LMV341. . . DBV (SOT-23) OR DCK (SC-70) PACKAGE
(TOP VIEW)
1
2
3
6
5
4
IN+
GND
IN−
V+
SHDN
OUT
1
2
3
4
8
7
6
5
1OUT
1IN−
1IN+
GND
V+
2OUT
2IN−
2IN+
LMV342. . . D (SOIC) OR DGK (MSOP) PACKAGE
(TOP VIEW)
LMV344. . . D (SOIC) OR PW (TSSOP) PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN−
1IN+
V+
2IN+
2IN−
2OUT
4OUT
4IN−
4IN+
GND
3IN+
3IN−
3OUT
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
RAIL-TO-RAIL OUTPUT CMOS OPERATIONAL AMPLIFIERS
WITH SHUTDOWN
Check for Samples: LMV341,LMV342,LMV344
1FEATURES
2.7-V and 5-V Performance
Rail-to-Rail Output Swing
Input Bias Current…1 pA Typ
Input Offset Voltage…0.25 mV Typ
Low Supply Current…100 μA Typ
Low Shutdown Current…45 pA Typ
Gain Bandwidth of 1 MHz Typ
Slew Rate…1 V/μs Typ
Turn-On Time From Shutdown…5 μs Typ
Input Referred Voltage Noise (at 10 kHz)…
20 nV/Hz
ESD Protection Exceeds JESD 22
2000-V Human-Body Model (A114-A)
200-V Machine Model (A115-A)
APPLICATIONS
Cordless/Cellular Phones
Consumer Electronics (Laptops, PDAs)
Audio Pre-Amps for Voice
Portable/Battery-Powered Electronic
Equipment
Supply-Current Monitoring
Battery Monitoring
Buffers
Filters
Drivers
DESCRIPTION/ORDERING INFORMATION
The LMV341, LMV342, LMV344 devices are single, dual, and quad CMOS operational amplifiers, respectively,
with low voltage, low power, and rail-to-rail output swing capabilities. The PMOS input stage offers an ultra-low
input bias current of 1 pA (typ) and an offset voltage of 0.25 mV (typ). The single supply amplifier is designed
specifically for low-voltage (2.7 V to 5 V) operation, with a wide common-mode input voltage range that typically
extends from –0.2 V to 0.8 V from the positive supply rail. The LMV341 (single) also offers a shutdown (SHDN)
pin that can be used to disable the device. In shutdown mode, the supply current is reduced to 33 nA (typ).
Additional features of the family are a 20-nV/Hz voltage noise at 10 kHz, 1-MHz unity-gain bandwidth, 1-V/μs
slew rate, and 100-μA current consumption per channel.
Offered in both the SOT-23 and smaller SC-70 packages, the LMV341 is suitable for the most space-constraint
applications. The LMV342 dual device is offered in the standard SOIC and MSOP packages. An extended
industrial temperature range from –40°C to 125°C makes these devices suitable in a wide variety of commercial
and industrial environments.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright © 2004–2012, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
V+
VO
+
VI
+
C = 200 pF
V+
Sample
Clock
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
ORDERING INFORMATION
TAPACKAGE(1) ORDERABLE PART NUMBER TOP-SIDE MARKING(2)
Reel of 3000 LMV341IDBVR RC9_
SOT-23 DBV Reel of 250 LMV341IDBVT Product Preview
Single Reel of 3000 LMV341IDCKR R4_
SC-70 DCK Reel of 250 LMV341IDCKT Product Preview
Tube of 75 LMV342ID
SOIC D MV342I
Reel of 2500 LMV342IDR
–40°C to 125°C Dual Reel of 250 LMV342IDGK
MSOP/VSSOP DGK RP_
Reel of 2500 LMV342IDGKR
Tube of 50 LMV344ID
SOIC D LMV344I
Reel of 2500 LMV344IDR
Quad Tube of 90 LMV344IPW
TSSOP PW MV344I
Reel of 2000 LMV344IPWR
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
(2) DBV/DCK/DGK: The actual top-side marking has one additional character that designates the wafer fab/assembly site.
Figure 1. APPLICATION CIRCUIT: SAMPLE-AND-HOLD CIRCUIT
2Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
ABSOLUTE MAXIMUM RATINGS(1)
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
V+Supply voltage(2) 5.5 V
VID Differential input voltage(3) ±5.5 V
VIInput voltage range (either input) 0 5.5 V
8 pin 97
D package 14 pin 86
DBV package 165
θJA Package thermal impedance(4) (5) °C/W
DCK package 259
DGK package 172
PW package 113
TJOperating virtual junction temperature 150 °C
Tstg Storage temperature range –65 150 °C
(1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating
conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values (except differential voltages and V+specified for the measurement of IOS) are with respect to the network GND.
(3) Differential voltages are at IN+ with respect to IN.
(4) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD= (TJ(max) TA)/θJA. Operating at the absolute maximum TJof 150°C can affect reliability.
(5) The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS MIN MAX UNIT
V+Supply voltage (single-supply operation) 2.5 5.5 V
TAOperating free-air temperature –40 125 °C
ESD PROTECTION TEST CONDITIONS TYP UNIT
Human-Body Model 2000 V
Machine Model 200 V
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): LMV341 LMV342 LMV344
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
V+= 2.7 V, GND = 0 V, VIC = VO= V+/2, RL> 1 M(unless otherwise noted)
PARAMETER TEST CONDITIONS TAMIN TYP(1) MAX UNIT
25°C 0.25 4
VIO Input offset voltage mV
Full range 4.5
Average temperature coefficient
αVIO Full range 1.7 μV/°C
of input offset voltage 25°C 1 120 pA
IIB Input bias current –40°C to 85°C 250
–40°C to 125°C 3 nA
IIO Input offset current 25°C 6.6 fA
0VICR 1.7 V 25°C 56 80
CMRR Common-mode rejection ratio dB
0VICR 1.6 V Full range 50
25°C 65 82
kSVR Supply-voltage rejection ratio 2.7 V V+5 V dB
Full range 60
Common-mode input voltage –0.2
VICR CMRR 50 dB 25°C 0 1.7 V
range to 1.9
25°C 78 113
RL= 10 kto 1.35 V Full range 70
AVLarge-signal voltage gain(2) dB
25°C 72 103
RL= 2 kto 1.35 V Full range 64
25°C 24 60
Low level Full range 95
RL= 2 kto 1.35 V 25°C 26 60
High level Full range 95
Output swing
VOmV
(delta from supply rails) 25°C 5 30
Low level Full range 40
RL= 10 kto 1.35 V 25°C 5.3 30
High level Full range 40
25°C 100 170
ICC Supply current (per channel) μA
Full range 230
LMV341, 20 32
LMV342
Sourcing
IOS Output short-circuit current 25°C mA
LMV344 18 24
Sinking 15 24
SR Slew rate RL= 10 k(3) 25°C 1 V/μs
GBM Unity-gain bandwidth RL= 10 k, CL= 200 pF 25°C 1 MHz
ΦmPhase margin RL= 100 k25°C 72 deg
GmGain margin RL= 100 k25°C 20 dB
VnEquivalent input noise voltage f = 1 kHz 25°C 40 nV/Hz
InEquivalent input noise current f = 1 kHz 25°C 0.001 pA/Hz
f = 1 kHz, AV= 1,
THD Total harmonic distortion 25°C 0.017 %
RL= 600 , VI= 1 VPP
(1) Typical values represent the most likely parametric norm.
(2) GND + 0.2 V VOV+ 0.2 V
(3) Connected as voltage follower with 2-VPP step input. Number specified is the slower of the positive and negative slew rates.
4Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
SHUTDOWN CHARACTERISTICS
V+= 2.7 V, GND = 0 V, VIC = VO= V+/2, RL> 1 M(unless otherwise noted)
PARAMETER TEST CONDITIONS TAMIN TYP MAX UNIT
25°C 0.045 1000 nA
ICC(SHDN) Supply current in shutdown mode VSD = 0 V Full range 1.5 μA
t(on) Amplifier turn-on time 25°C 5 μs
ON mode 1.7 to 2.7 2.4 to 2.7
VSD Shutdown pin voltage range 25°C V
Shutdown mode 0 to 1 0 to 0.8
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): LMV341 LMV342 LMV344
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
ELECTRICAL CHARACTERISTICS
V+= 5 V, GND = 0 V, VIC = VO= V+/2, RL> 1 M(unless otherwise noted)
PARAMETER TEST CONDITIONS TAMIN TYP(1) MAX UNIT
25°C 0.25 4
VIO Input offset voltage mV
Full range 4.5
Average temperature coefficient
αVIO Full range 1.9 μV/°C
of input offset voltage 25°C 1 200 pA
IIB Input bias current –40°C to 85°C 375
–40°C to 125°C 5 nA
IIO Input offset current 25°C 6.6 fA
0VICR 4 V 25°C 56 86
CMRR Common-mode rejection ratio dB
0VICR 3.9 V Full range 50
25°C 65 82
kSVR Supply-voltage rejection ratio 2.7 V V+5 V dB
Full range 60
Common-mode input –0.2
VICR CMRR 50 dB 25°C 0 4 V
voltage range to 4.2
25°C 78 116
RL= 10 kto 2.5 V Full range 70
AVLarge-signal voltage gain(2) dB
25°C 72 107
RL= 2 kto 2.5 V Full range 64
25°C 32 60
Low level Full range 95
RL= 2 kto 2.5 V 25°C 34 60
High level Full range 95
Output swing
VOmV
(delta from supply rails) 25°C 7 30
Low level Full range 40
RL= 10 kto 2.5 V 25°C 7 30
High level Full range 40
25°C 107 200
ICC Supply current (per channel) μA
Full range 260
LMV341, 85 113
LMV342
Sourcing
IOS Output short-circuit current 25°C mA
LMV344 85 113
Sinking 50 75
SR Slew rate RL= 10 k(3) 25°C 1 V/μs
GBM Unity-gain bandwidth RL= 10 k, CL= 200 pF 25°C 1 MHz
ΦmPhase margin RL= 100 k25°C 70 deg
GmGain margin RL= 100 k25°C 20 dB
VnEquivalent input noise voltage f = 1 kHz 25°C 39 nV/Hz
InEquivalent input noise current f = 1 kHz 25°C 0.001 pA/Hz
f = 1 kHz, AV= 1,
THD Total harmonic distortion 25°C 0.012 %
RL= 600 , VI= 1 VPP
(1) Typical values represent the most likely parametric norm.
(2) GND + 0.2 V VOV+ 0.2 V
(3) Connected as voltage follower with 2-VPP step input. Number specified is the slower of the positive and negative slew rates.
6Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
SHUTDOWN CHARACTERISTICS
V+= 5 V, GND = 0 V, VIC = VO= V+/2, RL> 1 M(unless otherwise noted)
PARAMETER TEST CONDITIONS TAMIN TYP MAX UNIT
25°C 0.033 1
ICC(SHDN) Supply current in shutdown mode VSD = 0 V μA
Full range 1.5
t(on) Amplifier turn-on time 25°C 5 μs
ON mode 3.1 to 5 4.5 to 5
VSD Shutdown pin voltage range 25°C V
Shutdown mode 0 to 1 0 to 0.8
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Link(s): LMV341 LMV342 LMV344
1.5 2 2.5 3 3.5 4 4.5 5
VO − Output Swing From Supply Voltage − mV
VCC − Supply V oltage − V
RL = 2 k
Negative Swing
Positive Swing
10
15
20
25
30
35
VO − Output Swing From Supply Voltage − mV
VCC − Supply V oltage − V
1.5 2 2.5 3 3.5 4 4.5 5
RL = 10 k
Negative Swing
Positive Swing
3
3.5
4
4.5
5
5.5
6
6.5
7
100
90
80
70
1.5 2 2.5 3 3.5 4 4.5
110
120
130
5
30
40
50
60
VCC − Supply V oltage − V
ICC − Supply Current − µA
125°C
85°C
25°C
−40°C
−40 −20 0 20 40 60 80 100 120 140
IIB − Input Bias Current − pA
TA − Free-Air Temperature − °C
V+ = 5 V
0.1
1
10
100
1000
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS
SUPPLY CURRENT INPUT BIAS CURRENT
vs vs
SUPPLY VOLTAGE TEMPERATURE
Figure 2. Figure 3.
OUTPUT VOLTAGE SWING OUTPUT VOLTAGE SWING
vs vs
SUPPLY VOLTAGE SUPPLY VOLTAGE
Figure 4. Figure 5.
8Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
0.001 0.01 0.1 1 10
IS − Sink Current − mA
VO − Output Voltage Referenced to V− (V)
V+ = 5 V
125°C
−40°C
85°C
25°C
0.01
0.1
1
10
100
1000
0.001 0.01 0.1 1 10
IS − Sink Current − mA
VO − Output Voltage Referenced to V− (V)
V+ = 2.7 V
125°C
−40°C
85°C
25°C
0.01
0.1
1
10
100
1000
0.001 0.01 0.1 1 10
IS − Source Current − mA
VO − Output Voltage Referenced to V+ (V)
V+ = 5 V
125°C
−40°C
85°C
25°C
0.01
0.1
1
10
100
1000
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
SOURCE CURRENT SOURCE CURRENT
vs vs
OUTPUT VOLTAGE OUTPUT VOLTAGE
Figure 6. Figure 7.
SINK CURRENT SINK CURRENT
vs vs
OUTPUT VOLTAGE OUTPUT VOLTAGE
Figure 8. Figure 9.
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Link(s): LMV341 LMV342 LMV344
VI − Input Voltage − µV
VO − Output Voltage − V
−3 −2 −1 0 1 2 3
V+ /GND = ±2.5 V
RL = 2 k
RL = 10 k
−300
−200
−100
0
100
200
300
VI − Input Voltage − µV
VO − Output Voltage − V
−1.5 −1 −0.5 0 0.5 1 1.5
V+ /GND = ±1.35 V
RL = 2 k
RL = 10 k
−300
−200
−100
0
100
200
300
−0.2 0.8 1.8 2.8 3.8 4.8 5.8
VIO − Offset Voltage − mV
VIC − Common-Mode Voltage − V
V+ = 5 V
−3
−2.5
−2
−1.5
−1
−0.5
0
0.5
1
−40°C
25°C
85°C
125°C
−0.2 0.8 1.8 2.8
VIO − Offset Voltage − mV
VIC − Common-Mode Voltage − V
V+ = 2.7 V
−3
−2.5
−2
−1.5
−1
−0.5
0
0.5
1
−40°C
25°C
85°C
125°C
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
OFFSET VOLTAGE OFFSET VOLTAGE
vs vs
COMMON-MODE VOLTAGE COMMON-MODE VOLTAGE
Figure 10. Figure 11.
INPUT VOLTAGE INPUT VOLTAGE
vs vs
OUTPUT VOLTAGE OUTPUT VOLTAGE
Figure 12. Figure 13.
10 Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
0
10
20
30
40
50
60
70
80
90
100
100 1k 10k 100k 1M
Gain − dB
f − Frequency − Hz
5 V
VI = V+ /2
RL = 5 k
2.7 V
SR Slew Rate V/µs
0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
2.1
2.3
2.5
−40 −20 0 20 40 60 80 100 120 140
RL= 10 kΩ
AV= 1
VI= 2 VPP
V+= 5 V
Rising Edge
Falling Edge
T Free-Air Temperature °C
A
SR Slew Rate V/µs
T Free-Air Temperature °C
A
0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
2.1
2.3
2.5
−40 −20 0 20 40 60 80 100 120 140
RL= 10 k
AV= 1
VI= 2 VPP
V+= 2.7 V
Rising Edge
Falling Edge
SR − Slew Rate − V/µs
VCC − Supply V oltage − V
0.5
0.7
0.9
1.1
1.3
1.5
1.7
1.9
1.5 2 2.5 3 3.5 4 4.5 5
Rising Edge
Falling Edge
RL = 10 k
AV = 1
VI = 0.8 VPP for V+ < 2.7 V
VI = 2 VPP for V+ > 2.7 V
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
SLEW RATE SLEW RATE
vs vs
SUPPLY VOLTAGE TEMPERATURE
Figure 14. Figure 15.
SLEW RATE CMRR
vs vs
TEMPERATURE FREQUENCY
Figure 16. Figure 17.
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Link(s): LMV341 LMV342 LMV344
THD+N − Total Harmonic Distortion + Noise − %
VO − Output Voltage − VPP
0.001 0.01 0.1 1 10
f = 10 kHz
RL = 600
5 V
AV = 10
5 V
AV = 1 2.7 V
AV = 1
2.7 V
AV = 10
0.01
0.1
1
10
VI − Input Voltage Noise − nV/
f − Frequency − Hz
0
20
40
60
80
100
120
140
160
180
200
220
10 100 1k 10k
2.7 V
5 V
Hz
0
10
20
30
40
50
60
70
80
90
100
100 1k 10k 100k 1M
Gain − dB
f − Frequency − Hz 10M
+PSRR (5 V)
+PSRR (2.7 V)
−PSRR (5 V)
RL = 5 k
−PSRR (2.7 V)
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PSRR INPUT VOLTAGE NOISE
vs vs
FREQUENCY FREQUENCY
Figure 18. Figure 19.
TOTAL HARMONIC DISTORTION + NOISE TOTAL HARMONIC DISTORTION + NOISE
vs vs
FREQUENCY OUTPUT VOLTAGE
Figure 20. Figure 21.
12 Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
Gain − dB
f − Frequency − Hz
Phase Margin − Deg
1k 10k 100k 1M 10M0
20
40
60
80
100
120
140
160
V+ = 2.7 V
Closed-Loop
Gain = 60 dB
RL = 100 k
RL = 2 kRL = 600
Gain
Phase
−20
0
20
40
60
80
100
120
140
RL = 600
RL = 100 k
RL = 2 k
Gain − dB
f − Frequency − Hz
Phase Margin − Deg
1k 10k 100k 1M 10M 0
20
40
60
80
100
120
140
160
V+ = 5 V
RL = 2 k
125°C
−40°C
25°C
Gain
Phase
−20
0
20
40
60
80
100
120
140
125°C
−40°C
25°C
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(TA= –40°C, 25°C, 125°C)
Figure 22.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(RL= 600 , 2 k, 100 k)
Figure 23.
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Link(s): LMV341 LMV342 LMV344
Gain − dB
f − Frequency − Hz
Phase Margin − Deg
1k 10k 100k 1M 10M−80
−60
−40
−20
0
20
40
60
80
100
CL = 0 pF
CL = 100 pF
CL = 500 pF
CL = 1000 pF
V+ = 5 V
RL = 600
Closed-Loop Gain = 60 dB
CL = 1000 pF
CL = 0 pF
CL = 500 pF
Gain
Phase
−20
0
20
40
60
80
100
120
140
−40 CL = 100 pF
Gain − dB
f − Frequency − Hz
1k 10k 100k 1M 10M0
20
40
60
80
100
120
140
160
V+ = 5 V
Closed-Loop
Gain = 60 dB
RL = 600
RL = 2 k
RL = 100 k
RL = 2 k
RL = 600
Phase Margin − Deg
Gain
Phase
−20
0
20
40
60
80
100
120
140
RL = 100 k
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
GAIN AND PHASE MARGIN
vs
FREQUENCY
(RL= 600 , 2 k, 100 k)
Figure 24.
GAIN AND PHASE MARGIN
vs
FREQUENCY
(CL= 0 pF, 100 pF, 500 pF, 1000 pF)
Figure 25.
14 Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
VI − Input Voltage − V
Input
TA = 25°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
4 µs/div"
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = 25°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = −40°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
VI − Input Voltage − V
Input
TA = −40°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
4 µs/div"
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
SMALL-SIGNAL NONINVERTING RESPONSE LARGE-SIGNAL NONINVERTING RESPONSE
Figure 26. Figure 27.
SMALL-SIGNAL NONINVERTING RESPONSE LARGE-SIGNAL NONINVERTING RESPONSE
Figure 28. Figure 29.
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Link(s): LMV341 LMV342 LMV344
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
VI − Input Voltage − V
Input
TA = −40°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
4 µs/div"
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = −40°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = 125°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
VI − Input Voltage − V
Input
TA = 125°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
4 µs/div"
LMV341, LMV342, LMV344
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
www.ti.com
TYPICAL CHARACTERISTICS (continued)
SMALL-SIGNAL NONINVERTING RESPONSE LARGE-SIGNAL NONINVERTING RESPONSE
Figure 30. Figure 31.
SMALL-SIGNAL INVERTING RESPONSE LARGE-SIGNAL INVERTING RESPONSE
Figure 32. Figure 33.
16 Submit Documentation Feedback Copyright © 2004–2012, Texas Instruments Incorporated
Product Folder Link(s): LMV341 LMV342 LMV344
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = 125°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
4 µs/div"
VI − Input Voltage − V
Input
TA = 125°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
−0.25
−0.2
−0.15
−0.1
−0.05
0
0.05
0.1
VO − Output Voltage − V
VI − Input Voltage − V
Input
TA = 25°C
RL = 2 k
V+/GND = ±2.5 V
Output
−0.1
−0.05
0
0.05
0.1
0.15
0.2
0.25
4 µs/div"
VO − Output Voltage − V
VI − Input Voltage − V
−6
−5
−4
−3
−2
−1
0
2
1
Input
Output
TA = 25°C
RL = 2 k
V+/GND = ±2.5 V
−2
−1
0
1
2
3
4
5
6
4 µs/div"
LMV341, LMV342, LMV344
www.ti.com
SLOS447H SEPTEMBER 2004REVISED JUNE 2012
TYPICAL CHARACTERISTICS (continued)
SMALL-SIGNAL INVERTING RESPONSE LARGE-SIGNAL INVERTING RESPONSE
Figure 34. Figure 35.
SMALL-SIGNAL INVERTING RESPONSE LARGE-SIGNAL INVERTING RESPONSE
Figure 36. Figure 37.
Copyright © 2004–2012, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Link(s): LMV341 LMV342 LMV344
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
LMV341IDBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV341IDBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV341IDBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV341IDCKR ACTIVE SC70 DCK 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV341IDCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV341IDCKRG4 ACTIVE SC70 DCK 6 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342ID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDDUR PREVIEW VSSOP DDU 8 3000 TBD Call TI Call TI
LMV342IDE4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDGKT PREVIEW VSSOP DGK 8 250 TBD Call TI Call TI
LMV342IDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDRE4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV342IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344ID ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IDE4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
LMV344IDG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IDR ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IDRE4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPW ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPWR ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LMV344IPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 3
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LMV341, LMV344 :
Automotive: LMV341-Q1, LMV344-Q1
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LMV341IDBVR SOT-23 DBV 6 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LMV341IDCKR SC70 DCK 6 3000 180.0 8.4 2.25 2.4 1.22 4.0 8.0 Q3
LMV342IDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LMV342IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
LMV344IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LMV344IPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Aug-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LMV341IDBVR SOT-23 DBV 6 3000 203.0 203.0 35.0
LMV341IDCKR SC70 DCK 6 3000 202.0 201.0 28.0
LMV342IDGKR VSSOP DGK 8 2500 358.0 335.0 35.0
LMV342IDR SOIC D 8 2500 340.5 338.1 20.6
LMV344IDR SOIC D 14 2500 367.0 367.0 38.0
LMV344IPWR TSSOP PW 14 2000 367.0 367.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 29-Aug-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated