IP140A SERIES
IP140 SERIES
IP7800A SERIES
IP7800 SERIES
LM140 SERIES
Document Number 2833
Issue 2
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Pin 1 – VIN
Pin 2 – VOUT
Case – Ground
K Package – TO–3
Pin 1 – VIN
Pin 2 – VOUT
Case – Ground
R Package – TO–66
12
3
3
12
Pin 1 – VIN
Pin 2 – Ground
Pin 3 – VOUT
Case – Ground*
G Package – TO–257
IG Package– TO–257*
* isolated Case on IG package
1
23
Pin 1 – VIN
Pin 2 – Ground
Pin 3 – VOUT
SMD 1 PACKAGE
Ceramic Surface Mount
13
2
1 AMP POSITIVE
VOLTAGE REGULATOR
FEATURES
• OUTPUT CURRENT UP TO 1.0A
• OUTPUT VOLTAGES OF 5, 12, 15V
• 0.01% / V LINE REGULATION
• 0.3% / A LOAD REGULATION
• THERMAL OVERLOAD PROTECTION
• SHORT CIRCUIT PROTECTION
• OUTPUT TRANSISTOR SOA PROTECTION
• 1% VOLTAGE TOLERANCE (–A VERSIONS)
VIDC Input Voltage (for VO= 5, 12, 15V)
PDPower Dissipation
TjOperating Junction Temperature Range
Tstg Storage Temperature
35V
Internally limited 1
–55 to 150°C
–65 to 150°C
ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated)
Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX
of 20W. IMAX = 1.0A.
DESCRIPTION
The IP140A / LM140 / IP7800A / IP7800 series of
3 terminal regulators is available with several fixed output
voltage making them useful in a wide range of applications.
The A suffix devices are fully specified at 1A,
provide 0.01% / V line regulation, 0.3% / A load regulation
and ±1% output voltage tolerance at room temperature.
Protection features include Safe Operating Area current
limiting and thermal shutdown.
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
LCC4
CERAMIC SURFACE
MOUNT
Pins 4,5 – VIN .
Pins 6,7,8,9,10,11,12,13 – VOUT
Pins 15,16,17,18,1,2 – Ground
15 16
13
12 14
17
18
1
2
3456
7
11
10
8
9
2
1 3
2.41 (0.095)
(0.030)
min.
3.05 (0.120)
5.72 (.225)
0.127 (0.005)
(0.296)
10.16 (0.400)
0.76
(0.030)
min.
3.175 (0.125)
Max.
0.50 (0.020)
max.
7.54
0.76
2.41 (0.095)
0.127 (0.005)
(0.286) 7.26
16 PLCS
0.50(0.020)
0.127 (0.005)
Pin 1 – VIN
Pin 2 – Ground
Pin 3 – VOUT
SMD 05 PACKAGE
Ceramic Surface Mount
VOOutput Voltage
VOLow Supply
ΔVOLine Regulation
ΔVOLoad Regulation
IQQuiescent Current
ΔIQQuiescent Current
Change
VNOutput Noise
Voltage
ΔVIN Ripple Rejection
ΔVO
Dropout Voltage
ROOutput Resistance
Isc Short Circuit Current
Ipk Peak Output Current
Average Temperature
Coefficient of VO
Input Voltage required to
maintain line regulation
IP7805A IP7805
LM,IP140A–05 LM,IP140–05
Parameter Test Conditions Min. Typ. Max. Min. Typ. Max. Units
IO= 1A VIN = 10V
IO= 5mA to IMAX PD≤PMAX
VIN = 7.5V to 20V TJ= -55 to 150°C
IO= 5mA to IMAX PD≤PMAX
VIN = 7V to 20V
VIN = 7V to 25V
IO= 0.5 IMAX VIN = 7.5V to 25V
TJ= -55 to 150°C
IO≤IMAX VIN = 7.3V to 20V
VIN = 8V to 12V
TJ= -55 to 150°C
IO= 5mA to 1.5A
VIN = 10V IO= 250mA to 750mA
IO= 5mA to IMAX
VIN = 10V TJ= -55 to 150°C
IO≤IMAX
VIN = 10V TJ= -55 to 150°C
IO= 5mA to IMAX VIN = 10V
VIN = 7.5V to 20V
IO≤IMAX TJ= -55 to 150°C
IO≤0.5 IMAX VIN = 8V to 25V
IO≤0.5 IMAX VIN = 7V to 25V
TJ= -55 to 150°C
f = 10Hz to 100kHz
VIN = 10V
IO≤IMAX
f = 120Hz IO≤0.5 IMAX
VIN = 8V to 18V TJ= -55 to 150°C
IO= IMAX
f = 1 kHz
VIN = 35V
VIN = 10V
IO= 5mA
IO≤IMAX
IP140A SERIES
IP140 SERIES
IP7800A SERIES
IP7800 SERIES
LM140 SERIES
Document Number 2833
Issue 2
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
4.8 5 5.2
4.75 5.25
4.75 5.25
50
50
50
20
25
50
25
50
6
7
0.5
0.8
0.8
1.0
40
68
68
2
5
0.6 1.2
2.4 3.3
0.6
7.3
4.95 5 5.05
4.85 5.15
4.75 5.15
310
310
310
14
212
10 25
415
725
46
4 6.5
0.2 0.5
0.1 0.8
0.1 0.8
0.2 1
40 200
68 80
68 80
2 2.5
5
0.6 1.2
2.4 3.3
0.2 2
7.3
V
V
mV
mV
mA
mA
μV
dB
V
mΩ
A
mV
°C
V
1) All characteristics are measured with a capacitor across the input of 0.22μF and a capacitor across the output of 0.1μF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp≤10ms, δ≤5%). Output
voltage changes due to changes in internal temperature must be taken into account separately.
2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W ,
IMAX = 1.0A.
3) TJ= 25°C unless otherwise stated.
IP140A SERIES
IP140 SERIES
IP7800A SERIES
IP7800 SERIES
LM140 SERIES
Document Number 2833
Issue 2
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
1) All characteristics are measured with a capacitor across the input of 0.22μF and a capacitor across the output of 0.1μF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp≤10ms, δ≤5%). Output
voltage changes due to changes in internal temperature must be taken into account separately.
2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W ,
IMAX = 1.0A.
3) TJ= 25°C unless otherwise stated.
VOOutput Voltage
VOLow Supply
ΔVOLine Regulation
ΔVOLoad Regulation
IQQuiescent Current
ΔIQQuiescent Current
Change
VNOutput Noise
Voltage
ΔVIN Ripple Rejection
ΔVO
Dropout Voltage
ROOutput Resistance
Isc Short Circuit Current
Ipk Peak Output Current
Average Temperature
Coefficient of VO
Input Voltage required to
maintain line regulation
IP7812A IP7812
LM,IP140A–12 LM,IP140–12
Parameter Test Conditions Min. Typ. Max. Min. Typ. Max. Units
IO= 1A VIN = 19V
IO= 5mA to IMAX PD≤PMAX
VIN = 14.8V to 27V TJ= -55 to 150°C
IO= 5mA to IMAX PD≤PMAX
VIN = 14.5V to 27V
VIN = 14.5V to 30V
IO= 0.5 IMAX VIN = 14.8V to 30V
TJ= -55 to 150°C
IO≤IMAX VIN = 14.5V to 27V
VIN = 16V to 22V
TJ= -55 to 150°C
IO= 5mA to 1.5A
VIN = 19V IO= 250mA to 750mA
VIN = 19V IO= 5mA to IMAX
TJ= -55 to 150°C
IO≤IMAX
VIN = 19V TJ= -55 to 150°C
IO= 5mA to IMAX VIN = 19V
IO≤IMAX VIN = 14.8V to 27V
TJ= -55 to 150°C
IO≤0.5 IMAX VIN = 15V to 30V
IO≤0.5 IMAX VIN = 14.5V to 30V
TJ= -55 to 150°C
f = 10Hz to 100kHz
VIN = 19V
IO≤IMAX
f = 120Hz IO≤0.5 IMAX
VIN = 15V to 25V TJ= -55 to 150°C
IO= IMAX
f = 1 kHz
VIN = 35V
VIN = 19V
IO= 5mA
IO≤IMAX
11.5 12 12.5
11.4 12.6
11.4 12.6
120
120
120
50
60
120
60
120
6
7
0.5
0.8
0.8
1
75
61
61
2
8
0.6 1.2
2.4 3.3
1.5
14.6
11.88 12 12.12
11.64 12.36
11.40 12.36
418
418
418
29
430
12 32
419
860
46
4 6.5
0.2 0.5
0.1 0.8
0.1 0.8
0.2 1
75 480
61 72
61 72
2 2.5
8
0.6 1.2
2.4 3.3
0.5 4.8
14.5
V
V
mV
mV
mA
mA
μV
dB
V
mΩ
A
mV
°C
V
IP140A SERIES
IP140 SERIES
IP7800A SERIES
IP7800 SERIES
LM140 SERIES
Document Number 2833
Issue 2
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
1) All characteristics are measured with a capacitor across the input of 0.22μF and a capacitor across the output of 0.1μF.
All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp≤10ms, δ≤5%). Output
voltage changes due to changes in internal temperature must be taken into account separately.
2) Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 20W ,
IMAX = 1.0A.
3) TJ= 25°C unless otherwise stated.
VOOutput Voltage
VOLow Supply
ΔVOLine Regulation
ΔVOLoad Regulation
IQQuiescent Current
ΔIQQuiescent Current
Change
VNOutput Noise
Voltage
ΔVIN Ripple Rejection
ΔVO
Dropout Voltage
ROOutput Resistance
Isc Short Circuit Current
Ipk Peak Output Current
Average Temperature
Coefficient of VO
Input Voltage required to
maintain line regulation
IP7815A IP7815
LM,IP140A–15 LM,IP140–15
Parameter Test Conditions Min. Typ. Max. Min. Typ. Max. Units
IO= 1A VIN = 23V
IO= 5mA to IMAX PD≤PMAX
VIN = 17.9V to 30V TJ= -55 to 150°C
IO= 5mA to IMAX PD≤PMAX
VIN = 17.5V to 30V
VIN = 17.5V to 30V
IO= 0.5 IMAX VIN = 17.9V to 30V
TJ= -55 to 150°C
IO≤IMAX VIN = 17.5V to 30V
VIN = 20V to 26V
TJ= -55 to 150°C
IO= 5mA to 1.5A
VIN = 23V IO= 250mA to 750mA
VIN = 23V IO= 5mA to IMAX
TJ= -55 to 150°C
IO≤IMAX
VIN = 23V TJ= -55 to 150°C
IO= 5mA to IMAX VIN = 23V
IO≤IMAX VIN = 17.9V to 30V
TJ= -55 to 150°C
IO≤0.5 IMAX VIN = 18.5V to 30V
IO≤0.5 IMAX VIN = 17.5V to 30V
TJ= -55 to 150°C
f = 10Hz to 100kHz
VIN = 23V
f = 120Hz IO≤IMAX
VIN = 18.5V to IO≤0.5 IMAX
28.5V TJ= -55 to 150°C
IO= IMAX
f = 1 kHz
VIN = 35V
VIN = 23V
IO= 5mA
IO≤IMAX
14.4 15 15.60
14.25 15.75
14.25 15.75
150
150
150
60
75
150
75
150
6
7
0.5
0.8
0.8
1
90
60
60
2
9
0.6 1.2
2.4 3.3
1.8
17.7
14.85 15 15.15
14.55 15.45
14.25 15.45
422
422
422
210
530
12 35
421
975
46
4 6.5
0.2 0.5
0.1 0.8
0.1 0.8
0.2 1
90 600
60 70
60 70
2 2.5
9
0.6 1.2
2.4 3.3
0.6 6
17.5
V
V
mV
mV
mA
mA
μV
dB
V
mΩ
A
mV
°C
V
IP140A SERIES
IP140 SERIES
IP7800A SERIES
IP7800 SERIES
LM140 SERIES
Document Number 2833
Issue 2
Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612.
E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
GND
V
IN
V
OUT
C1*
0.22
μ
FC2**
INPUT OUTPUT
GND
V
IN
V
OUT
C1
0.22
μ
F
INPUT OUTPUT
R1
R2
R1
GND
V
IN
V
OUT
C1*
0.22
μ
F
INPUT
OUTPUT
I
OUT
Fixed Output Regulator
* Required if the regulator is located far from
the power supply.
** Although no output capacitor is needed for
stability, it does help transient response.(If
needed, use 0.1μF ceramic disc)
Current RegulatorAdjustable Output Regulator
APPLICATIONS INFORMATION
Part K–Pack R–Pack G/IG–Pack SMD 1 LCC4 Temp.
Number (TO–3) (TO–66) (TO–257) SMD 05 Range
IP7800A 33333-55 to +150°C
IP7800 33333 ”
IP140A 33333 ”
IP140 33333 ”
LM140 33333 ”
Note:
To order, add the package identifier
to the part number.
eg. IP7805AK
IP140SMD-12
Order Information
Semelab Plc reserves the right to change test conditions, parameter limits and package dimensions without notice. Information furnished by Semelab is believed
to be both accurate and reliable at the time of going to press. However Semelab assumes no responsibility for any errors or omissions discovered in its use.
Semelab encourages customers to verify that datasheets are current before placing orders.
Rthj-case Thermal Resistance Junction-case
MAX
3°C/W
7°C/W
5°C/W
13°C/W
1.3°C/W
K–Pack
R–Pack
G/IG–Pack
LCC4
SMD
THERMAL DATA
