SPEC NO: DSAG4998 REV NO: V.11A DATE: JAN/09/2015 PAGE: 1 OF 5
APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1361000058
SURFACE MOUNT DISPLAY
Part Number: ACPSC04-41SEKWA
Super Bright Orange
Features
0.4 inch character height.
Low current operation.
High contrast and light output.
Categorized for luminous intensity.
Mechanically rugged.
Gray face,white segment.
Package : 400pcs / reel.
Moisture sensitivity level : level 2a.
RoHS compliant.
Description
The Super Bright Orange device is made with AlGaInP (on
GaAs substrate) light emitting diode chip.
Package Dimensions& Intern al Circuit Diagram
Notes:
1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted.
2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
3.The gap between the reflector and PCB shall not exceed 0.25mm
SPEC NO: DSAG4998 REV NO: V.11A DATE: JAN/09/2015 PAGE: 2 OF 5
APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1361000058
Selection Guide
Absolute Maximum Ratings at TA=25°C
Electrical / Optical Characteristics at TA=25°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Symbol Parameter Device Typ. Max. Units Test Conditions
λpeak Peak Wavelength Super Bright Orange 610 nm IF=20mA
λD [1] Dominant Wavelength Super Bright Orange 601 nm IF=20mA
Δλ1/2 Spectral Line Half-width Super Bright Orange 29 nm IF=20mA
C Capacitance Super Bright Orange 15 pF VF=0V;f=1MHz
VF [2] Forward Voltage Super Bright Orange 2.1 2.5 V IF=20mA
IR Reverse Current Super Bright Orange 10 uA VR=5V
Parameter Super Bright Orange Units
Power dissipation 75 mW
DC Forward Current 30 mA
Peak Forward Current [1] 195 mA
Reverse Voltage 5 V
Operating / Storage Temperature -40°C To +85°C
Note:
1. Luminous intensity/ luminous Flux: +/-15%.
*Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Part No. Dice Lens Type
Iv (ucd) [1]
@ 10mA Description
Min. Typ.
Super Bright Orange (AlGaInP) White Diffused
21000 44000
Common Cathode, Rt.
Hand Decimal.
*5600 *13000
ACPSC04-41SEKWA
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to the CIE127-2007 compliant national standards.
4. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
SPEC NO: DSAG4998 REV NO: V.11A DATE: JAN/09/2015 PAGE: 3 OF 5
APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1361000058
Super Bright Orange ACPSC04-41SEKWA
SPEC NO: DSAG4998 REV NO: V.11A DATE: JAN/09/2015 PAGE: 4 OF 5
APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1361000058
ACPSC04-41SEKWA
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.15)
Reel Dimension
Tape Specifications
(Units : mm)
SPEC NO: DSAG4998 REV NO: V.11A DATE: JAN/09/2015 PAGE: 5 OF 5
APPROVED: WYNEC CHECKED: Joe Lee DRAWN: P.Cheng ERP: 1361000058
PACKING & LABEL SPECIFICATIONS ACPSC04-41SEKWA
Terms and conditions for the usage of this doc ument
1.The information included in this document reflects representative usage scenarios and is intended
for technical reference only.
2.The part number, type, and specifications mentioned in this document are subject to future change
and improvement without notice. Before production usage customer should refer to the latest
datasheet for the updated specifications.
3.When using the products referenced in this document, please make sure the product is being
operated within the environmental and electrical limits specified in the datasheet. If customer usage
exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4.The information in this document applies to typical usage in consumer electronics applications.
If customer's application has special reliability requirements or have life-threatening liabilities,
such as automotive or medical usage, please consult with Kingbright representative for further
assistance.
5.The contents and information of this document may not be reproduced or re-transmitted without
permission by Kingbright.
6.All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
