Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 DESCRIPTION PT2389 is a 2-channel digital preset equalizer utilizing CMOS Technology. It provides 5 different sound selections, namely: Flat/Normal, Rock, Pops, Classic and Jazz. Bass Booster and 3D Effects may be added to any of 5 sound selections, thereby creating more audio versatility. PT2389 provides two types of key selection mode, namely: the Direct and the Cyclic. Pin assignment and application circuit are optimized for cost saving advantages and easy PCB layout. FEATURES z z z z z z z z z z CMOS Technology Low Total Harmonic Distortion and High S/N Ratio: THD + N < 0.01%, S/N > 95 dB LED Display Output Mode Least External Components 5 Sound Selections Provided: Flat/Normal, Classic, Rock, Pops, and Jazz Bass Booster Function & 3D Effect Provided 2-Channel Output Wide Operating Voltage Range: 5 ~ 9 V Direct or Cyclic Key Selection is Provided Available in 24 Pins, DIP, SOP, SSOP APPLICATIONS z z z z z Walkman Car Audio Mini Compo Multimedia Audio Components MPEG Card PT2389 v1.3 -1- September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 BLOCK DIAGRAM PIN CONFIGURATION PT2389 v1.3 -2- September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 PIN DESCRIPTION Pin Name INL I/O BL1 -- BL2 -- TL -- OUTL VCC Bias GND SEL O -- -- -- Mute Cyc BB 3D BLED Flat Rock Pops Classic Jazz OUTR I I/O O I/O I/O I/O I/O I/O O TR BR2 BR1 INR I PT2389 v1.3 Description Left Channel Input Left Bass Control Pin 1 A capacitor is connected between this pin and BL2 Left Bass Control Pin 2 A capacitor is connected between this pin and BL1 Left Treble Control Pin A capacitor is connected between this pin and OUTL Left Channel Output Pin Positive Supply Voltage A capacitor is connected between this pin and GND Ground Select Control Pin Mute pin The Mute pin can eliminate the noise when mode charging occurs. A capacitor is connected between this pin and GND Cyclic Select Pin Bass Booster Control Input Pin 3D Effect Control Input Pin/Output LED Pin Bass Booster Display Pin Flat Mode Display & Control Input Pin Rock Mode Display & Control Input Pin Pops Mode Display & Control Input Pin Classic Mode Display & Control Input Pin Jazz Mode Display & Control Input Pin Right Channel Output Pin Right Treble Control Pin A capacitor is connected between this pin and OUTR Right Bass Control Pin 2 A capacitor is connected between this pin and BR1 Right Bass Control Pin 1 A capacitor is connected between this pin and BR2 Right Channel Input Pin -3- Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 FUNCTION DESCRIPTION PT2389 is a 5-Mode Preset Equalizer IC with a Bass Booster and 3D Effects. It has 2 types of key selection mode, namely: Direct and Cyclic. The Direct or Cyclic Key Selection Mode is determined by the SEL Pin. Please refer to the table below: SEL pin Direct Low Cyclic * Floating/High Description Press Flat keyFlat mode Press Rock keyRock mode Press Pops keyPops mode Press Classic keyClassic mode Press Jazz keyJazz mode * Press Cyc Key Note: The Bass Booster Function and the 3D Effect can be controlled in the same manner under the Direct or the Cyclic Key Selection Mode. To turn the Bass Booster On or Off, press the BB Key. To turn the 3D Effect On or Off, press the 3D Key. CYCLIC KEY SELECTION MODE Press Cyc Power On Press Cyc Flat Mode Rock Mode Pops Mode BB Key, 3D Key Control Bass Booster, 3D Effect On or Off Press Cyc Jazz Mode Press Cyc Press Cyc Classic Mode After power on, PT2389 is Flat Mode, under this mode, any of the sound selections (Flat, Rock, Pops, Classic, Jazz) may be selected by pressing the CYC Key. BB key and 3D key is the switch of Bass Booster and 3D Effect (Bass Booster and 3D Effect if Off when Power On) PT2389 v1.3 -4- September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 DIRECT KEY SELECTION MODE Rock Mode Power On Flat Mode Pops Mode Jazz Mode Classic Mode Bass Booster 3D Effect Control After power on, PT2389 is Flat Mode, under this mode, you can directly select the sound selection you like. The Bass Booster Function and 3D Effect can switch On or Off in any mode. PT2389 v1.3 -5- September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 FREQUENCY RESPONSE The following figures illustrate the various frequency responses under the various sound selections. Note: Flat Mode PT2389 v1.3 Flat+3D Flat+BB -6- Flat+3D+BB September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 Note: Rock Mode Rock+3D Rock+BB Rock+3D+BB Note: Pops Mode PT2389 v1.3 Pops+3D Pops+BB -7- Pops+3D+BB September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 Note: Classic Mode Classic+3D Classic+BB Classic+3D+BB Jazz Mode Jazz+3D Jazz+BB Jazz+3D+BB Note: PT2389 v1.3 -8- September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 Different sound selections exhibit different frequency gains and different frequency levels. Please refer to the table below. Mode Flat Rock Pops Classic Jazz Flat+Bass Booster Rock+Bass Booster Pops+Bass Booster Classic+Bass Booster Jazz+Bass Booster Flat+3D Rock+3D Pops+3D Classic+3D Jazz+3D Flat+BB+3D Rock+ BB+3D Pops+ BB+3D Classic+ BB+3D Jazz+ BB+3D PT2389 v1.3 f=80Hz 3 14 8 8.5 14.5 10 18.5 12.5 13 18.5 7 18 11.5 12 18 14 22.5 16.5 16.5 22.5 -9- Typ. f=1KHz 3 6.5 6 7 7.5 5 7 6.5 7 7.5 7 10 9.5 9.5 10.5 8.5 10.5 10 10.5 11 f=10KHz 3 12.5 12.5 7.5 10.5 4 12.5 12.5 8 10.5 7 16 16 11 14 7.5 16.5 16 11 14 Unit dB September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 TREBLE AND BASS ADJUSTMENT It is general knowledge that different individuals have different listening preferences. The application circuit of PT2389 included in this specification has been designed for the taste general listening public; however, you can make the necessary adjustment to suit your personal taste. Please refer to the sections below. TREBLE ADJUSTMENT The Treble adjustment is made by changing the value of the 2 capacitors connected between TL -- OUTL pins and TR -- OUTR pins. Please refer to the diagram below. As the capacitor value becomes bigger, the treble of the gain frequency curve is shifted down. Likewise, as the capacitor value becomes smaller, the treble gain frequency curve shifts the opposite direction. Referring to the diagram above, we see that at 8dB, different capacitor values exhibit different frequency responses. Capacitor value 1800 pF has a lower frequency gain response than 1200 pF capacitor. 1800pF 1500pF 1200pF Hz TL - OUTL Capacitors vs. Frequency Response Note: 1200pF PT2389 v1.3 1500pF - 10 - 1800pF September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 BASS ADJUSTMENT Bass adjustments can be made by changing the values of the capacitors connected between BL1 -- BL2 pins, and BR1 -- BR2 pins. The larger the capacitor value used, the frequency response curve shifts down. Likewise, the smaller the capacitor value, the frequency response curve shifts the opposite direction. Please refer to the diagram below. 0.056uF 0.068uF 0.1uF HZ BL1 - BL2 Capacitor vs. Frequency Response Curve Note: 0.1F PT2389 v1.3 0.068F - 11 - 0.056F September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 ABSOLUTE MAXIMUM RATINGS Parameter Supply Voltage Operating Temperature Storage Temperature Input Voltage Symbol Vcc Topr Tstg Vi Ratings 12 -40 +85 -65 +150 -0.3Vcc+0.3 Unit V V ELECTRICAL CHARACTERISTICS Unless otherwise specified, Vcc=9VVi=1Vrmsf=1KHzTemp=27 Parameter Operating Voltage Operating Current Max. Output Voltage Symbol Vcc Icc VOM Output Noise VNO Total Harmonic Distortion THD Input Impedance Output Impedance High Level Input Voltage Low Level Input Voltage RIN ROUT VIH VIL Max. Input Voltage VIMAX PT2389 v1.3 Conditions Vcc=9V, Vi=0V Flat Mode Vcc=9V Vcc=9V, Vi=0V BW=2020KHz A-Weighting Vcc=9V, Vi=0.2Vrms BW=2020KHz Vcc=9V Vcc=9V Vcc=9V Vcc=9V Vcc=9V, Flat ModeBB & 3D off - 12 - Min. 5 Typ. 9 20 -90 70 100 40 Max. 10 2.5 Unit V mA Vrms -98 dB 0.01 % 140 80 0.7Vcc K V V 2.0 Vrms 0.3Vcc September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 APPLICATION CIRCUIT DIRECT KEY MODE Note: Please use 1500pF0.068F Mylar Capacitor PT2389 v1.3 - 13 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 CYCLIC KEY MODE Note: Please use 1500pF0.068F Mylar Capacitor PT2389 v1.3 - 14 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 ORDER INFORMATION Valid Part Number PT2389 PT2389-S PT2389-SN PT2389 (L) PT2389-S (L) PT2389-SN (L) Package Type 24 Pins, DIP, 300 mil 24 Pins, SOP, 300 mil 24 Pins, SSOP, 150 mil 24 Pins, DIP, 300 mil 24 Pins, SOP, 300 mil 24 Pins, SSOP, 150 mil Top Code PT2389 PT2389-S PT2389-SN PT2389 PT2389-S PT2389-SN Notes: 1. (L) = Lead Free 2. The Lead Free mark is put in front of the date code. PT2389 v1.3 - 15 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 PACKAGE INFORMATION 24 PINS, DIP (300 MIL) PT2389 v1.3 - 16 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect Symbols A A1 A2 b b1 b2 b3 c c1 D D1 E E1 e eA eB eC L Min. 0.015 0.115 0.014 0.014 0.045 0.030 0.008 0.008 1.160 0.005 0.300 0.240 0.000 0.115 PT2389 Nom. Max. 0.210 0.130 0.018 0.018 0.060 0.039 0.010 0.010 1.185 0.195 0.022 0.020 0.070 0.045 0.014 0.011 1.195 0.310 0.250 0.100 bsc. 0.300 bsc. 0.325 0.280 0.130 0.430 0.060 0.150 Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. All dimensions are in INCHES. Dimensioning and tolerancing per ANSI Y 14.5-1982. Dimension "A", "A1" and "L" are measured with the package seated in JEDEC Seating Plane Gauge GS-3. "D", "D1" and "E1" dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch. "E" and "eA" measured with the leads constrained to be perpendicular to datum -c- . "eB" and "eC" are measured at the lead tips with the leads unconstrained. N is the number of terminal positions. (N=24) Pointed or rounded lead tips are preferred to ease insertion. "b2" and "b3" maximum dimensions are not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm) Distance between leads including Dambar protrusions to be 0.005 inch. minimum. Datum plane -H- coincident with the bottom of lead, where lead exits body. Refer to JEDEC MS-001, Variation BE. JEDEC is the trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION. PT2389 v1.3 - 17 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 24 PINS, SOP (300 MIL) Symbols A A1 B C D E e H h L PT2389 v1.3 Min. 2.35 0.10 0.33 0.23 15.20 7.40 Nom. Max. 2.65 0.30 0.51 0.32 15.60 7.60 1.27 bsc. 10.00 0.25 0.40 0 - 18 - 10.65 0.75 1.27 8 September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. Dimensioning and tolerancing per ANSI Y 14.5-1982. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold Flash, protrusion or gate burrs shall not exceed 0.15mm (0.006 in)per side. Dimension "E" does not include interlead flash protrusions. Interlead flash or protrusions shall not exceed 0.25 mm (0.010 in) per side. The chamfer on the body is optional. It is not present, a visual index feature must be located within the crosshatched area. "L" is the length of the terminal for soldering to a substrate. "N" is the number of terminal position. (N=24) The lead width "B" as measured 0.36 mm (0.014 in) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.24 in). Controlling dimension: MILLIMETER. Refer to JEDEC MS-013, Variation AD. JEDEC is the trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION. PT2389 v1.3 - 19 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 24 PINS, SSOP (150MIL) PT2389 v1.3 - 20 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 v1.3 - 21 - PT2389 September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect Symbol A A1 A2 b b1 c c1 D E E1 e L L1 L2 R R1 1 2 aaa bbb ccc ddd eee PT2389 v1.3 PT2389 Min. 0.053 0.004 0.049 0.008 0.008 0.006 0.006 Nom. Max. 0.069 0.010 0.065 0.012 0.010 0.011 0.010 0.008 0.009 0.341 BSC 0.236 BSC 0.154 BSC 0.025 BAS 0.016 0.050 0.041 REF 0.010 BAS 0.003 0.003 0 8 5 15 0 0.004 0.008 0.004 0.007 0.004 - 22 - September, 2004 Tel: 886-2-66296288 Fax: 886-2-29174598 URL: http://www.princeton.com.tw 5-Mode Preset Equalizer IC with Bass Booster & 3D Effect PT2389 Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. Dimensioning and tolerancing per ANSI Y14.5M-1982. Dimensions in inches (angles in degrees) Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.006" per end. Dimension E1 does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed "0.006" per side. D1 and E1 dimensions are determined at dutum H. The package top may be smaller than the package bottom. Dimensions D and E1 are determined at the outermost extremes of the plastic body exclusive of mold flash, tie bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic. Datums A and B to be determined at datum H. N is the maximum number of terminal position. (N=24) The dimensions apply to the flat section of the lead between 0.004 to 0.010 inches from the lead tip. Dimension b does not include dambar protrusion. Allowable dambar protrusion shall be 0.004" total in excess of b dimension at maximum material condition. The dambar can not be located on the lower radius of the foot. Refer to JEDEC MO-137 variation AE. JEDEC is the registered trademark of JEDEC SOLID STATE TECHNOLOGY ASSOCIATION PT2389 v1.3 - 23 - September, 2004