96 MHz SAW Filter 5 MHz bandwidth Part Number SF0096BA02438S DESCRIPTION * * * 96 MHz SAW bandpass filter with 5 MHz bandwidth. 13.3 x 6.5 mm SMP. RoHS compliant. TYPICAL PERFORMANCE Horizontal: Vertical from Top: Frequency : Relative Magnitude : Relative magnitude : Phase Linearity : Group Delay Deviation : S11 4 10 0.8 10 100 MHz/div dB/div dB/div deg/div ns/div S22 Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02438S Rev B 22-Feb-2010 ECN 36650 Page 1 of 3 96 MHz SAW Filter 5 MHz bandwidth Part Number SF0096BA02438S SPECIFICATION Parameter 1 Center Frequency (Fc) 3 Minimum Insertion Loss 1 dB Bandwidth 15 dB Bandwidth Passband Variation (Fc +/- 1.92 MHz) Phase Linearity (Fc +/- 1.92 MHz) Group Delay Variation (Fc +/- 1.92 MHz) 2 Absolute Delay Change in Absolute Delay (from unit to unit) Absolute Delay Variation (from -40C to 55C) Input Return Loss (Fc+/-1.92 MHz) Output Return Loss (Fc+/-1.92 MHz) Rejection (40 to 87 MHz) Rejection (105 to 150 MHz) Source and Load Impedance Ambient Temperature Notes: Min 95.9 5.00 -10 10 10 43 43 - Typ 96.0 13.5 5.38 7.48 0.5 2.4 35 1.23 0 5 13 13 48 48 50 25 Max 96.1 15 8.00 0.8 5.0 80 3 10 15 - Units MHz dB MHz MHz dB p-p deg p-p ns p-p us ns ns dB dB dB dB C 1. All dB levels are referenced to the insertion loss 2. A smoothing aperture of 0.125 MHz may be applied to this measurement. 3. Average of lower and upper 3 dB frequencies; applies at 23C only. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 - 85 55 13 Units C C dBm MATCHING CIRCUIT Input 50 Single ended Typical component values: (Minimum inductor Q = 40) Output 50 Single ended Ls1 = 91 nH Lp1 = 39 nH Rp1 = 4.7 K Ls2 = 150 nH Lp2 = 47 nH Rp2 = 1.8 K Notes * Suggest the use of 2% tolerance matching components. * Tuning values shown are for reference only. Optimum values may change depending upon board layout. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02438S Rev B 22-Feb-2010 ECN 36650 Page 2 of 3 96 MHz SAW Filter 5 MHz bandwidth Part Number SF0096BA02438S PACKAGE OUTLINE SUGGESTED FOOTPRINT Units: mm Tolerances are 0.15 mm except for the overall length and width, which are nominal values. Pad Configuration: Input: 1 Output: 6 Ground: All other pads Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating ISO 9001 Registered All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice. (c) 2010 All rights reserved. Spectrum Microwave 400 Nickerson Road, Marlborough, MA 01752, USA * Phone 1-508-251-6400 * Fax 1-508-251-6401 www.SpectrumMicrowave.com DSSF0096BA02438S Rev B 22-Feb-2010 ECN 36650 Page 3 of 3