2001
Rast 5 Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
2
Rast 5
Table of Contents
AMP multifitting Mark II
Introduction ……………………………………………………………………………2002
Direct and Indirect Connection 5.0mm Centerline…………………………………2003
Derating Curves ………………………………………………………………………2004
Keying Plan and Cable Exit …………………………………………………………2005
Technical Features……………………………………………………………………2006
Direct Mating Connector System ……………………………………………2007, 2008
Indirect Mating Connector System……………………………………………2009-2011
PC Board Frame………………………………………………………………………2012
AMP MONO-SHAPE
Introduction ……………………………………………………………………………2013
Connector Versions …………………………………………………………………2014
Tab Connectors ………………………………………………………………………2015
Tab Connectors Keying Plan ………………………………………………………2016
Tab Connector 3-10 Positions ………………………………………………2017-2020
Single Way Connectors ………………………………………………………………2021
Single Way Connectors Keying Plan ………………………………………………2022
PCB Connectors ………………………………………………………………2023-2027
Satellite Connectors …………………………………………………………………2028
Satellite Connectors Keying Plan……………………………………………………2029
Bridge Connectors Keying Plan ……………………………………………………2030
AMP MONO-SHAPE Mark II
Introduction ……………………………………………………………………………2031
Technical Data ………………………………………………………………………2032
Keying Plan and Cable Exit …………………………………………………………2033
Tab Connector System ………………………………………………………2034-2035
TAB-BRIDGE Connector System - Short Circuit …………………………………2036
PCB Connector System ………………………………………………………2037-2041
Application Tooling ……………………………………………………………2042-2045
Standard Timer
Introduction…………………………………………………………………………… 2046
Interior and Exterior Locking…………………………………………………………2047
Keying Plan ……………………………………………………………………………2048
Housings ………………………………………………………………………2049-2059
Connectors and Contacts ……………………………………………………………2060
2002
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
Introduction
Direct Mating Connectors
for PC Boards, 28
Positions, up to 6 A Current
Carrying Capacity
Indirect Mating Connectors,
18 Positions, up to 16 A
Current Carrying Capacity
Variable Keying
Double Wire Termination
possible
Product Features
Tyco Electronics’ newly
designed AMP multifitting
Mark II Connector System
was developed according
to the latest connector
design standards.
The requirements of
advanced In-Line mating
technology for the
components and contacts of
pc boards are incorporated
in the direct and indirect
versions of these connector
systems.
This system is suitable for a
wide wire size range.
Current carrying capacity is
16 A maximum.
Double termination is
possible with 0.5 and 0.5
mm2or 0.5 and 0.75 mm2
conductors.
The connectors are avail-
able in 1- to 8-positions
(indirect) resp. 2- to 8-
positions (direct) with an
exterior locking device.
Interior locking options are
available on request.
Supplied in chain and
provided with all keying and
polarisation ribs, the
connectors can be operated
economically with modern
Application Tooling
Equipment.
2003
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
Direct and Indirect Mating Connection, 5.0 mm Centerline
METRIC
Dimensions are
millimetres over inches
Indirect Mating Connection,
5.0 mm Centerline
1Double Wire Exit
2Wire Exit 90°
3Wire Exit 180°
4Cover
5Exterior Locking Latch
6Keying
7Polarisation
Indirect Mating Connection
with Interior Locking,
5.0 mm Centerline
1Double Wire Exit
2Wire Exit 90°
3Wire Exit 180°
4Cover
5Interior Locking Latch
6Keying
7Polarisation
Direct Mating Connection,
5.0 mm Centerline
1Double Wire Exit
2Wire Exit 90°
3Wire Exit 180°
4Cover
5Exterior Locking Latch
6Keying
7Polarisation
6
5
1
3
2
3
3
4
4
4
6
5
7
7
1
2
7
1
2
6
5
2004
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
Derating Curves
Direct Mating Connector
System
Connector:
8 positions
Material:
Brass, tin plated
Wire:
0.5 mm2
PC Board:
FR4, 2 x 0.35 µm Copper,
tin plated
7
6
5
4
3
2
1
0
0 102030405060708090100110
t/°C
I/A
Current
Ambient Temperature
Indirect Mating Connector
System
Material:
Brass, tin plated
Wire:
0.5 mm2(Curve 1 and 2)
1.0 mm2(Curve 3)
Mating Part:
6.3 x 0.8 mm Tab,
Brass, tin plated
7
6
5
4
3
2
1
02
04
06
08
0
1
00
t/
ϒ
/
ϒ
/
C
ϒ
C
ϒ
I/
A
/
A
/
12
0
8
2
1
9
1
0
3
Ambient Temperature
Curve 1:
2 positions
Curve 2:
8 positions
Curve 3:
4 positions
Indirect Mating Connector
System
Material:
CuNi2Si, silver plated
Wire:
1.5 mm2, tin plated
Mating Part:
6.3 x 0.8 mm Tab,
Brass, tin plated
14
12
10
8
6
4
2
0
0 20406080100
t/°C
I/A
120 140
16
18
21
Ambient Temperature
Curve 1:
1 position
Curve 2:
4 positions
Current
Current
2005
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
2
Rast 5
Keying Plan and Cable Exit
Keying Plan
from Mating Direction,
Fully-Keyed Version
1Locking Latch
2Keying Rib
3Polarisation Rib
4Cavity Number
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
12
43
Keyed Version:
05-C according RAST 5
This final keying version will be
produced on the Application
Tooling Equipment.
Cable Exit with Interior Locking
Cable Exit with Interior
and Exterior Locking
Cable Exit with Exterior Locking
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
c a
d b
d
b
c
Direct Mating of a PCB
with PC Board Frames
2006
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
Technical Features
Technical Data
Centerline:
5.0 mm
Housing Material:
Polyamide, PA 6.6 and PA 6
Standard Colour:
Natural
Current Voltage:
250 V ~
Air and Creepage Distance:
>3.2 mm
Flammability Rating:
UL 94 V-2
Approvals:
VDE, UL
No. of Positions:
2- to 8-positions
Contact Material:
Brass
Contact Finish:
Tin plated
Wire Size Range:
0.35–1.0 mm2
Temperature Range:
40 °C up to +105 °C
Current Rating:
6 A max.
Insulation Diameter:
2.8 mm max.
Insulation Resistance:
>10 M
Mating Force:
7 N per contact*
Unmating Force:
1.5 N*
Product Specification:
108-18653
Application Specification:
114-18289
*)measured with polished steel
plate 1.5 mm thickness
No. of Positions:
1- to 8-positions
Contact Material:
Brass/ CuNi2Si
Contact Finish:
Tin plated/ silver plated
Wire Size Range:
0.35–1.0 mm2/1.0–1.5 mm2
Temperature Range:
40 °C up to +130 °C
Current Rating:
10 A, up to 4 contacts 16 A
Insulation Diameter:
3.0 mm max.
Insulation Resistance:
>10 M
Mating Force:
6.5 N per contact**
Unmating Force:
1.5 N**
Product Specification:
108-18652
Application Specification:
114-18288, 114-18382
**)measured with polished steel
tab 6.3 x 0.8 mm
Direct Mating Connectors Indirect Mating Connectors
2007
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
2
Rast 5
Direct Mating Connector System
– 1 –
– 2 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 4 –
– 1 –
– 2 –
– 3 –
– 4 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
RAST 5 Version Package
Quantity
Part Numbers
with Exterior Locking
PA 6.6 PA 6 *
Part Numbers
with Interior Locking
PA 6.6 PA 6 *
1-1241172-2 1-1534075-2 4,900
1-1241172-3 1-1534075-3 3,136
1-1241172-3 1-1534075-3 3,136
1-1241172-4 1-1534075-4 2,352
1-1241172-4 1-1534075-4 2,352
1-1241172-5 1-1534075-5 1,960
1-1241172-5 1-1534075-5 1,960
*
)
According to IEC 60695-2-1/1; GWT (Glow Wire Test) 750 °C without flame, see VDE M-Test Report.
The final keying version will be produced on the Application Tooling Equipment.
Technical Data Wire Size Range:
0.35–1.0 mm2
Current Carrying Capacity (max.):
6 A
2008
AMP multifitting Mark II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
Direct Mating Connector System (continued)
RAST 5 Version Package
Quantity
Part Numbers
with Exterior Locking
PA 6.6 PA 6*
Part Numbers
with Interior Locking
PA 6.6 PA 6 *
*
)
According to IEC 60695-2-1/1; GWT (Glow Wire Test) 750 °C without flame, see VDE M-Test Report.
The final keying version will be produced on the Application Tooling Equipment.
1-1241172-6 1-1534075-6 1,568
1-1241172-6 1-1534075-6 1,568
2-1241172-6 2-1534075-6 1,568
1-1241172-7 1-1534075-7 1,372
1-1241172-7 1-1534075-7 1,372
1-1241172-8 1-1534075-8 1,176
1-1241172-8 1-1534075-8 1,176
Technical Data Wire Size Range:
0.35–1.0 mm2
Current Carrying Capacity (max.):
6 A
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
2009
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP multifitting Mark II
Connectors in In-Line Mating Technology
Indirect Mating Connector System
– 1 –
– 1 –
– 2 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 4 –
– 1 –
– 2 –
– 3 –
– 4 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
1-1241170-2 1-1534072-2 4,900 1-1394355-2 1-1534077-2
1-1241170-3 1-1534072-3 3,136 1-1394355-3 1-1534077-3
1-1241170-3 1-1534072-3 3,136 1-1394355-3 1-1534077-3
1-1241170-4 1-1534072-4 2,352 1-1394355-4 1-1534077-4
1-1241170-4 1-1534072-4 2,352 1-1394355-4 1-1534077-4
1-1241170-5 1-1534072-5 1,960 1-1394355-5 1-1534077-5
1-1241170-5 1-1534072-5 1,960 1-1394355-5 1-1534077-5
1-1241170-1 1-1534072-1 9,604 -1241170-1 1-1534072-1
Technical Data Wire Size Range:
0.35–1.0 mm2
Current Carrying Capacity
(max.):
10 A
*
)
According to IEC 60695-2-1/1; GWT (Glow Wire Test) 750 °C without flame, see VDE M-Test Report.
The final keying version will be produced on the Application Tooling Equipment.
RAST 5 Version Package
Quantity
Part Numbers
with Exterior Locking
PA 6.6 PA 6 *
Part Numbers
with Interior Locking
PA 6.6 PA 6 *
METRIC
Dimensions are
millimetres over inches
2010
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP multifitting Mark II
Connectors in In-Line Mating Technology
Indirect Mating Connector System (continued)
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
1-1241170-6 1-1534072-6 1,568
2-1241170-6 2-1534072-6 1,568
1-1241170-7 1-1534072-7 1,372
1-1241170-7 1-1534072-7 1,372 1394355-7 1534077-7
1-1241170-8 1-1534072-8 1,176
1-1241170-8 1-1534072-8 1,176
1-1241170-6 1-1534072-6 1,568
Technical Data Wire Size Range:
0.35–1.0 mm2
Current Carrying Capacity
(max.):
10 A
*
)
According to IEC 60695-2-1/1; GWT (Glow Wire Test) 750 °C without flame, see VDE M-Test Report.
The final keying version will be produced on the Application Tooling Equipment.
RAST 5 Version Package
Quantity
Part Numbers
with Exterior Locking
PA 6.6 PA 6*
Part Numbers
with Interior Locking
PA 6.6 PA 6*
METRIC
Dimensions are
millimetres over inches
2011
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP multifitting Mark II
Connectors in In-Line Mating Technology
Indirect Mating Connector System (continued)
– 1 –
– 1 –
– 2 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 1 –
– 2 –
– 3 –
– 4 –
– 1 –
– 2 –
– 3 –
– 4 –
1-1241171-2 1-1534073-2 4,900 1-1394556-2 1-1534078-2
1-1241171-3 1-1534073-3 3,136 1-1394556-3 1-1534078-3
1-1241171-3 1-1534073-3 3,136 1-1394556-3 1-1534078-3
1-1241171-4 1-1534073-4 2,352 1-1394556-4 1-1534078-4
1-1241171-4 1-1534073-4 2,352 1-1394556-4 1-1534078-4
1-1241171-1 1-1534073-1 9,604 1--1241171-1 1-1534073-1
Technical Data Wire Size Range:
1.0–1.5 mm2
Current Carrying Capacity (max.):
16 A
*
)
According to IEC 60695-2-1/1; GWT (Glow Wire Test) 750 °C without flame, see VDE M-Test Report.
The final keying version will be produced on the Application Tooling Equipment.
RAST 5 Version Package
Quantity
Part Numbers
with Exterior Locking
PA 6.6 PA 6 *
Part Numbers
with Interior Locking
PA 6.6 PA 6 *
METRIC
Dimensions are
millimetres over inches
2012
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP multifitting Mark II
Connectors in In-Line Mating Technology
PC Board Frame
2 5 10.1 1c, 2d 1/2 2-964577-2 2,200
1c, 2d, 3c 1/2, 3/4 2b 1-964577-4
4 15 20.1 1c, 3c, 4d 1/2, 3/4 4b 2-964577-4 1,700
1c, 3c, 4d 1/2, 3/4 1b, 4a 3-964577-4
5 20 25.1 3d 1/2, 4/5 1-964577-5 1,500
6 25 30.1 4d 1/2, 5/6 6b 1-964577-6 1,500
4d 1/2, 5/6 1b, 6a 2-964577-6
7 30 35.1 2c, 3d, 7c 2/3, 5/6 1b, 2b 4/5 1-964577-7 1,200
2c, 3d, 7c 2/3, 5/6 2b, 7a 4/5 2-964577-7
8 35 40.1 2c, 3d, 7c 2/3, 7/8 2a 4/5 1-964577-8 1,000
2c, 3d, 7c 2/3, 7/8 2b, 4b 4/5 2-964577-8
12255 60.1 1c, 2d, 3c, 4d, 1/2, 3/4, 5/6, 2b, 3a, 4a, 6a, 4/5, 8/9 1-964578-2 1.500
5c, 8c, 10d, 12d 8/9, 9/10, 11/12 7a, 7b, 8a, 8b
Preferred Parts are printed bold
No. of
Positions Keying Latching Polarisation Additional
Board
Lock
Package
Quantity
Dimensions
(mm)
AB
Part Number
PC Board Frame,
PA 6.6, Black
B
A
Latching Hole
Keying
PC Board Frame
PC Board
METRIC
Dimensions are
millimetres over inches
Rast 5
2
2013
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Introduction
METRIC
Dimensions are
millimetres over inches
AMP MONO-SHAPE
Connectors in In-Line
Mating Technology
AMP MONO-SHAPE connectors
represent a valid solution to the
ever-increasing requirements
for production and application
flexibility.They are high
productivity, great flexibility,
quality, minimum applied cost.
AMP MONO-SHAPE product-
line includes a full range of 5.0
mm pitch modular connectors
contents with similar outer
shape, several variation in the
mating area such as PC Board
and 6.3 x 0.8 mm tabs (RAST
5), plus a version for harness
shunts.
AMP MONO-SHAPE connection
system adopts the IDC
termination technology,which
improves application results
and quality level.
The AMP MONO-SHAPE
product range,combined with
the performances and
properties offered by the
termination system,allow to
manufacture extremely
complicated harness structures
while still maintaining high
production levels.
IDC Connector system
design to maximise the
full integration with the
application tooling assuring
total flexibility in harness
design.
High current system, up
to16 Ampere, designed to
satisfy several appliance
requirements.
ID Contact designed to
accept standard discrete
wires ranging from 0.5 up to
1.5 mm2,according to the
connector configuration.
The connector incorporates
modern in-line mating
technology on a 5.0 mm
centerline with no loss of
spacing and a variety of
keying possibilities.
Wiring faults eliminated
through high automation.
Approvals:
VDE: 4751-1431-4024 / A
10A and
4751-1431-4024 / A 9E
UL E 28476 Vol. 9 Sec. 7;
97 ME 17936; AP-27HB
Technical Features
2014
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE Connector Versions
METRIC
Dimensions are
millimetres over inches
Single Way Connectors
Single Way connectors with
insulation displacement
contacts for use on tinned
copper alloy tab 6.3 x 0.8 mm
according to DIN 46244.
Satellite Connectors
3 position connectors, pitch
5.0 mm, with short circuited
insulation displacement
contacts for harness shunts.
Wire Size Range:
0.5–1.5 mm2
Current Rating:
16 Ampère max. acc. to wire size
TAB Connectors
2–12 position 5.0 mm pitch
connectors with insulation
displacement contacts mateable
with components according to
RAST 5 and with tinned copper
alloy tab 6.3 x 0.8 mm
according to DIN 46244.
Same Shape -
Different Applications
With the same outside shape
four connector versions are
available, which are to handle
with the same application
tooling.
Wire Size Range:
0.5–1.5 mm2
Current Rating:
16 Ampere max. acc. to wire size
-For LIF version up to
10 Ampere max
Wire Size Range:
0.5–1.5 mm2
Current Rating:
16 Ampere max. acc. to wire size
Supply Status:
In order to increase product-
ivity these items are supplied
in sticks.
Wire Size Range:
0.5–0.75 mm2
Current Rating:
6 Ampere max. acc. to wire size
PC Board:
Single or both sides printed 5
µm tin over 35 µm copper
PCB Connectors
2–12 position 5.0 mm pitch
connectors with insulation
displacement contacts accor-
ding to printed circuit boards
with thickness 1.5±0.2 mm and
5.0 mm pitch.
LIF version 2
point contact
instead of 4 as
per standard
version
2015
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
TAB Connector
METRIC
Dimensions are
millimetres over inches
2
Rast 5
1
3
4
5
2
6
Centerline:
5.0 mm, according to RAST 5
specifications
Configurations:
2- to 12-positions
Housing Material:
Plastic PA 6.6
Housing Colour:
Natural colour for standard
version
Grey colour for LIF version
Contact Material:
Copper alloy, post-tinned
2.0 µm min.
Polarisation, Keying,
Locking Latches:
according to RAST 5
specifications
(see customer drawings)
Track Resistance:
as per IEC 112 (250 V)
Glow Wire Test:
as per IEC 695-2-1 (850 °C)
and 750°C no flame
Air and Creepage Distance:
according to EN 60998-1
(IEC 998-1)
for 380 V, 4.0 mm
Voltage Resistance:
according to EN 60998-1
(IEC 998-1)
1750 V for 4 minutes
Insulation Resistance:
according to EN 60998-1
(IEC 998-1)
>5 M
Wire Size Range:
from 0.5 to 1.5 mm2
Current Rating:
Standard Version
16 A max. according to wire
size
0.5 mm23 A, 0.75 mm26 A,
1.0 mm210 A, 1.5 mm216 A
LIF Version
10 A max. according to wire
size
0.5 mm23 A, 0.75 mm26 A,
1.0 mm210 A, 1.5 mm210 A
Rated Voltage:
380 Volts max.
Wire Type:
H05V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for 0.5–1.0 mm2wires with
copper or tinned stranded wires
H07V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for wires from 1.5 mm2with
copper or tinned stranded wires
Insulation Type:
PVC suitable for temperatures
up to 70 °C / 105 °C
Insulation Diameter Range:
2.0–3.5 mm
Temperature Range:
–25 °C up to +105 °C
Wire Extraction Force/Way:
50 N min. on wire size 0.5 mm2
Application Specification:
114-20016
Product Specification:
Standard version: 108-20065
LIF version: 108-20215
Homologations:
acc.to VDE File No. 3905
(to 16 A) and UL File No.
E28476 (to 14 A)
Technical Features
AMP MONO-SHAPE
TAB Connector
1Cover closed after Wire
Insertion. Wire Direction
90°. 180° when locked in
Cover Recess
2Cavity Numbers
3Polarisation
similar to the Keying
(Located on the Back Side)
4Keying
5Interior Locking Latch
6Colour Marking
Black
02-Q
Black
02-A
02-O
Blue
02-L
02-P
Red
02-C
Black
02-B
02-E
02-F
Grey
2016
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Keying Plan
METRIC
Dimensions are
millimetres over inches
Keying Plan
from Mating Direction,
1Locking Latch
2Slanted Keying Rib
3Keying Rib
4Polarisation Rib
5Cavity Number
AMP MONO-SHAPE
TAB Connector
2 Position RAST 5 Variations
(Variable Keying)*
a
– 1 –
– 2 –
c
– 3 –
– 4 –
d
– 5 –
– 6 –
b
c
– 7 –
54
123
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282002-2 2-282002-2 3-282002-2 6.500 3.500 28.500
1-284338-2 2-284338-2
1-282002-1 2-282002-1 2-282002-1 6.500 3.500 28.500
1-284338-1 2-284338-1
1-282002-3 2-282002-3 6.500 3.500 28.500
1-284338-3 2-284338-3 3-284338-3
1-282002-4 2-282002-4 6.500 3.500
1-284338-4
1-282002-5 2-282002-5 6.500 3.500
1-282002-6 2-282002-6 6.500 3.500
1-282002-7 2-282002-7 3-282002-7 6.500 3.500 28.500
1-284338-7
ca
– 1 –
– 2 –bd
c– 1 –
a
– 2 –
d
c– 1 –
– 2 –
db
* Final keying version is produced on the Application Tooling Machines.
Bold Part Numbers are LIF Version
Black
03-B
Black
Violet
2017
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE TAB Connector
METRIC
Dimensions are
millimetres over inches
2
Rast 5
3 Position RAST 5 Variations
(Variable Keying)*
03-B
03-K
Grey
03-B
03-K
Red
03-D
03-F
Green
03-B
03-K
Blue
03-A
03-I
Orange
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282003-1 2-282003-1 3-282003-1 4.160 2.500 24.000
1-284339-1 2-284339-1
1-282003-2 2-282003-2 3-282003-2 4.160 2.500 24.000
1-284339-2 2-284339-2
1-282003-3 2-282003-3 4.160 2.500
1-284339-3 2-284339-3
282233-2 282233-2 4.160 2.500
1-282003-4 2-282003-4 4.160 2.500
1-284339-4 2-284339-4
1-282003-5 2-282003-5 4.160 2.500
1-284339-5 2-284339-5
1-282003-6 2-282003-6 4.160 2.500
c
b
– 1 –
d– 2 –
c
d– 3 –
c
d– 1 –
c
b
– 2 –
db
– 3 –
ca
– 1 –
d– 2 –
c
db
– 3 –
ca
– 1 –
– 2 –
c
d– 3 –
c
d– 1 –
c
b
– 2 –
db
– 3 –
c
d– 1 –
c
b
– 2 –
db
– 3 –
1-282003-7 4.160
c
d– 1 –
c
b
– 2 –
db
– 3 –
1-284396-1 4.160
* Final keying version is produced on the Application Tooling Machines.
Bold Part Numbers are LIF Version
2018
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE TAB Connector
METRIC
Dimensions are
millimetres over inches
4 Position RAST 5 Variations
(Variable Keying)*
5 Position RAST 5 Variations
(Variable Keying)*
* Final keying version is produced on the Application Tooling Machines.
04-A
Red
04-D
Black
04-A
Grey
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282004-1 2-282004-1 3-282004-1 2.120 2.000 18.750
1-282004-2 2-282004-2 3-282004-2 2.120 2.000 18.750
1-282004-3 2-282004-3 2.120 2.000
c
b
– 1 –
d– 2 –
c– 3 –
d– 4 –
c
d– 1 –
c– 2 –
db
– 3 –
c
d– 4 –
c
b
– 1 –
d– 2 –
c– 3 –
d– 4 –
Red
Red
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282005-1 2-282005-1 2.600 1.500 18.750
1-284545-1 2.600 1.500 18.750
c– 1 –
d
c– 2 –
– 3 –
d
c– 4 –
d
c– 5 –
d
b
2019
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
2
Rast 5
AMP MONO-SHAPE TAB Connector
6 Position RAST 5 Variations
(Variable Keying)*
Red
Violet
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282006-1 2-282006-2 3-282006-2 2.080 1.200 13.500
1-282006-3 2-282006-3 3-282006-3 2.080 1.200 13.500
1-284745-1 2.080
7 Position RAST 5 Variations
(Variable Keying)*
Black
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282007-1 2-282007-1 1.820 1.200
1-284397-1 1.820 1.200
c
– 1 –
b
– 2 –
d
c
– 3 –
d
c
– 4 –
d
c
– 5 –
b
– 6 –
d
c
– 7 –
d
2020
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE TAB Connector
METRIC
Dimensions are
millimetres over inches
RAST 5 Version
* Final keying version is produced on the Application Tooling Machines.
Bold Part Numbers are LIF Version
* Final keying version is produced on the Application Tooling Machines.
Bold Part Numbers are LIF Version
8 Position RAST 5 Variations
(Variable Keying)*
Violet
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
284085-1 2-284085-1 1.560 900
1-284685-1 2-284685-1
284085-2 2-284085-2 1.560 900
c
– 1 –
d
c
– 2 –
db
c
– 3 –
d
c
– 4 –
db
c
– 5 –
d
ca
– 6 –
db
c
– 7 –
d
c
– 8 –
d
RAST 5 Version
10 Position RAST 5 Variations
(Variable Keying)*
Suitable for RAST 5
Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282010-1 2-282010-1 1.300 700
1-284686-1 2-284686-1
c
– 1 –
d
c
– 2 –
d
c
– 3 –
d
c
– 4 –
– 5 –
d
c
– 6 –
db
c
– 7 –
d
ca
– 8 –
– 9 –
d
c
–10
d
2021
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE Single Way Connector
2
3
4
1
5
Single Way Connector
1All Single Way Connectors
are supplied in “stick-form”
by 6 single ways each.
They will be cut from the
Application Tooling Machines
2Cover closed after Wire
Insertion. Wire Direction 90°.
180° when locked in Cover
Recess
3Polarisation similar to the
keying of the front side
4Keying
5Plastic Noses which Lock
into the TAB Hole
6Colour Marking
Centerline:
5.0 mm, according to RAST
5 specifications
Configurations:
1 position
Housing Material:
Plastic PA 6.6
Housing Colour:
Natural colour
Contact Material:
Copper alloy, post-tinned
2.0 µm min.
Polarisation, Keying,
Locking Latches:
according to RAST 5
specifications
(see customer drawings)
Track Resistance:
as per IEC 112 (250 V)
Glow Wire Test:
as per IEC 695-2-1 (850 °C)
and 750°C no flame
Air and Creepage Distance:
according to EN 60998-1
(IEC 998-1)
for 380 V, 4.0 mm
Voltage Resistance:
according to EN 60998-1
(IEC 998-1)
1750 V for 4
minutes
Insulation Resistance:
according to EN 60998-1
(IEC 998-1)
>5 M
Wire Size Range:
from 0.5 to 1.5 mm2
Current Rating:
16 A max. according to wire
size
0.5 mm23 A, 0.75 mm26 A,
1.0 mm210 A, 1.5 mm216 A
Rated Voltage:
380 Volts max.
Wire Type:
H05V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for 0.5–1.0 mm2wires with
copper or tinned stranded wires
H07V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for wires from 1.5mm2with
copper or tinned stranded wires
Insulation Type:
PVC suitable for temperatures
up to 70 °C / 105 °C
Insulation Diameter Range:
2.0–3.5 mm
Temperature Range:
–25 °C up to +105 °C
Wire Extraction Force/Way:
50 N min. on wire size 0.5 mm2
Application Specification:
114-20017
Product Specification:
108-20066
Homologations:
acc.to VDE File No. 3905
(to 16 A) and UL File No.
E28476 (to 14 A)
Counter Part:
Tab 6.3 x 0.8 mm
as per DIN 46244 norms
Materials:
Copper alloy
Finishing:
Tinned (6.0 µm max.)
Technical Features
METRIC
Dimensions are
millimetres over inches
2022
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
ca
– 1 –
d
2
1
3
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
Keying Plan from Mating Direction
Keying Plan
1Keying Rib
2Polarisation Rib
3Cavity Number
AMP MONO-SHAPE
Single Way Connector
1 Position
(Variable Keying)*
METRIC
Dimensions are
millimetres over inches
Black
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray On Reel
Packaging
Unit
On Tray On Reel
1-282086-1 1.024 10.500
1-282086-2 1.024
c– 1 –
d
ca
– 1 –
d
Orange 1-282086-3 1.024
c– 1 –
db
Green 1-282086-4 1.024
Blue 1-282086-5 1.024
Violet 1-282086-6 1.024
2023
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
1
5
43
2
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE PCB (Printed Circuit Board) Connector
PCB Connector
1Cover closed after
Wire Insertion.
Wire Direction 90°.
180° when locked in
Cover Recess
2Cavity Numbers
3Keying Slot in PC Board
4Locking Hole in PC Board
5Colour Marking
Centerline:
5.0 mm
Configurations:
2-12 positions
Housing Material:
Plastic PA 6.6
Housing Colour:
Natural colour
Contact Material:
Copper alloy, post-tinned
2.0 µm min.
Polarisation, Keying,
Locking Latches:
according to RAST 5
specifications
(see customer drawings)
Track Resistance:
as per IEC 112 (250 V)
Glow Wire Test:
as per IEC 695-2-1 (850 °C)
and 750°C no flame
Air and Creepage Distance:
according to EN 60998-1
(IEC 998-1)
for 240 V, 3.0 mm
Voltage Resistance:
according to EN 60998-1
(IEC 998-1)
1750 V for 4
minutes
Insulation Resistance:
according to EN 60998-1
(IEC 998-1)
>5 M
Wire Size Range:
from 0.5 to 0.75 mm2
Current Rating:
6 A max. according to wire size
0.5 mm23 A, 0.75 mm26 A
Rated Voltage:
220 Volts max.
Wire Type:
H05V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for 0.5–1.0 mm2wires with
copper or tinned stranded wires
H07V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for wires from 1.5mm2with
copper or tinned stranded wires
Insulation Type:
PVC suitable for temperatures
up to 70 °C / 105 °C
Insulation Diameter Range:
2.0–2.8 mm
Temperature Range:
–25 °C up to +105 °C
Wire Extraction Force/Way:
50 N min. on wire size 0.5 mm2
Application Specification:
114-20025
Product Specification:
108-20067
Homologations:
acc.to VDE File No. 3905
(to 6 A) and UL File No. E28476
(to 6 A)
Printed Circuit Board:
Thickness 1.5±0.2mm
Tinned Circuit Paths:
5.0mm pitch and width of
1.8mm
Technical Features
METRIC
Dimensions are
millimetres over inches
2024
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE PCB (Printed Circuit Board) Connector
15,0
14,0
23,0
5,0
1
12
3
4
41
2
3
Wire Exit
PCB Connector
1PC Board
2First Circuit Path
3MONO-SHAPE Connector
4Wire
Notes Concerning the PC
Board Layout
1First circuit path
2Slot for keying rib in front
of first cavity (according to
the connector 4.0 mm or
7.4 mm)
3Bore hole for locking clip
symmetric between two
cavities (diameter 2.5 mm)
4Slot for keying rib
symmetric between
two cavities
PC Board Layout
Dimensions on request.
See Customer Drawing 282042
METRIC
Dimensions are
millimetres over inches
3
Blue
4
2
Blue
2
Green
2
Brown
2
Red
2
Black
3
3
Black
3
3
Black
2025
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE PCB (Printed Circuit Board) Connector
Centerline 5.0 mm
METRIC
Dimensions are
millimetres over inches
PC Board Cut-Out
No. of Positions
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282042-1 2-282042-1 5.980 3.500
1-282042-2 2-282042-2 3-282042-2 5.980 3.500 28.500
1-282042-3 2-282042-3 3-282042-3 5.980 3.500 28.500
1-282042-4 2-282042-4 5.980 3.500
1-282042-5 2-282042-5 3-282042-5 5.980 3.500 28.500
1-282043-2 2-282043-2 3-282043-2 4.160 2.500 24.000
1-282043-3 2-282043-3 4.160 2.500
282235-2 2-282235-2 4.160 2.500
282235-3 2-282235-3 4.160 2.500
1-1284546-1 4.160
1-282044-1 2-282044-1 3-282044-1 3.120 2.000 18.750
2026
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE PCB (Printed Circuit Board) Connector
METRIC
Dimensions are
millimetres over inches
9
10
5
5
Green
5
5
6
6
7
8
8
Centerline 5.0 mm (continued)
PC Board Cut-Out
No. of Positions
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282045-1 2-282045-1 3-282045-1 2.600 1.500 18.750
1-282045-2 2-282045-2 3-282045-2 2.600 1.500 18.750
1-282045-3 2-282045-3 3-282045-3 2.600 1.500 18.750
1-284733-1 2-284733-1 3-284733-1 2.600 1.500 18.750
1-282046-1 2-282046-1 3-282046-1 2.080 1.200 13.500
1-284734-1 2-284734-1 3-284734-1 2.080 1.200 13.500
1-282047-1 2-282047-1 3-282047-1 1.820 1.200 13.500
284208-1 2-284208-1 1.560 900
284574-1 1.560
1-282049-1 2-282049-1 3-282049-1 1.300 700 10.500
1-282050-1 2-282050-1 3-282050-1 1.300 700 10.500
2027
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE PCB (Printed Circuit Board) Connector
METRIC
Dimensions are
millimetres over inches
2
Rast 5
11
10
10
Black
12
Centerline 5.0 mm (continued)
PC Board Cut-Out
No. of Positions
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-284401-1 1.300
284575-1 1.300
1-282051-1 2-282051-1 3-282051-1 1.040 700 10.500
1-282052-1 2-282052-1 3-282052-1 1.040 700 10.500
2028
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
1
2
3
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
AMP MONO-SHAPE Satellite Connector
Satellite Connector
1Cover closed after Wire
Insertion. Wire Direction 90°.
180° when locked in Cover
Recess
2Bridge between Contacts
to have Short Circuit
3Cavity Numbers
4For Satellite version, the
cavity 1 only accept TAB
contact, other cavities are
clogged
Centerline:
5.0 mm, according to RAST 5
specifications
Configurations:
3 positions only (for special
version please contact Tyco
Electronics)
Housing Material:
Plastic PA 6.6
Housing Colour:
Natural colour
Contact Material:
Copper alloy, post-tinned
2.0 µm min.
Polarisation, Keying,
Locking Latches:
according to RAST 5
specifications
(see customer drawings)
Track Resistance:
as per IEC 112 (250 V)
Glow Wire Test:
as per IEC 695-2-1 (850 °C)
and 750°C no flame
Air and Creepage Distance:
according to EN 60998-1
(IEC 998-1)
for 380 V, 4.0 mm
Voltage Resistance:
according to EN 60998-1
(IEC 998-1)
1750 V for 4
minutes
Insulation Resistance:
according to EN 60998-1
(IEC 998-1)
>5 M
Wire Size Range:
from 0.5 to 1.5 mm2
Current Rating:
16 A max. according to
wire size
0.5 mm23 A, 0.75 mm26 A,
1.0 mm210 A, 1.5 mm216 A
Rated Voltage:
380 Volts max.
Wire Type:
H05V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for 0.5–1.0 mm2wires with
copper or tinned stranded wires
H07V-K (70 °C max.)
or FR 3/2 (105 °C max.)
for wires from 1.5mm2with
copper or tinned stranded wires
Insulation Type:
PVC suitable for temperatures
up to 70 °C / 105 °C
Insulation Diameter Range:
2.0–3.5 mm
Temperature Range:
–25 °C up to +105 °C
Wire Extraction Force/Way:
50 N min. on wire size 0.5 mm2
Application Specification:
114-20026
Product Specification:
108-20070
Homologations:
acc.to VDE File No. 3905
(to 16 A) and UL File No.
E28476 (to 14 A)
Technical Features
METRIC
Dimensions are
millimetres over inches
4
2029
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
a
– 1 –
– 2 –
c
– 3 –
– 4 –
– 5 –
– 6 –
b
c
– 7 –
43
12
AMP MONO-SHAPE
Connectors in In-Line Mating Technology
Keying Plan from Mating Direction
Keying Plan
1Locking Latch
2Keying Rib
3Polarisation Rib
4Cavity Number
AMP MONO-SHAPE - 3 Position Satellite Connector
(Variable Keying)*
* Final keying version is produced on the Application Tooling Machines.
METRIC
Dimensions are
millimetres over inches
03-A
03-I
Black
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-282099-1 4.160
c
b
– 1 –
d– 2 –
c
d– 3 –
AMP MONO-SHAPE - 2 Position Satellite Connector
(Variable Keying)* Bridge between Contacts. Cavity Numbers 1-2 to have Short Circuit
02-L
02-P
02-L
02-P
Orange
02-L
02-P
Blue
02-L
02-P
Green
02-L
02-P
Violet
02-L
02-P
Black
02-C
1-284288-1 284288-1 6.500
284288-2 3.000
1-284288-3 284288-3 6.500 3.000
284288-4 3.000
284288-5 3.000
1-284288-6 284288-6 6.500 3.000
284288-7 3.000
c– 1 –
– 2 –
db
c– 1 –
– 2 –
db
c– 1 –
– 2 –
db
c– 1 –
– 2 –
db
c– 1 –
– 2 –
db
c– 1 –
– 2 –
db
c– 1 –
a
– 2 –
d
2030
AMP MONO-SHAPE
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Keying Plan from Mating Direction
METRIC
Dimensions are
millimetres over inches
* Final keying version is produced on the Application Tooling Machines.
AMP MONO-SHAPE Bridge Connector - 3 Position RAST 5 Variation
(Variable Keying)* Bridge between Contacts. Cavity Numbers 1-2-3 to have Short Circuit
03-A
03-I
Green
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
284289-1 2.500
c
b
– 1 –
d– 2 –
c
d– 3 –
AMP MONO-SHAPE Bridge Connector - 6 Position RAST 5 Variation
(Variable Keying)* Bridge between Contacts. Cavity Numbers 1-2-3 to have Short Circuit
Green
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
284290-1 1.200
AMP MONO-SHAPE Bridge Connector - 6 Position RAST 5 Variation
(Variable Keying)* Bridge between Contacts. Cavity Numbers 1-2 and 3-4 to have Short Circuit
Black
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
284290-2 1.200
AMP MONO-SHAPE Bridge Connector - 6 Position RAST 5 Variation
(Variable Keying)* Bridge between Contacts. Cavity Numbers 1-2-3-4-5-6 to have Short Circuit
RAST 5 Version
Suitable for RAST 5 Version
Colour Marking
Part
Numbers
On Tray Loose Piece On Reel
Packaging
Unit
On Reel Loose Piece On Reel
1-284744-1 2.080
Rast 5
2
2031
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Introduction
METRIC
Dimensions are
millimetres over inches
AMP MONO-SHAPE
MARK II Connectors in
In-Line Mating Technology
MONO-SHAPE Mark II
Connector System was
developed according to the
newest level of knowledge and
standard.
The requirements of advanced
In-Line mating technology for
the component and contact of
printed circuit board (PCB) is
granted by the two versions
TAB and PCB connector
systems.
System is designed to
maximise the full integration
with the application tooling,
assuring the flexibility in the
harness design.
This system is suitable for a
wide wire size range of
conductor and current carrying
capacity up to 16 A.
Double termination is possible
with 0.5 and 0.5mm2or 0.5 and
0.75mm2conductors.
(See application spec.
114-20104 for details)
The connectors are available in
1 to 10 positions (TAB Version)
with interior locking device and
2 to 12 positions (PCB Version)
Connectors are supplied in
chain and provided with all
keying and polarisation ribs the
connectors can be handled
automatically with a modern
Application Tooling Equipment.
Wiring faults checked and
eliminated through high
automation.
Application Machines shall
provide to print a colour code
mark on the connectors cover
after wire termination, feasible
on all connectors configuration,
for connector identification on
harnesses.
Housing moulded in different
materials for different
applications
Standard, Part Numbers with
pre-dash 0 (as 0-284471-1)
Housing in unfilled PA 6/6,
UL 94V-2
For UL94V0, Part Numbers
with pre-dash 1
(as 1-284471-1)
Housing in unfilled PA 6/6,
UL 94V-0
High Operating Temperature
(up to 130°), Part Numbers
with pre-dash 2 (as 2-
284471-1) Unfilled PA 4/6,
UL 94V-2 (available for TAB
Version only)
Glow Wire 750° no flame,
Part Numbers with pre-dash
3 (as 3-284471-1) Housing
in unfilled PA 6, UL 94V-2
Technical Features
TAB-BRIDGE Connectors
Same design as TAB
Connectors but with a bridge
between two adjacent contacts
to have a Short Circuit between
them.
Wire Size Range:
0.35–1.5 mm2
Current Rating:
16 Ampere max. acc. to
wire size used
Centerline:
5.0mm
Housing Material:
Polyamide, PA 6.6 and PA 6
Approvals:
VDE, UL CSA applied
Standard Colour:
Natural
2032
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Technical Data
METRIC
Dimensions are
millimetres over inches
TAB Connectors
1-10 position 5.0 pitch
connectors with insulation
displacement contacts mateable
with components according to
rast 5 and with tinned copper
alloy tab contacts 6.3 x 0.8mm
according to DIN 46244 and
DIN 17670 Part 1.
Current Voltage:
250 V~
Air and Creepage Distance:
>3.2mm
Flammability Rating:
According UL 94 V-2
Wire Size Range:
0.35–0.75 mm2
Current Rating:
6 Ampere max. acc. to
wire size used
PC Board:
Single or double side, with
thickness 1.6±0.2mm, FR4, 2 x
0.35 µm Copper 5µm tinned
tracks, 5.0mm pitch
PCB Connectors
2–12 position 5.0 mm pitch
connectors with insulation
displacement contacts mateable
with printed circuit boards
(PCB)
2033
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Keying Plan and Cable Exit
METRIC
Dimensions are
millimetres over inches
2
Rast 5
Keying Plan
from Mating Direction,
Fully Keyed Version
1Locking Latch
2Keying Rib
3Polarisation Rib
4Cavity Number
5Motor Mount
Special Keying
Cable Exit
1Double Wire Exit
2Wire Exit 90°
3Wire Exit 180°
4Cover
5Interior Locking Latch
(for TAB Version only)
6Keying
7Polarisation
8Motor Mount
Special Keying
9Colour Marking Area to
identify connectors after
harnesses are built up
Example of
Keyed Version:
05-C
This final keying version
will be produced on the
Application Tooling
Equipment
4
1
3
2
5
4
21
39
5
67
8
7
2034
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
TAB Connector System
METRIC
Dimensions are
millimetres over inches
AMP MONO-SHAPE MARK II
TAB Connector System
No. of Positions:
1 to 10 positions
Contact Material:
CuNi2Si
Contact Finish:
Tin Plated
Current Rating:
16 A, up to 4 contacts 16 A
Insulation Diameter:
3.0mm max.
Insulation Resistance:
>10 M
Wire Size Range:
0.35-1.5mm
2
Temperature Range:
-40°C up to +130°C
Product Specification:
108-20213
Application Specification:
114-20104
6
Violet
6
5
4
Blue
4
3
Blue
3
2
1
No. of Positions
Colour Marking
as Shipped
Part Numbers
High Glow Wire Packaging
Standard UL94V0 Temperature 750° no flame Unit
0-284471-1 1-284471-1 2-284471-1 3-284471-1 11000
0-284472-1 1-284472-1 2-284472-1 3-284472-1 5500
0-284473-1 1-284473-1 2-284473-1 3-284473-1 3520
0-284473-2 1-284473-2 2-284473-2 3-284473-2 3520
0-284474-1 1-284474-1 2-284474-1 3-284474-1 2640
0-284474-2 1-28444-2 2-284474-2 3-284474-2 2640
0-284475-1 1-284475-1 2-284475-1 3-284475-1 2200
0-284476-1 1-284476-1 2-284476-1 3-284476-1 1760
0-284476-4 1-284476-4 2-284476-4 3-284476-4 1760
0-284477-1 1-284477-1 2-284477-1 3-284477-1 1540
RAST 5 Version
2035
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
TAB Connector System (continued)
METRIC
Dimensions are
millimetres over inches
2
Rast 5
AMP MONO-SHAPE MARK II
TAB Connector System
10
8
Blue
8
7
Red
7
Blue
RAST 5 Version
No. of Positions
Colour Marking
as Shipped
Part Numbers
High Glow Wire Packaging
Standard UL94V0 Temperature 750° no flame Unit
0-284477-2 1-284477-2 2-284477-2 3-284477-2 1540
0-284477-3 1-284477-3 2-284477-3 3-284477-3 1540
0-284478-1 1-284478-1 2-284478-1 3-284478-1 1320
0-284478-2 1-284478-2 2-284478-2 3-284478-2 1320
0-284480-1 1-284480-1 2-284480-1 3-284480-1 1100
2036
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
TAB-BRIDGE Connector System - Short Circuit
METRIC
Dimensions are
millimetres over inches
10
Blue
6
Red
6
Blue
3
Red
2
Blue
RAST 5 Version
No. of Positions
Colour Marking
as Shipped
Bridge Part Numbers
Between High Glow Wire Packaging
Cavity
Standard UL94V0 Temperature 750° no flame Unit
Numbers
1-2 0-284472-2 1-284472-2 2-284472-2 3-284472-2 5500
1-2 0-284473-3 1-284473-3 2-284473-3 3-284473-3 3520
1-2-3 0-284476-2 1-284476-2 2-284476-2 3-284476-2 1760
1-2 0-284476-3 1-284476-3 2-284476-3 3-284476-3 1760
7-8 0-284480-2 1-284480-2 2-284480-2 3-284480-2 1100
AMP MONO-SHAPE MARK II
TAB-BRIDGE Connector
System - Short Circuit
2037
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
METRIC
Dimensions are
millimetres over inches
2
Rast 5
PCB Connector System
AMP MONO-SHAPE MARK II
PCB Connector System
1PC Board
2First Circuit Path
3MONO-SHAPE Connector
4Wire
No. of Positions:
2 to 12 positions
Contact Material:
Brass
Contact Finish:
Tin Plated
Current Rating:
6 A max.
Insulation Diameter:
2.8mm max.
Insulation Resistance:
>10 M
Wire Size Range:
0.35-0.75mm
2
Temperature Range:
-40°C up to +105°C
Product Specification:
108-20214
Application Specification:
114-20104
Notes Concerning the PC
Board Layout
See also Customer Drawing
284482 and Drawing
93-330805-2 for Test PCB
Layout
1First circuit path, mate with
Connector way No. 1
2Slot for connector keying rib
Adjacent to first and/or last
way
Based on connector design,
for 3.5mm or 7.5mm length
3Hole for locking clip,
symmetric
Between two ways
(diameter 2.5)
4Slot for connector keying rib
symmetric between two
ways. Position based on
connector design, for
7.5mm length
2
1
34
3
wire exit
214
2
3
4
Green
2038
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
PCB Connector System (continued)
METRIC
Dimensions are
millimetres over inches
3
Orange
AMP MONO-SHAPE MARK II
PCB Connector System
3
Violet
3
Black
3
Green
2
Red
2
Grey
2
Orange
2
Violet
2
Black
2
Green
No. of Positions
Colour Marking
as Shipped
Part Numbers
Glow Wire Packaging
Standard UL94V0 750° no flame Unit
0-284482-1 1-284482-1 3-284482-1 5500
0-284482-2 1-284482-2 3-284482-2 5500
0-284482-3 1-284482-3 3-284482-3 5500
0-284482-4 1-284482-4 3-284482-4 5500
0-284482-5 1-284482-5 3-284482-5 5500
0-28482-6 1-284482-6 3-284482-6 5500
0-284483-1 1-284483-1 3-284483-1 3520
0-284483-2 1-284483-2 3-284483-2 3520
0-284483-3 1-284483-3 3-284483-3 3520
0-284483-4 1-284483-4 3-284483-4 3520
0-284484-1 1-284484-1 3-284484-1 2640
RAST 5 Version
2039
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
PCB Connector System (continued)
METRIC
Dimensions are
millimetres over inches
6
Grey
6
Orange
AMP MONO-SHAPE MARK II
PCB Connector System
6
Violet
6
Black
6
Green
5
Orange
5
Violet
5
Black
5
Green
4
Violet
4
Black
No. of Positions
Colour Marking
as Shipped
Part Numbers
Glow Wire Packaging
Standard UL94V0 750° no flame Unit
0-284484-2 1-284484-2 3-284484-2 2640
0-284484-3 1-284484-3 3-284484-3 2640
0-284485-1 1-284485-1 3-284485-1 2200
0-284485-2 1-284485-2 3-284485-2 2200
0-284485-3 1-284485-3 3-284485-3 2200
0-28485-4 1-284485-4 3-284485-4 2200
0-284486-1 1-284486-1 3-284486-1 1760
0-284486-2 1-284486-2 3-284486-2 1760
0-284486-3 1-284486-3 3-284486-3 1760
0-284486-4 1-284486-4 3-284486-4 1760
0-284486-5 1-284486-5 3-284486-5 1760
RAST 5 Version
2040
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
PCB Connector System (continued)
METRIC
Dimensions are
millimetres over inches
9
Orange
9
Violet
AMP MONO-SHAPE MARK II
PCB Connector System
9
Black
9
Green
8
Orange
8
Violet
8
Black
8
Green
7
Violet
7
Black
7
Green
No. of Positions
Colour Marking
as Shipped
Part Numbers
Glow Wire Packaging
Standard UL94V0 750° no flame Unit
0-284487-1 1-284487-1 3-284487-1 1540
0-284487-2 1-284487-2 3-284487-2 1540
0-284487-3 1-284487-3 3-284487-3 1540
0-284488-1 1-284488-1 3-284488-1 1320
0-284488-2 1-284488-2 3-284488-2 1320
0-28488-3 1-284488-3 3-284488-3 1320
0-284488-4 1-284488-4 3-284488-4 1320
0-284489-1 1-284489-1 3-284489-1 1100
0-284489-2 1-284489-2 3-284489-2 1100
0-284489-3 1-284489-3 3-284489-3 1100
0-284489-4 1-284489-4 3-284489-4 1100
RAST 5 Version
2041
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
PCB Connector System (continued)
METRIC
Dimensions are
millimetres over inches
AMP MONO-SHAPE MARK II
PCB Connector System
12
Violet
12
Black
12
Green
11
Violet
11
Black
11
Green
10
Black
10
Green
No. of Positions
Colour Marking
as Shipped
Part Numbers
Glow Wire Packaging
Standard UL94V0 750° no flame Unit
0-284490-1 1-284490-1 3-284490-1 1100
0-284490-2 1-284490-2 3-284490-2 1100
0-284491-1 1-284491-1 3-284491-1 880
0-284491-2 1-284491-2 3-284491-2 880
0-284491-3 1-284491-3 3-284491-3 880
0-28492-1 1-284492-1 3-284492-1 880
0-284492-2 1-284492-2 3-284492-2 880
0-284492-3 1-284492-3 3-284492-3 880
RAST 5 Version
2042
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
Application Tooling
Entry Level Semi-Automatic
IDC Bench Machines
SIM 500P
Part No. 528376-2
SIM 500T
Part No. 528377-2
In the Entry Level concept, the
application process is shared by
two different semi-automatic
machines.
The SIM 500P prepares the
AMP multifitting Mark II bando-
liered IDC connectors. The
machine removes the connector
from the chain and cuts the
keying ribs.
Next, the prepared IDC
connectors are applied by the
SIM 500T.
To facilitate this, the individual
IDC connectors are loaded into
a nest and moved automatically
into the termination station.
The manually inserted wires
are, according to a program,
terminated into the appropriate
insulation displacement slots.
The cover is then separated
from the housing, turned and
pushed into final position.
The nest, including the finished
harness module, is removed
from the easily accessed track.
Processing of all versions of
the AMP multifitting Mark II
connector system with only
minor set up changes.
Cutting and reliable removal
of the reel clips.
Cutting and reliable removal
of the coding and
polarisation ribs by means of
a preset cutting block.
Nest capacity
per machine cycle
– one connector 4- to 8-pos.
two connectors 2- and
3-pos.
– four connectors 1-position
Integrated monitoring of the
connector supply.
Simple operator interface.
Power Supply:
230 V AC, 50 Hz
Air Pressure:
6 bar
Cycle Time:
approx. 4 s / connector package
(without handling time)
Application of all versions of
the AMP multifitting Mark II
connector, with only minor
set up changes.
Termination of the wire with
active support of the IDC
contact.
Termination of two wires
(double wire termination)
programmable.
Connector fixture,
incorporating three nests for
max. 12 positions each.
Accessible and easily
interchangeable mechanical
program rail.
By utilising several
connector fixtures and
program rails, output and set
up times can be optimised.
Simple operator interface.
Power Supply:
230 V AC, 50 Hz
Air Pressure:
6 bar
Cycle Time:
approx. 1.2 s / line
(without handling time)
Technical Features Technical Data Technical Features Technical Data
SIM 500P SIM 500T
METRIC
Dimensions are
millimetres over inches
2043
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
Application Tooling (continued)
Processing Modules of the SIM 50
IDC Workstation –
SIM 50
This semi-automatic machine
was designed for the sequential
processing of AMP multifitting
Mark II IDC connector system
and its variations such as direct
and indirect mating connector
with interior or exterior locking.
A processing sequence can
consist of one or more IDC con-
nectors of the same or different
numbers of positions, but a
maximum total of 12 positions.
The specific key coding of the
connectors is performed during
the termination process by an
integrated cutting device.
The wires are manually fed into
the machine and then
automatically terminated.
Integrated control tests ensure
a high quality product.
Processing of all versions of
the AMP multifitting Mark II
connector system without
additional set up time.
Termination of the wire with
active support of the IDC
contact.
Termination of two wires
in the same slot is
programmable.
Colour coding on the
connector cover possible.
Wire exit angle can be bent
180°.
Short set up and change-
over times.
High output.
Correct wire insertion length
and key codings are
continually checked.
Good / bad sorter; faulty
connections will be destroyed.
50 different production
programs can be stored.
Operator PC interface
displaying machine status
and production data;
different languages available.
Low maintenance costs and
the capability of off-site
troubleshooting via modem.
Ergonomic and easy to oper-
ate through a Touch Screen
Display.
Power Supply:
230 V AC, 50 Hz
Air Pressure:
6 bar
Wire Size Range:
0.35 mm2up to 1.5 mm2
Insulation Diameter Range:
1.2 mm up to 3.0 mm
Wire Type:
Stranded conductors
Technical Features Technical Data
METRIC
Dimensions are
millimetres over inches
2044
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
Application Tooling (continued)
Flexible Harness Maker –
FHM
The FHM is a fully-automatic
machine featuring modular set
up. It is built to manufacture
harnesses by processing both
IDC connectors and crimp
terminals.
The basic machine includes a
12 wire selector, a station that
cuts the wires to length, a
stripping station, a double-
crimp unit, two crimping
presses and wire end ejector for
doubling and daisy chains.
A gripper unit takes the wire
from the base machine and
transfers it to the attached IDC
station. Sequential processing
allows the manufacturing of
cross-overs and bridges as well
as double-crimps, depending
on the type of IDC connector
used.
The IDC workstations are easily
reconfigured for processing our
different IDC connector
systems. They include all the
necessary processing
operations for IDC termination
with minimum change-over and
set up times.
Quality checks integrated in the
manufacturing process ensure
the highest quality harness for
every production run.
Manufacturing of harnesses
with 2.5 mm pitch IDC con-
nectors and/or 5.0 mm pitch
IDC connectors and/or with
crimp terminals.
IDC Workstations are
available for the following
connector systems:
AMP DUOPLUG 2.5
AMP DUOPLUG 2.5
Mark II
AMP DUOPLUG Power
AMP multifitting Mark II
AMP MONO-SHAPE
Mark II
The IDC Workstations can
also be used as separate
semi-automatic machines
with manual wire transfer.
The specific key coding of
the IDC connector is done on
the IDC Workstation.
Integrated test equipment
checks the coding and the
insertion depth of the wire,
and performs a continuity
test. A spark testing unit is
also available as an option.
Wire printing and single
housing insertion possible.
Operator PC interface
displays machine status and
production data; different
languages available.
Low maintenance costs and
the capability of off-site
troubleshooting via modem.
Ergonomic and easy to
operate through a Touch
Screen Display.
Power Supply:
400 V AC, 50 Hz
Air Pressure:
6 bar
Wire Size Range:
0.22 mm2up to 1.5 mm2
Wire Length:
220 mm up to 2,500 mm
Insulation Diameter Range:
1.2 mm up to 3.0 mm
Wire Type:
Stranded conductors
Technical Features Technical Data
METRIC
Dimensions are
millimetres over inches
2045
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP MONO-SHAPE MARK II
Connectors in In-Line Mating Technology
Application Tooling (continued)
IDC Harness Maker –
IHM Mark III
The new IHM Mark III is a very
high performance, fully-
automatic machine designed to
manufacture parallel jumper
harnesses using IDC tech-
nology.
The simultaneous feeding of up
to 21 wires guarantees high
productivity and flexibility and a
choice of 2.5 mm or 5.0 mm
pitch IDC systems.
The gripper unit on the left side
of the machine is able to spread
the wires in both directions to
enable the production of har-
nesses using both 2.5 mm and
5.0 mm pitch connectors at the
same time.
Available options are a stripper
crimper unit with an integrated
crimp force analyser and a
good/bad sorting unit.
The IDC workstations are easily
reconfigured for processing our
different IDC connector
systems. They include all the
necessary processing
operations for IDC termination
with minimum change-over
and set up times.
Quality checks integrated in the
manufacturing process ensure
the highest quality harness for
every production run.
Manufacturing of harnesses
using 2.5 mm and/or 5.0 mm
pitch IDC systems.
Very short wire length is
possible.
Option available to produce
harnesses with crimp
terminals on one side.
IDC Workstations are
available for the following
connector systems:
AMP DUOPLUG 2.5
AMP DUOPLUG 2.5
Mark II
AMP DUOPLUG Power
AMP multifitting Mark II
AMP MONO-SHAPE
Mark II
AMP MT Edge
The specific key coding of
the IDC connector is done on
the IDC Workstation.
Integrated test equipment
checks the coding and the
insertion depth of the wire,
and performs a continuity
test. A spark testing unit is
also available as an option.
Operator PC interface
displays machine status and
production data; different
languages available.
Low maintenance costs and
the capability of off-site
troubleshooting via modem.
Ergonomic and easy to
operate through a Touch
Screen Display.
Power Supply:
400 V AC, 50 Hz
Air Pressure:
6 bar
Wire Size Range:
0.22 mm2up to 1.5 mm2
Wire Length:
125 mm up to 2,200 mm
Insulation Diameter Range:
1.2 mm up to 3.0 mm
Wire Type:
Stranded conductors
Technical Features Technical Data
METRIC
Dimensions are
millimetres over inches
2046
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Introduction
Centerline:
5.0 mm
Available Number of Positions:
2- to 12-positions
Housing Material:
Polyamide PA 6.6
Contact Material:
CuSn, CuFe
Contact Finish:
Tin Plated, Silver Plated
Wire Size Range:
from 0.5 to 2.5mm2
Wire Size Diameter:
from 2.0 to 3.3mm
Temperature Range:
-40°C to +110°C
Current Voltage:
220 V
~
Current Rating:
max. 16 A
Standard Timer: 6 A
Power Timer: 16 A
Mating Force Contact:
15 N
Unmating Force:
8 N
Air and Creepage Distance:
3.0mm
Track Resistance:
PTI 250
Glow Wire Test:
850°C
Contacts made for Tabs
according:-
DIN 46244
(6.3 x 0.8mm / 4.8 x 0.8mm)
DIN 46343 Part 2 and 3
Technical Features
AMP Standard Timer
Connectors in In-Line
Mating Technology
AMP Standard Timer
connectors accordingto RAST
5.0 mm standard have been
developed to connect RAST 5
components (like motors,
leach pumps,water level
regulators, relays and
push-button switches) in the
Household Appliances Industry.
They meet industry
requirements, for example
multiple position connectors,
secure connection even at
inclining mating as well as a
sturdy contact design.
AMP Standard Power Timer
contacts, for use with Standard
Timer housings,are suitable for
high density and high current
capacity up to 16 A.
Housing is designed for
end-to-end stacking without
contact loss. They are available
in different keying and locking
versions from 2- positions to
12-positions.
Standard Timer contacts can be
used with stranded wires from
0.5 mm2to 2.5 mm2and can
be double terminated.Of course,
the corresponding tooling is
available, too.
AMP Standard Timer
connectors are tested by VDE
and fulfil all requirements acc.
to VDE 0700 (air gap, creepage
distance, glow wire test, ball
pressure test, creepage current
strength).
UL recognised component.
2047
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
Interior and Exterior Locking
Exterior Locking
Connection to the Components
according RAST 5 Standard
1Connected Timer Contact
2Standard Timer Housing
with Exterior Locking
3Keying
4Polarisation
5Locking Latch
6RAST 5 Tab Array
Interior Locking
Connection to the Components
according RAST 5 Standard
1Connected Timer Contact
2Standard Timer Housing
with Interior Locking
3Keying
4Polarisation
5Locking Latch
6Cover (Secondary Locking)
7RAST 5 Tab Array
Mating Direction
1
6
4
2
7
3
5
Mating Direction
1
2
3
4
5
6
2048
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Keying Plan and Housings
Keying Plan
from Mating Direction
1Locking Latch
2Keying Rib
3Keying Rib between Cavity
4Slanted Keying Rib
5Polarisation Rib
6Cavity Number
a
– 1 –
– 2 –
c
– 3 –
– 4 –
d
– 5 –
– 6 –
b
c
– 7 –
65
12
AMP Standard Timer Housings
2 Position Rast 5 Variations
3
4
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
02-A
Natural 928344-2 6-928247-2 2.500 / 2.500
c– 1 –b
a
– 2 –
d
02-B
Black
2-928344-2 0-928247-2 2.500 / 3.000
ca
– 1 –
– 2 –b
02-C
Grey 3-964951-2 8-928247-2 2.500 / 2.500
c– 1 –
a
– 2 –
d
02-D
Blue
0-964983-2 2.500
ca
– 1 –b
– 2 –
02-E
Green 6-928344-2 5-928247-2 2.500 / 2.500
a
– 1 –
– 2 –
db
02-G
Violet
5-928344-2 2-964983-2 2.500 / 2.500
– 1 –b
a
– 2 –
db
02-H
Brown
3-928344-2 2.500
a
– 1 –b
– 2 –
db
02-I
Orange
2-964951-2 3-928247-2 2.500 / 2.500
c– 1 –b
– 2 –b
Bold Part Numbers are Preferred Types
2049
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
Housings
AMP Standard Timer Housings
2 Position Rast 5 Variations (continued)
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
02-K
Yellow-Green
4-928247-2 2.500
ca
– 1 –
a
– 2 –
02-L
Natural
0-928343-2 3.000
– 1 –
– 2 –b
AMP Standard Timer Housings
2 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 7-927740-2 9-928247-2 5.000
– 1 –
– 2 –
Natural 0-964768-1 5.000
– 1 –
– 2 –b
02-M
Ultramarine-Blue
3-964983-2 2.500
ca
– 1 –
– 2 –
d
02-O
Pink
0-964951-2 2-928247-2 2.500 / 2.500
c– 1 –b
a
– 2 –
02-P
Purple
7-928247-2 2.500
c– 1 –
– 2 –
db
02-Q
Turquoise
4-928344-2 2.500
c– 1 –b
– 2 –
d
Bold Part Numbers are Preferred Types
2050
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Housings
AMP Standard Timer Housings
3 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
03-A
Natural
0--928344-3 3.000
c– 1 –b
– 2 –
d
– 3 –
03-B
Black
0-964983-3 2.500
– 1 –
d
c– 2 –b
– 3 –b
03-D
Blue
3-928247-3 2.500
a
– 1 –
– 2 –
c– 3 –
03-G
Violet
2-928247-3 2.500
ca
– 1 –
– 2 –
a
– 3 –
03-H
Brown
4-928247-3 2.500
– 1 –
– 2 –
db
– 3 –
03-K
Yellow-Green
2-964983-3 2.500
c– 1 –
– 2 –
– 3 –
db
Bold Part Numbers are Preferred Types
2051
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
Housings
AMP Standard Timer Housings
3 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 0--928343-3 3.000
a
– 1 –
– 2 –
– 3 –
Black 02-928343-3 3.000
– 1 –
– 2 –b
– 3 –
Grey 3-928343-3 3.000
– 1 –
– 2 –
a
– 3 –
Yellow 0-928247-3 2.000
– 1 –
d
– 2 –
– 3 –
db
Grey 2-928344-3 2.500
c– 1 –
a
– 2 –
– 3 –
Natural 5-928247-3 2.500
– 1 –
– 2 –
– 3 –
Bold Part Numbers are Preferred Types
2052
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Housings
AMP Standard Timer Housings
4 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
04-A
Natural 928344-4 4-928247-4 2.000 / 1.250
– 1 –b
– 2 –
c– 3 –
– 4 –
d
04-B
Black
5-928247-4 1.250
ca
– 1 –
– 2 –
– 3 –
– 4 –b
04-C
Grey
3-928344-4 0-928247-4 2.000 / 1.250
a
– 1 –
– 2 –
– 3 –
– 4 –
db
04-F
White
2-928247-4 1.250
a
– 1 –
– 2 –
a
– 3 –
– 4 –
d
03-G
Violet
3-928247-4 1.250
– 1 –
a
– 2 –
d
– 3 –
– 4 –b
AMP Standard Timer Housings
4 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 0--928343-4 2.500
– 1 –
– 2 –
– 3 –b
– 4 –
Black 02-928343-4 2.500
– 1 –
– 2 –
– 3 –
a
– 4 –
Black 3-928344-4 2.500
– 1 –
– 2 –
d
– 3 –
– 4 –
Bold Part Numbers are Preferred Types
2053
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
5 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
05-B
Black
– 1 –
– 2 –
db
– 3 –
– 4 –
– 5 –
05-D
Blue
3-928247-5 1.000
a
– 1 –
– 2 –
– 3 –
da
– 4 –
– 5 –
AMP Standard Timer Housings
5 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 0--928343-5 1.000
a
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –b
Black 02-928343-5 1.000
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
b
Green 5-928247-5 1.250
– 1 –
– 2 –
db
– 3 –
– 4 –
– 5 –
d
Yellow 4-928247-5 1.250
– 1 –
– 2 –
– 3 –b
– 4 –
c– 5 –
d
Natural 6-928247-5 1.250
c– 1 –
a
– 2 –
– 3 –
– 4 –
– 5 –
d
Bold Part Numbers are Preferred Types
2-928247-5 1.000
2054
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
6 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
06-A
Natural
964983-6 2.500
– 1 –b
– 2 –
c– 3 –
– 4 –
– 5 –
– 6 –
d
06-C
Grey
928247-6 1.000
– 1 –b
– 2 –
– 3 –
c– 4 –
– 5 –
a
– 6 –
06-D
Blue
2-928247-6 1.000
– 1 –
– 2 –b
– 3 –
– 4 –
d
– 5 –
– 6 –b
06-E
Green
3-928247-6 1.000
a
– 1 –
– 2 –
– 3 –
– 4 –
d
– 5 –
– 6 –b
Bold Part Numbers are Preferred Types
2055
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
6 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 928343-6 1.000
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –b
Black 2-928343-6 1.000
– 1 –b
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
Natural 928151-6 1.500
– 1 –
– 2 –
c– 3 –
– 4 –
d
– 5 –
– 6 –
Beige 7-928247-6 1.000
– 1 –
– 2 –
c– 3 –
– 4 –
– 5 –
– 6 –
b
Yellow 4-928247-6 1.000
– 1 –b
– 2 –
c– 3 –
– 4 –
– 5 –
a
– 6 –
Brown 5-928247-6 1.000
– 1 –
– 2 –
c– 3 –
– 4 –
– 5 –
– 6 –
Natural 6-928247-6 1.000
– 1 –b
– 2 –
– 3 –
c
– 4 –
d
– 5 –
– 6 –
Natural 2-928344-6 1.500
– 1 –b
– 2 –
– 3 –
c
– 4 –
d
– 5 –
– 6 –
Green 3-928344-6 1.500
a
– 1 –
– 2 –
b
c
– 3 –
c– 4 –
d
– 5 –
– 6 –
b
Bold Part Numbers are Preferred Types
2056
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
7 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
07-A/S
Natural
– 1 –
– 2 –
c– 3 –
– 4 –
d
– 5 –
– 6 –
c– 7 –
07-C
Grey
928247-7 700
– 1 –
– 2 –
– 3 –
d
– 4 –
– 5 –b
– 6 –
– 7 –
d
Bold Part Numbers are Preferred Types
928151-7 1.300
AMP Standard Timer Housings
7 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 928343-7 500
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
Black 2-928343-7 500
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
b
– 7 –
Natural 928344-7 500
a
– 1 –
– 2 –
c– 3 –
– 4 –
d
– 5 –
– 6 –b
c– 7 –
Blue 2-928247-7 800
– 1 –
a
– 2 –
– 3 –
– 4 –
– 5 –b
– 6 –
– 7 –
d
2-928151-7 4-928247-7
1.300 / 1.000
Green Natural
– 1 –
– 2 –
db
– 3 –
– 4 –
– 5 –
– 6 –
c– 7 –
Natural 5-928247-7 1.000
– 1 –
– 2 –
d
– 3 –b
– 4 –
– 5 –
– 6 –
– 7 –
db
Natural 6-928247-7 1.000
– 1 –
a
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
d
c
– 7 –
2057
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
8 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
08-D
Blue
928247-8 800
– 1 –
– 2 –
d
c
– 3 –
– 4 –
– 5 –
– 6 –
d
c
– 7 –
– 8 –
Bold Part Numbers are Preferred Types
AMP Standard Timer Housings
8 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 928343-8 1.000
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
Black 2-928343-8 1.000
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
Grey 3-928343-8 1.000
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
b
Natural 2-928247-7 800
a
– 1 –
– 2 –
d
– 3 –
– 4 –
– 5 –
– 6 –
d
– 7 –
– 8 –
2058
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
9 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
09-D
Blue
2-928247-9 600
– 1 –
– 2 –
– 3 –
d
– 4 –
– 5 –b
– 6 –
– 7 –
d
– 8 –
– 9 –
Bold Part Numbers are Preferred Types
AMP Standard Timer Housings
9 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 927740-9 1.000
– 1 –b
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
Natural 928151-9 1.000
– 1 –b
– 2 –
c– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –b
Yellow 928247-9 500
– 1 –
c– 2 –
– 3 –
– 4 –
a
– 5 –
– 6 –
– 7 –
– 8 –
d
– 9 –
Brown 3-928247-9 600
– 1 –
– 2 –
– 3 –b
– 4 –
– 5 –
c– 6 –
– 7 –
a
– 8 –
– 9 –
2059
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
2
Rast 5
AMP Standard Timer
Connectors in In-Line Mating Technology
Housings
AMP Standard Timer Housings
10 Position Special Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Brown 1-928247-0 1.400
– 1 –
b
– 2 –
c
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
d
–10
Grey 2-928247-0 500
– 1 –
– 2 –
d
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
c
– 8 –
– 9 –
a
–10
AMP Standard Timer Housings
11 Position Rast 5 Variations
RAST 5 Version
Keying Version
Colour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
11-B
Black
1-928247-1
1.000
Yellow
– 1 –
b
– 2 –
c
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
d
–10
–11
b
AMP Standard Timer Housings
11 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 1-927740-1 800
– 1 –
b
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
–10
–11
b
AMP Standard Timer Housings
12 Position Special Variations
VersionColour
Part
Numbers Packaging
with Interior Locking with Exterior Locking Unit
Natural 1-927740-2 700
– 1 –
– 2 –
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
b
– 9 –
–10
–11
–12
Blue 2-928247-1 1.000
– 1 –
b
– 2 –
c
– 3 –
– 4 –
– 5 –
– 6 –
– 7 –
– 8 –
– 9 –
d
–10
–11
b
Bold Part Numbers are Preferred Types
2060
Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
I/A
t/ºC
0 20406080100120
20
18
16
14
12
10
8
6
4
2
Derating Curve
AMP Standard Timer
Connectors in In-Line Mating Technology
Standard Timer Connector and Contacts
Technical Data
Material:
Brass, Tin Plated
Mating Part:
6.3 Tab
Wire:
FLK 0.5/0.75 and 1.5mm2
Current Carrying Capacity to 6A:
1 = Wire 0.50mm2, 11pos. housing
2 = Wire 0.75mm2, 11pos. housing
3 = Wire 0.50mm2, 2pos. housing
4 = Wire 0.75mm2, 2pos. housing
Current Carrying Capacity to 16A:
5 = Wire 1.50mm2, 11pos. housing
6 = Wire 1.50mm2, 2pos. housing
0.5–1.0 1.4–2.3 CuZn/Brass Tin Plated 928820-1 3.000
1.0–2.5 3.0–4.3 CuZn/Brass Tin Plated 926973-1 2.500
Wire Size Range
(mm2)
Insulation
Diameter Range
(mm) Material Finish Part Number Packaging Unit
Standard Timer Contacts
with One Locking Lance
0.5–1.0 1.4–2.3 CuZn/Brass Tin Plated 964201-1 3.000
1.0–2.5 3.0–4.3 CuZn/Brass Tin Plated 964202-1 2.000
Wire Size Range
(mm2)
Insulation
Diameter Range
(mm) Material Finish Part Number Packaging Unit
Standard Timer Contacts
with Two Locking Lances
1.0–2.5 2.2–3.0 CuFe/Copper Iron Tin Plated 964203-1 2.300
1.0–2.5 2.2–3.0 CuFe/Copper Iron Silver Plated 964203-5 2.300
1.5–3.0 max. 2 x 3.0 CuFe/Copper Iron Tin Plated 964204-1 2.000
1.5–3.0 max. 2 x 3.0 CuFe/Copper Iron Silver Plated 964204-5 2.000
Wire Size Range
(mm2)
Insulation
Diameter Range
(mm) Material Finish Part Number Packaging Unit
Standard Power Timer
Standard Power Timer
Standard Timer
5
1234
6
Current Rating
Ambient Temperature
Bold Part Numbers are Preferred Types
2061
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Engineering Notes
2
Rast 5
2062
AMP Standard Timer
Connectors in In-Line Mating Technology Catalogue 1654742
Revised 5-04
Dimensions are in inches and
millimetres unless otherwise
specified. Values in brackets
are metric equivalents.
Dimensions are shown for
reference purposes only.
Conversion Rate:
25.4mm = 1 inch
Products for Industrial &
Commercial Applications Specifications subject to
change. www.tycoelectronics.com
Engineering Notes
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
TE Connectivity:
1217004-1