S I G N A L T E C H N I K KombiSIGN 50, 70 and 71 Signals for combining - at the twist of a hand Kombi SIGN 50 Kombi SIGN 71 Kombi SIGN 70 Accessories for Signal Tower KombiSIGN 71 ORDER SPECIFICATIONS: Bulb BA 15 d, Total length max. 42 mm NEW 12 V, 5 Watt 955 840 34 24 V, 5 Watt 955 840 35 115 V, 5 Watt 955 840 57 230 V, 5 Watt 955 840 38 LED-Bulb BA 15d, Total length max. 42 mm 24 V Voltage Current consumption < 45 mA 115 V 230 V < 15 mA < 15 mA red 956 100 75 956 100 67 956 100 68 green 956 200 75 956 200 67 956 200 68 yellow 956 300 75 956 300 67 956 300 68 white 956 400 75 956 400 67 956 400 68 blue 956 500 75 956 500 67 956 500 68 Info transparencies available: neutral 975 840 49 number "5" 975 840 55 number "0" 975 840 50 number "6" 975 840 56 number "1" 975 840 51 number "7" 975 840 57 number "2" 975 840 52 number "8" 975 840 58 number "3" 975 840 53 number "9" 975 840 59 TECHNICAL DIAGRAMS see pages 26 + 27 CAGE CLAMP (R) 1 2 Insert screwdriver into opening as far as possible. 3 Open spring-loaded clamp with help of the screwdriver. Remove screwdriver - the conductor is firmly clamped. Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 11 S I G N A L T E C H N I K 840 Signal Tower KombiSIGN 70 * Signal tower system 70 mm o modular construction * 360 visibility * Wide range of optical and audible elements * Elements can be assembled as required TECHNICAL SPECIFICATIONS: Dimensions (Diameter x Height): Housing and accessories: Dome: Fixing: Base with tube (accessory) Socket: Connection: Element seal: Protection rating: Number of modules possible: Bracket (accessory) Terminal element: 70 mm x 30 mm Light element: 70 mm x 65 mm Audible element: 70 mm x 72 mm Polyamide, high impact, black Polycarbonate, transparent Base mounting Tube mounting, for tube o 25 mm Bracket mounting Bayonet, B 15 d, for bulb max. 7 W Screw M3 in terminal element Contact protection according to VDE Standard pre-mounted with each module Light elements: IP 54 Audible elements: IP 54 (Order no. 844 123 55 = IP 40) max. 5 / max. 10 elements with 2-sided bracket Permanent light element Bulbs not included in assembly 12 - 240 V Blinking light element 24 V 115 V 230 V Flashing light element Current consumption: reduced for AS-Interface: 12 V = 195 mA 24 V = 125 mA 80 mA 115 V 20 mA LED-Permanent light element Current consumption: Starting current: 24 V 45 mA < 0,5 A 115 V 25 mA 230 V 25 mA LED-Blinking light element Current consumption: Starting current: 24 V 40 mA < 0,5 A LED-Rotating light element Current consumption: Starting current: 24 V 70 mA < 0,5 A 230 V 15 mA TECHNICAL DIAGRAMS see page 25 ACCESSORIES see pages 26 + 27 840 842 2 843 5 2 +50C Tube mounting with Alu-tube 105 dB IP54 -20C 12 2 Ws Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K 840 Signal Tower KombiSIGN 70 ORDER SPECIFICATIONS OPTICAL ELEMENTS: Permanent / Blinking / Flashing light element Permanent light, clear with info n uratio Life d 0.000 h 10 up to Permanent light element red green yellow clear blue Blinking light element red green yellow clear blue Flashing light element12 V = red 842 100 green 842 200 yellow 842 300 clear 842 400 blue 842 500 LED-Permanent light element red green yellow clear blue LED-Blinking light element red green yellow clear blue LED-Rotating light element red green yellow clear blue 54 54 54 54 54 Flashing light el. 24 V = (ASI) 842 110 842 210 842 310 842 410 842 510 115 V 230 V 841 100 67 841 100 841 200 67 841 200 841 300 67 841 300 841 400 67 841 400 841 500 67 841 500 115 V 230 V 842 100 67 842 100 842 200 67 842 200 842 300 67 842 300 842 400 67 842 400 842 500 67 842 500 115 V 230 V 843 100 67 843 100 843 200 67 843 200 843 300 67 843 300 843 400 67 843 400 843 500 67 843 500 12-240 V 840 100 00 840 200 00 840 300 00 840 400 00 840 500 00 24 V 841 100 55 841 200 55 841 300 55 841 400 55 841 500 55 24 V = 842 100 55 842 200 55 842 300 55 842 400 55 842 500 55 24 V 843 100 55 843 200 55 843 300 55 843 400 55 843 500 55 24 V 843 110 55 843 210 55 843 310 55 843 410 55 843 510 55 24 V 843 130 55 843 230 55 843 330 55 843 430 55 843 530 55 55 55 55 55 55 68 68 68 68 68 68 68 68 68 68 68 68 68 68 68 LED element ORDER SPECIFICATIONS AUDIBLE ELEMENTS: Audible element Buzzer element 24 V 85 dB, 25 mA, IP 54, 844 118 55 continuous or pulsating tone Siren element 24 V = 105 dB, 100 mA, IP 40 844 123 55 continuous tone alternating Multi-functional Siren 24 V / 80 mA 100 dB, IP 54, 844 126 55 8 different tones, volume adjustable Multi-functional Siren, 24 V = with remote control 844 126 95 100 dB, 80 mA, IP 54, 7 different tones can be triggered remotely, volume adjustable Vocal element 24 V 844 900 55 115 V 844 118 67 230 V 844 118 68 115 V / 40 mA 230 V / 40 mA 844 126 67 844 126 68 ORDER SPECIFICATIONS TERMINAL ELEMENTS: Terminal element for tube mounting including cap 840 080 00 Terminal element for bracket or base mounting, including cap and seal 840 085 00 Terminal element with cap Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 13 S I G N A L T E C H N I K 840 Accessories for KombiSIGN 70 ORDER SPECIFICATIONS: Contact box for cable exit at side, with mounting material 975 840 01 Contact box with magnetic base and cable exit at side 975 840 04 Bracket for base mounting, with cable gland 960 000 01 Bracket for surface mounting, with cable gland 960 000 02 Bracket for 1-sided mounting incl. rubber seal 975 840 85 Bracket for 2-sided mounting incl. rubber seal 975 840 86 Tube o 25 mm, all anodized aluminium 14 100 mm long 975 845 10 250 mm long 975 840 25 400 mm long 975 840 40 800 mm long 975 840 80 Base for tube mounting o 25 mm, plastic incl. rubber seal 975 840 90 Base for tube mounting o 25 mm, metal incl. rubber seal 975 840 91 Base with integrated tube, o 25 mm, 110 mm long, plastic incl. rubber seal 975 840 10 Adapter for tube mounting o 25 mm / 1/2" screw 975 840 02 Cable gland for surface mounting M 16 x 1,5 960 000 04 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K 840 Accessories for KombiSIGN 70 ORDER SPECIFICATIONS: Bulb BA 15 d, Total length max. 42 mm NEW 12 V, 5 Watt 955 840 34 24 V, 5 Watt 955 840 35 115 V, 5 Watt 955 840 57 230 V, 5 Watt 955 840 38 LED-Bulb BA 15d, Total length max. 42 mm 115 V 230 V Current consumption < 45 mA < 15 mA < 15 mA red 956 100 75 956 100 67 956 100 68 green 956 200 75 956 200 67 956 200 68 yellow 956 300 75 956 300 67 956 300 68 white 956 400 75 956 400 67 956 400 68 blue 956 500 75 956 500 67 956 500 68 Voltage 24 V Info transparencies available: neutral 975 840 49 number "0" 975 840 50 number "1" 975 840 51 number "2" 975 840 52 number "3" 975 840 53 number "4" 975 840 54 number "5" 975 840 55 number "6" 975 840 56 number "7" 975 840 57 number "8" 975 840 58 number "9" 975 840 59 ORDER SPECIFICATIONS VOCAL ELEMENT: 24 V Vocal element 844 900 55 Recording station for vocal element, with microphone, 115 V ~ 844 901 67 Recording station, 230 V ~ (available on loan, please enquire) 844 901 68 TECHNICAL DIAGRAMS see pages 26 + 27 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 15 S I G N A L T E C H N I K 845 Signal Tower KombiSIGN 50 * Signal tower system 50 mm o modular construction * 360 visibility * Choice of optical and audible elements * Order of optical elements interchangeable as required * Tool-free changing of elements and bulbs TECHNICAL SPECIFICATIONS: Dimensions (Diameter x Height): Housing and accessories: Dome: Fixing: Base with tube (accessory) Socket: Connection: Protection rating: Number of modules possible: Terminal element: 52 mm x 16 mm Light element: 52 mm x 65 mm Audible element: 52 mm x 72 mm Polyamide, high impact, black Polycarbonate, transparent Base mounting Tube mounting, for tube o 25 mm Single hole mounting Bracket mounting Bayonet, B 15 d, for bulb max. 5 W Screwable connection M3, max. 2,5 mm2 Contact protection according to VDE Light elements: IP 54 Audible elements: IP 54 max. 4 Permanent light element Bulbs not included in assembly 12 - 240 V Blinking light element 24 V 115 V 230 V LED-Permanent light element Current consumption: Starting current: 24 V 115 V 45 mA 25 mA < 0,5 A at 24 V 230 V 25 mA Bracket (accessory) TECHNICAL DIAGRAMS see page 25 846 848 +50C Base mounting 16 80 dB IP54 3 2 -20C Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K 845 Signal Tower KombiSIGN 50 ORDER SPECIFICATIONS OPTICAL ELEMENTS: Permanent light element Permanent light element red green yellow clear blue 12-240 V 846 100 00 846 200 00 846 300 00 846 400 00 846 500 00 Blinking light element red green yellow clear blue 24 V 847 100 847 200 847 300 847 400 847 500 55 55 55 55 55 115 847 847 847 847 847 V 100 200 300 400 500 67 67 67 67 67 230 847 847 847 847 847 V 100 200 300 400 500 68 68 68 68 68 LED-Permanent light element red green yellow clear blue 24 V 848 100 848 200 848 300 848 400 848 500 55 55 55 55 55 115 848 848 848 848 848 V 100 200 300 400 500 67 67 67 67 67 230 848 848 848 848 848 V 100 200 300 400 500 68 68 68 68 68 Blinking light element n uratio Life d 0.000 h 10 up to ORDER SPECIFICATIONS AUDIBLE ELEMENTS: Buzzer element 80 dB, 24 V , max. 25 mA, IP 54, continuous or pulsating tone, adjustable 24 V 849 000 75 115 V 849 000 77 230 V 849 000 68 ORDER SPECIFICATIONS TERMINAL ELEMENT: LED element Terminal element 845 000 00 for base mounting, tube mounting, single hole and bracket mounting, including cap ACCESSORIES see page 26 + 27 Audible element Terminal element with cap Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 17 S I G N A L T E C H N I K 845 Accessories KombiSIGN 50 ORDER SPECIFICATIONS: Contact box for cable exit at side, with mounting material 975 840 01 Contact box with magnetic base and cable exit at side 975 840 04 Bracket for surface mounting, with cable gland 960 000 01 Bracket for tube mounting 975 845 02 Tube o 25 mm, all anodized aluminium 100 mm long 975 845 10 250 mm long 975 840 25 400 mm long 975 840 40 800 mm long 975 840 80 Base for tube mounting o 25 mm, plastic incl. rubber seal 975 840 90 Base for tube mounting o 25 mm, metal incl. rubber seal 975 840 91 Base for surface mounting 975 845 01 Adapter for single hole mounting incl. rubber seal 975 845 03 Bulb BA 15 d, Total length max. 42 mm 12 V, 24 V, 115 V, 230 V, NEW 5 5 5 5 Watt Watt Watt Watt 955 955 955 955 840 840 840 840 34 35 57 38 LED-Bulb BA 15d, Total length max. 42 mm Voltage Current consumption red green yellow white blue 24 V < 45 mA 956 100 956 200 956 300 956 400 956 500 75 75 75 75 75 115 V < 15 mA 956 100 956 200 956 300 956 400 956 500 67 67 67 67 67 230 V < 15 mA 956 100 956 200 956 300 956 400 956 500 68 68 68 68 68 TECHNICAL DIAGRAMS see pages 26 + 27 18 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K Signal Tower with AS-Interface Element Signal towers KombiSIGN 50, 70 and 71 with AS-interface element are capable of total communication: By simple integration of an AS-interface element the actuators are NTERFACE connected to the networking system actuator-sensor-interface - this considerably reduces complex wiring. This element is to be mounted as the lowermost element in the signal tower just like a light element. TECHNICAL SPECIFICATIONS: AS-Interface Element 1) AS-Interface Element with additional external voltage1) 2) Number of signal elements max. 4 max. 4 Type of signal elements Flashing light elements Permanent light elements LED elements Flashing light elements1) Buzzer elements LED elements Siren elements Buzzer elements (the total consumption Siren elements1) of the single elements must not exceed 200 mA) IO-Code 8 8 ID-Code F F Power supply through bus conduction through bus conduction Operaring voltage 18,5 V ... 31,6 V 18,5 V ... 31,6 V Current consumption 210 mA 75 mA1) / 50 mA2) Reverse battery protection integrated integrated Watchdog integrated integrated Terminals 4, electronic 4, relays On-load voltage through bus conduction additional external 10 V...120 V=1) voltage: 10 V...30 V = 2) 10 V...230 V ~ 1) Current carrying cap. Imax 200 mA 1,5 A Short current-/overload pro. integrated fuse M 1,6 A valid for KombiSIGN 70 and 71 / 2) valid for KombiSIGN 50 ORDER SPECIFICATIONS AS-INTERFACE ELEMENTS KOMBISIGN 70 + 71: KombiSIGN 70 KombiSIGN 71 AS-Interface Element 840 800 55 646 800 55 AS-Interface Element with add. external voltage 840 800 68 646 800 68 ORDER SPECIFICATIONS AS-INTERFACE ELEMENT KOMBISIGN 50: AS-Interface Element with add. external voltage 845 800 68 TECHNICAL DIAGRAMS see pages 24 + 25 + 26 840/845 646 +50C IP54 IP65 -20C Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 19 S I G N A L T E C H N I K Summary of KombiSIGN Accessories KombiSIGN 50 KombiSIGN 50, 70 and 71 Order no. 975 845 01 Order no. 975 840 01 Order no. 975 845 02 Order no. 975 845 03 Base for surface mounting and tube mounting Contact box for cable exit at side, with mounting material Bracket for tube mounting Order no.. 960 000 01 Adapter for single hole mounting LED-Bulb BA 15d Total length max. 42 mm Voltage Current consumption Order no. 975 840 04 Contact box with magnetic base and cable exit at side Bracket for base mounting, including cable gland M 16 x 1,5 24 V 115 V 230 V < 45 mA < 15 mA < 15 mA red 956 100 75 956 100 67 956 100 68 green 956 200 75 956 200 67 956 200 68 yellow 956 300 75 956 300 67 956 300 68 white 956 400 75 956 400 67 956 400 68 blue 956 500 75 956 500 67 956 500 68 NEW Bulb BA 15 d, Total length max. 42 mm 955 840 34 20 12 V, 5 Watt 955 840 35 24 V, 5 Watt 955 840 57 115 V, 5 Watt 955 840 38 230 V, 5 Watt TECHNICAL DIAGRAMS see pages 26 + 27 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K Summary of KombiSIGN Accessories KombiSIGN 70 and 71 Order no. 975 840 90 Order no. 975 840 91 Base for tube mounting o 25 mm, plastic Base for tube o 25 mm, metal Order no. 975 845 10 Tube o 25 mm, all anodized aluminium 100 mm long 975 840 25 250 mm long 975 840 40 400 mm long 975 840 80 800 mm long Order no. 975 840 85 Order no. 975 840 10 Bracket for 1-sided mounting Base with integrated tube, o 25 mm, 110 mm long, plastic Order no. 960 000 02 Order no. 975 840 86 Order no. 975 840 02 Bracket for 2-sided mounting Adapter for tube mounting o 25 mm / 1/2" screw Order no. Bracket for surface mounting 960 000 04 Cable gland for surface including cable gland mounting, M 16 x1,5 M 16 x 1,5 Order no. Info transparencies: 975 840 49 neutral 975 840 50 number 975 840 51 number 975 840 52 number 975 840 53 number "0" "1" "2" "3" Order no. 975 840 54 975 840 55 975 840 56 975 840 57 975 840 58 975 840 59 number number number number number number "4" "5" "6" "7" "8" "9" TECHNICAL DIAGRAMS see pages 26 + 27 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 21 S I G N A L T E C H N I K Interface Box for KombiSIGN 50, 70 and 71 * Direct triggering via PC * Triggering of four independent signal tower modules * Software included in delivery TECHNICAL SPECIFICATIONS: Dimensions of interface box (L x W x H): 120 x 65 x 40 mm Drive: up to 4 signal elements 24 V via PC Interface: Serial RS 232 Connection: COM with Sub-D 9-pin Assembly: Interface Box Network appliance 24 V Software: Driver for Labview Working temperature: - 20 C bis + 50 C ORDER SPECIFICATIONS: Interface Box NEW 960 000 06 TECHNICAL DIAGRAMS see page 116 +50C 160 g -20C Indication Board for KombiSIGN 50, 70 and 71 * Indication board for one to five modules * Simple mounting onto signal tower tube * Ample space for written information * Simply break off unwanted segments TECHNICAL SPECIFICATIONS: Dimensions of indication board (W x H): 153 x 345 mm Surface area per section (W x H): ca. 140 x 50 mm Material: PMMA Assembly: Indication board (5 sections) including mounting material Mounting: Fixing only possible on 25 mm diameter tube ORDER SPECIFICATIONS: NEW Indication Board 960 000 05 TECHNICAL DIAGRAMS see page 26 22 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K 840 Vocal element for KombiSIGN 70 A vocal element is also available as a further audible signal element. Up to 15 different messages can be recorded and recalled. Volume can be adjusted using a potentiometer within a range at 0 - 88 dB. A distribution voltage of 24 V = is necessary. Total recording time available is 60 seconds. The drive of the individual messages uses 24 V =, 4 Bit parallel. Up to 3 optical signal elements can be integrated in addition to the vocal element in any one signal tower. The number of messages is then limited to one. The recording of messages is carried out using a separate recording station. TECHNICAL SPECIFICATIONS: Dimensions (Diameter x Height): Housing: Protection rating: Operating voltage: Current consumption: Volume: Number of texts: Total recording time: Drive: Driving voltage: 70 x 69 mm Polyamide, high impact, black IP 53 24 V = (15 - 30 V =) 350 mA 0 - 88 dB (1m) adjustable max. 15 60 seconds 4 Bit parallel + 24 V ORDER SPECIFICATIONS VOCAL ELEMENT: 24 V Vocal element 844 900 55 Recording station for vocal element, with microphone, 115 V ~ 844 901 67 Recording station, 230 V ~ (available on loan, please enquire) 844 901 68 TECHNICAL DIAGRAMS see page 25 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 23 S I G N A L T E C H N I K Technical Diagrams KombiSIGN 71 640 640 o 70 16 o 70 25 26,5 o 69 o15 o17,7 640 8X0 00 Terminal element for tube mounting 124 86 112 180 236 292 348 56 408 o25 o 70 640 16 o 70 26,5 25 o 69 7 o15 o17,7 o 25 rubber seal o 4,2 21,5 640 8X0 00 24 18 3 Terminal element for base/bracket mounting Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K Technical Diagrams KombiSIGN 70 840 KombiSIGN 50 845 840 o 70 o 70 13 o 52 25 30 o 68,5 o 15 o 17,7 85 13 128 o 70 133 117 184 840 115 371 243 Terminal element for tube mounting 188 840 080 00 240 56 296 352 298 353 410 o 25 o 68,5 rubber seal 7 30 o 70 25 1,5 o 70 o 15 o 17,7 o 25 845 25 o 4,2 21.5 18,75 31,4 21,3 rubber seal o 21,6 1,75 o 52 840 085 00 Terminal element for base/bracket mounting 845 000 00 Terminal element 69 840 o 70 844 900 55 Vocal element Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 25 S I G N A L T E C H N I K Technical Diagrams Accessories 55 87,5 25 R 1/2" 975 840 02 Adapter ca. 345 snap off grooves 43,5 38 M16 x 1,5 19 32 46 18 9 o 6,2 52,5 975 840 04 Adapter with magnetic base o 25 ca. 55 o 70 36 o1 2 ca. 188 top view without signal tower Bracket 110 960 000 01 960 000 05 Indication board o 10,5 o 5,5 rubber seal 40 1,5 76,5 9 o 6,2 18 38 55 socket power supply 120 65 19 36 o1 2 o 55 49 o 54 5 4 3 2 1 RS232 5 pin terminal strip to fit the terminal of a 4-phase signal tower Base with tube sketch without cap o 70 960 000 06 960 000 02 o 70 975 840 10 Interface Box Bracket o 10,5 o 1,5 960 000 04 PG screw for base mounting 54 rubber seal 15 28,5 M16 x 1,5 975 840 01 26 o 54 o o 5,5 M 16 X 1,5 rubber seal 1,5 4, 4 o 43 max. 4,5 o 5,5 15 o 70 o 70 Adapter box 975 840 85 Bracket Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K Technical Diagrams Accessories o 70 1.5 o 70 o 5,5 37 o 70 o 5,5 o 10,5 rubber seal 1,5 rubber seal o 54 54 975 845 01 Base for surface mounting 975 840 86 2-sided bracket o 21,7 17 37 o 10,5 o 5,5 cable entry o 70 6 o6 ,5 18 58 1,5 rubber seal 38 o 54 975 840 90 51,5 Base for tube, plastic 36 o 35 50 o 25,3 31 o 9,5 975 845 02 5,5 Bracket o 73,5 40 1,5 rubber seal 20 o 54 M18 O-Ring seal lock washer 975 845 03 975 840 91 Base for tube, metal Adapter for single hole mounting Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 27 S I G N A L T E C H N I K WERMA Product Groups Signal Towers Optical-Audible Signal Devices Optical Signal Devices Audible Signal Devices Ex-Signal Devices The WERMA Product Range Signal Towers Optical Signal Devices Optical-Audible Signal Devices Audible Signal Devices Ex-Signal Devices S I G N A L T E C H N I K WERMA Signaltechnik GmbH + Co. 78604 Rietheim-Weilheim Phone +49 74 24 95 57 0 Fax +49 74 24 95 57 44 www.werma.de info@ werma.de 09/01 * 990 840 02 * E Please ask for our detailed catalogue. KombiSIGN 50 KombiSIGN 70 Protection rating IP 54 Protection rating IP 54 Slim design modular Signal Tower system with 50 mm diameter. For use in normal conditions For use on smaller machines. Series 840 Not compatible with KombiSIGN 71 Terminal element Terminal element 50 mm Screwable connection Screwable connection Optically different to KombiSIGN 71 due to: Practical bayonet fixing system. Tool free bulb change. *Flat packing *No phase on dome edge *Conical terminal element 2 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K KombiSIGN 71 NEW Protection rating IP 65 For use in extreme conditions Series 640 70 mm 70 mm Not compatible with KombiSIGN 70 Terminal elements Either: improved screwable connection see page 11 Or: terminal element with CAGE CLAMP(R) technology Optically different to KombiSIGN 70 due to: *O-Ring seal *Phase in inside of dome *Cylindrical terminal element CAGE CLAMP(R) is a registered trademark of WAGO Kontakttechnik GmbH. Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 3 S I G N A L T E C H N I K KombiSIGN Signal Towers Complete Programme The KombiSIGN programme offers the customer the most diverse beacon elements in all voltages; these can be combined as required. All in all, KombiSIGN offers a solution for every signalling field. PERMANENT LIGHT ELEMENTS: LED PERMANENT LIGHT: With socket B 15d for filament bulbs and LEDs. LED permanent light elements with integral Chip-On-Board technology have a high light intensity and durability. FLASH ELEMENTS: LED ELEMENTS: Flash elements can be combined as required with other signal elements within a signal tower. For Blinking and Rotating light - high light intensity and durability. n inatio comb d e l b i n a Flex ts. tical of op al elemen n le sig audib Comprehensive range of audible elements KombiSIGN audible elements do not require an open sound outlet. This ensures the high protection rating of IP 54 or IP 65 - even at a volume of up to 100 dB . VOCAL ELEMENT: AUDIBLE ELEMENTS: Up to 15 different texts or melodies can be recorded or played with the vocal element. The KombiSIGN programme offers a huge selection of audible signal elements for each application. 4 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K KombiSIGN Signal Towers Bayonet screw WERMA is the first signal beacon manufacturer with a quick screw system. The bayonet screw makes it possible to connect elements both mechanically and electrically in seconds and the exchange of elements or bulb changes are made quick and easy as no tools are required. SIMPLE OPERATION Great diversity of accessories A huge range of accessories enables the customer to put together signal towers which are both aesthetically pleasing and competitively priced for all fields of use. IP 54 IP 65 Modular Signal Tower system in different sizes KombiSIGN is the only signal tower system with bayonet screw in different sizes. The modular assembly makes it easy to find a fitting combination for every application. Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 5 S I G N A L T E C H N I K LED with Chip-On-Board technology (COB) WERMA Signal Towers with LED-COB The need for high operational safety has increased the importance of light diodes in signal technology. WERMA has adopted a totally new and revolutionary approach with the introduction of Chip-On-Board technology. This involves bonding LEDs with 180 visibility directly onto a gold-plated printed circuit board. STRIP WITH LED-COB LED chip-on-board technology involves setting the individual LED chips directly onto the gold-plated contact surface of the printed circuit board with the aid of an automatic bonding system. Bonding follows using a gold wire to the antipole. The colours clear, green and blue have a higher light intensity than red and yellow; here only four of the six gold surfaces are fitted with LED chips. Bubble Gold Wire Silver Epoxy Adhesive PCB Gold Surface LED Chip Cathode, Anode OUTSTANDING FEATURES OF LED-COB: * * * * 6 Extreme durability Low current consumption High resilience Resistance to vibration and mechanical wear and tear Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K LED with Chip-On-Board technology (COB) Two models with COB technology are available: As LED bulb and as an integral element. 1 LED BULB BA 15 d The compact construction form has made it possible to produce an independent LED bulb with a BA 15d dome. Bulb 956 can be inserted into permanent beacons with a B 15d socket instead of a conventional light bulb. * High light intensity with 360 visibility * High light efficiency with optimised prism form * Manual grip facility on dome LED BULB 956 IN PLACE OF FILAMENT BULB LED Bulb 956 can be inserted into permanent light elements with BA 15d socket instead of a conventional bulb. OPTIMISED FOR USE IN WERMA SIGNAL TOWERS LED Bulb 956 is optimised for use in WERMA signal towers. 2 COB-STRIPS IN LED PERMANENT LIGHT ELEMENT An LED-COB strip is integrated into the housing of LED permanent light. * Life duration of up to 100.000 hours * 360 visibility * Protective switch for current limitation and surge voltage Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 7 S I G N A L T E C H N I K 640 Signal Tower KombiSIGN 71 * High protection rating IP 65 * Signal tower system 70 mm o modular construction * 360 visibility * Flexible combination of optical and audible devices TECHNICAL SPECIFICATIONS: Dimensions (Diameter x Height): Housing and accessories: Dome: Fixing: NEW Socket: Connection: Bracket (accessory) Element seal: Protection rating: Number of modules possible: NEW Terminal element: 70 mm x 26,5 mm Light element: 70 mm x 65 mm Audible element: 70 mm x 72 mm Polyamide, high impact, black Polycarbonate, transparent Base mounting Tube mounting, for tube o 25 mm Bracket mounting Bayonet, B 15 d, for bulb max. 7 W CAGE CLAMP(R) technology up to 2,5 mm2 or screwable connection M3 Contact protection according to VDE Standard pre-mounted with each module Light elements: IP 65 Audible elements: IP 65 (Order no. 645 830 55 = IP 40) max. 5 / max. 10 elements with 2-sided bracket Permanent light element Bulbs not included in assembly 12 - 240 V Blinking light element 24 V 115 V 230 V Flashing light element Current consumption: reduced for AS-Interface: 12 V = 195 mA 24 V = 125 mA 80 mA 115 V 20 mA LED-Permanent light element Current consumption: Starting current: 24 V 45 mA < 0,5 A 115 V 25 mA 230 V 25 mA LED-Blinking light element Current consumption: Starting current: 24 V 40 mA < 0,5 A LED-Rotating light element Current consumption: Starting current: 24 V 70 mA < 0,5 A 230 V 15 mA TECHNICAL DIAGRAMS see page 24 Base with tube (accessory) ACCESSORIES see pages 26 + 27 641 643 644 +50C 2 5 2 105 dB IP65 -20C 8 2 Ws Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K 640 Signal Tower KombiSIGN 71 ORDER SPECIFICATIONS OPTICAL ELEMENTS: Permanent / Blinking / Flashing light element Permanent light, clear with text n uratio Life d 0.000 h 10 up to LED element Permanent light element red green yellow clear blue 12-240 V 641 100 00 641 200 00 641 300 00 641 400 00 641 500 00 Blinking light element red green yellow clear blue 24 V 642 100 642 200 642 300 642 400 642 500 75 75 75 75 75 115 642 642 642 642 642 V 100 200 300 400 500 77 77 77 77 77 230 642 642 642 642 642 V 100 200 300 400 500 78 78 78 78 78 Flashing light element red green yellow clear blue 24 V = 643 100 643 200 643 300 643 400 643 500 55 55 55 55 55 115 643 643 643 643 643 V 100 200 300 400 500 67 67 67 67 67 230 643 643 643 643 643 V 100 200 300 400 500 68 68 68 68 68 LED-Permanent light element red green yellow clear blue 24 V 644 100 644 200 644 300 644 400 644 500 75 75 75 75 75 115 644 644 644 644 644 V 100 200 300 400 500 67 67 67 67 67 230 644 644 644 644 644 V 100 200 300 400 500 68 68 68 68 68 LED-Blinking light element red green yellow clear blue 24 V 644 110 644 210 644 310 644 410 644 510 75 75 75 75 75 LED-Rotating light element red green yellow clear blue 24 V 644 130 644 230 644 330 644 430 644 530 75 75 75 75 75 ORDER SPECIFICATIONS AUDIBLE ELEMENTS: Audible element Buzzer element 24 V 115 V 85 dB, 25 mA, IP 65, 645 800 75 645 800 77 continuous or pulsating tone Siren element 24 V = 105 dB, 100 mA, IP 40 645 830 55 continuous tone alternating 115 V / 40 mA Multi-functional Siren 24 V / 80 mA 645 820 67 100 dB, 40 mA, IP 65, 8 different 645 820 75 tones, volume adjustable Multi-functional Siren, 24 V = with remote control 645 850 55 100 dB, 80 mA, IP 65, 7 different tones can be triggered remotely, volume adjustable 230 V 645 800 68 230 V / 40 mA 645 820 68 ORDER SPECIFICATIONS TERMINAL ELEMENTS: Terminal element with cap Terminal element for tube mounting including cap Terminal element for bracket or base mounting including cap and seal CAGE CLAMP(R) 640 810 00 Screw connection 640 830 00 640 800 00 640 820 00 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 9 S I G N A L T E C H N I K Accessories for Signal Tower KombiSIGN 71 ORDER SPECIFICATIONS: Contact box for cable exit at side, with mounting material 975 840 01 Contact box with magnetic base and cable exit at side 975 840 04 Bracket for base mounting, with cable gland 960 000 01 Bracket for surface mounting, with cable gland 960 000 02 Bracket for 1-sided mounting incl. rubber seal 975 840 85 Bracket for 2-sided mounting incl. rubber seal 975 840 86 Tube o 25 mm, all anodized aluminium 100 mm long 975 845 10 250 mm long 975 840 25 400 mm long 975 840 40 800 mm long 975 840 80 Base for tube mounting o 25 mm, plastic incl. rubber seal 975 840 90 Base for tube mounting o 25 mm, metal incl. rubber seal 975 840 91 Base with integrated tube, o 25 mm, 110 mm long, plastic incl. rubber seal 975 840 10 Adapter for tube mounting o 25 mm / 1/2" screw 975 840 02 960 000 04 Cable gland for surface mounting M 16 x 1,5 10 Phone +49 74 24 / 95 57 0 . Fax +49 74 24 / 95 57 44 S I G N A L T E C H N I K