 7.2 7.2 5 5 5 5 5 5 MKS2G021001A00_ _ _ _ MKS2G021501A00_ _ _ _ MKS2G022201C00_ _ _ _ MKS2G023301E00_ _ _ _ MKS2G024701E00_ _ _ _ MKS2G026801H00_ _ _ _ 7.2 13 8.5 14 11 16 7.2 7.2 7.2 5 5 5 MKS2G031001K00_ _ _ _ MKS2G031501M00_ _ _ _ MKS2G032201N00_ _ _ _ mF 0.1 mF 0.15 0.22 H L W 5.5 7.2 7.2 7.2 8.5 H L 630 VDC/220 VAC* PCM** Part number 11.5 7.2 137.2 137.2 137.2 147.2 5 5 5 5 5 MKS2J021001H00_ _ _ _ MKS2J021501K00_ _ _ _ MKS2J022201K00_ _ _ _ MKS2J023301K00_ _ _ _ MKS2J024701M00_ _ _ _ * AC voltage: f = 50 Hz; 1.4 x U rms + UDC U r ** PCM = Printed circuit module = pin spacing. Dims. in mm. The values of the WIMA MKM 2 range according to the main catalogue 2009 are still available on request. Part number completion: Tolerance: 20 % = M 10 % = K 5 % = J Packing: bulk = S Pin length: 6-2 = SD Taped version see page 149. Impedance change with frequency (general guide). Rights reserved to amend design data without prior notification. 01.19 Permissible AC voltage in relation to frequency at 10) C internal temperature rise (general guide). 46 D Recommendation for Processing and Application of Through-Hole Capacitors Soldering Process Internal temperature of the capacitor must be kept as follows: Polyester: preheating: T max. T 125 C soldering: T max. T 135 C Polypropylene: preheating: Tmax. T 100 C soldering: T max. T 110 C Single wave soldering Soldering bath temperature: T P 260 C Dwell time: t P 5 sec Double wave soldering Soldering bath temperature: T P 260 C Dwell time: St P 5 sec Due to different soldering processes and heat requirements the graphs are to be regarded as a recommendation only. WIMA Quality and Environmental Philosophy ISO 9001:2015 Certification ISO 9001:2015 is an international basic standard of quality assurance systems for all branches of industry. The approval according to ISO 9001:2015 of our factories by the infaz (Institut fur Auditierung und Zertifizierung) certifies that organisation, equipment and monitoring of quality assurance in our factories correspond to internationally recognized standards. WIMA WPCS The WIMA Process Control System (WPCS) is a quality surveillance and optimization system developed by WIMA. WPCS is a major part of the quality-oriented WIMA production. Points of application during production process: incoming material inspection metallization film inspection schoopage pre-healing pin attachment cast resin preparation/ encapsulation " 100% final inspection " Testing as per customer requirements All WIMA capacitors, irrespective of whether through-hole devices or SMD, are made of environmentally friendly materials. Neither during manufacture nor in the product itself any toxic substances are used, e.g. - - - - - Lead PCB CFC Hydrocarbon chloride Chromium 6+ - - - - - PBB/PBDE Arsenic Cadmium Mercury etc. We merely use pure, recyclable materials for packing our components, such as: " " " " carton cardboard adhesive tape made of paper polystyrene We almost completely refrain from using packing materials such as: " adhesive tapes made of plastic " metal clips RoHS Compliance According to the RoHS Directive 2011/65/EU as amended from time to time certain hazardous substances like e.g. lead, cadmium, mercury must not be used any longer in electronic equipment as of July 1st, 2006. For the sake of the environment WIMA has refraind from using such substances since years already. WIMA Kondensatoren sind bleifrei konform RoHS 2011/65/EU WIMA capacitors are lead free in accordance with RoHS 2011/65/EU Tape for lead-free WIMA capacitors DIN EN ISO 14001:2004 WIMA's environmental management has been established in accordance with the guidelines of DIN EN ISO 14001:2004 to optimize the production processes with regard to energy and resources. 01.19 " " " " " " " WIMA Environmental Policy 15 D Typical Dimensions for Taping Configuration Vh P P2 Diagram 1: PCM 2.5/5/7.5mm W W1 W0 H H1 W2 P1 D0 d P t F P0 H1 P P1 H P1 d d P0 P2 F F Diagram 2: PCM 10/15 mm Diagram 3: PCM 22.5 and 27.5*mm *PCM 27.5 taping possible with two feed holes between components Designation Carrier tape width Dimensions for Radial Taping Symbol PCM 2.5 taping W P0 P2 18.0 p0.5 PCM 5 taping PCM 7.5 taping PCM 10 taping* PCM 15 taping* PCM 22.5 taping PCM 27.5 taping 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 18.0 p0.5 for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing for hot-sealing Hold-down tape width W0 6.0 6.0 12.0 12.0 12.0 12.0 12.0 adhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tapeadhesive tape Hole position W1 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 9.0 p0.5 Hold-down tape position W2 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. 0.5 to 3.0 max. Feed hole diameter D0 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 4.0 p0.2 12.7 p1.0 12.7 p1.0 12.7 p1.0 25.4 p1.0 25.4 p1.0 38.1 p1.5 4.0 p0.2 3*8.1 p1.5 or 50.8 p1.5 Pitch of component P Feed hole pitch P0 12.7 cumulative pitch p0.3 error max. 1.0 mm/20 pitch Feed hole centre to pin P1 5.1 p0.5 Hole centre to component centre P2 12.7 cumulative pitch p0.3 error max. 1.0 mm/20 pitch 12.7 cumulative pitch p0.3 error max. 1.0 mm/20 pitch 12.7 cumulative pitch p0.3 error max. 1.0 mm/20 pitch 12.7 cumulative pitch p0.3 error max. 1.0 mm/20 pitch 12.7 p0.3 9.0 p0.5 cumulative pitch error max. 1.0 mm/20 pitch 12.7 p0.3 cumulative pitch error max. 1.0 mm/20 pitch 3.85 p0.7 2.6 p0.7 7.7 p0.7 5.2 p0.7 7.8 p0.7 5.3 p0.7 6.35 p1.3 6.35 p1.3 6.35 p1.3 12.7 p1.3 12.7 p1.3 19.05 p1.3 19.05 p1.3 Feed hole centre to bottom H edge of the component 16.5 p0.3 18.5 p0.5 16.5 p0.3 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 16.5 p0.5 18.5 p0.5 Feed hole centre to top H edge of the component1 H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 32.25 max. H+Hcomponent < H1 24.5 to 31.5 H+Hcomponent < H1 25.0 to 31.5 H+Hcomponent < H1 26.0 to 37.0 H+Hcomponent < H1 30.0 to 43.0 H+Hcomponent < H1 35.0 to 45.0 Pin spacing at +0.8 F 2.5 p0.5 5.0 upper edge of carrier tape -0.2 7.5 p0.8 10.0 p0.8 15 p0.8 22.5 p0.8 27.5 p0.8 Pin diameter d 0.4 p0.05 Component alignment Dh p 2.0 max. p 2.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. p 3.0 max. 0.6 p0.2 0.6 p0.2 0.6 p0.2 0.6 p0.2 0.6 p0.2 0.6 p0.2 0.6 p0.2 Total tape thickness t Package (see also page 150) REEL 0.5 p0.05 0.5 +0.06 p0.05 or 0.6 -0.05 0.5 +0,06 p0.05 or 0.6 -0.05 ROLL/AMMO P 360 max. 52 p2 B p2 P 30 p158 depending on comp. dimensions Unit 0.8 +0,08 -0.05 0.8 +0,08 -0.05 +0.08 0.8 -0.05 AMMO 52 p254 p2 max. P 500 max. B 58 p2 or REEL B 60 p2 REEL PP 360 30 p1 P 25 p1 66 p2 68 p2 depending on PCM and component dimensions see details page 151. Dims in mm. 01.19 Diameter of pins see General Data. Please clarify customer-specific deviations with the manufacturer. * PCM 10 and PCM 15 can be crimped to PCM 7.5. Position of components according to PCM 7.5 (sketch 1). P 0 = 12.7 or 15.0 is possible 149 D Types of Tape Packaging of Capacitors for Automatic Radial Insertion REEL Packaging 340 max. 301 251 360 max. 500 max. AMMO Packaging 340 max. 370 max. ROLL Packaging 34 0m ax. 50 max. 50 max. 70 max. . ax 0 m ax. 34 0 m 49 B BAR CODE (Labelling) Labelling of package units in plain text and with alphanumerical Bar Code BARCODE Code 39" Scanner decoding of WIMA supplier number Customer`s P/O number Customer`s part number WIMA confirmation number WIMA part number Lot number Date code Quantity In addition part description of - - - - - - article capacitance value rated voltage dimensions capacitance tolerance packing 01.19 as well as gross weight and customer`s name are indicated in plain text. 150 D Packing Quantities for Capacitors with Radial Pins in PCM 2.5 mm to 22.5 mm Size PCM 2.5 mm 5 mm 7.5 mm 10 mm 15 mm 22.5 mm W 2.5 3 3.8 4.6 5.5 2.5 3 3.5 4.5 4.5 5 5.5 5.5 6.5 7.2 7.2 8.5 8.5 11 2.5 3 4 4.5 5 5.7 7.2 3 4 4 4 5 5 6 6 8 5 5 6 6 7 7 8 8 9 9 10 11 5 6 7 8 8.5 10 10.5 10.5 11 12 H 7 7.5 8.5 9 10 6.5 7.5 8.5 6 9.5 10 7 11.5 8 8.5 13 10 14 16 7 8.5 9 9.5 10.5 12.5 12.5 9 8.5 9 9.5 10 11 12 12.5 12 11 13 12.5 14 14 15 15 17 14 16 18 14 14 15 16.5 20 18.5 22 19 20.5 21 24 bulk L 4.6 4.6 4.6 4.6 4.6 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 7.2 10 10 10 10.3 10.3 10.3 10.3 13 13.5 13 13 13.5 13 13 13 13 18 19 18 19 18 19 18 19 18 18 19 18 26.5 26.5 26.5 28 26.5 28 26.5 26.5 26.5 28 Codes 0B 0C 0D 0E 0F 1A 1B 1C 1D 1E 1F 1G 1H 1I 1J 1K 1L 1M 1N 2A 2B 2C 2D 2E 2F 2G 3A FA 3C 3D FB 3F 3G 3H 3I 4B FC 4C FD 4D FE 4F FF 4H 4J FG 4M 5A 5B 5D FH 5F FI 5G 5H 5I FJ S 5000 5000 5000 5000 5000 5000 5000 5000 6000 4000 3500 4000 2500 2500 2500 2000 2000 1500 1000 5000 5000 4000 3500 3000 2000 1500 3000 3000 3000 3000 2000 3000 2400 2400 2000 2400 1000 2000 1000 1600 1000 1200 500 1200 900 500 1000 1200 1000 760 500 500 570* 594* 594* 561* 480* Moulded versions. Rights reserved to amend design data without prior notification. 01.19 * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D 2200 2500 - 2800 - 2000 2300 - 2300 - 1500 1800 - 1800 - 1200 1500 - 1500 - 900 1200 - 1200 - 2200 2500 - 2800 - 2000 2300 - 2300 - 1600 2000 - 2000 - 1300 1500 - 1500 - 1300 1500 - 1500 - 1100 1400 - 1400 - 1000 1200 - 1200 - 1000 1200 - 1200 - 800 1000 - 1000 - 700 1000 - 1000 - 700 950 - 1000 - 600 800 - 800 - 600 800 - 800 - 500 600 - 640 - - 2500 4400 2500 - - 2200 4300 2300 4150 - 1700 3200 1700 3100 - 1500 2900 1400 2700 - 1300 2500 1300 - - 1000 2200 1100 - - 900 1800 1000 - - 1100 2200 - 1900 - 900 1600 - 1450 - 900 1600 - 1450 - 900 1600 - 1400 - 700 1300 - 1200 - 700 1300 - 1200 - 550 1100 - 1000 - 550 1100 - 1000 - 400 800 - 740 - 600 1200 - 1150 - 600 1200 - 1200 - 500 1000 - 1000 - 500 1000 - 1000 - 450 900 - 850 - 450 900 - 850 - 400 800 - 740 - 400 800 - 740 - 350 700 - 650 - 350 700 - 650 - 300 650 - 590 - 300 600 - 540 - - 800 - 770 - - 700 - 640 - - 600 - 550 - - 500 - 480 - - 480 - 450 - - 420 - 380 - - 400 - 360 - - 400 - 360 - - 380 - 350 - - 350 - 310 ROLL 151 D Packing Quantities for Capacitors with Radial Pins in PCM 27.5 mm to 52.5 mm Size PCM pcs. per packing unit REEL AMMO P 360 P 500 340 x 340 490 x 370 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 H16.5 H18.5 N O F I H J A C B D - - 460/340* - 420 - - 380/280* - 350 - - 300 - 290 - - - - - 270 - 250 - - - - - - - - - - - - - - - - - - - - - - - - - - - ROLL bulk W 9 11 13 13 15 15 17 17 20 20 H 19 21 24 25 26 26 29 34.5 32 39.5 L 31.5 31.5 31.5 33 31.5 33 31.5 31.5 33 31.5 Codes 6A 6B 6D FK 6F FL 6G 6I FM 6J S 567* 459* 378* 405* 324* 324* 198* 198* 162* 162* 37.5 mm 9 11 13 15 17 19 20 24 31 35 40 19 22 24 26 29 32 39.5 45.5 46 50 55 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 41.5 7A 7B 7C 7D 7E 7F 7G 7H 7I 7J 7K 441* 357* 294* 252* 154* 140* 126* 112* 84* 35* 28* - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 48.5 mm 19 23 27 33 37 31 34 37.5 48 54 56 56 56 56 56 8D 8E 8H 8J 8L 120* 80* 84* 25* 25* - - - - - - - - - - - - - - - - - - - - - - - - - 45 45 50 55 65 57 57 57 57 57 9D 9E 9F 9H 9J 70* 60* 25* 20* 20* - - - - - 52.5 mm 25 30 35 45 45 - - - - - - - - - - 27.5 mm * for 2-inch transport pitches. * TPS (Tray-Packing-System). Plate versions may have different packing units. Samples and pre-production needs on request. Moulded versions. Rights reserved to amend design data without prior notification. 01.19 Updated data on www.wima.com 152 D WIMA Part Number System A WIMA part number consists of 18 digits and is composed as follows: Field 1 - 4: Type description Field 5 - 6: Rated voltage Field 7 - 10: Capacitance Field 11 - 12: Size and PCM Field 13 - 14: Version code (e.g. Snubber versions) Field 15: Capacitance tolerance Field 16: Packing Field 17 - 18: Pin length (untaped) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 M K S 2 C 0 2 1 0 0 1 A 0 0 M S S D 20 % bulk MKS 2 01.19 Type description: SMD-PET = SMDT SMD-PEN = SMDN SMD-PPS = SMDI FKP 02 = FKP0 MKS 02 = MKS0 FKS 2 = FKS2 FKP 2 = FKP2 FKS 3 = FKS3 FKP 3 = FKP 3 MKS 2 = MKS2 MKP 2 = MKP2 MKS 4 = MKS4 MKP 4C = MKPC MKP 4 = MKP4 MKP 10 = MKP1 FKP 1 = FKP1 MKP-X2 = MKX2 MKP-X1 R = MKX1 MKP-Y2 = MKY2 MP 3-X2 = MPX2 MP 3-X1 = MPX1 MP 3-Y2 = MPY2 MP 3R-Y2 = MPRY MKP 4F = MKPF Snubber MKP = SNMP Snubber FKP = SNFP GTO MKP = GTOM DC-LINK MKP 3 = DCP3 DC-LINK MKP 4 = DCP4 DC-LINK MKP 4S = DCPS DC-LINK MKP 5 = DCP5 DC-LINK MKP 6 = DCP6 DC-LINK HC = DCHC DC-LINK HY = DCHY 63 VDC Rated voltage: 50 VDC = B0 63 VDC = C0 100 VDC = D0 250 VDC = F0 400 VDC = G0 450 VDC = H0 520 VDC = H2 600 VDC = I0 630 VDC = J0 700 VDC = K0 800 VDC = L0 850 VDC = M0 900 VDC = N0 1000 VDC = O1 1100 VDC = P0 1200 VDC = Q0 1250 VDC = R0 1500 VDC = S0 1600 VDC = T0 2000 VDC = U0 2500 VDC = V0 3000 VDC = W0 4000 VDC = X0 6000 VDC = Y0 250 VAC = 0W 275 VAC = 1W 300 VAC = 2W 305 VAC = AW 350 VAC = BW 440 VAC = 4W 500 VAC = 5W ... 0.01 mF Capacitance: 22 pF = 0022 47 pF = 0047 100 pF = 0100 150 pF = 0150 220 pF = 0220 330 pF = 0330 470 pF = 0470 680 pF = 0680 1000 pF = 1100 1500 pF = 1150 2200 pF = 1220 3300 pF = 1330 4700 pF = 1470 6800 pF = 1680 0.01 mF = 2100 0.022 mF = 2220 0.047 mF = 2470 0.1 mF = 3100 0.22 mF = 3220 0.47 mF = 3470 = 4100 1 mF 2.2 mF = 4220 4.7 mF = 4470 = 5100 10 mF = 5220 22 mF = 5470 47 mF 100 mF = 6100 220 mF = 6220 1000 mF = 7100 1500 mF = 7150 ... 2.5 x 6.5 x 7.2 - Size: 4.8 x 3.3 x 3 Size 1812 = KA 4.8 x 3.3 x 4 Size 1812 = KB 5.7 x 5.1 x 3.5 Size 2220 = QA 5.7 x 5.1 x 4.5 Size 2220 = QB 7.2 x 6.1 x 3 Size 2824 = TA 7.2 x 6.1 x 5 Size 2824 = TB 10.2 x 7.6 x 5 Size 4030 = VA 12.7 x 10.2 x 6 Size 5040 = XA 15.3 x 13.7 x 7 Size 6054 = YA 2.5 x 7 x 4.6 PCM 2.5 = 0B 3 x 7.5 x 4.6 PCM 2.5 = 0C 2.5 x 6.5 x 7.2 PCM 5 = 1A 3 x 7.5 x 7.2 PCM 5 = 1B 2.5 x 7 x 10 PCM 7.5 = 2A 3 x 8.5 x 10 PCM 7.5 = 2B 3 x 9 x 13 PCM 10 = 3A 4 x 9 x 13 PCM 10 = 3C 5 x 11 x 18 PCM 15 = 4B 6 x 12.5 x 18 PCM 15 = 4C 5 x 14 x 26.5 PCM 22.5 = 5A 6 x 15 x 26.5 PCM 22.5 = 5B 9 x 19 x 31.5 PCM 27.5 = 6A 11 x21 x 31.5 PCM 27.5 = 6B 9 x 19 x 41.5 PCM 37.5 = 7A 11 x 22 x 41.5 PCM 37.5 = 7B 19 x 31 x 56 PCM 48.5 = 8D 25 x 45 x 57 PCM 52.5 = 9D ... Version code: Standard = Version A1 = Version A1.1.1 = Version A2 = ... 00 1A 1B 2A Tolerance: 20 % = 10 % = 5 % = 2.5 % = 1 % = ... 6 -2 M K J H E Packing: AMMO H16.5 340 x 340 AMMO H16.5 490 x 370 AMMO H18.5 340 x 340 AMMO H18.5 490 x 370 REEL H16.5 360 REEL H16.5 500 REEL H18.5 360 REEL H18.5 500 ROLL H16.5 ROLL H18.5 BLISTER W12 180 BLISTER W12 330 BLISTER W16 330 BLISTER W24 330 Bulk/TPS Standard ... =A =B =C =D =F =H =I =J =N =O =P =Q =R =T =S Pin length (untaped) 3.5 0.5 = C9 6 -2 = SD 16 1 = P1 ... Pin length (taped) none = 00 The data on this page is not complete and serves only to explain the part number system. Part number information is listed on the pages of the respective WIMA range. 147