6EP1332-2BA20 - SIEMENS - Datasheet.Live

SITOP PSU100S

___________________

SITOP power supply

SITOP PSU100S

Operating Instructions

SITOP PSU100S 24 V/2.5 A

6EP1332

-2BA20

SITOP PSU100S 24 V/5 A

6EP1333

-2BA20

SITOP PSU100S 24 V/10 A

6EP1334

-2BA20

SITOP PSU100S 24 V/20 A

EP1336-2BA10

SITOP

PSU100S 12 V/7 A

6EP1322

-2BA00

SITOP PSU100S 12 V/14 A

6EP1323

-2BA00

07.2014

C98130

-A7589-A1-5-7629

Overview

Safety instructions

Description, device design,

dimension drawing

Mounting/removal

Mounting position, mounting

clearances

Installation

Technical data

Safety, approvals, EMC

Ambient conditions

Applications

Environment

Service & Support

Siemens AG

Industry Sector

Postfach

48 48

90026 NÜRNBERG

GERMANY

C98130-A7589-A1-5-7629

Ⓟ

08/2014 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 3

Overview

Description

The 1-phase SITOP PSU100S from the SITOP smart product line is a powerful, regulated

standard power supply for automated machines and systems. In addition to a high efficiency,

these low-profile power supply units have an outstanding overload behavior.

The key benefits of the product include:

● Wide-range input, which allows them to be connected to almost any 1-phase line supply

around the world

● Output voltage can be adjusted in the range 22.2 (24)...28 V or 11.5…15.5 V

● Brief overload capability of 150% for 5 s/min (extra power)

● Continuous overload capability of 120% up to an ambient temperature of +45° C

● Integrated signaling contact for "24 V OK" or "12 V OK"

● Ambient temperature -25 (0)...+70 °C

● To increase the system availability, these reliable power supplies can be expanded using

SITOP supplementary modules (redundancy module, selectivity module, buffer module),

as well as SITOP DC-UPS modules.

Overview

SITOP PSU100S

4 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Ordering data

The following device options are available:

Regulated SITOP PSU100S power supply

Type

Order number

1-phase 120/230 V AC input,

24 V/2.5 A DC output

6EP1332-2BA20

1-phase 120/230 V AC input,

24 V/5 A DC output

6EP1333-2BA20

1-phase 120/230 V AC input,

24 V/10 A DC output

6EP1334-2BA20

1-phase 120/230 V AC input,

24 V/20 A DC output

6EP1336-2BA10

1-phase 120/230 V AC input,

12 V/7 A DC output

6EP1322-2BA00

1-phase 120/230 V AC input,

12 V/14 A DC output

6EP1323-2BA00

Accessories

Item

Order number

Device identification labels 10 mm × 7 mm, pastel turquoise

3RT1900-1SB10

Device identification labels 20 mm × 7 mm, pastel turquoise

3RT1900-1SB20

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 5

Table of contents

Overview................................................................................................................................................. 3

1 Safety instructions ................................................................................................................................... 7

2 Description, device design, dimension drawing........................................................................................ 9

2.1 Device description .......................................................................................................................... 9

2.2 Connections and terminal designation ......................................................................................... 10

2.3 Potentiometer ............................................................................................................................... 11

2.4 Status displays and signaling ....................................................................................................... 12

2.5 Block diagram .............................................................................................................................. 13

2.6 Dimensions and weight ................................................................................................................ 14

3 Mounting/removal ................................................................................................................................. 17

4 Mounting position, mounting clearances ................................................................................................ 19

4.1 Standard mounting position ......................................................................................................... 19

4.2 Other mounting positions ............................................................................................................. 22

4.2.1 6EP1332-2BA20 .......................................................................................................................... 22

4.2.2 6EP1333-2BA20 .......................................................................................................................... 24

4.2.3 6EP1334-2BA20 .......................................................................................................................... 26

4.2.4 6EP1336-2BA10 .......................................................................................................................... 28

4.2.5 6EP1322-2BA00 .......................................................................................................................... 30

4.2.6 6EP1323-2BA00 .......................................................................................................................... 32

5 Installation ............................................................................................................................................ 35

5.1 Line-side connection .................................................................................................................... 35

5.2 Output-side connection ................................................................................................................ 37

6 Technical data ...................................................................................................................................... 39

6.1 Input ............................................................................................................................................. 39

6.2 Output .......................................................................................................................................... 41

6.3 Efficiency ...................................................................................................................................... 47

6.4 Closed-loop control ...................................................................................................................... 50

6.5 Protection and monitoring ............................................................................................................ 51

6.6 MTBF ........................................................................................................................................... 51

6.7 Mechanical system ...................................................................................................................... 52

6.8 Accessories .................................................................................................................................. 53

6.9 Dimension drawing ...................................................................................................................... 53

Table of contents

SITOP PSU100S

6 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

7 Safety, approvals, EMC ........................................................................................................................ 55

7.1 Safety .......................................................................................................................................... 55

7.2 Test voltage ................................................................................................................................. 56

7.3 Approvals .................................................................................................................................... 57

7.4 EMC ............................................................................................................................................ 58

8 Ambient conditions ................................................................................................................................ 59

9 Applications .......................................................................................................................................... 61

9.1 Parallel connection to increase power rating .............................................................................. 61

9.2 Parallel connection for redundancy ............................................................................................. 63

9.3 Series connection for increased voltage ..................................................................................... 64

9.4 Overload protection in the 24 V output circuit ............................................................................. 65

9.5 Protection against short-time voltage dips .................................................................................. 66

9.6 Protecting against longer power failures ..................................................................................... 67

10 Environment ......................................................................................................................................... 69

11 Service & Support ................................................................................................................................. 71

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 7

Safety instructions

WARNING

Correct handling of the devices

When operating electrical devices, it is inevitable that certain components will carry

dangerous voltages.

Therefore, failure to handle the units properly can result in death or serious physical injury

as well as extensive property damage.

Only appropriately qualified personnel may work on or in the vicinity of this equipment.

Perfect, safe, and reliable operation of this equipment is dependent on proper

transportation, storage, installation and mounting.

Before installation or maintenance work can begin, the system's main switch must be

switched off and measures taken to prevent it being switched on again.

If this instruction is not observed, touching live parts can result in death or serious injury.

Safety instructions

SITOP PSU100S

8 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 9

Description, device design, dimension drawing

2.1

Device description

SITOP PSU100S is a primary-clocked power supply for connection to a 1-phase AC line

supply. An electronically regulated DC voltage that can be set via a potentiometer is

available at the output of the device. The output of the device is isolated, no-load proof and

short-circuit proof. The LED display indicates the operating status. The operating state of the

device can be processed via the signaling contact.

①

Line input

②

DC output

③

Signaling contacts

④

Potentiometer 22.2…28 / 24...28 V / 11.5…15.5 V

⑤

Indicator light (output voltage OK)

⑥

DIN rail slider

⑦

Natural convection

⑧

Clearance above/below

Figure 2-1 Design

Description, device design, dimension drawing

2.2 Connections and terminal designation

SITOP PSU100S

10 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

2.2

Connections and terminal designation

The line input terminals ① can be used to establish the connection to supply voltage. The

output terminals ② are used to connect to the loads to be supplied (see also Section

Installation (Page 35)).

The operating state of the device can be processed via the signaling contact ③ (function

and contact rating, see Chapter Status displays and signaling (Page 12)).

Connections and terminal designations

①

Line input L1, N, PE One screw terminal each

②

Output + 2 screw terminals

②

Output – 2 screw terminals

③

Signaling contact 13, 14 One screw terminal each

*1)

Do not subject the end stop to higher loads

Figure 2-2 Terminal data for 6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20, 6EP1322-

2BA00, 6EP1323-2BA00

*1)

Do not subject the end stop to higher loads

Figure 2-3 Terminal data for 6EP1336-2BA10

Description, device design, dimension drawing

2.3 Potentiometer

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 11

2.3

Potentiometer

The potentiometer ④ on the front of the device is used to adjust the output voltage. The

output voltage is set to the rated value at the factory and can be set within certain limits; for

example, to compensate voltage drops across long supply lines to the connected load.

Figure 2-4 Potentiometer

Type

Factory setting

Adjustment range

6EP1322-2BA00

6EP1323-2BA00

12 V 11.5...15.5 V

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

24 V 22.2...28 V

6EP1336-2BA10 24 V 24...28 V

NOTICE

Thermal overload possible

When adjusting the output voltage to greater than the rated voltage, the output current must

be derated by 4 %/V, or the permissible ambient temperature must be taken into account

with 3° C/V.

Note

It is only permissible t

o use an insulated screwdriver when actuating the potentiometer.

For notes on actuating the potentiometer (screwdriver, torque), refer to Figure 2-2 Terminal

data for 6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20, 6EP1322-2BA00, 6EP1323-

2BA00 (Page 10) and Figure 2-3 Terminal data for 6EP1336-2BA10 (Page 10).

Description, device design, dimension drawing

2.4 Status displays and signaling

SITOP PSU100S

12 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

2.4

Status displays and signaling

6EP1322-2BA00, 6EP1323-2BA00, 6EP1332-2BA20

6EP1333-2BA20, 6EP1334-2BA20, 6EP1336-2BA10

Status display

LED green for 24 V O.K. or 12 V O.K.

Signaling contact Relay contact (NO contact, contact rating 30 V AC / 0.5 A, 60 V DC / 0.3 A, 30 V DC / 1 A)

for 24 V O.K. or 12 V O.K.

Figure 2-5 Status displays and signaling

Signaling

6EP1322-2BA00

6EP1323-2BA00

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

LED ⑤ lights up green

Signaling contact ③,

contacts 13-14 closed

Normal operation,

Output voltage

>10 V ±0.5 V

Normal operation,

Output voltage

>20 V ±0.5 V

Normal operation,

Output voltage

>20 V ±0.5 V

LED ⑤ dark

Signaling contact ③,

contacts 13-14 open

(inactive position)

Overload operation or power

supply voltage missing

Overload operation or power

supply voltage missing

Overload / hiccup operation,

power supply missing or the

device has tripped due to

overtemperature (reset

possible with power OFF for

approx. 30 min)

Description, device design, dimension drawing

2.5 Block diagram

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 13

2.5

Block diagram

Figure 2-6 Block diagram

Description, device design, dimension drawing

2.6 Dimensions and weight

SITOP PSU100S

14 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

2.6

Dimensions and weight

Figure 2-7 Dimension drawing 6EP1332-2BA20

Figure 2-8 Dimension drawing 6EP1333-2BA20, 6EP1322-2BA00

Description, device design, dimension drawing

2.6 Dimensions and weight

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 15

Figure 2-9 Dimension drawing 6EP1334-2BA20, 6EP1323-2BA00

Figure 2-10 Dimension drawing 6EP1336-2BA10

6EP1332-2BA20

6EP1333-2BA20

6EP1322-2BA00

6EP1334-2BA20

6EP1323-2BA00

6EP1336-2BA10

Dimensions

(W × H × D) in mm

32.5 × 125 × 120 50 × 125 × 120 70 × 125 × 120 115 × 145 × 150

Weight

Approx. 0.3 kg

Approx. 0.4 kg

Approx. 0.7 kg

Approx. 2.4 kg

Description, device design, dimension drawing

2.6 Dimensions and weight

SITOP PSU100S

16 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 17

Mounting/removal

WARNING

Installing the device in a housing or a control cabinet

SITOP PSU100S power supplies are built-in units. They must be installed in a housing or

control cabinet where only qualified personnel have access.

The device can be mounted in a control cabinet on standard mounting rails according to

EN 60715.

Mounting

To mount the device, position it with the mounting rail guide at the upper edge of the

standard mounting rail and press down to lock it into place. If this is too difficult, press slider

⑥ at the same time, as described under "Removal".

Removal

To remove, pull up the slider ⑥ using a screwdriver and disengage the device at the bottom

edge of the standard mounting rail (see Removal diagram (Page 17)). Then you can remove

the device from the upper edge of the standard mounting rail.

Figure 3-1 Removal

WARNING

Use in hazardous zones

If the device is to be used in a hazardous zone (Ex II 3G Ex nA nC IIC T4 Gc) it must be

installed in a distributor box with degree of protection IP54 or higher.

Mounting/removal

SITOP PSU100S

18 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 19

Mounting position, mounting clearances

4.1

Standard mounting position

The device is designed for installation on standard EN 60715 35×7.5/15 mounting rails. The

device must be mounted vertically to ensure proper cooling, and with the input terminals and

output terminals at the bottom.

A clearance of at least 50 mm should be maintained above and below the device (maximum

depth of the cable duct, 50 mm).

No space is required at the side.

Output current as a function of the ambient temperature and mounting height

Figure 4-1 6EP1332-2BA20: Output current in the standard mounting position

Figure 4-2 6EP1333-2BA20: Output current in the standard mounting position

Mounting position, mounting clearances

4.1 Standard mounting position

SITOP PSU100S

20 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Figure 4-3 6EP1334-2BA20: Output current in the standard mounting position

Figure 4-4 6EP1336-2BA10: Output current in the standard mounting position

Figure 4-5 6EP1322-2BA00: Output current in the standard mounting position

Mounting position, mounting clearances

4.1 Standard mounting position

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 21

Figure 4-6 6EP1323-2BA00: Output current in the standard mounting position

Figure 4-7 Mounting height derating

Details see chapter Ambient conditions (Page 59)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

22 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2

Other mounting positions

For mounting positions that deviate from the standard mounting position, derating factors

(reduction of the output power or the permissible ambient temperature) must be observed in

accordance with the following diagrams.

Note

In the case of mounting positions

that deviate from the standard mounting position, reduced

mechanical resistance of the devices against vibration and shock must be expected.

Particularly when installing on a vertically fastened standard mounting rail, additional

measures may be required,

e.g. to prevent the device from slipping on the standard

mounting rail.

4.2.1

6EP1332-2BA20

Figure 4-8 Mounting position (1)

Figure 4-9 Mounting position (2)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 23

Figure 4-10 Mounting position (3)

Figure 4-11 Mounting position (4)

Figure 4-12 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

24 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2.2

6EP1333-2BA20

Figure 4-13 Mounting position (1)

Figure 4-14 Mounting position (2)

Figure 4-15 Mounting position (3)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 25

Figure 4-16 Mounting position (4)

Figure 4-17 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

26 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2.3

6EP1334-2BA20

Figure 4-18 Mounting position (1)

Figure 4-19 Mounting position (2)

Figure 4-20 Mounting position (3)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 27

Figure 4-21 Mounting position (4)

Figure 4-22 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

28 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2.4

6EP1336-2BA10

Figure 4-23 Mounting position (1)

Figure 4-24 Mounting position (2)

Figure 4-25 Mounting position (3)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 29

Figure 4-26 Mounting position (4)

Figure 4-27 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

30 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2.5

6EP1322-2BA00

Figure 4-28 Mounting position (1)

Figure 4-29 Mounting position (2)

Figure 4-30 Mounting position (3)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 31

Figure 4-31 Mounting position (4)

Figure 4-32 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

32 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

4.2.6

6EP1323-2BA00

Figure 4-33 Mounting position (1)

Figure 4-34 Mounting position (2)

Figure 4-35 Mounting position (3)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 33

Figure 4-36 Mounting position (4)

Figure 4-37 Mounting position (5)

Mounting position, mounting clearances

4.2 Other mounting positions

SITOP PSU100S

34 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 35

Installation

WARNING

Hazard due to electric shock

Before installation or maintenance work can begin, the system's main switch must be

switched off and measures taken to prevent it being switched on again. If this instruction is

not observed, touching live parts can result in death or serious injury.

5.1

Line-side connection

The SITOP PSU100S power supply is designed for connection to a 1-phase AC line supply

(TN or TT system according to VDE 0100 T 300 / IEC 364-3) with a rated voltage of

120/230 V AC, 50/60 Hz.

Figure 5-1 Line connection (examples 6EP1334-2BA20 and 6EP1336-2BA10)

The line supply is connected using terminals L1, N and PE (see Figure 5-1 Line connection

(examples 6EP1334-2BA20 and 6EP1336-2BA10) (Page 35)), and must be implemented

according to IEC 60364 and EN 50178 . A protective device (miniature circuit-breaker or

circuit-breaker) and a disconnection unit for the power supply must be provided. A ground-

fault circuit interrupter is not permissible against indirect contact as the only protective

measure. This is true for the complete line supply protected by the ground-fault circuit

interrupter.

Installation

5.1 Line-side connection

SITOP PSU100S

36 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Protection

SITOP PSU100S

Recommended line-side protection

6EP1332-2BA20 Miniature circuit breaker (IEC 898) characteristic C, 3 A

6EP1333-2BA20

Miniature circuit breaker (IEC 898) characteristic C, 6 A

6EP1334-2BA20

Miniature circuit breaker (IEC 898) characteristic C, 10 A

6EP1336-2BA10 Miniature circuit breaker (IEC 898) characteristic C, 10 A

circuit breaker 3RV2411-1JA10 (120 V)

3RV2411-1FA10 (230 V)

6EP1322-2BA00

Miniature circuit breaker (IEC 898) characteristic C, 6 A

6EP1323-2BA00

Miniature circuit breaker (IEC 898) characteristic C, 10 A

The protective conductor of the line supply must be connected at the PE terminal.

Other country-specific regulations may have to be observed when installing the device.

Installation

5.2 Output-side connection

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 37

5.2

Output-side connection

At its output, the SITOP PSU100S power supply provides an isolated (= non-grounded)

SELV output voltage (Safety Extra Low Voltage). The output of the power supply is no-load,

overload, and short-circuit proof. If an overload occurs, the electronic current limitation limits

the output current to a maximum value (refer to chapter Technical data (Page 39)).

Figure 5-2 Connecting the output voltage (examples 6EP1334-2BA20 and 6EP1336-2BA10)

The output voltage is connected via the + and - terminals at the output of the power supply

(see Figure 5-2 Connecting the output voltage (examples 6EP1334-2BA20 and 6EP1336-

2BA10) (Page 37)). Ensure that the output cables are dimensioned correctly for the

maximum output current rms value and fused accordingly.

Note

If the safety concept of the plant or system specifies that the DC output circuit should be

grounded (PELV), then it is permissible that the output voltage of the SITO

P power supply is

grounded. In this case, ideally, the grounding at the output should be directly connected from

terminal "

-" of the power supply to a suitable connection point of the protective conductor

system (PE) of the plant or system.

Installation

5.2 Output-side connection

SITOP PSU100S

38 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 39

Technical data

Note

Technical data is applicable for a rated input voltage, rated load and +25° C ambient

temperature (if nothing else is specified).

6.1

Input

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Input

1-phase, AC

Rated voltage

Ue rated

120 / 230 V

Voltage range

85-132 / 170-264 V

85-132 / 176-264 V

automatic range

switchover

Yes

Connect/shutdown

threshold, typical

80 V / 61 V 77 V / 63 V 70 V / 66 V 80 V/78 V or

160 V/155 V

Power failure buffering

at Ia rated, min

20 ms 20 ms 20 ms 20 ms

Power-failure buffering

at 93 / 187 V

at 120 / 230 V

Rated line frequency

50/60 Hz

Line frequency range

47...63 Hz

Input current / at rated

value of input voltage

120 V

1.25 A 2.34 A 4.49 A 7.5 A

Input current / at rated

value of input voltage

230 V

0.74 A 1.36 A 1.91 A 3.5 A

Switch-on current

limitation (+25 °C),

max.

33 A 40 A 60 A 11 A

I²t, at 120 V AC, max

0.1 A

0.3 A

1.6 A

2.5 A

I²t, at 230 V AC, max.

0.4 A

1.0 A

5.6 A

10 A

Integrated input fuse

Fuse T 3.15 A

Fuse T 6 A

Fuse T 10 A

Technical data

6.1 Input

SITOP PSU100S

40 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Protection in the line

feeder cable (IEC 898)

Recommended: Circuit

breaker, C

characteristic, 3 A

Recommended: Circuit

breaker, C

characteristic, 6 A

Recommended: Circuit

breaker, C

characteristic, 10 A

Recommended: Circuit

breaker, C

characteristic, 10 A

Circuit breaker

3RV2411-1JA10

(120 V) or 3RV2411-

1FA10 (230 V)

Overvoltage strength

2.3 × Ue rated, 1.3 ms

6EP1322-2BA00

6EP1323-2BA00

Input

1-phase, AC

Rated voltage Ue rated

120 / 230 V

Voltage range

85-132 / 170-264 V

automatic range switchover

Yes

Connect/shutdown threshold,

typical

82 V / 66 V 66 V / 63 V

Power failure buffering at

Ia rated, min

20 ms 20 ms

Power-failure buffering

at 93 / 187 V

Rated line frequency 50/60 Hz

Line frequency range 47...63 Hz

Input current / at rated value of

input voltage 120 V

1.73 A 3.24 A

Input current / at rated value of

input voltage 230 V

0.99 A 1.41 A

Switch-on current limitation

(+25 °C), max.

45 A 60 A

I²t, at 120 V AC, max.

0.3 A

1.6 A

I²t, at 230 V AC, max.

1.0 A

5.6 A

Integrated input fuse

Fuse T 3.15 A

Fuse T 6 A

Protection in the line feeder

cable (IEC 898)

Recommended: Circuit breaker,

C characteristic, 3 A

Recommended: Circuit breaker,

C characteristic, 6 A

Overvoltage strength

2.3 × Ue rated, 1.3 ms

Technical data

6.2 Output

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 41

Figure 6-1 Power-failure buffering

6.2

Output

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Output

Regulated, isolated DC voltage

Rated voltage value

Ua rated DC

24 V

Total tolerance, static ±

3 %

Static line regulation,

approx. ±

0,1 % 0,1 % 0,1 % 0,5 %

Static load regulation,

approx. ±

1 % 1 % 1 % 1 %

Residual ripple

Peak-peak, max.

150 mV 150 mV 150 mV 150 mV in the load

range >100 mA

300 mV in the load

range up to 100 mA

Spikes peak-peak, max.

(bandwidth, 200 MHz)

240 mV 240 mV 240 mV 240 mV

Adjustment range

22.8...28.0 V

24...28.0 V

Product function / output

voltage can be adjusted

Yes

Output voltage setting

• Remark

Using a potentiometer

Max. 480 W

Status display

LED green for 24 V O.K.

Signaling

Relay contact (NO contact, rating 60 V DC /0.3 A) for 24 V O.K.

Response when

switching on/off

Overshoot of Ua<720 mV No overshoot of Ua

(soft start), with the

exception of a

capacitive load

Starting delay, max.

300 ms

1.5 s

Technical data

6.2 Output

SITOP PSU100S

42 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Start delay, typ.

200 ms

160 ms

150 ms

500 ms

Voltage rise

120 V / 230 V AC max.

100 ms 100 ms 100 ms 500 ms

Voltage rise

120 V / 230 V AC typ.

15 ms 15 ms 20 ms 50 ms

Rated current Ia rated

2.5 A

5 A

10 A

20 A

Current range

• Remark

0...2.5 A

3 A to +45° C

+60 to +70 °C;

derating:

3 % Ia rated/K

0...5 A

6 A to +45° C

+60 to +70 °C;

derating:

3 % Ia rated/K

0...10 A

12 A to +45° C

+60 to +70 °C;

derating:

3 % Ia rated/K

0...20 A

24 A to +45° C

+60 to +70 °C;

derating:

5 % Ia rated/K

Output active power /

typical

60 W 120 W 240 W 480 W

Overload capability

(Extra Power)

3.75 A for 5 s/min 7.5 A for 5 s/min 15 A for 5 s/min 30 A for 5 s/min

Short-time overload

current / for a short

circuit when powering up

/ typical

9 A 18 A 33 A 35 A

Duration of the overload

capability, overcurrent /

for a short circuit while

powering up

• Remark

800 ms

once-only

800 ms

once-only

800 ms

once-only

100 ms

every 2.5 s

Short-time overload

current / for a short

circuit in operation /

typical

9 A 18 A 33 A 35 A

Duration of the overload

capability, overcurrent /

for a short circuit in

operation

• Remark

800 ms

once-only

800 ms

once-only

800 ms

once-only

100 ms

every 2.5 s

Can be connected in

parallel to increase the

power rating

Yes

Number of devices that

can be connected in

parallel to increase the

power rating, units

Output characteristic see diagram, output

characteristic for

6EP1332-2BA20

(Page 44)

see diagram, output

characteristic for

6EP1333-2BA20

(Page 45)

see diagram, output

characteristic for

6EP1334-2BA20

(Page 45)

see diagram, output

characteristic for

6EP1336-2BA20

(Page 45)

Capacitive load, max.

2 mF/A

Technical data

6.2 Output

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 43

6EP1322-2BA00

6EP1323-2BA00

Output Regulated, isolated DC voltage

Rated voltage value Ua rated

12 V

Total tolerance, static ±

3 %

Static line regulation, approx. ±

0,1 %

Static load regulation, approx. ±

1 %

Residual ripple

Peak-peak, max.

150 mV 150 mV

Spikes peak-peak, max.

(bandwidth, 200 MHz)

240 mV 240 mV

Adjustment range

11.5...15.5 V

Product function / output voltage

can be adjusted

Yes

Output voltage setting

Using a potentiometer

Status display

LED green for 12 V O.K.

Signaling

Relay contact (NO contact, rating 60 V DC /0.3 A) for 12 V O.K.

Response when switching on/off

Overshoot of Ua<360 mV

Starting delay, max.

300 ms

Start delay, typ.

180 ms

170 ms

Voltage rise

120 V / 230 V AC max.

100 ms 100 ms

Voltage rise

120 V / 230 V AC typ.

10 ms 10 ms

Rated current Ia rated

7 A

14 A

Current range

• Remark

0...7 A

+55...+70 °C derating:

5 % Ia rated/K

0...14 A

+55...+70 °C derating:

5 % Ia rated/K

Output active power / typical

84 W

168 W

Overload capability (Extra

Power)

10.5 A for 5 s/min 21 A for 5 s/min

Short-time overload current / for

a short circuit when powering up

/ typical

26 A 48 A

Duration of the overload

capability, overcurrent / for a

short circuit while powering up

• Remark

800 ms

once-only

800 ms

once-only

Short-time overload current / for

a short circuit in operation /

typical

26 A 48 A

Technical data

6.2 Output

SITOP PSU100S

44 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

6EP1322-2BA00

6EP1323-2BA00

Duration of the overload

capability, overcurrent / for a

short circuit in operation

• Remark

800 ms

once-only

800 ms

once-only

Can be connected in parallel to

increase the power rating

Yes

Number of devices that can be

connected in parallel to increase

the power rating, units

Output characteristic see diagram, output

characteristic for 6EP1322-

2BA20 (Page 46)

see diagram, output

characteristic for 6EP1323-

2BA20 (Page 46)

Capacitive load, max.

2 mF/A

Figure 6-2 Startup delay/voltage rise

Figure 6-3 Output characteristic 6EP1332-2BA20

Technical data

6.2 Output

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 45

Figure 6-4 Output characteristic 6EP1333-2BA20

Figure 6-5 Output characteristic 6EP1334-2BA20

Figure 6-6 Output characteristic 6EP1336-2BA10

Technical data

6.2 Output

SITOP PSU100S

46 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Figure 6-7 Output characteristic 6EP1322-2BA00

Figure 6-8 Output characteristic 6EP1323-2BA00

The device supplies a constant output voltage until the current limit is reached. In the event

of an overload, the output current and the output voltage are reduced.

When the output voltage falls below approx. 10 V, the 6EP1336-2BA10 device switches off,

and automatically restarts. This response is repeated as long as the overload condition is

present.

Technical data

6.3 Efficiency

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 47

6.3

Efficiency

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Efficiency at Ua rated, Ia rated

120 V / 230 V AC approx.

83 % / 85 % 86 % / 87 % 89 % / 90 % 89 % / 90 %

Power loss at Ua rated, Ia rated

120 V / 230 V AC approx.

11 W / 10 W 18 W / 16 W 27 W / 25 W 59 W / 53 W

Power loss when idling

120 V / 230 V AC approx.

1.7 W / 1.2 W 1.8 W / 1.3 W 3.0 W / 2.4 W 4.1 W / 3.6 W

6EP1322-2BA00

6EP1323-2BA00

Efficiency at Ua rated, Ia rated

120 V / 230 V AC approx.

82 % / 83 % 86 % / 87 %

Power loss at Ua rated, Ia rated

120 V / 230 V AC approx.

16 W / 15 W 27 W / 15 W

Power loss when idling

120 V / 230 V AC approx.

1.5 W / 1.0 W 2.8 W / 2.3 W

Figure 6-9 Efficiency 6EP1332-2BA20

Technical data

6.3 Efficiency

SITOP PSU100S

48 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Figure 6-10 Efficiency 6EP1333-2BA20

Figure 6-11 Efficiency 6EP1334-2BA20

Technical data

6.3 Efficiency

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 49

Figure 6-12 Efficiency 6EP1336-2BA10

Figure 6-13 Efficiency 6EP1322-2BA00

Technical data

6.4 Closed-loop control

SITOP PSU100S

50 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Figure 6-14 Efficiency 6EP1323-2BA00

6.4

Closed-loop control

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

6EP1322-2BA00

6EP1323-2BA00

Dyn. line regulation

(Ue rated ±15%), max.

0.3 % Ua 0.3 % Ua 0.3 % Ua

Dyn. load regulation

(Ia: 10/90/10 %), max.

±5 % Ua - ±15 % UA

Dyn. load regulation

(Ia: 10/90/10 %), typ.

- ±3 % Ua -

Load-step settling time

10 to 90 %, max.

1 ms 10 ms 1 ms

Load-step settling time

10 to 90 %, typ.

- 2 ms -

Load-step settling time

90 to 10 %, max.

1 ms 10 ms 1 ms

Load-step settling time

90 to 10 %, typ.

- 2 ms -

Technical data

6.5 Protection and monitoring

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 51

6.5

Protection and monitoring

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

Output overvoltage

protection

in the case of an internal fault Ua < 33 V Yes, according to

EN 60950-1

Current limitation

Typ.

• Remark

3.75 A

Overload capability

with 150 % Ia rated up

to 5 s/min

7.5 A

Overload capability

with 150 % Ia rated up

to 5 s/min

15 A

Overload capability

with 150 % Ia rated up

to 5 s/min

21.5 A (>45 °C)

25.5 A (<45 °C)

Overload capability

with 150 % Ia rated up

to 5 s/min

Short-circuit protection Yes, current is statically limited Electronic trip,

automatic restart

(hiccup)

Continuous short-

circuit current rms

value, approx.

3.4 A 7.3 A 14.6 A 7 A

Overload / short-circuit

display

6EP1322-2BA00

6EP1323-2BA00

Output overvoltage protection

< 20 V

Current limitation, typ.

• Remark

10.5 A

Overload capability with

150 % Ia rated up to 5 s/min

21 A

Overload capability with

150 % Ia rated up to 5 s/min

Short-circuit protection Yes, current is statically limited

Continuous short-circuit current

rms value, approx.

8.8 A 16.4 A

Overload / short-circuit display

6.6

MTBF

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1322-2BA00

6EP1323-2BA00

6EP1336-2BA10

Mean Time Between Failures SN29500:

> 1600000 h

at 40 °C, rated load, 24 h operation

SN29500:

> 500000 h (typ. 700000 h)

at 40° C, rated load, 24 h operation

Technical data

6.7 Mechanical system

SITOP PSU100S

52 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

6.7

Mechanical system

6EP1332-2BA20

6EP1333-2BA20

6EP1322-2BA00

6EP1334-2BA20

6EP1323-2BA00

6EP1336-2BA10

Connection system

Screw-type terminal

Connections / line

supply

L, N, PE: 1 screw terminal each for 0.5 ... 2.5 mm² solid/finely stranded L1, N, PE: 1 screw

terminal each for

0.2 ... 4 mm²

solid/finely stranded

Connections / output +, -: 2 screw terminals each for 0.5 ... 2.5 mm² +, -: 2 screw terminals

each for 0.2 ... 4 mm²

Connections / auxiliary

contacts

Signaling contact: 2 screw terminals for 0.5 mm ... 2.5 mm² 13, 14 (signaling

contact): 1 screw

terminal each for

0.14 ... 1.5 mm²

Width of the housing

32.5 mm

50 mm

70 mm

115 mm

Height of the housing

125 mm

145 mm

Depth of the housing

120 mm

150 mm

Installation width

32.5 mm

50 mm

70 mm

120 mm

Mounting height

225 mm

245 mm

Weight, approx.

0.32 kg

0.5 kg

0.8 kg

2.4 kg

Product feature of the

housing / housing that

can be lined up next to

one another

Yes

Type of mounting /

panel mounting

Type of mounting / rail

mounting

Yes

Type of mounting /

S7-300 rail mounting

Mounting

Can be snapped onto standard EN 60715 35x7,5/15 mounting rails

Technical data

6.8 Accessories

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 53

6.8

Accessories

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

6EP1322-2BA00

6EP1323-2BA00

Electrical accessories

Redundancy module, buffer module

Mechanical accessories Device identification labels

10 mm × 7 mm, pastel turquoise

3RT1900-1SB10

Device identification labels

20 mm × 7 mm, pastel turquoise

3RT1900-1SB20

6.9

Dimension drawing

See chapter Dimensions and weight (Page 14)

CAD data that can be downloaded from the Internet:

6EP1332-2BA20

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00727)

6EP1333-2BA20

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00730)

6EP1334-2BA20

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00733)

6EP1336-2BA10

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00720)

6EP1322-2BA00

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00736)

6EP1323-2BA00

(http://www.automation.siemens.com/bilddb/index.aspx?objKey=G_KT01_XX_00739)

Technical data

6.9 Dimension drawing

SITOP PSU100S

54 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 55

Safety, approvals, EMC

7.1

Safety

6EP1332-2BA20, 6EP1333-2BA20, 6EP1334-2BA20,

6EP1336-2BA10, 6EP1322-2BA00, 6EP1323-2BA00

Primary/secondary galvanic isolation

Yes

Galvanic isolation SELV output voltage Ua according to EN 60950-1 and EN 50178

Transformer according to EN 61558-2-16

Protection class

Class I

Degree of protection (EN 60529)

IP20

Leakage current, typ.

1 mA

Leakage current, max.

3.5 mA

Test voltage

See Table 7-1 Test voltage (Page 56)

Safety, approvals, EMC

7.2 Test voltage

SITOP PSU100S

56 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

7.2

Test voltage

Figure 7-1 Test voltage diagram

Only the manufacturer can perform the type test and production test; users can also perform

the field test.

Preconditions for performing the field test:

Tests (A) & (B)

● Connect the input terminals with one another (L, N)

● Connect the output terminals, signaling contact and PE with one another

Test (C)

● Connect the output terminals and signaling contact with one another and measure with

respect to PE

Table 7- 1 Test voltage

Test time

Prim ↔ sec (A)

Prim ↔ PE (B)

Sec ↔ PE (C)

Type test

60 s

4200 VDC

2200 VDC

700 VDC

60 s

3000 VAC

1500 VAC

500 VAC

Production test

1 s

2200 VDC

500 VDC

1 s

1500 VAC

350 VAC

Field test

1 s

2200 VDC

500 VDC

1 s

1500 VAC

350 VAC

Remark:

Tripping current for DC measurement: 0

Tripping current for AC measurement: <100 mA

Safety, approvals, EMC

7.3 Approvals

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 57

7.3

Approvals

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1336-2BA10

6EP1322-2BA00

6EP1323-2BA00

CE marking Yes, (2004/108/EG and 2006/95/EG)

CSA approval

Yes, CSA C22.2 No. 60950-1, cCSAus (ANSI/ISA 12.12.01)

UL/cUL approval

cULus-listed (UL 508, CSA 22.2 No. 107.1), File E197259

Explosion protection ATEX EX II 3G Ex nA nC IIC T4 Gc;

cCSAus Class I, Div. 2, GROUPS A, B, C, D, T4

CB approval

Yes

CB-Scheme

IEC 60950-1

SEMI F47 compliance

Not tested

fulfilled

Not tested

Marine approvals Germanischer Lloyd (GL),

BV marine

Germanischer Lloyd (GL) Germanischer Lloyd (GL)

Safety, approvals, EMC

7.4 EMC

SITOP PSU100S

58 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

7.4

EMC

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1322-2BA00

6EP1323-2BA00

6EP1336-2BA10

Electrostatic

discharge

EN 61000-4-2 8 kV contact, 8 kV air 8 kV contact, 8 kV air

Electromagnetic

fields

EN 61000-4-3 80…1,000 MHz 10 V/m

1400…2,000 MHz 10 V/m

2000…2700 MHz 10 V/m

895…905 MHz and 1.89 GHz 10 V/m

80…1,000 MHz 15 V/m

1000…2700 MHz 10 V/m

High-speed transient

disturbance variables

(burst)

EN 61000-4-4 2 kV at line connections

1 kV at DC output

4 kV at line connections

2 kV at DC output

Surge voltages EN 61000-4-5 2 kV symmetrical at the line connections

4 kV asymmetrical at the line connections

500 V symmetrical/asymmetrical on DC output cables

High-frequency fields

EN 61000-4-6

10 V; 0.15…80 MHz

Magnetic fields

EN 61000-4-8

Not applicable

30 A/m; 50 Hz

Voltage dips EN 61000-4-11 100% for 20 ms,

60% for 200 ms,

30% for 500 ms

100% for 20 ms,

60% for 200 ms,

30% for 500 ms

Voltage interruptions

EN 61000-4-11

100% for 5000 ms

Emitted interference

EN 55022

Class B

Line harmonics

limitation

EN 61000-3-2 Class A Class A

Generic standards

EN 61000-6-2

Immunity for industrial environments

EN 61000-6-3

Emission for residential areas

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 59

Ambient conditions

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1322-2BA00

6EP1323-2BA00

6EP1336-2BA10

Ambient temperature -25 ... +70 °C with natural convection

(self convection)

Derating for 24 V versions:

from +60°C: 3 % Ia, rated/K;

from Ua>24 V: -10...+50 °C

from Ue<100 V and lower, output

power is reduced depending on the

ambient temperature

Derating for 12 V versions:

from +55 °C: 5 % Ia, rated/K

0 ... +70 °C with natural convection

(self convection)

Derating:

from +60°C: 5 % Ia, rated/K;

from Ue<100 V or Ue<200

V and lower,

output power is reduced depending on

the ambient temperature

Tested according to:

• EN 60068-2-1 cold

• EN 60068-2-2 dry heat

• EN 60068-2-78 humid heat, constant

• EN 60068-2-14 temperature change

Transport and storage temperature -40 ... +85° C

Tests (packed for shipping) according to:

• EN 60068-2-1 cold

• EN 60068-2-2 dry heat

• EN 60068-2-30 humid heat, cyclic

Humidity class

Climatic class 3K3 according to EN 60721, without condensation

Ambient conditions

SITOP PSU100S

60 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

6EP1332-2BA20

6EP1333-2BA20

6EP1334-2BA20

6EP1322-2BA00

6EP1323-2BA00

6EP1336-2BA10

Mechanical stressing in operation Tested according to:

• EN 60068-2-6 vibration, test Fc:

3.5 mm deflection in the range 5 – 8.4 Hz

2 g acceleration in the range 8.4 – 150 Hz

• EN 60068-2-27 shock, test Ea:

acceleration 150 m/s2 , test duration 11 ms

Damaging gases Tested according to:

• EN 60068-2-42 sulfur dioxide

• EN 60068-2-43 hydrogen sulfide

Atmospheric pressure Operation:

• 1080 ... 795 hPa (-1000 ... +2000 m)

• For operation at altitudes of 2000 m up to 6000 m above sea level:

output must be derated by -7.5 % / 1000 m or

the ambient temperature must be reduced by 5 K / 1000 m

see Figure 4-7 Mounting height derating (Page 21)

• Overvoltage category:

III to 2000 m (EN 50178)

II from 2000 m to 6000 m (EN 50178)

II to 2000 m (EN 60950-1)

I from 2000 m to 6000 m (EN 60950-1)

Storage:

• 1080 ... 660 hPa (-1000 ... +3500 m)

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 61

Applications

9.1

Parallel connection to increase power rating

To increase the power rating, two SITOP PSU100S power supplies of the same type can be

directly connected in parallel.

The following must be observed:

● The cables connected to each power supply at terminals "+" and "-" must have identical

lengths and the same cable cross-sections (or the same impedance) up to a common

external connection point (terminal strip) if possible.

● The power supplies connected in parallel must be switched on simultaneously with a

common switch in the line feeder cable (e.g. with the main switch available in control

cabinets).

● The output voltages measured in no-load operation for the power supplies that are not yet

connected in parallel should not deviate more than a maximum of 50 mV. This usually

corresponds to the factory setting. If the output voltage is changed, you should connect

the "-" terminals and then, in no-load operation, measure the voltage difference between

the "+" terminals that have not yet been connected. The voltage difference should not

exceed 50 mV.

Figure 9-1 Parallel connection

Note

It is not permissible to take into account simultaneous overload capability (Extra

Power 150%

for 5

s/min) of several power supplies connected in parallel when configuring the power

supply system.

Applications

9.1 Parallel connection to increase power rating

SITOP PSU100S

62 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

NOTICE

Protective circuit for the parallel connection of more than two power supplies

For connection of more than two power supplies in parallel, additional measures must be

taken to prevent high backward feeding currents in the event of a secondary device fault.

For this purpose, a suitable protective circuit (e.g. decoupling diode or DC-conform circuit-

breaker) must be installed between each "+" terminal of the power supply and the common

connection point.

Applications

9.2 Parallel connection for redundancy

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 63

9.2

Parallel connection for redundancy

Connecting several SITOP PSU100S power supplies in parallel for redundancy purposes is

required if especially high demands are placed regarding the availability of a reliable 24 V

power supply.

Using the SITOP PSE202U redundancy module, two 24 V power supplies of the same type

up to 20 A can be decoupled (Figure 9-2 Redundant configuration with two power supplies

and SITOP PSE202U redundancy module (Page 63)). When one of the devices fails, then

the other automatically takes over the power supply. If one of the power supplies fails, then

this is signaled using an LED on the redundancy module as well as an isolated relay contact.

When dimensioning the system, it must be ensured that n+1 redundant connected power

supplies can handle the total power requirement of the remaining n power supplies.

Note

For a high reliability of the supply, it is recommended that the redundant switched power

supplies are fused separately on the line

-side and, if possible, be connected to different

power supply networks.

Figure 9-2 Redundant configuration with two power supplies and SITOP PSE202U redundancy

module

You can find additional information at:

SITOP PSE202U manual (http://support.automation.siemens.com/WW/view/en/42248598)

Applications

9.3 Series connection for increased voltage

SITOP PSU100S

64 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

9.3

Series connection for increased voltage

To achieve an output voltage of 48 V DC, two 24 V SITOP PSU100S power supplies of the

same type can be connected in series. In this case, connect the "-" terminal of the first power

supply to the "+" terminal of the second power supply. The "+" terminal of the first power

supply and the "-" terminal of the second power supply are routed to the load.

Depending on the grounding point of the secondary output voltages, voltages of +48 V,

±24 V or -48 V can be realized.

In the case of an asymmetric load distribution, it is not possible to guarantee correct

functionality.

WARNING

SELV is not guaranteed in the case of a fault

When connecting two power supplies in series, the continuous, permissible SELV voltage

of a maximum of 60 VDC according to EN 60950-1 cannot be guaranteed in the case of a

fault.

Figure 9-3 Series connection

Applications

9.4 Overload protection in the 24 V output circuit

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 65

9.4

Overload protection in the 24 V output circuit

If overload occurs, the electronic current limiting of the SITOP PSU100S power supply limits

the output current to a maximum value (refer to chapter Technical data (Page 39)). The

output cables are protected against a thermal overload if they are dimensioned

corresponding to the maximum rms output current, or protected using additional components

(for example, miniature circuit breaker, fuses).

However, a load circuit that fails as a result of overload, for instance, should frequently be

reliably and quickly identified and specifically switched off before the power supply goes into

current-limiting mode (in current-limiting mode, the supply voltage would also be reduced for

all of the remaining 24 V loads).

The SITOP PSE200U selectivity module with 4 channels (versions with adjustable output

current range for each channel from 0.5-3 A and 3-10 A) is available; this monitors the 24 V

branches for overloading and short-circuiting (Figure 9-4 Electronic protection of 24 V loads

using the SITOP PSE200U selectivity module (Page 65)). Brief current peaks, e.g. as a

result of a high inrush current, are permitted, and branches with a longer overload are

switched into a no-current condition. This is also ensured for cables in a high-ohmic

condition and for short-circuits that slowly develop over time.

When a channel fails, the fault is signaled using a group signal contact or as a single

channel signal, and the branch of the module involved is displayed using an LED.

For variants with single-channel signaling, function blocks for evaluation purposes are

available for SIMATIC S7-1200/1500/300/400, for STEP 7 Classic and TIA Portal at no

charge.

You can find additional information at:

SITOP PSE200U selectivity module manuals

(http://support.automation.siemens.com/WW/view/en/10807226/130000)

Figure 9-4 Electronic protection of 24 V loads using the SITOP PSE200U selectivity module

Applications

9.5 Protection against short-time voltage dips

SITOP PSU100S

66 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

9.5

Protection against short-time voltage dips

For a drop in the line-side supply voltage, the SITOP PSU100S power supply still maintains

the output voltage for a short time in the millisecond range (see Chapter Technical data

(Page 39)).

For line supplies that manifest frequent brief voltage dips, in order to increase the power

supply reliability, it may make sense to increase the line buffering time in the device using an

additional SITOP PSE201U buffer module.

The SITOP PSE201U buffer module, based on electrolytic capacitors, is connected in

parallel to the 24 V power supply output (Figure 9-5 Buffering brief power failures using the

SITOP PSE201U buffer module (Page 66)). The buffer time is 200 ms at 40 A up to 1.6 s for

a load current of 5 A. This time can be increased a multiple number of times by connecting

buffer modules in parallel; the maximum buffer time is 10 s.

You can find additional information at:

SITOP PSE201U manual (http://support.automation.siemens.com/WW/view/en/41129219)

Figure 9-5 Buffering brief power failures using the SITOP PSE201U buffer module

Applications

9.6 Protecting against longer power failures

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 67

9.6

Protecting against longer power failures

Sudden and longer failures of the line supply voltage can result in undefined states and

significant danger as a result of the associated failure of the plant or system control. The

SITOP power supply product portfolio includes various DC-UPS solutions to prevent the

failure of the 24 V power supply voltage.

Power supply failures up into the minutes range can be buffered using the maintenance-free

SITOP UPS500 DC-UPS modules based on capacitors (Figure 9-6 24 V buffering to allow

the saving of process data and controlled shutdown of PCs (Page 67)).

Figure 9-6 24 V buffering to allow the saving of process data and controlled shutdown of PCs

Using the free-of-charge SITOP DC-UPS software tool, DC-UPS systems can be simply

integrated into PC-based automation solutions. This supports further processing of the status

signals and safely running down the PC.

You can find additional information at:

DC UPS with capacitors manual

(http://support.automation.siemens.com/WW/view/en/48932766/133300)

Applications

9.6 Protecting against longer power failures

SITOP PSU100S

68 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Using DC UPS SITOP UPS1600 and SITOP UPS100 battery modules, buffer times in the

range of hours can be implemented. Intelligent battery management using Energy Storage

Link automatically detects the UPS1100 energy storage device, and ensures optimum

temperature-controlled charging and continuous monitoring. The UPS1600 can be flexibly

integrated into the widest range of automation applications with its digital inputs/outputs as

well as optional USB interface or Ethernet/PROFINET port.

Figure 9-7 24 V buffering with SITOP UPS1600 to maintain communication, signaling functions,

sensor measured values and position values

For open, PC-based automation systems, configuration and monitoring is realized using the

SITOP UPS Manager PC software, which is available at no charge. This allows PC

responses to the operating states of the DC UPS to be freely selected – and offers

comprehensive diagnostic functions.

For TIA-based automation systems, the UPS1600 is engineered using the TIA Portal.

Special function blocks for SIMATIC S7-300/400/1200 and S7-1500 – available at no charge

– make it easy to integrate operating and diagnostics information into STEP 7 user

programs. Preconfigured UPS faceplates for WinCC visualization can be downloaded at no

charge.

You can find additional information at:

DC UPS SITOP UPS1600/UPS1100 Manual

(http://support.automation.siemens.com/WW/view/en/84977415)

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 69

Environment

The device is in conformance with RoHS.

As a rule, only non-silicon precipitating materials are used.

Disposal guidelines

Packaging and packaging aids can and should always be recycled. The product itself may

not be disposed of as domestic refuse.

Environment

SITOP PSU100S

70 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

SITOP PSU100S

Operating Instructions, 07.2014, C98130-A7589-A1-5-7629 71

Service & Support

Technical support

Technical support for all IA/DT products can be accessed through the following

communication channels:

● Phone: + 49 (0) 911 895 7222

● E-Mail (mailto:support.automation@siemens.com)

● Internet:

Online support request form (http://www.siemens.de/automation/support-request)

Technical documentation on the Internet

Operating instructions and manuals for SITOP are available in the Internet:

Operating instructions/manuals (http://www.siemens.de/sitop/manuals)

SITOP power supply homepage

General news about our power supplies is available in the Internet at the SITOP homepage:

SITOP (http://www.siemens.de/sitop)

Information material

SITOP information can be downloaded from the Internet:

Information and download center (http://www.siemens.de/sitop-infomaterial)

CAx data

2D/3D data and circuit diagram macros can be downloaded from the Internet:

Siemens image database (http://www.siemens.de/sitop-cax)

Request all CAx data via the CAx download manager:

CAx shopping cart (http://www.siemens.de/cax)

SITOP Selection Tool

Simply and quickly select the optimum the power supply or DC-UPS:

SITOP Selection Tool (http://www.siemens.de/sitop-selection-tool)

Online catalog and ordering system

The online catalog and the online ordering system are available through the Industry Mall

homepage:

Industry Mall (http://www.siemens.com/industrymall/de)

Service & Support

SITOP PSU100S

72 Operating Instructions, 07.2014, C98130-A7589-A1-5-7629

Contact persons

If you have any questions regarding the use of our products, then contact the Siemens

contact person in your regional Siemens sales office.

You can find these addresses as follows:

● On the Internet (http://www.siemens.de/automation/partner)

● In Catalog CA 01