OPA365 OPA2365 SBOS365D - JUNE 2006 - REVISED JUNE 2009 50MHz, Low-Distortion, High CMRR, RRI/O, Single-Supply OPERATIONAL AMPLIFIER FEATURES DESCRIPTION D GAIN BANDWIDTH: 50MHz D ZERO-CROSSOVER DISTORTION TOPOLOGY: The OPAx365 zer-crossover series, rail-to-rail, highperformance, CMOS operational amplifiers are optimized for very low voltage, single-supply applications. Rail-to-rail input/output, low-noise (4.5nV/Hz) and high-speed operation (50MHz Gain Bandwidth) make these devices ideal for driving sampling analog-to-digital converters (ADCs). Applications incude audio, signal conditioning, and sensor amplification. The OPA365 family of op amps are also well-suited for cell phone power amplifier control loops. - Excellent THD+N: 0.0004% - CMRR: 100dB (min) - Rail-to-Rail Input and Output - Input 100mV Beyond Supply Rail D D D D D LOW NOISE: 4.5nV//Hz at 100kHz SLEW RATE: 25V/s FAST SETTLING: 0.3s to 0.01% PRECISION: - Low Offset: 100V - Low Input Bias Current: 0.2pA 2.2V TO 5.5V OPERATION Special features include an excellent common-mode rejection ratio (CMRR), no input stage crossover distortion, high input impedance, and rail-to-rail input and output swing. The input common-mode range includes both the negative and positive supplies. The output voltage swing is within 10mV of the rails. APPLICATIONS D D D D D D D The OPA365 (single version) is available in the microSIZE SOT23-5 and SO-8 packages. The OPA2365 (dual version) is offered in the SO-8 package. All versions are specified for operation from -40C to +125C. Single and dual versions have identical specifications for maximum design flexibility. SIGNAL CONDITIONING DATA ACQUISITION PROCESS CONTROL ACTIVE FILTERS TEST EQUIPMENT AUDIO WIDEBAND AMPLIFIERS R2 2k C2 2.2pF V- V- U1 U2 SD1 BAT17 OPA365 VOUT OPA365 R1 7.5 VIN V+ C1 10nF V+ Fast Settling Peak Detector Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright 2006-2009, Texas Instruments Incorporated ! ! www.ti.com "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5.5V Signal Input Terminals, Voltage(2) . . . . (V-) -0.5V to (V+) + 0.5V Signal Input Terminals, Current(2) . . . . . . . . . . . . . . . . . . . . 10mA Output Short-Circuit(3) . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Operating Temperature . . . . . . . . . . . . . . . . . . . . . -40C to +150C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150C ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4000V Charged Device Model . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000V Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400V (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not supported. (2) Input terminals are diode-clamped to the power-supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be current limited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR SOT23-5 DBV OAVQ SO-8 D O365A OPA365 PACKAGE MARKING OPA2365 SO-8 D O2365A (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. PIN CONFIGURATIONS Top View OPA365 OPA365 VOUT 1 V- 2 +IN 3 5 4 V+ -IN OPA2365 NC(1) 1 8 NC(1) -IN 2 7 +IN 3 V- 4 VOUTA 1 8 V+ V+ -IN A 2 7 VOUTB 6 VOUT +IN A 3 6 -IN B 5 NC(1) V- 4 5 +IN B SOT23-5 SO-8 (1) NC denotes no internal connection. 2 SO-8 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 ELECTRICAL CHARACTERISTICS: VS = +2.2V to +5.5V Boldface limits apply over the specified temperature range, TA = -40C to +125C. At TA = +25C, RL = 10k connected to VS/2, VCM = VS/2, and VOUT = VS/2, unless otherwise noted. OPAx365 PARAMETER OFFSET VOLTAGE Input Offset Voltage VOS Drift dVOS/dT vs Power Supply PSRR Channel Separation, dc INPUT BIAS CURRENT Input Bias Current IB over Temperature Input Offset Current IOS NOISE Input Voltage Noise, f = 0.1Hz to 10Hz en Input Voltage Noise Density, f = 100kHz en Input Current Noise Density, f = 10kHz in INPUT VOLTAGE RANGE Common-Mode Voltage Range VCM Common-Mode Rejection Ratio CMRR INPUT CAPACITANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain AOL FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise(1) OUTPUT Voltage Output Swing from Rail over Temperature Short-Circuit Current Capacitive Load Drive Open-Loop Output Impedance POWER SUPPLY Specified Voltage Range Quiescent Current Per Amplifier over Temperature TEMPERATURE RANGE Specified Range Thermal Resistance SOT23-5 SO-8 GBW SR tS THD+N TEST CONDITIONS VS = +2.2V to +5.5V TYP MAX UNIT 100 1 10 0.2 200 V V/C V/V V/V 100 0.2 10 See Typical Characteristics 0.2 10 (V-) - 0.1V 3 VCM 3 (V+) + 0.1V RL = 10k, 100mV < VO < (V+) - 100mV RL = 600, 200mV < VO < (V+) - 200mV RL = 600, 200mV < VO < (V+) - 200mV VS = 5V (V-) - 0.1 100 100 100 94 G = +1 4V Step, G = +1 4V Step, G = +1 VIN x Gain > VS RL = 600, VO = 4VPP, G = +1, f = 1kHz RL = 10k, VS = 5.5V f = 1MHz, IO = 0 pA 120 (V+) + 0.1 V dB 6 2 pF pF 120 120 dB dB dB 50 25 200 300 < 0.1 0.0004 MHz V/s ns ns s % 10 20 65 See Typical Characteristics 30 2.2 IO = 0 pA VPP nV/Hz fA/Hz 5 4.5 4 ISC CL VS IQ MIN 4.6 -40 qJA 200 150 mV mA 5.5 5 5 V mA mA +125 C C/W C/W C/W (1) 3rd-order filter; bandwidth 80kHz at -3dB. 3 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 TYPICAL CHARACTERISTICS At TA = +25C, VS = +5V, and CL = 0pF, unless otherwise noted. POWER SUPPLY AND COMMON-MODE REJECTION RATIO vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 140 0 140 CMRR -45 100 Phase 80 -90 60 40 Gain 20 -135 PSRR, CMRR (dB) 120 Phase (_ ) Voltage Gain (dB) 120 100 80 PSRR 60 40 20 0 -180 100M -20 10 100 1k 10k 100k 1M 10M 0 10 100 1k 10k 100k 1M Frequency (Hz) Frequency (Hz) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 10M 100M 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -200 -180 -160 -140 -120 -100 -80 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 200 Population Population VS = 5.5V Offset Voltage Drift (V/_ C) Offset Voltage (V) INPUT BIAS CURRENT vs TEMPERATURE INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE 500 1000 900 400 700 300 600 IB (pA) Input Bias (pA) 800 500 400 VCM Specified Range 300 100 200 100 0 -50 -25 0 25 50 Temperature (_C) 4 200 75 100 125 0 -25 -0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 VCM (V) "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 TYPICAL CHARACTERISTICS (continued) At TA = +25C, VS = +5V, and CL = 0pF, unless otherwise noted. OPA365 OUTPUT VOLTAGE vs OUTPUT CURRENT 3 3 VS = 1.1V VS = 2.75V 1 -40_ C 0 +25_ C +125_C +25_ C VS = 1.1V VS = 2.75V 2 Output Voltage (V) 2 Output Voltage (V) OPA2365 OUTPUT VOLTAGE SWING vs OUTPUT CURRENT -40_ C +125_ C -1 -2 1 +25_ C 0 +125_C +25_C -40_C -1 -3 0 10 20 30 40 50 60 70 80 90 100 0 10 20 30 Output Current (mA) 40 50 60 70 80 90 100 Output Current (mA) SHORT-CIRCUIT CURRENT vs TEMPERATURE QUIESCENT CURRENT vs SUPPLY VOLTAGE 4.75 Dual Quiescent Current (mA) Short-Circuit Current (mA) +125_ C -2 -3 70 60 50 40 30 20 10 0 -10 -20 -30 -40 -50 -60 -70 -80 -40_C Single VS = 2.75V 4.50 4.25 4.00 3.75 -50 -25 0 25 50 75 100 125 2.2 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Supply Voltage (V) Temperature (_ C) 0.1Hz to 10Hz INPUT VOLTAGE NOISE QUIESCENT CURRENT vs TEMPERATURE 4.74 4.68 2V/div Quiescent Current (mA) 4.80 4.62 4.56 4.50 -50 -25 0 25 50 75 100 125 1s/div Temperature (_ C) 5 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 TYPICAL CHARACTERISTICS (continued) At TA = +25C, VS = +5V, and CL = 0pF, unless otherwise noted. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY INPUT VOLTAGE NOISE SPECTRAL DENSITY 1k 0.01 VO = 1VRMS 0.001 Voltage Noise (nV/Hz) THD+N (%) G = 10, RL = 600 VO = 1.448VRMS 100 10 VO = 1VRMS G = +1, RL = 600 1 0.0001 10 100 1k 10k 10 20k 100 1k 10k Frequency (Hz) Frequency (Hz) OVERSHOOT vs CAPACITIVE LOAD 60 SMALL-SIGNAL STEP RESPONSE G = +1 Output Voltage (50mV/div) Overshoot (%) 50 40 G = -1 30 G = +10 20 10 G = -10 G=1 RL = 10k VS = 2.5 0 0 100 1k Capacitive Load (pF) Time (50ns/div) SMALL-SIGNAL STEP RESPONSE Output Voltage (50mV/div) Output Voltage (1V/div) LARGE-SIGNAL STEP RESPONSE G=1 RL = 10k VS = 2.5 Time (250ns/div) 6 G=1 RL = 600 VS = 2.5 Time (50ns/div) 100k "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 TYPICAL CHARACTERISTICS (continued) At TA = +25C, VS = +5V, and CL = 0pF, unless otherwise noted. Output Voltage (1V/div) LARGE-SIGNAL STEP RESPONSE G=1 RL = 600 VS = 2.5 Time (250ns/div) 7 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 APPLICATIONS INFORMATION R2 10k OPERATING CHARACTERISTICS The OPA365 amplifier parameters are fully specified from +2.2V to +5.5V. Many of the specifications apply from -40C to +125C. Parameters that can exhibit significant variance with regard to operating voltage or temperature are presented in the Typical Characteristics. +1.5V R1 1k V+ OPA365 GENERAL LAYOUT GUIDELINES The OPA365 is a wideband amplifier. To realize the full operational performance of the device, good high-frequency printed circuit board (PCB) layout practices are required. Low-loss, 0.1F bypass capacitors must be connected between each supply pin and ground as close to the device as possible. The bypass capacitor traces should be designed for minimum inductance. C1 100nF VIN V- C2 100nF -1.5V a) Dual Supply Connection BASIC AMPLIFIER CONFIGURATIONS As with other single-supply op amps, the OPA365 may be operated with either a single supply or dual supplies. A typical dual-supply connection is shown in Figure 1, which is accompanied by a single-supply connection. The OPA365 is configured as a basic inverting amplifier with a gain of -10V/V. The dual-supply connection has an output voltage centered on zero, while the single- supply connection has an output centered on the common-mode voltage VCM. For the circuit shown, this voltage is 1.5V, but may be any value within the commonmode input voltage range. The OPA365 VCM range extends 100mV beyond the power-supply rails. VOUT R2 10k +3V R1 1k C1 100nF V+ OPA365 VIN V- VCM = 1.5V b) Single-Supply Connection Figure 1. Basic Circuit Connections 8 VOUT "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 Figure 2 shows a single-supply, electret microphone application where VCM is provided by a resistive divider. The divider also provides the bias voltage for the electret element. 49k Clean 3.3V Supply 3.3V 4k INPUT AND ESD PROTECTION The OPA365 incorporates internal electrostatic discharge (ESD) protection circuits on all pins. In the case of input and output pins, this protection primarily consists of current steering diodes connected between the input and power-supply pins. These ESD protection diodes also provide in-circuit, input overdrive protection, provided that the current is limited to 10mA as stated in the Absolute Maximum Ratings. Figure 3 shows how a series input resistor may be added to the driven input to limit the input current. The added resistor contributes thermal noise at the amplifier input and its value should be kept to the minimum in noise-sensitive applications. VOUT OPA365 Electret Microphone 6k 5k 1F Figure 2. Microphone Preamplifier V+ RAIL-TO-RAIL INPUT I OVERLOAD 10mA max The OPA365 product family features true rail-to-rail input operation, with supply voltages as low as 1.1V (2.2V). A unique zer-crossover input topology eliminates the input offset transition region typical of many rail-to-rail, complementary stage operational amplifiers. This topology also allows the OPA365 to provide superior common-mode performance over the entire input range, which extends 100mV beyond both power-supply rails, as shown in Figure 4. When driving ADCs, the highly linear VCM range of the OPA365 assures that the op amp/ADC system linearity performance is not compromised. VOUT OPA365 VIN 5k Figure 3. Input Current Protection OFFSET VOLTAGE vs COMMON-MODE VOLTAGE 200 VS = 2.75V 150 100 VOS (V) OPA365 50 0 -50 -100 Competitors -150 -200 -3 -2 -1 0 1 2 3 Common-Mode Voltage (V) Figure 4. OPA365 has Linear Offset Over the Entire Common-Mode Range 9 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 A simplified schematic illustrating the rail-to-rail input circuitry is shown in Figure 5. VS Regulated Charge Pump VO U T = VC C +1.8V CAPACITIVE LOADS The OPA365 may be used in applications where driving a capacitive load is required. As with all op amps, there may be specific instances where the OPA365 can become unstable, leading to oscillation. The particular op amp circuit configuration, layout, gain and output loading are some of the factors to consider when establishing whether an amplifier will be stable in operation. An op amp in the unity-gain (+1V/V) buffer configuration and driving a capacitive load exhibits a greater tendency to be unstable than an amplifier operated at a higher noise gain. The capacitive load, in conjunction with the op amp output resistance, creates a pole within the feedback loop that degrades the phase margin. The degradation of the phase margin increases as the capacitive loading increases. VC C + 1.8V Patent Pending Very Low Ripple Topology IB IAS IB IA S IBI A S VIN - VO U T VI N + When operating in the unity-gain configuration, the OPA365 remains stable with a pure capacitive load up to approximately 1nF. The equivalent series resistance (ESR) of some very large capacitors (CL > 1F) is sufficient to alter the phase characteristics in the feedback loop such that the amplifier remains stable. Increasing the amplifier closed-loop gain allows the amplifier to drive increasingly larger capacitance. This increased capability is evident when observing the overshoot response of the amplifier at higher voltage gains. See the typical characteristic graph, Small-Signal Overshoot vs. Capacitive Load. One technique for increasing the capacitive load drive capability of the amplifier operating in unity gain is to insert a small resistor, typically 10 to 20, in series with the output; see Figure 6. This resistor significantly reduces the overshoot and ringing associated with large capacitive loads. A possible problem with this technique is that a voltage divider is created with the added series resistor and any resistor connected in parallel with the capacitive load. The voltage divider introduces a gain error at the output that reduces the output swing. The error contributed by the voltage divider may be insignificant. For instance, with a load resistance, RL = 10k, and RS = 20, the gain error is only about 0.2%. However, when RL is decreased to 600, which the OPA365 is able to drive, the error increases to 7.5%. 10 IB IA S Figure 5. Simplified Schematic V+ RS VOUT OPA365 VIN 10 to 20 RL CL Figure 6. Improving Capacitive Load Drive "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 ACHIEVING AN OUTPUT LEVEL OF ZERO VOLTS (0V) V+ = +5V Certain single-supply applications require the op amp output to swing from 0V to a positive full-scale voltage and have high accuracy. An example is an op amp employed to drive a single-supply ADC having an input range from 0V to +5V. Rail-to-rail output amplifiers with very light output loading may achieve an output level within millivolts of 0V (or +VS at the high end), but not 0V. Furthermore, the deviation from 0V only becomes greater as the load current required increases. This increased deviation is a result of limitations of the CMOS output stage. OPA365 500A Note that this technique does not work with all op amps and should only be applied to op amps such as the OPA365 that have been specifically designed to operate in this manner. Also, operating the OPA365 output at 0V changes the output stage operating conditions, resulting in somewhat lower open-loop gain and bandwidth. Keep these precautions in mind when driving a capacitive load because these conditions can affect circuit transient response and stability. RP = 10k Op Amps Negative Supply Grounded When a pull-down resistor is connected from the amplifier output to a negative voltage source, the OPA365 can achieve an output level of 0V, and even a few millivolts below 0V. Below this limit, nonlinearity and limiting conditions become evident. Figure 7 illustrates a circuit using this technique. A pull-down current of approximately 500A is required when OPA365 is connected as a unity-gain buffer. A practical termination voltage (VNEG) is -5V, but other convenient negative voltages also may be used. The pull-down resistor RL is calculated from RL = [(VO -VNEG)/(500A)]. Using a minimum output voltage (VO) of 0V, RL = [0V-(-5V)]/(500A)] = 10k. Keep in mind that lower termination voltages result in smaller pull-down resistors that load the output during positive output voltage excursions. VOUT VIN -V = -5V (Additional Negative Supply) Figure 7. Swing-to-Ground R3 549 C2 150pF V+ R1 549 R2 1.24k VIN OPA365 C1 1nF VOUT V- Figure 8. Second-Order Butterworth 500kHz Low-Pass Filter ACTIVE FILTERING The OPA365 is well-suited for active filter applications requiring a wide bandwidth, fast slew rate, low-noise, single-supply operational amplifier. Figure 8 shows a 500kHz, 2nd-order, low-pass filter utilizing the multiple- feedback (MFB) topology. The components have been selected to provide a maximally-flat Butterworth response. Beyond the cutoff frequency, roll-off is -40dB/dec. The Butterworth response is ideal for applications requiring predictable gain characteristics such as the anti-aliasing filter used ahead of an ADC. 11 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 One point to observe when considering the MFB filter is that the output is inverted, relative to the input. If this inversion is not required, or not desired, a noninverting output can be achieved through one of these options: 1) adding an inverting amplifier; 2) adding an additional 2nd-order MFB stage; or 3) using a noninverting filter topology such as the Sallen-Key (shown in Figure 9). MFB and Sallen-Key, low-pass and high-pass filter synthesis is quickly accomplished using TI's FilterPro program. This software is available as a free download at www.ti.com. DRIVING AN ANALOG-TO-DIGITAL CONVERTER Very wide common-mode input range, rail-to-rail input and output voltage capability and high speed make the OPA365 an ideal driver for modern ADCs. Also, because it is free of the input offset transition characteristics inherent to some rail-to-rail CMOS op amps, the OPA365 provides low THD and excellent linearity throughout the input voltage swing range. Figure 10 shows the OPA365 driving an ADS8326, 16-bit, 250kSPS converter. The amplifier is connected as a unity-gain, noninverting buffer and has an output swing to 0V, making it directly compatible with the ADC minus full-scale input level. The 0V level is achieved by powering the OPA365 V- pin with a small negative voltage established by the diode forward voltage drop. A small, signal-switching diode or Schottky diode provides a suitable negative supply voltage of -0.3 to -0.7V. The supply rail-to-rail is equal to V+, plus the small negative voltage. C3 220pF R2 19.5k R1 1.8k R3 150k VIN = 1VRMS C1 3.3nF C2 47pF OPA365 VOUT Figure 9. Configured as a 3-Pole, 20kHz, Sallen-Key Filter +5V C1 100nF +5V R1(1) 100 V+ +IN OPA365 C3(1) 1nF V- VIN 0 to 4.096V -IN ADS8326 16-Bit 250kSPS REF IN +5V Optional(2) R2 500 SD1 BAS40 -5V C2 100nF REF3240 4.096V C4 100nF NOTES: (1) Suggested value; may require adjustment based on specific application. (2) Single-supply applications lose a small number of ADC codes near ground due to op amp output swing limitation. If a negative power supply is available, this simple circuit creates a -0.3V supply to allow output swing to true ground potential. Figure 10. Driving the ADS8326 12 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 One method for driving an ADC that negates the need for an output swing down to 0V uses a slightly compressed ADC full-scale input range (FSR). For example, the 16-bit ADS8361 (shown in Figure 11) has a maximum FSR of 0V to 5V, when powered by a +5V supply and VREF of 2.5V. The idea is to match the ADC input range with the op amp full linear output swing range; for example, an output range of +0.1 to +4.9V. The reference output from the ADS8361 ADC is divided down from 2.5V to 2.4V using a resistive divider. The ADC FSR then becomes 4.8VPP centered on a common-mode voltage of +2.5V. Current from the ADS8361 reference pin is limited to about 10A. Here, 5A was used to bias the divider. The resistors must be precise to maintain the ADC gain accuracy. An additional benefit of this method is the elimination of the negative supply voltage; it requires no additional power-supply current. An RC network, consisting of R1 and C1, is included between the op amp and the ADS8361. It not only provides a high-frequency filter function, but more importantly serves as a charge reservoir used for charging the converter internal hold capacitance. This capability assures that the op amp output linearity is maintained as the ADC input characteristics change throughout the conversion cycle. Depending on the particular application and ADC, some optimization of the R1 and C1 values may be required for best transient performance. R2 10k +5V R1 10k C1 100nF V+ +5V R3(1) 100 -IN OPA365 VIN 0.1V to 4.9V C2(1) V- 1nF +IN ADS8361 16-Bit 100kSPS REF OUT REF IN +2.5V NOTE: (1) Suggested value; may require adjustment based on specific application. R4 20k +2.4V R5 480k C3 1F Figure 11. Driving the ADS8361 13 "#$ %"#$ www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 Figure 12 illustrates the OPA2365 dual op amp providing signal conditioning within an ADS1258 bridge sensor circuit. It follows the ADS1258 16:1 multiplexer and is connected as a differential in/differential out amplifier. The voltage gain for this stage is approximately 10V/V. Driving the ADS1258 internal ADC in differential mode, rather than in a single-ended, exploits the full linearity performance capability of the converter. For best common-mode rejection the two R2 resistors should be closely matched. Note that in Figure 12, the amplifiers, bridges, ADS1258 and internal reference are powered by the same single +5V supply. This ratiometric connection helps cancel excitation voltage drift effects and noise. For best performance, the +5V supply should be as free as possible of noise and transients. When the ADS1258 data rate is set to maximum and the chop feature enabled, this circuit yields 12 bits of noise-free resolution with a 50mV full-scale input. The chop feature is used to reduce the ADS1258 offset and offset drift to very low levels. A 2.2nF capacitor is required across the ADC inputs to bypass the sampling currents. The 47 resistors provide isolation for the OPA2365 outputs from the relatively large, 2.2nF capacitive load. For more information regarding the ADS1258, see the product data sheet available for down load at www.ti.com. +5V RFI 10F + 0.1F 2k RFI AIN0 AVSS AVDD 2k REFP AIN1 + ... 2k RFI AINCOM MUXOUTP AIN15 MUXOUTN 2k RFI ADS1258 AIN14 RFI ADCINN ... ... REFN ADCINP RFI +5V 2.2nF 0.1F R3 47 OPA2365 R2 = 10k R1 = 2.2k R2 = 10k R3 47 OPA2365 NOTE: G = 1 + 2R2/R1. Match R2 resistors for optimum CMRR. Figure 12. Conditioning Input Signals to the ADS1258 on a Single-Supply 14 10F 0.1F www.ti.com SBOS365D - JUNE 2006 - REVISED JUNE 2009 Revision History DATE REV PAGE SECTION DESCRIPTION Changed title. Changed feature bullets. 6/09 D 1 Front Page Changed drawing. Deleted table. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. 15 PACKAGE OPTION ADDENDUM www.ti.com 3-Jun-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp OPA2365AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2365AIDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2365AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA2365AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDBVRG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDBVTG4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM OPA365AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 3-Jun-2011 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF OPA365 : * Automotive: OPA365-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2365AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 OPA365AIDBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 OPA365AIDBVR SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 OPA365AIDBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 OPA365AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2365AIDR SOIC D 8 2500 367.0 367.0 35.0 OPA365AIDBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 OPA365AIDBVR SOT-23 DBV 5 3000 203.0 203.0 35.0 OPA365AIDBVT SOT-23 DBV 5 250 180.0 180.0 18.0 OPA365AIDR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated