CAT5114 32-Tap Digitally Programmable Potentiometer (DPPTM) FEATURES APPLICATIONS 32-position linear taper potentiometer Automated product calibration Non-volatile EEPROM wiper storage Remote control adjustments 10nA ultra-low standby current Offset, gain and zero control Single supply operation: 2.5V-6.0V Tamper-proof calibrations Increment Up/Down serial interface Contrast, brightness and volume controls , 50k and 100k Resistance values: 10k Motor controls and feedback systems Available in PDIP, SOIC, TSSOP, MSOP and space Programmable analog functions saving 2x3mm TDFN packages DESCRIPTION The CAT5114 is a single digitally programmable potentiometer (DPPTM) designed as a electronic replacement for mechanical potentiometers and trim pots. Ideal for automated adjustments on high volume production lines, they are also well suited for applications where equipment requiring periodic adjustment is either difficult to access or located in a hazardous or remote environment. new system values without effecting the stored setting. Wiper-control of the CAT5114 is accomplished with three input control pins, CS, U/D, and INC. The INC input increments the wiper in the direction which is determined by the logic state of the U/D input. The CS input is used to select the device and also store the wiper position prior to power down. The CAT5114 contains a 32-tap series resistor array connected between two terminals RH and RL. An up/ down counter and decoder that are controlled by three input pins, determines which tap is connected to the wiper, RW. The wiper setting, stored in nonvolatile memory, is not lost when the device is powered down and is automatically reinstated when power is returned. The wiper can be adjusted to test The digitally programmable potentiometer can be used as a three-terminal resistive divider or as a two-terminal variable resistor. DPPs bring variability and programmability to a wide variety of applications including control, parameter adjustments, and signal processing. FUNCTIONAL DIAGRAM Vcc (Supply Voltage) U/D INC CS R H / VH 31 5-BIT UP/DOWN COUNTER VH /R H 30 R H / VH UP/DOWN (U/D) INCREMENT (INC) 29 Control and Memory R W / VW POR R L / VL DEVICE SELECT (CS) 5-BIT NONVOLATILE MEMORY ONE 28 OF THIRTY TWO DECODER TRANSFER GATES VW / R W RESISTOR ARRAY 2 Vcc GND VSS STORE AND RECALL CONTROL CIRCUITRY 1 0 R L / VL R W / VW GENERAL GENERAL (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice DETAILED 1 VL / R L ELECTRONIC POTENTIOMETER IMPLEMENTATION Doc. No. 2007, Rev. M CAT5114 PIN CONFIGURATION PIN FUNCTIONS DIP Package (P, L, GL) INC U/D RH GND 1 8 VCC 2 7 3 6 CS RL 4 5 RW TSSOP Package (U, Y, GY) Pin Name CS VCC RL INC Increment Control RW GND RH U/D Up/Down Control RH Potentiometer High Terminal GND Ground RW Potentiometer Wiper Terminal INC U/D SOIC Package (S, V, GV) INC U/D RH GND 1 2 3 4 8 7 6 5 MSOP Package (R, Z, GZ) 1 8 VCC 2 7 3 6 CS RL INC U/D RH 4 5 RW GND Function 1 2 8 7 VCC CS RL Potentiometer Low Terminal 3 4 6 5 RL RW CS Chip Select VCC Supply Voltage TDFN Package (SP2, VP2, GP2) INC U/D RH GND 1 8 2 7 3 6 4 5 VCC CS RL RW Top View PIN DESCRIPTIONS INC INC: Increment Control Input RW: Wiper Potentiometer Terminal The INC input moves the wiper in the up or down direction determined by the condition of the U/D input. RW is the wiper terminal of the potentiometer. Its position on the resistor array is controlled by the control inputs, INC, U/D and CS. Voltage applied to the RW terminal cannot exceed the supply voltage, VCC or go below ground, GND. U/D D: Up/Down Control Input The U/D input controls the direction of the wiper movement. When in a high state and CS is low, any highto-low transition on INC will cause the wiper to move one increment toward the RH terminal. When in a low state and CS is low, any high-to-low transition on INC will cause the wiper to move one increment towards the RL terminal. RL: Low End Potentiometer Terminal RL is the low end terminal of the potentiometer. It is not required that this terminal be connected to a potential less than the RH terminal. Voltage applied to the RL terminal cannot exceed the supply voltage, VCC or go below ground, GND. R L and R H are electrically interchangeable. RH: High End Potentiometer Terminal RH is the high end terminal of the potentiometer. It is not required that this terminal be connected to a potential greater than the RL terminal. Voltage applied to the RH terminal cannot exceed the supply voltage, VCC or go below ground, GND. Doc. No. 2007, Rev. M CS CS: Chip Select The chip select input is used to activate the control input of the CAT5114 and is active low. When in a high state, activity on the INC and U/D inputs will not affect or change the position of the wiper. 2 (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5114 DEVICE OPERATION The CAT5114 operates like a digitally controlled potentiometer with RH and RL equivalent to the high and low terminals and RW equivalent to the mechanical potentiometer's wiper. There are 32 available tap positions including the resistor end points, RH and RL. There are 31 resistor elements connected in series between the R H and R L terminals. The wiper terminal is connected to one of the 32 taps and controlled by three inputs, INC, U/D and CS. These inputs control a five-bit up/down counter whose output is decoded to select the wiper position. The selected wiper position can be stored in nonvolatile memory using the INC and CS inputs. wiper (depending on the state of the U/D input and fivebit counter). The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. The value of the counter is stored in nonvolatile memory whenever CS transitions HIGH while the INC input is also HIGH. When the CAT5114 is powered-down, the last stored wiper counter position is maintained in the nonvolatile memory. When power is restored, the contents of the memory are recalled and the counter is set to the value stored. With INC set low, the CAT5114 may be de-selected and powered down without storing the current wiper position in nonvolatile memory. This allows the system to always power up to a preset value stored in nonvolatile memory. With CS set LOW the CAT5114 is selected and will respond to the U/D and INC inputs. HIGH to LOW transitions on INC wil increment or decrement the OPERATION MODES INC CS U/D Operation High to Low Low High Wiper toward H High to Low Low Low Wiper toward L High Low to High X Store Wiper Position Low Low to High X No Store, Return to Standby X High X Standby RH CH Rwi RW CW CL RL Potentiometer Equivalent Circuit (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 3 Doc. No. 2007, Rev. M CAT5114 Operating Ambient Temperature Commercial (`C' or Blank suffix) ...... 0C to +70C Industrial (`I' suffix) ...................... - 40C to +85C Junction Temperature ..................................... +150C Storage Temperature ....................... -65C to +150C Lead Soldering (10 sec max) .......................... +300C ABSOLUTE MAXIMUM RATINGS Supply Voltage VCC to GND ...................................... -0.5V to +7V Inputs CS to GND .............................-0.5V to VCC +0.5V INC to GND ............................-0.5V to VCC +0.5V U/D to GND ............................-0.5V to VCC +0.5V H to GND ................................-0.5V to VCC +0.5V L to GND ................................-0.5V to VCC +0.5V W to GND ............................... -0.5V to VCC +0.5V * Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Absolute Maximum Ratings are limited values applied individually while other parameters are within specified operating conditions, and functional operation at any of these conditions is NOT implied. Device performance and reliability may be impaired by exposure to absolute rating conditions for extended periods of time. RELIABILITY CHARACTERISTICS Symbol Parameter Test Method VZAP(1) ILTH(1)(2) ESD Susceptibility Latch-Up Data Retention Endurance MIL-STD-883, Test Method 3015 JEDEC Standard 17 MIL-STD-883, Test Method 1008 MIL-STD-883, Test Method 1003 TDR NEND Min Operating Voltage Range Supply Current (Increment) ICC2 Supply Current (Write) ISB1 (2) Supply Current (Standby) Max 2000 100 100 1,000,000 DC Electrical Characteristics: VCC = +2.5V to +6.0V unless otherwise specified Power Supply Symbol Parameter Conditions Min VCC ICC1 Typ Units Volts mA Years Stores Typ 2.5 Max Units 6.0 100 50 1 500 mA A 1 A Max Units 2 0 10 -10 VCC 0.8 A A V V VCC x 0.7 VCC + 0.3 V -0.3 VCC x 0.2 V VCC = 6V, f = 1MHz, IW=0 VCC = 6V, f = 250kHz, IW=0 Programming, VCC = 6V VCC = 3V CS=VCC-0.3V U/D, INC=VCC-0.3V or GND 0.01 V A Logic Inputs Symbol Parameter Conditions IIH IIL VIH1 VIL1 Input Leakage Current Input Leakage Current TTL High Level Input Voltage TTL Low Level Input Voltage VIN = VCC VIN = 0V 4.5V VCC 5.5V VIH2 CMOS High Level Input Voltage 2.5V VCC 6V VIL2 CMOS Low Level Input Voltage NOTES: (1) (2) (3) (4) Min Typ This parameter is tested initially and after a design or process change that affects the parameter. Latch-up protection is provided for stresses up to 100mA on address and data pins from -1V to VCC + 1V IW=source or sink These parameters are periodically sampled and are not 100% tested. Doc. No. 2007, Rev. M 4 (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5114 Potentiometer Parameters Symbol RPOT Parameter Potentiometer Resistance Conditions Min Typ -10 Device 10 -50 Device 50 -00 Device 100 Max Units k 20 % 0 VCC V 0 VCC V RTOL Pot Resistance Tolerance VRH Voltage on RH pin VRL Voltage on RL pin RES Resolution INL Integral Linearity Error IW 2A 0.5 1 LSB DNL Differential Linearity Error IW 2A 0.25 0.5 LSB RWi Wiper Resistance VCC = 5V, IW = 1mA 400 1 k 1 mA 3.2 VCC = 2.5V, IW = 1mA IW Wiper Current TCRPOT TC of Pot Resistance TCRATIO Ratiometric TC RISO Isolation Resistance VN Noise CH/CL/CW fc (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice ppm/oC 300 20 100kHz / 1kHz Potentiometer Capacitances Frequency Response % Passive Attenuator, 10k 5 ppm/oC TBD 8/24 nV/Hz 8/8/25 pF 1.7 MHz Doc. No. 2007, Rev. M CAT5114 AC CONDITIONS OF TEST VCC Range 2.5V VCC 6V Input Pulse Levels 0.2VCC to 0.7VCC Input Rise and Fall Times 10ns Input Reference Levels 0.5VCC AC OPERATING CHARACTERISTICS: VCC = +2.5V to +6.0V, VH = VCC, VL = 0V, unless otherwise specified Symbol Parameter Min tCI tDI tID tIL tIH tIC tCPH tCPH tIW tCYC tR, tF(2) tPU(2) tWR CS to INC Setup U/D to INC Setup U/D to INC Hold INC LOW Period INC HIGH Period INC Inactive to CS Inactive CS Deselect Time (NO STORE) CS Deselect Time (STORE) INC to VOUT Change INC Cycle Time INC Input Rise and Fall Time Power-up to Wiper Stable Store Cycle 100 50 100 250 250 1 100 10 Typ(1) Max 1 5 5 500 1 10 Units ns ns ns ns ns s ns ms s s s msec ms 1 A. C. TIMING CS (store) tCYC tCI tIL tIC tIH tCPH 90% INC 90% 10% tDI tID tF U/D tR MI (3) tIW RW (1) Typical values are for TA=25oC and nominal supply voltage. (2) This parameter is periodically sampled and not 100% tested. (3) MI in the A.C. Timing diagram refers to the minimum incremental change in the W output due to a change in the wiper position. Doc. No. 2007, Rev. M 6 (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5114 APPLICATION INFORMATION Potentiometer Configurations (a) resistive divider (b) variable resistance (c) two-port Applications 3 V1 (-) 2 + A1 R3 1 R4 +5V - +5V DPP +5V 8 2 9 1 R1 7 R2 10 R2 4 - +5V A3 8 + 6 7 11 4 V2 (+) 5 CAT5114 A2 - R3 R4 RB { { R1 6 5 3 } } pRPOT 7 4 8 3 (1-p)RPOT 555 R2 6 +2.5V 7 + RA 1 VO 4 CAT5114 8 2 5 2 1 C .01F .01F, .003F Programmable Instrumentation Amplifier Programmable Sq. Wave Oscillator (555) +5V 100k 8 2 CAT5114 1 7 V0 (REG) R1 2952 VIN (UNREG) 11k SHUTDOWN 1F SD GND FB .1 4 6.8F 6 +5V R2 +5V 820 2 8 2 3 5 CAT5114 4 IS R3 1 7 10k 3 - + (1-p)R 7 4 330 1M 3 5 +5V 10k 6 2 A1 3 - + 7 6 4 A2 VO LT1097 6 +2.5V Programmable Voltage Regulator (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice pR 330 1.23V } } VOUT Programmable I to V convertor 7 Doc. No. 2007, Rev. M CAT5114 APPLICATION INFORMATION R3 100k C1 .001 R1 50k 1 F +5V C2 VS .001 2 - 3 + +5V 7 6 4 VO A1 8 2 R2 10k 1 7 +2.5V 4 CAT5114 Programmable Bandpass Filter +5V IC1 393 IC2 74HC132 2 1 OSC CLO - + 3 R1 VLL R2 - + 7 10k 0.1F CHI 6 5 R3 +5V VUL +5V +5V 8 2 6 1 10k 7 4 IC3 CAT5114 5 3 - VO + AI IC4 VS +2.5V 2.5V < VO < 5V 0 < VS < 2.5V Automatic Gain Control Doc. No. 2007, Rev. M 8 (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice CAT5114 8-PAD TDFN 2 x 3 mm PACKAGE (SP2, VP2, GP2) A 0.75 + 0.05 MAX. 3.00 + 0.10 (S) B 2X 0.15C PIN 1 INDEX AREA 2.00 + 0.10 (S) 2X 0.15C 0.0 - 0.05 1.50 + 0.10 0.10C 0.20 REF. 8X 0.08C C 1 D D D D D D 2 D E G H J K Top Side Marking 1 2 3 4 5 6 7 8 1.85 + 0.10 Top Marking Device CAT5114SP2-00 CAT5114SP2-10 CAT5114SP2-50 CAT5114VP2-00 CAT5114VP2-10 CAT5114VP2-50 DAP SIZE 1.7 X 2.1 C0.35 1 4 0.25 + 0.05 (8X) 8X 0.10 M C AB 0.30 + 0.10 (8X) 0.50 TYP. (6X) 1.50 REF. (2X) NOTE: 1. ALL DIMENSIONS IN MM. ANGLES IN DEGREES. 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMNALS. COPLANARITY SHALL NOT EXCEED 0.08 MM. 3. WARPAGE SHALL NOT EXCEED 0.10 MM. 4. PACKAGE LENGTH / PACKAGE WIDTH ARE NOT CONSIDERED AS SPECIAL CHARACTERISTIC. (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice 9 Doc. No. 2007, Rev. M CAT5114 ORDERING INFORMATION Prefix CAT Optional Company ID Device # 5114 Suffix S I -10 Resistance -10: 10kohms -50: 50kohms -00: 100kohms Product Number TE13 Tape & Reel: TE13 SOIC: 2000/Reel TSSOP: 2000/Reel MSOP: 2500/Reel Tape & Reel: TE7 TDFN: 2000/Reel Package P: PDIP S: SOIC U: TSSOP R: MSOP SP2: TDFN L: PDIP (Lead free, Halogen free) V: SOIC (Lead free, Halogen free) Y: TSSOP (Lead free, Halogen free) Z: MSOP (Lead free, Halogen free) VP2: TDFN (Lead free, Halogen free) GL: PDIP (Lead-free, Halogen-free, NiPdAu lead plating) GV: SOIC, JEDEC (Lead-free, Halogen-free, NiPdAu lead plating) GY: TSSOP (Lead-free, Halogen-free, NiPdAu lead plating) GZ: MSOP (Lead-free, Halogen-free, NiPdAu lead plating) GP2: TDFN (Lead-free, Halogen-free, NiPdAu lead plating) Notes: (1) The device used in the above example is a CAT5114 SI-10TE13 (SOIC, 10K Ohms, Industrial Temperature, Tape & Reel) Doc. No. 2007, Rev. M 10 (c) 2005 by Catalyst Semiconductor, Inc. Characteristics subject to change without notice REVISION HISTORY Date Rev. Reason 10/9/2003 G Revised Features Revised DC Electrical Characteristics 3/10/2004 H Update Potentiometer Parameters 3/29/2004 I Changed Green Package marking for SOIC from W to V Updated Ordering Information (removed old 5112 references) 4/12/2004 J Updated Reel Ordering Information 8/31/2004 K Added TDFN package in all areas 04/08/2005 L Update Ordering Information 07/28/2005 M Update Pin Configuration Application Information Ordering Information Copyrights, Trademarks and Patents Trademarks and registered trademarks of Catalyst Semiconductor include each of the following: DPP TM AE2 TM MiniPotTM Catalyst Semiconductor has been issued U.S. and foreign patents and has patent applications pending that protect its products. For a complete list of patents issued to Catalyst Semiconductor contact the Company's corporate office at 408.542.1000. CATALYST SEMICONDUCTOR MAKES NO WARRANTY, REPRESENTATION OR GUARANTEE, EXPRESS OR IMPLIED, REGARDING THE SUITABILITY OF ITS PRODUCTS FOR ANY PARTICULAR PURPOSE, NOR THAT THE USE OF ITS PRODUCTS WILL NOT INFRINGE ITS INTELLECTUAL PROPERTY RIGHTS OR THE RIGHTS OF THIRD PARTIES WITH RESPECT TO ANY PARTICULAR USE OR APPLICATION AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILITY ARISING OUT OF ANY SUCH USE OR APPLICATION, INCLUDING BUT NOT LIMITED TO, CONSEQUENTIAL OR INCIDENTAL DAMAGES. Catalyst Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Catalyst Semiconductor product could create a situation where personal injury or death may occur. Catalyst Semiconductor reserves the right to make changes to or discontinue any product or service described herein without notice. Products with data sheets labeled "Advance Information" or "Preliminary" and other products described herein may not be in production or offered for sale. Catalyst Semiconductor advises customers to obtain the current version of the relevant product information before placing orders. Circuit diagrams illustrate typical semiconductor applications and may not be complete. Catalyst Semiconductor, Inc. Corporate Headquarters 1250 Borregas Avenue Sunnyvale, CA 94089 Phone: 408.542.1000 Fax: 408.542.1200 www.caalyst-semiconductor.com Publication #: Revison: Issue date: 2007 M 07/28/05