1.9mm Round Subminiature" Z-Bend" Lead Infrared LED IR95-21C/TR9 Features Small double-end package High reliability Low forward voltage Good spectral matching to Si photodetector .Pb free The product itself will remain within RoHS compliant version. Compliance with EU REACH. Compliance Halogen Free .(Br <900 ppm ,Cl <900 ppm , Br+Cl < 1500 ppm) Description IR95-21C/L491/TR10 is an infrared emitting diode in miniature SMD package which is molded in a water clear plastic with spherical top view lens. The device is spectrally matched with silicon photodiode and phototransistor. Applications PCB mounted infrared sensor Infrared emitting for miniature light barrier Floppy disk drive Optoelectronic switch Smoke detector Device Selection Guide 1 Device No. Chip Material Lens Color IR GaAlAs Water Clear Copyright (c) 2015, Everlight All Rights Reserved. Release Date: 2016/11/28. Issue No: DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Package Dimensions 2.1 0.1 0.4 0.1 0.5 0.1 2.2 0.1 1.9 0.2 4.7 0.1 2.7 0.1 1.4 0.1 R0.4 0.1 1.3 0.1 0.65 0.1 0.15 0.05 R0.8 0.1 0.75 0.1 7.4 0.2 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.1mm 2 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Units Continuous Forward Current IF 65 mA Reverse Voltage PowerDissipation at(or below) 25Free Air Temperature VR 5 V Pd 130 mW Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +100 Tsol 260 Soldering Temperature *1 Notes: *1: Soldering time5 seconds. Electro-Optical Characteristics (Ta=25) Parameter Symbol Radiant Intensity Ie Peak Wavelength p Spectral Bandwidth Conditions Min. Typ. Max. Units 3.0 5.0 -- mW/sr -- 940 -- nm -- 45 -- nm Forward Voltage VF -- 1.2 1.5 V Reverse Current IR VR=5V -- -- 10 A View Angle 21/2 IF=20mA -- 25 -- deg IF=20mA Intensity Specifications for Bin Grading Rank J K L M N P Q R S T 3 Test Condition IF=20mA Min 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 Max 4.5 6.0 7.5 9.0 10.5 12.0 13.5 15.0 16.5 18.0 Unit mW/sr Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Typical Electro-Optical Characteristics Curves Fig.1 Forward Current vs. Ambient Temperature Fig.2 Spectral Distribution * Fig.3 Forward Current vs. Forward Voltage 10 Fig.4 Peak Emission Wavelength Ambient Temperature 980 4 960 10 3 940 10 2 920 1 10 0 4 1 2 3 4 900 -25 0 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 25 Rev.3 50 75 100 www.everlight.com DATASHEET IR95-21C/TR9 Typical Electro-Optical Characteristics Curves Fig.4 Relative Radiant Intensity vs Angular Displacement -20 -10 0 10 20 30 1.0 40 0.9 50 0.8 0.7 60 70 80 0.6 0.4 0.2 5 0 0.2 0.4 0.6 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 10~30 and 90%RH or less. 2.3 The LEDs suggested be used within one year. 2.4 After opening the package, the devices must be stored at 10C~30C and 60%RH, and used within 168 hours (floor life). If unused LEDs remain, it should be stored in moisture proof packages. 2.5 If the moisture absorbent material (desiccant material) has faded or unopened bag has exceeded the shelf life or devices (out of bag) have exceeded the floor life, baking treatment is required. 2.6 If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure or recommend the following conditions: 96 hours at 60C 5C and < 5 % RH (reeled/tubed/loose units) 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than three times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 6 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 4. Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5. Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. 7 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Package Dimensions Note: The tolerances unless mentioned are 0.1 mm, Unit: mm. Carrier Tape Dimensions: (Quantity: 1000pcs/reel) + Note: The tolerances unless mentioned are 0.1 mm, Unit: mm. 8 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com DATASHEET IR95-21C/TR9 Packing Quantity Specification 1.1000Pcs/1Volume1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number DISCLAIMER 1. EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification. 2. The product meets EVERLIGHT published specification for a period of twelve (12) months from date of shipment. 3. The graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is prohibited without obtaining EVERLIGHT's prior consent. 6. This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. Please contact authorized Everlight sales agent for special application request. 9 Copyright (c) 2015, Everlight All Rights Reserved. Release Date :2016/11/28. Issue No:DIR-0001677 Rev.3 www.everlight.com