DataSheet
Panel Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2018 Crydom Inc. Specifications subject to change without notice.
FDE-07-01 REV. A
DUAL Series
• Independently controlled dual output solid-state relay
• Ratings from 25A to 40A @ 24-530 VAC
• Industry standard package
• SCR output for heavy industrial loads
• DC Control
• Zero-crossing (resistive loads) or random-fire (inductive loads) output
PRODUCT SELECTION
AVAILABLE OPTIONS
Control Voltage
4-15 VDC Control
15-32 VDC Control
4-15 VDC Control
25 A
D2425D
D2425DE
H12D4825D
40 A
D2440DE
D2440D
H12D4840D
15-32 VDC Control H12D4825DE H12D4840D
OUTPUT SPECIFICATIONS (1)
Description
Operating Voltage (47-63Hz) [Vrms]
Transient Overvoltage [Vpk]
Maximum Off-State Leakage Current @ Rated Voltage [mArms]
Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (3)
Maximum Load Current [Arms] (4)
Minimum Load Current [Arms]
Maximum 1 Cycle Surge Current (50/60Hz) [Apk]
Maximum On-State Voltage Drop @ Rated Current [Vpk]
Thermal Resistance Junction to Case (Rjc) [°C/W]
48-530
1200 (2)
10
500
25
0.15
239/250
H12D4825xx
1.6
1.02
48-530
1200 (2)
10
500
40
0.15
597/625
H12D4840xx
1.6
0.63
24-280
600
10
500
40
0.15
597/6250
D2440xx
1.6
0.63
24-280
600
10
500
25
0.15
239/250
1.6
1.02
Maximum 1/2 Cycle I²t for Fusing (50/60 Hz) [A² sec] 285/259 1779/16211779/1621285/259
Minimum Power Factor (with Maximum Load) 0.5 0.50.50.5
D2425xx
Series
Output Voltage
D24: 24-280 VAC
H12D48: 48-530 VAC
Output Current
25: 25 Amps
40: 40 Amps
DH12D48 H
Control Voltage
D: 4-15 VDC
Thermal Pad
Blank: Not Included
H: Included
Required for valid part number
For options only and not required for valid part number
25
DE: 15-32 VDC
-10
Switching Mode
Blank: Zero Voltage Turn-On
-10: Random Turn-On
DataSheet
Panel Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2018 Crydom Inc. Specifications subject to change without notice.
Tolerances: ±0.02 in / 0.5 mm
All dimensions are in: inches [millimeters]
GENERAL SPECIFICATIONS (1)
Description Parameters
Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms
Minimum Insulation Resistance (@ 500 VDC) 109 Ohm
Maximum Capacitance, Input/Output 10 pF
Ambient Operating Temperature Range -40 to 80°C
Ambient Storage Temperature Range -40 to 125 °C
Weight (typical) 3.0 oz (86.5g)
Encapsulation Thermally Conductive Epoxy
Terminals .25" Fastons, .025" Square Pins
GENERAL NOTES
MECHANICAL SPECIFICATIONS
(1) All parameters at 25°C unless otherwise specified.
(2) For option (-10) models the Transient overvoltage is 1100Vac.
(3) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1
(4) Heat sinking required, for derating curves see next page.
(5) Turn-on time for random turn-on (-10) versions is 0.1 msec
INPUT SPECIFICATIONS (1)
Description H12D48XXD
4-15 VDC
4.0 VDC
1.0 VDC
13 mA
240 Ohm
1/2 Cycle
1/2 Cycle
D24XXD
4-15 VDC
4.0 VDC
1.0 VDC
13 mA
300 Ohm
1/2 Cycle
1/2 Cycle
E-SUFFIX
15-32 VDC
15.0 VDC
1.0 VDC
15 mA
1500 Ohm
1/2 Cycle
1/2 Cycle
Control Voltage Range
Minimum Turn-On Voltage
Minimum Turn-Off Voltage
Typical Input Current @ 5 VDC (@ 24 VDC for E-Suffix)
Nominal Input Impedance
Maximum Turn-On Time [msec] (5)
Maximum Turn-Off Time [msec]
FASTON
TERMINAL
.250 X .032
(4 PLACES)
MOUNTING
HOLE/SLOT
0.192 (4.9) DIA.
PIN .025 SQ.
.100 CENTERS
4 PLACES
120/240V MODEL 480V MODEL
.187 x .032
FASTON
TERMINAL
(4 PLACES)
.250 x .032 FASTON
TERMINAL
(4 PLACES)
MOUNTING HOLE/SLOT
.0192 (4.9) DIA.
2 PLC’S
.85
(21.6)
1.21
(30.6)
1.31
(33.2)
1.17
(29.7)
1.78
(45.3)
1.00
(25.4)
.45
(11.5)
.73
(18.5)
1.87
(47.5)
2.30
(58.4) 2.30
(58.4)
1.87
(47.5)
1.60
(40.6)
.77
(19.6)
.85
(21.6)
1.31
(33.2)
1.37
(34.8)
1.80
(45.7)
0.60
(15.2)
DataSheet
Panel Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2018 Crydom Inc. Specifications subject to change without notice.
WIRING DIAGRAM
THERMAL DERATE INFORMATION
AGENCY APPROVALS
E116949 (except 15-32VDC control)
Rev. 101018
ECN#20564
Ambient Temperature (ºC)
DERATE CURVE: 25 AMP Dual SSR DERATING CURVE: 40 A Dual SSR
Combined Channel Output Current (Amps)
LR81689 (240 V, 4-15VDC control only)
5902 UG
Ambient Temperature (ºC)
Combined Channel Output Current (Amps)
Agency Approvals
Designed in accordance with the requirements of IEC 62314
240V Model
480V Model
A2
A1
B1 LOAD B
LOAD B
LOAD A
LOAD A
120/240Vrms 120/240Vrms
480Vrms 480Vrms
- B CONTROL
+ B CONTROL
- A CONTROL
+ A CONTROL - B CONTROL
+ B CONTROL- A CONTROL
+ A CONTROL
B2
B2
B1
A2
A1
0.5 ºC/W
5.0 ºC/W
1.0 ºC/W
2.0 ºC/W
0.5 ºC/W
2.0 ºC/W
1.0 ºC/W
1.5 ºC/W
50
40
30
20
20 30 70605040 80
10
0
50
60
70
80
40
30
20
20 30 70605040 80
10
0
DataSheet
Panel Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2018 Crydom Inc. Specifications subject to change without notice.
WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告
RISK OF MATERIAL DAMAGE AND HOT
ENCLOSURE
• The product's side panels may be hot, allow
the product to cool before touching.
• Follow proper mounting instructions including
torque values.
• Do not allow liquids or foreign objects to enter
this product.
Failure to follow these instructions can result in
serious injury, or equipment damage.
RISQUE DE DOMMAGE MATERIEL ET DE
SURCHAUFFE DU BOITIER
• Les panneaux latéraux du produit peuvent être
chauds. Laisser le produit refroidir avant de le
toucher.
• Respecter les consignes de montage, et
notamment les couples de serrage.
• Ne pas laisser pénétrer de liquide ni de corps
étrangers à l'intérieur du produit.
Le non-respect de cette directive peut entraîner,
des lésions corporelles graves ou des
dommages matériels.
Die Nichtbeachtung dieser Anweisung kann
Körperverletzung oder Materialschäden
zur Folge haben.
GEFAHR VON MATERIALSCHÄDEN UND
GEHÄUSEERHITZUNG
• Die Seitenwände können heiß sein. Lassen Sie
das Produkt abkühlen, bevor Sie es berühren.
• Beachten Sie die Montageanweisungen,
• Führen Sie keine Flüssigkeiten oder
Fremdkörper in das Produkt ein.
Si no se respetan estas precauciones pueden
producirse graves lesiones, daños materiales.
RIESGO DE DAÑOS MATERIALES Y DE
SOBRECALENTAMIENTO DE LA UNIDAD
• Los paneles laterales del producto pueden
estar calientes. Esperar que el producto se
enfríe antes de tocarlo.
• Respetar las instrucciones de montaje, y en
particular los pares de apretado.
• No dejar que penetren líquidos o cuerpos
extraños en el producto.
La mancata osservanza di questa precauzione può
causare gravi rischi per l'incolumità personale o
danni alle apparecchiature.
RISCHIO DI DANNI MATERIALI E D'INVOLUCRO
CALDO
• I pannelli laterali dell'apparecchio possono
scottare; lasciar quindi raffreddare il prodotto
prima di toccarlo.
• Seguire le istruzioni di montaggio corrette.
• Non far entrare liquidi o oggetti estranei in questo
apparecchio.
如不能正确执行这些操作说明，
极有可能造成严重人体伤害或者设备的损坏。
材料损坏和高温外壳的危险性
• 产品的一侧面板可能很热，在其冷却前请
不要触碰。
• 遵照正确的安装说明，包括扭矩值。
• 请勿让液体及其他异物进入本产品。
DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险
HAZARD OF
ELECTRIC
SHOCK,
EXPLOSION,
OR ARC FLASH.
•Disconnect all
power before
installing or
working with
this equipment.
•Verify all
connections
and replace all
covers before
turning on
power.
Failure to follow
these
instructions will
result in death
or serious injury.
RIESGO DE
DESCARGA
ELECTRICA O
EXPLOSION.
•Desconectar
todos los
suministros de
energia a este
equipo antes
de trabajar
con este equipo.
•Verificar todas
las conexiones
y colocar todas
las tapas antes
de energizer
el equipo.
El
incumplimiento
de estas
instrucciones
puede provocar
la muerte o
lesiones serias.
RISQUE DE
DESCHARGE
ELECTRIQUE
OU EXPLOSION
•Eteindre
toutes les
sources
d'énergie de
cet appareil
avant de
travailler
dessus de cet
appareil
•Vérifier tous
connections, et
remettre tous
couverts en
olace avant de
mettre sous
De non-suivi de
ces instructions
provoquera la
mort ou des
lésions sérieuses
sérieuses.
GEFAHR EINES
ELEKTRISCHE
N SCHLAGES
ODER EINER
EXPLOSION.
•Stellen Sie
jeglichen
Strom ab, der
dieses Gerät
versorgt, bevor
Sie an dem
Gerät Arbeiten
durchführen
•Vor dem
Drehen auf
Energie alle
Anschlüsse
überprüfen
und alle
Abdeckungen
ersetzen.
Unterlassung
dieser
Anweisungen
können zum
Tode oder zu
schweren
Verletzungen
führen.
RISCHIO DI
SCOSSA
ELETTRICA O
DELL’ESPLOSIONE.
•Spenga tutta
l'alimentazione
che fornisce
questa
apparecchiatura
prima di lavorare
a questa
apparecchiatura
•Verificare tutti
i collegamenti
e sostituire
tutte le coperture
prima
dell’accensione
L'omissione di
queste istruzioni
provocherà la
morte o
lesioni serie
存在电击、
爆炸或电弧
闪烁危险
•
在操作此设
备之前请先
关闭电源。
若不遵守这些说明，
可能会导致严重的
人身伤害甚至死亡。
DataSheet
Panel Mount
Do not forget to visit us at:
www.crydom.com
Copyright © 2018 Crydom Inc. Specifications subject to change without notice.
ANNEX - ENVIRONMENTAL INFORMATION
The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China
Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products.
Part
Name
Toxic or hazardous Substance and Elements
Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated
(Pb) (Hg) (Cd) Chromium
(Cr (VI))
biphenyls
(PBB)
diphenyl ethers
(PBDE)
Semiconductor die
Solder
附件 - 环保信息
此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006,
电子信息产品污染控制标识要求。
有毒有害物质或元素件部
名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚
(Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE)
半导体芯片
焊接点
50
