SNAP TEX Cables and Breakout Boards Features SNAP TEX Family SNAP TEX Cables SNAP TEX cables provide convenient connections from I/O modules to field wiring. Most cables are designed to connect to breakout boards; some cables have flying leads for direct connection to field devices. Description SNAP TEX Breakout Boards SNAP TEX cables and breakout boards are part of the SNAP TEX family of wiring and mounting accessories. (See form 1772 for accessories not covered in this data sheet.) These cables and boards save time and expense during installation, maintenance, and debugging by reducing the time and effort required to wire field devices to SNAP I/O modules. SNAP TEX breakout boards move terminals away from the crowded rack area for easier installation and maintenance. Some breakout boards, such as the SNAP-AIMA-HDB, work only with specific modules; others are designed to be used with several types of modules. See tables starting on page 2. Choose the cables and breakout boards for your modules based on the table that starts on page 2. Specifications and dimensions begin on page 5 and wiring diagrams on page 19. Part Numbers Part Part Numbers (continued) Part SNAP-AIMA-HDB SNAP-AIMA-HDB-FM* Breakout boards for SNAP-AIMA-32 and SNAP-AIMA-32-FM analog input modules SNAP-AIV-HDB SNAP-AIV-HDB-FM* Breakout boards for SNAP-AIV-32 and SNAP-AIV-32-FM analog modules Description Cables Description Breakout Boards SNAP-IDC-HDB SNAP-IDC-HDB-FM* Fused breakout board for SNAP 32-point digital input modules SNAP-HD-ACF6 6 ft. (1.8 m) wiring harness assembly for SNAP 16-point digital modules; flying leads SNAP-ODC-HDB SNAP-ODC-HDB-FM* Fused breakout board for SNAP 32-point digital output modules SNAP-HD-BF6 6 ft. (1.8 m) wiring harness for 32-channel modules and breakout boards SNAP-TEX-FB16-H 16-point breakout board for SNAP I/O modules, with fuses, fuse-blown indicators, & bussed power (120-240 V) SNAP-TEX-FB16-L 16-point breakout board for SNAP I/O modules, with fuses, fuse-blown indicators, & bussed power (12-24 V) SNAP-TEX-MR10-16 Mechanical relay breakout board for one 16-point or four 4-point SNAP digital output modules. SNAP-TEX-MR10-16C Mechanical relay breakout board for one 16-point or four 4-point SNAP digital output modules, or connecting two boards to one 32-point digital module. Optional jumper straps. SNAP-HD-CBF6 6 ft. (1.8 m) wiring harness for most 32-point modules, with flying leads SNAP-HD-G4F6 6 ft. (1.8 m) header cable for SNAP-ODC-32SNK and SNAP-IDC-32 digital modules and G4PB16H and G4PB16HC mounting racks. Also for SNAP-ODC-32-SRC when connecting to a SNAP-MR10-16C breakout board. 6 ft. (1.8 m) header cable for SNAP-IDC-32N SNAP-HD-G4F6N digital modules and G4PB16H and G4PB16HC mounting racks SNAP-TEX-CBE6 6 ft. (1.8 m), 8-wire cable for SNAP I/O modules. Even terminals commoned, flying leads. SNAP-TEX-CBO6 6 ft. (1.8 m), 8-wire cable for SNAP I/O modules. Odd terminals commoned, flying leads. SNAP-TEX-MR10-4 Mechanical relay breakout board for a 4point SNAP digital output module SNAP-TEX-CBS6 6 ft. (1.8 m), 8-wire cable for SNAP I/O modules. Straight-through; no common terminals. Flying leads. SNAP-TEX-32 32-point breakout board for SNAP I/O modules DATA SHEET 6 ft. (1.8 m) wiring cable for SNAP-AOVA-8 module, with flying leads Form 1756-150320 SNAP-HD-20F6 SNAP TEX Cables and Breakout Boards Extend the terminals on your SNAP I/O modules for easier, cleaner wiring to field devices. Six-foot (1.8 meter) wiring cables plug into tops of I/O modules for quick replacement. Breakout boards offer options such as fusing, power to loads, and mechanical relays. Specialty cables integrate older G4 digital I/O with SNAP PAC I/O. * Factory Mutual approved Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. PAGE 1 SNAP TEX Cables and Breakout Boards Module, Breakout Board, and Cable Compatibility Charts Look in the left column for the module you have. Choose the breakout board in the right columns. Compatible cables are shown in the table cells in the center. 4-Point Digital Modules DATA SHEET Form 1756-150320 SNAP TEX Cables and Breakout Boards Breakout Board PAGE 2 Module SNAP-TEX-32 ** SNAP-TEX-FB16-H SNAP-TEX-FB16-L SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 SNAP-TEX-MR10-16C Digital input modules--4-point SNAP-IAC5 SNAP-IAC5A SNAP-IAC5AFM SNAP-IAC5FM SNAP-IAC5MA SNAP-IDC5MA SNAP-TEX-CBS6 * SNAP-TEX-CBS6 * Not used for inputs SNAP-IDC5 SNAP-IDC5-FAST-A SNAP-IDC5-HT SNAP-IDC5D SNAP-IDC5DFM SNAP-IDC5FAST SNAP-IDC5FM SNAP-IDC5G SNAP-TEX-CBE6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 Not used for inputs SNAP-IDC5Q SNAP-TEX-CBS6 Not used Not used for inputs SNAP-IDC5-SW SNAP-IDC5-SW-NC SNAP-TEX-CBS6 Not used Not used for inputs Digital output modules--4-point SNAP-ODC5-I SNAP-ODC5-IFM SNAP-ODC5A-I SNAP-ODC5A-IFM SNAP-ODC5MA SNAP-TEX-CBS6 * SNAP-TEX-CBS6 * SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-OAC5-I SNAP-OAC5-IFM SNAP-OAC5MA SNAP-TEX-CBS6 * SNAP-TEX-CBS6 * Not used SNAP-ODC5SRC SNAP-ODC5SRCFM SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-OAC5 SNAP-OAC5FM SNAP-ODC5ASNK SNAP-ODC5R SNAP-ODC5R5 SNAP-ODC5R5FM SNAP-ODC5RFM SNAP-ODC5SNK SNAP-ODC5SNKFM SNAP-TEX-CBE6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 Not used SNAP-OMR6-A SNAP-OMR6-C Not used Not used Not used * This cable maintains channel-to-channel isolation on these modules. If channel-to-channel isolation is not important, you can also use the SNAP-TEX-CBO6 cable. ** The SNAP-TEX-32 can be used with digital outputs but has no fuses. SNAP-TEX-FB16 boards are preferable for digital outputs because they include fuses. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Module, Breakout Board, and Cable Compatibility Charts (continued) Look in the left column for the module you have. Choose the breakout board in the right columns. Compatible cables are shown in the table cells in the center. 1-, 2-, and 4-Point Analog Modules Module Breakout Board SNAP-TEX-FB16-H SNAP-TEX-FB16-L SNAP-TEX-CBS6 Not used for analog modules SNAP-TEX-CBE6 SNAP-TEX-CBS6 Not used for analog modules Analog input modules (not thermocouples) SNAP-AIARMS SNAP-AIARMS-i SNAP-AIARMS-i-FM SNAP-AICTD SNAP-AICTD-4 SNAP-AILC a SNAP-AILC-2 a SNAP-AIMA-i SNAP-AIMA-iSRC a SNAP-AIMA-iSRC-FM a SNAP-AIMA-iH SNAP-AIMA2-i SNAP-AIRATE SNAP-AIRATE-HFi SNAP-AIRTD SNAP-AIRTD-10 SNAP-AIRTD-1K SNAP-AIV-72 SNAP-AIV-i SNAP-AIV2-i SNAP-AIVRMS SNAP-AIVRMS-i SNAP-AIVRMS-i-FM SNAP-AIMA SNAP-AIMA-4 SNAP-AIMV2-4 SNAP-AIMV-4 SNAP-AIR40K-4 SNAP-AIV SNAP-AIV-4 SNAP-AIPM SNAP-AITM-i c b SNAP-AIPM-3 SNAP-AIPM-3V SNAP-AIR400K-8 SNAP-AITM c SNAP-AITM-2 c SNAP-AITM-4i c SNAP-AITM2-i SNAP-pH/ORP No cable available Not used for analog modules c Analog output modules SNAP-AOA-23 SNAP-AOA-28 SNAP-TEX-CBE6 SNAP-TEX-CBS6 Not used for analog modules SNAP-AOA-3 SNAP-AOV-5 SNAP-TEX-CBE6 SNAP-TEX-CBO6 SNAP-TEX-CBS6 Not used for analog modules SNAP-AOV-25 SNAP-AOV-27 SNAP-TEX-CBO6 Not used for analog modules SNAP-AOD-29 SNAP-AOD-29-HFi SNAP-TEX-CBS6 Not used for analog modules SNAP-AOA-23-iH SNAP-AOA-23-iSRC a SNAP-AOA-23-iSRC-FM a (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com DATA SHEET a Note that the SNAP-TEX-SBS6 cable does not include a connector for the 2-pin terminal on top of these modules, required for excitation voltage. b Not recommended for use with breakout boards due to CT safety concerns. c Do not use breakout boards with thermocouples. SNAP TEX Cables and Breakout Boards SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 SNAP-TEX-MR10-16C SNAP-TEX-32 PAGE 3 SNAP TEX Cables and Breakout Boards High-Density Digital Modules Breakout Board Module SNAP TEX Cables and Breakout Boards SNAP-TEX-32 SNAP-TEX-FB16-H SNAP-TEX-FB16-L SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 SNAP-TEX-MR10-16C SNAP-IDC-HDB SNAP-ODC-HDB SNAP-IDC-HDB-FM SNAP-ODC-HDB-FM Without a breakout board SNAP-IAC-16 SNAP-IAC-A-16 SNAP-IAC-K-16 SNAP-IDC-16 SNAP-IDC-HT-16 SNAP-HD-ACF6 (2 modules/board) SNAP-HD-ACF6 Not used with inputs Not used Not used SNAP-HD-ACF6 SNAP-IDC-32 SNAP-IDC-32-FM SNAP-IDC-32N SNAP-IDC-32D SNAP-IDC-32DN SNAP-HD-CBF6 SNAP-HD-CBF6 (2 boards/module) Not used with inputs SNAP-HD-BF6 Not used SNAP-HD-CBF6 Do not use Not used SNAP-HD-CBF6 SNAP-HD-CBF6 (2 boards/module) SNAP-HD-CBF6 SNAP-HD-G4F6 (MR10-16C only) SNAP-HD-BF6 SNAP-HD-CBF6 Not used SNAP-ODC-32-SNK SNAP-ODC-32-SNK-FM SNAP-ODC-32-SRC SNAP-ODC-32-SRC-FM Analog Modules with More Than 4 Points Breakout Board Module SNAP-TEX-32 SNAP-AICTD-8 SNAP-AIMA-8 SNAP-AITM-8 ** SNAP-AITM-8-FM ** SNAP-AIV-8 Can be used; no cable currently available SNAP-AIMA-32 SNAP-AIMA-32-FM Not recommended SNAP-AIV-32 SNAP-AIV-32-FM SNAP-HD-CBF6 SNAP-AOVA-8 SNAP-HD-20F6 SNAP-TEX-FB16-H SNAP-TEX-FB16-L SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 SNAP-TEX-MR10-16C SNAP-IDC-HDB SNAP-IDC-HDB-FM SNAP-ODC-HDB SNAP-ODC-HDB-FM SNAP-AIMA-HDB SNAP-AIMA-HDB-FM SNAP-AIV-HDB SNAP-AIV-HDB-FM Not used Not used with analog modules SNAP-HD-BF6 Not used Without a breakout board No cable available SNAP-HD-BF6* Not recommended SNAP-HD-BF6 SNAP-HD-CBF6 Not used SNAP-HD-20F6 DATA SHEET Form 1756-150320 * For specific applications. See details in wiring diagrams. ** Do not use breakout boards with thermocouples. PAGE 4 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Cables for 1-, 2-, or 4-pt modules: SNAP-TEX-CBO6, SNAP-TEX-CBE6, SNAP-TEX-CBS6 These three cables provide neat, protected wiring from the top of a 1-, 2-, or 4-point module to the breakout board. Each cable snaps into the top of one module and terminates at the breakout board with 18-gauge, color-coded flying leads, already stripped and tinned and ready for wiring. The leads attach easily to the breakout board with spring connectors. SNAP-TEX-CBS6--No common terminals; wiring is straight through. See the tables starting on page 2 to determine the correct cable for your module and breakout board. This photo shows the contrast between a regularly wired SNAP PAC rack (at upper left) and one using SNAP-TEX-CBE6, -CBO6, and -CBS6 cables (at lower right). The cables protect top-of-module connections and wires, and make it easier to follow wiring to field devices. Cables terminate in color-coded flying leads, already stripped, tinned, and ready for wiring. SNAP TEX Cables and Breakout Boards SNAP-TEX-CBO6--Odd-numbered terminals are commoned. SNAP-TEX-CBE6--Even-numbered terminals are commoned. Installation, maintenance, and troubleshooting are faster and simpler using SNAP TEX cables. Form 1756-150320 DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. PAGE 5 SNAP TEX Cables and Breakout Boards Cables for 1-, 2-, or 4-point modules (continued) Cable Specifications See the tables starting on page 2 for module, cable, and breakout board compatibility. DATA SHEET SNAP-TEX-CBO6 SNAP-TEX-CBE6 SNAP-TEX-CBS6 6 feet (1.8 meters) 6 feet (1.8 meters) 6 feet (1.8 meters) Connector 8 pins, 0.2 in. (5.08 mm) centerto-center 8 pins, 0.2 in. (5.08 mm) center-to- 8 pins, 0.2 in. (5.08 mm) centercenter to-center Wires 8 pre-stripped, tinned, colorcoded, 18 gauge 8 pre-stripped, tinned, colorcoded, 18 gauge 8 pre-stripped, tinned, colorcoded, 18 gauge Bussing Odd-numbered pins connected Even-numbered pins connected* No connections Agency Approvals CE, RoHS, DFARS CE, RoHS, DFARS CE, RoHS, DFARS Warranty 30 months 30 months 30 months *Do NOT USE the CBE6 with a SNAP-TEX-FB16-H or -L breakout board. The FB16s have odd-numbered pins connected. Wire Colors Point Pin Color wire 1 black 2 red 3 blue 0 Point Pin Color wire 5 yellow 6 brown 7 red/black 8 blue/black 2 1 3 4 orange Wiring diagrams begin on page 19. Form 1756-150320 SNAP TEX Cables and Breakout Boards Feature Cable length PAGE 6 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Cable for 8-point analog output module: SNAP-HD-20F6 The SNAP-HD-20F6 cable is designed for use with an 8-channel SNAP-AOVA-8 analog output module. The cable has a 20-pin connector at the module end and flying leads for field wiring. SNAP-AOVA-8 Module (from top) SNAP-HD-20F6 Cable Wire colors - Excitation LED - indicates excitation 24 VDC excitation Not used Ch 0 Ch 1 Ch 2 Ch 3 Outputs Ch 4 Ch 5 Ch 6 Ch 7 - + 24 VDC Power Supply This supply is isolated from the module outputs. - + Current input - + Voltage input All negative output terminals are tied together internally. All current from any output is sourced from the module. No external excitation supplies allowed. - + 24 VDC Color - Black + White with Black Wire colors - Output points Ch -/+ - Color Blue 0 + White with Blue - Pink + White with Pink - Gray 1 2 + White with Gray - Green + White with Green - Orange + White with Orange - Red 3 4 SNAP TEX Cables and Breakout Boards You can also use the cable and module with a SNAP-TEX-32 breakout board (four modules per board). See page 27 for a wiring diagram. 5 + White with Red - Purple + White with Purple - Yellow + White with Yellow 6 7 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 NOTE: Yellow with purple and purple with yellow wires are not used. DATA SHEET For more information on the SNAP-AOVA-8 module, see form 1066, the SNAP Analog Output Modules Data Sheet. PAGE 7 SNAP TEX Cables and Breakout Boards Cables for 16- or 32-point modules: SNAP-HD-ACF6, SNAP-HD-CBF6, SNAP-HD-BF6 DATA SHEET Form 1756-150320 SNAP TEX Cables and Breakout Boards The SNAP-HD-ACF6, SNAP-HD-CBF6, and SNAP-HD-BF6 cables connect 16- and 32-channel modules to field wiring or breakout boards. Each cable is 6 ft. (1.8 m) long. PAGE 8 The SNAP-HD-ACF6 and the SNAP-HD-CBF6 have connectors at one end that attach to the top of a module and flying leads at the other end for field wiring. The ACF6 is for 16-channel modules and includes two cables, each cable wiring 8 channels. The CBF6 is for 32-channel modules. SNAP-HD-CBF6 The SNAP-HD-BF6 has connectors at both ends, one for a 32-channel module and the other for a suitable breakout rack. SNAP-HD-ACF6 SNAP-HD-BF6 Cable Specifications See tables starting on page 2 for detailed module, cable, and breakout board compatibility. Wiring diagrams begin on page 19. Feature SNAP-HD-ACF6 SNAP-HD-CBF6 SNAP-HD-BF6 Cable length 6 feet (1.8 meters) 6 feet (1.8 meters) 6 feet (1.8 meters) Connectors Two-cable assembly; 16-pin connector at module end; flying leads at other end One 40-pin connector at module end; flying leads at other end One connector at module end; one connector at breakout board end Wires Pre-stripped, tinned, colorcoded, 22-gauge wires Pre-stripped, tinned, colorcoded, 24-gauge wires 24 gauge wires Use with Modules: SNAP-IAC-16 SNAP-IAC-A-16 SNAP-IAC-K-16 SNAP-IDC-16 SNAP-IDC-HT-16 Modules: SNAP-IDC-32 SNAP-IDC-32-FM SNAP-IDC-32N SNAP-IDC-32D SNAP-IDC-32DN SNAP-ODC-32-SNK SNAP-ODC-32-SNK-FM SNAP-ODC-32-SRC SNAP-ODC-32-SRC-FM SNAP-AIV-32 SNAP-AIV-32-FM Modules to breakout boards (regular and -FM versions): SNAP-IDC-32 to SNAP-IDC-HDB SNAP-IDC-32N to SNAP-IDC-HDB SNAP-IDC-32D to SNAP-IDC-HDB SNAP-IDC-32DN to SNAP-IDC-HDB SNAP-ODC-32-SNK to SNAP-ODC-HDB SNAP-ODC-32-SRC to SNAP-ODC-HDB SNAP-AIV-32 to SNAP-AIV-HDB SNAP-AIMA-32 to SNAP-AIMA-HDB SNAP-AIMA-32 to SNAP-AIV-HDB * Agency Approvals CE, RoHS, DFARS CE, RoHS, DFARS CE, RoHS, DFARS Warranty 30 months 30 months 30 months * Special application; see wiring diagrams Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Cables to connect G4 to SNAP: SNAP-HD-G4F6, SNAP-HD-G4F6N Each cable connects two 16-channel mounting racks to one 32-point digital module. Cables can also be used to connect G1 mounting racks with header connectors to these modules. See the table below for module and rack compatibility. The SNAP-HD-G4F6 and cables are used to connect a SNAP high-density digital (HDD) module to G4 mounting racks in order to integrate older G4 (or even G1) digital output systems with modern PAC Project software and SNAP PAC Ethernetbased controllers. For more information on HDD modules, see form #1556, the SNAP High-Density Digital Module Data Sheet. SNAP-HD-G4F6 header cable G4PB16H mounting racks In this photo, the SNAP-HD-G4F6 header cable connects a single SNAP-ODC-32-SNK digital output module on a SNAP PAC mounting rack to two G4PB16H mounting racks. NOTE: Do not use this cable with a SNAP-ODC-32-SRC module when connecting to G4 mounting racks. SNAP-ODC-32-SNK module NOTE: If there is a mismatch between the cable connector and the header connector, please contact Opto 22 Product Support. SNAP mounting rack Cable Specifications Feature SNAP-HD-G4F6 SNAP-HD-G4F6N Cable length 6 feet (1.8 meters) 6 feet (1.8 meters) Connectors One connector at module end; two header connectors at rack end One connector at module end; two header connectors at rack end Use with 32-point digital output modules 32-point digital input modules Agency approvals CE, RoHS, DFARS CE, RoHS, DFARS Warranty 30 months 30 months SNAP-HD-G4F6 cable SNAP TEX Cables and Breakout Boards The SNAP-HD-G4F6 cable can also be used to connect two SNAP-TEX-MR10-16C breakout boards to one 32-point digital module. See "Breakout Board with Mechanical Relays, Highvoltage" on page 14. For outputs, this connection makes available the G4 output's up to 3-amp switching and sensing capability, which can provide twelve times the 0.25 amp capability of the highdensity digital modules themselves. (For G4 module specs, see Opto 22 form #727, the G4 Digital I/O Data Book.) Compatible Modules and Racks Cable Modules Racks Integrated I/O SNAP-HD-G4F6 SNAP-ODC-32-SNK G4PB16H SNAP-ODC-32-SNK-FM G4PB16HC PB16H PB16HC SNAP-HD-G4F6N SNAP-IDC-32N* SNAP-IDC-32DN* PB16H PB16HC G4PB16H G4PB16HC PB16L - NOTE: While not designed for this use, it is possible to connect the SNAP-IDC-32 module with G4 15 or 24 V inputs using a SNAP-HD-G4F6 cable. However, the SNAP-IDC-32 uses positive-true logic and therefore returns the inverse of the typical negative-true logic. For example, if the SNAP-IDC-32 is controlled by a PAC Control strategy, an "OFF" state from it actually indicates that the associated G4 module is turned ON. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 Pin 1 DATA SHEET * For 15 volt or 24 volt G1 or G4 modules, use the SNAP-IDC-32N. For 5 volt modules, use the SNAP-IDC-32DN. G4PB16L PAGE 9 SNAP TEX Cables and Breakout Boards Breakout Boards: SNAP-TEX-32, SNAP-TEX-FB16-H, SNAP-TEX-FB16-L goes out to solenoids or switches, depending on the module you're using. These breakout boards are used primarily for digital inputs and outputs. DATA SHEET Form 1756-150320 SNAP TEX Cables and Breakout Boards The SNAP-TEX-32 is a simple breakout board with straightthrough wiring. Designed primarily for 2- and 4-point analog inputs/outputs and for 4-point digital inputs, the breakout board is used with SNAP-TEX cables. The board can be used with digital outputs, but it does not have fuses. PAGE 10 CAUTION: Odd pins on the SNAP-TEX-FB16-H and SNAP-TEXFB16-L breakout boards are commoned. Use only straightthrough or odd cables with these boards. The SNAP-TEX-32 can also be used with 8-, 16-, or 32-point SNAP analog modules (not thermocouples). See the table beginning on page 2 for recommended cable and board combinations for your modules. The SNAP-TEX-FB16-H and SNAP-TEX-FB16-L breakout boards provide a fuse and a fuse-blown indicator for each of their 16 channels. In addition, they provide power to loads: the SNAP-TEX-F16-H provides 120-240 volts, and the SNAPTEX-F16-L provides 12-24 volts. Simply attach the power source to a single spot in the middle of the rack, and power SNAP-TEX-FB16-H Specifications See the table beginning on page 2 for recommended cable and board combinations. Wiring diagrams begin on page 19. Feature SNAP-TEX-32 SNAP-TEX-FB16-H SNAP-TEX-FB16-L Use with I/O modules 2- or 4-point analog inputs/outputs; 4-point digital inputs and outputs 4-point digital inputs/outputs*; 8-, 16-, or 32-point digital and analog 16- and 32-pt digital inputs/outputs outputs (not thermocouples) 4-point digital inputs and outputs 16- and 32-pt digital inputs/outputs Use with cables SNAP-TEX-CBE6 (even pins connected), SNAP-TEX-CBO6 (odd pins connected), or SNAP-TEXCBS6 (no connections), depending on module. SNAP-HD-20F6 with a SNAP-AOVA-8 module. 4-ch modules: SNAP-TEX-CBO6 (odd pins connected)** or SNAPTEX-CBS6 (straight-through), depending on module. 16-ch modules: SNAP-HD-ACF6 32-ch modules: SNAP-HD-CBF6 4-ch modules: SNAP-TEX-CBO6 (odd pins connected)** or SNAPTEX-CBS6 (straight-through), depending on module. 16-ch modules: SNAP-HD-ACF6 32-ch modules: SNAP-HD-CBF6 Connectors 32 spring connectors; accommodates eight 4-point modules 16 spring connectors; accommodates four 4-point modules 16 spring connectors; accommodates four 4-point modules Fusing none 1 A, 250 V, fast-acting fuse for each I/O point (16 total). Replace with Opto 22 PN FUSE01G4 1 A, 250 V, fast-acting fuse for each I/O point (16 total). Replace with Opto 22 PN FUSE01G4 Indicators none 1 blown-fuse LED per fuse (16 LEDs total) 1 blown-fuse LED per fuse (16 LEDs total) Bussed power none 120-240 V 12-24 V Agency ApprovCE, RoHS, DFARS als CE, RoHS, DFARS CE, RoHS, DFARS Warranty 30 months 30 months 30 months * Can be used with digital outputs but does not have fuses. SNAP-TEX-FB16 boards have fuses; they are better for digital outputs. ** IMPORTANT: Do NOT USE the FB16 breakout boards with a SNAP-TEX-CBE6 cable. The board has odd pins connected; the cable has even pins connected. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Breakout Boards: SNAP-TEX-32, SNAP-TEX-FB16-H, SNAP-TEX-FB16-L (continued) Dimensions--SNAP-TEX-32 Breakout Board Dimensions are shown in inches (with centimeters in parentheses). Dimensions are shown in inches (with centimeters in parentheses). SNAP TEX Cables and Breakout Boards Dimensions--SNAP-TEX-FB16-H and SNAP-TEX-FB16-L Breakout Boards Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 11 SNAP TEX Cables and Breakout Boards Breakout Boards with Mechanical Relays: SNAP-TEX-MR10-4, SNAP-TEX-MR10-16, and SNAP-TEX-MR10-16C SNAP TEX Cables and Breakout Boards The SNAP-TEX-MR10-4, SNAP-TEX-MR10-16, and SNAP-TEX-MR10-16C breakout boards, designed for high-current switching, feature mechanical relays that can switch up to 10 A per channel. (Standard SNAP output modules can switch up to 0.75 A; SNAP-OMR6 output modules can switch up to 6 A.) These breakout boards include on/off indicators for each channel, and each channel can be wired for normally closed or normally open. The boards require 24 VDC power. A replacement relay is available, part number SNAP-MR10. NOTE: Transient protection must be used on inductive loads. SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 DATA SHEET Form 1756-150320 SNAP-TEX-MR10-16C PAGE 12 With the SNAP-TEX-MR10-16C, you can connect digital output modules in two ways: * Connect four standard 4-point ODC modules using the two spring connectors and the appropriate cable for the modules. See page 25. * Connect one SNAP-ODC-32-SRC high-density module to the header connectors on two MR10-16C breakout boards. Requires a SNAP-HD-G4F6 cable (see page 39). Also, bussed commons in 2-channel groups provide easier wiring of loads. Bussing straps (STRAP2Q and STRAP4Q) can be used for quick common power connections between relay groups. See page 26. Mechanical relays Pin 1 for header connector Spring connectors for standard, 4-point ODC modules Header connector for high-density SNAP-ODC-32-SRC module Field connectors Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Breakout Boards with Mechanical Relays (continued) Specifications See the tables beginning on page 2 for compatible modules and cables. Wiring diagrams begin on page 19. Feature SNAP-TEX-MR10-4 SNAP-TEXMR10-16 SNAP-TEX-MR10-16C SNAP-ODC5-i, SNAP-ODC5A-i, SNAP-ODC5SRC, SNAP-ODC-32-SRC SNAP-ODC5-i, SNAP-ODC5A-i, SNAP-ODC5SRC, SNAP-ODC-32-SRC Use with cables SNAP-TEX-CBO6 (odd pins bussed), SNAP-TEX-CBS6 (no bussing), or SNAP-HD-CBF6, depending on module Use with jumper straps --- STRAP2Q, STRAP4Q SPDT (1 Form C) SPDT (1 Form C) Typical life expectancy (Electrical): 1 x 105 Typical life expectancy (Electrical): 1 x 105 Switching capacity 10 A @ 240 VAC 10 A @ 240 VAC Switch On time 7 ms nominal 7 ms nominal Switch Off time 3 ms nominal 3 ms nominal Fusing 24 V fuse for board. Opto 22 p/n SNAP-FUSE1AC 24 V fuse for board. Opto 22 p/n SNAP-FUSE1AC Indicators On/Off status indicators (one for each channel) 1 fuse-blown indicator On/Off status indicators (one for each channel) 1 fuse-blown indicator Power requirements (all positions On) 24 VDC @ 75 mA 24 VDC @ 300 mA Agency Approvals CE, RoHS, DFARS CE, RoHS, DFARS Warranty 30 months from date of manufacture 30 months from date of manufacture * Relay contacts For one high-density SNAP-ODC-32-SRC module, use a SNAP-HD-G4F6 cable to connect two breakout boards to one module. For four 4-point modules, use SNAP-TEX-CBO6 (odd pins bussed) or SNAP-TEX-CBS6 (no bussing), depending on module. * SNAP TEX Cables and Breakout Boards Use with I/O modules Dimensional Drawing--SNAP-TEX-MR10-4 Breakout Board Dimensions are shown in inches (with centimeters in parentheses). Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 13 SNAP TEX Cables and Breakout Boards Breakout Board with Mechanical Relays, High-voltage Dimensional Drawing--SNAP-TEX-MR10-16 Breakout Board DATA SHEET Dimensional Drawing--SNAP-TEX-MR10-16C Breakout Board Dimensions are shown in inches (with centimeters in parentheses). Form 1756-150320 SNAP TEX Cables and Breakout Boards Dimensions are shown in inches (with centimeters in parentheses). PAGE 14 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Breakout Boards for 32-point Digital Modules: SNAP-IDC-HDB, SNAP-ODC-HDB SNAP-IDC-HDB, SNAP-IDC-HDB-FM, SNAP-ODC-HDB, and SNAP-ODC-HDB-FM breakout boards provide LED indicators and easily accessible fused connectors for points on 32-point digital input or output modules. Wiring diagrams begin on page 32. SNAP-IDC-HDB and SNAP-IDC-HDB-FM Breakout Racks for High-Density Digital Input Modules Used with SNAP-IDC-32, SNAP-IDC-32-FM, SNAP-IDC-32N, and SNAP-IDC-32DN Connectors 40-pin header connects to 32-point input module using SNAP-HD-BF6 header cable. 32 signal input connectors; each signal connector has a corresponding common connector. For each zone of 8 signal inputs, 1 connection for either module common or field common. Indicators 1 LED for On/Off status of each signal input (32 signal LEDs total) 1 power status LED for each zone of 8 signal inputs (4 power LEDs total) Fusing 2 fuses (Module Common, Field Common) for each zone of 8 signal inputs (8 fuses total) 1 A fuses; replace with Pudenz 1 A automobile mini-fuse or equivalent. Jumpers For each zone of 8 signal inputs, 1 jumper controls whether module common or field common is used. Set jumpers to X position for digital input modules. Voltage 32 VDC maximum, 12-24 VDC nominal Agency Approvals SNAP-IDC-HDB: UL, CE, RoHS, DFARS SNAP-IDC-HDB-FM: FM, CE, RoHS, DFARS Warranty 30 months from date of manufacture SNAP TEX Cables and Breakout Boards Specifications SNAP-ODC-HDB and SNAP-ODC-HDB-FM Breakout Racks for High-Density Digital Output Modules Connectors 40-pin header; connects to 32-point sourcing or sinking module using SNAP-HD-BF6 header cable. 32 signal output connectors; each signal connector has a corresponding common connector. For each zone of 8 signal outputs, 1 connection for either module common or field common. Indicators 1 LED for On/Off status of each signal output (32 signal LEDs total) 1 power status LED for each zone of 8 signal outputs (4 power LEDs total) Fusing 1 A fuses; 1 fuse for each signal output (32 signal fuses total) Replace with Pudenz 1 A automobile mini-fuse or equivalent. Jumpers For each zone of 8 signal inputs, 1 jumper controls whether module common or field common is used. Set jumpers to Z position for digital output modules. Voltage 32 VDC maximum, 12-24 VDC nominal Agency Approvals SNAP-ODC-HDB: UL, CE, RoHS, DFARS SNAP-ODC-HDB-FM: FM, CE, RoHS, DFARS Warranty 30 months from date of manufacture Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 SNAP-ODC-32-SRC, SNAP-ODC-32-SRC-FM, SNAP-ODC-32-SNK, and SNAP-ODC-32-SNK-FM DATA SHEET Used with PAGE 15 SNAP TEX Cables and Breakout Boards Breakout Boards for 32-point Digital Modules (continued) SNAP TEX Cables and Breakout Boards Dimensional Drawings X Z X Z X Z X Z SNAP-IDC-HDB and SNAP-IDC-HDB-FM breakout racks Z Z X X X Z X Z DATA SHEET Form 1756-150320 SNAP-ODC-HDB and SNAP-ODC-HDB-FM breakout racks PAGE 16 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Breakout Boards for 32-point Analog Modules: SNAP-AIMA-HDB and SNAP-AIV-HDB readings you need. This section applies only to the SNAPAIMA-HDB board. Changing Negative to Positive Values SNAP-AIMA-HDB breakout board SNAP-AIMA-HDB, SNAP-AIMA-HDB-FM, SNAP-AIV-HDB, and SNAP-AIV-HDB-FM breakout boards are primarily designed for use with SNAP-AIMA-32, SNAP-AIMA-32-FM, SNAP-AIV-32, and SNAP-AIV-32-FM analog input modules, respectively. Each of these modules provides 32 input points. The breakout boards provide easy accessibility for wiring points to field devices. Use the SNAP-HD-BF6 cable for wiring connections between the module and the breakout board. Note for the SNAP-AIMA-32 or SNAP-AIMA-32-FM: if you are using one of these modules with loop powered (2-wire) devices, connect to the SNAP-AIMA-HDB or SNAP-AIMAHDB-FM rack as shown on page 40. However, if you are using the SNAP-AIMA-32 (or -FM) with self-powered devices (4wire), do not use the SNAP-AIMA-HDB (or -FM) boards, which have a current limiter. Instead, wire to the SNAP-AIV-HDB or SNAP-AIV-HDB-FM as shown on page 41 (negative common) or page 42 (positive common). CAUTION: We strongly recommend that you use a breakout board with the SNAP-AIMA-32 (or -FM) module. Without the board, miswiring of any point on the module can cause severe out-of-warranty damage. The breakout board protects the module from many wiring errors. This may seem odd, but it works. Don't be confused by the "Lower" and "Upper" labels for the values. Positive values sent to the module will be shown as the correct positive values within your PAC Control strategy. Scaling Values Similarly, if you need to scale values for your application, enter the positive values you need. If you want the field signal of 4 to 20 mA to be scaled as 0 to 100%, then configure as shown below: SNAP TEX Cables and Breakout Boards (SNAP-AIMA-HDB board only) To read positive values, when you configure points on the module, choose the scalable option and enter the corresponding positive values, like this: Working with Module Values Form 1756-150320 Because these readings are negative values, they can be confusing to work with. This section shows you how to easily change them to positive values or scale them to the positive Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET AIMA modules used with a SNAP-AIV-HDB board read normally. However, values on AIMA modules used with a SNAP-AIMA-HDB board are read as negative values. For example, a value of 10 mA on the module will be read as -10 mA. (Note: If no readings appear, try reversing field connections on the board.) PAGE 17 SNAP TEX Cables and Breakout Boards Breakout Boards for 32-point Analog Modules (continued) DATA SHEET Dimensional Drawing--SNAP-AIV-HDB and SNAP-AIV-HDB-FM Breakout Boards Form 1756-150320 SNAP TEX Cables and Breakout Boards Dimensional Drawing--SNAP-AIMA-HDB and SNAP-AIMA-HDB-FM Breakout Boards PAGE 18 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring Diagrams for Cables and Breakout Boards Module Type To Breakout Board See page SNAP-TEX-32 20 SNAP-TEX-FB16-H SNAP-TEX-FB16-L 21 SNAP-TEX-MR10-4 SNAP-TEX-MR10-16 24 4-point digital modules 25 SNAP-TEX-32 20 8-point analog output module SNAP-TEX-32 27 SNAP-TEX-32 28 SNAP-TEX-FB16-H SNAP-TEX-FB16-L 29 SNAP-TEX-MR10-16C 26 SNAP-TEX-32 30 SNAP-TEX-FB16-H SNAP-TEX-FB16-L 31 32-point digital inputs SNAP-IDC-HDB 32 32-point digital outputs SNAP-ODC-HDB 35 SNAP-TEX-MR10-16 38 SNAP-TEX-MR10-16C 39 32-point SNAP-AIMA-32 SNAP-AIMA-HDB 40 32-point SNAP-AIV-32 SNAP-AIV-HDB 41 32-point SNAP-AIV-32 SNAP-TEX-32 30 16-point digital modules 32-point digital modules 32-point digital outputs (sourcing only) SNAP TEX Cables and Breakout Boards SNAP-TEX-MR10-16C 1-, 2-, or 4-point analog modules Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 19 SNAP TEX Cables and Breakout Boards Wiring: 4-Point Digital or Analog Module to SNAP-TEX-32 Breakout Board Wire up to eight 4-point modules to the SNAP-TEX-32. Only one module is shown below. 1 Black DATA SHEET Cable: SNAP-TEX-CBO6 SNAP-TEX-CBE6 SNAP-TEX-CBS6 Find the appropriate cable for your module in the tables starting on page 2. 3 Blue 4 Orange 5 Yellow 6 Brown SNAP-TEX-32 breakout board For field wiring, see the data sheet for the module you are using. 7 Red/blk 8 Blue/blk Form 1756-150320 SNAP TEX Cables and Breakout Boards 2 Red PAGE 20 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 4-Point Digital Module to SNAP-TEX-FB16-H or SNAP-TEX-FB16-L Board General Instructions SNAP-TEX-FB16-H or SNAP-TEX-FB16-L breakout board 3 5 MODULE COMMON FUSE COMMON 8 7 Connect channel 0 load to field terminals 1 and 2. Connect channel 1 load to terminals 3 and 4. And so on. For AC output modules: Connect the hot wire to one of the Fuse Common terminals. For DC output modules: See "Polarity and Module Type" on page 22 Connect the neutral wire to one of the Module Common terminals. NOTE: Extra terminals are provided to daisy-chain power to multiple breakout boards. SNAP-TEX-FB16-H or SNAP-TEX-FB16-L breakout board SNAP TEX Cables and Breakout Boards 1 2 Load 1 Load 1 SNAP-ODC5 Load 2 Fuse Common Example for the SNAP-ODCSNK and SNAP-ODC5ASNK modules. The polarity depends on which SNAP ODC module is used. See page 22. (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com DATA SHEET Module Common PAGE 21 SNAP TEX Cables and Breakout Boards DATA SHEET Polarity and Module Type When using DC output modules, the polarity for connecting the DC power source to the Module Common and Fuse Common terminals on the breakout board depends on the SNAP digital output module being used. The SNAP-TEX-FB16-H and SNAP-TEX-FB16-L breakout boards use the Module Common to connect to all the odd terminals of the SNAP output module. Fuse Common goes to the individual fuses, which go to the odd terminals on this breakout board. The even terminals on the SNAP output modules go to the even terminals via the SNAP-TEX cable. SNAP-ODC5SNK, SNAP-ODC5ASNK These modules internally tie all odd terminals together. * Connect the positive side of the DC power source to Fuse Common. * Connect the negative side of the DC power source to Module Common. SNAP-ODC5SRC This module internally ties all even terminals together. * Connect the positive side of the DC power source to Module Common. * Connect the negative side of the DC power source to Fuse Common. SNAP-ODC5MA, SNAP-ODC5-i, SNAP-ODC5A-i IMPORTANT: The points on these modules are isolated from each other. However, when used with this breakout board, the channel-to-channel isolation is bypassed, because this breakout board ties the module's odd terminals together. * Connect the positive side of the DC power source to Module Common. * Connect the negative side of the DC power source to Fuse Common. Form 1756-150320 SNAP TEX Cables and Breakout Boards 4-point Digital Module to SNAP-TEX-FB16-H or SNAP-TEX-FB16-L (continued) PAGE 22 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards 4-point Digital Module to SNAP-TEX-FB16-H or SNAP-TEX-FB16-L (continued) Resistor Fuse Blown-fuse LED CAUTION: Do NOT use the SNAP-TEX-CBE6 (even pins commoned) cable with this board. The board has odd pins commoned. LED Fuse Cable: SNAP-TEX-CBO6 SNAP-TEX-CBS6 Find the appropriate cable for your module in the tables starting on page 2. Also see "General Instructions" on page 21. SNAP TEX Cables and Breakout Boards Resistor Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 23 SNAP TEX Cables and Breakout Boards Wiring: 4-point Digital Module to SNAP-TEX-MR10-4 or SNAP-TEX-MR10-16 Board The example shows wiring for the first two points on a SNAP-ODC5-i module to a SNAP-TEX-MR10-4 board. Wiring connections shown are for a SNAP-TEX-CBO6 cable. SNAP TEX Cables and Breakout Boards Wiring 4-point modules to a SNAP-TEX-MR10-16 board is similar. The MR10-16 has 16 channels rather than four. Module: SNAP-ODC5-i Cable: SNAP-TEX-CBO6 For other module/cable options with this board, see page 2. Field wiring For normally open (N.O.) or normally closed (N.C.) DATA SHEET Form 1756-150320 NOTE: Transient protection must be used on inductive loads. PAGE 24 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 4-point Digital Output Module to SNAP-TEX-MR10-16C Board Two 4-point ODC modules can be wired to each of the two spring connectors. The example shows the first two points on a SNAP-ODC5-i module. Wiring connections shown are for a SNAP-TEX-CBO6 cable. Spring connectors for standard, 4-point ODC modules Module: SNAP-ODC5-i Cable: SNAP-TEX-CBO6 For other module/cable options with this board, see page 2. Field connectors Pins 4-7 to the next ODC module FUSED +24V + + Power Supply 24 VDC + - 24V INPUT Also see next page. SNAP TEX Cables and Breakout Boards Mechanical relays NOTE: Transient protection must be used on inductive loads. Wiring connections shown are for SNAP-TEX-CBO6. One of two spring connectors NOTE: If you are using a SNAP-TEX-CBS6 cable instead of the SNAP-TEX-CBO6, jumpers are required for a SNAP-ODC5-I module. They are not required for a SNAP-ODC5SRC module. Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 25 SNAP TEX Cables and Breakout Boards 4-pt or 16-pt Digital Output Module to SNAP-TEX-MR10-16C SNAP-TEX-MR10-16C Relay Group SNAP TEX Cables and Breakout Boards The diagram below shows relays 0 and 1 in a relay group. NOTE: The diagrams on this page apply to the SNAP-TEX-MR10-16C breakout board used with either a 4-point digital output module or a 16-point digital output module. NOTE: Transient protection must be used on inductive loads. NO DATA SHEET Form 1756-150320 NO NC NC NO NO 0 C 1 NC NC Terminals 0 and 1 Jumper Straps--SNAP-TEX-MR10-16C Breakout Board This diagram shows an example using jumper straps, Opto 22 part numbers STRAP2Q and STRAP4Q. GROUP A COMMON PAGE 26 C Traces on board NO 0 NC C NO 1 NC STRAP4Q NO 2 NC C NO 3 NC NO 4 NC C NO 5 NC NO 6 NC C NO 7 NC GROUP B NO COMMON 8 NC C NO 9 NC NO 10 NC C NO 11 NC NO 12 NC C NO 13 NC NO 14 NC C NO 15 NC STRAP2Q STRAP4Q Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 8-Point Analog Output Module to SNAP-TEX-32 Breakout Board Use up to four 8-point SNAP-AOVA-8 analog output modules per board. Use cable SNAP-HD-20F6. Wiring example for one module is shown below. Black: 24 VDC Excitation (Negative) White with Black: 24 VDC Excitation (Positive) Purple with Yellow (Not used) Yellow with Purple (Not used) SNAP-TEX-32 breakout board 1 Blue 2 White with Blue 3 Pink 4 White with Pink 5 Gray 6 White with Gray 7 Green 8 White with Green 9 Orange 10 White with Orange 11 Red 12 White with Red 13 Purple 14 White with Purple 15 Yellow 16 White with Yellow SNAP TEX Cables and Breakout Boards Cable: SNAP-HD-20F6 Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 27 SNAP TEX Cables and Breakout Boards Wiring: 16-point Digital Module to SNAP-TEX-32 Breakout Board Use two modules per board. The SNAP-HD-ACF6 cable assembly includes two identical cables, each with a 16-pin connector. It takes both cables to cover one module. Wiring for one cable is shown in the diagram below. Field connection wires are twisted pair. Cable: SNAP-HD-ACF6 SNAP TEX Cables and Breakout Boards 16-point module (top view) SNAP-TEX-32 breakout board Red White Black Orange Black Brown Black Yellow Black Blue Black Green Black White Black Red DATA SHEET Form 1756-150320 NOTE: Field wires for the cable are in twisted pairs, so you can see which wires go to each point. PAGE 28 Even though some wire colors repeat, there is no internal connection between points. This module's 16 points are isolated from each other. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 16-point Digital Input Module to SNAP-TEX-FB16-H or SNAP-TEX-FB16-L Resistor LED Blown-fuse LED Fuse Cable: SNAP-HD-ACF6 ACOM Black A0 Red A1 White A2 Green A3 Blue ACOM Black A4 Yellow A5 Brown A6 Orange A7 White Fuse Common Module Common SNAP TEX Cables and Breakout Boards Resistor Fuse BCOM Black B0 Red B1 White B2 Green B3 Blue BCOM Black B4 Yellow Form 1756-150320 B6 Orange B7 White Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET B5 Brown PAGE 29 SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Module to SNAP-TEX-32 Breakout Board SNAP-HD-CBF6 Cable Wiring The following table shows connector wiring for the SNAP-HD-CBF6. Wires from the cable are grouped into four sets. Set A DATA SHEET Form 1756-150320 SNAP TEX Cables and Breakout Boards Wires PAGE 30 Set B Point Wires Set C Point Wires Set D Point Wires Point A0 Gray 0 B0 Gray 8 C0 Gray 16 D0 Gray 24 A1 Blue 1 B1 Blue 9 C1 Blue 17 D1 Blue 25 A2 Yellow 2 B2 Yellow 10 C2 Yellow 18 D2 Yellow 26 A3 Red 3 B3 Red 11 C3 Red 19 D3 Red 27 A4 White 4 B4 White 12 C4 White 20 D4 White 28 A5 Violet 5 B5 Violet 13 C5 Violet 21 D5 Violet 29 A6 Green 6 B6 Green 14 C6 Green 22 D6 Green 30 A7 Orange 7 B7 Orange 15 C7 Orange 23 D7 Orange 31 ACOM Blk/Brn com BCOM Blk/Brn com CCOM Blk/Brn com DCOM Blk/Brn com The four sets relate to point numbers on the module as shown below. Harness Pin Wire Color Number Gray 40 Blue 38 Yellow 36 Red 34 Black 32 Gray 30 Blue 28 Yellow 26 Red 24 Black 22 Gray 20 Blue 18 Yellow 16 Red 14 Black 12 Gray 10 Blue 8 Yellow 6 Red 4 Black 2 Signal A0 A1 A2 A3 ACOM B0 B1 B2 B3 BCOM C0 C1 C2 C3 CCOM D0 D1 D2 D3 DCOM Signal A4 A5 A6 A7 ACOM B4 B5 B6 B7 BCOM C4 C5 C6 C7 CCOM D4 D5 D6 D7 DCOM Pin Number 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 Harness Wire Color White Violet Green Orange Brown White Violet Green Orange Brown White Violet Green Orange Brown White Violet Green Orange Brown Connector wiring for SNAP-ODC-32-SNK, SNAP-ODC-32-SRC, SNAP-IDC-32, -FM versions, SNAP-IDC-32N, and SNAP-IDC-32DN (top view of module) Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Output Module to SNAP-TEX-FB16-H or SNAP-TEX-FB16-L From SNAP-ODC-32-SRC or SNAP-ODC-32-SNK digital output module. Use two boards per module. Resistor Fuse Blown-fuse LED See tables on page 30. LED Fuse Cable: SNAP-HD-CBF6 ACOM Black A0 Gray A1 Blue A2 Yellow A3 Red ACOM Brown A4 White A5 Violet A6 Green A7 Orange Fuse Common Module Common BCOM Black B0 Gray For SRC module, module common is positive, and field commons (1, 3, 5, and 7) are negative. SNAP TEX Cables and Breakout Boards Resistor B1 Blue B2 Yellow For SNK module, module common is negative, and field commons (1, 3, 5, and 7) are positive. B3 Red BCOM Brown B4 White Form 1756-150320 B6 Green B7 Orange Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET B5 Violet PAGE 31 SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Input Module to SNAP-IDC-HDB Board For more information, see the SNAP High-Density Digital Modules User's Guide, form 1547. SNAP TEX Cables and Breakout Boards JP-D JP-C JP-B JP-A X X X X Z Z Z Z Set jumpers to the X position for all input modules. There is one power status LED for each zone of 8 signal inputs (4 power LEDs total). There is one LED for each signal input (32 signal LEDs total) SNAP-IDC-32 (or -FM) or SNAP-IDC-32D - + Connect the negative lead (-) from the power supply to one Module COM terminal. Connect the positive lead (+) to one Field COM terminal. Module Field COM COM SNAP-IDC-32N or SNAP-IDC-32DN + - DATA SHEET Form 1756-150320 - PAGE 32 Connect the positive lead (+) from the power supply to one Module COM terminal. Connect the negative lead (-) to one Field COM terminal. Module Field COM COM + Signal shown is for SNAP-IDC-32 and -FM and SNAP-IDC-32D. Signal reverses for SNAP-IDC-32N and -32DN. Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards 32-point Digital Input Module to SNAP-IDC-HDB (continued) Modules--this diagram applies to: SNAP-IDC-32 SNAP-IDC-32-FM SNAP-IDC-32N SNAP TEX Cables and Breakout Boards IMPORTANT: All SNAP-IDC-32 modules are polarity specific and must be wired as shown. Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 33 SNAP TEX Cables and Breakout Boards 32-point Digital Input Module to SNAP-IDC-HDB (continued) DATA SHEET IMPORTANT: All SNAP-IDC-32 modules are polarity specific and must be wired as shown. Form 1756-150320 SNAP TEX Cables and Breakout Boards Modules--this diagram applies to: SNAP-IDC-32-D SNAP-IDC-32-DN PAGE 34 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Output Module to SNAP-ODC-HDB Board For more information, see the SNAP High-Density Digital Modules User's Guide, form 1547. JP-D JP-C X Z Z Set jumpers to the Z position. Power Supply Connections JP-A X X Z Z SNAP-ODC-32-SRC (or -FM) + - SNAP TEX Cables and Breakout Boards X JP-B Connect the positive lead (+) from the power supply to one Module COM terminal. Connect the negative lead (-) to one Field COM terminal. Module Field COM COM SNAP-ODC-32-SNK (or -FM) - + Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. Form 1756-150320 Module Field COM COM DATA SHEET Connect the negative lead (-) from the power supply to one Module COM terminal. Connect the positive lead (+) to one Field COM terminal. PAGE 35 SNAP TEX Cables and Breakout Boards 32-point Digital Output Module to SNAP-ODC-HDB (continued) Field Connections Nominal 12-24 VDC Typical for sourcing DATA SHEET Form 1756-150320 SNAP TEX Cables and Breakout Boards Typical for sinking PAGE 36 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards 32-point Digital Output Module to SNAP-ODC-HDB (continued) FUSING LO LO LO + LO LO LO LO LO LO LO + LO LO LO + LO LO LO + LO A5 LO A2 A6 A3 A7 B0 LO B1 LO B2 LO B3 LO + LO LO B5 LO B6 B7 LO LO LO LO C0 LO + LO LO C1 C5 LO C2 C6 LO C3 + LO CCOM LO LO LO LO D0 LO D1 D5 LO D2 D6 LO D3 + LO DCOM 12-24 VDC Nominal LO LO A0 A4 A1 A5 A2 A6 A3 A7 ACOM LO B0 LO B1 LO B2 LO B3 B4 B5 B6 B7 BCOM LO LO LO LO C0 C4 C1 C5 C2 C6 C3 C7 CCOM 12-24 VDC Nominal D4 D7 LO 12-24 VDC Nominal C4 C7 LO 12-24 VDC Nominal B4 BCOM 12-24 VDC Nominal LO LO A1 LO 12-24 VDC Nominal LO A4 ACOM 12-24 VDC Nominal LO A0 LO LO LO LO D0 D4 D1 D5 D2 SNAP TEX Cables and Breakout Boards For both sourcing and sinking modules, either fuse each point (as shown in the first and third groups, below) or fuse each group of points (as shown in the second and fourth groups). D6 D3 D7 DCOM 12-24 VDC Nominal SNAP-ODC-32-SRC Load Sourcing Module (Top view of module) SNAP-ODC-32-SNK Load Sinking Module (Top view of module) Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 37 SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Output Module to SNAP-TEX-MR10-16 Board SNAP-TEX-MR10-16 breakout board Two breakout boards are required for the 32 points on the module. - + 24VDC SNAP TEX Cables and Breakout Boards For 32-point sourcing modules only (SNAP-ODC-32-SRC or SNAP-ODC-32-SRC-FM). Use two breakout boards with one module and one SNAP-HD-CBF6 cable. Black Brown Black Brown Fused 24 VDC Blown fuse LED Cable: SNAP-HD-CBF6 16 Orange 15 Green 14 Violet From SNAP-ODC-32SRC module 13 White 12 Red 11 Yellow 10 Blue 9 Gray 8 Orange 7 Green 6 Violet Field wiring--For normally open (N.O.) or normally closed (N.C.). 5 White 4 Red 3 Yellow 2 Blue 1 Gray DATA SHEET Form 1756-150320 Wire the other I/O points to a second breakout board. PAGE 38 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 32-point Digital Output Module to SNAP-TEX-MR10-16C Board For 32-point sourcing modules only (SNAP-ODC-32-SRC or SNAP-ODC-32-SRC-FM). Use two breakout boards with one module and one SNAP-HD-G4F6 cable (each cable has two header connectors). Mechanical relays Header connector for 32-point SNAP-ODC-32-SRC module Field connectors SNAP-TEX-MR10-16C breakout boards Two breakout boards are required for the 32 points on the module. Brown SNAP-ODC-32-SRC module Cable: SNAP-HD-G4F6 Brown Pin 1 SNAP TEX Cables and Breakout Boards Pin 1 for header connector NOTE: If there is a mismatch between the cable connector and the header connector, please contact Opto 22 Product Support. Form 1756-150320 (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com PAGE 39 SNAP TEX Cables and Breakout Boards Wiring: 32-point Analog Current Module to SNAP-AIMA-HDB Board This diagram cannot be used with self-sourcing transmitters. Use this diagram only with loop power (2-wire) negative common devices. For self-powered (4-wire) devices, use a SNAP-AIV-HDB board and the wiring diagram on page 41 (for negative common devices) or page 42 (for positive common devices). SNAP-AIMA-HDB breakout board DATA SHEET Cable: SNAP-HD-BF6 Form 1756-150320 SNAP TEX Cables and Breakout Boards See "Working with Module Values" on page 17. PAGE 40 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. SNAP TEX Cables and Breakout Boards Wiring: 32-point Analog Module to SNAP-AIV-HDB Breakout Board Self-powered devices with negative common Use this diagram for a SNAP-AIV-32 module or for a SNAP-AIMA-32 module when the module connects to self-powered (4-wire) devices that share a negative common connection. See the module's data sheet for more information. See "Working with Module Values" on page 17. SNAP-AIV-HDB breakout board Cable: SNAP-HD-BF6 SNAP TEX Cables and Breakout Boards * * Form 1756-150320 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. DATA SHEET * Or 4-wire, 4-20 mA transmitter, if using a SNAPAIMA-32 or SNAP-AIMA-32-FM module with this rack PAGE 41 SNAP TEX Cables and Breakout Boards Wiring: 32-point Analog Module to SNAP-AIV-HDB Breakout Board Self-powered devices with positive common SNAP-AIV-HDB breakout board DATA SHEET See "Working with Module Values" on page 17. Cable: SNAP-HD-BF6 Form 1756-150320 SNAP TEX Cables and Breakout Boards Use this diagram for a SNAP-AIV-32 module or a SNAP-AIMA-32 module when the module connects to self-powered (4-wire) devices that share a positive common connection. See the module's data sheet for more information. PAGE 42 Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * www.opto22.com SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2008-2015 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations. More About Opto 22 Products Opto 22 develops and manufactures reliable, flexible, easy-to-use hardware and software products for industrial automation, energy management, remote monitoring, and data acquisition applications. groov groov puts your system on your mobile device. With zero programming, you can build mobile operator interfaces to monitor and control systems from Allen-Bradley, Siemens, Schneider Electric, Modicon, and many more. Web-based groov puts mobile-ready gadgets at your fingertips. Tag them from your existing tag database, and they automatically scale for use on any device with a modern web browser. See groov.com for more information and your free trial. SNAP PAC System Designed to simplify the typically complex process of selecting and applying an automation system, the SNAP PAC System consists of four integrated components: * SNAP PAC controllers * PAC ProjectTM Software Suite * SNAP PAC brains * SNAP I/OTM SNAP PAC Controllers Programmable automation controllers (PACs) are multifunctional, modular controllers based on open standards. Opto 22 has been manufacturing PACs for over two decades. The standalone SNAP PAC S-series, the rack-mounted SNAP PAC Rseries, and the software-based SoftPACTM all handle a wide range of digital, analog, and serial functions for data collection, remote monitoring, process control, and discrete and hybrid manufacturing. SNAP PACs are based on open Ethernet and Internet Protocol (IP) standards, so you can build or extend a system easily, without the expense and limitations of proprietary networks and protocols. Wired+WirelessTM models are also available. PAC Project Software Suite Opto 22's PAC Project Software Suite provides full-featured, costeffective control programming, HMI (human machine interface) development and runtime, OPC server, and database connectivity software for your SNAP PAC System. Control programming includes both easy-to-learn flowcharts and optional scripting. Commands are in plain English; variables and I/ O point names are fully descriptive. PAC Project Basic offers control and HMI tools and is free for download on our website, www.opto22.com. PAC Project Professional, available for separate purchase, adds one SoftPAC, OptoOPCServer, OptoDataLink, options for controller redundancy or segmented networking, and support for legacy Opto 22 serial misticTM I/O units. SNAP PAC Brains While SNAP PAC controllers provide central control and data distribution, SNAP PAC brains provide distributed intelligence for I/O processing and communications. Brains offer analog, digital, and serial functions, including thermocouple linearization; PID loop control; and optional high-speed digital counting (up to 20 kHz), quadrature counting, TPO, and pulse generation and measurement. SNAP I/O I/O provides the local connection to sensors and equipment. Opto 22 SNAP I/O offers 1 to 32 points of reliable I/O per module, depending on the type of module and your needs. Analog, digital, and serial modules are all mixed on the same mounting rack and controlled by the same processor (SNAP PAC brain or rack-mounted controller). Quality Founded in 1974, Opto 22 has established a worldwide reputation for high-quality products. All are made in the U.S.A. at our manufacturing facility in Temecula, California. Because we test each product twice before it leaves our factory, rather than only testing a sample of each batch, we can guarantee most solid-state relays and optically isolated I/O modules for life. Free Product Support Opto 22's California-based Product Support Group offers free, comprehensive technical support for Opto 22 products. Our staff of support engineers represents decades of training and experience. Support is available in English and Spanish by phone or email, Monday-Friday, 7 a.m. to 5 p.m. PST. Additional support is always available on our website: how-to videos, OptoKnowledgeBase, self-training guide, troubleshooting and user's guides, and OptoForums. In addition, hands-on training is available for free at our Temecula, California headquarters, and you can register online. Purchasing Opto 22 Products Opto 22 products are sold directly and through a worldwide network of distributors, partners, and system integrators. For more information, contact Opto 22 headquarters at 800-3216786 or 951-695-3000, or visit our website at www.opto22.com. www.opto22.com www.opto22.com * Opto 22 * 43044 Business Park Drive * Temecula, CA 92590-3614 * Form 1335-131203 SALES 800-321-6786 * 951-695-3000 * FAX 951-695-3095 * sales@opto22.com * SUPPORT 800-835-6786 * 951-695-3080 * FAX 951-695-3017 * support@opto22.com (c) 2014 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.