S-1135 Series www.sii-ic.com HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 (c) Seiko Instruments Inc., 2008-2010 S-1135 Series, developed using the CMOS technology, is a positive voltage regulator IC which has the low dropout voltage, the high-accuracy output voltage and the low current consumption (300 mA output current). A 1.0 F small ceramic capacitor can be used. It operates with low current consumption of 45 A typ. The overcurrent protection circuit prevents the load current from exceeding the capacitance of output transistor. The power-off circuit ensures longer battery life. Various capacitors, also small ceramic capacitors, can be used for this IC more than for the conventional regulator ICs which have CMOS technology. Furthermore a small SOT-89-5, SOT-23-5, and HSNT-6A packages realize high-density mounting. Features * Output voltage: * Low equivalent series resistance capacitor : * Wide input voltage range: * High-accuracy output voltage: * Low dropout voltage: * Low current consumption: * Output current: * High ripple rejection: * Built-in overcurrent protection circuit: * Built-in power-off circuit: * Discharge shunt circuit can be selected. * Resistor is selectable in pull-up or pull-down * Lead-free, Sn 100%, halogen-free*2 1.0 V to 3.5 V, selectable in 0.05 V step. Ceramic capacitor of 1.0 F or more can be used as the I/O capacitor. 1.5 V to 5.5 V 1.0% (1.0 V to 1.45 V output product : 15 mV) 160 mV typ. (products having the output of 2.6 V, IOUT = 300 mA) During operation: 45 A typ., 65 A max. During power-off: 0.1 A typ., 1.0 A max. Possible to output 300 mA (at VIN VOUT(S) + 1.0 V)*1 70 dB typ. (at 1.0 kHz, VOUT = 1.0 V) limits overcurrent of output transistor Ensures long battery life. *1. Attention should be paid to the power dissipation of the package when the output current is large. *2. Refer to " Product Name Structure" for details. Applications * Power supply for battery-powered devices * Power supply for cellular phones * Power supply for portable equipment Packages * SOT-89-5 * SOT-23-5 * HSNT-6A Seiko Instruments Inc. 1 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Block Diagrams 1. S-1135 Series A type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "H" Available None Available + - Reference voltage circuit *1 VSS *1. Parasitic diode Figure 1 2. S-1135 Series B type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit + - Reference voltage circuit *1 VSS *1. Parasitic diode Figure 2 2 Seiko Instruments Inc. Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "H" Available None None HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 3. S-1135 Series C type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "H" None None Available + - Reference voltage circuit VSS *1. Parasitic diode Figure 3 4. S-1135 Series D type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "H" None None None + - Reference voltage circuit VSS *1. Parasitic diode Figure 4 Seiko Instruments Inc. 3 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 5. S-1135 Series E type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "L" Available Available None + - Reference voltage circuit *1 VSS *1. Parasitic diode Figure 5 6. S-1135 Series F type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit + - Reference voltage circuit *1 VSS *1. Parasitic diode Figure 6 4 Seiko Instruments Inc. Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "L" Available None None HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 7. S-1135 Series G type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "L" None Available None + - Reference voltage circuit VSS *1. Parasitic diode Figure 7 8. S-1135 Series H type *1 VIN VOUT Overcurrent protection circuit ON / OFF Power-off circuit Function ON / OFF logic Discharge shunt function Pull-up resistor Pull-down resistor Status Active "L" None None None + - Reference voltage circuit VSS *1. Parasitic diode Figure 8 Seiko Instruments Inc. 5 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Product Name Structure Users can select the product type, output voltage, and package type for the S-1135 Series. Refer to Refer to "1. Product name" regarding the contents of product name, "2. Function list of product type" regarding the product type, "3. Package" regarding the package drawings. 1. Product name (1) SOT-89-5 S-1135 x xx - U5T1 x Environmental code U : Lead-free (Sn 100%), halogen-free G : Lead-free (for details, please contact our sales office) Package abbreviation and IC packing specifications U5T1: SOT-89-5, tape product *1 *2 Output voltage 10 to 35 (e.g., when the output voltage is 1.0 V, it is expressed as 10.) *3 Product type A to H *1. *2. *3. Refer to the tape specifications. If you request the product which has 0.05 V step, contact our sales office. Refer to "2. Function list of product type". (2) SOT-23-5, HSNT-6A S-1135 x xx - xxxx x Environmental code U : Lead-free (Sn 100%), halogen-free S : Lead-free, halogen-free Package abbreviation and IC packing specifications*1 M5T1: SOT-23-5, tape product A6T1: HSNT-6A, tape product Output voltage*2 10 to 35 (e.g., when the output voltage is 1.0 V, it is expressed as 10.) *3 Product type A to H *1. *2. *3. 6 Refer to the tape specifications. If you request the product which has 0.05 V step, contact our sales office. Refer to "2. Function list of product type". Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 2. Function list of product type Table 1 Product Type 3. ON / OFF Logic Discharge Shunt Function Pull-up Resistor Pull-down Resistor A Active high Available None Available B Active high Available None None C Active high None None Available D Active high None None None E Active low Available Available None F Active low Available None None G Active low None Available None H Active low None None None Package Package Name SOT-89-5 SOT-23-5 HSNT-6A Package Tape Drawing Code Reel UP005-A-P-SD MP005-A-P-SD PJ006-A-P-SD UP005-A-C-SD MP005-A-C-SD PJ006-A-C-SD UP005-A-R-SD MP005-A-R-SD PJ006-A-R-SD Seiko Instruments Inc. Land PJ006-A-LM-SD Stencil Opening PJ006-A-LM-SD 7 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 4. Product name list 4. 1 S-1135 series A type ON / OFF logic: Discharge shunt function: Active high Available Pull-up resistor: Pull-down resistor: None Available Table 2 Output Voltage SOT-89-5 SOT-23-5 HSNT-6A 1.0 V 15 mV S-1135A10-U5T1x S-1135A10-M5T1y S-1135A10-A6T1y 1.1 V 15 mV S-1135A11-U5T1x S-1135A11-M5T1y S-1135A11-A6T1y 1.2 V 15 mV S-1135A12-U5T1x S-1135A12-M5T1y S-1135A12-A6T1y 1.3 V 15 mV S-1135A13-U5T1x S-1135A13-M5T1y S-1135A13-A6T1y 1.4 V 15 mV S-1135A14-U5T1x S-1135A14-M5T1y S-1135A14-A6T1y 1.5 V 1.0% S-1135A15-U5T1x S-1135A15-M5T1y S-1135A15-A6T1y 1.6 V 1.0% S-1135A16-U5T1x S-1135A16-M5T1y S-1135A16-A6T1y 1.7 V 1.0% S-1135A17-U5T1x S-1135A17-M5T1y S-1135A17-A6T1y 1.8 V 1.0% S-1135A18-U5T1x S-1135A18-M5T1y S-1135A18-A6T1y 1.85 V 1.0% S-1135A1J-U5T1x S-1135A1J-M5T1y S-1135A1J-A6T1y 1.9 V 1.0% S-1135A19-U5T1x S-1135A19-M5T1y S-1135A19-A6T1y 2.0 V 1.0% S-1135A20-U5T1x S-1135A20-M5T1y S-1135A20-A6T1y 2.1 V 1.0% S-1135A21-U5T1x S-1135A21-M5T1y S-1135A21-A6T1y 2.2 V 1.0% S-1135A22-U5T1x S-1135A22-M5T1y S-1135A22-A6T1y 2.3 V 1.0% S-1135A23-U5T1x S-1135A23-M5T1y S-1135A23-A6T1y 2.4 V 1.0% S-1135A24-U5T1x S-1135A24-M5T1y S-1135A24-A6T1y 2.5 V 1.0% S-1135A25-U5T1x S-1135A25-M5T1y S-1135A25-A6T1y 2.6 V 1.0% S-1135A26-U5T1x S-1135A26-M5T1y S-1135A26-A6T1y 2.7 V 1.0% S-1135A27-U5T1x S-1135A27-M5T1y S-1135A27-A6T1y 2.8 V 1.0% S-1135A28-U5T1x S-1135A28-M5T1y S-1135A28-A6T1y 2.85 V 1.0% S-1135A2J-U5T1x S-1135A2J-M5T1y S-1135A2J-A6T1y 2.9 V 1.0% S-1135A29-U5T1x S-1135A29-M5T1y S-1135A29-A6T1y 3.0 V 1.0% S-1135A30-U5T1x S-1135A30-M5T1y S-1135A30-A6T1y 3.1 V 1.0% S-1135A31-U5T1x S-1135A31-M5T1y S-1135A31-A6T1y 3.2 V 1.0% S-1135A32-U5T1x S-1135A32-M5T1y S-1135A32-A6T1y 3.3 V 1.0% S-1135A33-U5T1x S-1135A33-M5T1y S-1135A33-A6T1y 3.4 V 1.0% S-1135A34-U5T1x S-1135A34-M5T1y S-1135A34-A6T1y 3.5 V 1.0% S-1135A35-U5T1x S-1135A35-M5T1y S-1135A35-A6T1y Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 8 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 4. 2 S-1135 series B type ON / OFF logic: Discharge shunt function: Active high Available Pull-up resistor: Pull-down resistor: None None Table 3 Output Voltage SOT-89-5 SOT-23-5 HSNT-6A 1.0 V 15 mV S-1135B10-U5T1x S-1135B10-M5T1y S-1135B10-A6T1y 1.1 V 15 mV S-1135B11-U5T1x S-1135B11-M5T1y S-1135B11-A6T1y 1.2 V 15 mV S-1135B12-U5T1x S-1135B12-M5T1y S-1135B12-A6T1y 1.3 V 15 mV S-1135B13-U5T1x S-1135B13-M5T1y S-1135B13-A6T1y 1.4 V 15 mV S-1135B14-U5T1x S-1135B14-M5T1y S-1135B14-A6T1y 1.5 V 1.0% S-1135B15-U5T1x S-1135B15-M5T1y S-1135B15-A6T1y 1.6 V 1.0% S-1135B16-U5T1x S-1135B16-M5T1y S-1135B16-A6T1y 1.7 V 1.0% S-1135B17-U5T1x S-1135B17-M5T1y S-1135B17-A6T1y 1.8 V 1.0% S-1135B18-U5T1x S-1135B18-M5T1y S-1135B18-A6T1y 1.85 V 1.0% S-1135B1J-U5T1x S-1135B1J-M5T1y S-1135B1J-A6T1y 1.9 V 1.0% S-1135B19-U5T1x S-1135B19-M5T1y S-1135B19-A6T1y 2.0 V 1.0% S-1135B20-U5T1x S-1135B20-M5T1y S-1135B20-A6T1y 2.1 V 1.0% S-1135B21-U5T1x S-1135B21-M5T1y S-1135B21-A6T1y 2.2 V 1.0% S-1135B22-U5T1x S-1135B22-M5T1y S-1135B22-A6T1y 2.3 V 1.0% S-1135B23-U5T1x S-1135B23-M5T1y S-1135B23-A6T1y 2.4 V 1.0% S-1135B24-U5T1x S-1135B24-M5T1y S-1135B24-A6T1y 2.5 V 1.0% S-1135B25-U5T1x S-1135B25-M5T1y S-1135B25-A6T1y 2.6 V 1.0% S-1135B26-U5T1x S-1135B26-M5T1y S-1135B26-A6T1y 2.7 V 1.0% S-1135B27-U5T1x S-1135B27-M5T1y S-1135B27-A6T1y 2.8 V 1.0% S-1135B28-U5T1x S-1135B28-M5T1y S-1135B28-A6T1y 2.85 V 1.0% S-1135B2J-U5T1x S-1135B2J-M5T1y S-1135B2J-A6T1y 2.9 V 1.0% S-1135B29-U5T1x S-1135B29-M5T1y S-1135B29-A6T1y 3.0 V 1.0% S-1135B30-U5T1x S-1135B30-M5T1y S-1135B30-A6T1y 3.1 V 1.0% S-1135B31-U5T1x S-1135B31-M5T1y S-1135B31-A6T1y 3.2 V 1.0% S-1135B32-U5T1x S-1135B32-M5T1y S-1135B32-A6T1y 3.3 V 1.0% S-1135B33-U5T1x S-1135B33-M5T1y S-1135B33-A6T1y 3.4 V 1.0% S-1135B34-U5T1x S-1135B34-M5T1y S-1135B34-A6T1y 3.5 V 1.0% S-1135B35-U5T1x S-1135B35-M5T1y S-1135B35-A6T1y Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Seiko Instruments Inc. 9 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 4. 3 S-1135 series C type ON / OFF logic: Discharge shunt function: Active high None Pull-up resistor: Pull-down resistor: None Available Table 4 Output Voltage SOT-89-5 SOT-23-5 HSNT-6A 1.0 V 15 mV S-1135C10-U5T1x S-1135C10-M5T1y S-1135C10-A6T1y 1.1 V 15 mV S-1135C11-U5T1x S-1135C11-M5T1y S-1135C11-A6T1y 1.2 V 15 mV S-1135C12-U5T1x S-1135C12-M5T1y S-1135C12-A6T1y 1.3 V 15 mV S-1135C13-U5T1x S-1135C13-M5T1y S-1135C13-A6T1y 1.4 V 15 mV S-1135C14-U5T1x S-1135C14-M5T1y S-1135C14-A6T1y 1.5 V 1.0% S-1135C15-U5T1x S-1135C15-M5T1y S-1135C15-A6T1y 1.6 V 1.0% S-1135C16-U5T1x S-1135C16-M5T1y S-1135C16-A6T1y 1.7 V 1.0% S-1135C17-U5T1x S-1135C17-M5T1y S-1135C17-A6T1y 1.8 V 1.0% S-1135C18-U5T1x S-1135C18-M5T1y S-1135C18-A6T1y 1.85 V 1.0% S-1135C1J-U5T1x S-1135C1J-M5T1y S-1135C1J-A6T1y 1.9 V 1.0% S-1135C19-U5T1x S-1135C19-M5T1y S-1135C19-A6T1y 2.0 V 1.0% S-1135C20-U5T1x S-1135C20-M5T1y S-1135C20-A6T1y 2.1 V 1.0% S-1135C21-U5T1x S-1135C21-M5T1y S-1135C21-A6T1y 2.2 V 1.0% S-1135C22-U5T1x S-1135C22-M5T1y S-1135C22-A6T1y 2.3 V 1.0% S-1135C23-U5T1x S-1135C23-M5T1y S-1135C23-A6T1y 2.4 V 1.0% S-1135C24-U5T1x S-1135C24-M5T1y S-1135C24-A6T1y 2.5 V 1.0% S-1135C25-U5T1x S-1135C25-M5T1y S-1135C25-A6T1y 2.6 V 1.0% S-1135C26-U5T1x S-1135C26-M5T1y S-1135C26-A6T1y 2.7 V 1.0% S-1135C27-U5T1x S-1135C27-M5T1y S-1135C27-A6T1y 2.8 V 1.0% S-1135C28-U5T1x S-1135C28-M5T1y S-1135C28-A6T1y 2.85 V 1.0% S-1135C2J-U5T1x S-1135C2J-M5T1y S-1135C2J-A6T1y 2.9 V 1.0% S-1135C29-U5T1x S-1135C29-M5T1y S-1135C29-A6T1y 3.0 V 1.0% S-1135C30-U5T1x S-1135C30-M5T1y S-1135C30-A6T1y 3.1 V 1.0% S-1135C31-U5T1x S-1135C31-M5T1y S-1135C31-A6T1y 3.2 V 1.0% S-1135C32-U5T1x S-1135C32-M5T1y S-1135C32-A6T1y 3.3 V 1.0% S-1135C33-U5T1x S-1135C33-M5T1y S-1135C33-A6T1y 3.4 V 1.0% S-1135C34-U5T1x S-1135C34-M5T1y S-1135C34-A6T1y 3.5 V 1.0% S-1135C35-U5T1x S-1135C35-M5T1y S-1135C35-A6T1y Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 10 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 4. 4 S-1135 series D type ON / OFF logic: Discharge shunt function: Active high None Pull-up resistor: Pull-down resistor: None None Table 5 Output Voltage SOT-89-5 SOT-23-5 HSNT-6A 1.0 V 15 mV S-1135D10-U5T1x S-1135D10-M5T1y S-1135D10-A6T1y 1.1 V 15 mV S-1135D11-U5T1x S-1135D11-M5T1y S-1135D11-A6T1y 1.2 V 15 mV S-1135D12-U5T1x S-1135D12-M5T1y S-1135D12-A6T1y 1.3 V 15 mV S-1135D13-U5T1x S-1135D13-M5T1y S-1135D13-A6T1y 1.4 V 15 mV S-1135D14-U5T1x S-1135D14-M5T1y S-1135D14-A6T1y 1.5 V 1.0% S-1135D15-U5T1x S-1135D15-M5T1y S-1135D15-A6T1y 1.6 V 1.0% S-1135D16-U5T1x S-1135D16-M5T1y S-1135D16-A6T1y 1.7 V 1.0% S-1135D17-U5T1x S-1135D17-M5T1y S-1135D17-A6T1y 1.8 V 1.0% S-1135D18-U5T1x S-1135D18-M5T1y S-1135D18-A6T1y 1.85 V 1.0% S-1135D1J-U5T1x S-1135D1J-M5T1y S-1135D1J-A6T1y 1.9 V 1.0% S-1135D19-U5T1x S-1135D19-M5T1y S-1135D19-A6T1y 2.0 V 1.0% S-1135D20-U5T1x S-1135D20-M5T1y S-1135D20-A6T1y 2.1 V 1.0% S-1135D21-U5T1x S-1135D21-M5T1y S-1135D21-A6T1y 2.2 V 1.0% S-1135D22-U5T1x S-1135D22-M5T1y S-1135D22-A6T1y 2.3 V 1.0% S-1135D23-U5T1x S-1135D23-M5T1y S-1135D23-A6T1y 2.4 V 1.0% S-1135D24-U5T1x S-1135D24-M5T1y S-1135D24-A6T1y 2.5 V 1.0% S-1135D25-U5T1x S-1135D25-M5T1y S-1135D25-A6T1y 2.6 V 1.0% S-1135D26-U5T1x S-1135D26-M5T1y S-1135D26-A6T1y 2.7 V 1.0% S-1135D27-U5T1x S-1135D27-M5T1y S-1135D27-A6T1y 2.8 V 1.0% S-1135D28-U5T1x S-1135D28-M5T1y S-1135D28-A6T1y 2.85 V 1.0% S-1135D2J-U5T1x S-1135D2J-M5T1y S-1135D2J-A6T1y 2.9 V 1.0% S-1135D29-U5T1x S-1135D29-M5T1y S-1135D29-A6T1y 3.0 V 1.0% S-1135D30-U5T1x S-1135D30-M5T1y S-1135D30-A6T1y 3.1 V 1.0% S-1135D31-U5T1x S-1135D31-M5T1y S-1135D31-A6T1y 3.2 V 1.0% S-1135D32-U5T1x S-1135D32-M5T1y S-1135D32-A6T1y 3.3 V 1.0% S-1135D33-U5T1x S-1135D33-M5T1y S-1135D33-A6T1y 3.4 V 1.0% S-1135D34-U5T1x S-1135D34-M5T1y S-1135D34-A6T1y 3.5 V 1.0% S-1135D35-U5T1x S-1135D35-M5T1y S-1135D35-A6T1y Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Seiko Instruments Inc. 11 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Pin Configuration SOT-89-5 Top view 5 4 *1. 1 2 Table 6 Pin No. Symbol Description 1 VOUT Output voltage pin 2 VSS GND pin 3 No connection NC*1 4 ON / OFF ON / OFF pin 5 VIN Input voltage pin The NC pin is electrically open. The NC pin can be connected to VIN or VSS. 3 Figure 9 SOT-23-5 Top view 5 4 *1. 1 2 Table 7 Pin No. Symbol Description 1 VIN Input voltage pin 2 VSS GND pin 3 ON / OFF ON / OFF pin 4 No connection NC*1 5 VOUT Output voltage pin The NC pin is electrically open. The NC pin can be connected to VIN or VSS. 3 Figure 10 HSNT-6A Top view 1 6 2 5 3 4 *1. Bottom view 6 1 5 2 4 3 Table 8 Pin No. Symbol Description 1 VOUT Output voltage pin 2 VSS GND pin 3 No connection NC*1 4 ON / OFF ON / OFF pin 5 No connection NC*1 6 VIN Input voltage pin The NC pin is electrically open. The NC pin can be connected to VIN or VSS. *1 *1. Connect the heatsink of backside at shadowed area to the board, and set electric potential open or GND. However, do not use it as the function of electrode. Figure 11 12 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Absolute Maximum Ratings Table 9 Item Symbol VIN VON / OFF VOUT Input voltage Output voltage SOT-89-5 PD SOT-23-5 HSNT-6A Operating ambient temperature Topr Storage temperature Tstg *1. When mounted on board [Mounted board] (1) Board size : 114.3 mm x 76.2 mm x t1.6 mm (2) Name : JEDEC STANDARD51-7 *2. When mounted on board [Mounted board] (1) Board size : 50 mm x 50 mm x t1.6 mm (2) Wiring ratio : 50% Power dissipation VSS - 0.3 to VSS + 6.0 VSS - 0.3 to VIN + 0.3 VSS - 0.3 to VIN + 0.3 1000*1 600*1 1000*2 -40 to +85 -40 to +125 V V V mW mW mW C C The absolute maximum ratings are rated values exceeding which the product could suffer physical damage. These values must therefore not be exceeded under any conditions. 1200 Power Dissipation (PD) [mW] Caution (Ta = 25C unless otherwise specified) Absolute Maximum Rating Unit 1000 SOT-89-5 HSNT-6A 800 600 400 SOT-23-5 200 0 0 150 100 50 Ambient Temperature (Ta) [C] Figure 12 Power Dissipation of Package Seiko Instruments Inc. 13 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Electrical Characteristics Table 10 (1 / 2) Item Output voltage Output current *1 *2 Symbol 1.0 V VOUT(S) < 1.1 V 1.1 V VOUT(S) < 1.2 V 1.2 V VOUT(S) < 1.3 V 1.3 V VOUT(S) < 1.4 V 1.4 V VOUT(S) < 1.5 V 1.5 V VOUT(S) < 2.0 V 2.0 V VOUT(S) < 2.6 V 2.6 V VOUT(S) 3.5 V VOUT(S) - 0.015 VOUT(S) x 0.99 300*5 0.50 1.0 V VOUT(S) < 1.1 V 0.05 0.2 %/V 1 1.1 V VOUT(S) 3.5 V 0.05 0.2 %/V 1 1.0 V VOUT(S) 2.0 V 2.0 V < VOUT(S) 3.5 V VIN = VOUT(S) + 1.0 V, 1.0 V VOUT(S) 3.0 V 1.0 mA IOUT 300 mA 3.0 V < VOUT(S) 3.5 V VIN = VOUT(S) + 1.0 V, IOUT = 100 mA, -40C Ta +85C 15 15 30 30 20 25 40 45 mV mV mV mV 1 1 1 1 130 ppm/C 1 ISS1 VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON, no load 45 65 A 2 ISS2 VIN = VOUT(S) + 1.0 V, ON / OFF pin = OFF, no load 0.1 1.0 A 2 VIN VIN = VOUT(S) + 1.0 V, RL = 1.0 k determined by VOUT output level VIN = VOUT(S) + 1.0 V, RL = 1.0 k determined by VOUT output level VIN = 5.5 V, B / D / E / F / G / H type VON / OFF = 5.5 V A / C type VIN = 5.5 V, A / B / C / D / F / H type VON / OFF = 0 V E / G type VIN = VOUT(S) + 1.0 V, 1.0 V VOUT(S) 1.2 V f = 1.0 kHz, Vrip = 0.5 Vrms, 1.2 V < VOUT(S) 3.5 V IOUT = 50 mA 1.5 5.5 V 1.0 V 4 0.3 V 4 -0.1 1.0 -0.1 1.0 2.5 2.5 0.1 5.0 0.1 5.0 A A A A 4 4 4 4 70 dB 5 65 dB 5 100 mA 3 VOUT(E) IOUT Dropout voltage*3 Vdrop Line regulation VOUT1 VIN* VOUT Load regulation Output voltage *4 temperature coefficient Current consumption during operation Current consumption during power-off Input voltage ON / OFF pin input voltage "H" ON / OFF pin input voltage "L" ON / OFF pin input current "H" ON / OFF pin input current "L" Ripple rejection Short-circuit current 14 Conditions (Ta = 25C unless otherwise specified) Test Min. Typ. Max. Unit Circuit VOUT2 VOUT Ta * VOUT VSH VSL ISH ISL RR Ishort VIN = VOUT(S) + 1.0 V, IOUT = 100 mA 1.0 V VOUT(S) < 1.5 V 1.5 V VOUT(S) 3.5 V VIN VOUT(S) + 1.0 V IOUT = 300 mA 1.6 V VIN 5.5 V, IOUT = 100 mA VOUT(S) + 0.5 V VIN 5.5 V, IOUT = 100 mA VIN = VOUT(S) + 1.0 V, 1.0 mA IOUT 150 mA VIN = VOUT(S) + 1.0 V, ON / OFF pin = ON, VOUT = 0 V Seiko Instruments Inc. 0.61 0.49 0.38 0.31 0.27 0.25 0.21 0.16 VOUT(S) + 0.015 VOUT(S) x 1.01 0.72 0.61 0.53 0.47 0.41 0.38 0.32 0.26 VOUT(S) VOUT(S) V 1 V 1 mA V V V V V V V V 3 1 1 1 1 1 1 1 1 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Table 10 (2 / 2) S-1135 Series A / B / E / F type (With discharge shunt function) Item "L" output Nch ON resistance Symbol RLOW Conditions VOUT = 0.1 V, VIN = 5.5 V Min. Typ. Max. Unit Test Circuit 35 3 Min. Typ. Max. Unit Test Circuit S-1135 Series A / C / E / G type (With pull-up / pull-down resistor) Item Symbol Conditions Power-off pull-up / RPD 1.0 2.2 5.0 M 4 pull-down resistor *1. VOUT(S): Specified output voltage VOUT(E): Actual output voltage Output voltage when fixing IOUT(= 100 mA) and inputting VOUT(S) +1.0 V *2. The output current at which the output voltage becomes 95% of VOUT(E) after gradually increasing the output current. *3. Vdrop = VIN1 - (VOUT3 x 0.98) VOUT3 is the output voltage when VIN = VOUT(S) + 1.0 V and IOUT = 300 mA. VIN1 is the input voltage at which the output voltage becomes 98% of VOUT3 after gradually decreasing the input voltage. *4. The change in temperature [mV/C] is calculated using the following equation. VOUT VOUT [mV/C]*1 = VOUT(S)[V]*2 x Ta*V [ppm/C]*3 / 1000 Ta OUT *1. Change in temperature of the output voltage *2. Specified output voltage *3. Output voltage temperature coefficient *5. The output current can be at least this value. Due to restrictions on the package power dissipation, this value may not be satisfied. Attention should be paid to the power dissipation of the package when the output current is large. This specification is guaranteed by design. Seiko Instruments Inc. 15 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Test Circuits 1. + VOUT VIN A + ON / OFF V VSS Set to power ON Figure 13 2. + A VOUT VIN ON / OFF VSS Set to VIN or GND Figure 14 + 3. VOUT VIN A + ON / OFF VSS V Set to VIN or GND Figure 15 4. VOUT VIN + A + ON / OFF VSS V RL Figure 16 5. VIN VOUT + ON / OFF VSS V Set to power ON Figure 17 16 Seiko Instruments Inc. RL HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Standard Circuit Input Output VOUT VIN CIN *1 ON / OFF VSS Single GND *1. *2. CL *2 GND CIN is a capacitor for stabilizing the input. Ceramic capacitor of 1.0 F or more can be used as CL. Figure 18 Caution The above connection diagram and constant will not guarantee successful operation. Perform thorough evaluation using the actual application to set the constant. Condition of Application Input capacitor (CIN) : Output capacitor (CL) : 1.0 F or more 1.0 F or more (ceramic capacitor) Caution A general series regulator may oscillate, depending on the external components. Confirm that no oscillation occurs in the application for which the above capacitors are used. Selection of Input and Output Capacitors (CIN, CL) The S-1135 Series requires an output capacitor between the VOUT and VSS pin for phase compensation. Operation is stabilized by a ceramic capacitor with an output capacitance of 1.0 F or more over the entire temperature range. When using an OS capacitor, tantalum capacitor, or aluminum electrolytic capacitor, the capacitance must be 1.0 F or more. The value of the output overshoot or undershoot transient response varies depending on the value of the output capacitor. The required capacitance of the input capacitor differs depending on the application. The recommended capacitance for an application is CIN 1.0 F, CL 1.0 F; however, when selecting the output capacitor, perform sufficient evaluation, including evaluation of temperature characteristics, on the actual device. Seiko Instruments Inc. 17 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Explanation of Terms 1. Low dropout voltage regulator This IC's voltage regulator has the low dropout voltage due to its built-in low on-resistance transistor. 2. Output voltage (VOUT) The accuracy of the output voltage is ensured at 1.0% or 15 mV*1 under the specified conditions of fixed input voltage*2, fixed output current, and fixed temperature. *1. *2. When VOUT < 1.5 V : 15 mV, When 1.5 V VOUT : 1.0% Differs depending on the product. Caution 3. If the above conditions change, the output voltage value may vary and exceed the accuracy range of the output voltage. Refer to " Electrical Characteristics" and " Characteristics (Typical Data)" for details. VOUT1 Line regulation VIN*VOUT Indicates the dependency of the output voltage on the input voltage. That is, the values show how much the output voltage changes due to a change in the input voltage with the output current remaining unchanged. 4. Load regulation (VOUT2) Indicates the dependency of the output voltage on the output current. That is, the values show how much the output voltage changes due to a change in the output current with the input voltage remaining unchanged. 5. Dropout voltage (Vdrop) Indicates the difference between input voltage VIN and the output voltage when; decreasing input voltage VIN gradually until the output voltage has dropped out to the value of 98% of output voltage VOUT3, which is at VIN = VOUT(S) + 1.0 V. Vdrop = VIN1 - (VOUT3 x 0.98) 18 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series VOUT 6. Temperature coefficient of output voltage Ta*VOUT The shaded area in Figure 19 is the range where VOUT varies in the operating temperature range when the temperature coefficient of the output voltage is 130 ppm/C. Example of S-1135B30 typ. products VOUT [V] +0.39 mV/C *1 VOUT(E) -0.39 mV/C -40 *1. 25 85 Ta [C] VOUT(E) is the value of the output voltage measured at 25C. Figure 19 A change in the temperature of the output voltage [mV/C] is calculated using the following equation. VOUT VOUT [mV/C]*1 = VOUT(S)[V]*2 x Ta*V [ppm/C]*3 / 1000 Ta OUT *1. Change in temperature of output voltage *2. Specified output voltage *3. Output voltage temperature coefficient Seiko Instruments Inc. 19 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Operation 1. Basic operation Figure 20 shows the block diagram of S-1135 Series. The error amplifier compares the reference voltage (Vref) with Vfb, which is the output voltage resistance-divided by feedback resistors Rs and Rf. It supplies the gate voltage necessary to maintain the constant output voltage which is not influenced by the input voltage and temperature change, to the output transistor. VIN *1 Current supply Error amplifier Vref VOUT - Rf + Vfb Reference voltage circuit Rs VSS *1. Parasitic diode Figure 20 2. Output transistor In the S-1135 Series, a low on-resistance P-channel MOS FET is used as the output transistor. Be sure that VOUT does not exceed VIN + 0.3 V to prevent the voltage regulator from being damaged due to inverse current flowing from the VOUT pin through a parasitic diode to the VIN pin. 20 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 3. ON / OFF pin This pin starts and stops the regulator. When the ON / OFF pin is set to the power-off level, the entire internal circuit stops operating, and the built-in Pchannel MOS FET output transistor between the VIN and VOUT pins is turned off, reducing current consumption significantly. Since the S-1135 Series A / B / E / F types have a built-in discharge shunt circuit to discharge the output capacitance, the VOUT pin is forcibly set to VSS level. In the S-1135 Series C / D / G / H types, the VOUT pin is set to VSS level through several hundred k internal divided resistors between the VOUT and VSS pins. Note that the current consumption increases when a voltage of 0.3 V to 1.0 V (Ta = 25C) is applied to the ON / OFF pin. The ON / OFF pin is configured as shown in Figures 21 and 22. In the S-1135 Series A / C / E / G types, the ON / OFF pin is internally pulled up or pulled down to VSS when in the floating status, so the VOUT pin is set to the VSS level. In the S-1135 Series B / D / F / H types, the ON / OFF pin is not internally pulled up or pulled down, so do not use these types with the ON / OFF pin in the floating status. When the ON / OFF pin is not used in the S-1135 Series B / D / F / H types, connect the pin to the VIN pin in the B / D types, and connect it to the VSS pin in the F / H types. Table 11 Logic Type ON / OFF Pin Internal Circuits VOUT Pin Voltage Current Consumption A/B/C/D "H": Power-on Operating Set value ISS1*1 A/B/C/D "L": Power-off Stopped VSS level ISS2 E/F/G/H "H": Power-off Stopped VSS level ISS2 E/F/G/H "L": Power-on Operating Set value ISS1*1 *1. Note that the IC's current consumption increases as much as current flows into the pull-up / pull-down resistor when; the ON / OFF pin is connected to VIN in the A / C type, the ON / OFF pin is connected to VSS in the E / G type (Figure 21). (1) S-1135 Series A / C / E / G Type (2) S-1135 Series B / D / F / H Type VIN VIN E / G type ON / OFF ON / OFF A / C type VSS VSS Figure 21 Figure 22 Seiko Instruments Inc. 21 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 4. Discharge shunt function (S-1135 Series A / B / E / F types) The S-1135 Series A / B / E / F types have a built-in discharge shunt circuit to discharge the output capacitance. When the ON / OFF pin is set to power-off level, turns the output transistor off, and turns the discharge shunt function on so that the output capacitor discharges. These types allow for the VOUT pin reach the VSS level faster than the S-1135 Series C / D / G / H types that does not have a discharge shunt circuit. S-1135 Series Output transistor : OFF *1 VOUT VIN Discharge shunt function : ON *1 ON / OFF Power-off circuit Output capacitance (CL) ON / OFF Pin : Power-off Current flow GND VSS *1. Parasitic diode Figure 23 22 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series 5. Overcurrent protection circuit The S-1135 Series has an overcurrent protection circuit having the characteristics shown in "(1) Output Voltage vs. Output Current (When Load Current Increases) (Ta = 25C)" in " Characteristics (Typical Data)", in order to protect the output transistor against an excessive output current and short circuiting between the VOUT and VSS pins. The current (Ishort) when the output pin is short-circuited is internally set at approx. 100 mA (typ.), and the normal value is restored for the output voltage, if releasing a short circuit once. Caution Using the overcurrent protection circuit is to protect the output transistor from accidental conditions such as short circuited load and the rapid and large current flow in the large capacitor. The overcurrent protection circuit is not suitable for use under the short circuit status or large current flowing (300 mA or more) that last long. 6. Pull-down / pull-up resistor (S-1135 Series A / C / E / G types) In the S-1135 Series A / C / E / G types, the ON / OFF pin is internally pulled up to VIN or pulled down to VSS, so the VOUT pin is in the VSS level when in the floating status. Note that the IC's current consumption increases as much as current flows into the pull-up / pull-down resistor of 2.2 M (typ.) when; the ON / OFF pin is connected to VIN in the A / C type, the ON / OFF pin is connected to VSS in the E / G type. Seiko Instruments Inc. 23 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Precautions * Wiring patterns for the VIN, VOUT and GND pins should be designed so that the impedance is low. When mounting an output capacitor between the VOUT and VSS pin (CL) and a capacitor for stabilizing the input between VIN and VSS pin (CIN), the distance from the capacitors to these pins should be as short as possible. * Note that the output voltage may increase when a series regulator is used at low load current (1.0 mA or less). * Note that the output voltage may increase due to the leakage current from a driver when a series regulator is used at high temperature. * Generally a series regulator may cause oscillation, depending on the selection of external parts. The following conditions are recommended for this IC. However, be sure to perform sufficient evaluation under the actual usage conditions for selection, including evaluation of temperature characteristics. See "(5) Example of Equivalent Series Resistance vs. Output Current Characteristics (Ta = 25C)" in " Reference Data" for the equivalent series resistance (RESR) of the output capacitor. Input capacitor (CIN) : Output capacitor (CL) : 1.0 F or more 1.0 F or more * The voltage regulator may oscillate when the impedance of the power supply is high and the input capacitor is small or an input capacitor is not connected. * If the output capacitance is small, power supply's fluctuation and the characteristics of load fluctuation become worse. Sufficiently evaluate the output voltage's fluctuation with the actual device. * A momentary overshoot may be output when the power supply suddenly increases, and the output capacitance is small. It is therefore important to sufficiently evaluate the output voltage at power application in actual device. * The application conditions for the input voltage, output voltage, and load current should not exceed the package power dissipation. * Do not apply an electrostatic discharge to this IC that exceeds the performance ratings of the built-in electrostatic protection circuit. * In determining the output current, attention should be paid to the output current value specified in Table 10 in " Electrical Characteristics" and footnote *5 of the table. * SII claims no responsibility for any disputes arising out of or in connection with any infringement by products including this IC of patents owned by a third party. 24 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Characteristics (Typical Data) (1) Output Voltage vs. Output Current (When Load Current Increases) (Ta = 25C) 1.0 2.5 0.8 VOUT [V] VOUT = 2.5 V 3.0 VOUT [V] VOUT = 1.0 V 1.2 VIN = 1.3 V 1.5 V 2.0 V 3.0 V 5.5 V 0.6 0.4 0.2 VIN = 2.8 V 3.0 V 3.5 V 4.5 V 5.5 V 2.0 1.5 1.0 0.5 0 0 0 200 300 400 IOUT [mA] 500 100 200 300 400 IOUT [mA] 0 600 VIN = 3.8 V 4.0 V 4.5 V 5.5 V VOUT [V] VOUT = 3.5 V 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 100 Remark 500 100 200 300 400 IOUT [mA] 500 600 In determining the output current, attention should be paid to the following. 1. The minimum output current value and footnote *5 in Table 10 in the " Electrical Characteristics" 2. The package power dissipation 600 (2) Output Voltage vs. Input Voltage (Ta = 25C) VOUT = 1.0 V 1.2 1.0 VOUT [V] VOUT [V] 1.1 IOUT = 1 mA IOUT = 30 mA IOUT = 50 mA IOUT = 100 mA 0.9 0.8 0.7 0.6 0.6 VOUT [V] VOUT = 3.5 V 3.7 3.6 3.5 3.4 3.3 3.2 3.1 3.0 3.0 1.0 1.4 1.8 VIN [V] VOUT = 2.5 V 2.7 2.6 2.5 2.4 2.3 2.2 2.1 2.0 2.0 2.2 2.6 5.0 5.5 IOUT = 1 mA IOUT = 30 mA IOUT = 50 mA IOUT = 100 mA 2.5 3.0 3.5 VIN [V] 4.0 4.5 IOUT = 1 mA IOUT = 30 mA IOUT = 50 mA IOUT = 100 mA 3.5 4.0 4.5 VIN [V] Seiko Instruments Inc. 25 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (3) Dropout Voltage vs. Output Current Vdrop [V] VOUT = 3.5 V 0.20 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0 0 Ta = 85C 25C 50 100 VOUT = 2.5 V 0.20 0.18 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0 0 Vdrop [V] -40C Vdrop [V] VOUT = 1.0 V 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 0 150 200 IOUT [mA] 250 300 250 300 Ta = 85C 25C -40C 50 100 150 200 IOUT [mA] Vdrop [V] (4) Dropout Voltage vs. Set Output Voltage 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 IOUT = 300 mA 150 mA 100 mA 50 mA 1.0 26 1.5 30 mA 2.0 2.5 VOTA [V] 10 mA 3.0 1 mA 3.5 Seiko Instruments Inc. Ta = 85C 25C -40C 50 100 150 200 IOUT [mA] 250 300 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (5) Output Voltage vs. Ambient Temperature VOUT = 1.0 V 1.10 VOUT [V] VOUT [V] 1.05 VOUT = 2.5 V 2.70 2.65 2.60 2.55 2.50 2.45 2.40 2.35 2.30 -40 -25 1.00 0.95 0.90 -40 -25 0 25 Ta [C] 50 75 85 50 75 85 0 25 Ta [C] 50 75 85 VOUT = 3.5 V 3.8 VOUT [V] 3.7 3.6 3.5 3.4 3.3 3.2 -40 -25 0 25 Ta [C] (6) Current Consumption vs. Input Voltage 1 2 3 VIN [V] 25C 4 Ta = 85C 5 6 -40C 1 2 3 VIN [V] 4 25C 5 6 Ta = 85C ISS1 [A] VOUT = 3.5 V 70 60 50 40 30 20 10 0 0 -40C VOUT = 2.5 V 70 60 50 40 30 20 10 0 0 ISS1 [A] Ta = 85C ISS1 [A] VOUT = 1.0 V 70 60 50 40 30 20 10 0 0 25C -40C 1 2 3 VIN [V] 4 5 6 Seiko Instruments Inc. 27 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (7) Ripple Rejection (Ta = 25C) VOUT = 1.0 V VOUT = 2.5 V 100 80 IOUT = 1 mA 60 40 IOUT = 30 mA IOUT = 50 mA IOUT = 100 mA 20 0 10 100 VIN = 3.5 V, CL = 1.0 F Ripple Rejection [dB] Ripple Rejection [dB] VIN = 2.0 V, CL = 1.0 F 1k 10k 100k Frequency [Hz] 100 60 40 20 1M Ripple Rejection [dB] VIN = 4.5 V, CL = 1.0 F 100 IOUT = 1 mA IOUT = 30 mA IOUT = 50 mA 60 40 20 IOUT = 100 mA 0 10 28 100 1k 10k 100k Frequency [Hz] IOUT = 100 mA 0 VOUT = 3.5 V 80 IOUT = 1 mA IOUT = 30 mA IOUT = 50 mA 80 1M Seiko Instruments Inc. 10 100 1k 10k 100k Frequency [Hz] 1M HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Reference Data 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 VOUT [V] 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 VIN [V] VIN [V] VOUT = 3.5 V IOUT = 100 mA, tr = tf = 5.0 s, CL = 1.0 F 3.80 3.75 3.70 VIN 3.65 3.60 3.55 VOUT 3.50 3.45 3.40 -100 -50 0 50 100 150 200 250 300 350 t [s] VOUT = 2.5 V IOUT = 100 mA, tr = tf = 5.0 s, CL = 1.0 F 2.80 2.75 2.70 VIN 2.65 2.60 2.55 VOUT 2.50 2.45 2.40 -100 -50 0 50 100 150 200 250 300 350 t [s] VOUT [V] 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 VOUT [V] VOUT = 1.0 V IOUT = 100 mA, tr = tf = 5.0 s, CL = 1.0 F 1.30 1.25 1.20 1.15 VIN 1.10 1.05 VOUT 1.00 0.95 0.90 -100 -50 0 50 100 150 200 250 300 350 t [s] VIN [V] (1) Transient Response Characteristics when Input (Ta = 25C) (2) Transient Response Characteristics of Load (Ta = 25C) 1.10 1.05 1.00 2.65 50 2.60 0 VOUT -50 0.95 0.90 -100 -50 0 100 VOUT [V] IOUT IOUT [mA] VOUT [V] 1.15 VOUT = 2.5 V VIN = 3.5 V, CL = 1.0 F, CIN = 1.0 F, IOUT = 50 100 mA 150 2.70 2.55 2.50 50 0 VOUT -100 2.45 -150 2.40 -100 -50 0 50 100 150 200 250 300 350 t [s] 100 IOUT -50 IOUT [mA] VOUT = 1.0 V VIN = 2.0 V, CL = 1.0 F, CIN = 1.0 F, IOUT = 50 100 mA 150 1.20 -100 -150 50 100 150 200 250 300 350 t [s] VOUT = 3.5 V VIN = 4.5 V, CL = 1.0 F, CIN = 1.0 F, IOUT = 50 100 mA 150 3.70 100 IOUT 50 3.60 3.55 3.50 0 VOUT -50 -100 3.45 3.40 -100 -50 0 IOUT [mA] VOUT [V] 3.65 -150 50 100 150 200 250 300 350 t [s] Seiko Instruments Inc. 29 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (3) Transient Response Characteristics of ON / OFF Pin (Ta = 25C) 0 -1 VOUT VOUT [V] 1 1.2 0.8 5 2 VON / OFF 1.6 VON / OFF [V] VOUT [V] 2.0 VOUT = 2.5 V VIN = 3.5 V, tr = 5.0 s, CL = 1.0 F, CIN = 1.0 F, IOUT = 100 mA 6 6 -2 1 -3 0 50 100 t [s] 150 0 2 0 0 2 3 0.4 -50 4 VON / OFF 4 -4 -50 200 -2 VOUT VON / OFF [V] VOUT = 1.0 V VIN = 2.0 V, tr = 5.0 s, CL = 1.0 F, CIN = 1.0 F, IOUT = 100 mA 3 2.4 -6 0 50 100 t [s] 150 200 5 VON / OFF 4 VOUT 0 2 VOUT [V] 4 3 2 -2 1 -4 VON / OFF [V] VOUT = 3.5 V VIN = 4.5 V, tr = 5.0 s, CL = 1.0 F, CIN = 1.0 F, IOUT = 100 mA 6 6 -6 0 -50 0 50 100 t [s] 150 200 (4) Output Capacitance vs. Characteristics of Discharge Time (Ta = 25C) S-1135 Series A / B type (with discharge shunt function) tDSC [ms] VIN = VOUT + 1.0 V, IOUT = no load VON / OFF = VOUT + 1.0 V VSS, tf = 1 s 2.5 VOUT(s) = 1.0 V 2.0 2.5 V 3.5 V 1.5 1 s VON / OFF 1.0 VSS 0.5 tDSC VOUT 0 0 2 4 6 CL [F] 8 10 12 VOUT x 10% VIN = VOUT + 1.0 V VON / OFF = VOUT + 1.0 V VSS Figure 24 30 Seiko Instruments Inc. Measurement Condition of Discharge Time HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (5) Example of Equivalent Series Resistance vs. Output Current Characteristics (Ta = 25C) CL : TAIYO YUDEN TMK316BJ105KD (1.0 F) CIN = CL = 1.0 F 100 RESR [] VIN CIN Stable VOUT S-1135 Series CL ON / OFF 0 0.1 VSS RESR 300 IOUT [mA] Seiko Instruments Inc. 31 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series Marking Specifications (1) SOT-89-5 SOT-89-5 Top view 1 : Product code (Refer to Product name vs. Product code) : Lot number (4) (5) (6) 4 (1) (2) (3) 5 (1) to (3) (4) to (6) 2 3 Product name vs. Product code (a) S-1135 Series A type (b) S-1135 Series B type Product code Product code Product Name (1) (2) (3) (1) (2) (3) S-1135A10-U5T1x S E A S-1135B10-U5T1x S G A S-1135A11-U5T1x S E B S-1135B11-U5T1x S G B S-1135A12-U5T1x S E C S-1135B12-U5T1x S G C S-1135A13-U5T1x S E D S-1135B13-U5T1x S G D S-1135A14-U5T1x S E E S-1135B14-U5T1x S G E S-1135A15-U5T1x S E F S-1135B15-U5T1x S G F S-1135A16-U5T1x S E G S-1135B16-U5T1x S G G S-1135A17-U5T1x S E H S-1135B17-U5T1x S G H S-1135A18-U5T1x S E I S-1135B18-U5T1x S G I S-1135A1J-U5T1x S E J S-1135B1J-U5T1x S G J S-1135A19-U5T1x S E K S-1135B19-U5T1x S G K S-1135A20-U5T1x S E L S-1135B20-U5T1x S G L S-1135A21-U5T1x S E M S-1135B21-U5T1x S G M S-1135A22-U5T1x S E N S-1135B22-U5T1x S G N S-1135A23-U5T1x S E O S-1135B23-U5T1x S G O S-1135A24-U5T1x S E P S-1135B24-U5T1x S G P S-1135A25-U5T1x S E Q S-1135B25-U5T1x S G Q S-1135A26-U5T1x S E R S-1135B26-U5T1x S G R S-1135A27-U5T1x S E S S-1135B27-U5T1x S G S S-1135A28-U5T1x S E T S-1135B28-U5T1x S G T S-1135A2J-U5T1x S E U S-1135B2J-U5T1x S G U S-1135A29-U5T1x S E V S-1135B29-U5T1x S G V S-1135A30-U5T1x S E W S-1135B30-U5T1x S G W S-1135A31-U5T1x S E X S-1135B31-U5T1x S G X S-1135A32-U5T1x S E Y S-1135B32-U5T1x S G Y S-1135A33-U5T1x S E Z S-1135B33-U5T1x S G Z S-1135A34-U5T1x S E 2 S-1135B34-U5T1x S G 2 S-1135A10-U5T1x S E 3 S-1135B35-U5T1x S G 3 Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Product Name 32 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (c) S-1135 Series C type (d) S-1135 Series D type Product code Product code Product Name (1) (2) (3) (1) (2) (3) S-1135C10-U5T1x V A A S-1135D10-U5T1x V B A S-1135C11-U5T1x V A B S-1135D11-U5T1x V B B S-1135C12-U5T1x V A C S-1135D12-U5T1x V B C S-1135C13-U5T1x V A D S-1135D13-U5T1x V B D S-1135C14-U5T1x V A E S-1135D14-U5T1x V B E S-1135C15-U5T1x V A F S-1135D15-U5T1x V B F S-1135C16-U5T1x V A G S-1135D16-U5T1x V B G S-1135C17-U5T1x V A H S-1135D17-U5T1x V B H S-1135C18-U5T1x V A I S-1135D18-U5T1x V B I S-1135C1J-U5T1x V A J S-1135D1J-U5T1x V B J S-1135C19-U5T1x V A K S-1135D19-U5T1x V B K S-1135C20-U5T1x V A L S-1135D20-U5T1x V B L S-1135C21-U5T1x V A M S-1135D21-U5T1x V B M S-1135C22-U5T1x V A N S-1135D22-U5T1x V B N S-1135C23-U5T1x V A O S-1135D23-U5T1x V B O S-1135C24-U5T1x V A P S-1135D24-U5T1x V B P S-1135C25-U5T1x V A Q S-1135D25-U5T1x V B Q S-1135C26-U5T1x V A R S-1135D26-U5T1x V B R S-1135C27-U5T1x V A S S-1135D27-U5T1x V B S S-1135C28-U5T1x V A T S-1135D28-U5T1x V B T S-1135C2J-U5T1x V A U S-1135D2J-U5T1x V B U S-1135C29-U5T1x V A V S-1135D29-U5T1x V B V S-1135C30-U5T1x V A W S-1135D30-U5T1x V B W S-1135C31-U5T1x V A X S-1135D31-U5T1x V B X S-1135C32-U5T1x V A Y S-1135D32-U5T1x V B Y S-1135C33-U5T1x V A Z S-1135D33-U5T1x V B Z S-1135C34-U5T1x V A 2 S-1135D34-U5T1x V B 2 S-1135C35-U5T1x V A 3 S-1135D35-U5T1x V B 3 Remark 1. Please contact our sales office for products with specifications other than the above. 2. x: G or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Product Name Seiko Instruments Inc. 33 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (2) SOT-23-5 SOT-23-5 Top view 5 (1) to (3) (4) 4 : Product code (Refer to Product name vs. Product code) : Lot number (1) (2) (3) (4) 1 2 3 Product name vs. Product code (a) S-1135 Series A type Product Name (b) S-1135 Series B type (1) Product code (2) (3) Product Name (1) Product code (2) (3) S-1135A10-M5T1y S E A S-1135B10-M5T1y S S-1135A11-M5T1y S E B S-1135B11-M5T1y S S-1135A12-M5T1y S E C S-1135B12-M5T1y S S-1135A13-M5T1y S E D S-1135B13-M5T1y S S-1135A14-M5T1y S E E S-1135B14-M5T1y S S-1135A15-M5T1y S E F S-1135B15-M5T1y S S-1135A16-M5T1y S E G S-1135B16-M5T1y S S-1135A17-M5T1y S E H S-1135B17-M5T1y S S-1135A18-M5T1y S E I S-1135B18-M5T1y S S-1135A1J-M5T1y S E J S-1135B1J-M5T1y S S-1135A19-M5T1y S E K S-1135B19-M5T1y S S-1135A20-M5T1y S E L S-1135B20-M5T1y S S-1135A21-M5T1y S E M S-1135B21-M5T1y S S-1135A22-M5T1y S E N S-1135B22-M5T1y S S-1135A23-M5T1y S E O S-1135B23-M5T1y S S-1135A24-M5T1y S E P S-1135B24-M5T1y S S-1135A25-M5T1y S E Q S-1135B25-M5T1y S S-1135A26-M5T1y S E R S-1135B26-M5T1y S S-1135A27-M5T1y S E S S-1135B27-M5T1y S S-1135A28-M5T1y S E T S-1135B28-M5T1y S S-1135A2J-M5T1y S E U S-1135B2J-M5T1y S S-1135A29-M5T1y S E V S-1135B29-M5T1y S S-1135A30-M5T1y S E W S-1135B30-M5T1y S S-1135A31-M5T1y S E X S-1135B31-M5T1y S S-1135A32-M5T1y S E Y S-1135B32-M5T1y S S-1135A33-M5T1y S E Z S-1135B33-M5T1y S S-1135A34-M5T1y S E 2 S-1135B34-M5T1y S S-1135A35-M5T1y S E 3 S-1135B35-M5T1y S Remark 1. Please contact our sales office for products with specifications other than the above. 2. y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. 34 Seiko Instruments Inc. G G G G G G G G G G G G G G G G G G G G G G G G G G G G A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 2 3 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (c) S-1135 Series C type (d) S-1135 Series D type Product code Product code Product Name (1) (2) (3) (1) (2) (3) S-1135C10-M5T1y V A A S-1135D10-M5T1y V B A S-1135C11-M5T1y V A B S-1135D11-M5T1y V B B S-1135C12-M5T1y V A C S-1135D12-M5T1y V B C S-1135C13-M5T1y V A D S-1135D13-M5T1y V B D S-1135C14-M5T1y V A E S-1135D14-M5T1y V B E S-1135C15-M5T1y V A F S-1135D15-M5T1y V B F S-1135C16-M5T1y V A G S-1135D16-M5T1y V B G S-1135C17-M5T1y V A H S-1135D17-M5T1y V B H S-1135C18-M5T1y V A I S-1135D18-M5T1y V B I S-1135C1J-M5T1y V A J S-1135D1J-M5T1y V B J S-1135C19-M5T1y V A K S-1135D19-M5T1y V B K S-1135C20-M5T1y V A L S-1135D20-M5T1y V B L S-1135C21-M5T1y V A M S-1135D21-M5T1y V B M S-1135C22-M5T1y V A N S-1135D22-M5T1y V B N S-1135C23-M5T1y V A O S-1135D23-M5T1y V B O S-1135C24-M5T1y V A P S-1135D24-M5T1y V B P S-1135C25-M5T1y V A Q S-1135D25-M5T1y V B Q S-1135C26-M5T1y V A R S-1135D26-M5T1y V B R S-1135C27-M5T1y V A S S-1135D27-M5T1y V B S S-1135C28-M5T1y V A T S-1135D28-M5T1y V B T S-1135C2J-M5T1y V A U S-1135D2J-M5T1y V B U S-1135C29-M5T1y V A V S-1135D29-M5T1y V B V S-1135C30-M5T1y V A W S-1135D30-M5T1y V B W S-1135C31-M5T1y V A X S-1135D31-M5T1y V B X S-1135C32-M5T1y V A Y S-1135D32-M5T1y V B Y S-1135C33-M5T1y V A Z S-1135D33-M5T1y V B Z S-1135C34-M5T1y V A 2 S-1135D34-M5T1y V B 2 S-1135C35-M5T1y V A 3 S-1135D35-M5T1y V B 3 Remark 1. Please contact our sales office for products with specifications other than the above. 2. y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Product Name Seiko Instruments Inc. 35 HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (3) HSNT-6A HSNT-6A Top view (1) (2) (3) 3 (4) (5) (6) 2 (7) (8) (9) 1 6 (1) to (3) (4) (5) to (9) : Product code (Refer to Product name vs. Product code) : Blank : Lot number 5 4 Product name vs. Product code (a) S-1135 Series A type (b) S-1135 Series B type Product code Product code Product Name (1) (2) (3) (1) (2) (3) S-1135A10-A6T1y S E A S-1135B10-A6T1y S G A S-1135A11-A6T1y S E B S-1135B11-A6T1y S G B S-1135A12-A6T1y S E C S-1135B12-A6T1y S G C S-1135A13-A6T1y S E D S-1135B13-A6T1y S G D S-1135A14-A6T1y S E E S-1135B14-A6T1y S G E S-1135A15-A6T1y S E F S-1135B15-A6T1y S G F S-1135A16-A6T1y S E G S-1135B16-A6T1y S G G S-1135A17-A6T1y S E H S-1135B17-A6T1y S G H S-1135A18-A6T1y S E I S-1135B18-A6T1y S G I S-1135A1J-A6T1y S E J S-1135B1J-A6T1y S G J S-1135A19-A6T1y S E K S-1135B19-A6T1y S G K S-1135A20-A6T1y S E L S-1135B20-A6T1y S G L S-1135A21-A6T1y S E M S-1135B21-A6T1y S G M S-1135A22-A6T1y S E N S-1135B22-A6T1y S G N S-1135A23-A6T1y S E O S-1135B23-A6T1y S G O S-1135A24-A6T1y S E P S-1135B24-A6T1y S G P S-1135A25-A6T1y S E Q S-1135B25-A6T1y S G Q S-1135A26-A6T1y S E R S-1135B26-A6T1y S G R S-1135A27-A6T1y S E S S-1135B27-A6T1y S G S S-1135A28-A6T1y S E T S-1135B28-A6T1y S G T S-1135A2J-A6T1y S E U S-1135B2J-A6T1y S G U S-1135A29-A6T1y S E V S-1135B29-A6T1y S G V S-1135A30-A6T1y S E W S-1135B30-A6T1y S G W S-1135A31-A6T1y S E X S-1135B31-A6T1y S G X S-1135A32-A6T1y S E Y S-1135B32-A6T1y S G Y S-1135A33-A6T1y S E Z S-1135B33-A6T1y S G Z S-1135A34-A6T1y S E 2 S-1135B34-A6T1y S G 2 S-1135A35-A6T1y S E 3 S-1135B35-A6T1y S G 3 Remark 1. Please contact our sales office for products with specifications other than the above. 2. y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Product Name 36 Seiko Instruments Inc. HIGH RIPPLE-REJECTION LOW DROPOUT MIDDLE OUTPUT CURRENT CMOS VOLTAGE REGULATOR Rev.2.0_00 S-1135 Series (c) S-1135 Series C type (d) S-1135 Series D type Product code Product code Product Name (1) (2) (3) (1) (2) (3) S-1135C10-A6T1y V A A S-1135D10-A6T1y V B A S-1135C11-A6T1y V A B S-1135D11-A6T1y V B B S-1135C12-A6T1y V A C S-1135D12-A6T1y V B C S-1135C13-A6T1y V A D S-1135D13-A6T1y V B D S-1135C14-A6T1y V A E S-1135D14-A6T1y V B E S-1135C15-A6T1y V A F S-1135D15-A6T1y V B F S-1135C16-A6T1y V A G S-1135D16-A6T1y V B G S-1135C17-A6T1y V A H S-1135D17-A6T1y V B H S-1135C18-A6T1y V A I S-1135D18-A6T1y V B I S-1135C1J-A6T1y V A J S-1135D1J-A6T1y V B J S-1135C19-A6T1y V A K S-1135D19-A6T1y V B K S-1135C20-A6T1y V A L S-1135D20-A6T1y V B L S-1135C21-A6T1y V A M S-1135D21-A6T1y V B M S-1135C22-A6T1y V A N S-1135D22-A6T1y V B N S-1135C23-A6T1y V A O S-1135D23-A6T1y V B O S-1135C24-A6T1y V A P S-1135D24-A6T1y V B P S-1135C25-A6T1y V A Q S-1135D25-A6T1y V B Q S-1135C26-A6T1y V A R S-1135D26-A6T1y V B R S-1135C27-A6T1y V A S S-1135D27-A6T1y V B S S-1135C28-A6T1y V A T S-1135D28-A6T1y V B T S-1135C2J-A6T1y V A U S-1135D2J-A6T1y V B U S-1135C29-A6T1y V A V S-1135D29-A6T1y V B V S-1135C30-A6T1y V A W S-1135D30-A6T1y V B W S-1135C31-A6T1y V A X S-1135D31-A6T1y V B X S-1135C32-A6T1y V A Y S-1135D32-A6T1y V B Y S-1135C33-A6T1y V A Z S-1135D33-A6T1y V B Z S-1135C34-A6T1y V A 2 S-1135D34-A6T1y V B 2 S-1135C35-A6T1y V A 3 S-1135D35-A6T1y V B 3 Remark 1. Please contact our sales office for products with specifications other than the above. 2. y: S or U 3. Please select products of environmental code = U for Sn 100%, halogen-free products. Product Name Seiko Instruments Inc. 37 4.50.1 1.50.1 1.60.2 5 1 4 2 3 1.50.1 1.50.1 0.40.05 0.3 0.40.1 0.40.1 45 0.450.1 No. UP005-A-P-SD-1.1 TITLE SOT895-A-PKG Dimensions UP005-A-P-SD-1.1 No. SCALE UNIT mm Seiko Instruments Inc. 4.00.1(10 pitches : 40.00.2) o1.5 +0.1 -0 2.00.05 5 max. o1.5 +0.1 -0 0.30.05 8.00.1 2.00.1 4.750.1 3 2 1 4 5 Feed direction No. UP005-A-C-SD-1.1 TITLE SOT895-A-Carrier Tape UP005-A-C-SD-1.1 No. SCALE UNIT mm Seiko Instruments Inc. 16.5max. 13.00.3 Enlarged drawing in the central part (60) (60) No. UP005-A-R-SD-1.1 TITLE SOT895-A-Reel No. UP005-A-R-SD-1.1 SCALE QTY. UNIT mm Seiko Instruments Inc. 1,000 2.90.2 1.90.2 4 5 1 2 +0.1 0.16 -0.06 3 0.950.1 0.40.1 No. MP005-A-P-SD-1.2 TITLE No. SOT235-A-PKG Dimensions MP005-A-P-SD-1.2 SCALE UNIT mm Seiko Instruments Inc. 4.00.1(10 pitches:40.00.2) +0.1 o1.5 -0 2.00.05 +0.2 o1.0 -0 0.250.1 4.00.1 1.40.2 3.20.2 3 2 1 4 5 Feed direction No. MP005-A-C-SD-2.1 TITLE SOT235-A-Carrier Tape No. MP005-A-C-SD-2.1 SCALE UNIT mm Seiko Instruments Inc. 12.5max. 9.00.3 Enlarged drawing in the central part o130.2 (60) (60) No. MP005-A-R-SD-1.1 SOT235-A-Reel TITLE No. MP005-A-R-SD-1.1 SCALE QTY. UNIT mm Seiko Instruments Inc. 3,000 1.960.05 1.780.05 6 1 5 0.5 4 2 3 0.5 0.5 0.120.04 0.480.02 0.220.05 The heatsink of back side has different electric potential depending on the product. Confirm specifications of each product. Do not use it as the function of electrode. No. PJ006-A-P-SD-2.0 TITLE HSNT-6A-A-PKG Dimensions PJ006-A-P-SD-2.0 No. SCALE UNIT mm Seiko Instruments Inc. +0.1 5 4.00.1 2.00.05 o1.5 -0 o0.50.1 2.250.05 0.250.05 0.650.05 4.00.1 3 21 0.5 0.5 0.5 0.5 0.5 0.5 4 5 6 Feed direction No. PJ006-A-C-SD-1.0 TITLE HSNT-6A-A-Carrier Tape PJ006-A-C-SD-1.0 No. SCALE UNIT mm Seiko Instruments Inc. 12.5max. 9.00.3 Enlarged drawing in the central part o130.2 (60) (60) No. PJ006-A-R-SD-1.0 HSNT-6A-A-Reel TITLE PJ006-A-R-SD-1.0 No. SCALE UNIT QTY. mm Seiko Instruments Inc. 5,000 Land Recommendation 0.5 0.7 0.7 0.35 0.35 0.3 1.4 2.1 Stencil Opening 0.5 0.2 0.8 0.8 0.3 0.2 1.6 2.0 TITLE HSNT-6A-A-Land &Stencil Opening PJ006-A-LM-SD-1.0 No. SCALE UNIT mm No. PJ006-A-LM-SD-1.0 Seiko Instruments Inc. www.sii-ic.com * * * * * * * The information described herein is subject to change without notice. Seiko Instruments Inc. is not responsible for any problems caused by circuits or diagrams described herein whose related industrial properties, patents, or other rights belong to third parties. The application circuit examples explain typical applications of the products, and do not guarantee the success of any specific mass-production design. When the products described herein are regulated products subject to the Wassenaar Arrangement or other agreements, they may not be exported without authorization from the appropriate governmental authority. Use of the information described herein for other purposes and/or reproduction or copying without the express permission of Seiko Instruments Inc. is strictly prohibited. The products described herein cannot be used as part of any device or equipment affecting the human body, such as exercise equipment, medical equipment, security systems, gas equipment, or any apparatus installed in airplanes and other vehicles, without prior written permission of Seiko Instruments Inc. The products described herein are not designed to be radiation-proof. Although Seiko Instruments Inc. exerts the greatest possible effort to ensure high quality and reliability, the failure or malfunction of semiconductor products may occur. The user of these products should therefore give thorough consideration to safety design, including redundancy, fire-prevention measures, and malfunction prevention, to prevent any accidents, fires, or community damage that may ensue.