100344 100344 Low Power 8-Bit Latch with Cut-Off Drivers Literature Number: SNOS132 100344 Low Power 8-Bit Latch with Cut-Off Drivers General Description The 100344 contains eight D-type latches, individual inputs (Dn), outputs (Qn), a common enable pin (E), latch enable (LE), and output enable pin (OEN). A Q output follows its D input when both E and LE are LOW. When either E or LE (or both) are HIGH, a latch stores the last valid data present on its D input prior to E or LE going HIGH. A HIGH on OEN holds the outputs in a cut-off state. The cut-off state is designed to be more negative than a normal ECL LOW level. This allows the output emitter-followers to turn off when the termination supply is -2.0V, presenting a high impedance to the data bus. This high impedance reduces termination power and prevents loss of low state noise margin when several loads share the bus. The 100344 outputs are designed to drive a doubly terminated 50 transmission line (25 load impedance). All inputs have 50 k pull-down resistors. Features n n n n n n Cut-off drivers Drives 25 load Low power operation 2000V ESD protection Voltage compensated operating range = -4.2V to -5.7V Available to MIL-STD-883 Logic Symbol Pin Names Description D0-D7 Data Inputs E Enable Input LE Latch Enable Input OEN Output Enable Input Q0-Q7 Data Outputs DS100317-4 Connection Diagrams 24-Pin DIP 24-Pin Quad Cerpak DS100317-2 DS100317-1 (c) 1998 National Semiconductor Corporation DS100317 www.national.com 100344 Low Power 8-Bit Latch with Cut-Off Drivers August 1998 Logic Diagram DS100317-5 Truth Table Inputs Outputs Dn E LE OEN L L L L L H L L L H X H X L Latched (Note 1) X X H L Latched (Note 1) X X X H Cutoff Qn H = HIGH Voltage level L = LOW Voltage level Cutoff = lower-than-LOW state X = Don't Care Note 1: Retains data present before either LE or E go HIGH. www.national.com 2 Absolute Maximum Ratings (Note 2) 2000V ESD (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Recommended Operating Conditions Above which the useful life may be impaired Storage Temperature (TSTG) Maximum Junction Temperature (TJ) Ceramic VEE Pin Potential to Ground Pin Input Voltage (DC) Output Current (DC Output HIGH) Case Temperature (TC) Military Supply Voltage (VEE) -65C to +150C +175C -7.0V to +0.5V VEE to +0.5V -100 mA -55C to +125C -5.7V to -4.2V Note 2: Absolute maximum ratings are those values beyond which the device may be damaged or have its useful life impaired. Functional operation under these conditions is not implied. Note 3: ESD testing conforms to MIL-STD-883, Method 3015. Military Version DC Electrical Characteristics VEE = -4.2V to -5.7V, VCC = VCCA = GND, TC = -55C to +125C Symbol VOH Parameter Output HIGH Voltage Conditions Min Max Units TC -1025 -870 mV 0C to -1085 -870 mV -55C VIN = VIH (Max) Loading with -1830 -1620 mV 0C to or VIL (Min) 25 to -2.0V -1830 -1555 mV -55C -1035 mV 0C to -1085 mV -55C VIN = VIH (Min) Loading with -1610 mV 0C to or VIL (Max) 25 to -2.0V -1555 mV Notes +125C VOL Output LOW Voltage (Notes 4, 5, 6) +125C VOHC Output HIGH Voltage +125C VOLC Output LOW Voltage (Notes 4, 5, 6) +125C VOLZ Cutoff LOW Voltage -55C 0C to VIN = VIH (Min) mV +125C or VIL (Max) mV -55C to -1950 -1850 VIH Input HIGH Voltage -1165 -870 -55C +125C VIL Input LOW Voltage -1830 -1475 mV -55C to +125C IIL Input LOW Current 0.50 A -55C to Input HIGH Current 240 340 IEE A A -205 -73 Guaranteed LOW Signal for All Inputs VEE = -4.2V mA (Notes 4, 5, 6, 7) (Notes 4, 5, 6, 7) (Notes 4, 5, 6, 7) 0C to +125C VIN = VIH (Max) (Notes 4, 5, 6) Inputs Open VEE = -4.2V to -4.8V VEE = -4.2V to -5.7V (Notes 4, 5, 6) -55C to -73 for All Inputs -55C Power Supply Current -195 Guaranteed HIGH Signal (Notes 4, 5, 6) VIN = VIL (Min) VEE = -5.7V +125C IIH OEN = HIGH +125C Note 4: F100K 300 Series cold temperature testing is performed by temperature soaking (to guarantee junction temperature equals -55C), then testing immediately without allowing for the junction temperature to stabilize due to heat dissipation after power-up. This provides "cold start" specs which can be considered a worst case condition at cold temperatures. Note 5: Screen tested 100% on each device at -55C, +25C, and +125C, Subgroups 1, 2, 3, 7, and 8. Note 6: Sample tested (Method 5005, Table I) on each manufactured lot at -55C, +25C, and +125C, Subgroups A1, 2, 3, 7, and 8. Note 7: Guaranteed by applying specified input condition and testing VOH/VOL. 3 www.national.com AC Electrical Characteristics VEE = -4.2V to -5.7V, VCC = VCCA = GND Symbol Parameter tPLH Propagation Delay tPHL Dn to Output tPLH Propagation Delay tPHL LE, E to Output TC = -55C TC = +25C TC = +125C Min Max Min Max Min Max 0.50 2.60 0.70 2.60 0.70 3.10 ns Figures 1, 2 (Notes 8, 9, 10, 12) 0.80 3.30 1.00 3.30 1.10 3.80 ns Figures 1, 4 (Notes 8, 9, 10, 12) ns Figures 1, 2 (Notes 8, 9, 10, 12) ns Figures 1, 3 tPZH Propagation Delay 1.00 4.60 1.10 4.20 1.20 4.40 tPHZ OEN to Output 0.70 3.00 0.70 2.80 0.70 3.20 0.40 2.50 0.40 2.40 0.40 2.70 tTLH Transition Time tTHL 20% to 80%, 80% to 20% ts Setup Time th Units Conditions (Note 11) D0-D7 1.50 1.50 1.70 ns Figures 1, 3 D0-D7 0.60 0.60 0.60 ns Figures 1, 3 LE, E 2.40 2.40 2.40 ns Figures 1, 3 Hold Time tpw(H) Notes Pulse Width HIGH (Note 11) (Note 11) (Note 11) Note 8: F100K 300 Series cold temperature testing is performed by temperature soaking (to guarantee junction temperature equals -55C), then testing immediately after power-up. This provides "cold start" specs which can be considered a worst case condition at cold temperatures. Note 9: Screen tested 100% on each device at +25C temperature only, Subgroup A9. Note 10: Sample tested (Method 5005, Table I) on each manufactured lot at +25C, Subgroup A9, and at +125C and -55C temperatures, Subgroups A10 and A11. Note 11: Not tested at +25C, +125C, and -55C temperature (design characterization data). Note 12: The propagation delay specified is for single output switching. Delays may vary up to 300 ps with multiple outputs switching. Test Circuitry DS100317-6 Notes: VCC, VCCA = +2V, VEE = -2.5V L1 and L2 = equal length 50 impedance lines RT = 50 terminator internal to scope Decoupling 0.1 F from GND to VCC and VEE All unused outputs are loaded with 25 to GND CL = Fixture and stray capacitance 3 pF FIGURE 1. AC Test Circuit www.national.com 4 Switching Waveforms DS100317-7 FIGURE 2. Propagation Delay and Cutoff Times DS100317-8 FIGURE 3. Setup, Hold and Pulse Width Times DS100317-9 FIGURE 4. Propagation Delay LE, E to Q 5 www.national.com 6 Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead Ceramic Dual-In-Line Package (0.400" Wide) (D) NS Package Number J24E 24-Lead Quad Cerpak (F) NS Package Number W24B 7 www.national.com 100344 Low Power 8-Bit Latch with Cut-Off Drivers LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated