IGD515EI Data Sheet & Application Manual Intelligent Gate Driver Cores for IGBTs and Power MOSFETs Description The intelligent gate driver cores of the IGD515EI series are singlechannel drive components designed for IGBTs and power MOSFETs. They were developed specifically for the precise and reliable driving and protection of high-power modules, high-voltage modules, series and parallel circuits. The drive information and the status acknowledgement of IGD515EI drivers are transmitted via external fiber-optic links. The drivers contain an integrated DC/DC converter with a high isolation test voltage. Special logic functions allow the implementation of reliable series circuits with IGBTs or power MOSFETs. Product Highlights [ Suitable for IGBTs and power MOSFETs [ Protect the power transistors [ Extremely reliable, long service life [ High gate current of 15A [ Electrical isolation 5000Vac [ Series connection functions [ Monitoring of power supply and self-monitoring [ Switching frequency DC to 100kHz [ Duty cycle: 0... 100% [ Fiber-optic links make long drive cables possible [ Shortens development time IGBT-Driver.com Applications [ Traction [ Power Converters [ Motor Drives [ Switched-mode power supplies [ Radiology and laser technology [ High-frequency applications [ Wind power converters [ Medium-voltage converters [ Research Page 1 IGD515EI Data Sheet & Application Manual Absolute Maximum Ratings Parameter Test conditions min max Unit Supply voltage Vcc Logic input voltage Gate peak current Iout Test voltage (50Hz/1min) Operating temperature Storage temperature Pin 10 to pin 9 -0.5 Vdc Vdc A Vac C C 16 5 -15 +15 5000 -40 +85 -40 +90 (see note 5) Pin 25 INxx to output stages Pin Designation Pin Desig. Function Pin Desig. Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Power supply GND Power supply GND Power supply GND Power supply GND Not present Not present Not present Not present Power supply GND Power supply plus terminal Not present Not present Not present Not present Not connected Not connected Not connected Not connected 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 Acknowledgement pulse capacitor Status output signal series-connected IGBT mode Inverse input Input signal from FOL 5V power supply for FOL GND for FOL Not present Not present Not present Not present Gate driver output Virtual common Blocking capacitor Emitter / Source External reference Blocking time capacitor VCE measurement GND GND GND GND GND Vcc NC NC NC NC Cq SO SDOSA INV INPUT +5V IGND G COM Cs E REF Cb ME Legend for terminal assignment: Pins with the designation "not connected" are physically present but must not be connected to an electrical potential. Pins with the designation "not present" are not physically present. The abbreviation "FOL" stands for Fiber-Optic Link. Page 2 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual Block Diagram SO 35 19 ME Voltage Monitoring +5V 31 Vce Monitoring 21 Ref +Viso 5VRegulator SDOSA 34 Protection Logic INPUT 32 Driver 25 G Interface Logic Cq 36 INV 33 22 E Timing Control 20 Cb IGND 30 VCC 10 Electrical Isolation +Viso GND 9 23 Cs GND 4 GND 3 GND 2 24 COM PWM Controller GND 1 IGD515EI Fig. 1 Block and connection diagram of the IGD515EI IGBT-Driver.com Page 3 IGD515EI Data Sheet & Application Manual Mechanical Dimensions Layout overview (component side) Grid Solder pads Drill holes 2.54 O 1.6 O 0.9 All dimensions are in mm Fig. 2 Mechanical dimensions and printed circuit layout Case & Coating Component Material Case product Coating mass Noryl (PPE mod.), non-halogenate flame retardants Polyurethane base, temperature-cycle resistant Page 4 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual General Characteristics Quality Standard Manufacturing ISO9001 certified Reliability Standard MTBF MIL HDBK 217F (see Note 12) Thermal Characteristics Test Conditions Operating temperature Storage temperature typ units > 2,000,000 hours min max units -40 -40 +85 +90 C C min typ max Electrical Characteristics Power Supply Test Conditions Supply voltage Vcc (see Note 1) Supply current Icc (see Note 2) Max. supply current Icc Output power DC/DC converter Efficiency Turn-on threshold Vth Hysteresis on-/off (see Note 4) Coupling capacitance Cio Pin 10 to pin 9 Without load 12 15 50 (see Note 3 & 11) (see Note 3 & 11) nternal DC/DC converter 85 10 0.6 24 (see Note 6) 450 6 Logic Inputs Test Conditions Max. input voltage Vin Input voltage for logic "1" Input voltage for logic "0" (see Note 5) (see Note 7) (see Note 7) Vce-Monitoring Test Conditions min typ max Inputs ME to E/COM -0.5 Vcc IGBT-Driver.com min 16 3.8 typ max 5 0.9 units Vdc mA mA W % Vdc Vdc pF units Vdc Vdc Vdc units Vdc Page 5 IGD515EI Data Sheet & Application Manual Electrical Characteristics (Continuation) Timing Characteristics Test Conditions Delay time input to output Delay time status output Turn-on tpd(on) (see Note 14) Turn-off tpd(off) (see Note 14) Pin 35 (see Note 16) Outputs Test Conditions Output Output Output Output Output Output current Iout (see Note 8) Pin rise time tr(out) (see Note 9) fall time tf(out) (see Note 9) current SO Pin voltage rating SO Pin current +5V Pin Electrical Isolation 25 min 100 100 75 min -15 35 35 31 Test Conditions Operating voltage (see Note 10) Continuous or repeated Test voltage (50Hz/1min) (see Note 17) Partial discharge extinction volt. IEC270 (see Note 15) typ max min 2500 ns ns ns typ max 40 40 units +15 90 40 30 units A ns ns mA V mA typ max units 2500 5000 V Vaceff Vpeak All data refer to +25C and Vcc = 15V unless otherwise specified Footnotes to the key data 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) At a supply voltage greater than 16V, the open-circuit voltages on the two output sides of the DC/DC converter may exceed 18V. This can lead to the destruction of the driver and protection circuits on the output side. Only internal consumption of the drivers, static. If the specified power consumption is exceeded, this indicates an overload of the DC/DC converter. It should be noted that these DC/DC converters are not protected against overload. The turn-off threshold is lower than the turn-on threshold by the magnitude of the hysteresis. The turn-on and turn-off thresholds allow the drivers to be run at operating voltages of 12V to 15V and cannot be changed. This refers to the logic inputs INPUT (Pin 32), INV (Pin 33) and SDOSA (Pin 34). Coupling capacitance of the DC/DC converter. Guaranteed logic level for the logic inputs INPUT (Pin 32), INV (Pin 33) and SDOSA (Pin 34), of which only INPUT (Pin 32) has a Schmitt trigger characteristic. The gate current must be limited to its maximum value by a gate resistor. At a load of 1F in series with 2. Maximum continuous or repeatedly-applied DC voltage or peak value of the repeatedly-applied AC voltage between the power supply inputs and all other terminals. However, types that have been measured and selected for higher partial-discharge voltages are also available (see Note 15). The output power of the DC/DC converter is 6W, of which about 1W must be used for the driver's own supply and for the fiber-optic links. This leaves another 5W for driving the power Page 6 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual 12) 13) 14) 15) 16) 17) semiconductors. However, some FOLs require even more power, in which case the power available for driving is reduced. The MTBF (mean time between failures) is calculated to MIL HDBK 217F at an ambient temperature of 40C, a typical load and when the driver is exposed to a current of air. Further information on reliability may be obtained from CONCEPT upon request. The application-specific self-heating of the drivers - especially at high load - must be taken into account. Transit time from pin 32 (INPUT) to pin 25 (G) only within the driver, without external fiber-optic links. The partial discharge is not measured for the standard types. For main power applications, a sufficient safety margin exists between the typical operating voltage of < 600Vdc and the partial discharge extinction voltage of typically about 3000Vpeak. Tested and selected types with guaranteed partial-discharge immunity can be supplied for applications with maximum requirements and higher operating voltages (such as railroad applications). Transit time from a turn-on or turn-off edge of the input signal at pin 32 (INPUT) to the first edge of the acknowledgement at pin 35 (SO) only within the driver, without external fiber-optic links. The transit time to pin 35 (SO) within the driver after a protection function responds is even shorter. The test voltage of 5000Vac(rms)/50Hz may be applied only once during a minute. It should be noted that with this (strictly speaking obsolete) test method, some (minor) damage occurs to the isolation layers due to the partial discharge. Consequently, this test is not performed at CONCEPT as a series test. In the case of repeated isolation tests (e.g. module test, equipment test, system test) the subsequent tests should be performed with a lower test voltage: the test voltage is reduced by 500V for each additional test. The more modern if more elaborate partial-discharge measurement is better suited than such test methods as it is almost entirely non-destructive. Functional Description Overview components are required in the control circuit and in the power section. The intelligent drivers of the IGD515EI series are universal drive modules designed for power MOSFETs and IGBTs in switching operation. Reliable operation The IGD515EI drivers are eminently suited for large modules or for a number of transistors connected in parallel as well as for high-frequency applications. In conjunction with a pair of fiber-optic links (FOLs), the intelligent drivers of the IGD515EI series represent a complete solution for all driving and protection problems associated with power MOSFET and IGBT power stages. Almost no other IGBT-Driver.com Gate driving with a positive and negative control voltage (between 12V and 15V depending on the selected supply voltage) allows reliable operation of IGBT modules of any size from any manufacturer. Thanks to the great interference immunity attained by means of the negative gate voltage, a number of power MOSFET or IGBT modules can be connected in parallel without the user having to worry about parasitic switching operations or oscillations. Page 7 IGD515EI Data Sheet & Application Manual The components contain an overcurrent and short-circuit protection circuit for the power transistors, a feed monitoring function, a status acknowledgement, a mode for brake operation, a mode for series and parallel circuits as well as an electrically-isolated supply for the drive electronics via an integrated DC/DC converter. Genuine electrical isolation The outstanding electrical isolation of up to 2500V operating voltage between the control and power sections predestine these drive modules for applications in which large potential differences and large potential jumps occur between the power section and the control electronics. Application benefits Reliable power stages can be realized with power MOSFETs or IGBTs within an extremely short time by using these driver modules. The high drive power allows simple driving of the largest power semiconductor modules and parallel circuits. The high isolation test-voltage allows high-voltage IGBTs and seriesconnected transistors to be driven. clocked power supplies, RF converters and resonance converters. These drivers have been manufactured by CONCEPT on the basis of many years of experience in producing intelligent drivers for power MOSFETs and IGBTs. Short-circuit and overvoltage protection One of the basic functions of the intelligent drivers of the IGD515EI series is to ensure reliable protection of the driven power transistors against overcurrent and short circuit. The current measurement is based on determining the drain-source or collector-emitter voltage at the turned-on transistor. After a threshold defined by the user has been exceeded, the power transistor is turned off and remains blocked in this condition for a defined minimum time (in normal mode). When this time has elapsed, the transistor is released again. This protection concept can be used to protect IGBTs simply and reliably without the need for additional components in the power path. The integrated DC/DC converter allows a simple power-supply concept: a single 15V feed is sufficient to supply any (large) number of drivers. The short transit times of the drivers of the IGD515EI series - in conjunction with broadband fiber-optic links - also allow them to be used in high-frequency Page 8 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual Layout of the terminals The terminal pins of the drive modules in the IGD515EI series are configured so that the layout can be kept simple. A spacing of 45 mm is maintained between the supply pins and the power potential! Note In the following, the abbreviation "FOL" will be used for the term "fiber-optic link". This refers to a component of a FOL connection, such as a fiber-optic transmitter, a fiber-optic receiver or the entire FOL connection consisting of the fiber-optic transmitter, fiber-optic wire and fiber-optic receiver. Pins 1,2,3,4,9 and 10 GND and Vcc These pins are used for the power supply of the driver module. The nominal feed voltage is between 12V and 15V. To ensure reliable starting of the integrated DC/DC converter, a low-inductance electrolytic capacitor with high ripple current must be placed in the immediate vicinity of pins 9 and 10. The capacitance of this capacitor must not be less than that of the capacitor connected to Cs (Pin 23). The current consumption of the DC/DC converter is determined by the number of driven transistors, their gate capacitance and by the clock frequency. Thanks to the high isolation of the feed terminals with respect to all other pins, the drivers of the IGD515EI series can be supplied by a potential of any size. IGBT-Driver.com The internal turn-on thresholds are designed so that 12V operation is also possible. This is particularly useful for operating transistors that have very high short-circuit currents at higher gate voltages (low saturation types). It should be noted that the drivers themselves are not protected against overload. A short circuit between the gate and the emitter terminal, caused by a defective power semiconductor, for example, can lead to thermal destruction of the driver. Pin 25 - Output Gate Pin 25 is the driver output for driving the gate. Driving is from 12V to 15V, depending on the supply voltage, but also without a negative gate voltage depending on the application and the power transistors used (see description of pin 24, COM). The output stages of the drivers of the IGD515EI series are very ruggedly dimensioned. The maximum permissible gate charging current is 15A; this allows the largest IGBT and power MOSFET modules to be driven. A number of power modules connected in parallel can also be driven directly. The charging current must be limited by an external gate resistor. It should be noted that when the gate is driven with a voltage, the total voltage rise must be considered. The gate of the power transistor must be connected to pin 25 by means of a lead of minimum length. A gate circuit with two gate resistors and a diode can be used to set the switching speeds at turnon and at turn-off independently of each other (see Fig. 3). Page 9 IGD515EI Data Sheet & Application Manual It is mandatory to connect zener diodes immediately between the gate and emitter for IGBTs (connected in antiseries). Their zener voltage must correspond exactly to the selected gate voltage (12V to 15V) (see Fig. 3). They prevent the gate voltage from increasing due to parasitic effects (such as the Miller effect) to a value that is higher than the rated gate voltage. An excessively high gate voltage increases the short-circuit current to an overproportional extent and IGD515EI 25 22 G E Fig. 3 Asymmetrical gate resistors can lead to destruction of the power semiconductors. A sufficiently low-resistance termination of the gate is also ensured by the driver module when this is not supplied with the operating voltage. Pin 22 - Emitter terminal This pin should be connected to the emitter or source terminal of the power transistor. The connection must be as short as possible and must run directly to the emitter or source terminal of the power element. This pin should be used Page 10 for modules with an auxiliary emitter or auxiliary source. It is also used as a basis for the reference, that should be connected as directly as possible to pin 22 of the driver module. If the connections between a driver of the IGD515EI series and a power transistor are set up via connecting leads, then these should not exceed a length of 10 cm. The leads for the gate, emitter and the measuring pin (collector or drain terminal) should be run to each transistor in twisted form. Pin 19 - Terminal ME This pin is used to measure the voltage drop at the turned-on power transistor in order to ensure protection against short circuit and overload. It should be noted that it must never be connected directly to the drain or collector of the power transistor. To protect the measurement terminal from the high drain or collector voltage of the turned-off power element, a circuit with a high-blocking diode (Dme) or several diodes of the 1N4007 type connected in series should be included (see Fig. 4). It is absolutely recommended to overdimension these diodes in terms of voltage. A pull-up resistor integrated in the driver module ensures that a current flows through the measurement diode (DMe), the resistor (Rme) and the power transistor when the latter is turned on. A potential is then present at the measurement input ME that corresponds to the forward voltage of the turned-on transistor plus the diode forward voltage and the voltage drop at Rme. Rme attenuates the reverse-current peaks of INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual the measurement diode Dme and should have a value of about 68. It should be noted that the power transistors do not turn on immediately. It can take several microseconds for them to switch through fully, especially with IGBTs. Together with the integrated pullup resistor and the external capacitor (Cme), this produces a delay in the measurement after the power transistor has switched on. This delay shall henceforth be known as the response time. This response time (and thus Cme) IGD515EI Vcc Vcc 1k5 1k5 19 Rme ME Dme time - known henceforth as the blocking time. In normal mode (see pin 34 (SDOSA)), the power transistor is also turned off by the intelligent driver's protection function and remains in this state during the blocking time (see Fig. 5). This function is used to protect the component from thermal overload at a continuous or repeated short circuit. The blocking time can be determined by connecting pin 20 (Cb) to pin 24 (COM) via a capacitor (see page 17 for the formula). The capacitance of the blocking capacitor should not exceed a value of 470nF. After the blocking time has elapsed, the power transistor is immediately released again. Cme OVERCURRENT COM 21 REF Dref MEASURING 22 E Fig. 4 Principle of VCE monitoring must be selected to be greater in inverse proportion to the speed at which the power transistors turn on. The formula for dimensioning Cme is given on page 17. Pin 21 - Terminal REF An external zener diode is connected to this pin as a reference. This defines the maximum voltage drop at the turned-on power transistor at which the protective function of the drive circuit is activated. The protection functions of the intelligent drivers of the IGD515EI series always become active when the voltage at ME (measurement drain/collector) is higher than that at REF (see Figs. 4 & 5). It should further be noted that negative voltages are not permissible at the measurement input. The reference potential is the emitter (or source) of the power transistor. The reference must never under any circumstances be capacitively blocked. Pin 20 - Terminal Cb The reference diode should be placed as closely as possible to the driver module. After the current monitoring circuit responds, an error message is reported via the status output SO during a defined IGBT-Driver.com Page 11 IGD515EI Data Sheet & Application Manual Input voltage at Pin 32 (0=Light on; 1=Light off) +5V 0V Gate voltage (Pin 25 to Pin 22) +15V 0V -15V Load current Overcurrent turn-off threshold 0A Status acknowledgement output 0V Blocking time t0 t0 = Power-transistor turn-off in case of overcurrent t0 - t1 = Blocking time (all input signals are ignored) t1 Fig. 5 Principle of the protection function and the blocking time Pin 23 - Terminal Cs A low-inductance blocking capacitor with high ripple (an electrolytic capacitor is usually used) is connected at this output. It decouples the DC/DC converter on the secondary side. The capacitor must supply the pulse currents up to 15A for charging the gate capacitances. The electrolytic capacitor is connected between Cs and COM. Since the charging currents for the gate capacitance are drawn mainly from this electrolytic capacitor, it must definitely be located as closely as possible to the driver module. The terminal assignment is optimally suitable for this purpose. A capacitance up to 250F is recommended. Significantly greater values should not be Page 12 used in order to guarantee problem-free starting of the integrated DC/DC converter. In order to prevent the operating voltage from running up" on the secondary side, a 16V zener diode or a transient voltage suppressor must be connected in parallel to the blocking capacitor. This diode should be designed for a power loss of at least 1.3W. Pin 24 - Terminal COM This is the ground pin of the secondaryside blocking capacitor. It is used at the same time as the reference potential for the measuring filter and the capacitor Cb. INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual The COM terminal can be connected to the source of a power MOSFET in place of E. The anode of the reference diode must then also be connected to this pin. This circuit allows power MOSFETs to be driven without a negative gate voltage. The transistor is then driven in the turned-off state with 0V (unipolar gate driving, see Fig. 6). 19 25 21 24 ME Rme Dme G Cme Rg REF Dref COM Pin 22 (E) is not used Fig. 6 Unipolar gate driving (0/+15V) The terminal E is not used in this circuit and must never under any circumstances be connected to COM. This method of gate driving is not as a rule useful for IGBTs, as a negative gate voltage should always be used for larger modules. Pin 30 - Terminal IGND This is the ground pin for the interface electronics, specifically for the FOL receiver (see Fig. 7). IGBT-Driver.com Pin 31 - Terminal +5V A voltage of +5V with respect to IGND is applied to this pin. It is designed to supply the interface electronics, specifically the FOL receiver (see Fig. 7). The maximum current of 30mA for this output must not be exceeded. Most receivers require less current. If a FOL receiver that requires more than 30mA is used, then an external 5V voltage regulator should be connected. It can be supplied by pin 23 (Cs). Pin 32 - Terminal INPUT The output signal of the FOL receiver is applied to this input (see Fig. 7). In principle, this component may be obtained from any manufacturer. For high-quality applications, however, suitable FOL products should be used. Examples of suitable FOL receivers are: HFBR-2521 and HFBR-2522 (see www.igbt-driver.com/go/fiberoptics). As the familiar FOL receivers supply a 0V signal when the drive information is applied (i.e. when current flows through the FOL receive diode), this input is suitably designed. A 5V signal corresponds to the status of power semiconductor turned off"; a 0V signal to that of power semiconductor turned on". However, the latter output status is possible only when the protection function has not responded in normal mode (see pin 34, SDOSA). The INPUT terminal has a Schmitt trigger characteristic in order to attain a high signal-to-noise ratio. Page 13 IGD515EI Data Sheet & Application Manual Pin 34 - Terminal SDOSA 100nF 31 3 +5V HFBR-2522 RL VCC VO 4 1 INPUT 32 2 GND IGND 30 Fig. 7 Fiber-optic receiver wiring The logic function of the INPUT terminal can also be inverted by pin 33 (INV). Pin 33 - Terminal INV This pin allows the input signal INPUT to be inverted. This input is normally connected to IGND. A 5V signal at the INPUT terminal then corresponds to the status of power transistor turned off" and a 0V signal to that of power transistor turned on". If INV is connected to +5V, then precisely the opposite is true. The input INV allows connection of a FOL receiver with a high" or low" output signal in the driven status. However, this function is used particularly frequently in drives with brake choppers. The status of current in the FOL transmit diode" then means brake chopper turned off". Turn-off or absence of the drive signal then activates the brake. This pin is used for mode selection and affects the reaction of the protection function. In normal operation, the SDOSA terminal (Pin 34) remains open. This has the effect that when a fault (in the desaturation or supply-voltage monitoring circuits) occurs, the power semiconductor is immediately turned off, even if the input signal continues to be applied. The fault status is simultaneously reported to the control electronics via the status output SO. The second operating mode is designed specifically for the series connection of power MOSFETs and IGBTs (e.g. in 3- or multilevel topologies). For this mode, the SDOSA input is connected to +5V. This now has the effect that when an error (in the desaturation or supply-voltage monitoring circuits) occurs, the power semiconductor is not turned off. The status output SO merely reports the error status to the control electronics, which must now centrally turn off all the drivers simultaneously quickly as possible or in a given sequence (3- or multilevel topologies). This is the only way of ensuring the symmetry in the series circuit even if a protective function is triggered. This function can also be used in bridge circuits, for example to ensure that all power semiconductors are turned off simultaneously in the case of a fault. Note that it is recommended to connect pin 33 over a resistor of 100...1k to IGND or +5V. Page 14 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual thus reported to the control electronics (see Fig. 5) Pin 35 - Terminal SO This is the status output of the driver. A FOL transmitter for the status acknowledgement is connected to it via a resistor (see Fig. 8). The supply voltage should be obtained from pin 23 (Cs). A 1 Cs SO 2 IGND 23 +Viso 35 30 Fig. 8 Fiber-optic transmitter wiring voltage of about +15V is present here. The status output SO has the following status: If the supply voltage is too low, then the FET at output SO is through-connected. This means that no current flows through the FOL transmitter. If the supply voltage - but no error status - is applied, then the output SO has highimpedance. This means that a current flows through the FOL transmitter of the status acknowledgement circuit. After the protection function (desaturation monitoring) of the driver has detected an error status, the output SO is through-connected for the duration of the blocking time. The error status is IGBT-Driver.com This output also acknowledges every switching edge of the driving signal with a short pulse, during which the FET becomes conducting (see Fig. 5). The length of the acknowledgement pulse is determined by connecting pin 36 (Cq) to a capacitor. The acknowledgement function allows the control electronics to monitor the operation of both FOL connections (i.e. the drive wire and the status acknowledgement) as well as the driver. If the acknowledgement pulse fails to appear, then the FOL drive connection has probably failed. FOL connections that are incorrectly plugged in and transmit diodes whose luminous power is greatly reduced due to degradation effects often show the following extremely dangerous effect: the receiver emits a highfrequency noise signal in the megahertz range. This leads to thermal destruction of a power semiconductor and possibly also of the driver within short time. An acknowledgement pulse is then present at the SO output with every edge of the input signal. A defective status can be detected by a suitable logic circuit in the control electronics and the system can be turned off. It is further recommended that the status acknowledgements are not connected together in the form of a summed message, but are evaluated as individual signals in a monitoring logic circuit. This significantly simplifies diagnosis and troubleshooting in the event of a fault. Page 15 IGD515EI Data Sheet & Application Manual 1 470 HFBR-1522 3 2 100nF VCC SO ME G 470p 2 32 INPUT 36 Cq 100 33 INV 30 IGND Ref 10 + 250uF GND 1,2,3,4,9 Cb VCC COM GND Dm01 Dm02 Dm03 5,6 25 E IGBT 21 15V Cm Cs +15V Rm 19 68 31 +5V 34 SDOSA HFBR-2522 RL 4 VO 1 GND 3*1N4007 IGD515EI 35 20 15V 5n6 23 Cb + Cs 24 250uF Ds 16V Ref 7V5 330nF 22 Fig. 9 Application example: Driving a 1700V/300A IGBT with IGD515EI Pin 36 - Terminal Cq The length of the acknowledgement pulse at the output SO is determined by a capacitor at this terminal connected to pin 24 (COM). The length of this pulse can then be optimally determined for each application (depending on the throughput rate of the FOL connections and the clock frequency). A capacitor of 470pF at terminal Cq produces an acknowledgement pulse of about 1s. Configuration of the power section The intelligent drivers should be placed as closely as possible to the power transistors. The connection leads to the transistors should be as short as possible, i.e. not more than 3 to 10cm in length depending on the gate current and switching speed. In contrast, the FOL input leads can be of practically any desired length. If no capacitor is connected to terminal Cq, then the acknowledgement pulse is only about 30ns in duration. Unless the FOL connection in the status acknowledgement circuit is extraordinarily fast, an acknowledgement signal is no longer visible at the receiver. This operating mode can be selected when monitoring of the FOL connection is not desired. In principle, however, operation is recommended with the acknowledgement monitoring function. Page 16 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual Application example with a 1700V/300A IGBT Fig. 9 shows an example circuit with a 1700V/300A IGBT. Pin 34 (SDOSA) is open, so the driver is in normal operation. This means that it turns the IGBT off in the event of a fault. Pin 33 (INV) is on ground, so the signal transfer is non-inverting. The capacitor at pin 36 (Cq) generates acknowledgement pulses of about 1s. The response time with Cme=5.6nF and Ref=7V5 is about 7s. This example should give you some initial idea. The exact dimensioning should be checked critically in every application. Formulas for Circuit Calculations Response Time Capacitor Cme = ta 1.5k ln( Vcc ) Vcc - Vref Blocking Time Capacitor At 15V gate driving: Cb = tb 71.6k Cb , max = 470nF At unipolar gate driving (0V/+15V): Cb = tb 100k ln( 2Vcc ) Vref Cb , max = 470nF IGBT-Driver.com Page 17 IGD515EI Data Sheet & Application Manual The Information Source: Driver Data Sheets CONCEPT offers the widest selection of gate drivers for power MOSFETs and IGBTs for almost any application requirements. The largest website on gate-drive circuitry anywhere contains all data sheets, application notes and manuals, technical information and support sections: www.IGBT-Driver.com Quite Special: Customized Drivers If you need an IGBT driver that is not included in the delivery range, please don't hesitate to contact CONCEPT or your CONCEPT sales partner. CONCEPT has more than 20 years experience in the development and manufacture of intelligent gate drivers for power MOSFETs and IGBTs and has already implemented a large number of customized solutions. Technical Support CONCEPT provides expert help with your questions and problems: www.IGBT-Driver.com/go/support Quality The obligation to high quality is one of the central features laid down in the mission statement of CT-Concept Technologie AG. The quality management system covers all stages of product development and production up to delivery. The drivers of the IGD515EI series are manufactured to the ISO9001:2000 quality standard. Legal Disclaimer This data sheet specifies devices but cannot promise to deliver any specific characteristics. No warranty or guarantee is given - either expressly or implicitly - regarding delivery, performance or suitability. CT-Concept Technologie AG reserves the right to make modifications to its technical data and product specifications at any time without prior notice. The general terms and conditions of delivery of CT-Concept Technologie AG apply. Page 18 INTELLIGENT POWER ELECTRONICS IGD515EI Data Sheet & Application Manual Ordering Information The general terms and conditions of delivery of CT-Concept Technologie AG apply. Type Designation Description IGD515EI Single-channel driver core with 15A gate current Product home page: www.IGBT-Driver.com/go/IGD515EI Information about Other Products For other driver cores: Direct link: www.IGBT-Driver.com/go/cores For other drivers, product documentation, evaluation systems and application support Please click onto: www.IGBT-Driver.com Manufacturer CT-Concept Technologie AG Intelligent Power Electronics Renferstrasse 15 CH-2504 Biel-Bienne Switzerland Tel. Fax +41 - 32 - 344 47 47 +41 - 32 - 344 47 40 E-mail Internet Info@IGBT-Driver.com www.IGBT-Driver.com (c) 1992...2010 CT-Concept Technologie AG - Switzerland. We reserve the right to make any technical modifications without prior notice. IGBT-Driver.com All rights reserved. Version of 2010-01-21 Page 19