LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 RAIL-TO-RAIL OUTPUT CMOS OPERATIONAL AMPLIFIERS WITH SHUTDOWN Check for Samples: LMV341, LMV342, LMV344 FEATURES 1 * * * * * * * * * * * 2.7-V and 5-V Performance Rail-to-Rail Output Swing Input Bias Current...1 pA Typ Input Offset Voltage...0.25 mV Typ Low Supply Current...100 A Typ Low Shutdown Current...45 pA Typ Gain Bandwidth of 1 MHz Typ Slew Rate...1 V/s Typ Turn-On Time From Shutdown...5 s Typ Input Referred Voltage Noise (at 10 kHz)... 20 nV/Hz ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) APPLICATIONS * * * * * * * * * Cordless/Cellular Phones Consumer Electronics (Laptops, PDAs) Audio Pre-Amps for Voice Portable/Battery-Powered Electronic Equipment Supply-Current Monitoring Battery Monitoring Buffers Filters Drivers LMV341 . . . DBV (SOT-23) OR DCK (SC-70) PACKAGE (TOP VIEW) IN+ GND IN- 1 6 2 5 3 4 V+ SHDN OUT LMV342 . . . D (SOIC) OR DGK (MSOP) PACKAGE (TOP VIEW) 1OUT 1IN- 1IN+ GND 1 8 2 7 3 6 4 5 V+ 2OUT 2IN- 2IN+ LMV344 . . . D (SOIC) OR PW (TSSOP) PACKAGE (TOP VIEW) 1OUT 1IN- 1IN+ V+ 2IN+ 2IN- 2OUT 1 14 2 13 3 12 4 11 5 10 6 7 9 8 4OUT 4IN- 4IN+ GND 3IN+ 3IN- 3OUT DESCRIPTION/ORDERING INFORMATION The LMV341, LMV342, LMV344 devices are single, dual, and quad CMOS operational amplifiers, respectively, with low voltage, low power, and rail-to-rail output swing capabilities. The PMOS input stage offers an ultra-low input bias current of 1 pA (typ) and an offset voltage of 0.25 mV (typ). The single supply amplifier is designed specifically for low-voltage (2.7 V to 5 V) operation, with a wide common-mode input voltage range that typically extends from -0.2 V to 0.8 V from the positive supply rail. The LMV341 (single) also offers a shutdown (SHDN) pin that can be used to disable the device. In shutdown mode, the supply current is reduced to 33 nA (typ). Additional features of the family are a 20-nV/Hz voltage noise at 10 kHz, 1-MHz unity-gain bandwidth, 1-V/s slew rate, and 100-A current consumption per channel. Offered in both the SOT-23 and smaller SC-70 packages, the LMV341 is suitable for the most space-constraint applications. The LMV342 dual device is offered in the standard SOIC and MSOP packages. An extended industrial temperature range from -40C to 125C makes these devices suitable in a wide variety of commercial and industrial environments. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2012, Texas Instruments Incorporated LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com ORDERING INFORMATION PACKAGE (1) TA SOT-23 - DBV Single SC-70 - DCK SOIC - D -40C to 125C Dual MSOP/VSSOP - DGK SOIC - D Quad TSSOP - PW (1) (2) TOP-SIDE MARKING (2) ORDERABLE PART NUMBER Reel of 3000 LMV341IDBVR RC9_ Reel of 250 LMV341IDBVT Product Preview Reel of 3000 LMV341IDCKR R4_ Reel of 250 LMV341IDCKT Product Preview Tube of 75 LMV342ID Reel of 2500 LMV342IDR Reel of 250 LMV342IDGK Reel of 2500 LMV342IDGKR Tube of 50 LMV344ID Reel of 2500 LMV344IDR Tube of 90 LMV344IPW Reel of 2000 LMV344IPWR MV342I RP_ LMV344I MV344I Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DCK/DGK: The actual top-side marking has one additional character that designates the wafer fab/assembly site. Figure 1. APPLICATION CIRCUIT: SAMPLE-AND-HOLD CIRCUIT V+ V+ - - VO + VI + C = 200 pF Sample Clock 2 Submit Documentation Feedback Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) MIN (2) V+ Supply voltage VID Differential input voltage (3) VI Input voltage range (either input) 0 D package JA Package thermal impedance (4) (5) TJ Operating virtual junction temperature Tstg Storage temperature range (1) (2) (3) (4) (5) 8 pin MAX UNIT 5.5 V 5.5 V 5.5 V 97 14 pin 86 DBV package 165 DCK package 259 DGK package 172 PW package 113 -65 C/W 150 C 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values (except differential voltages and V+ specified for the measurement of IOS) are with respect to the network GND. Differential voltages are at IN+ with respect to IN-. Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. RECOMMENDED OPERATING CONDITIONS MIN MAX UNIT V+ Supply voltage (single-supply operation) 2.5 5.5 V TA Operating free-air temperature -40 125 C ESD PROTECTION TEST CONDITIONS Human-Body Model Machine Model Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 TYP UNIT 2000 V 200 V Submit Documentation Feedback 3 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com ELECTRICAL CHARACTERISTICS V+ = 2.7 V, GND = 0 V, VIC = VO = V+/2, RL > 1 M (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Average temperature coefficient of input offset voltage IIB Input bias current TEST CONDITIONS TA MIN 25C 3 6.6 0 VICR 1.6 V Full range 50 25C 65 Full range 60 25C 0 -0.2 to 1.9 113 2.7 V V+ 5 V VICR Common-mode input voltage range CMRR 50 dB RL = 10 k to 1.35 V Large-signal voltage gain (2) RL = 2 k to 1.35 V Low level RL = 2 k to 1.35 V High level Output swing (delta from supply rails) Low level RL = 10 k to 1.35 V High level ICC -40C to 125C 56 Supply-voltage rejection ratio VO 250 25C kSVR 25C 78 Full range 70 25C 72 Full range 64 25C 26 Full range V dB 60 60 95 25C 5 Full range 30 mV 40 25C 5.3 30 100 170 Full range 40 230 20 32 18 24 15 24 A IOS Output short-circuit current SR Slew rate RL = 10 k (3) 25C 1 V/s GBM Unity-gain bandwidth RL = 10 k, CL = 200 pF 25C 1 MHz m Phase margin RL = 100 k 25C 72 deg Gm Gain margin RL = 100 k 25C 20 dB Vn Equivalent input noise voltage f = 1 kHz 25C 40 nV/Hz In Equivalent input noise current f = 1 kHz 25C 0.001 pA/Hz THD Total harmonic distortion f = 1 kHz, AV = 1, RL = 600 , VI = 1 VPP 25C 0.017 % LMV344 25C 1.7 95 25C LMV341, LMV342 nA dB 103 Full range Sourcing pA dB 82 24 mV fA 80 Full range 25C Supply current (per channel) 120 -40C to 85C 25C Common-mode rejection ratio AV 1 UNIT V/C 1.7 0 VICR 1.7 V CMRR 4 4.5 Full range Input offset current MAX 0.25 Full range 25C IIO TYP (1) Sinking (1) (2) (3) 4 mA Typical values represent the most likely parametric norm. GND + 0.2 V VO V+ - 0.2 V Connected as voltage follower with 2-VPP step input. Number specified is the slower of the positive and negative slew rates. Submit Documentation Feedback Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 SHUTDOWN CHARACTERISTICS V+ = 2.7 V, GND = 0 V, VIC = VO = V+/2, RL > 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS ICC(SHDN) Supply current in shutdown mode t(on) Amplifier turn-on time VSD VSD = 0 V TA 25C Shutdown pin voltage range Shutdown mode TYP MAX 0.045 1000 nA 1.5 A Full range 25C ON mode MIN 25C Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 s 5 1.7 to 2.7 2.4 to 2.7 0 to 1 UNIT 0 to 0.8 Submit Documentation Feedback V 5 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com ELECTRICAL CHARACTERISTICS V+ = 5 V, GND = 0 V, VIC = VO = V+/2, RL > 1 M (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Average temperature coefficient of input offset voltage IIB Input bias current TEST CONDITIONS TA MIN 25C CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio 2.7 V V+ 5 V VICR Common-mode input voltage range CMRR 50 dB 0 VICR 3.9 V RL = 10 k to 2.5 V Large-signal voltage gain (2) AV RL = 2 k to 2.5 V Low level RL = 2 k to 2.5 V High level Output swing (delta from supply rails) VO Low level RL = 10 k to 2.5 V High level ICC 1 375 -40C to 125C 5 6.6 56 Full range 50 25C 65 Full range 60 25C 0 -0.2 to 4.2 116 25C 78 Full range 70 25C 72 Full range 64 25C 34 Full range V dB 60 60 95 25C 7 Full range 30 mV 40 25C 7 30 107 200 Full range 40 260 85 113 85 113 50 75 A IOS Output short-circuit current SR Slew rate RL = 10 k (3) 25C 1 V/s GBM Unity-gain bandwidth RL = 10 k, CL = 200 pF 25C 1 MHz m Phase margin RL = 100 k 25C 70 deg Gm Gain margin RL = 100 k 25C 20 dB Vn Equivalent input noise voltage f = 1 kHz 25C 39 nV/Hz In Equivalent input noise current f = 1 kHz 25C 0.001 pA/Hz THD Total harmonic distortion f = 1 kHz, AV = 1, RL = 600 , VI = 1 VPP 25C 0.012 % LMV344 25C 4 95 25C LMV341, LMV342 nA dB 107 Full range Sourcing pA dB 82 32 mV fA 86 Full range 25C Supply current (per channel) 200 -40C to 85C 25C UNIT V/C 1.9 25C 0 VICR 4 V 4 4.5 Full range Input offset current MAX 0.25 Full range 25C IIO TYP (1) Sinking (1) (2) (3) 6 mA Typical values represent the most likely parametric norm. GND + 0.2 V VO V+ - 0.2 V Connected as voltage follower with 2-VPP step input. Number specified is the slower of the positive and negative slew rates. Submit Documentation Feedback Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 SHUTDOWN CHARACTERISTICS V+ = 5 V, GND = 0 V, VIC = VO = V+/2, RL > 1 M (unless otherwise noted) PARAMETER TEST CONDITIONS ICC(SHDN) Supply current in shutdown mode t(on) Amplifier turn-on time VSD VSD = 0 V TA 25C Shutdown pin voltage range Shutdown mode TYP 0.033 Full range 25C ON mode MIN 25C Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 MAX 1 1.5 UNIT A s 5 3.1 to 5 4.5 to 5 0 to 1 0 to 0.8 Submit Documentation Feedback V 7 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS SUPPLY CURRENT vs SUPPLY VOLTAGE INPUT BIAS CURRENT vs TEMPERATURE 130 1000 V+ = 5 V 120 125C 100 90 80 IIB - Input Bias Current - pA ICC - Supply Current - A 110 85C 25C 70 60 50 -40C 100 10 1 40 30 1.5 2 2.5 3 3.5 4 4.5 0.1 -40 -20 5 0 20 40 60 80 100 120 TA - Free-Air Temperature - C Figure 3. VCC - Supply Voltage - V Figure 2. OUTPUT VOLTAGE SWING vs SUPPLY VOLTAGE 35 7 RL = 2 k VO - Output Swing From Supply Voltage - mV VO - Output Swing From Supply Voltage - mV OUTPUT VOLTAGE SWING vs SUPPLY VOLTAGE 30 Negative Swing 25 20 Positive Swing 15 10 1.5 8 140 2 2.5 3 3.5 4 VCC - Supply Voltage - V Figure 4. Submit Documentation Feedback 4.5 5 RL = 10 k 6.5 6 Negative Swing 5.5 5 4.5 4 Positive Swing 3.5 3 1.5 2 2.5 3 3.5 4 4.5 5 VCC - Supply Voltage - V Figure 5. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) SOURCE CURRENT vs OUTPUT VOLTAGE SOURCE CURRENT vs OUTPUT VOLTAGE 1000 1000 V+ = 5 V V+ = 2.7 V IS - Source Current - mA IS - Source Current - mA -40C 100 100 -40C 25C 10 85C 1 125C 10 25C 85C 1 125C 0.1 0.1 0.01 0.001 0.01 0.1 1 VO - Output Voltage Referenced to V+ (V) Figure 6. 0.01 0.001 10 0.01 0.1 1 VO - Output Voltage Referenced to V+ (V) Figure 7. SINK CURRENT vs OUTPUT VOLTAGE SINK CURRENT vs OUTPUT VOLTAGE 1000 V+ = 2.7 V V+ = 5 V 100 100 -40C -40C IS - Sink Current - mA IS - Sink Current - mA 1000 10 25C 85C 1 125C 0.1 0.01 0.001 10 10 25C 85C 1 125C 0.1 0.01 0.1 1 VO - Output Voltage Referenced to V- (V) Figure 8. 10 0.01 0.001 0.01 0.1 1 VO - Output Voltage Referenced to V- (V) Figure 9. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 Submit Documentation Feedback 10 9 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) OFFSET VOLTAGE vs COMMON-MODE VOLTAGE OFFSET VOLTAGE vs COMMON-MODE VOLTAGE 1 1 V+ = 5 V 0.5 0.5 0 0 VIO - Offset Voltage - mV VIO - Offset Voltage - mV V+ = 2.7 V -0.5 -1 125C -1.5 85C -2 25C -0.5 -1 125C 85C -1.5 25C -2 -40C -40C -2.5 -2.5 -3 -0.2 0.8 1.8 -3 -0.2 2.8 VIC - Common-Mode Voltage - V Figure 10. 0.8 1.8 2.8 3.8 4.8 VIC - Common-Mode Voltage - V Figure 11. INPUT VOLTAGE vs OUTPUT VOLTAGE INPUT VOLTAGE vs OUTPUT VOLTAGE 300 300 V+ /GND = 1.35 V V+ /GND = 2.5 V VI - Input Voltage - V VI - Input Voltage - V 200 RL = 2 k 100 0 RL = 10 k 200 0 -100 -200 -200 -2 -1 0 1 2 3 RL = 2 k 100 -100 -300 -3 -300 -1.5 RL = 10 k -1 Submit Documentation Feedback -0.5 0 0.5 1 1.5 VO - Output Voltage - V VO - Output Voltage - V Figure 12. 10 5.8 Figure 13. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) SLEW RATE vs SUPPLY VOLTAGE SLEW RATE vs TEMPERATURE 2.5 1.9 2.3 Falling Edge 1.7 1.5 SR - Slew Rate - V/s SR - Slew Rate - V/s 2.1 1.3 Rising Edge 1.1 0.9 0.7 0.5 2 1.9 Falling Edge 1.7 1.5 1.3 Rising Edge 1.1 0.9 RL = 10 k AV = 1 VI = 0.8 VPP for V+ < 2.7 V VI = 2 VPP for V+ > 2.7 V 1.5 RL = 10 k AV = 1 VI = 2 VPP V+ = 2.7 V 0.7 2.5 3 3.5 4 VCC - Supply Voltage - V Figure 14. 4.5 0.5 -40 -20 5 0 20 40 60 80 100 120 140 TA - Free-Air Temperature - C Figure 15. SLEW RATE vs TEMPERATURE CMRR vs FREQUENCY 2.5 SR - Slew Rate - V/s 2.1 1.9 90 70 Falling Edge 1.7 1.5 1.3 Rising Edge 60 50 30 0.9 20 0.7 10 0 20 40 60 80 100 120 140 TA - Free-Air Temperature - C Figure 16. 2.7 V 40 1.1 0.5 -40 -20 5V 80 Gain - dB 2.3 100 RL = 10 k AV = 1 VI = 2 VPP V+ = 5 V VI = V+ /2 RL = 5 k 0 100 Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 1k 10k 100k f - Frequency - Hz Figure 17. Submit Documentation Feedback 1M 11 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) PSRR vs FREQUENCY 100 INPUT VOLTAGE NOISE vs FREQUENCY 220 +PSRR (2.7 V) 90 200 VI - Input Voltage Noise - nV/ Hz -PSRR (2.7 V) 80 Gain - dB 70 60 -PSRR (5 V) +PSRR (5 V) 50 40 30 20 10 0 100 180 160 140 120 100 80 5V 2.7 V 60 40 20 RL = 5 k 1k 10k 100k f - Frequency - Hz Figure 18. 1M 0 10M 10 THD+N - Total Harmonic Distortion + Noise - % THD+N - Total Harmonic Distortion + Noise - % 10 1 5V AV = 10 2.7 V AV = 10 2.7 V AV = 1 0.01 5V AV = 1 0.001 0.0001 10 100 1k 10k f - Frequency - Hz 100k f = 10 kHz RL = 600 5V AV = 10 1 2.7 V AV = 10 0.1 5V AV = 1 0.01 0.001 Submit Documentation Feedback 2.7 V AV = 1 0.01 0.1 1 VO - Output Voltage - VPP Figure 21. Figure 20. 12 10k TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE RL = 600 VO = 1 VPP for V+ = 2.7 V VO = 2.5 VPP for V+ = 5 V 0.1 1k f - Frequency - Hz Figure 19. TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 10 100 10 Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) GAIN AND PHASE MARGIN vs FREQUENCY (TA = -40C, 25C, 125C) 160 140 V+ = 5 V RL = 2 k Phase 120 140 Gain - dB 100 80 -40C Gain 60 80 -40C 25C 60 40 125C 20 -20 40 25C 125C 0 Phase Margin - Deg 120 100 20 0 1k 10k 100k 1M 10M f - Frequency - Hz Figure 22. GAIN AND PHASE MARGIN vs FREQUENCY (RL = 600 , 2 k, 100 k) 140 120 140 Phase 120 100 80 RL = 600 60 RL = 2 k Gain RL = 100 k 80 60 40 RL = 100 k Phase Margin - Deg 100 Gain - dB 160 V+ = 2.7 V Closed-Loop Gain = 60 dB 40 20 RL = 2 k 0 RL = 600 20 0 -20 1k 10k 100k 1M 10M f - Frequency - Hz Figure 23. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 Submit Documentation Feedback 13 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) GAIN AND PHASE MARGIN vs FREQUENCY (RL = 600 , 2 k, 100 k) 160 140 120 V+ = 5 V Closed-Loop Gain = 60 dB Phase 140 Gain - dB 100 80 RL = 600 Gain 60 80 RL = 2 k RL = 100 k 60 40 RL = 100 k 20 40 RL = 2 k RL = 600 0 -20 Phase Margin - Deg 120 100 1k 10k 20 100k f - Frequency - Hz Figure 24. 0 10M 1M GAIN AND PHASE MARGIN vs FREQUENCY (CL = 0 pF, 100 pF, 500 pF, 1000 pF) 140 120 100 Phase V+ = 5 V RL = 600 Closed-Loop Gain = 60 dB CL = 0 pF 100 80 Gain - dB 80 40 CL = 500 pF Gain CL = 1000 pF 60 20 0 40 CL = 0 pF 20 -40 0 CL = 500 pF -20 -60 CL = 1000 pF -40 14 -20 Phase Margin - Deg 60 CL = 100 pF 1k Submit Documentation Feedback 10k 100k f - Frequency - Hz Figure 25. CL = 100 pF 1M 10M -80 Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) 6 Input Input TA = -40C RL = 2 k V+/GND = 2.5 V -0.05 -0.1 0.05 -0.15 0 VI - Input Voltage - V VO - Output Voltage - V 0 0.15 VO - Output Voltage - V 0.05 0.2 0.1 LARGE-SIGNAL NONINVERTING RESPONSE 2 -0.2 -0.05 5 1 4 0 -1 3 2 TA = -40C RL = 2 k V+/GND = 2.5 V 1 -3 0 -4 -1 -5 Output -0.1 0.25 -2 VI - Input Voltage - V 0.25 SMALL-SIGNAL NONINVERTING RESPONSE 0.1 Output -0.25 4 s/div" Figure 26. -2 SMALL-SIGNAL NONINVERTING RESPONSE 0.1 4 s/div" Figure 27. -6 LARGE-SIGNAL NONINVERTING RESPONSE 2 6 Input 0.1 TA = 25C RL = 2 k V+/GND = 2.5 V -0.05 -0.1 0.05 -0.15 0 -0.2 -0.05 VI - Input Voltage - V VO - Output Voltage - V 0 0.15 VO - Output Voltage - V 0.05 0.2 5 1 4 0 3 2 -1 TA = 25C RL = 2 k V+/GND = 2.5 V -2 1 -3 0 -4 -1 VI - Input Voltage - V Input -5 Output Output -0.1 -0.25 4 s/div" Figure 28. -2 4 s/div" -6 Figure 29. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 Submit Documentation Feedback 15 LMV341, LMV342, LMV344 SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 www.ti.com TYPICAL CHARACTERISTICS (continued) 6 LARGE-SIGNAL NONINVERTING RESPONSE 2 TA = 125C RL = 2 k V+/GND = 2.5 V 1 0 4 0 -0.05 -0.1 0.05 -0.15 0 -0.05 VO - Output Voltage - V 0.1 5 VI - Input Voltage - V VO - Output Voltage - V 0.15 0.05 -1 3 2 TA = 125C RL = 2 k V+/GND = 2.5 V -2 1 -3 0 -4 -0.2 -5 -1 Output -0.1 Output -0.25 4 s/div" -2 4 s/div" Figure 31. Figure 30. SMALL-SIGNAL INVERTING RESPONSE 0.1 0.05 TA = -40C RL = 2 k V+/GND = 2.5 V -0.05 -0.1 -0.15 0 -0.2 -0.05 VO - Output Voltage - V VO - Output Voltage - V 0 VI - Input Voltage - V 0.05 0.15 2 Input Input 0.2 5 1 4 0 3 2 -1 TA = -40C RL = 2 k V+/GND = 2.5 V 16 4 s/div" Figure 32. Submit Documentation Feedback -2 1 -3 0 -4 -1 -5 Output -0.1 -6 LARGE-SIGNAL INVERTING RESPONSE 6 0.1 0.25 VI - Input Voltage - V Input Input 0.2 VI - Input Voltage - V 0.25 SMALL-SIGNAL NONINVERTING RESPONSE 0.1 Output -0.25 -2 4 s/div" Figure 33. -6 Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 LMV341, LMV342, LMV344 www.ti.com SLOS447H - SEPTEMBER 2004 - REVISED JUNE 2012 TYPICAL CHARACTERISTICS (continued) SMALL-SIGNAL INVERTING RESPONSE LARGE-SIGNAL INVERTING RESPONSE 6 0.1 0.25 TA = 25C RL = 2 k V+/GND = 2.5 V -0.05 -0.1 0.05 -0.15 0 -0.2 -0.05 VO - Output Voltage - V 5 1 4 0 3 2 -1 TA = 25C RL = 2 k V+/GND = 2.5 V 1 -3 0 -4 -1 -5 Output -0.1 Output -2 -0.25 4 s/div" Figure 34. SMALL-SIGNAL INVERTING RESPONSE 0.25 LARGE-SIGNAL INVERTING RESPONSE 2 6 0.05 5 1 4 0 -0.05 -0.1 0.05 -0.15 0 -0.2 -0.05 VO - Output Voltage - V TA = 125C RL = 2 k V+/GND = 2.5 V VI - Input Voltage - V 0 0.15 -1 3 2 TA = 125C RL = 2 k V+/GND = 2.5 V -2 1 -3 0 -4 -5 -1 Output Output -0.1 -6 Input 0.2 VO - Output Voltage - V 4 s/div" Figure 35. 0.1 Input 0.1 -2 VI - Input Voltage - V VO - Output Voltage - V 0 0.15 VI - Input Voltage - V 0.05 VI - Input Voltage - V Input Input 0.2 0.1 2 -0.25 -6 -2 4 s/div" Figure 36. 4 s/div" Figure 37. Copyright (c) 2004-2012, Texas Instruments Incorporated Product Folder Link(s): LMV341 LMV342 LMV344 Submit Documentation Feedback 17 PACKAGE OPTION ADDENDUM www.ti.com 16-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV341IDBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV341IDBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV341IDCKR ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV341IDCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV341IDCKRG4 ACTIVE SC70 DCK 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDDUR PREVIEW VSSOP DDU 8 3000 TBD LMV342IDE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDGKRG4 ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDGKT PREVIEW VSSOP DGK 8 250 TBD LMV342IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDRE4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV342IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344ID ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IDE4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Call TI Samples (Requires Login) LMV341IDBVR Call TI (3) Call TI Call TI PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 16-Aug-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp LMV344IDG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IDR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IDRE4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IDRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM LMV344IPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com (3) 16-Aug-2012 MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LMV341, LMV344 : * Automotive: LMV341-Q1, LMV344-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device LMV341IDBVR Package Package Pins Type Drawing SPQ SOT-23 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) DBV 6 3000 179.0 B0 (mm) K0 (mm) P1 (mm) 8.4 3.2 3.2 1.4 4.0 W Pin1 (mm) Quadrant 8.0 Q3 LMV341IDCKR SC70 DCK 6 3000 180.0 8.4 2.25 2.4 1.22 4.0 8.0 Q3 LMV342IDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV342IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 LMV344IDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 LMV344IPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV341IDBVR SOT-23 DBV 6 3000 203.0 203.0 35.0 LMV341IDCKR SC70 DCK 6 3000 202.0 201.0 28.0 LMV342IDGKR VSSOP DGK 8 2500 358.0 335.0 35.0 LMV342IDR SOIC D 8 2500 340.5 338.1 20.6 LMV344IDR SOIC D 14 2500 367.0 367.0 38.0 LMV344IPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated