M36W0Rx0x0x7 32- or 64-Mbit (2 or 4 Mbits x 16, multiple bank, burst) flash memory and 8-Mbit (512 Kbit x16) or 16-Mbit (1 Mbit x 16) PSRAM MCP Features Multichip package - 1 die of 32 or 64 Mbits (2 or 4 Mbits x 16) flash memory - 1 die of 8 Mbits (512 Kbits x 16) or 16 Mbits (1 Mbit x 16) PSRAM FBGA Supply voltage - VDDF = VDDQ = VDDP = 1.7 V to 1.95 V Electronic signature - Manufacturer code: 20h - Device codes (32-Mbit flash device) Top - M36W0R5030T7 and M36W0R5040T7: 8814h Bottom - M36W0R5030B7 and M36W0R5040B7: 8815h - Device codes (8-Mbit flash devices) Top - M36W0R6040T7: 8810h Bottom - M36W0R6040B7: 8811h Stacked TFBGA88 (ZAQ) 8 x 10 mm Block locking - All blocks locked at power-up - Any combination of blocks can be locked - WP for block lock-down Security - 128-bit user programmable OTP cells - 64-bit unique device number Density and Packaging: - RoHS compliant Common flash interface (CFI) Flash memory PSRAM Programming time - 10 s by word typical for fast factory program - Double/quadruple word program option Access time: 60 ns Memory blocks - Multiple bank memory array: 4-Mbit banks - Parameter blocks (top or bottom location) Table 1. 100,000 program/erase cycles per block Synchronous/asynchronous read - Synchronous burst read mode: 66 MHz - Asynchronous page read mode - Random access times: 70 ns Low standby current: 70 A Deep power-down current: 10 A Device summary M36W0Rx0x0x7 M36W0R5030T7 M36W0R5030B7 M36W0R5040T7 M36W0R5040B7 M36W0R6040T7 M36W0R6040B7 Synchronous burst read suspend Dual operations - Program erase in 1 bank, read in others - No delay between read and write operations April 2009 209220 - Rev 3 1/24 www.numonyx.com 1 Contents M36W0Rx0x0x7 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.1 Address inputs (A0-A21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.2 Data input/output (DQ0-DQ15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.3 Flash Chip Enable (EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.4 Flash Output Enable (GF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.5 Flash Write Enable (WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.6 Flash Write Protect (WPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.7 Flash Reset (RPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.8 Flash Latch Enable (LF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.9 Flash Clock (KF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.10 Flash Wait (WAITF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.11 PSRAM Chip Enable (EP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.12 PSRAM Output Enable (GP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.13 PSRAM Write Enable (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.14 PSRAM Upper Byte Enable (UBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.15 PSRAM Lower Byte Enable (LBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.16 VDDF supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.17 VDDP supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.18 VDDQ supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2.19 VPPF program supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.20 VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 5 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6 Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 7 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 2/24 M36W0Rx0x0x7 8 Contents Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 3/24 List of tables M36W0Rx0x0x7 List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. 4/24 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Main operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Device capacitance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Stacked TFBGA88 8 x 10 mm - 8 x 10 ball array, 0.8 mm pitch, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 M36W0Rx0x0x7 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 TFBGA connections (top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Stacked TFBGA88 8 x 10 mm - 8 x 10 active ball array, 0.8 mm pitch, package outline . . 20 5/24 Description 1 M36W0Rx0x0x7 Description The M36W0R5030x7, M36W0R5040x7, and M36W0R6040x7 combine two memory devices in a multichip package: a 32- or 64-Mbit, multiple bank flash memory, the M58WR032KT/B or M58WR064KT/B, respectively. a 8- or 16-Mbit PSRAM, the M69KB012AB or M69KB024AB, respectively. Recommended operating conditions do not allow more than one memory to be active at the same time. The purpose of this document is to describe how the two memory components operate with respect to each other. It must be read in conjunction with the datasheets of the M58WR032KT/B or M58WR064KT/B, and M69KB012AB or M69KB024AB, respectively, which fully detail all the specifications required to operate the flash memory and PSRAM components. The memory is offered in a stacked TFBGA88 (8 x 10 mm, 8 x 10 ball array, 0.8 mm pitch) package, and is supplied with all the bits erased (set to `1'). 6/24 M36W0Rx0x0x7 Figure 1. Description Logic diagram VDDQ VPPF VDDP VDDF 22 16 A0-Amax(1) DQ0-DQ15 EF GF WAIT WF RPF WPF L M36W0R5030x7 M36W0R5040x7 M36W0R6040x7 K EP GP WP UBP LBP VSS Ai11080f 1. Amax is equal to A20 in the M36W0R50x0x7 and A21 in the M36W0R6040x7. 7/24 Description M36W0Rx0x0x7 Table 2. Signal names(1) Name Function A0-A18 Common address inputs DQ0-DQ15 Common data input/output VDDF Flash Memory power supply VDDQ Common flash and PSRAM power supply for I/O buffers VPPF Common flash optional supply voltage for fast program and erase VSS Ground VCCP PSRAM power supply NC Not connected internally DU Do not use as internally connected Flash memory control functions A19-A20, A20, or A20-A21(2) Address inputs for the flash memory only EF Chip Enable input GF Output Enable input LF Latch Enable input KF Burst Clock WAITF Wait data in burst mode WF Write Enable input RPF Reset input WPF Write Protect input PSRAM control functions EP Chip Enable input GP Output Enable input WP Write Enable input UBP Upper Byte Enable input LBP Lower Byte Enable input 1. A0-A18 (in the case of an 8-Mbit PSRAM) or A0-A19 (in the case of a 16-Mbit PSRAM) are common to the flash memory and the PSRAM. 2. A19-A20 for the M36W0R5030x7, A20 for the M36W0R5040x7, and A20-A21 for the M36W0R6040x7. 8/24 M36W0Rx0x0x7 Description Figure 2. TFBGA connections (top view through package) 1 2 3 4 5 A DU DU B A4 A18 A19 VSS VDDF C A5 LBP NC VSS D A3 A17 NC E A2 A7 F A1 G 6 7 8 DU DU NC A21 A11 NC KF NC A12 VPPF WP EP A9 A13 NC WPF LF A20 A10 A15 A6 UBP RPF WF A8 A14 A16 A0 DQ8 DQ2 DQ10 DQ5 DQ13 WAITF NC H GP DQ0 DQ1 DQ3 DQ12 DQ14 DQ7 NC J NC GF DQ9 DQ11 DQ4 DQ6 DQ15 VDDQ K EF NC NC NC VCCP NC VDDQ NC L VSS VSS VDDQ VDDF VSS VSS VSS VSS M DU DU DU DU AI08525d 9/24 Signal descriptions 2 M36W0Rx0x0x7 Signal descriptions See Figure 1: Logic diagram and Table 2: Signal names for a brief overview of the signals connected to this device. 2.1 Address inputs (A0-A21) Addresses A0-A18 are common inputs for the flash memory and PSRAM components. The address inputs select the cells in the memory array to access during bus read operations. During bus write operations they control the commands sent to the command interface of the flash memory program/erase controller, and they select the cells to access in the PSRAM. Addresses A19-A20 (for the M36W0R5030x7), A20 (for the M36W0R5040x7), and A20-A21 (for the M36W0R6040x7) are inputs for the flash memory component only. The flash memory is accessed through the Chip Enable signals (EF) and through the Write Enable (WF) signal. 2.2 Data input/output (DQ0-DQ15) For the flash memory, the data I/O outputs the data stored at the selected address during a bus read operation or inputs a command or the data to be programmed during a write bus operation. For the PSRAM, the upper byte data inputs/outputs carry the data to or from the upper part of the selected address during a write or read operation, when upper byte enable (UBP) is driven Low. Likewise, the lower byte data inputs/outputs carry the data to or from the lower part of the selected address during a write or read operation, when Lower Byte Enable (LBP) is driven Low. 2.3 Flash Chip Enable (EF) The Chip Enable inputs activate the memory control logics, input buffers, decoders and sense amplifiers. When Chip Enable is Low, VIL, and Reset is High, VIH, the device is in active mode. When Chip Enable is at VIH the flash memory is deselected, the outputs are high impedance and the power consumption is reduced to the standby level. 2.4 Flash Output Enable (GF) The Output Enable pins control data outputs during flash memory bus read operations. 2.5 Flash Write Enable (WF) The Write Enable controls the bus write operation of the flash memories' command interface. The data and address inputs are latched on the rising edge of Chip Enable or Write Enable, whichever occurs first. 10/24 M36W0Rx0x0x7 2.6 Signal descriptions Flash Write Protect (WPF) Write Protect is an input that gives an additional hardware protection for each block. When Write Protect is Low, VIL, lock-down is enabled and the protection status of the locked-down blocks cannot be changed. When Write Protect is at High, VIH, lock-down is disabled and the locked-down blocks can be locked or unlocked (refer to the lock status table in M58WR032KT/B and M58WR064KT/B datasheet). 2.7 Flash Reset (RPF) The Reset input provides a hardware reset of the memory. When Reset is at VIL, the memory is in reset mode: the outputs are high impedance and the current consumption is reduced to the Reset supply current IDD2. Refer to the M58WR032KT/B or M58WR064KT/B datasheet for the value of IDD2. After Reset all blocks are in the locked state and the configuration register is reset. When Reset is at VIH, the device is in normal operation. Upon exiting reset mode the device enters asynchronous read mode, but a negative transition of Chip Enable or Latch Enable is required to ensure valid data outputs. The Reset pin can be interfaced with 3 V logic without any additional circuitry. It can be tied to VRPH (refer to the M58WR032KT/B or M58WR064KT/B datasheet). 2.8 Flash Latch Enable (LF) Latch Enable latches the address bits on its rising edge. The address latch is transparent when Latch Enable is Low, VIL, and it is inhibited when Latch Enable is High, VIH. Latch Enable can be kept Low (also at board level) when the Latch Enable function is not required or supported. 2.9 Flash Clock (KF) The Clock input synchronizes the flash memory to the microcontroller during synchronous read operations; the address is latched on a Clock edge (rising or falling, according to the configuration settings) when Latch Enable is at VIL. Clock is `don't care' during asynchronous read and in write operations. 2.10 Flash Wait (WAITF) WAIT is a flash output signal used during synchronous read to indicate whether the data on the output bus are valid. This output is high impedance when flash Chip Enable is at VIH or flash Reset is at VIL. It can be configured to be active during the wait cycle or one clock cycle in advance. The WAITF signal is not gated by Output Enable. 2.11 PSRAM Chip Enable (EP) When asserted (Low), the Chip Enable, EP, activates the memory state machine, address buffers and decoders, allowing read and write operations to be performed. When deasserted (High), all other pins are ignored and the device is automatically put in low-power standby mode. 11/24 Signal descriptions 2.12 M36W0Rx0x0x7 PSRAM Output Enable (GP) The Output Enable, GP, provides a high speed tri-state control, allowing fast read/write cycles to be achieved with the common I/O data bus. 2.13 PSRAM Write Enable (WP) The Write Enable, WP, controls the bus write operation of the memory. 2.14 PSRAM Upper Byte Enable (UBP) The Upper Byte Enable, UBP, gates the data on the upper byte data inputs/outputs (DQ8DQ15) to or from the upper part of the selected address during a write or read operation. 2.15 PSRAM Lower Byte Enable (LBP) The Lower Byte Enable, LBP, gates the data on the lower byte data inputs/outputs (DQ0DQ7) to or from the lower part of the selected address during a write or read operation. 2.16 VDDF supply voltage VDDF provides the power supply to the internal core of the flash memory component. It is the main power supplies for all flash memory operations (read, program, and erase). 2.17 VDDP supply voltage The VDDP supply voltage supplies the power for all operations (read or write) and for driving the refresh logic, even when the device is not being accessed. 2.18 VDDQ supply voltage VDDQ provides the power supply for the flash memory and PSRAM I/O pins. This allows all outputs to be powered independently of the flash memory and PSRAM core power supplies: VDDF and VDDP, respectively. 12/24 M36W0Rx0x0x7 2.19 Signal descriptions VPPF program supply voltage VPPF is both a flash memory control input and a flash memory power supply pin. The two functions are selected by the voltage range applied to the pin. If VPPF is kept in a low voltage range (0 V to VDDQ) VPPF is seen as a control input. In this case a voltage lower than VPPLKF provides absolute protection against program or erase, while VPPF > VPP1F enables these functions (see the M58WR032KT/B and M58WR064KT/B datasheet for the relevant values). VPPF is only sampled at the beginning of a program or erase; a change in its value after the operation has started does not have any effect and program or erase operations continue. If VPPF is in the range of VPPHF it acts as a power supply pin. In this condition VPPF must be stable until the program/erase algorithm is completed. 2.20 VSS ground VSS is the common ground reference for all voltage measurements in the flash (core and I/O buffers) and PSRAM chips. Note: Each flash memory device in a system should have its supply voltage (VDDF) and the program supply voltage VPPF decoupled with a 0.1 F ceramic capacitor close to the pin (high-frequency, inherently-low inductance capacitors should be as close as possible to the package). See Figure 5: AC measurement load circuit. The PCB track widths should be sufficient to carry the required VPPF program and erase currents. 13/24 Functional description 3 M36W0Rx0x0x7 Functional description The flash memory and PSRAM components have separate power supplies but share the same grounds. They are distinguished by two Chip Enable inputs: EF for the flash memory and EP for the PSRAM. Recommended operating conditions do not allow more than one device to be active at a time. The most common example is simultaneous read operations on the flash memory and the PSRAM which would result in a data bus contention. Therefore, it is recommended to put the other devices in the high impedance state when reading the selected device. 14/24 M36W0Rx0x0x7 Functional description Figure 3. Functional block diagram VDDF VPPF VDDQ A19-20(1) or A20(2) or A20-A21(3) EF GF 32 or 64-Mbit flash memory WF WAITF LF KF RPF A0-A18(1) or A0-A19(2)(3) WPF DQ0-DQ15 VDDP EP GP 8 or 16-Mbit PSRAM WP UBP LBP VSS AI08449e 1. Address inputs corresponding to the M36W0R5030x7 devices. 2. Address inputs corresponding to the M36W0R5040x7 devices. 3. Address inputs corresponding to the M36W0R6040x7 devices. 15/24 Functional description Table 3. M36W0Rx0x0x7 Main operating modes(1) Operation Flash read WAIT(2) EF GF WF L RPF VIL VIL VIH VIL(3) VIH Flash data out VIH Flash data in Flash write VIL VIH VIL VIL(3) Flash address latch VIL X VIH VIL VIH Flash output disable VIL VIH VIH X VIH Flash standby VIH X X X VIH Hi-Z X X X X VIL Hi-Z Flash reset PSRAM read PSRAM write GP WP UBP LBP PSRAM must be disabled DQ15-DQ0 Flash data out or HiZ(4) Flash Hi-Z Flash memory must be disabled PSRAM standby PSRAM deep power-down EP Any flash mode is allowed. Flash Hi-Z Any PSRAM mode is allowed Flash Hi-Z VIL VIL VIH VIL VIL PSRAM data out VIL X VIL VIL VIL PSRAM data in VIH X X X X PSRAM Hi-Z VIH X X X X PSRAM Hi-Z 1. X = `don't care'. 2. WAIT signal polarity is configured using the Set Configuration Register command. Refer to M58WR032KT/B and M58WR064KT/B datasheet for details. 3. L can be tied to VIH if the valid address has been previously latched. 4. Depends on GF. 16/24 M36W0Rx0x0x7 4 Maximum ratings Maximum ratings Stressing the device above the rating listed in Table 4: Absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 4. Absolute maximum ratings Value Symbol Parameter Unit Min Max Ambient operating temperature -40 85 C TBIAS Temperature under bias -40 125 C TSTG Storage temperature -55 125 C Input or output voltage -0.5 3.3 V VDDF Flash memory core supply voltage -0.2 2.45 V VDDQ Input/output supply voltage -0.2 2.45 V VDDP PSRAM supply voltage -0.5 3.3 V VPPF Flash memory program voltage -0.2 10 V Output short circuit current 100 mA Time for VPPF at VPPFH 100 hours TA VIO IO tVPPFH 17/24 DC and AC parameters 5 M36W0Rx0x0x7 DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics tables in this section are derived from tests performed under the measurement conditions summarized in Table 5. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 5. Operating and AC measurement conditions Flash memory PSRAM Parameter Unit Min Max Min Max VDDF supply voltage 1.7 1.95 - - V VDDP supply voltage - - 1.7 1.95 V VDDQ supply voltage 1.7 1.95 - - V VPPF supply voltage (factory environment) 8.5 9.5 - - V VPPF supply voltage (application environment) -0.4 VDDQ +0.4 - - V Ambient operating temperature -40 85 -40 85 C Load capacitance (CL) 30 Input rise and fall times 5 Input pulse voltages Input and output timing ref. voltages Figure 4. 50 2 ns 0 to VDDQ 0 to VDDP V VDDQ/2 VDDP/2 V AC measurement I/O waveform VDDQ VDDQ/2 0V AI06161 18/24 pF M36W0Rx0x0x7 DC and AC parameters Figure 5. AC measurement load circuit VDDQ VDDF VDDQ 22k DEVICE UNDER TEST CL 0.1F 22k 0.1F CL includes JIG capacitance AI10061 Table 6. Symbol CIN COUT Device capacitance(1) Parameter Input capacitance Output capacitance Test condition Min Max Unit VIN = 0 V 12 pF VOUT = 0 V 15 pF 1. Sampled only, not 100% tested. Please refer to the M58WR032KT/B and M58WR064KT/B and M69KB012AB or M69KB024AB datasheets for further DC and AC characteristics values and illustrations. 19/24 Package mechanical 6 M36W0Rx0x0x7 Package mechanical To meet environmental requirements, Numonyx offers the M36W0R50x0x7 and M36W0R6040x7 in RoHS compliant packages, which have a lead-free second-level interconnect. In compliance with JEDEC standard JESD97, the category of second-level interconnect is marked on the package and on the inner box label. The maximum ratings related to soldering conditions are also marked on the inner box label. Note: RoHS compliant specifications are available at www.numonyx.com. Figure 6. Stacked TFBGA88 8 x 10 mm - 8 x 10 active ball array, 0.8 mm pitch, package outline D D1 e SE E E2 E1 b BALL "A1" ddd FE FE1 FD SD A2 A A1 BGA-Z42 1. Drawing is not to scale. 20/24 M36W0Rx0x0x7 Package mechanical Table 7. Stacked TFBGA88 8 x 10 mm - 8 x 10 ball array, 0.8 mm pitch, package mechanical data Millimeters Inches Symbol Typ Min A Max Typ Min 1.200 A1 Max 0.0472 0.200 0.0079 A2 0.850 0.0335 b 0.350 0.300 0.400 0.0138 0.0118 0.0157 D 8.000 7.900 8.100 0.3150 0.3110 0.3189 D1 5.600 0.2205 ddd 0.100 9.900 E 10.000 E1 7.200 0.2835 E2 8.800 0.3465 e 0.800 FD 1.200 0.0472 FE 1.400 0.0551 FE1 0.600 0.0236 SD 0.400 0.0157 SE 0.400 0.0157 - 10.100 0.0039 - 0.3937 0.0315 0.3898 0.3976 - - 21/24 Part numbering 7 M36W0Rx0x0x7 Part numbering Table 8. Ordering information scheme Example: M36 W 0 R 6 0 4 0 T 7 ZAQ E Device type M36 = multichip package (multiple flash + RAM) Flash 1 architecture W = multiple bank, burst mode Flash 2 architecture 0 = none present Operating voltage R = VDDF = VDDQ =VCCP = 1.7 V to 1.95 V Flash 1 density 5 = 32-Mbit 6 = 64-Mbit Flash 2 density 0 = none present RAM 1 density 3 = 8-Mbit 4 = 16-Mbit RAM 0 density 0 = none present Parameter blocks location T = top boot block flash B = bottom boot block flash Product version 7 = 65 nm flash technology, 70 ns; 0.125?m RAM Package ZAQ = stacked TFBGA88 8 x 10 mm - 8 x 10 active ball array, 0.8 mm pitch Option E = RoHS compliant package, standard packing F = RoHS compliant package, tape and reel packing Devices are shipped from the factory with the memory content bits erased to '1'. For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact the Numonyx sales office nearest to you. 22/24 M36W0Rx0x0x7 8 Revision history Revision history Table 9. Document revision history Date Version Revision Details 30-Jun-2008 1 Initial release. 29-Sep-2008 2 Change from T=-30C to T=-40C. 31-Mar-2009 3 Replaced references to ECOPACK with RoHS compliant. Changed footnote 1 in figure1. 23/24 M36W0Rx0x0x7 Please Read Carefully: INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYXTM PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting Numonyx's website at http://www.numonyx.com. Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 11/5/7, Numonyx, B.V., All Rights Reserved. 24/24