Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series 1.5SMC Series RoHS Description Uni-directional Bi-directional The 1.5SMC series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25C unless otherwise noted) Parameter Symbol Value Unit Peak Pulse Power Dissipation at TA=25C by 10/1000s Waveform (Fig.2)(Note 1), (Note 2) PPPM 1500 W Power Dissipation on Infinite Heat Sink at TA=50C PM(AV) 6.5 W IFSM 200 A Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) * For surface mounted applications to optimize board space * Low profile package. * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) *E SD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) *E FT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Built-in strain relief * VBR @TJ= VBR@25C x (1+T x (TJ - 25)) (T: Temperature Coefficient) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 4) * 1500W peak pulse power capability at 10/1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0V to BV min * Excellent clamping capability * Low incremental surge resistance * Typical IR less than 1A above 13V * High temperature soldering guaranteed: 260C/40 seconds at terminals * Plastic package has underwriters laboratory flammability 94V-O * Meet MSL level1, per J-STD-020, LF maximum peak of 260C * Matte tin lead-free plated * Halogen free and RoHS compliant VF 3.5/5.0 V TJ , TSTG -55 to 150 C Typical Thermal Resistance Junction to Lead RuJL 15 C/W Applications Typical Thermal Resistance Junction to Ambient RuJA 75 C/W TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25C per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31" (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. 4. VF<3.5V for VBR < _ 200V and VF<5.0V for VBR > _ 201V. * Glass passivated chip junction Additional Information Functional Diagram Datasheet Bi-directional Cathode Anode Uni-directional (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13 Resources Samples Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series Electrical Characteristics.(TA=25C unless otherwise noted) Part Number (Uni) Part Number (Bi) 1.5SMC6.8A 1.5SMC7.5A 1.5SMC8.2A 1.5SMC9.1A 1.5SMC10A 1.5SMC11A 1.5SMC12A 1.5SMC13A 1.5SMC15A 1.5SMC16A 1.5SMC18A 1.5SMC20A 1.5SMC22A 1.5SMC24A 1.5SMC27A 1.5SMC30A 1.5SMC33A 1.5SMC36A 1.5SMC39A 1.5SMC43A 1.5SMC47A 1.5SMC51A 1.5SMC56A 1.5SMC62A 1.5SMC68A 1.5SMC75A 1.5SMC82A 1.5SMC91A 1.5SMC100A 1.5SMC110A 1.5SMC120A 1.5SMC130A 1.5SMC150A 1.5SMC160A 1.5SMC170A 1.5SMC180A 1.5SMC200A 1.5SMC220A 1.5SMC250A 1.5SMC300A 1.5SMC350A 1.5SMC400A 1.5SMC440A 1.5SMC480A 1.5SMC510A 1.5SMC530A 1.5SMC540A 1.5SMC550A 1.5SMC6.8CA 1.5SMC7.5CA 1.5SMC8.2CA 1.5SMC9.1CA 1.5SMC10CA 1.5SMC11CA 1.5SMC12CA 1.5SMC13CA 1.5SMC15CA 1.5SMC16CA 1.5SMC18CA 1.5SMC20CA 1.5SMC22CA 1.5SMC24CA 1.5SMC27CA 1.5SMC30CA 1.5SMC33CA 1.5SMC36CA 1.5SMC39CA 1.5SMC43CA 1.5SMC47CA 1.5SMC51CA 1.5SMC56CA 1.5SMC62CA 1.5SMC68CA 1.5SMC75CA 1.5SMC82CA 1.5SMC91CA 1.5SMC100CA 1.5SMC110CA 1.5SMC120CA 1.5SMC130CA 1.5SMC150CA 1.5SMC160CA 1.5SMC170CA 1.5SMC180CA 1.5SMC200CA 1.5SMC220CA 1.5SMC250CA 1.5SMC300CA 1.5SMC350CA 1.5SMC400CA 1.5SMC440CA 1.5SMC480CA 1.5SMC510CA 1.5SMC530CA 1.5SMC540CA 1.5SMC550CA UNI BI Reverse Stand off Voltage VR (Volts) 6V8A 7V5A 8V2A 9V1A 10A 11A 12A 13A 15A 16A 18A 20A 22A 24A 27A 30A 33A 36A 39A 43A 47A 51A 56A 62A 68A 75A 82A 91A 68A 75A 120A 130A 150A 160A 170A 180A 200A 220A 250A 300A 350A 400A 440A 480A 510A 530A 540A 550A 6V8C 7V5C 8V2C 9V1C 10C 11C 12C 13C 15C 16C 18C 20C 22C 24C 27C 30C 33C 36C 39C 43C 47C 51C 56C 62C 68C 75C 82C 91C 100C 110C 120C 130C 150C 160C 170C 180C 200C 220C 250C 300C 350C 400C 440C 480C 510C 530C 540C 550C 5.80 6.40 7.02 7.78 8.55 9.40 10.20 11.10 12.80 13.60 15.30 17.10 18.80 20.50 23.10 25.60 28.20 30.80 33.30 36.80 40.20 43.60 47.80 53.00 58.10 64.10 70.10 77.80 85.50 94.00 102.00 111.00 128.00 136.00 145.00 154.00 171.00 185.00 214.00 256.00 300.00 342.00 376.00 408.00 434.00 477.00 486.00 495.00 Marking Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.45 7.13 7.79 8.65 9.50 10.50 11.40 12.40 14.30 15.20 17.10 19.00 20.90 22.80 25.70 28.50 31.40 34.20 37.10 40.90 44.70 48.50 53.20 58.90 64.60 71.30 77.90 86.50 95.00 105.00 114.00 124.00 143.00 152.00 162.00 171.00 190.00 209.00 237.00 285.00 332.00 380.00 418.00 456.00 485.00 503.50 513.00 522.50 7.14 7.88 8.61 9.50 10.50 11.60 12.60 13.70 15.80 16.80 18.90 21.00 23.10 25.20 28.40 31.50 34.70 37.80 41.00 45.20 49.40 53.60 58.80 65.10 71.40 78.80 86.10 95.50 105.00 116.00 126.00 137.00 158.00 168.00 179.00 189.00 210.00 231.00 263.00 315.00 368.00 420.00 462.00 504.00 535.00 556.50 567.00 577.50 10 10 10 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Maximum Maximum Maximum Agency Clamping Peak Reverse Approval Voltage VC Pulse Leakage IR @ Ipp Current Ipp @ VR (V) (A) (A) 10.5 11.3 12.1 13.4 14.5 15.6 16.7 18.2 21.2 22.5 25.2 27.7 30.6 33.2 37.5 41.4 45.7 49.9 53.9 59.3 64.8 70.1 77.0 85.0 92.0 103.0 113.0 125.0 137.0 152.0 165.0 179.0 207.0 219.0 234.0 246.0 274.0 328.0 344.0 414.0 482.0 548.0 602.0 658.0 698.0 725.0 740.0 760.0 144.8 134.5 125.6 113.4 104.8 97.4 91.0 83.5 71.7 67.6 60.3 54.9 49.7 45.8 40.5 36.7 33.3 30.5 28.2 25.6 23.5 21.7 19.7 17.9 16.5 14.8 13.5 12.2 11.1 10.0 9.2 8.5 7.3 6.9 6.5 6.2 5.5 4.6 4.4 3.7 3.2 2.8 2.5 2.3 2.1 2.1 2.0 2.0 1000 500 200 50 10 5 5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is 10% and Vc is 5% higher than with A parts. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT Vc VBR VR V IT IR IR IT VR VBR Vc V Ipp Ipp PPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) IR Reverse Leakage Current -- Current measured at VR VF Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (TA=25C unless otherwise noted) Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating 100 PPPM-Peak Pulse Power (kW) Voltage Transients Voltage or Current Voltage Across TVS Current Through TVS 10 0.31x0.31" (8.0x8.0mm) Copper Pad Area 1 0.000001 Time 0.00001 0.0001 0.001 td-Pulse Width (sec.) continues on next page. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series Ratings and Characteristic Curves (TA=25C unless otherwise noted) (Continued) Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage % 100 75 50 25 tr=10sec 25 50 75 100 125 150 175 Peak Value IPPM 100 Half Value IPPM IPPM ( ) 2 50 0 0 0 200 10/1000sec. Waveform as defined by R.E.A td 1.0 0 TA - Ambient Temperature (C) Cj (pF) PM(AV), Steady Sate Power Dissipation (W) Bi-directional V=0V Uni-directional V=0V Uni-directional @VR 100 Bi-directional @VR 10 Tj=25C f=1.0MHz Vsig=50mVp-p 1 1.0 3.0 4.0 Figure 6 - Steady State Power Dissipation Derating Curve 100000 1000 2.0 t-Time (ms) Figure 5 - Typical Junction Capacitance 10000 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 10.0 100.0 1000.0 VBR - Reverse Breakdown Voltage (V) 6.5 6 5.5 5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0 25 50 75 100 125 150 175 TA - Ambient Temperature (C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only IFSM - Peak Forward Surge Current (A) 200 180 160 140 120 100 80 60 40 20 0 1 10 100 Number of Cycles at 60 Hz (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13 Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series Soldering Parameters Lead-free assembly Pre Heat - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max TS(max) to TL - Ramp-up Rate 3C/second max Reflow - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Ramp-down Rate 6C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C Physical Specifications tp TP Ramp-up TL Temperature (T) Reflow Condition tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 25C t 25C to Peak Time (t) Environmental Specifications High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Weight 0.007 ounce, 0.21 grams Case JEDEC DO214AB. Molded plastic body over glass passivated junction MSL JEDEC-J-STD-020C, Level 1 Polarity Color band denotes positive end (cathode) except Bidirectional. H3TRB JESD22-A101 Terminal Matte Tin-plated leads, Solderable per JESD22-B102D RSH JESD22-B106C Dimensions DO-214AB (SMC J-Bend) Dimensions Cathode Band (for uni-directional products only) A C A B H D F E G J K L Dimensions in inches and (millimeters) I Solder Pads (all dimensions in mm) (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13 Inches Millimeters Min Max Min Max 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - Transient Voltage Suppression Diodes Surface Mount - 1500W > 1.5SMC series Part Numbering System Part Marking System 1.5SMC XXX C A F Cathode Band XXX 5% VBR VOLTAGE TOLERANCE YMXXX BI-DIRECTIONAL (for uni-directional products only) Littelfuse Logo Marking Code Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code VBR VOLTAGE SERIES Packaging Part number Component Package 1.5SMCxxxXX DO-214AB Quantity 3000 Packaging Option Tape & Reel - 16mm/13" tape Packaging Specification EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 (8.0) 0.059 DIA (1.5) Cover tape 13.0 (330) 0.80 (20.2) Arbor Hole Dia. 0.65 (16.4) Dimensions are in inches (and millimeters). Direction of Feed (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 09/13/13