Click on Series name for product info on aimtec.com Series AMSR2-78-NZ Up to 13 Watt | DC-DC Switching Regulator FEATURES: * * * * 3 Pin SIP Package Pin-out compatible withLM78XX Linear Regulators Continuous Short Circuit Protection Non-Isolated Regulated Outputs * * * * Operating temperature -40C to +85C Wide input range Very High Efficiency Up To 92% Low ripple and noise Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) Efficiency Vin Min (%) Efficiency Vin Max (%) AMSR2-783.3-NZ 4.75-18 3.3 2 87 86 AMSR2-7805-NZ 7-18 5 2 91 88 AMSR2-786.5-NZ 8.5-18 6.5 2 92 91 AMSR2-783.3L-NZ 4.75-18 3.3 2 87 86 AMSR2-7805L-NZ 7-18 5 2 91 88 AMSR2-786.5L-NZ 8.5-18 6.5 2 92 91 NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Input Specifications Voltage range Filter Quiescent Current Nominal Typical Vin=(LL-HL) at full load Maximum See the table above Capacitor 5 Units VDC 10 mA Maximum Units Output Specifications Output Specifications Voltage accuracy Short Circuit protection Short circuit restart Output current limit Thermal shutdown Dynamic load stability Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Maximum Capacitive Load Conditions Typical 100% load 3 Continuous. Auto recovery % 5 Internal IC junction 10-100% load Vin=(LL-HL) at full load 10-100% load -40C to +85C ambient 20MHz Bandwidth 1000 A C mV % % %/oC mV p-p F Maximum Units 100 KHz oC oC oC 150 100 0.75 1 0.03 45 General Specifications Input Specifications Switching frequency Operating temperature Storage temperature Max Case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Soldering Temperature Conditions Typical 100% load With derating above 71C 340 -40 to +85 -55 to +125 Free air convection 95 Non-conductive black plastic (UL94-V0 rated) 4 0.45 X 0.35 X 0.69 inch 11.50 X 8.90 X 17.50 mm > 2 000 000 hrs (MIL-HDBK-217F, Ground Benign, t=+25C) 1.5 mm from case for 10 sec 300 % g oC Safety Specifications www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 1 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR2-78-NZ Up to 13 Watt | DC-DC Switching Regulator Parameters Approvals Standards CE, UL EN/IEC/UL60950-1 Pin Out Specifications Pin Single 1 2 3 +Vin GND +Vout Footprint 2.54 (0.10) Dimensions O 1.0 +0.15/-0 (O 0.04 + 0.006/-0 2.54 (0.10) DIV: 2.54 (0.1) Dimensions are typical values: mm (inch) General Tolerance: 0.25 ( 0.01) Pin Tolerance: 0.1 ( 0.004) www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 2 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR2-78-NZ Up to 13 Watt | DC-DC Switching Regulator L Models Footprint 11.5 (0.45) 17.5 (0.69) 1.4 (0.05) 9.0 (0.35) Bottom View 4.1 (0.16) 5.1 (0.2) 19.0 (0.75) 0.5 (0.02) Side View 5.1 (0.2) 1.0 +0.15/-0 ( 0.04 +0.006/-0) 17.5 (0.69) Derating Free Air Convection 71 C Output Power (%) 100 80 Safe Operating Area 60 40 20 0 - 20 - 40 0 20 40 60 80 85 100 Ambient Temperature C Typical Application Circuit +Vin C1 10uF GND 3 +Vout 1 AMSR2-78-NZ 2 C2 22uF GND C1: A low ESR capacitor is required to keep the noise of the converter to a minimum. Ceramic capacitors are recommended with typical value is 10F / 25V. C2: Installation of C2 is recommended with typical value of22F / 16V ceramic for 5V and 6.5V output signal and 22F / 6.3V ceramic for 2.5V and 3.3V output signal. NOTE: This part is not designed for parallel operation. www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 3 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AMSR2-78-NZ Up to 13 Watt | DC-DC Switching Regulator Dual Output Connection 3 1 +Vin AMSR2-78-NZ C1 10uF +Vout C2 2 22uF GND GND 3 1 AMSR2-78-NZ C1 C2 2 22uF 10uF -Vout Input Filter 10uH ~ 47uH 3 +Vout 1 C1 C1 10uF 10uF AMSR2-78-NZ C2 2 22uF GND GND Output Filter 10uH ~ 47uH 3 1 C1 AMSR2-78-NZ 10uF GND 2 +Vout C1 C1 10uF 10uF C2 22uF GND NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R12.G Tel: +1 514 620 2722 4 of 4 Toll free: + 1 888 9 AIMTEC (924 6832) North America only