[AK4490] AK4490 Premium 32-Bit 2ch DAC 1. General Description AK4490 is a new generation Premium 32-bit 2ch DAC with new technologies, achieving industry's leading level low distortion characteristics and wide dynamic range. The AK4490 integrates a newly developed switched capacitor filter "OSR Doubler", making it capable of supporting wide range signals and achieving low out-of-band noise while realizing low power consumption. Moreover, the AK4490 has five types of 32-bit digital filters, realizing simple and flexible sound tuning in wide range of applications. The AK4490 accepts up to 768kHz PCM data and 11.2MHz DSD data, ideal for a high-resolution audio source playback that are becoming widespread in network audios, USB-DACs and Car Audio Systems. Application: AV Receivers, CD/SACD player, Network Audios, USB DACs, USB Headphones, Sound Plates/Bars, Car Audios, Automotive External Amplifiers, Measurement Equipment, Control Systems, Public Audios (PA), Smart Cellular Phones, IC-Recorders, Bluetooth Headphones, HD Audio/Voice Conference Systems 2. Features 256x Over sampling Sampling Rate: 30kHz 768kHz 32-bit 8x Digital Filter - Ripple: 0.005dB, Attenuation: 100dB - Short Delay Sharp Roll-off, GD=6.25/fs - Short Delay Slow Roll-off, GD=5.3/fs - Sharp Roll-off - Slow Roll-off - Super Slow Roll-off High Tolerance to Clock Jitter Low Distortion Differential Output 2.8MHz, 5.6MHz and 11.2MHz DSD Input Support - Filter (fc=50kHz, fc=150kHz, 2.8MHz mode) Digital De-emphasis for 32, 44.1, 48kHz sampling Soft Mute Digital Attenuator (255 levels and 0.5dB step) Mono Mode External Digital Filter Mode THD+N: -112dB DR, S/N: 120dB (Mono mode: 123dB) I/F Format: 24/32bit MSB justified, 16/20/24/32bit LSB justified, I2S, DSD Master Clock: 30kHz ~ 32kHz: 1152fs 30kHz ~ 54kHz: 512fs or 768fs 30kHz ~ 108kHz: 256fs or 384fs 108kHz ~ 216kHz: 128fs or 192fs ~ 384kHz: 64fs or 128fs ~ 768kHz: 64fs Power Supply: DVDD=AVDD=3.0 3.6V, VDD1/2=4.75 7.2V Digital Input Level: CMOS Package: 48-pin LQFP MS1648-E-03 2014/11 -1- [AK4490] 3. Table of Contents 1. General Description ....................................................................................................................................... 1 2. Features.......................................................................................................................................................... 1 3. Table of Contents .......................................................................................................................................... 2 4. Block Diagram............................................................................................................................................... 4 5. Pin Configurations and Functions ................................................................................................................. 5 Ordering Guide ......................................................................................................................................... 5 Pin Layout ................................................................................................................................................ 5 Pin Functions ............................................................................................................................................ 6 Handling of Unused Pin ........................................................................................................................... 8 6. Absolute Maximum Ratings .......................................................................................................................... 9 7. Recommended Operating Conditions ............................................................................................................ 9 8. Electrical Characteristics ............................................................................................................................. 10 Analog Characteristics............................................................................................................................ 10 Sharp Roll-Off Filter Characteristics (fs=44.1kHz) ............................................................................... 11 Sharp Roll-Off Filter Characteristics (fs=96kHz) .................................................................................. 11 Sharp Roll-Off Filter Characteristics (fs=192kHz) ................................................................................ 11 Short Delay Sharp Roll-Off Filter Characteristics (fs=44.1kHz) ........................................................... 13 Short Delay Sharp Roll-Off Filter Characteristics (fs=96kHz) .............................................................. 13 Short Delay Sharp Roll-Off Filter Characteristics (fs=192kHz) ............................................................ 13 Slow Roll-Off Filter Characteristics (fs=44.1kHz) ................................................................................ 15 Slow Roll-Off Filter Characteristics (fs=96kHz) ................................................................................... 15 Slow Roll-Off Filter Characteristics (fs=192kHz) ................................................................................. 15 Short Delay Slow Roll-Off Filter Characteristics (fs=44.1kHz) ............................................................ 17 Short Delay Slow Roll-Off Filter Characteristics (fs=96kHz) ............................................................... 17 Short Delay Slow Roll-Off Filter Characteristics (fs=192kHz) ............................................................. 17 DSD Mode Characteristics ..................................................................................................................... 19 DC Characteristics .................................................................................................................................. 19 Switching Characteristics ....................................................................................................................... 20 Timing Diagram ..................................................................................................................................... 22 9. Functional Descriptions ............................................................................................................................... 27 D/A Conversion Mode ........................................................................................................................... 27 System Clock .......................................................................................................................................... 27 Audio Interface Format .......................................................................................................................... 34 D/A Conversion Mode Switching Timing.............................................................................................. 39 De-emphasis Filter.................................................................................................................................. 40 Output Volume (PCM, DSD) ................................................................................................................. 40 Zero Detection (PCM, DSD) .................................................................................................................. 41 Mono Output (PCM, DSD, EX DF I/F) ................................................................................................. 41 Sound Quality Control (PCM, DSD, Ex DF I/F).................................................................................... 41 Soft Mute Operation (PCM, DSD) ......................................................................................................... 43 System Reset .......................................................................................................................................... 43 Power ON/OFF timing ........................................................................................................................... 44 Reset Function ........................................................................................................................................ 45 Synchronize Function ............................................................................................................................. 47 Register Control Interface ...................................................................................................................... 49 Register Map .......................................................................................................................................... 54 Register Definitions ................................................................................................................................ 54 MS1648-E-03 2014/11 -2- [AK4490] 10. Recommended External Circuits ............................................................................................................... 60 11. Package ...................................................................................................................................................... 64 Outline Dimensions ................................................................................................................................ 64 Material & Lead finish ........................................................................................................................... 64 Marking .................................................................................................................................................. 65 12. Revision History ........................................................................................................................................ 65 IMPORTANT NOTICE .................................................................................................................................. 68 MS1648-E-03 2014/11 -3- [AK4490] 4. Block Diagram DVDD DVSS PDN AVDD AVSS VSSL BICK/DCLK/BCK LRCK/DSDR/DINR VDDL Interpolator PCM Data Interface SCF AOUTLN SDATA/DSDL/DINL DSD Data Interface AOUTLP Normal path DSDD bit "0" Modulator DATT Soft Mute Bias Vref Volume bypass DSDD bit "1" External DF Interface SCF VCML VREFHL VREFLL VREFLR VREFLL VCMR AOUTRP AOUTRN WCK SSLOW CSN/SMUTE CCLK/DEM0 Clock Divider Control Register VDDR VSSR CDTI/DEM1 CAD1/ACKS PSN DZFL/DIF0 DZFR/DIF1 CAD0/DIF2 MCLK Block Diagram MS1648-E-03 2014/11 -4- [AK4490] 5. Pin Configurations and Functions Ordering Guide 40 +85C 48pin LQFP (0.5mm pitch) Evaluation Board for AK4490 AK4490EQ AKD4490 AOUTLP AOUTLN VDDL VDDL VSSL VSSL VSSR VSSR VDDR VDDR AOUTRN AOUTRP 36 35 34 33 32 31 30 29 28 27 26 25 Pin Layout NC 37 24 NC VCML 38 23 VCMR VREFLL 39 22 VREFLR VREFLL 40 21 VREFLR VREFHL 41 20 VREFHR VREFHL 42 19 VREFHR NC 43 18 AVDD1 44 17 NC OUTRP ACKS/CAD1 AVSS 1 MCLK 45 16 DEM1 46 15 DEM0 DVSS 47 14 I2C DVDD 48 13 PSN AK4490 1 2 3 4 5 6 7 8 9 10 11 12 NC PDN BICK/DCLK/BCK SDATA/DSDL/DINL LRCK/DSDR/DINR SSLOW/WCK SMUTE/CSN SD/CCLK/SCL SLOW/CDTI/SDA DIF0/DZFL/TSTO DIF1/DZFR/TSTO DIF2/CAD0 Top View MS1648-E-03 2014/11 -5- [AK4490] Pin Functions No. 1 2 3 4 5 6 7 8 9 10 11 12 Pin Name NC I/O - PDN I BICK DCLK BCK SDATA DSDL DINL LRCK DSDR DINR SSLOW WCK I I I I I I I I I I I SMUTE I CSN SD CCLK SCL SLOW CDTI SDA DIF0 DZFL DIF1 DZFR DIF2 CAD0 I I I I I I I/O I O I O I I 13 PSN I 14 I2C I Function No internal bonding. Connect to GND. Power-Down Mode Pin When at "L", the AK4490 is in power-down mode and is held in reset.The AK4490 must always be reset upon power-up. Audio Serial Data Clock Pin in PCM Mode DSD Clock Pin in DSD Mode Audio Serial Data Clock Pin Audio Serial Data Input Pin in PCM Mode DSD Lch Data Input Pin in DSD Mode Lch Audio Serial Data Input Pin L/R Clock Pin in PCM Mode DSD Rch Data Input Pin in DSD Mode in Serial Control Mode Rch Audio Serial Data Input Pin in Serial Control Mode Digital Filter Setting in Parallel Control Mode Word Clock input pin in Serial Control Mode Soft Mute Pin in Parallel Control Mode When this pin is changed to "H", soft mute cycle is initiated. When returning "L", the output mute releases. Chip Select Pin in Serial Control Mode, I2C= "L" Digital Filter Setting Pin in Parallel Control Mode Control Data Clock Pin in Serial Control Mode, I2C= "L" Control Data Clock Input Pin in Serial Control Mode, I2C= "H" Digital Filter Setting Pin in Parallel Control Mode Control Data Input Pin in Serial Control Mode, I2C= "L" I2C="H": Control Data Input Pin in Serial Control Mode, I2C= "H" Digital Input Format 0 Pin in PCM Mode Lch Zero Input Detect Pin in Serial Control Mode Digital Input Format 1 Pin in PCM Mode Rch Zero Input Detect Pin in Serial Control Mode Digital Input Format 2 Pin in PCM Control Mode Chip Address 0 Pin in Serial Control Mode Parallel or Serial Select Pin (Internal pull-up pin) "L": Serial Control Mode, "H": Parallel Control Mode I2C mode select pin in Serial mode (Internal pull-down pin) 15 DEM0 I De-emphasis Enable 0 Pin in Parallel Control Mode (Internal pull-up pin) Note: All input pins except internal pull-up/down pins must not be left floating. MS1648-E-03 2014/11 -6- [AK4490] 16 18 DEM1 ACKS CAD1 NC I I I - De-emphasis Enable 1 Pin in Parallel Control Mode (Internal pull-down pin) Master Clock Auto Setting Mode Pin in Parallel Mode (Internal pull-down pin) Chip Address 1 Pin in Serial Control Mode No internal bonding. Connect to GND. 19 VREFHR I Rch High Level Voltage Reference Input Pin 20 21 22 VREFHR VREFLR VREFLR I I I 23 VCMR - 24 25 26 27 28 29 30 31 32 33 34 35 36 NC AOUTRP AOUTRN VDDR VDDR VSSR VSSR VSSL VSSL VDDL VDDL AOUTLN AOUTLP O O - 37 NC - 38 VCML - Rch High Level Voltage Reference Input Pin Rch Low Level Voltage Reference Input Pin Rch Low Level Voltage Reference Input Pin Right channel Common Voltage Pin, Normally connected to VREFLR with a 10uF electrolytic cap. No internal bonding. Connect to GND. Rch Positive Analog Output Pin Rch Negative Analog Output Pin Rch Analog Power Supply Pin, 4.75 7.2V Rch Analog Power Supply Pin, 4.75 7.2V Ground Pin Ground Pin Ground Pin Ground Pin Lch Analog Power Supply Pin, 4.75 7.2V Lch Analog Power Supply Pin, 4.75 7.2V Lch Negative Analog Output Pin Lch Positive Analog Output Pin No internal bonding. Connect to GND. Left channel Common Voltage Pin, Normally connected to VREFLL with a 10uF electrolytic cap. 39 VREFLL I 40 41 42 VREFLL VREFHL VREFHL I I I 17 O O Lch Low Level Voltage Reference Input Pin Lch Low Level Voltage Reference Input Pin Lch High Level Voltage Reference Input Pin Lch High Level Voltage Reference Input Pin No internal bonding. 43 NC Connect to GND. 44 AVDD Analog Power Supply Pin, 3.0 3.6V 45 AVSS Ground Pin 46 MCLK I Master Clock Input Pin 47 DVSS Ground Pin 48 DVDD Digital Power Supply Pin, 3.0 3.6V Note. All input pins except internal pull-up/down pins must not be left floating. MS1648-E-03 2014/11 -7- [AK4490] Handling of Unused Pin The unused I/O pins should be processed appropriately as below. (1) Parallel Mode (PCM Mode only) Classification Pin Name AOUTLP, AOUTLN Analog AOUTRP, AOUTRN Setting These pins must be open. These pins must be open. Digital This pin must be connected to DVSS or open. I2C (2) Serial Mode 1. PCM Mode Classification Pin Name AOUTLP, AOUTLN Analog AOUTRP, AOUTRN PSN, DEM1 Digital DEM0 Setting These pins must be open. These pins must be open. These pins must be connected to DVSS This pin must be connected to DVDD. 2. DSD Mode Classification Analog Digital Pin Name AOUTLP, AOUTLN AOUTRP, AOUTRN PSN, DEM1 DEM0 pull-up pin List pull-up pin 13, 15 pull-down pin List pull-down pin 14, 16, 17 Setting These pins must be open. These pins must be open. These pins must be connected to DVSS This pin must be connected to DVDD. MS1648-E-03 2014/11 -8- [AK4490] 6. Absolute Maximum Ratings (AVSS=DVSS=VSSL=VSSR=VREFLL=VREFLR=0V; Note 1) Parameter Symbol min max Unit 0.3 4.6 Analog AVDD V Power Supplies: 0.3 7.5 Analog VDDL/R V Digital DVDD V 0.3 4.6 |AVSS DVSS| (Note 2) GND V 0.3 Input Current, Any Pin Except Supplies IIN 10 mA Digital Input Voltage VIND 0.3 DVDD+0.3 V Ambient Temperature (Power applied) Ta 40 85 C Storage Temperature Tstg 65 150 C Note 1. All voltages with respect to ground. Note 2. AVSS, DVSS, VSSL and VSSR must be connected to the same analog ground plane. Note 3. Connect at least 0.1uF or more decoupling capacitors between VDDL/VDDR and VSSL/VSSR to suppress affections by a static electricity noise or an over voltage (includes over shooting) that exceeds absolute maximum ratings. WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. 7. Recommended Operating Conditions (AVSS=DVSS=VSSL=VSSR =0V; Note 1) Parameter Symbol min typ max Analog AVDD 3.0 3.3 3.6 Power Supplies Analog VDDL/R 4.75 5.0 7.2 (Note 4) Digital DVDD 3.0 3.3 3.6 Voltage Reference "H" voltage reference VREFHL/R VDDL/R0.5 VDDL/R (Note 5) "L" voltage reference VREFLL/R VSSL/R Note 1. All voltages with respect to ground. Note 4. The power up sequence between AVDD, VDDL/R and DVDD is not critical. Note 5. The analog output voltage scales with the voltage of (VREFH VREFL). AOUT (typ.@0dB) = (AOUT+) (AOUT) = 2.8Vpp (VREFHL/R VREFLL/R)/5. Unit V V V V V * AKM assumes no responsibility for the usage beyond the conditions in this data sheet. MS1648-E-03 2014/11 -9- [AK4490] 8. Electrical Characteristics Analog Characteristics (Ta=25C; AVDD=DVDD=3.3V; AVSS=DVSS=VSSL/R=0V; VREFHL/R=VDDL/R=5V, VREFLL/R= VSSL/R=0V; Input data = 24bit; RL 1k; BICK=64fs; Signal Frequency = 1kHz; Sampling Frequency = 44.1kHz; Measurement bandwidth = 20Hz ~ 20kHz; External Circuit: Figure 41; unless otherwise specified.) Parameter min typ max Unit Resolution 32 Bits Dynamic Characteristics (Note 6) 0dBFS fs=44.1kHz -112 -105 dB THD+N -57 -49 dB BW=20kHz 60dBFS 0dBFS fs=96kHz -109 -100 dB -54 -44 dB BW=40kHz 60dBFS 0dBFS fs=192kHz -106 -100 dB BW=40kHz 60dBFS -54 -44 dB -51 -41 dB BW=80kHz 60dBFS Dynamic Range (60dBFS with A-weighted) (Note 7) 115 120 dB S/N (A-weighted) (Note 8) 115 120 dB S/N (Mono mode, A-weighted) 118 123 dB Interchannel Isolation (1kHz) 110 120 dB DC Accuracy Interchannel Gain Mismatch 0.15 0.3 dB Gain Drift (Note 9) 20 ppm/C Output Voltage (Note 10) 2.65 2.8 2.95 Vpp Load Capacitance 25 pF Load Resistance (Note 11) 1 k Power Supplies Power Supply Current Normal operation (PDN pin = "H") VDDL/R 22 32 mA AVDD 0.6 1.2 mA DVDD (fs= 44.1kHz) 10 14 mA DVDD (fs= 96kHz) 15 20 mA DVDD (fs = 192kHz) 17 23 mA Power down (PDN pin = "L") (Note 12) AVDD+VDDL/R+DVDD 10 100 A Note 6. Measured by Audio Precision, System Two. Averaging mode. Refer to the evaluation board manual. Note 7. Figure 41 External LPF Circuit Example 2. 101dB for 16-bit data and 118dB for 20-bit data. Note 8. Figure 41 External LPF Circuit Example 2. S/N does not depend on input data size. Note 9. The voltage on (VREFH VREFL) is held +5V externally. Note 10. Full-scale voltage(0dB). Output voltage scales with the voltage of (VREFHL/R VREFLL/R). AOUT (typ.@0dB) = (AOUT+) (AOUT) = 2.8Vpp (VREFHL/R VREFLL/R)/5. Note 11. Regarding Load Resistance, AC load is 1k (min) with a DC cut capacitor (Figure 41). DC load is 1.5k ohm (min) without a DC cut capacitor (Figure 40). The load resistance value is with respect to ground. Analog characteristics are sensitive to capacitive load that is connected to the output pin. Therefore the capacitive load must be minimized. Note 12. In the power down mode. The PSN pin = DVDD, and all other digital input pins including clock pins (MCLK, BICK and LRCK) are held DVSS. MS1648-E-03 2014/11 - 10 - [AK4490] Sharp Roll-Off Filter Characteristics (fs=44.1kHz) (Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Normal Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Digital Filter Passband (Note 13) 0.01dB PB 0 20.0 6.0dB 22.05 Stopband (Note 13) SB 24.1 Passband Ripple PR 0.005 Stopband Attenuation SA 100 Group Delay (Note 14) GD 29.4 Digital Filter + SCF Frequency Response: 0 20.0kHz +0.1/-0.2 - Unit kHz kHz kHz dB dB 1/fs dB Sharp Roll-Off Filter Characteristics (fs=96kHz) Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Double Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 43.5 kHz 6.0dB 48.0 kHz Stopband (Note 13) SB 52.5 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 100 dB Group Delay (Note 14) GD 28.8 1/fs Digital Filter + SCF Frequency Response: 0 40.0kHz +0.1/-0.6 dB Sharp Roll-Off Filter Characteristics (fs=192kHz) (Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Quad Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 87.0 kHz 6.0dB 96.0 kHz Stopband (Note 13) SB 105 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 92 dB Group Delay (Note 14) GD 28.8 1/fs Digital Filter + SCF Frequency Response: 0 80.0kHz +0.1/-0.2 dB Note 13. The passband and stopband frequencies scale with fs. For example, PB=0.4535xfs (@0.01dB), SB=0.546xfs. Note 14. The calculating delay time which occurred by digital filtering. This time is from setting the 16/20/24/32 bit data of both channels to the output of analog signal. MS1648-E-03 2014/11 - 11 - [AK4490] Figure 1. Sharp Roll-off Filter Frequency Response Figure 2. Sharp Roll-off Filter Passband Ripple MS1648-E-03 2014/11 - 12 - [AK4490] Short Delay Sharp Roll-Off Filter Characteristics (fs=44.1kHz) (Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Normal Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Digital Filter Passband (Note 13) 0.01dB PB 0 20.0 6.0dB 22.05 Stopband (Note 13) SB 24.1 Passband Ripple PR 0.005 Stopband Attenuation SA 100 Group Delay (Note 14) GD 6.25 Digital Filter + SCF Frequency Response : 0 20.0kHz -0.1/-0.2 - Unit kHz kHz kHz dB dB 1/fs dB Short Delay Sharp Roll-Off Filter Characteristics (fs=96kHz) (Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Double Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Digital Filter Passband (Note 13) 0.01dB PB 0 43.5 6.0dB 48.0 Stopband (Note 13) SB 52.5 Passband Ripple PR 0.005 Stopband Attenuation SA 100 Group Delay (Note 14) GD 5.63 Digital Filter + SCF Frequency Response : 0 40.0kHz +0.1/-0.6 - Unit kHz kHz kHz dB dB 1/fs dB Short Delay Sharp Roll-Off Filter Characteristics (fs=192kHz) (Ta=25C; AVDD=DVDD=3.0~3.6V, VREFHL/R=VDDL/R=4.75 7.2V; Quad Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H", SLOW bit="0" or SLOW pin = "L") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 87.0 kHz 6.0dB 96.0 kHz Stopband (Note 13) SB 105 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 92 dB Group Delay (Note 14) GD 5.63 1/fs Digital Filter + SCF Frequency Response : 0 80.0kHz +0.1/-2.0 dB MS1648-E-03 2014/11 - 13 - [AK4490] Figure 3. Short delay Sharp Roll-off Filter Frequency Response Figure 4. Short delay Sharp Roll-off Filter Passband Ripple MS1648-E-03 2014/11 - 14 - [AK4490] Slow Roll-Off Filter Characteristics (fs=44.1kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Normal Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="1" or SLOW pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 4.4 kHz 6.0dB 18.2 kHz Stopband (Note 13) SB 39.1 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 94 dB Group Delay (Note 14) GD 6.63 1/fs Digital Filter + SCF Frequency Response: 0 20.0kHz +0.1/-4.5 dB Slow Roll-Off Filter Characteristics (fs=96kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Double Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="1" or SLOW pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 18.1 kHz 6.0dB 45.6 kHz Stopband (Note 13) SB 85.0 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 100 dB Group Delay (Note 14) GD 6.00 1/fs Digital Filter + SCF Frequency Response: 0 40.0kHz +0.1/-4.0 dB Slow Roll-Off Filter Characteristics (fs=192kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Quad Speed Mode; DEM=OFF; SD bit="0" or SD pin = "L", SLOW bit="1" or SLOW pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 32.9 kHz 6.0dB 90.4 kHz Stopband (Note 13) SB 171 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 97 dB Group Delay (Note 14) GD 6.00 1/fs Digital Filter + SCF Frequency Response: 0 80.0kHz +0.1/-5.5 dB Note 15. The passband and stopband frequencies scale with fs. For example, PB=0.4535xfs (@0.01dB), SB=0.546xfs. Note 16. The calculating delay time which occurred by digital filtering. This time is from setting the 16/20/24/32 bit data of both channels to the output of analog signal. MS1648-E-03 2014/11 - 15 - [AK4490] Figure 5. Slow Roll-off Filter Frequency Response Figure 6. Slow Roll-off Filter Passband Ripple MS1648-E-03 2014/11 - 16 - [AK4490] Short Delay Slow Roll-Off Filter Characteristics (fs=44.1kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Normal Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H", SLOW bit="1" or SLOW pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 4.4 kHz 6.0dB 18.2 kHz Stopband (Note 13) SB 39.1 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 94 dB Group Delay (Note 14) GD 5.3 1/fs Digital Filter + SCF Frequency Response : 0 20.0kHz +0.1/-4.5 dB Short Delay Slow Roll-Off Filter Characteristics (fs=96kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Double Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 18.1 kHz 6.0dB 45.6 kHz Stopband (Note 13) SB 85.0 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 100 dB Group Delay (Note 14) GD 4.68 1/fs Digital Filter + SCF Frequency Response : 0 40.0kHz +0.1/-0.4 dB Short Delay Slow Roll-Off Filter Characteristics (fs=192kHz) (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V; Quad Speed Mode; DEM=OFF; SD bit="1" or SD pin = "H") Parameter Symbol min typ max Unit Digital Filter Passband (Note 13) 0.01dB PB 0 32.9 kHz 6.0dB 96.0 kHz Stopband (Note 13) SB 170 kHz Passband Ripple PR 0.005 dB Stopband Attenuation SA 97 dB Group Delay (Note 14) GD 4.68 1/fs Digital Filter + SCF Frequency Response : 0 80.0kHz +0.1/-5.5 dB MS1648-E-03 2014/11 - 17 - [AK4490] Figure 7. Short Delay Slow Roll-off Filter Frequency Response Figure 8. Short Delay Slow Roll-off Filter Passband Ripple MS1648-E-03 2014/11 - 18 - [AK4490] DSD Mode Characteristics (Ta=-40~85C; VDDL/R=4.75 7.2V, AVDD= DVDD=3.0 3.6V; fs=44.1kHz; D/P bit="1", DSDF bit="0") Parameter min typ max Unit Digital Filter Response 20kHz -0.4 dB Frequency Response (Note 18) 50kHz -2.8 dB 100kHz -15.5 dB (Ta=-40~85C; VDDL/R=4.75 7.2V, AVDD= DVDD=3.0 3.6V; fs=44.1kHz; D/P bit="1", DSDF bit="1" DSDD bit="1") Parameter min typ max Unit Digital Filter Response 20kHz -0.05 dB Frequency Response (Note 18) 50kHz -0.29 dB 100kHz -1.16 dB 150kHz -2.8 dB Note 17. The peak level of DSD signal should be in the range of 25% ~ 75% Duty according to the SACD format book (Scarlet Book). Note 18. The output level is assumed as 0dB when a 1kHz 25% ~ 75% Duty sine wave is input. DC Characteristics (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V) Parameter Symbol min typ max Unit High-Level Input Voltage VIH 70%DVDD V Low-Level Input Voltage VIL 30%DVDD V High-Level Output Voltage (Iout=100A) VOH DVDD0.5 V Low-Level Output Voltage (DZFL, DZFR pins: Iout=100A) VOL 0.5 V (SDA pin: Iout=3mA) VOL 0.4 V Input Leakage Current (Note 19) Iin 10 A Note 19. The DEM1, I2C and ACKS pins have internal pull-down and DEM0 and PSN pins have internal pull-up devices, nominally 100k. Therefore the DEM1, I2C, ACKS, DEM0 and PSN pins are not included. MS1648-E-03 2014/11 - 19 - [AK4490] Switching Characteristics (Ta=25C; AVDD=DVDD=3.0 3.6, VREFHL/R=VDDL/R=4.75 7.2V)) Parameter Symbol min Master Clock Timing Frequency fCLK 7.7 Duty Cycle dCLK 40 Minimum Pulse Width tCLKH 9.155 tCLKL 9.155 LRCK Frequency (Note 20) 1152fs, 512fs or 768fs 30 fsn 256fs or 384fs 54 fsd 128fs or 192fs fsq 108 fsoc 64fs fssd 64fs Duty Duty Cycle 45 PCM Audio Interface Timing BICK Period 1152fs, 512fs or 768fs tBCK 1/128fsn 256fs or 384fs tBCK 1/64fsd 128fs or 192fs tBCK 1/64fsq 64fs tBCK 1/64fso 64fs tBCK 1/64fsh BICK Pulse Width Low tBCKL 9 BICK Pulse Width High tBCKH 9 BICK "" to LRCK Edge (Note 21) tBLR 5 LRCK Edge to BICK "" (Note 21) tLRB 5 SDATA Hold Time tSDH 5 SDATA Setup Time tSDS 5 External Digital Filter Mode BICK Period tB 27 BCK Pulse Width Low tBL 10 BCK Pulse Width High tBH 10 BCK "" to WCK Edge tBW 5 WCK Period tWCK 1.3 WCK Edge to BCK "" tWB 5 WCK Pulse Width Low tWCK 54 WCK Pulse Width High tWCH 54 DATA Hold Time tDH 5 DATA Setup Time tDS 5 DSD Audio Interface Timing (64 mode, DSDSEL 1-0 bits = "00") DCLK Period tDCK DCLK Pulse Width Low tDCKL 160 DCLK Pulse Width High tDCKH 160 DCLK Edge to DSDL/R (Note 22) tDDD 20 MS1648-E-03 typ max Unit 49.152 60 MHz % ns ns 54 108 216 kHz kHz kHz kHz kHz % 384 768 55 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns s ns ns ns ns ns 1/64fs 20 ns ns ns ns 2014/11 - 20 - [AK4490] DSD Audio Interface Timing (128 mode, DSDSEL 1-0 bits = "01") DCLK Period tDCK 1/128fs ns DCLK Pulse Width Low tDCKL 80 ns DCLK Pulse Width High tDCKH 80 ns DCLK Edge to DSDL/R (Note 22) tDDD 10 10 ns DSD Audio Interface Timing (256 mode, DSDSEL 1-0 bit = "10") DCLK Period tDCK 1/256fs ns DCLK Pulse Width Low tDCKL 40 ns DCLK Pulse Width High tDCKH 40 ns DCLK Edge to DSDL/R (Note 22) tDDD 5 5 ns Control Interface Timing CCLK Period tCCK 200 ns CCLK Pulse Width Low tCCKL 80 ns Pulse Width High tCCKH 80 ns CDTI Setup Time tCDS 50 ns CDTI Hold Time tCDH 50 ns CSN High Time tCSW 150 ns CSN "" to CCLK "" tCSS 50 ns CCLK "" to CSN "" tCSH 50 ns 2 Control Interface Timing (I C Bus mode): SCL Clock Frequency fSCL 400 kHz Bus Free Time Between Transmissions tBUF 1.3 s Start Condition Hold Time (prior to first clock pulse) tHD:STA 0.6 s Clock Low Time tLOW 1.3 s Clock High Time tHIGH 0.6 s Setup Time for Repeated Start Condition tSU:STA 0.6 s SDA Hold Time from SCL Falling (Note 23) tHD:DAT 0 s SDA Setup Time from SCL Rising tSU:DAT 0.1 s Rise Time of Both SDA and SCL Lines tR 0.3 s Fall Time of Both SDA and SCL Lines tF 0.3 s Setup Time for Stop Condition tSU:STO 0.6 s Pulse Width of Spike Noise Suppressed by Input Filter tSP 0 50 ns Capacitive load on bus Cb 400 pF Reset Timing PDN Pulse Width (Note 24) tPD 150 ns Note 20. When the 1152fs, 512fs or 768fs /256fs or 384fs /128fs or 192fs are switched, the AK4490 should be reset by the PDN pin or RSTN bit. Note 21. BICK rising edge must not occur at the same time as LRCK edge. Note 22. DSD data transmitting device must meet this time. Note 23. Data must be held for sufficient time to bridge the 300 ns transition time of SCL. Note 24. The AK4490 can be reset by bringing the PDN pin to "L". MS1648-E-03 2014/11 - 21 - [AK4490] Timing Diagram 1/fCLK VIH MCLK VIL tCLKH tCLKL dCLK=tCLKH x fCLK, tCLKL x fCLK 1/fs VIH LRCK VIL tBCK VIH BICK VIL tBCKH tBCKL tWCK VIH WCK VIL tWCKH tWCKL tB VIH BCK VIL tBH tBL Clock Timing MS1648-E-03 2014/11 - 22 - [AK4490] VIH LRCK VIL tBLR tLRB VIH BICK VIL tSDS tSDH VIH SDATA VIL Audio Interface Timing (PCM Mode) tDCK tDCKL tDCKH VIH DCLK VIL tDDD VIH DSDL DSDR VIL tDDD VIH DSDL DSDR VIL Audio Serial Interface Timing (DSD Normal Mode, DCKB bit = "0") MS1648-E-03 2014/11 - 23 - [AK4490] tDCK tDCKL tDCKH VIH DCLK VIL tDDD tDDD VIH DSDL DSDR VIL tDDD tDDD VIH DSDL DSDR VIL Audio Serial Interface Timing (DSD Phase Modulation Mode, DCKB bit = "0") VIH CSN VIL tCSS tCCKL tCCKH VIH CCLK VIL tCDS CDTI C1 tCDH C0 R/W A4 VIH VIL WRITE Command Input Timing MS1648-E-03 2014/11 - 24 - [AK4490] tCSW VIH CSN VIL tCSH VIH CCLK VIL CDTI D3 D2 D1 VIH D0 VIL WRITE Data Input Timing VIH SDA VIL tBUF tLOW tR tHIGH tF tSP VIH SCL VIL tHD:STA Stop tHD:DAT tSU:DAT Start tSU:STA tSU:STO Start Stop I2C Bus Mode Timing MS1648-E-03 2014/11 - 25 - [AK4490] tPD PDN VIL Power Down & Reset Timing VIH WCK VIL tBW tWB VIH BCK VIL tDS tDH VIH DINL DINR VIL External Digital Filter I/F mode MS1648-E-03 2014/11 - 26 - [AK4490] 9. Functional Descriptions D/A Conversion Mode In serial mode, the AK4490 can perform D/A conversion for either PCM data or DSD data. The D/P bit controls PCM/DSD mode. When DSD mode, DSD data can be input from DCLK, DSDL and DSDR pins. When PCM mode, PCM data can be input from BICK, LRCK and SDATA pins. When PCM/DSD mode is changed by D/P bit, the AK4490 should be reset by RSTN bit. It takes about 2/fs to 3/fs to change the mode. In parallel mode, the AK4490 performs for only PCM data. DP bit Interface 0 PCM 1 DSD Table 1. PCM/DSD Mode Control When DP bit= "0", an internal digital filter or external digital filter can be selected. When using an external digital filter (EX DF I/F mode), data is input to each MCLK, BCK, WCK, DINL and DINR pin. EXDF bit controls the modes. When switching internal and external digital filters, the AK4490 must be reset by RSTN bit. A Digital filter switching takes 2~3k/fs. EXDF bit Interface 0 PCM 1 EX DF I/F Table 2. Digital Filter Control (DP bit = "0") System Clock [1] PCM Mode The external clocks, which are required to operate the AK4490, are MCLK, BICK and LRCK. MCLK should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. There are two modes for MCLK frequency setting: Manual Setting Mode and Auto Setting Mode. In manual setting mode, MCLK frequency is set automatically (Table 4). In auto setting mode, sampling speed and MCLK frequency are detected automatically (Table 5) and then the initial master clock is set to the appropriate frequency (Table 6). When the reset is released (PDN pin = ""), the AK4490 is in auto setting mode. The AK4490 is automatically placed in reset state when MCLK and LRCK are stopped during a normal operation (PDN pin ="H"), and the analog output becomes Hi-z state. When MCLK and LRCK are input again, the AK4490 exits reset state and starts operation. After exiting system reset (PDN pin ="L""H") at power-up and other situations, the AK4490 is in power-down mode until MCLK and LRCK are supplied. The MCLK frequency corresponding to each sampling speed should be provided externally (Table 3). MS1648-E-03 2014/11 - 27 - [AK4490] (1) Parallel Mode (PSN pin = "H") 1. Manual Setting Mode (ACKS pin = "L") The MCLK frequency corresponding to each sampling speed should be provided externally (Table 3). DFS1-0 bit is fixed to "00". In this mode, quad speed and double speed modes are not available. LRCK MCLK (MHz) BICK fs 128fs 192fs 256fs 384fs 512fs 768fs 1152fs 64fs 32.0kHz N/A N/A 8.1920 12.2880 16.3840 24.5760 36.8640 2.0480MHz 44.1kHz N/A N/A 11.2896 16.9344 22.5792 33.8688 N/A 2.8224MHz 48.0kHz N/A N/A 12.2880 18.4320 24.5760 36.8640 N/A 3.0720MHz Table 3. System Clock Example (Manual Setting Mode @Parallel Mode) (N/A: Not available) In manual setting mode, the AK4490 supports sampling rate from 32kHz to 96kHz (Table 4). However, the DR and S/N performances of when MCLK=256fs/384fs will degrade approximately 3dB as compared to when MCLK=512fs/768fs if the sampling rate is 32kHz~48kHz. ACKS pin MCLK DR,S/N L 256fs/384fs/512fs/768fs 120dB H 256fs/384fs 117dB H 512fs/768fs 120dB Table 4. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz) 2. Auto Setting Mode (ACKS pin = "H") In auto setting mode, MCLK frequency and sampling frequency are detected automatically (Table 5). MCLK of corresponded frequency to each sampling speed mode should be input externally. (Table 6) MCLK Sampling Speed 1152fs Normal (fs32kHz) 512/256fs 768/384fs Normal 256fs 384fs Double 128fs 192fs Quad 64fs 96fs Oct 32fs 48fs Hex Table 5. Sampling Speed (Auto Setting Mode @Parallel Mode) LRCK MCLK (MHz) Sampling Speed fs 32fs 48fs 64fs 96fs 128fs 192fs 256fs 384fs 512fs 768fs 1152fs N/A N/A N/A N/A N/A N/A 8.192 12.288 16.384 24.576 36.864 32.0kHz N/A N/A N/A N/A N/A N/A 11.2896 16.9344 22.5792 33.8688 N/A 44.1kHz Normal N/A N/A N/A N/A N/A N/A 12.288 18.432 24.576 36.864 N/A 48.0kHz N/A N/A N/A N/A N/A N/A 22.5792 33.8688 N/A N/A N/A 88.2kHz Double N/A N/A N/A N/A N/A N/A 24.576 36.864 N/A N/A N/A 96.0kHz N/A N/A N/A 22.5792 33.8688 N/A N/A N/A N/A N/A 176.4kHz N/A Quad N/A N/A N/A 24.576 36.864 N/A N/A N/A N/A N/A 192.0kHz N/A Quad N/A N/A 24.576 36.864 N/A N/A N/A N/A N/A N/A N/A 384kHz Oct 24.576 36.864 N/A N/A N/A N/A N/A N/A N/A N/A N/A 768kHz Hex Table 6. System Clock Example (Auto Setting Mode @Parallel Mode) (N/A: Not available) MS1648-E-03 2014/11 - 28 - [AK4490] When MCLK= 256fs/384fs, auto setting mode supports sampling rate of 32kHz~96kHz (Table 7). However, the DR and S/N performances will degrade approximately 3dB as compared to when MCLK= 512fs/768fs when the sampling rate is 32kHz~48kHz. ACKS pin MCLK DR,S/N L 256fs/384fs/512fs/768fs 120dB H 256fs/384fs 117dB H 512fs/768fs 120dB Table 7. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz) 3. Digital filter The AK4490 has four kinds of digital filter selected by SD and SLOW pins. Different sound qualities on playback can be selected by these filters. SD pin L L H H SLOW pin L H L H Mode Sharp roll-off filter Slow roll-off filter Short delay Sharp roll-off filter Short delay Slow roll-off filter Table 8. Digital Filter Setting (default) The AK4490 can be operated on a slower sampling frequency. This mode is available when the SSLOW pin = "H". (2) Serial Mode (PSN pin = "L") 1. Manual Setting Mode (ACKS bit = "0") MCLK frequency is detected automatically and the sampling speed is set by DFS2-0 bits (Table 9). The MCLK frequency corresponding to each sampling speed should be provided externally (Table 10). The AK4490 is set to Manual Setting Mode at power-up (PDN pin = "L" "H"). When DFS2-0 bits are changed, the AK4490 should be reset by RSTN bit. DFS2 0 0 0 0 1 1 1 1 DFS1 0 0 DFS0 0 1 Sampling Rate (fs) Normal Speed Mode 30kHz 54kHz (default) Double Speed Mode 54kHz 108kHz 120kHz 1 0 Quad Speed Mode 216kHz 1 1 Reserved 0 0 Oct Speed Mode 384kHz 0 1 Hex Speed Mode 768kHz 1 0 Reserved 1 1 Reserved Table 9. Sampling Speed (Manual Setting Mode @Serial Mode) MS1648-E-03 2014/11 - 29 - [AK4490] LRCK fs 32.0kHz 44.1kHz 48.0kHz 88.2kHz 96.0kHz 176.4kHz 192.0kHz 384kHz 768kHz 32fs 48fs 64fs 96fs 128fs N/A N/A N/A N/A N/A N/A N/A 12.288 24.576 N/A N/A N/A N/A N/A N/A N/A 18.432 36.864 N/A N/A N/A N/A N/A N/A N/A 24.576 49.152 N/A N/A N/A N/A N/A N/A N/A 36.864 N/A N/A N/A N/A N/A N/A 22.5792 24.5760 49.152 N/A MCLK (MHz) 192fs 256fs N/A N/A N/A N/A N/A 33.8688 36.8640 N/A N/A 8.1920 11.2896 12.2880 22.5792 24.5760 45.1584 49.152 N/A N/A 384fs 512fs 768fs 1152fs 12.2880 16.9344 18.4320 33.8688 36.8640 N/A N/A N/A N/A 16.3840 22.5792 24.5760 N/A N/A N/A N/A N/A N/A 24.5760 33.8688 36.8640 N/A N/A N/A N/A N/A N/A 36.8640 N/A N/A N/A N/A N/A N/A N/A N/A Sampling Speed Normal Double Quad Quad Oct Hex Table 10. System Clock Example (Manual Setting Mode @Serial Mode) 2. Auto Setting Mode (ACKS bit = "1") MCLK frequency and the sampling speed are detected automatically (Table 11) and DFS1-0 bits are ignored. The MCLK frequency corresponding to each sampling speed should be provided externally (Table 12). MCLK Sampling Speed 1152fs Normal (fs32kHz) 512/256fs 768/384fs Normal 256fs 384fs Double 128fs 192fs Quad Table 11. Sampling Speed (Auto Setting Mode @Serial Mode) LRCK MCLK(MHz) Sampling Speed fs 32fs 48fs 64fs 96fs 128fs 192fs 256fs 384fs 512fs 768fs 1152fs N/A N/A N/A N/A N/A N/A 8.192 12.288 16.384 24.576 36.864 32.0kHz N/A N/A N/A N/A N/A N/A 11.2896 16.9344 22.5792 33.8688 N/A 44.1kHz Normal N/A N/A N/A N/A N/A N/A 12.288 18.432 24.576 36.864 N/A 48.0kHz N/A N/A N/A N/A N/A N/A 22.5792 33.8688 N/A N/A N/A 88.2kHz Double N/A N/A N/A N/A N/A N/A 24.576 36.864 N/A N/A N/A 96.0kHz N/A N/A N/A 22.5792 33.8688 N/A N/A N/A N/A N/A 176.4kHz N/A Quad N/A N/A N/A 24.576 36.864 N/A N/A N/A N/A N/A 192.0kHz N/A Quad N/A N/A 24.576 36.864 N/A N/A N/A N/A N/A N/A N/A 384kHz Oct N/A N/A N/A N/A N/A N/A N/A N/A 768kHz 24.576 36.864 N/A Hex Table 12. System Clock Example (Auto Setting Mode @Serial Mode) When MCLK= 256fs/384fs, auto setting mode supports sampling rate of 32kHz~96kHz (Table 13). However, the DR and S/N performances will degrade approximately 3dB as compared to when MCLK= 512fs/768fs when the sampling rate is 32kHz~48kHz. ACKS bit MCLK DR,S/N 0 256fs/384fs/512fs/768fs 120dB 1 256fs/384fs 117dB 1 512fs/768fs 120dB Table 13. Relationship of MCLK Frequency and DR, S/N Performance (fs = 44.1kHz) MS1648-E-03 2014/11 - 30 - [AK4490] 3. Digital filter The AK4490 has four kinds of digital filter selected by SD and SLOW bits. Different sound qualities on playback can be selected by these filters. SD bit 0 0 1 1 SLOW bit 0 1 0 1 Mode Sharp roll-off filter Slow roll-off filter Short delay Sharp roll-off filter Short delay Slow roll-off filter Table 14. Digital Filter Setting (default) The AK4490 can be operated on a slower sampling frequency. This mode is available when the SSLOW bit = "H" (05H D0). MS1648-E-03 2014/11 - 31 - [AK4490] [2] DSD Mode The AK4490 has a DSD playback function. The external clocks, which are required in DSD mode, are MCLK and DCLK. MCLK should be synchronized with DCLK but the phase is not critical. The frequency of MCLK is set by DCKS bit. The AK4490 is automatically placed in reset state when MCLK is stopped during a normal operation (PDN pin ="H"), and the analog output becomes Hi-z state. However, the external clock (DCLK) should not be stopped. When DCLK is not supplied, the AK4490 may not be able to operate properly because of an over current since it has a dynamic logic circuit internally. The PDN pin should be set to "L" when stopping the DCLK. When the reset is released (PDN pin = "L" "H"), the AK4490 is in power-down state until MCLK and DCLK are input. DCKS bit 0 1 MCLK Frequency DCLK Frequency 512fs 64fs/128fs/256fs 768fs 64fs/128fs/256fs Table 15. System Clock (DSD Mode) (default) The AK4490 supports DSD data stream of 2.8224MHz (64fs), 5.6448MHz (128fs) and 11.2896MHz (256fs). The data sampling speed is selected by DSDSEL1-0 bits. DSDSEL1 DSDSEL0 DSD data stream 0 0 2.8224MHz (default) 0 1 5.6448MHz 1 0 11.2896MHz 1 1 Reserved Table 16. DSD Sampling Speed Control The AK4490 has a Volume bypass function for play backing DSD signal. Two modes are selectable by DSDD bit. When setting DSDD bit = "1", the output volume control function is not available. DSDD Mode 0 Normal Path (default) 1 Volume Bypass Table 17. DSD Play Back Mode Control When DSDD bit = "1", filter characteristic can be switched between 50kHz and 100kHz by DSDF bit. DSDD bit 0 0 DSDF bit 0 1 1 1 0 1 Cut Off Filter 50kHz Reserved (default) 50kHz 150kHz Table 18. DSD Filter Select MS1648-E-03 2014/11 - 32 - [AK4490] Full Scale (FS) DSD Signal Detection Function The AK4490 has a full scale (FS) detection function at each channel in DSD Mode. When DSDL or DSDR input data is continuously "0" (-FS) or "1" (+FS) for 2048 cycles, the AK4490 detects full scale and enters full scale detection status and DML or DMR bit becomes "1". The output will be muted by full scale detection if DDM bit = "1". When DSDD bit is "0", the output is attenuated in soft transition. When DSDD bit is "1", the soft transition is disabled. Recovery method to normal operation mode from full scale detection status is controlled by DMC bit when DDM bit = "1". When DMC bit = "0", the AK4490 returns to normal operation automatically by a normal signal input. When DMC bit = "1", the AK4490 returns normal operation by writing DMRE bit = "1". DSDD 0 1 Mode Status After Detection Normal Path DSD Mute (default) Volume Bypass PD Table 19. DSD Mode and the Device Status after Detection (DDM bit= "0") DSD Error (DDR or DDLbit) DSD Data 2048fs DSD Data DSD Data(FS or -FS ) DSD Data AOUT Mode Figure 9. Analog Output Waveform on DSD FS Detection (DSDD bit= "1") 2048fs DSD Error (DDR or DDLbit) DSD Data DSD Data DSD Data(FS or -FS ) DSD Data AOUT Mode Figure 10. Analog Output Waveform on DSD FS Detection (DSDD bit= "0") MS1648-E-03 2014/11 - 33 - [AK4490] Audio Interface Format [1] PCM Mode Data is shifted in via the SDATA pin using BICK and LRCK inputs. Eight data formats are supported and selected by the DIF2-0 pins (Parallel control mode) or DIF2-0 bits (Serial control mode) as shown in Table 20. In all formats the serial data is MSB-first, 2's compliment format and is latched on the rising edge of BICK. Mode 2 can be used for 20-bit and 16-bit MSB justified formats by zeroing the unused LSBs. Mode 0 1 2 3 4 5 6 7 DIF2 0 0 0 0 1 1 1 1 DIF1 0 0 1 1 0 0 1 1 DIF0 Input Format BICK 0 16-bit LSB justified 32fs 1 20-bit LSB justified 48fs 0 24-bit MSB justified 48fs 2 1 24-bit I S compatible 48fs 0 24-bit LSB justified 48fs 1 32-bit LSB justified 64fs 0 32-bit MSB justified 64fs 1 32-bit I2S compatible 64fs Table 20. Audio Interface Format Figure Figure 11 Figure 12 Figure 13 Figure 14 Figure 12 Figure 15 Figure 16 Figure 17 (default) LRCK 0 1 10 11 12 13 14 15 0 1 10 11 12 13 14 15 0 1 BICK (32fs) SDATA Mode 0 15 0 14 1 6 5 14 4 15 3 16 2 17 1 0 31 15 0 14 1 6 5 14 4 15 3 16 2 17 1 0 31 15 0 14 1 BICK (64fs) SDATA Mode 0 Don't care 15 14 0 Don't care 15 14 0 15:MSB, 0:LSB Lch Data Rch Data Figure 11. Mode 0 Timing MS1648-E-03 2014/11 - 34 - [AK4490] LRCK 0 1 8 9 10 11 12 31 0 1 8 9 10 11 12 31 0 1 BICK (64fs) SDATA Mode 1 Don't care 19 0 Don't care 19 0 Don't care 19 0 19 0 19:MSB, 0:LSB SDATA Mode 4 23 Don't care 22 21 20 23 22 20 21 23:MSB, 0:LSB Lch Data Rch Data Figure 12. Mode 1/4 Timing LRCK 0 1 2 22 23 24 30 31 0 1 2 22 23 24 30 31 0 1 BICK (64fs) SDATA 23 22 1 0 Don't care 23 22 0 1 Don't care 23 22 0 1 23:MSB, 0:LSB Lch Data Rch Data Figure 13. Mode 2 Timing LRCK 0 1 2 3 23 24 25 31 0 1 2 3 23 24 25 31 BICK (64fs) SDATA 23 22 1 0 Don't care 23 22 1 0 Don't care 23 23:MSB, 0:LSB Lch Data Rch Data Figure 14. Mode 3 Timing MS1648-E-03 2014/11 - 35 - [AK4490] LRCK 0 1 2 20 21 22 32 33 63 0 1 2 20 21 22 32 33 63 0 1 BICK(128fs) SDATA 31 0 1 2 12 13 14 23 1 24 0 31 31 0 1 2 12 13 14 23 1 24 0 31 0 1 BICK(64fs) SDATA 31 30 20 19 18 8 9 0 1 31 30 20 19 18 Lch Data 8 9 0 1 31 Rch Data 31: MSB, 0:LSB Figure 15. Mode 5 Timing LRCK 0 1 2 20 21 22 32 33 63 0 1 2 20 21 22 32 33 63 0 1 BICK(128fs) SDATA 31 30 0 1 12 11 10 2 12 13 0 14 31 30 23 24 31 0 1 12 11 10 2 12 0 13 14 31 23 24 31 0 1 BICK(64fs) SDATA 31 30 20 19 18 8 9 0 1 31 30 20 19 18 Lch Data 8 9 0 1 31 Rch Data 31: MSB, 0:LSB Figure 16. Mode 6 Timing LRCK 0 1 2 20 21 22 33 34 63 0 1 2 20 21 22 33 34 63 24 25 31 0 1 BICK(128fs) SDATA 31 0 1 13 12 11 2 12 13 0 14 31 24 25 31 0 1 13 2 12 11 12 0 13 14 0 1 BICK(64fs) SDATA 0 31 21 20 19 9 8 2 1 0 31 Lch Data 21 20 19 9 8 2 1 0 Rch Data 31: MSB, 0:LSB Figure 17. Mode 7 Timing MS1648-E-03 2014/11 - 36 - [AK4490] [2] DSD Mode In case of DSD mode, DIF2-0 pins and DIF2-0 bits are ignored. The frequency of DCLK is selected between 64fs, 128fs and 256fs. DCKB bit can invert the polarity of DCLK. Phase modulation function is not available in 256fs mode. DCLK (64fs) DCKB=1 DCLK (64fs) DCKB=0 DSDL,DSDR Normal D0 DSDL,DSDR Phase Modulation D0 D1 D1 D2 D1 D2 D3 D2 D3 Figure 18. DSD Mode Timing MS1648-E-03 2014/11 - 37 - [AK4490] [3] External Digital Filter Mode (EX DF I/F Mode) DW indicates the number of BCK in one WCK cycle. The audio data is input by MCLK, BCK and WCK from the DINL and DINR pins. Three formats are available (Table 22) by DIF2-0 bits setting. The data is latched on the rising edge of BCK. The BCK and MCLK clocks must be the same frequency and must not burst. BCK and MCLK frequencies for each sampling speed are shown in Table 21. Sampling Speed[kHz] 44.1(30~48) 44.1(30~48) 96(54~96) 96(54~96) 192(108~192) 192(108~192) MCLK&BCK [MHz] 128fs N/A N/A N/A N/A N/A N/A 12.288 32 192fs N/A N/A N/A N/A N/A N/A 256fs N/A N/A 11.2896 32 384fs N/A N/A WCK 512fs 16fs 32 48 DW 16.9344 33.8688 N/A 8fs 48 N/A 96 DW 24.576 36.864 N/A N/A 8fs 32 48 N/A N/A DW 18.432 36.864 N/A N/A N/A 4fs 48 N/A 96 N/A N/A DW 24.576 36.864 N/A N/A N/A N/A 4fs 32 48 N/A N/A N/A N/A DW 36.864 N/A N/A N/A N/A N/A 2fs N/A 96 N/A N/A N/A N/A DW Table 21. System Clock Example (EX DF I/F mode) (N/A: Not available) 22.5792 ECS 768fs 33.8688 0 (default) 1 0 1 0 1 Mode DIF2 DIF1 DIF0 Input Format 0 0 0 0 16-bit LSB justified 1 0 0 1 N/A 2 0 1 0 N/A 3 0 1 1 N/A 4 1 0 0 24-bit LSB justified 5 1 0 1 32-bit LSB justified (default) 6 1 1 0 N/A 7 1 1 1 N/A Table 22. Audio Interface Format (EX DF I/F mode) (N/A: Not available) MS1648-E-03 2014/11 - 38 - [AK4490] 1/16fs or 1/8fs or 1/4fs or 1/2fs WCK 0 1 8 9 10 11 16 17 26 27 28 29 30 31 0 1 BCK DINL or DINR 31 0 30 1 24 23 5 22 6 21 7 20 17 8 16 47 15 48 14 6 5 4 65 49 3 92 2 93 1 94 0 95 0 1 BCK DINL or DINR Don't care 0 1 Don't care 5 6 7 Don't care 8 23 24 31 17 25 2 3 44 45 1 46 0 Don't care 47 0 1 BCK DINL or DINR Don't care Don't care Don't care 31 3 2 1 0 Don't care Figure 19. EX DF I/F Mode Timing D/A Conversion Mode Switching Timing RSTN bit 4/fs D/A Mode PCM Mode DSD Mode 0 D/A Data PCM Data DSD Data Figure 20. D/A Mode Switching Timing (PCM to DSD) RSTN bit D/A Mode DSD Mode PCM Mode 4/fs D/A Data DSD Data PCM Data Figure 21. D/A Mode Switching Timing (DSD to PCM) Note. The signal range is identified as 25% ~ 75% duty ratios in DSD mode. DSD signal must not go beyond this duty range at the SACD format book (Scarlet Book). MS1648-E-03 2014/11 - 39 - [AK4490] De-emphasis Filter A digital de-emphasis filter is available for 32kHz, 44.1kHz or 48kHz sampling rates (tc = 50/15s) and is enabled or disabled with DEM1-0 pins or DEM1-0 bits. In case of 256fs/384fs and 128fs/192fs, the digital de-emphasis filter is always off. When DSD mode, DEM1-0 bits are ignored. The setting value is held even if PCM mode and DSD mode are switched. DEM1 DEM0 Mode 0 0 44.1kHz 0 1 OFF (default) 1 0 48kHz 1 1 32kHz Table 23. De-emphasis Control Output Volume (PCM, DSD) The AK4490 includes channel independent digital output volumes (ATT) with 256 levels at 0.5dB step including MUTE. This volume control is in front of the DAC and it can attenuate the input data from 0dB to -127dB or mute. When changing output levels, it is executed in soft transition thus no switching noise occurs during these transitions. It takes 7424/fs from FFH (0dB) to 00H (MUTE). The attenuation level is initialized to FFH by initial reset. Register setting values will be kept even switching the PCM and DSD modes. Transition Time 0dB to MUTE fs=44.1kHz 168.3ms fs=96kHz 77.3ms fs=192kHz 38.6ms Table 24. ATT Transition Time Sampling Speed MS1648-E-03 2014/11 - 40 - [AK4490] Zero Detection (PCM, DSD) The AK4490 has a channel-independent zeros detect function. When the input data at each channel is continuously zeros for 8192 LRCK cycles, the DZF pin of each channel goes to "H". The DZF pin of each channel immediately returns to "L" if the input data of each channel is not zero after going to "H". If the RSTN bit is "0", the DZF pins of both L and R channels go to "H". The DZF pin of each channel returns to "L" in 4 ~ 5/fs after the input data of each channel becomes "1" when RSTN bit is set to "1". If DZFM bit is set to "1", the DZF pins of both L and R channels go to "H" only when the input data for both channels are continuously zeros for 8192 LRCK cycles. The zero detect function can be disabled by setting the DZFE bit. In this case, DZF pins of both channels are always "L". The DZFB bit can invert the polarity of the DZF pin. DZFE DZFB 0 1 Data DZF-pin L 0 H not zero L 0 Zero detect H 1 not zero H 1 Zero detect L Table 25. Zero Detect Function and DZF Pin Output Mono Output (PCM, DSD, EX DF I/F) The AK4490 can select input/output for both output channels by setting the MONO bit and SELLR bit. This function is available for any audio format. MONO bit 0 0 1 1 SELLR bit Lch Out 0 Lch In 1 Rch In 0 Lch In 1 Rch In Table 26 MONO Mode Output Select Rch Out Rch In Lch In Lch In Rch In Sound Quality Control (PCM, DSD, Ex DF I/F) Sound quality of the AK4490 can be selected by SC1-0 bits. SC1 0 0 1 1 SC0 0 1 0 Mode Sound Setting 1 Sound Setting 2 Sound Setting 3 (default) 1 Reserved Table 27. SC1-0 bits Control MS1648-E-03 2014/11 - 41 - [AK4490] Characteristics (DSD) (Ta=25C; AVDD=DVDD=3.3V; AVSS=DVSS=VSSL/R=0V; VREFHL/R=VDDL/R=5V, VREFLL/R= VSSL/R=0V; Input data = 24bit; RL 1k; Signal Frequency = 1kHz; Sampling Frequency = 44.1kHz; Measurement bandwidth = 20Hz ~ 20kHz; External Circuit: Figure 41; unless otherwise specified.) Dynamic Characteristics DSD data stream 2.8224MHz 0dBFS -110 dB THD+N -110 dB DSD data stream 5.6448MHz 0dBFS DSD data stream 0dBFS -110 dB 11.2896MHz S/N (A-weighted, Normal path) Digital "0" 120 dB DC Accuracy Output Voltage (Normal path ) 2.8 Vpp Output Voltage (Volume pass ) 1.87 Vpp MS1648-E-03 2014/11 - 42 - [AK4490] Soft Mute Operation (PCM, DSD) The soft mute operation is performed at digital domain. When the SMUTE pin goes to "H" or the SMUTE bit set to "1", the output signal is attenuated by during ATT_DATA ATT transition time from the current ATT level. When the SMUTE pin is returned to "L" or the SMUTE bit is returned to "0", the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATA ATT transition time. If the soft mute is cancelled before attenuating after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without stopping the signal transmission. SMUTE pin or SMUTE bit (1) (1) ATT_Level (3) Attenuation - GD (2) GD (2) AOUT DZF pin (4) 8192/fs Notes: (1) ATT_DATA ATT transition time. For example, this time is 7424LRCK cycles (1020/fs) at ATT_DATA=255 in Normal Speed Mode. (2) The analog output corresponding to the digital input has group delay (GD). (3) If the soft mute is cancelled before attenuating after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. (4) When the input data for each channel is continuously zeros for 8192 LRCK cycles, the DZF pin for each channel goes to "H". The DZF pin immediately returns to "L" if input data are not zero. Figure 22. Soft Mute Function System Reset The AK4490 should be reset once by bringing the PDN pin = "L" upon power-up. It initializes register settings of the device. The analog block of the AK4490 exits power-down mode by MCLK input, and the digital block exits power-down mode after the internal counter counts MCLK for 4/fs. MS1648-E-03 2014/11 - 43 - [AK4490] Power ON/OFF timing The AK4490 is placed in the power-down mode by bringing the PDN pin "L" and the registers are initialized. The analog outputs are floating (Hi-Z). As some click noise occurs at the edge of the PDN pin signal, the analog output should be muted externally if the click noise influences system application. The DAC can be reset by setting RSTN bit to "0". In this case, registers are not initialized and the corresponding analog outputs go to VCML/R. As some click noise occurs at the edge of RSTN signal, the analog output should be muted externally if click noise aversely affect system performance. Power PDN pin (1) Internal State Normal Operation DAC In (Digital) "0"data "0"data GD DAC Out (Analog) (3) Reset (2) (4) GD (4) (3) (5) Clock In Don't care Don't care MCLK,LRCK,BICK (7) DZFL/DZFR External Mute (6) Mute ON Mute ON Notes: (1) Digital and analog power supply should be powered up at the same time otherwise power up the 3.3V base power supplies (DVDD, AVDD) first and 5V base power supplies next (VDDL/R, VREFHL/R). After AVDD and DVDD are powered-up, the PDN pin should be "L" for 150ns. (2) The analog output corresponding to digital input has group delay (GD). (3) Analog outputs are floating (Hi-Z) in power-down mode. (4) Click noise occurs at the edge of PDN signal. This noise is output even if "0" data is input. (5) MCLK, BICK and LRCK clocks can be stopped in power-down mode (PDN pin= "L"). (6) Mute the analog output externally if click noise (3) adversely affect system performance The timing example is shown in this figure. (7) DZFL/R pins are "L" in the power-down mode (PDN pin = "L"). Figure 23. Power-down/up Sequence Example MS1648-E-03 2014/11 - 44 - [AK4490] Reset Function (1) RESET by RSTN bit = "0" When the RSTN bit = "0", the AK4490's digital block is powered down, but the internal register values are not initialized. In this time, the analog outputs go to VCML/R voltage and DZFL/DZFR pins are "H". Figure 24 shows an example of reset by RSTN bit. RSTN bit 3~4/fs (5) 2~3/fs (5) Internal RSTN bit Internal State Normal Operation Power-down D/A In (Digital) "0" data (1) D/A Out (Analog) Normal Operation Digital Block GD GD (3) (2) (3) (1) 2/fs(4) DZF (6) Notes: (1) The analog output corresponding to digital input has group delay (GD). (2) Analog outputs settle to VCOM voltage. (3) Small pop noise occurs at the edges(" ") of the internal timing of RSTN bit. This noise is output even if "0" data is input. (4) The DZF pins change to "H" when the RSTN bit becomes "0", and return to "L" at 2/fs after RSTN bit becomes "1". (5) There is a delay, 3~4/fs from RSTN bit "0" to the internal RSTN bit "0", and 2~3/fs from RSTN bit "1" to the internal RSTN bit "1". (6) Mute the analog output externally if click noise (3) and Hi-Z (2) adversely affect system performance Figure 24. Reset Sequence Example 1 MS1648-E-03 2014/11 - 45 - [AK4490] (2) RESET by MCLK or LRCK/WCK Stop The AK4490 is automatically placed in reset state when MCLK or LRCK is stopped during PDM mode (PDN pin = "H"), and the analog outputs are floating (Hi-Z). When MCLK and LRCK are input again, the AK4490 exits reset state and starts the operation. Zero detect function is disable when MCLK or LRCK is stopped. In DSD mode the AK4490 is in reset state when MCLK is stopped, and it is in reset state when MCLK and WCK are stopped in external digital filter mode. AVDD pin DVDD pin PDN pin (1) Internal State Power-down D/A In (Digital) Power-down Normal Operation Normal Operation (3) GD D/A Out (Analog) Digital Circuit Power-down (2) GD (4) Hi-Z (5) (2) (4) (4) (5) Clock In MCLK, BICK, LRCK Stop MCLK, BICK, LRCK External MUTE (6) (6) (6) Notes: (1) After AVDD and DVDD are powered-up, the PDN pin should be "L" for 150ns. (2) The analog output corresponding to digital input has group delay (GD). (3) The digital data can be stopped. Click noise after MCLK and LRCK are input again can be reduced by inputting "0" data during this period. (4) Click noise occurs within 3 ~ 4LRCK cycles from the riding edge ("") of the PDN pin or MCLK inputs. This noise occurs even when "0" data is input. (5) Clocks (MCLK, BICK, LRCK/WCK) can be stopped in the reset state (MCLK or LRCK/WCK is stopped). (6) Mute the analog output externally if click noise (4) influences system applications. The timing example is shown in this figure. Figure 25. Reset Sequence Example 2 MS1648-E-03 2014/11 - 46 - [AK4490] Synchronize Function The AK4490 has a function that resets the internal counter to synchronize with the external clock edge in a range of 3/256fs. Clock synchronize function becomes valid if SYNCE bit is set to "1" during operation in PCM mode or EXDF mode and input data of both L and R channels are "0" for 8129 times continuously or RSTN bit is "1". In PCM mode, the internal counter is synchronized with a falling edged of LRCK (rising edge of LRCK in I2C mode), and it is synchronized with a falling edge of WCK in EXDF mode. In this case, the analog output has the same voltage as VCML/R. Figure 26 shows a synchronizing sequence when the input data is "0" for 8192 times continuously. Figure 27 shows a synchronizing sequence by RSTN bit. (1) Synchronization by continuous "0" data input for 8192 times If the input data is "0" for 8192 times continuously, or if the data becomes "0" for 8192 times continuously by attenuation, the DZFL/DZFR pin goes to "H" and the synchronize function becomes valid. The synchronize function is enabled only when both L and R channels data are "0" for 8192 times continuously. Figure 26 shows a synchronizing sequence when the input data is "0" for 8192 times continuously. D/A In (Digital) SMUTE (1) (1) ATT_Level Attenuation - GD GD (4) AOUT DZF pin (2) 8192/fs (2) 8192/fs SYNC Operation (2) Internal Counter Reset Internal Data Reset GD SYNC Operation (2) (5) 4~5/fs (3) Note: (1) ATT_DATA ATT transition time. For example, this time is 7424LRCK cycles (1020/fs) at ATT_DATA=255 in Normal Speed Mode. (2) When both L and R channels data are "0" for 8192 times continuously, DZFL/R pins become "H" and the synchronize function is valid. (3) Internal data is fixed to "0" forcibly for 4 to 5/fs when internal counter is reset. (4) A click noise may occur when the internal counter is reset. This noise is output even if a "0" data is input. Mute the analog output externally if this click noise affects the system performance. (5) When the internal clock and external clock are in synchronization, the internal counter is not reset even if the synchronize function is valid. Figure 26. Synchronizing Sequence by Continuous "0" Data Input for 8192 Times MS1648-E-03 2014/11 - 47 - [AK4490] (2) Synchronization by RSTN bit If RSTN bit is set to "0", the output signal of the DZFL/DZFR pin becomes "H". Then, the DAC is reset 3 to 4/fs after the DZFL/DZFR pin = "H" and the analog output becomes the same voltage as VCML/R. The synchronize function becomes valid when both of the DZFL and DZFR pins output "H". Figure 27 shows a synchronizing sequence by RSTN bit. RSTN bit 3~4/fs (4) 2~3/fs (4) Internal RSTN bit Internal State Normal Operation D/A In (Digital) force"0" (2) (3) D/A Out (Analog) Normal Operation Digital Block Power-down GD GD (3) (5) (5) 2/fs(4) DZF SYNC Operation (1) Internal Counter Reset Internal Data Reset 4~5/fs (2) Note: (1) DZFL/R pin becomes "H" by a rising edge of RSTN bit, and becomes "L" 2/fs after a falling edge of internal signal of RSTN bit. The synchronize function is valid During the DZFL/R pin = "H". (2) Internal data is fixed to "0" forcibly for 4 to 5/fs when the internal counter is reset. (3) Since the analog output corresponding to digital input has group delay (GD), it is recommended to have a no-input period longer than the group delay before writing "0" to RSTN bit. (4) It takes 3 to 4/fs when falling to change the internal RSTN signal of the LSI after writing to RSTN bit. It also takes 3 to 4/fs when rising to change the internal RSTN signal of the LSI. The synchronize function becomes valid immediately when "0" is written to RSTN bit. Therefore, there is a case that the internal counter is reset before internal RSTN signal of the LSI is changed. (5) A click noise occurs on the rising or falling edge of the internal RSTN signal and when the internal counter is reset. This noise is output even if a "0" data is input. Mute the analog output externally if this click noise affects the system performance. Figure 27. Synchronizing Sequence by RSTN bit MS1648-E-03 2014/11 - 48 - [AK4490] Register Control Interface (1) 3-wire Serial Control Mode (I2C pin = "L") Pins (parallel control mode) or registers (serial control mode) can control the functions of the AK4490. In parallel control mode, the register setting is ignored, and in serial control mode the pin settings are ignored. When the state of the PSN pin is changed, the AK4490 should be reset by the PDN pin. The serial control interface is enabled by the PSN pin = "L". Internal registers may be written to through3-wire P interface pins: CSN, CCLK and CDTI. The data on this interface consists of Chip address (2-bits, C1/0), Read/Write (1-bit; fixed to "1"), Register address (MSB first, 5-bits) and Control data (MSB first, 8-bits). The data is output on a falling edge of CCLK and the data is received on a rising edge of CCLK. The writing of data is valid when CSN "". The clock speed of CCLK is 5MHz (max). Parallel Control Serial Control Mode Mode Audio Format Y Y Auto Setting Mode Y Y De-emphasis Y Y SMUTE Y Y DSD Mode Y EX DF I/F Y Zero Detection Y Sharp Roll off filter Y Y Slow Roll off filter Y Y Minimum delay Filter Y Y Digital Attenuator Y Table 28. Function List1 (Y: Available, -: Not available) Function Setting the PDN pin to "L" resets the registers to their default values. In serial control mode, the internal timing circuit is reset by the RSTN bit, but the registers are not initialized. CSN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CCLK CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 C1-C0: Chip Address (C1 bit =CAD1 pin, C0 bit =CAD0 pin) R/W: READ/WRITE (Fixed to "1", Write only) A4-A0: Register Address D7-D0: Control Data Figure 28. Control I/F Timing * The AK4490 does not support read commands in 3-wire serial control mode. * When the AK4490 is in power down mode (PDN pin = "L"), writing into control registers is prohibited. * The control data cannot be written when the CCLK rising edge is 15 times or less or 17 times or more during CSN is "L". MS1648-E-03 2014/11 - 49 - [AK4490] (2) I2C-bus Control Mode (I2C pin = "H") The AK4490 supports the fast-mode I2C-bus (max: 400kHz, Ver 1.0). (2)-1. WRITE Operations Figure 29 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START condition. A HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 35). After the START condition, a slave address is sent. This address is 7 bits long followed by the eighth bit that is a data direction bit (R/W). The most significant five bits of the slave address are fixed as "00100". The next bits are CAD1 and CAD0 (device address bits). This bit identifies the specific device on the bus. The hard-wired input pin (CAD1pins, CAD0 pin) sets these device address bits (Figure 30). If the slave address matches that of the AK4490, the AK4490 generates an acknowledge and the operation is executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 36). A R/W bit value of "1" indicates that the read operation is to be executed, and "0" indicates that the write operation is to be executed. The second byte consists of the control register address of the AK4490 and the format is MSB first. (Figure 31). The data after the second byte contains control data. The format is MSB first, 8bits (Figure 32). The AK4490 generates an acknowledge after each byte is received. Data transfer is always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL is HIGH defines a STOP condition (Figure 35). The AK4490 can perform more than one byte write operation per sequence. After receipt of the third byte the AK4490 generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the write cycle after the first data byte is transferred. After receiving each data packet the internal address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds "09H" prior to generating a stop condition, the address counter will "roll over" to "00H" and the previous data will be overwritten. The data on the SDA line must remain stable during the HIGH period of the clock. HIGH or LOW state of the data line can only be changed when the clock signal on the SCL line is LOW (Figure 37) except for the START and STOP conditions. S T A R T SDA S S T O P R/W= "0" Slave Address Sub Address(n) A C K Data(n) Data(n+1) A C K A C K Data(n+x) A C K A C K P A C K Figure 29. Data Transfer Sequence at I2C Bus Mode 0 0 1 0 0 CAD1 CAD0 R/W (CAD0 is set by the pin) Figure 30. The First Byte 0 0 0 A4 A3 A2 A1 A0 D1 D0 Figure 31. The Second Byte D7 D6 D5 D4 D3 D2 Figure 32. The Third Byte and After The Third Byte MS1648-E-03 2014/11 - 50 - [AK4490] (2)-2. READ Operations Set the R/W bit = "1" for the READ operation of the AK4490. After transmission of data, the master can read the next address's data by generating an acknowledge instead of terminating the write cycle after the receipt of the first data word. After receiving each data packet the internal address counter is incremented by one, and the next data is automatically taken into the next address. If the address exceeds "09H" prior to generating stop condition, the address counter will "roll over" to "00H" and the data of "00H" will be read out. The AK4490 supports two basic read operations: Current Address Read and Random Address Read. (2)-2-1. Current Address Read The AK4490 has an internal address counter that maintains the address of the last accessed word incremented by one. Therefore, if the last access (either a read or write) were to address "n", the next CURRENT READ operation would access data from the address "n+1". After receipt of the slave address with R/W bit "1", the AK4490 generates an acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal address counter by 1. If the master does not generate an acknowledge but generates a stop condition instead, the AK4490 ceases the transmission. S T A R T SDA S S T O P R/W= "1" Slave Address Data(n) A C K Data(n+1) A C K Data(n+2) A C K Data(n+x) A C K A C K P A C K Figure 33. Current Address Read (2)-2-2. Random Address Read The random read operation allows the master to access any memory location at random. Prior to issuing the slave address with the R/W bit "1", the master must first perform a "dummy" write operation. The master issues a start request, a slave address (R/W bit = "0") and then the register address to read. After the register address is acknowledged, the master immediately reissues the start request and the slave address with the R/W bit "1". The AK4490 then generates an acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an acknowledge but generates a stop condition instead, the AK4490 ceases the transmission. S T A R T SDA S S T A R T R/W= "0" Slave Address Sub Address(n) A C K S A C K S T O P R/W= "1" Slave Address Data(n) A C K Data(n+1) A C K Data(n+x) A C K A C K P A C K Figure 34. Random Address Read MS1648-E-03 2014/11 - 51 - [AK4490] SDA SCL S P start condition stop condition Figure 35. Start Condition and Stop Condition DATA OUTPUT BY TRANSMITTER not acknowledge DATA OUTPUT BY RECEIVER acknowledge SCL FROM MASTER 2 1 8 9 S clock pulse for acknowledgement START CONDITION Figure 36. Acknowledge (I2C Bus) SDA SCL data line stable; data valid change of data allowed Figure 37. Bit Transfer (I2C Bus) MS1648-E-03 2014/11 - 52 - [AK4490] Function List Function Attenuation Level Default 0dB Address 03H 04H 00H 00H 00H 01H 01H 01H 01H 01H 02H 02H Bit ATT7-0 PCM DSD EX DF I/F Y Y - Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y - - Y - Y Y Y Y Y - Y Y Y External Digital Filter I/F Mode Disable EXDF EX DF I/F mode clock setting 16fs(fs=44.1kHz) ESC Audio Data Interface Modes 24bit MSB justified DIF2-0 Data Zero Detect Enable Disable DZFE Data Zero Detect Mode Separated DZFM Minimum delay Filter Enable Sharp roll-off filter SD De-emphasis Response OFF DEM1-0 Soft Mute Enable Normal Operation SMUTE DSD/PCM Mode Select PCM mode DP Master Clock Frequency Select at 512fs DCKS DSD mode MONO mode Stereo mode select Stereo 02H MONO Inverting Enable of DZF "H" active 02H DZFB The data selection of L channel R channel 02H SELLR and R channel Table 29. Function List (Y: Available, -: Not available) MS1648-E-03 2014/11 - 53 - [AK4490] Register Map Addr 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H Register Name Control 1 Control 2 Control 3 Lch ATT Rch ATT Control4 Control5 Control6 Control7 Control8 D7 ACKS DZFE DP ATT7 ATT7 INVL DDM 0 0 0 D6 EXDF DZFM 0 ATT6 ATT6 INVR DML 0 0 0 D5 ECS SD DCKS ATT5 ATT5 0 DMR 0 0 0 D4 0 DFS1 DCKB ATT4 ATT4 0 DMC 0 0 0 D3 DIF2 DFS0 MONO ATT3 ATT3 0 DMRE 0 0 0 D2 DIF1 DEM1 DZFB ATT2 ATT2 0 0 0 0 0 D1 DIF0 DEM0 SELLR ATT1 ATT1 DFS2 DSDD 0 SC1 DSDF D0 RSTN SMUTE SLOW ATT0 ATT0 SSLOW DSDSEL0 SYNCE SC0 DSDSEL1 Notes: In 3-wire serial control mode, the AK4490 does not support read commands. The AK4490 supports read command in I2C-bus control mode. Data must not be written into addresses from 0AH to 1FH. When the PDN pin goes to "L", the registers are initialized to their default values. When RSTN bit is set to "0", only the internal timing is reset, and the registers are not initialized to their default values. When the state of the PSN pin is changed, the AK4490 should be reset by the PDN pin. Register Definitions Addr Register Name 00H Control 1 R(I2C)/W Default D7 ACKS R/W 0 D6 EXDF R/W 0 D5 ECS R/W 0 D4 0 R 0 D3 DIF2 R/W 0 D2 DIF1 R/W 1 D1 DIF0 R/W 0 D0 RSTN R/W 0 RSTN: Internal Timing Reset 0: Reset. All registers are not initialized. (default) 1: Normal Operation Writing "0" to this bit resets the internal timing circuit but register values are not initialized. When the PSN pin = "H", the AK4490 operates regardless of this register setting. DIF2-0: Audio Data Interface Modes (Table 20) Initial value is "010" (Mode 2: 24-bit MSB justified). ECS: EX DF I/F mode clock setting (Table 21) 0: WCK=768kHz mode (default) 1: WCK=384kHz mode EXDF: External Digital Filter I/F Mode (Serial mode only) 0: Disable: Internal Digital Filter mode (default) 1: Enable: External Digital Filter mode ACKS: Master Clock Frequency Auto Setting Mode Enable (PCM only) 0: Disable: Manual Setting Mode (default) 1: Enable: Auto Setting Mode When ACKS bit = "1", MCLK frequency and the sampling frequency are detected automatically. MS1648-E-03 2014/11 - 54 - [AK4490] Addr Register Name 01H Control 2 R(I2C)/W Default D7 DZFE R/W 0 D6 DZFM R/W 0 D5 SD R/W 1 D4 DFS1 R/W 0 D3 DFS0 R/W 0 D2 DEM1 R/W 0 D1 DEM0 R/W 1 D0 SMUTE R/W 0 SMUTE: Soft Mute Enable 0: Normal Operation (default) 1: DAC outputs soft-muted. DEM1-0: De-emphasis Response Initial value is "01" (OFF). DFS1-0: Sampling Speed Control (Table 9) Initial value is "000" (Normal Speed). Click noise occurs when DFS2-0 bits are changed. (05H, D1: DFS2 bit ) SD: DFS2 0 0 DFS1 0 0 0 1 0 1 1 1 1 1 0 0 1 1 DFS0 0 1 Sampling Rate (fs) Normal Speed Mode 30kHz 54kHz (default) Double Speed Mode 54kHz 108kHz 120kHz 0 Quad Speed Mode 216kHz 1 Reserved 0 Oct Speed Mode 384kHz 1 Hex Speed Mode 768kHz 0 Reserved 1 Reserved Table 9. Sampling Speed (Manual Setting Mode @Serial Mode) Minimum delay Filter Enable 0: Traditional filter 1: Short delay filter (default) SD 0 0 1 1 SLOW Mode 0 Sharp roll-off filter 1 Slow roll-off filter 0 Short delay sharp roll off filter 1 Short delay slow roll off filter Table 14. Digital Filter Setting (default) DZFM: Data Zero Detect Mode 0: Channel Separated Mode (default) 1: Channel ANDed Mode If the DZFM bit is set to "1", the DZF pins of both L and R channels go to "H" only when the input data at both channels are continuously zeros for 8192 LRCK cycles. DZFE: Data Zero Detect Enable 0: Disable (default) 1: Enable Zero detect function can be disabled by DZFE bit "0". In this case, the DZF pins of both channels are always "L". MS1648-E-03 2014/11 - 55 - [AK4490] Addr Register Name 02H Control 3 R(I2C)/W Default SLOW: D7 DP R/W 0 D6 0 R 0 D5 DCKS R/W 0 D4 DCKB R/W 0 D3 MONO R/W 0 D2 DZFB R/W 0 D1 SELLR R/W 0 D0 SLOW R/W 0 Slow Roll-off Filter Enable 0: Sharp roll-off filter (default) 1: Slow roll-off filter SD 0 0 1 1 SLOW Mode 0 Sharp roll-off filter 1 Slow roll-off filter 0 Short delay sharp roll off filter 1 Short delay slow roll off filter Table 14. Digital Filter Setting (default) SELLR: The data selection of L channel and R channel, when MONO mode 0: All channel output R channel data, when MONO mode. (default) 1: All channel output L channel data, when MONO mode. It is enabled when MONO bit is "1", and outputs Rch data to both channels when "0", outputs Lch data to both channels when "1". DZFB: Inverting Enable of DZF 0: DZF pin goes "H" at Zero Detection (default) 1: DZF pin goes "L" at Zero Detection DZFE 0 DZFB 0 1 0 1 1 Data not zero Zero detect not zero DZF-pin L H L H H Zero detect L Table 25. Zero Detect Function and DZF Pin Output MONO: MONO mode Stereo mode select 0: Stereo mode (default) 1: MONO mode When MONO bit is "1", MONO mode is enabled. DCKB: Polarity of DCLK (DSD Only) 0: DSD data is output from DCLK falling edge. (default) 1: DSD data is output from DCLK rising edge. DCKS: Master Clock Frequency Select at DSD mode (DSD only) 0: 512fs (default) 1: 768fs DP: DSD/PCM Mode Select 0: PCM Mode (default) 1: DSD Mode When D/P bit is changed, the AK4490 should be reset by RSTN bit. MS1648-E-03 2014/11 - 56 - [AK4490] Addr Register Name 03H Lch ATT 04H Rch ATT R(I2C)/W Default D7 ATT7 ATT7 R/W 1 D6 ATT6 ATT6 R/W 1 D5 ATT5 ATT5 R/W 1 D4 ATT4 ATT4 R/W 1 D3 ATT3 ATT3 R/W 1 D2 ATT2 ATT2 R/W 1 D1 ATT1 ATT1 R/W 1 D0 ATT0 ATT0 R/W 1 ATT7-0: Attenuation Level 256 levels, 0.5dB step Data FFH FEH FDH : : 02H 01H 00H Attenuation 0dB -0.5dB -1.0dB : : -126.5dB -127.0dB MUTE (-) The transition between set values is soft transition of 7425 levels. It takes 7424/fs (168ms@fs=44.1kHz) from FFH (0dB) to 00H (MUTE). If the PDN pin goes to "L", the ATTs are initialized to FFH. The ATTs are FFH when RSTN bit= "0". When RSTN return to "1", the ATTs fade to their current value. This digital attenuator is independent of soft mute function. Addr Register Name 05H Control 4 R(I2C)/W Default D7 INVL R/W 0 D6 INVR R/W 0 D5 0 R 0 D4 0 R 0 D3 0 R 0 D2 0 R 0 D1 DFS2 R/W 0 D0 SSLOW R/W 0 SSLOW: Super Slow Roll-off Filter Enable 0: Disable (default) 1: Enable DFS2: Sampling Speed Control (Table 9) Initial value is "000" (Normal Speed). Click noise occurs when DFS2-0 bits are changed. (01H, D4, D3: DFS1-0 bits) DFS2 0 0 0 0 1 1 1 1 DFS1 DFS0 Sampling Rate (fs) 0 0 Normal Speed Mode 30kHz 54kHz 0 1 Double Speed Mode 54kHz 108kHz 1 0 Quad Speed Mode 120kHz 216kHz 1 1 Reserved 0 0 Oct Speed Mode 384kHz 0 1 Hex Speed Mode 768kHz 1 0 Reserved 1 1 Reserved Table 9. Sampling Speed (Manual Setting Mode @Serial Mode) MS1648-E-03 (default) 2014/11 - 57 - [AK4490] INVR: AOUTR Output Phase Inverting 0: Disable (default) 1: Enable INVL: AOUTL Output Phase Inverting 0: Disable (default) 1: Enable Addr Register Name 06H Control 5 R(I2C)/W Default D7 DDM R/W 0 D6 DML R/W 0 D5 DMR R/W 0 D4 DMC R/W 0 D3 DMRE R/W 0 D2 0 R 0 D1 DSDD R/W 0 D0 DSDSEL0 R/W 0 DSDSEL1-0: DSD Sampling Speed Control (See also Control 7 register.) DSDSEL1 bit DSDSEL0 bit DSD data stream 0 0 2.8224MHz 0 1 5.6448MHz 1 0 11.2896MHz 1 1 Reserved Table 16. DSD Sampling Speed Control (default) DSDD: DSD Play Back Path Control DSDD Mode 0 Normal Path (default) 1 Volume Bypass Table 17. DSD Play Back Mode Control DMRE: DSD Mute Release 0: Hold (default) 1: Release Mute This register is only valid when DDM bit = "1" and DMC bit = "1". When the AK4490 mutes DSD data by DDM and DMC bits settings, the mute is released by setting DMRE bit to "1". DMC: DSD Mute Control 0: Auto Return (default) 1: Mute Hold (manual return) This register is only valid when DDM bit = "1". It selects the mute releasing mode of when the DSD data level becomes under full-scale after the AK4490 mutes DSD data by DDM bit setting. DMR/DML This register outputs detection flag when a full scale signal is detected at DSDR/L channel. DDM: DSD Data Mute 0: Disable (default) 1: Enable The AK4490 has an internal mute function that mutes the output when DSD audio data becomes all "1" or all "0" for 2048 Samples (1/fs). DDM bit controls this function. MS1648-E-03 2014/11 - 58 - [AK4490] Addr Register Name 07H Control 6 R(I2C)/W Default D7 0 R 0 D6 0 R 0 D5 0 R 0 D4 0 R 0 D3 0 R 0 D2 0 R 0 D1 0 R 0 D0 SYNCE R/W 0 SYNCE: Synchronization control 0: Disable (default) 1: Enable This register enables the function that synchronizes multiple AK4490s when using more than one AK4490s in a system. Addr Register Name 08H Control 7 R(I2C)/W Default D7 0 R 0 D6 0 R 0 D5 0 R 0 D4 0 R 0 D3 0 R 0 D2 0 R 0 D1 SC1 R/W 0 D2 0 R 0 D1 DSDF R/W 0 D0 SC0 R/W 0 SC1-0: Sound control bit SC1 0 0 1 1 Addr Register Name 09H Control 8 R(I2C)/W Default SC0 Sound Mode 0 Sound Setting 1 1 Sound Setting 2 0 Sound Setting 3 1 Reserved Table 27. SC1-0 bits Control D7 0 R 0 D6 0 R 0 D5 0 R 0 (default) D4 0 R 0 D3 0 R 0 D0 DSDSEL1 R/W 0 DSDSEL1-0: DSD Sampling Speed Control (See also Control 4 register.) DSDSEL1 DSDSEL0 DSD data stream 0 0 2.8224MHz (default) 0 1 5.6448MHz 1 0 11.2896MHz 1 1 Reserved Table 16. DSD Sampling Speed Control When DSDD bit= "1", the filter characteristics can be switched between 50kHz and 150kHz by DSDF bit. DSDD bit DSDF bit Cut Off Filter 0 0 50kHz (default) 0 1 Reserved 1 0 50kHz 1 1 150kHz Table 18. DSD Filter Select MS1648-E-03 2014/11 - 59 - [AK4490] 10. Recommended External Circuits Figure 38 shows the system connection diagram. Figure 40, Figure 41 and Figure 42 show the analog output circuit examples. The evaluation board (AKD4490) demonstrates the optimum layout, power supply arrangements and measurement results. NC 37 VCML 38 VREFLL 39 VREFLL 40 VREFHL 41 NC 43 0.1u VREFHL 42 DVSS 47 10u 0.1u 1 NC 2 PDN 3 BICK VDDL 34 4 SDATA VDDL 33 5 LRCK 6 WCK 7 SMUTE/CSN 8 SD/CCLK/SCL 9 SLOW/CDTI/SDA AOUTLP 36 AK4490 AOUTLN 35 VSSR 30 N Rch LPF Rch Mute Rch Out 0.1u 10u + 0.1u 0.1u 220u 10u Analog Ground 0.1u 10u + 24 NC AOUTRP 25 23 VCMR 22 VREFLR 21 VREFLR 16 DEM1 15 DEM0 14 I2C 20 VREFHR AOUTRN 26 18 NC VDDR 27 11 DIF1/DZFR 13 PSN Lch Out VSSR 29 VDDR 28 Digital Ground Lch Mute VSSL 32 10 DIF0/DZFL 12 DIF2/CAD0 Lch LPF VSSL 31 19 VREFHR Controller 220u 17 ACKS/CAD1 Micro- MCLK 46 DSP DVDD 48 0.1u 10u 0.1u AVSS 45 + AVDD 44 10u Analog 5.0V Analog 3.3V Digital 3.3V + Electrolytic Capacitor Ceramic Capacitor Notes: - Chip Address = "00". BICK = 64fs, LRCK = fs - Power lines of AVDD and DVDD should be distributed separately from the point with low impedance of regulator etc. - AVSS, DVSS, VSSL, VSSR, VREFLL and VREFLR must be connected to the same analog ground plane. - When AOUT drives a capacitive load, some resistance should be connected in series between AOUT and the capacitive load. - All input pins except pull-down/pull-up pins should not be allowed to float. Figure 38. Typical Connection Diagram (AVDD=3.3V, VDDL/R=5V, DVDD=3.3V, Serial control mode) MS1648-E-03 2014/11 - 60 - [AK4490] VDDR 27 AOUTRN 26 N AOUTRP 25 VSSR 29 VDDR 28 VSSL 31 VSSR 30 VSSL 32 VDDL 33 VDDL 34 37 NC AOUTLP 36 Analog Ground AOUTLN 35 38 VCML System VCMR 23 40 VREFLL VREFLR 22 VREFLR 21 41 VREFHL Controller NC 24 39 VREFLL 42 VREFHL VREFHR 20 AK4490 43 NC VREFHR 19 46 MCLK DEM1 16 DEM0 15 11 DIF1/DZFR 6 WCK 5 LRCK 4 SDATA 3 BICK NC 1 2 PDN 48 DVDD 10 DIF0/DZFL 47 DVSS 9 SLOW/CDTI/SDA ACKS/CAD1 17 8 SD/CCLK/SCL NC 18 45 AVSS 7 SMUTE/CSN 44 AVDD 12 DIF2/CAD0 Digital Ground I2C 14 PSN 13 Figure 39. Ground Layout 1. Grounding and Power Supply Decoupling To minimize coupling by digital noise, decoupling capacitors should be connected to AVDD and DVDD respectively. VREFHL/R and VDDL/R are supplied from analog supply in system, and AVDD and DVDD are supplied from digital supply in system. Power lines of VREFHL/R and VDDL/R should be distributed separately from the point with low impedance of regulator etc. AVSS, DVSS, VSSL and VSSR must be connected to the same analog ground plane. Decoupling capacitors for high frequency should be placed as near as possible to the supply pin. 2. Voltage Reference The differential voltage between VREFHL/R and VREFLL/R sets the analog output range. The VREFHL/R pin is normally connected to AVDD, and the VREFLL/R pin is normally connected to VSS1/2/3. VREFHL/R and VREFLL/R should be connected with a 0.1F ceramic capacitor as near as possible to the pin to eliminate the effects of high frequency noise. No load current may be drawn from VCML/R pin. All signals, especially clocks, should be kept away from the VREFHL/R and VREFLL/R pins in order to avoid unwanted noise coupling into the AK4490. 3. Analog Outputs The analog outputs are full differential outputs and 2.8Vpp (typ, VREFHL/R VREFLL/R = 5V) centered around VDDR/2 and VDDL/2 voltages. The differential outputs are summed externally, VAOUT = (AOUT+) (AOUT) between AOUT+ and AOUT. If the summing gain is 1, the output range is 5.6Vpp (typ, VREFHL/R VREFLL/R = 5V). The bias voltage of the external summing circuit is supplied externally. The input data format is 2's complement. The output voltage (VAOUT) is a positive full scale for 7FFFFFH (@24bit) and a negative full scale for 800000H (@24bit). The ideal VAOUT is 0V for 000000H(@24bit). The internal switched-capacitor filters attenuate the noise generated by the delta-sigma modulator beyond the audio passband. Figure 40 shows an example of external LPF circuit summing the differential outputs by an op-amp. Figure 41 shows an example of differential outputs and LPF circuit example by three op-amps. MS1648-E-03 2014/11 - 61 - [AK4490] AK4490 1.5k AOUT- 1.5k 390 1n +Vop 2.2n 1.5k AOUT+ 1.5k Analog Out 390 1n -Vop Figure 40. External LPF Circuit Example 1 for PCM (fc = 99.2kHz, Q=0.704) Frequency Response Gain 20kHz 0.011dB 40kHz 0.127dB 80kHz 1.571dB Table 30. Frequency Response of External LPF Circuit Example 1 for PCM +15 3.3n + 100u 180 AOUTL- + 10k 330 7 3 2 + * 4 3.9n -15 10u 0.1u 6 NJM5534D + 10u 0.1u 620 + + 330 7 3 + 2 4 3.9n 680 100 6 1.0n NJM5534D Lch g 10u 0.1u 6 NJM5534D 1.2k 10k AOUTL+ 180 2 - 4 + 3 7 560 620 3.3n 100u +10u 1.0n 1.2k 680 0.1u 560 + 0.1u 10u + 10u 0.1u Figure 41. External LPF Circuit Example 2 for PCM 1st Stage 2nd Stage Total Cut-off Frequency 182kHz 284kHz Q 0.637 Gain +3.9dB -0.88dB +3.02dB 20kHz -0.025 -0.021 -0.046dB Frequency 40kHz -0.106 -0.085 -0.191dB Response 80kHz -0.517 -0.331 -0.848dB Table 31. Frequency Response of External LPF Circuit Example 2 for PCM MS1648-E-03 2014/11 - 62 - [AK4490] It is recommended for SACD format book (Scarlet Book) that the filter response at SACD playback is an analog low pass filter with a cut-off frequency of maximum 50kHz and a slope of minimum 30dB/Oct. The AK4490 can achieve this filter response by combination of the internal filter (Table 32) and an external filter (Figure 42). Frequency Gain 20kHz 0.4dB 50kHz 2.8dB 100kHz 15.5dB Table 32. Internal Filter Response at DSD Mode 2.0k 1.8k 4.3k AOUT1.0k 270p 2.8Vpp 2200p +Vop 3300p 2.0k 1.8k 1.0k + AOUT+ + - 2.8Vpp 4.3k 270p Analog Out 6.34Vpp -Vop Figure 42. External 3rd Order LPF Circuit Example for DSD Frequency Gain 20kHz 0.05dB 50kHz 0.51dB 100kHz 16.8dB DC gain = 1.07dB Table 33. 3rd Order LPF (Figure 42) Response MS1648-E-03 2014/11 - 63 - [AK4490] 11. Package Outline Dimensions 48-pin LQFP (Unit mm) Material & Lead finish Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy, Halogen (bromine and chlorine) free Cu Solder (Pb free) plate MS1648-E-03 2014/11 - 64 - [AK4490] Marking AKM AK4490EQ XXXXXXX 0VT 48 1 1) AKM Logo 2) Pin #1 indication 3) Date Code: XXXXXXX(7 digits) 4) Marking Code: AK4490EQ 12. Revision History Date (Y/M/D) Revision 14/04/30 00 14/07/14 01 Reason First Edition Spec change Page Contents 1 Error correction 7 2. Features VDD1/2=4.755.25VVDD1/2=4.757.2V 5. Pin Configurations and Functions Pin Functions 23 VCMR Normally connected to VREFLL with a 10uF electrolytic cap. Normally connected to VREFLR with a 10uF electrolytic cap. 38 VCML Normally connected to VREFLR with a 10uF electrolytic cap. Normally connected to VREFLL with a 10uF electrolytic cap. MS1648-E-03 2014/11 - 65 - [AK4490] 12. Revision History Date (Y/M/D) Revision 14/07/14 01 Reason Error Correction Specification Change Page 4 Error Correction 11 9 15 27 32 41 Description Addition Error Correction Description Addition 14/08/07 02 Error Correction Specification Change Error Correction Contents 4. Block Diagram "Volume bypass" line is added. 6. Absolute Maximum Ratings Power Supply, ADDL/R: 7.5 7.2V (max.) Note 3. Connect at least 0.1uF or more decoupling capacitors between VDDL/VDDR and VSSL/VSSR to suppress affections by a static electricity noise or an over voltage (includes over shooting) that exceeds absolute maximum ratings. 7. Recommended Operating Conditions Analog, ADDL/R: 5.25 7.2V (max.) Note14. "to input register" was removed. Note15. "to input register" was removed. 9. Functional Descriptions System Clock "VDDR/2 and DVDDL/2 voltages (typ)"" Hi-z state" 9. Functional Descriptions [2] DSD mode "VDDR/2 and DVDDL/2 voltages (typ)"" Hi-z state" Description is removed after Table18 of page 32. 42 Table 27. Mode 1Sound Setting 1 2Sound Setting 2 3Sound Setting 3 4Reserved " Characteristics (DSD) 49 Register Control Interface 54 Register Map "or the MCLK is not provided" is removed. "In 3-wire serial control mode, the AK4490 does not support read commands." "The AK4490 supports read commands in I2C-bus control mode." 54-58 Register Definitions "R(I2C)/W" is added each address. 1 2. Features "Filter bypass mode" is removed. 6. Absolute Maximum Ratings Power Supply, ADDL/R: 7.2 7.5V (max.) 9. Functional Descriptions System Clock 1. Manual Setting Mode (ACKS pin = "L") DFS1 bit is fixed to "0". DFS1-0 bit is fixed to "00". 9 28 MS1648-E-03 2014/11 - 66 - [AK4490] 12. Revision History Date (Y/M/D) Revision 14/08/07 02 Reason Error Correction Page 28 30 54 14/11/14 03 Error Correction 20 Contents 9. Functional Descriptions System Clock 1. Manual Setting Mode (ACKS pin = "L") Table 3 88.2kHz and 96kHz descriptions are removed. 9. Functional Descriptions System Clock 2.Auto Setting Mode (ACKS bit = "1) DFS1-0 bits are ignored. DFS2-0 bits are ignored. ECS: Ex DF I/F Mode Clock Setting 0: Disable: Internal Digital Filter Mode (default) 0: WCK=768kHz mode (default) 1: Enable: External Digital Filter Mode 1: WCK=384kHz mode Master Clock Timing "Minimum Pulse Width" is added External Digital Filter Mode "WCK Period" is added MS1648-E-03 2014/11 - 67 - [AK4490] IMPORTANT NOTICE 0. Asahi Kasei Microdevices Corporation ("AKM") reserves the right to make changes to the information contained in this document without notice. When you consider any use or application of AKM product stipulated in this document ("Product"), please make inquiries the sales office of AKM or authorized distributors as to current status of the Products. 1. All information included in this document are provided only to illustrate the operation and application examples of AKM Products. AKM neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of AKM or any third party with respect to the information in this document. You are fully responsible for use of such information contained in this document in your product design or applications. AKM ASSUMES NO LIABILITY FOR ANY LOSSES INCURRED BY YOU OR THIRD PARTIES ARISING FROM THE USE OF SUCH INFORMATION IN YOUR PRODUCT DESIGN OR APPLICATIONS. 2. The Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact, including but not limited to, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for the above use unless specifically agreed by AKM in writing. 3. Though AKM works continually to improve the Product's quality and reliability, you are responsible for complying with safety standards and for providing adequate designs and safeguards for your hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of the Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. 4. Do not use or otherwise make available the Product or related technology or any information contained in this document for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). When exporting the Products or related technology or any information contained in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. The Products and related technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 5. Please contact AKM sales representative for details as to environmental matters such as the RoHS compatibility of the Product. Please use the Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. AKM assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 6. Resale of the Product with provisions different from the statement and/or technical features set forth in this document shall immediately void any warranty granted by AKM for the Product and shall not create or extend in any manner whatsoever, any liability of AKM. 7. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of AKM. MS1648-E-03 2014/11 - 68 -