TFT-LCD Supplies + DVR + VCOM Amplifier ISL98665 Features The ISL98665 is an integrated power management IC (PMIC) for TFT-LCDs used in notebooks, tablet PCs, and monitors. The device integrates a boost converter for generating AVDD, an LDO for VLOGIC, and a second boost converter for VGH. VGL is generated by a charge pump driven by the switch node of the AVDD boost. The ISL98665 also includes a high performance VCOM amplifier and a VCOM calibrator, with integrated EEPROM. * 2.2V to 5.5V input * 2.5A, 0.15 integrated AVDD boost FET * 1.2A integrated boost for up to 37.5V VGH with temperature compensation * LDO able to deliver 360mA * Adjustable boost switching frequency from 310kHz to 1.2MHz The AVDD boost converter features a 2.5A FET with adjustable switching frequency ranging from 310kHz to 1.2MHz. The soft-start time and compensation are adjustable by external components. * Integrated high output current VCOM amplifier * DVR (digital variable resistor) - Wiper position stored in 7-bit nonvolatile memory and recalled on power-up - Endurance, 1,000 data changes per bit VGH boost converter features a 1.2A FET and temperature compensation. The LDO is able to deliver 360mA for driving the voltage rail required by external digital circuitry. * UVLO, OVP, OCP, and OTP protection * 28 Ld, 4x5mm TQFN package The ISL98665 provides a 7-bit resolution, current sink VCOM calibrator with I2C interface, and a VCOM amplifier. The output of the VCOM is powered up with the voltage at the last programmed EEPROM setting. * Pb-Free (RoHS compliant) Applications * LCD Notebook, Tablet, and Monitor Pin Configuration COMP LX2 LX1 PGND4 PGND3 SDA SCL ISL98665 (28 LD 4x5 TQFN) TOP VIEW 28 27 26 25 24 23 22 SS 1 FB 2 21 RSET FREQ 3 20 NC AGND1 4 19 VGH THERMAL PAD EN 5 18 AGND2 VIN 6 17 RNTC LOUT 7 16 COMP2 AVDD 15 FBP June 27, 2013 FN8564.0 1 10 11 12 13 14 VOUT PGND1 PGND2 LXP POS 9 NEG 8 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2013. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. ISL98665 Table of Contents Pin Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Application/Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Typical Performance Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Applications Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching Frequency Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVDD Boost Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Soft-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGH Boost Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGH Temperature Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Boost Component Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Input Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rectifier Diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Output Capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linear Regulator (LDO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VCOM Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I2C Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Protocol Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ISL98665 DVR Memory Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Description: Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Register Description: IVR and WR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Initial VCOM Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Determination of RSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Determination of R1 and R2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Final Transfer Function for DVR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VGL Charge Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fault Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . overCURRENT PROTECTION (OCP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Undervoltage Lockout (UVLO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OVERVOLTAGE PROTECTION (OVP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OVER-Temperature PROTECTION (OtP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power On/OFF Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 10 10 10 10 10 11 11 11 11 12 12 12 12 13 13 14 14 14 15 15 15 17 18 18 19 19 19 19 19 19 19 19 Layout Recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Power-ON/OFF Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 About Intersil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Package Outline Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2 FN8564.0 June 27, 2013 ISL98665 Application/Block Diagram L1 VIN D1 AVDD C1 C2 C6 C7 C22 LX1 LX2 R5 EN R22 C10 VIN R18 C11 PGND3 AVDD BOOST CONTROLLER LDO CONTROLLER VLOGIC C23 R2 FB R17 SS RNTC RNTC R18 AVDD LXP OSC VGL Z1 C20 PGND4 LOUT C12 VLOGIC D3 AVDD C24 COMP R1 FREQ R28 C9 R3 AVDD AVDD L2 C15 C13 D2 VGH BOOST CONTROLLER VGH R15 POS PGND2 C17 VOUT FBP DVR C25 VCOM NEG R12 PGND1 COMP2 R14 R11 RSET R16 R8 VGH SCL EEPROM REGISTER SDA C21 AGND1 AGND2 THERMAL PAD NOTE: Component designators in this Application Diagram match with the evaluation board schematic. 3 FN8564.0 June 27, 2013 ISL98665 Pin Descriptions PIN# SYMBOL DESCRIPTION 1 COMP 2 FB AVDD boost converter feedback. Connect to the center of a voltage divider between AVDD and AGND to set the AVDD voltage. For more information refer to "AVDD Boost Operation" on page 10. 3 FREQ Boost Converter frequency adjustment pin. Connect this pin with a resistor to AGND set the boost frequency. Refer to "Switching Frequency Selection" on page 10 for more information. 4 AGND1 5 EN IC enable pin. Enables all the ISL98665 outputs. 6 VIN IC input supply and LDO input. Need to connect decoupling capacitor close to VIN pin. 7 LOUT 8 AVDD 9 POS VCOM Amplifier Non-inverting input. 10 NEG VCOM Amplifier Inverting input. 11 VOUT VCOM Amplifier output. 12 PGND1 VCOM Amplifier ground. 13 PGND2 VGH power ground. AVDD boost converter compensation pin. Connect a series resistor and capacitor between this pin and AGND to optimize transient response and stability. For more information refer to "Compensation" on page 12. Analog ground 1. LDO output. Connect at least one 1F capacitor to GND for stable operation. DVR and VCOM amplifier voltage analog supply. Place a 0.47F capacitor close to the AVDD pin. 14 LXP VGH boost converter switching node. 15 FBP VGH boost converter feedback. Connect to the center of a voltage divider between VGH and AGND to set the VGH voltage. Refer to "VGH Boost Operation" on page 10 for more information. 16 COMP2 VGH boost converter compensation pin. Connect a series resistor and capacitor between this pin and AGND to optimize transient response and stability. Refer to "Compensation" on page 12 for more information. 17 RNTC Temperature Compensation pin. Refer to "VGH Temperature Compensation" on page 11 for the connection of this pin. 18 AGND2 19 VGH Power supply for EEPROM programming; VGH OVP sensing pin. 20 NC Not connected. 21 RSET DVR sink current adjustment pin; connect a resistor between this pin and AGND to set the resolution of the DVR output voltage. 22 SS AVDD Boost Converter Soft-Start. Connect a capacitor between this pin and GND to set the soft-start time. Refer to "Soft-Start" on page 10 for more information. 23 SCL I2C clock high impedance input. 24 SDA I2C bidirectional data high impedance input/open-drain output. 25, 26 PGND3, PGND4 AVDD boost power ground. 27, 28 LX1, LX2 AVDD boost converter switching node 1 and 2. Thermal PAD Connect to ground plane on PCB to maximize thermal performance. Analog ground 2. Ordering Information PART NUMBER (Notes 1, 2, 3) PART MARKING TEMP RANGE (C) ISL98665IRTZ 98665 IRTZ -40 to +105 ISL98665IRT-EVZ ISL98665 Evaluation Board PACKAGE (Pb-free) 28 Ld 4x5 TQFN PKG. DWG. # L28.4x5C NOTES: 1. Add "-T*" suffix for tape and reel. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 3. For Moisture Sensitivity Level (MSL), please see device information page for ISL98665 For more information on MSL please see techbrief TB363. 4 FN8564.0 June 27, 2013 ISL98665 Absolute Maximum Ratings Thermal Information VGH and LXP to AGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +45V LX1, LX2, AVDD, POS, NEG, and VOUT to AGND . . . . . . . . . . -0.3 to +18V Voltage Between AGND and PGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5V All Other Pins to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to +6.0V ESD Rating Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 200V Charged Device Model (Tested per JESD22-C101). . . . . . . . . . . . . . . 1kV Latch Up (Tested per JESD78; Class II, Level A) . . . . . . . . . . . . . . . . 100mA Thermal Resistance (Typical) JA (C/W) JC (C/W) 28 Ld 4x5 TQFN Package (Notes 4, 5). . . . 39 9 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +150C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C Lead Temperature During Soldering . . . . . . . . . . . . . . . . . . . . . . . . +260C Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Ambient Operating Temperature . . . . . . . . . . . . . . . . . . . .-40C to +105C Supply Voltage VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2V to 5.5V AVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 16V VGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Up to 37.5V CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with "direct attach" features. See Tech Brief TB379. 5. For JC, the "case temp" location is the center of the exposed metal pad on the package underside. Electrical Specifications VIN= EN = 3.3V, AVDD = 8V, VLDO = 1.89V, VGH = 21V. TA = +25C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +105C. SYMBOL PARAMETER TEST CONDITIONS MIN (Note 6) TYP MAX (Note 6) UNITS 2.2 3.3 5.5 V GENERAL VIN IS_DIS VIN Supply Voltage Range VIN Supply Currents when Disabled VIN < UVLO 390 500 A IS VIN Supply Currents EN = 3.3V, overdrive AVDD and VGH 1.3 1.6 mA IEN Enable Pin Current EN = 3.3V 3 A LOGIC INPUT CHARACTERISTICS VIL Low Voltage Threshold EN, SCL, SDA 0.60 V VIH High Voltage Threshold EN, SCL, SDA 1.2 RIL Pull-Down Resistor EN 0.75 1.15 1.55 M FREQ resistor = 10k 1.1 1.2 1.3 MHz FREQ resistor = 20k 550 600 650 kHz 16 V V INTERNAL OSCILLATOR FOSC Switching Frequency AVDD BOOST REGULATOR AVDD_RNG AVDD Output Voltage Range 1.1*VIN DAVDD/ DIOUT AVDD Load Regulation 10mA < ILOAD < 250mA, TA = +25C 0.2 % DAVDD/ DVIN AVDD Line Regulation ILOAD = 150mA, 2.2V < VIN < 5.5V, TA = +25C 0.2 % VFB AVDD Feedback Voltage ILOAD = 100mA IFB Input Bias Current FB pin rDS(ON)_AVDD Switch ON-resistance ILIM_AVDD Switch Current Limit 5 1.188 2.0 1.200 1.212 V 200 nA 150 190 m 2.5 3.0 A FN8564.0 June 27, 2013 ISL98665 Electrical Specifications VIN= EN = 3.3V, AVDD = 8V, VLDO = 1.89V, VGH = 21V. TA = +25C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +105C. (Continued) SYMBOL AVDD_DMAX PARAMETER Max Duty Cycle TEST CONDITIONS FREQ = 600kHz MIN (Note 6) TYP 88 93 MAX (Note 6) UNITS % VGH BOOST REGULATOR VGH _RNG VGH Output Voltage Range ILIM_VGH VGH Switch Current Limit 1.1* AVDD 0.8 1.2 37.5 V 1.6 A DVGH/ DIOUT Load Regulation 2mA < ILOAD < 50mA, TA = +25C 0.2 % DVGH/ DVIN Line Regulation 2.2V < VIN < 5.5V, ILOAD = 5mA, TA = +25C 0.2 % rDS(ON)_VGH VGH Boost Switch ON Resistance VGH_DMAX Maximum Duty Cycle FREQ = 600kHz IFBP Input Bias Current FBP Pin VFBP VGH Feedback Voltage VRNTC < 0.608V, VGH < 37.5V 0.592 VRNTC > 1.215V, VGH< 37.5V 1.188 0.6 90 0.608V < VRNTC < 1.215V, VGH< 37.5V Hys_TCOMP IRNTC Temperature Compensation Hysteresis 0.8 94 % 200 nA 0.608 0.622 V 1.215 1.239 V VRNTC V 20 mV RNTC Current 200 nA LDO REGULATOR DVLDO/ DVIN Line Regulation ILOAD = 1mA, 2.2V < VIN < 5.5V, TA = +25C 0.3 % DVLDO/ DIOUT Load Regulation 1mA < ILOAD < 300mA, TA = +25C 0.3 % VDO Dropout Voltage VIN = 2.2V, ILOAD = 250mA 200 Current Limit Output drops by 5% LDO Output Voltage ILOAD = 50mA, TA = +25C VCOM Block Supply Current AVDD = 8V Offset Voltage VPOS = VNEG = 0.5*AVDD Input Leakage Current VPOS = VNEG = 0.5*AVDD ILIM_LDO VLDO 250 300 mV 360 mA 1.89 V VCOM AMPLIFIER IS_com VOS IL 0.7 0 mA 15 mV 1 A AVDD V CMIR Common Mode Input Voltage Range CMRR Common-Mode Rejection Ratio VPOS = VNEG from 2V to 6V 60 75 dB PSRR Power Supply Rejection Ratio 8V < AVDD < 12V VPOS = VNEG = 0.5*AVDD 70 85 dB Output Voltage Swing High IOUT (source) = 0.1mA AVDD 0.015 AVDD 0.005 V IOUT (source) = 75mA AVDD 1.74 AVDD 1.28 V VOH VOL Output Voltage Swing Low 6 0 1.35 IOUT (sink) = 0.1mA GND + 0.001 GND + 0.006 V IOUT (sink) = 75mA GND + 0.94 GND + 1.4 V FN8564.0 June 27, 2013 ISL98665 Electrical Specifications VIN= EN = 3.3V, AVDD = 8V, VLDO = 1.89V, VGH = 21V. TA = +25C, unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +105C. (Continued) SYMBOL ISC SR BW MIN (Note 6) TYP VOUT = AVDD, VOUT shorted to GND (Sourcing) 135 180 mA VOUT = GND, VOUT shorted to AVDD (Sinking) 170 220 mA Rising, 0.5V VOUT +5.5V, RL = 10k || CL = 10pF to AGND 35 V/s Falling, +5.5V VOUT 0.5V, RL = 10k || CL = 10pF to AGND 35 AV 1, RL = 10k || CL = 10pF to AGND 20 MHz 7 Bits PARAMETER Output Short Circuit Current Slew Rate Bandwidth (-3dB) TEST CONDITIONS MAX (Note 6) UNITS VCOM CALIBRATOR (DVR) RSETVR RSET Voltage Resolution (Note 7) RSETDNL RSET Differential Nonlinearity TA = +25C, (Note 8) 1 LSB RSETZSE RSET Zero-Scale Error TA = +25C, (Note 8) 2 LSB RSETFSE RSET Full-Scale Error TA = +25C, (Note 8) 8 LSB IRSET AVDD to RSET RSET Current Capability 105 AVDD to RSET Voltage Attenuation A 1.20 V/V FAULT DETECTION THRESHOLD VUVLO Undervoltage Lock out Threshold VIN rising 1.85 Hysteresis OVPAVDD AVDD Boost Overvoltage Protection AVDD rising (Note 9) TOFF 2.15 0.2 15.4 Hysteresis OVPVGH 2.0 15.9 V 16.4 1.3 38 39 V V V VGH Boost Overvoltage Protection VGH rising 40 V Thermal Shutdown all Channels Temperature rising 150 C Hysteresis 40 C 0.45 ms 4 A 1 V POWER SEQUENCE tssVLOGIC VLOGIC Soft-start Time Iss AVDD Boost Soft-start Current at Start-Up Vss Soft-Start Voltage End of soft-start ramp Delay from AVDD start-up finish to VGH Start VGH = 37.5V 2.5 ms VGH Soft-Start Time VGH = 37.5V 33 ms EEPROM Endurance TA = +25C, 1 kCyc EEPROM Retention TA = +25C, 88 kHrs tdelayVGH tssVGH EEPROM NOTES: 6. Parameters with MIN and/or MAX limits are 100% tested at +25C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 7. Established by design. Not a parametric spec. 8. Compliance to limits is assured by characterization and design. 9. Boost will stop switching as soon as boost output reaches OVP threshold. 7 FN8564.0 June 27, 2013 ISL98665 Typical Performance Curves 0.01 90 LOAD REGULATION (%) EFFICIENCY (%) 86 84 Fosc = 310kHz Fosc = 600kHz 82 80 Fosc = 1.2MHz VIN = 3.3V, AVDD = 8V INDUCTOR = NRS5010T, 10H DIODE = PMEG2005 78 76 VIN = 3.3V, AVDD = 8V 0.00 88 0 50 100 150 200 -0.01 -0.02 Fosc = 310kHz -0.03 -0.04 -0.05 Fosc = 600kHz -0.06 Fosc = 1.2MHz -0.07 -0.08 -0.09 10 250 60 110 I_AVDD (mA) FIGURE 1. AVDD EFFICIENCY vs I_AVDD 0.020 210 260 FIGURE 2. AVDD LOAD REGULATION VIN = 3.3V, AVDD = 8V, I_AVDD = 150mA VIN = 3.3V, AVDD = 8V, I_AVDD = 50mA-250mA 0.015 LINE REGULATION (%) 160 I_AVDD (mA) 0.010 0.005 Fosc = 310kHz 0.000 Fosc = 1.2MHz -0.005 Fosc = 600kHz -0.010 -0.015 AVDD RIPPLE = .200mV/DIV, I_AVDD = 100mA/DIV -0.020 2.2 2.7 3.2 3.7 4.2 4.7 2ms/DIV 5.2 AVDD BOOST VIN (V) FIGURE 3. AVDD LINE REGULATION 0.000 85 0.002 Fosc = 600kHz 75 Fosc = 1.2MHz 70 65 60 Fosc = 310kHz AVDD = 8V, VGH = 21V INDUCTOR = NRS5010T, 10H DIODE = PMEG4005 55 50 0 5 10 15 20 25 30 35 40 I_VGH (mA) FIGURE 5. VGH EFFICIENCY vs I_VGH 8 45 LOAD REGULATION (%) 90 80 EFFICIENCY (%) FIGURE 4. AVDD TRANSIENT RESPONSE VIN = 8V, VGH = 21V Fosc = 600kHz 0.004 -0.006 -0.008 -0.010 -0.012 -0.014 Fosc = 1.2MHz Fosc = 310kHz -0.016 50 -0.018 0 5 10 15 20 25 30 I_VGH (mA) 35 40 45 50 FIGURE 6. VGH LOAD REGULATION FN8564.0 June 27, 2013 ISL98665 Typical Performance Curves (Continued) 0.016 LINE REGULATION (%) 0.014 IC_VIN = 3.3V, AVDD = 8V, VGH = 21V I_VGH = 2mA-20mA Fosc = 600kHz 0.012 0.010 0.008 Fosc = 1.2MHz 0.006 VGH Ripple= 200mV/DIV, I_VGH = 10mA/DIV 0.004 IC_VIN = 3.3V, VGH = 21V I_VGH = 5mA 0.002 0.000 -0.002 Fosc = 310kHz 0 2 4 6 8 10 12 14 16 18 20 2ms/DIV VGH BOOST VIN (V) FIGURE 7. VGH LINE REGULATION FIGURE 8. VGH TRANSIENT RESPONSE 0.000 LOAD REGULATION (%) VIN = 3.3V, AVDD = 8V VGH = 37.5V I_VGH = 2mA-20mA VGH Ripple = 200mV/DIV, I_VGH = 10mA/DIV -0.050 -0.100 -0.150 -0.200 -0.300 2ms/DIV VIN = 3.3V -0.250 0 50 100 150 200 250 300 I_LDO (mA) FIGURE 10. LDO LOAD REGULATION FIGURE 9. VGH TRANSIENT RESPONSE 0.000 INPUT = 1V/DIV, OUTPUT = 1V/DIV LINE REGULATION (%) -0.050 OUTPUT SIGNAL -0.100 -0.150 -0.200 ILDO = 1mA -0.250 -0.300 2.0 2.5 3.0 INPUT SIGNAL 3.5 4.0 4.5 5 5.5 6.0 500ns/DIV VIN (V) FIGURE 11. LDO LINE REGULATION 9 FIGURE 12. VCOM LARGE SIGNAL TRANSIENT RESPONSE FN8564.0 June 27, 2013 ISL98665 Applications Information Enable Control The ISL98665 is enabled when the EN pin voltage is high and VIN is above rising UVLO. All output channels in ISL98665 are shut down when the enable pin is pulled down. Switching Frequency Selection The ISL98665 switching frequency can be adjusted from 310kHz to 1.2MHz by connecting a resistor between FREQ pin and AGND. A lower switching frequency reduces power dissipation at very light load conditions but more easily allows discontinuous conduction mode. Higher switching frequency allows for smaller external components - inductor and output capacitors. Higher switching frequency will get higher efficiency for a given VIN and loading range, depending on VIN, VOUT and external components, as shown in Figure 1. The calculation of the switching frequency is shown in Equation 1 10 ( 1.14 x10 ) f SW = -------------------------------R FSW (EQ. 1) fSW is the desired boost switching frequency, and RFSW is the setting resistor (see R8 in Application Diagram on page 3). Figure 13 shows the relationship between the switching frequency and the frequency setting resistance. An external resistor divider is required to divide the output voltage down to the nominal reference voltage. Current drawn by the resistor network should be limited to maintain the overall converter efficiency. The maximum value of the resistor network is limited by the feedback input bias current and the potential for noise being coupled into the feedback pin. A resistor network in the order of 60k is recommended. The boost converter output voltage is determined by Equation 3: R2 + R3 V AVDD = --------------------- x V FB R3 (EQ. 3) R2 and R3 are the feedback resistor values as shown in the "Application/Block Diagram" on page 3. The current through the MOSFET is limited to 2.5A peak. This restricts the maximum output current (average) based on Equation 4: I L V IN I OMAX = I LMT - -------- x --------- xEff 2 VO (EQ. 4) Eff is the efficiency of the AVDD boost converter, IL is the peak-to-peak inductor ripple current, and is set by Equation 5: 1400 V IN D I L = --------- x ---------L f SW 1200 FREQUENCY (kHz) The boost regulator uses a summing amplifier architecture consisting of gm stages for voltage feedback, current feedback and slope compensation. A comparator looks at the peak inductor current cycle-by-cycle and terminates the PWM cycle if the current limit is reached. 1000 (EQ. 5) 800 where fSW is the switching frequency. 600 SOFT-START 400 The soft-start is provided by an internal current source of 4A to charge the external soft-start capacitor. The ISL98665 ramps up the current limit from 0A up to the full value, as the voltage at the SS pin ramps from 0V to 1V. Hence, the soft-start time shown in Figure 24 on page 21 is 5.5ms when the soft-start capacitor is 22nF, and 11.8ms for 47nF. 200 0 5 10 15 20 25 30 35 40 45 50 55 RESISTANCE (k) FIGURE 13. AVDD SWITCHING FREQUENCY vs RESISTANCE AVDD Boost Operation The AVDD boost converter is a current mode PWM converter operating at frequency ranging from 310kHz or 1.2MHz. It can operate in both discontinuous conduction mode (DCM) at light load and continuous conduction mode (CCM). In continuous conduction mode, current flows continuously in the inductor during the entire switching cycle in steady state operation. The voltage conversion ratio in continuous current mode is given by Equation 2: V AVDD 1 ------------------- = ------------1-D V IN (EQ. 2) D is the duty cycle of the switching MOSFET. 10 VGH Boost Operation The VGH boost converter is a current mode PWM converter operating at frequency ranging from 310kHz or 1.2MHz, which is the same with AVDD boost switching frequency. It can operate in both discontinuous conduction mode (DCM) at light load and continuous conduction mode (CCM) at heavy load. The VGH boost regulator uses a summing amplifier architecture consisting of gm stages for voltage feedback, current feedback and slope compensation. A comparator looks at the peak inductor current cycle-by-cycle and terminates the PWM cycle if the current limit is reached. An external resistor divider is required to divide the output voltage down to the nominal reference voltage. Current drawn by the resistor network should be limited to maintain the overall converter efficiency. The maximum value of the resistor network is limited by the feedback input bias current and the potential for FN8564.0 June 27, 2013 ISL98665 noise being coupled into the feedback pin. The boost converter output voltage is determined by Equation 6: R 14 + R 15 V GH = ---------------------------- x V FBP R 14 (EQ. 6) Where R14 and R15 are feedback resistors as shown in the "Application/Block Diagram" on page 3 The current through the MOSFET is limited to 1.2A peak. In continuous conduction mode, current flows continuously in the inductor during the entire switching cycle in steady state operation. The voltage conversion ratio in continuous current mode is given by Equation 7: V GH 1 ------------ = ------------1-D V IN The VGH feedback voltage (thus VGH output voltage) is adjusted by the RNTC voltage, which is varied by the NTC thermistor resistance at different temperature, as shown in Figure 15. When the VGH voltage is below the OVP threshold, if RNTC voltage is below 0.608V at higher temperature, the VGH feedback voltage is fixed at 0.608V. If RNTC voltage is above 1.215V at lower temperature, the VGH feedback voltage is fixed at 1.215V. If RNTC voltage is between 0.608V and 1.215V, the VGH feedback voltage follows RNTC voltage. Once VGH output voltage is above OVP threshold, the VGH output voltage will be regulated at 37.5V no matter what RNTC voltage is. 1.60 1.20 For most of the applications, the VGH boost converter operates in discontinuous conduction mode. The operation of boost converter in DCM is much more complicated than in CCM. The voltage conversion ratio is now a function not only of the duty cycle D, but also of the boost inductance, the switching frequency and the loading. In DCM, the voltage conversion ratio is given by Equation 8. xD 2 V GH V IN ----------- = 1 + ----------------------------------V IN I OUT x2xLxf s (EQ. 8) where fS is the switching frequency, VIN is the input voltage of VGH boost, IOUT is the loading of VGH boost converter. VGH TEMPERATURE COMPENSATION Temperature compensation is integrated in ISL98665 to adjust VGH output voltage in order to compensate the amorphous silicon (a-Si) shift register driving capability over temperature. A voltage divider with a NTC thermistor between AVDD and ground should be used to determine the RNTC voltage, as shown in Figure 14. R17 and R18 can be adjusted to select the temperature range, based on the selection of the NTC thermistor. VLOGIC R17 VOLTAGE (V) (EQ. 7) where D is the duty cycle of the switching MOSFET, VIN is the input voltage of VGH boost. In most applications, VIN of the VGH boost converter is connected to the AVDD. NTC = NCP15XM472 R17 = 5.11k, R18 = 28k 1.40 1.215V 1.00 VFB 0.80 0.608V 0.60 0.40 0.20 0.00 VRNTC -10 -20 0 10 20 30 40 50 60 TEMPERATURE (C) FIGURE 15. VFBP/VRNTC vs TEMPERATURE NOTES: 10. Above FBP vs Temperature curve is only true when VGH = VFBP*(RU+RL) / RL < OVP where RU is the upper resistance (R15 in "Application/Block Diagram" on page 3) and RL is the lower resistance (R14 in Application Diagram on page 3) in the FBP resistor ladder from VGH to AGND. 11. When VGH reach OVP, VGH boost regulates at 37.5V, regardless RNTC voltage. Boost Component Selection INPUT CAPACITOR An input capacitor is used to suppress the voltage ripple injected into the boost converter. A ceramic capacitor is recommended. The voltage rating of the input capacitor should be larger than the maximum input voltage. Some input capacitors are recommended in Table 1. TABLE 1. BOOST CONVERTER INPUT CAPACITOR RECOMMENDATION CAPACITOR SIZE MFG PART NUMBER 10F/10V 0603 TDK C1608X5R1A106M 10F/16V 0805 TDK C2012X5R1C106k/0.85 INDUCTOR RNTC NTC R18 The boost inductor is a critical part that influences the output voltage ripple, transient response, and efficiency. Values of 3.3H to 10H are used to match the internal slope compensation. If boost converter operates in CCM, the inductor must be able to handle the following average and peak currents shown in Equations 9 and 10: FIGURE 14. RNTC CIRCUIT 11 FN8564.0 June 27, 2013 ISL98665 2. Charging and discharging of the output capacitor. I OUT VOUT I LAVG = ------------- x -----------------Eff V IN (EQ. 9) IO V O - V IN 1 V RIPPLE = I LPK x ESR + ------------------------ x ---------------- x ---f C V O I L I LPK = I LAVG + -------2 (EQ. 10) Where IL can be calculated using Equation 5. If boost converter operates in DCM, the inductor must be able to handle the following average and peak currents shown in Equations 11 and 12: I OUT VGH I LAVG = ------------- x ------------Eff V IN (EQ. 11) V IN D I LPK = --------- x ---L fs OUT (EQ. 13) s For low ESR ceramic capacitors, the output ripple is dominated by the charging and discharging of the output capacitor. The voltage rating of the output capacitor should be greater than the maximum output voltage. Note: Capacitors have a voltage coefficient that makes their effective capacitance drop as the voltage across them increases. COUT in Equation 13 assumes the effective value of the capacitor at a particular voltage and not the manufacturer's stated value, measured at 0V. Some inductors are recommended in Table 2 for different design considerations. It is recommended to use one or two 10F X5R 25V or equivalent ceramic output capacitors for AVDD boost output and 4.7F X5R 50V or equivalent ceramic output capacitors for VGH boost output. RECTIFIER DIODE Table 4 shows some selections of output capacitors. (EQ. 12) A high-speed diode is necessary due to the high switching frequency. Schottky diodes are recommended because of their fast recovery time and low forward voltage. The reverse voltage rating of this diode should be higher than the maximum output voltage. The rectifier diode must meet the output current and peak inductor current requirements. Table 3 shows some recommendations for boost converter diode. TABLE 2. BOOST CONVERTER INDUCTOR RECOMMENDATION INDUCTOR DIMENSIONS (mm) 10H/ 4Apeak 8.3x8.3x4.5 6.8H/ 1.8Apeak 5.0x5.0x2.0 10H/ 0.9A 5.0x5.0x1.0 PART NUMBER MFG NOTE Sumida CDRH8D43-100NC TDK Efficiency Optimization PLF5020T-6R8M1R8 Taiyo NRS5010T100MMGF PCB Yuden space/profile optimization TABLE 3. BOOST CONVERTER RECTIFIER DIODE RECOMMENDATION DIODE V /I R AVG RATING PACKAGE MFG AVDD PMEG2010ER 20V/1A SOD123W NXP MSS1P2U 20V/1A MicroSMP VISHAY BAS52-02V 45V/0.75A SOD523F INFINEON DB2J501 50V/0.2A SOD323 PANASONIC VGH TABLE 4. BOOST OUTPUT CAPACITOR RECOMMENDATION CAPACITOR SIZE MFG PART NUMBER 4.7F/25V 0805 TDK 10F/25V 0805 Murata 4.7F/50V 0805 TDK C2012X5R1H475M 1F/50V 0603 TDK CGA3E3X5R1H105K AVDD C2012X5R1E475K GRM21BR61E106KA73L VGH COMPENSATION The boost converters of the ISL98665 can be compensated by an RC network connected from the COMP pins to ground. For AVDD, 15nF and 5.5k RC network is used in the demo board. For VGH , 15nF and 28k RC network is used in the demo board. The larger value resistor and lower value capacitor can lower the transient overshoot, however, at the expense of the stability of the loop. Linear Regulator (LDO) The ISL98665 includes an LDO with fixed output voltage of 1.89V. It can supply current up to 350mA. The efficiency of the LDO depends on the difference between input voltage and output voltage (Equation 14) by assuming LDO quiescent current is much lower than LDO output current: V LDO_IN ( % ) = ------------------------------ x 100% V LDO_OUT (EQ. 14) The less difference between input and output voltage, the higher efficiency it is. OUTPUT CAPACITOR The output capacitor supplies current to the load during transient conditions directly and reduces the ripple voltage at the output. Output ripple voltage consists of two components: 1. The voltage drop due to the inductor ripple current flowing through the ESR of the output capacitor. 12 Ceramic capacitors are recommended for the LDO input and output capacitors. An output capacitor within the 1F to 4.7F range is recommended. Larger capacitors help to reduce noise and deviation during transient load change. Some capacitors are recommended in Table 5. FN8564.0 June 27, 2013 ISL98665 TABLE 5. LDO OUTPUT CAPACITOR RECOMMENDATION CAPACITOR SIZE MFG PART NUMBER 1F/10V 0603 TDK C1608X7R1A105K 1F/6.3V 0603 MURATA GRM188R70J105K 2.2F/6.3V 0603 TDK C1608X7R0J225K VCOM Amplifier The VCOM amplifier is designed to control the voltage on the back plane of an LCD display. This plane is capacitively coupled to the pixel drive voltage, which alternately cycles positive and negative at the line rate for the display. Thus, the amplifier must be capable of sourcing and sinking pulses of current, which can occasionally be quite large (in the range of 100mA for typical applications). The ISL98665 VCOM amplifier is capable of rail-to-rail output swings and can drive wide range of capacitive loads. As load capacitance increases, the -3dB bandwidth of the device will decrease and the peaking will increase. When driving large capacitive loads, an isolation resistor (typically between 1 and 10) should be placed in series with the output. I2C Serial Interface The ISL98665 uses a standard I2C interface bus for communication. The two-wire interface links a Master(s) and uniquely addressable Slave devices. The DVR of the ISL98665 operates as a slave device in all applications. The Master generates clock signals and is responsible for initiating data transfers. The serial clock is on the SCL line and the serial data (bi-directional) is on the SDA line. The ISL98665 supports clock rates up to 400kHz (Fast-Mode), and is backwards compatible with standard 100kHz clock rates (Standard-mode). The SDA and SCL lines must be HIGH when the bus is not in use. An external pull-up resistor (typically 2.2k to 4.7k) is required for SDA and SCL. The ISL98665 meets standard I2C timing and interface specifications, see Table 6 and Figure 16, which show the standard timing definitions and specifications for I2C communication. The positive input of the VCOM amplifier (POS) is controlled by the DVR DAC. However, if the DVR DAC calibration function is not required, the VCOM amplifier can be used as an independent operational amplifier. Leave the RSET pin floating to disable the DVR DAC function. TABLE 6. I2C TIMING AND INTERFACE SPECIFICATIONS SYMBOL MAX UNITS SCL Frequency 400 kHz tiN Pulse Width Suppression Time at SDA and SCL Inputs 50 ns tAA SCL Falling Edge to SDA Output Data Valid 480 ns tBUF Time the Bus Must be Free Before the Start of a New Transmission 480 ns tLOW Clock LOW Time 480 ns tHIGH Clock HIGH Time 400 ns tSU:STA START Condition Set-up Time 480 ns tHD:STA START Condition Hold Time 400 ns tSU:DAT Input Data Set-up Time 40 ns tHD:DAT Input Data Hold Time 0 ns tSU:STO STOP Condition Set-up Time 400 ns tHD:STO STOP Condition Hold Time for Read, or Volatile Only Write 400 ns fSCL PARAMETER MIN TYP tWp Non-Volatile Write Cycle Time 25 ms CSCL Capacitive on SCL 5 pF CSDA Capacitive on SDA 5 pF 13 FN8564.0 June 27, 2013 ISL98665 tBUF VIH SDA VIL tSU:STA tr tHD:STA tf tr tSU:STO tf VIH SCL VIL START tSU:DAT tHD:DAT STOP START FIGURE 16. I2C TIMING DEFINITION PROTOCOL CONVENTIONS Data states on the SDA line can change only during SCL LOW periods. The SDA state changes during SCL HIGH are reserved for indicating START and STOP conditions (see Figure 16). On power-up of the ISL98665, the SDA pin is in the input mode. A valid Identification Byte contains 28h as the seven MSBs. The LSB is in the Read/Write bit. Its value is "1" for a Read operation, and "0" for a Write operation (see Table 7). TABLE 7. IDENTIFICATION BYTE FORMAT 0 1 0 1 0 0 0 R/W All I2C interface operations must begin with a START condition, which is a HIGH-to-LOW transition of the SDA while SCL is HIGH. The DVR continuously monitors the SDA and SCL lines for the START condition and does not respond to any command until this condition is met (see Figure 16). A START condition is ignored during the power-up sequence and during internal non-volatile write cycles. WRITE OPERATION All the I2C interface must be terminated by a STOP condition, which is a LOW-to-HIGH transition of SDA while SCL is high (see Figure 16). A STOP condition at the end of a read operation, or at the end of a write operation to volatile bytes only places the device in its standby mode. A STOP condition during a write operation to a non-volatile write byte, initiates an internal non-volatile write cycle. The device enters its standby state when the internal non-volatile write cycle is completed. A STOP condition also acts as a protection of non-volatile memory. A valid Identification Byte, Address Byte, and total number of SCL pulses act as a protection of both volatile and non-volatile registers. An ACK (Acknowledge) is a software convention used to indicate a successful data transfer. The transmitting device, either master or slave, releases the SDA bus after transmitting eight bits. During the ninth clock cycle, the receiver pulls the SDA line LOW to acknowledge the reception of the eight bits of data (see Figure 17). The ISL98665 DVR responds with an ACK after recognition of a START condition followed by a valid Identification Byte, and once again after successful receipt of an Address Byte. The ISL98665 also respond with an ACK after receiving a Data Byte of a write operation. The master must respond with an ACK after receiving a Data Byte of a read operation. 14 (MSB) (LSB) A write operation requires a START condition, followed by a valid Identification Byte, a valid Address Byte, a Data Byte, and a STOP condition (see Figure 17). After each of the three bytes, the ISL98665 responds with an ACK. When the Write transaction is completed, the Master should generate a STOP condition. During a Write sequence, the Data Byte is loaded into an internal shift register as it is received. The Data Byte is transferred to the WR or to the ACR respectively, at the falling edge of the SCL pulse that loads the last bit (LSB) of the Data Byte. READ OPERATION A read operation consists of a three byte instruction followed by one or more Data Bytes (see Figure 19). The master initiates the operation issuing the following sequence: a START, the Identification byte with the R/W bit set to "0", an Address Byte, a second START, and a second Identification byte with the R/W bit set to "1". After each of the three bytes, the ISL98665 responds with an ACK; then the ISL98665 transmits the Data Byte. The master then terminates the read operation (issuing a STOP condition) following the last bit of the Data Byte. FN8564.0 June 27, 2013 ISL98665 ISL98665 DVR Memory Description Register Description: Access Control The ISL98665 contains one non-volatile byte known as the Initial Value Register (IVR). It is accessed by the I2C interface at Address 00h. The IVR contains the value that is loaded into the Volatile Wiper Register (WR) at power-up. The Access Control Register (ACR) is volatile and is at address 02h. The MSB of ACR decides which byte is accessed at register 00h as shown in the following. All other bits of ACR should be zero (0). The volatile WR, and the non-volatile IVR of the DVR are accessed with the same address 00h. The Access Control Register (ACR) determines which byte at address 00h is accessed (IVR or WR). The volatile ACR must be set as follows: When the ACR is 00h, which is the default at power-up: * A read operation to address 00h outputs the value of the non-volatile IVR. * A write operation to address 00h writes the identical values to the WR and IVR of the DVR. When the ACR is 80h: * A read operation to address 00h outputs the value of the volatile WR. * A write operation to address 00h only writes to the volatile WR. It is not possible to write to the IVR without writing the same value to the WR. 00h and 80h are the only values that should be written to address 02h. All other values are reserved and must not be written to address 02h. TABLE 8. REGISTER MAP ADDRESS (HEX) NON-VOLATILE 02 - 01 00 VOLATILE ACR Reserved IVR NOTE: WR: Wiper Register, IVR: Initial value Register. 15 WR * 00h = Nonvolatile IVR * 80h = Volatile WR All other bits of he ACR should be written 0 or 1. Power-up default for this address is 00h. Register Description: IVR and WR The output of the DVR is controlled directly by the WR. Writes and reads can be made directly to this register to control and monitor without any non-volatile memory changes. This is done by setting address 02h to data 80h, then writing the data. The non-volatile IVR stores the power-up value of the DVR output. On power -up, the contents of the IVR are transferred to the WR. To write to the IVR, first address 02h is set to data 00h, then the data is written. Writing a new value to the IVR register will set a new power- up position for the wiper. Also, writing to this register will load the same value into the WR as the IVR. Therefore, if a new value is loaded into the IVR, not only will the non-volatile IVR change, but the WR will also contain the same value after the write, and the wiper position will change. Reading from the IVR will not change the WR, if its contents are different. Figure 20 gives examples to show writing to IVR/WR and reading from IVR/WR. Note: If the Data Byte is to be written only to WR, when the Write transaction is completed, the device enters its standby state. If the Data Byte is to be written also to non-volatile memory (IVR), when the Write transaction is completed, the ISL98665 begins its internal write cycle to non-volatile memory. During the internal non-volatile write cycle, the device ignores transitions at the SDA and SCL pins and the SDA output is at a high impedance state. When the internal non-volatile write cycle is completed, the ISL98665 enters its standby state. FN8564.0 June 27, 2013 ISL98665 SCL FROM MASTER 1 8 9 SDA OUTPUT FROM TRANSMITTER HIGH IMPEDANCE HIGH IMPEDANCE SDA OUTPUT FROM RECEIVER START ACK FIGURE 17. ACKNOWLEDGE RESPONSE FROM RECEIVER SIGNALS FROM THE MASTER SIGNAL AT SDA S T A R T WRITE IDENTIFICATION BYTE 0 1 0 1 0 0 0 SIGNALS FROM THE SLAVE ADDRESS BYTE S T O P DATA BYTE 0 0 0 0 0 0 X 0 0 A C K A C K A C K FIGURE 18. BYTE WRITE SEQUENCE SIGNALS FROM THE MASTER S T A R T SIGNAL AT SDA IDENTIFICATION BYTE WITH R/W = 0 0 1 0 1 0 0 0 0 A C K SIGNALS FROM THE SLAVE ADDRESS BYTE S T A IDENTIFICATION R BYTE WITH T R/W = 1 0 0 0 0 0 0 X 0 0 1 0 1 0 0 0 A C K S T O P A C K 1 A C K A C K FIRST READ DATA BYTE LAST READ DATA BYTE FIGURE 19. READ SEQUENCE 16 FN8564.0 June 27, 2013 ISL98665 Writing a new value to the IVR Write to ACR first 0 1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 0 0 0 0 0 0 0 0 A 0 1 0 0 0 0 A 0 0 0 0 0 0 0 0 A 0 D7 D6 D5 D4 D3 D2 D1 A Then, write to IVR 0 1 Note that the WR will also reflect this new value since both registers get writen at the same time D1:LSB, D7:MSB Writing a new value to WR only Write to ACR first 0 1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 1 0 0 0 0 0 0 0 A 0 1 0 0 0 0 A 0 0 0 0 0 0 0 0 A 0 D7 D6 D5 D4 D3 D2 D1 A 0 0 0 0 0 0 0 0 A 1 0 0 0 0 0 0 0 A Then, write to WR 0 1 Note that the IVR value will NOT change D1:LSB, D7:MSB Reading from IVR Write to the ACR first 0 1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 0 1 0 0 0 0 A 0 0 0 0 0 0 0 0 A 0 1 0 0 0 1 A 0 D7 D6 D5 D4 D3 D2 D1 0 1 0 0 0 0 A 0 0 0 0 0 0 1 0 A 0 1 0 0 0 0 A 0 0 0 0 0 0 0 0 A 0 1 0 0 0 1 A 0 D7 D6 D5 D4 D3 D2 D1 Then set the IVR address 0 1 Read from the IVR 0 1 Example 2 Reading from the WR Write to the ACR first 0 1 Then set the WR address 0 1 Read from the WR 0 1 FIGURE 20. EXAMPLE OF WRITE AND READ SEQUENCE FOR VCOM AMPLIFIER Initial VCOM Setting AVDD The ISL98665 provides the ability to reduce the flicker of a TFT-LCD panel during panel production test and alignment. It offers an I2C programmable adjustment, which can be used to set the panel VCOM voltage. The device has a 128-step "digital variable resistor" (DVR) control that adjusts an internal voltage that ultimately controls the sink current (ISET) output of the DVR_OUT node. The DVR_OUT pin is connected to an external voltage divider so that the device will have the capability to scale the voltage by increasing the DVR_OUT sink-current. The resistor on the SET pin (RSET) determines the maximum (full scale) allowable sink-current, which determines the adjustment resolution (step size), as shown in Figure 21. Note: That R1 in Figure 21 corresponds to R11 in the "Application/Block Diagram" on page 3. The R2 in Figure 21 corresponds to R12 in the "Application/Block Diagram" on page 3. 17 AVDD R1 R2 POS DVR_OUT NEG + VOUT ISET DVR_DAC RSET RSET FIGURE 21. DVR_OUTPUT CIRCUIT CONNECTION EXAMPLE FN8564.0 June 27, 2013 ISL98665 Figure 22, shows the relationship between the 7-bit DVR DAC register value and the DVR's tap position. The taps are generated from a resistor string between AVDD and GND. Note: That a register value of 0 register value of 0 selects the first step of the resistor string. The output voltage of the internal DVR string is given in Equation 15. 127 - RegisterValue A VDD V DVR = ----------------------------------------------------------- ---------------- 20 128 Equation 15 can also be used to calculate the unit sink current step size per Register Code, resulting in Equation 18: A VDD I STEP = ----------------------------------------------( 128 ) ( 20 ) ( R SET ) (EQ. 18) (EQ. 15) R1 ISET AVDD r A VDD POS/ DVR_OUT REGISTER VALUE (DECIMAL) R2 VCOM AMPLIFIER 19R A VDD VDVR VOUT Q1 20 0 A2 VCOM A1 1 VSAT 2 GND 3 R NEG V DVR RSET ISET 124 125 VRSET = VDVR = ISET * RSET RSET FIGURE 23. DVR CURRENT SINK CIRCUIT 126 DETERMINATION OF RSET 127 FIGURE 22. DVR DAC - SIMPLIFIED SCHEMATIC Figure 23, shows the schematic of the DVR_OUT current sink. The combination of amplifier A1, transistor Q1, and resistor RSET forms a voltage-controlled current source, with the voltage determined by the DVR setting. The initial register value is at 64d by default. The WR value is set back to 64d if any error occurs during I2C read or write communication. When writing to the EEPROM, VGH needs to be higher than 12V when AVDD is 8V. Outside these conditions, writing operations may not to be successful. The external RSET resistor sets the full-scale (maximum) sink current that can be pulled from the DVR_OUT node (ISET). The ISET can be up to 105A maximum (this limit is set by the size of the internal metal interconnects). The relationship between the ISET and the register value is shown in Equation 16. V DVR 127 - RegisterValue A VDD 1 I SET = ---------------- = ----------------------------------------------------------- ---------------- --------------- 20 R 128 R SET SET (EQ. 16) The maximum value of ISET can be calculated by substituting the maximum register value of 0 into Equation 16, resulting in Equation 17: A VDD 127 I SET ( MAX ) = ---------- x ---------------------128 20R SET (EQ. 17) 18 The ultimate goal for the DVR DAC is to generate an adjustable voltage between two endpoints, VCOM_MIN and VCOM_MAX, with a fixed power supply voltage, AVDD. This is accomplished by choosing the correct values for RSET, R1 and R2. The exact value of RSET is not critical. RSET values range from 3k to more than 100k will work under most conditions. Equation 17 can be used to calculate the minimum value RSET. Larger RSET values reduce quiescent power, since R1 and R2 are proportional to RSET. Equation 19 limits the minimum value for RSET, which is based on the 105A maximum output current sink. AVDD R SET > -----------------------------------( 20 x 105 )A (EQ. 19) DETERMINATION OF R1 AND R2 With AVDD, VCOM (MIN) and VCOM (MAX) known and RSET chosen per the above requirements, R1 and R2 can be determined using Equations 20 and 21: V COM ( MAX ) - V COM ( MIN ) R 1 = 20.16 R SET ------------------------------------------------------------------------ V COM ( MAX ) (EQ. 20) V COM ( MAX ) - V COM ( MIN ) R 2 = 20.16 R SET ------------------------------------------------------------------------ A VDD - V COM ( MAX ) (EQ. 21) FN8564.0 June 27, 2013 ISL98665 FINAL TRANSFER FUNCTION FOR DVR Fault Protection The voltage at POS/DVR_OUT can be calculated from Equation 22: OVERCURRENT PROTECTION (OCP) R2 127 - RegisterValue R 1 V DVROUT = A VDD --------------------- 1 - ----------------------------------------------------------- ---------------------- 128 20R SET R1 + R2 (EQ. 22) With amplifier A2 (VCOM Amplifier) in the unity-gain configuration (VOUT tied to NEG as shown in Figure 23), then POS = NEG = VOUT. Note: There can be a minor variance between POS and VOUT voltages due to the VCOM amplifier offset, refer to the VCOM amplifier "VOS" specification in the "Electrical Specifications Table" on page 6. VGL Charge Pump An external charge pump driven by the AVDD boost switching node can be used to generate VGL, as shown on the "Application/Block Diagram" on page 3. The number of the charge pump stages can be calculated using Equation 23. VGL HEADROOM = NxAVDD - 2xNxV d - VGL > 0 (EQ. 23) Where N is the number of the charge pump stages, Vd is the forward voltage drop of one Schottky diode used in the charge pump. Vd is varied with forward current and ambient temperature, so it should be the maximum value in the datasheet of the diode chosen according to max forward current and lowest temperature in the application condition. Once the number of the charge pump stages is determined, the maximum current that the charge pump can deliver can be calculated using Equation 24: I VGL VGL = Nx - AVDD + 2xV d + ------------------------------ ( f SW xC fly ) (EQ. 24) Where fSW is the switching frequency of the AVDD boost, Cfly is the flying capacitance (C22 in "Application/Block Diagram" on page 3). IVGL is the loading of VGL. 19 The boost overcurrent protection limits the boost MOSFET current on a cycle-by-cycle basis. When the MOSFET current reaches the current limit threshold, the current PWM switching cycle is terminated and the MOSFET is turned off for the remainder of that cycle. Overcurrent protection does not disable any of the regulators. Once the fault is removed (MOSFET current falls below current limit), the IC will continue with normal operation. UNDERVOLTAGE LOCKOUT (UVLO) If the input voltage (VIN) falls below the falling UVLO, all the channels will be disabled. All the rails will restart with normal soft-start operation when the VIN input voltage is applied again (VIN > rising UVLO). Refer to the "Electrical Specifications Table" on page 5 for the UVLO specifications. OVERVOLTAGE PROTECTION (OVP) The AVDD boost overvoltage protection monitors the AVDD voltage through AVDD pin. When the AVDD pin voltage exceeds the OVP level, the AVDD boost converter stops switching. No other channel faults out when AVDD OVP happens. The VGH boost overvoltage protection monitors the VGH voltage through the VGH pin. When the VGH pin voltage exceeds the OVP level, the VGH boost converter regulates the output voltage at 37.5V. No other channel faults out when VGH OVP happens. OVER-TEMPERATURE PROTECTION (OTP) The ISL98665 has a hysteretic over-temperature protection threshold set at +150C (typ). If this threshold is reached, all the channels are disabled immediately. When temperature falls by +40C (typ) then all the regulators automatically re-start. Power On/OFF Sequence When VIN rising exceeds rising UVLO and EN is high, VLOGIC starts up with a 0.45ms soft-start time. AVDD boost converter also starts up. The soft-start time of AVDD depends on the capacitance on the SS pin. The 2.5ms after AVDD soft-start is completed, the VGH boost converter starts up. The typical softstart time of VGH is 33ms. At power off, when VIN reaches falling UVLO, all channels shut down. The detailed power on/off sequence is shown in Figure 24. FN8564.0 June 27, 2013 ISL98665 Layout Recommendation The device's performance, including efficiency, output noise, transient response and control loop stability, is affected by the PCB layout. The PCB layout is critical, especially at high switching frequency. Following are some general guidelines for layout: 1. Place the external power components (the input capacitors, output capacitors, boost inductor and output diodes, etc.) in close proximity to the device. Traces to these components should be kept as short and thick as possible to minimize parasitic inductance and resistance. 2. The input bypass capacitor should be connected to the VIN pin with the smallest trace possible. 3. Loops with large AC amplitudes and fast slew rate should be made as small as possible. 4. The feedback network should sense the output voltage directly from the point of load. Minimize feedback track lengths to avoid switching noise pick-up. 5. Digital input pins and EN, should be isolated from the high di/dt and dv/dt signals. Otherwise, it may cause a glitch on those inputs. 7. Analog ground (AGND) and power ground (PGND) should be separated on PCB. The AGND is a quite ground plane with no large currents flowing through it for all the low-current sensitive analog and digital signals. The compensation and feedback components, soft start capacitors and bias input bypass capacitors need to be connected to AGND. AGND should be on a clearer layer and kept away from the noise. The PGND plane carries high currents, all the power components should be connected to PGND. AGND and PGND should be connected to each other on the PCB at a single point. It is crucial to connect these two grounds at the location very close to the IC. 8. The power ground (PGND) should be connected at the ISL98665 exposed die plate area. 9. To minimize the thermal resistance of the package when soldered to a multi-layer PCB, the amount of copper track and ground plane area connected to the exposed die plate should be maximized and spread out as far as possible from the IC. The bottom and top PCB areas especially should be maximized to allow thermal dissipation to the surrounding air. A demo board is available to illustrate the proper layout implementation. 6. I2C signals, if not used, should be tied to VIN. 20 FN8564.0 June 27, 2013 ISL98665 Power-ON/OFF Sequence UVLO UVLO EN = H VIN VSS=VIN EN VSS = VIN VSS = 1V, AVDD soft-start finish Pull to GND Charging VSS cap with 4A VSS VLOGIC VLOGIC soft-start = 0.45ms AVDD AVDD soft-start VGL 2.5ms VGH VGH soft-start = 33ms FIGURE 24. POWER-ON/OFF SEQUENCE 21 FN8564.0 June 27, 2013 ISL98665 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION June 27, 2013 FN8564.0 CHANGE Initial Release About Intersil Intersil Corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management semiconductors. The company's products address some of the largest markets within the industrial and infrastructure, personal computing and high-end consumer markets. For more information about Intersil, visit our website at www.intersil.com. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at www.intersil.com. You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/en/support/ask-an-expert.html. Reliability reports are also available from our website at http://www.intersil.com/en/support/qualandreliability.html#reliability For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 22 FN8564.0 June 27, 2013 ISL98665 Package Outline Drawing L28.4x5C 28 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE Rev 0, 9/08 2.50 4.00 B 22 5.00 PIN #1 INDEX AREA 28 23 6 PIN 1 INDEX AREA (4X) 6 24X 0.50 A 1 3.50 Exp. DAP 3.50 0.10 M C A B 4 28X 0.25 0.15 8 15 9 14 2.50 Exp. DAP SIDE VIEW TOP VIEW 28X 0.400 BOTTOM VIEW SEE DETAIL "X" ( 3.80 ) 0.10 C Max 0.80 ( 2.50) C SEATING PLANE 0.08 C SIDE VIEW ( 4.80 ) ( 24X 0.50) ( 3.50 ) C 0 . 2 REF 5 0 . 00 MIN. 0 . 05 MAX. (28X .250) DETAIL "X" ( 28 X 0.60) TYPICAL RECOMMENDED LAND PATTERN NOTES: 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension applies to the metallized terminal and is measured between 0.15mm and 0.30mm from the terminal tip. 5. Tiebar shown (if present) is a non-functional feature. 6. The configuration of the pin #1 identifier is optional, but must be located within the zone indicated. The pin #1 identifier may be either a mold or mark feature. 23 FN8564.0 June 27, 2013