Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. MC68020 MC68EC020 MICROPROCESSORS USER'S MANUAL First Edition Motorola reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Motorola does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and the are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. (c) MOTOROLA INC., 1992 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. PREFACE The M68020 User's Manual describes the capabilities, operation, and programming of the MC68020 32-bit, second-generation, enhanced microprocessor and the MC68EC020 32bit, second-generation, enhanced embedded microprocessor. Throughout this manual, "MC68020/EC020" is used when information applies to both the MC68020 and the MC68EC020. "MC68020" and "MC68EC020" are used when information applies only to the MC68020 or MC68EC020, respectively. Freescale Semiconductor, Inc... For detailed information on the MC68020 and MC68EC020 instruction set, refer to M68000PM/AD, M68000 Family Programmer's Reference Manual. This manual consists of the following sections: Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Appendix A Introduction Processing States Signal Description On-Chip Cache Memory Bus Operation Exception Processing Coprocessor Interface Description Instruction Execution Timing Applications Information Electrical Characteristics Ordering Information and Mechanical Data Interfacing an MC68EC020 to a DMA Device That Supports a Three-Wire Bus Arbitration Protocol NOTE In this manual, assert and negate are used to specify forcing a signal to a particular state. In particular, assertion and assert refer to a signal that is active or true; negation and negate indicate a signal that is inactive or false. These terms are used independently of the voltage level (high or low) that they represent. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com iii 9/29/95 SECTION 1: OVERVIEW Freescale Semiconductor, Inc. UM Rev 1 TABLE OF CONTENTS Paragraph Number Title Page Number Freescale Semiconductor, Inc... Section 1 Introduction 1.1 1.2 1.3 1.4 1.5 1.5.1 1.5.2 1.6 1.7 Features ..................................................................................................1-2 Programming Model ................................................................................1-4 Data Types and Addressing Modes Overview ........................................1-8 Instruction Set Overview ......................................................................... 1-10 Virtual Memory and Virtual Machine Concepts ....................................... 1-10 Virtual Memory .................................................................................... 1-10 Virtual Machine .................................................................................... 1-12 Pipelined Architecture .............................................................................1-12 Cache Memory ........................................................................................1-13 Section 2 Processing States 2.1 2.1.1 2.1.2 2.1.3 2.2 2.3 2.3.1 2.3.2 Privilege Levels ....................................................................................... 2-2 Supervisor Privilege Level ...................................................................2-2 User Privilege Level .............................................................................2-3 Changing Privilege Level ..................................................................... 2-3 Address Space Types .............................................................................2-4 Exception Processing.............................................................................. 2-5 Exception Vectors ................................................................................2-5 Exception Stack Frame .......................................................................2-6 Section 3 Signal Description 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 MOTOROLA Signal Index ............................................................................................3-2 Function Code Signals (FC2-FC0) ......................................................... 3-2 Address Bus (A31-A0, MC68020)(A23-A0, MC68EC020) .................... 3-2 Data Bus (D31-D0) .................................................................................3-2 Transfer Size Signals (SIZ1, SIZ0) .........................................................3-2 Asynchronous Bus Control Signals .........................................................3-4 Interrupt Control Signals..........................................................................3-5 Bus Arbitration Control Signals ............................................................... 3-6 Bus Exception Control Signals ................................................................3-6 Emulator Support Signal .........................................................................3-7 Clock (CLK) ............................................................................................. 3-7 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com vii 9/29/95 SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 TABLE OF CONTENTS (Continued) Paragraph Number 3.12 3.13 Title Page Number Power Supply Connections ..................................................................... 3-7 Signal Summary...................................................................................... 3-8 Freescale Semiconductor, Inc... Section 4 On-Chip Cache Memory 4.1 4.2 4.3 4.3.1 4.3.2 On-Chip Cache Organization and Operation .......................................... 4-1 Cache Reset ........................................................................................... 4-3 Cache Control ......................................................................................... 4-3 Cache Control Register (CACR) .........................................................4-3 Cache Address Register (CAAR) ........................................................ 4-4 Section 5 Bus Operation 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.1.7 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.5 5.2.6 5.2.7 5.3 5.3.1 5.3.2 5.3.3 5.4 5.4.1 5.4.1.1 5.4.1.2 5.4.1.3 5.4.2 5.4.3 5.5 5.5.1 viii Bus Transfer Signals............................................................................... 5-1 Bus Control Signals ............................................................................. 5-2 Address Bus ........................................................................................ 5-3 Address Strobe .................................................................................... 5-3 Data Bus.............................................................................................. 5-3 Data Strobe ......................................................................................... 5-4 Data Buffer Enable .............................................................................. 5-4 Bus Cycle Termination Signals............................................................ 5-4 Data Transfer Mechanism....................................................................... 5-5 Dynamic Bus Sizing ............................................................................ 5-5 Misaligned Operands........................................................................... 5-14 Effects of Dynamic Bus Sizing and Operand Misalignment ................ 5-20 Address, Size, and Data Bus Relationships ........................................ 5-21 Cache Interactions .............................................................................. 5-22 Bus Operation ..................................................................................... 5-24 Synchronous Operation with DSACK1/DSACK0 ............................... 5-24 Data Transfer Cycles ..............................................................................5-25 Read Cycle .......................................................................................... 5-26 Write Cycle .......................................................................................... 5-33 Read-Modify-Write Cycle..................................................................... 5-39 CPU Space Cycles ................................................................................. 5-44 Interrupt Acknowledge Bus Cycles ......................................................5-45 Interrupt Acknowledge Cycle--Terminated Normally ...................... 5-45 Autovector Interrupt Acknowledge Cycle ......................................... 5-48 Spurious Interrupt Cycle .................................................................. 5-48 Breakpoint Acknowledge Cycle ........................................................... 5-50 Coprocessor Communication Cycles .................................................. 5-53 Bus Exception Control Cycles................................................................. 5-53 Bus Errors ........................................................................................... 5-55 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA 9/29/95 SECTION 1: OVERVIEW Freescale Semiconductor, Inc. UM Rev 1 TABLE OF CONTENTS (Continued) Freescale Semiconductor, Inc... Paragraph Number 5.5.2 5.5.3 5.5.4 5.6 5.7 5.7.1 5.7.1.1 5.7.1.2 5.7.1.3 5.7.1.4 5.7.2 5.7.2.1 5.7.2.2 5.7.2.3 5.8 Title Page Number Retry Operation ...................................................................................5-56 Halt Operation......................................................................................5-60 Double Bus Fault ................................................................................. 5-60 Bus Synchronization................................................................................5-62 Bus Arbitration .........................................................................................5-62 MC68020 Bus Arbitration ....................................................................5-63 Bus Request (MC68020) .................................................................5-66 Bus Grant (MC68020) ......................................................................5-66 Bus Grant Acknowledge (MC68020) ...............................................5-66 Bus Arbitration Control (MC68020) ..................................................5-67 MC68EC020 Bus Arbitration ...............................................................5-70 Bus Request (MC68EC020) ............................................................5-71 Bus Grant (MC68EC020) .................................................................5-71 Bus Arbitration Control (MC68EC020) .............................................5-73 Reset Operation ......................................................................................5-76 Section 6 Exception Processing 6.1 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 6.1.6 6.1.7 6.1.8 6.1.9 6.1.10 6.1.11 6.1.12 6.2 6.2.1 6.2.2 6.2.3 6.3 6.4 MOTOROLA Exception Processing Sequence ............................................................6-1 Reset Exception...................................................................................6-4 Bus Error Exception .............................................................................6-4 Address Error Exception...................................................................... 6-6 Instruction Trap Exception ...................................................................6-6 Illegal Instruction and Unimplemented Instruction Exceptions ............ 6-7 Privilege Violation Exception ............................................................... 6-8 Trace Exception ...................................................................................6-9 Format Error Exception .......................................................................6-10 Interrupt Exceptions .............................................................................6-11 Breakpoint Instruction Exception ......................................................... 6-17 Multiple Exceptions..............................................................................6-17 Return from Exception .........................................................................6-19 Bus Fault Recovery .................................................................................6-21 Special Status Word (SSW).................................................................6-21 Using Software to Complete the Bus Cycles .......................................6-23 Completing the Bus Cycles with RTE ..................................................6-24 Coprocessor Considerations ...................................................................6-25 Exception Stack Frame Formats .............................................................6-25 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com ix 9/29/95 SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 TABLE OF CONTENTS (Continued) Paragraph Number Title Page Number Freescale Semiconductor, Inc... Section 7 Coprocessor Interface Description 7.1 7.1.1 7.1.2 7.1.3 7.1.4 7.1.4.1 7.1.4.2 7.1.4.3 7.2 7.2.1 7.2.1.1 7.2.1.2 7.2.2 7.2.2.1 7.2.2.1.1 7.2.2.1.2 7.2.2.2 7.2.2.2.1 7.2.2.2.2 7.2.2.3 7.2.2.3.1 7.2.2.3.2 7.2.2.4 7.2.2.4.1 7.2.2.4.2 7.2.3 7.2.3.1 7.2.3.2 7.2.3.2.1 7.2.3.2.2 7.2.3.2.3 7.2.3.2.4 7.2.3.3 7.2.3.3.1 7.2.3.3.2 7.2.3.4 7.2.3.4.1 7.2.3.4.2 7.3 x Introduction .............................................................................................7-1 Interface Features ............................................................................... 7-2 Concurrent Operation Support ............................................................7-2 Coprocessor Instruction Format .......................................................... 7-3 Coprocessor System Interface ............................................................ 7-4 Coprocessor Classification .............................................................. 7-4 Processor-Coprocessor Interface .................................................... 7-5 Coprocessor Interface Register Selection .......................................7-6 Coprocessor Instruction Types ...............................................................7-7 Coprocessor General Instructions ....................................................... 7-8 Format ............................................................................................. 7-8 Protocol............................................................................................ 7-9 Coprocessor Conditional Instructions.................................................. 7-10 Branch on Coprocessor Condition Instruction .................................7-12 Format .......................................................................................... 7-12 Protocol ........................................................................................ 7-12 Set on Coprocessor Condition Instruction .......................................7-13 Format .......................................................................................... 7-13 Protocol ........................................................................................ 7-14 Test Coprocessor Condition, Decrement, and Branch Instruction ... 7-14 Format .......................................................................................... 7-14 Protocol ........................................................................................ 7-15 Trap on Coprocessor Condition Instruction ..................................... 7-15 Format .......................................................................................... 7-15 Protocol ........................................................................................ 7-16 Coprocessor Context Save and Restore Instructions ......................... 7-16 Coprocessor Internal State Frames ................................................. 7-17 Coprocessor Format Words............................................................. 7-18 Empty/Reset Format Word ........................................................... 7-18 Not-Ready Format Word ..............................................................7-19 Invalid Format Word ..................................................................... 7-19 Valid Format Word ....................................................................... 7-20 Coprocessor Context Save Instruction ............................................ 7-20 Format .......................................................................................... 7-20 Protocol ........................................................................................ 7-21 Coprocessor Context Restore Instruction ........................................ 7-22 Format .......................................................................................... 7-22 Protocol ........................................................................................ 7-23 Coprocessor Interface Register Set ........................................................ 7-24 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA 9/29/95 SECTION 1: OVERVIEW Freescale Semiconductor, Inc. UM Rev 1 TABLE OF CONTENTS (Continued) Freescale Semiconductor, Inc... Paragraph Number 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.3.6 7.3.7 7.3.8 7.3.9 7.3.10 7.3.11 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.4.6 7.4.7 7.4.8 7.4.9 7.4.10 7.4.11 7.4.12 7.4.13 7.4.14 7.4.15 7.4.16 7.4.17 7.4.18 7.4.19 7.4.20 7.5 7.5.1 7.5.1.1 7.5.1.2 7.5.1.3 7.5.1.4 7.5.1.5 7.5.2 7.5.2.1 7.5.2.2 MOTOROLA Title Page Number Response CIR ..................................................................................... 7-24 Control CIR .......................................................................................... 7-24 Save CIR ............................................................................................. 7-25 Restore CIR .........................................................................................7-25 Operation Word CIR ............................................................................7-25 Command CIR .....................................................................................7-25 Condition CIR ......................................................................................7-26 Operand CIR ....................................................................................... 7-26 Register Select CIR .............................................................................7-27 Instruction Address CIR .......................................................................7-27 Operand Address CIR .........................................................................7-27 Coprocessor Response Primitives ..........................................................7-27 ScanPC ...............................................................................................7-28 Coprocessor Response Primitive General Format .............................. 7-28 Busy Primitive ......................................................................................7-30 Null Primitive ........................................................................................ 7-31 Supervisor Check Primitive .................................................................7-33 Transfer Operation Word Primitive ......................................................7-33 Transfer from Instruction Stream Primitive ..........................................7-34 Evaluate and Transfer Effective Address Primitive ............................. 7-35 Evaluate Effective Address and Transfer Data Primitive ..................... 7-35 Write to Previously Evaluated Effective Address Primitive .................. 7-37 Take Address and Transfer Data Primitive..........................................7-39 Transfer to/from Top of Stack Primitive ...............................................7-40 Transfer Single Main Processor Register Primitive ............................. 7-40 Transfer Main Processor Control Register Primitive ........................... 7-41 Transfer Multiple Main Processor Registers Primitive ......................... 7-42 Transfer Multiple Coprocessor Registers Primitive .............................7-42 Transfer Status Register and ScanPC Primitive.................................. 7-44 Take Preinstruction Exception Primitive ..............................................7-45 Take Midinstruction Exception Primitive ..............................................7-47 Take Postinstruction Exception Primitive ............................................7-48 Exceptions ...............................................................................................7-49 Coprocessor-Detected Exceptions ...................................................... 7-49 Coprocessor-Detected Protocol Violations ......................................7-50 Coprocessor-Detected Illegal Command or Condition Words ......... 7-51 Coprocessor Data-Processing-Related Exceptions .........................7-51 Coprocessor System-Related Exceptions .......................................7-51 Format Errors ...................................................................................7-52 Main-Processor-Detected Exceptions ................................................. 7-52 Protocol Violations ........................................................................... 7-52 F-Line Emulator Exceptions .............................................................7-54 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com xi 9/29/95 SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 TABLE OF CONTENTS (Continued) Paragraph Number Freescale Semiconductor, Inc... 7.5.2.3 7.5.2.4 7.5.2.5 7.5.2.6 7.5.2.7 7.5.2.8 7.5.3 7.6 Title Page Number Privilege Violations........................................................................... 7-55 cpTRAPcc Instruction Traps ............................................................ 7-55 Trace Exceptions ............................................................................. 7-55 Interrupts ..........................................................................................7-56 Format Errors ................................................................................... 7-57 Address and Bus Errors................................................................... 7-57 Coprocessor Reset ..............................................................................7-58 Coprocessor Summary ........................................................................... 7-58 Section 8 Instruction Execution Timing 8.1 8.1.1 8.1.2 8.1.3 8.1.4 8.1.5 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.2.6 8.2.7 8.2.8 8.2.9 8.2.10 8.2.11 8.2.12 8.2.13 8.2.14 8.2.15 8.2.16 8.2.17 8.2.18 Timing Estimation Factors ...................................................................... 8-1 Instruction Cache and Prefetch ........................................................... 8-1 Operand Misalignment ........................................................................ 8-2 Bus/Sequencer Concurrency............................................................... 8-2 Instruction Execution Overlap ............................................................. 8-3 Instruction Stream Timing Examples ...................................................8-4 Instruction Timing Tables ........................................................................ 8-9 Fetch Effective Address ...................................................................... 8-13 Fetch Immediate Effective Address..................................................... 8-14 Calculate Effective Address ................................................................ 8-16 Calculate Immediate Effective Address............................................... 8-17 Jump Effective Address....................................................................... 8-19 MOVE Instruction ................................................................................ 8-20 Special-Purpose MOVE Instruction ..................................................... 8-29 Arithmetic/Logical Instructions............................................................. 8-30 Immediate Arithmetic/Logical Instructions ........................................... 8-31 Binary-Coded Decimal Operations ...................................................... 8-32 Single-Operand Instructions ................................................................ 8-33 Shift/Rotate Instructions ...................................................................... 8-34 Bit Manipulation Instructions ............................................................... 8-35 Bit Field Manipulation Instructions....................................................... 8-36 Conditional Branch Instructions........................................................... 8-37 Control Instructions..............................................................................8-38 Exception-Related Instructions ............................................................8-39 Save and Restore Operations ............................................................. 8-40 Section 9 Applications Information 9.1 9.2 9.3 xii Floating-Point Units .................................................................................9-1 Byte Select Logic for the MC68020/EC020............................................. 9-5 Power and Ground Considerations ......................................................... 9-9 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA 9/29/95 SECTION 1: OVERVIEW Freescale Semiconductor, Inc. UM Rev 1 TABLE OF CONTENTS (Concluded) Freescale Semiconductor, Inc... Paragraph Number 9.4 9.5 9.6 9.7 9.7.1 9.7.2 9.8 9.8.1 9.8.2 Title Page Number Clock Driver............................................................................................. 9-10 Memory Interface .................................................................................... 9-11 Access Time Calculations .......................................................................9-12 Module Support .......................................................................................9-14 Module Descriptor................................................................................9-14 Module Stack Frame ........................................................................... 9-16 Access Levels .........................................................................................9-17 Module Call.......................................................................................... 9-18 Module Return ..................................................................................... 9-19 Section 10 Electrical Characteristics 10.1 10.2 10.2.1 10.2.2 10.3 Maximum Ratings ................................................................................. 10-1 Thermal Considerations ........................................................................ 10-1 MC68020 Thermal Characteristics and DC Electrical Characteristics ...........................................................10-2 MC68EC020 Thermal Characteristics and DC Electrical Characteristics ...........................................................10-4 AC Electrical Characteristics ................................................................. 10-5 Section 11 Ordering Information and Mechanical Data 11.1 11.1.1 11.1.2 11.2 11.2.1 11.2.2 11.2.3 11.2.4 11.2.5 11.2.6 11.2.7 11.2.8 11.2.9 11.2.10 Standard Ordering Information.............................................................. 11-1 Standard MC68020 Ordering Information..........................................11-1 Standard MC68EC020 Ordering Information .................................... 11-1 Pin Assignments and Package Dimensions .......................................... 11-2 MC68020 RC and RP Suffix--Pin Assignment .................................11-2 MC68020 RC Suffix--Package Dimensions ..................................... 11-3 MC68020 RP Suffix--Package Dimensions...................................... 11-4 MC68020 FC and FE Suffix--Pin Assignment .................................. 11-5 MC68020 FC Suffix--Package Dimensions ...................................... 11-6 MC68020 FE Suffix--Package Dimensions ......................................11-7 MC68EC020 RP Suffix--Pin Assignment..........................................11-8 MC68EC020 RP Suffix--Package Dimensions .................................11-9 MC68EC020 FG Suffix--Pin Assignment..........................................11-10 MC68EC020 FG Suffix--Package Dimensions .................................11-11 Appendix A Interfacing an MC68EC020 to a DMA Device That Supports a Three-Wire Bus Arbitration Protocol MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com xiii SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 9/29/95 LIST OF ILLUSTRATIONS Freescale Semiconductor, Inc... Figure Number Title Page Number 1-1 1-2 1-3 1-4 1-5 MC68020/EC020 Block Diagram ..................................................................... 1-3 User Programming Model ................................................................................ 1-5 Supervisor Programming Model Supplement .................................................. 1-6 Status Register (SR) ........................................................................................ 1-7 Instruction Pipe ................................................................................................1-13 2-1 General Exception Stack Frame ...................................................................... 2-6 3-1 Functional Signal Groups .................................................................................3-1 4-1 4-2 4-3 MC68020/EC020 On-Chip Cache Organization .............................................. 4-2 Cache Control Register ....................................................................................4-3 Cache Address Register .................................................................................. 4-4 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 Relationship between External and Internal Signals........................................ 5-2 Input Sample Window ...................................................................................... 5-2 Internal Operand Representation .....................................................................5-6 MC68020/EC020 Interface to Various Port Sizes ............................................ 5-6 Long-Word Operand Write to Word Port Example........................................... 5-10 Long-Word Operand Write to Word Port Timing .............................................. 5-11 Word Operand Write to Byte Port Example ..................................................... 5-12 Word Operand Write to Byte Port Timing......................................................... 5-13 Misaligned Long-Word Operand Write to Word Port Example ........................ 5-14 Misaligned Long-Word Operand Write to Word Port Timing............................ 5-15 Misaligned Long-Word Operand Read from Word Port Example .................... 5-16 Misaligned Word Operand Write to Word Port Example.................................. 5-16 Misaligned Word Operand Write to Word Port Timing ..................................... 5-17 Misaligned Word Operand Read from Word Bus Example .............................. 5-18 Misaligned Long-Word Operand Write to Long-Word Port Example ............... 5-18 Misaligned Long-Word Operand Write to Long-Word Port Timing .................. 5-19 Misaligned Long-Word Operand Read from Long-Word Port Example ........... 5-20 Byte Enable Signal Generation for 16- and 32-Bit Ports.................................. 5-23 Long-Word Read Cycle Flowchart ................................................................... 5-26 Byte Read Cycle Flowchart ..............................................................................5-27 Byte and Word Read Cycles--32-Bit Port ....................................................... 5-28 Long-Word Read--8-Bit Port ........................................................................... 5-29 Long-Word Read--16- and 32-Bit Ports .......................................................... 5-30 xiv M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA SECTION 1: OVERVIEW Freescale Semiconductor, Inc. 9/29/95 UM Rev 1 LIST OF ILLUSTRATIONS (Continued) Freescale Semiconductor, Inc... Figure Number Title Page Number 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 5-35 5-36 5-37 5-38 5-39 5-40 5-41 5-42 5-43 5-44 5-45 5-46 5-47 5-48 5-49 5-50 5-51 5-52 Write Cycle Flowchart ......................................................................................5-33 Read-Write-Read Cycles--32-Bit Port .............................................................5-34 Byte and Word Write Cycles--32-Bit Port ........................................................5-35 Long-Word Operand Write--8-Bit Port ............................................................5-36 Long-Word Operand Write--16-Bit Port...........................................................5-37 Read-Modify-Write Cycle Flowchart .................................................................5-40 Byte Read-Modify-Write Cycle--32-Bit Port (TAS Instruction) ........................ 5-41 MC68020/EC020 CPU Space Address Encoding ............................................5-45 Interrupt Acknowledge Cycle Flowchart ...........................................................5-46 Interrupt Acknowledge Cycle Timing................................................................ 5-47 Autovector Operation Timing ...........................................................................5-49 Breakpoint Acknowledge Cycle Flowchart .......................................................5-50 Breakpoint Acknowledge Cycle Timing ............................................................5-51 Breakpoint Acknowledge Cycle Timing (Exception Signaled) .......................... 5-52 Bus Error without DSACK1/DSACK0 ............................................................. 5-57 Late Bus Error with DSACK1/DSACK0 .......................................................... 5-58 Late Retry.........................................................................................................5-59 Halt Operation Timing ......................................................................................5-61 MC68020 Bus Arbitration Flowchart for Single Request .................................. 5-64 MC68020 Bus Arbitration Operation Timing for Single Request ...................... 5-65 MC68020 Bus Arbitration State Diagram ......................................................... 5-67 MC68020 Bus Arbitration Operation Timing--Bus Inactive ............................. 5-69 MC68EC020 Bus Arbitration Flowchart for Single Request ............................. 5-71 MC68EC020 Bus Arbitration Operation Timing for Single Request ................. 5-72 MC68EC020 Bus Arbitration State Diagram ....................................................5-73 MC68EC020 Bus Arbitration Operation Timing--Bus Inactive ........................ 5-75 Interface for Three-Wire to Two-Wire Bus Arbitration ......................................5-76 Initial Reset Operation Timing ..........................................................................5-77 RESET Instruction Timing ................................................................................5-78 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 Reset Operation Flowchart ..............................................................................6-5 Interrupt Pending Procedure ............................................................................6-12 Interrupt Recognition Examples .......................................................................6-13 Assertion of IPEND (MC68020 Only) ...............................................................6-14 Interrupt Exception Processing Flowchart ........................................................6-15 Breakpoint Instruction Flowchart ......................................................................6-18 RTE Instruction for Throwaway Four-Word Frame .......................................... 6-20 Special Status Word Format ............................................................................ 6-22 7-1 7-2 7-3 F-Line Coprocessor Instruction Operation Word.............................................. 7-3 Asynchronous Non-DMA M68000 Coprocessor Interface Signal Usage ......... 7-5 MC68020/EC020 CPU Space Address Encodings ..........................................7-6 MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com xv SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 9/29/95 LIST OF ILLUSTRATIONS (Continued) Freescale Semiconductor, Inc... Figure Number 7-4 7-5 7-6 7-7 7-8 7-9 7-10 7-11 7-12 7-13 7-14 7-15 7-16 7-17 7-18 7-19 7-20 7-21 7-22 7-23 7-24 7-25 7-26 7-27 7-28 7-29 7-30 7-31 7-32 7-33 7-34 7-35 7-36 7-37 7-38 7-39 7-40 7-41 7-42 7-43 7-44 xvi Title Page Number Coprocessor Address Map in MC68020/EC020 CPU Space .......................... 7-7 Coprocessor Interface Register Set Map ......................................................... 7-7 Coprocessor General Instruction Format (cpGEN) .......................................... 7-8 Coprocessor Interface Protocol for General Category Instructions.................. 7-10 Coprocessor Interface Protocol for Conditional Category Instructions ............ 7-11 Branch on Coprocessor Condition Instruction Format (cpBcc.W) ................... 7-12 Branch on Coprocessor Condition Instruction Format (cpBcc.L) ..................... 7-12 Set on Coprocessor Condition Instruction Format (cpScc) .............................. 7-13 Test Coprocessor Condition, Decrement, and Branch Instruction Format (cpDBcc)........................................................................... 7-14 Trap on Coprocessor Condition Instruction Format (cpTRAPcc) ..................... 7-15 Coprocessor State Frame Format in Memory ..................................................7-17 Coprocessor Context Save Instruction Format (cpSAVE) ............................... 7-20 Coprocessor Context Save Instruction Protocol .............................................. 7-21 Coprocessor Context Restore Instruction Format (cpRESTORE) ................... 7-22 Coprocessor Context Restore Instruction Protocol .......................................... 7-23 Control CIR Format ..........................................................................................7-25 Condition CIR Format ......................................................................................7-26 Operand Alignment for Operand CIR Accesses .............................................. 7-26 Coprocessor Response Primitive Format ........................................................ 7-28 Busy Primitive Format ...................................................................................... 7-30 Null Primitive Format........................................................................................ 7-31 Supervisor Check Primitive Format.................................................................. 7-33 Transfer Operation Word Primitive Format ...................................................... 7-33 Transfer from Instruction Stream Primitive Format .......................................... 7-34 Evaluate and Transfer Effective Address Primitive Format.............................. 7-35 Evaluate Effective Address and Transfer Data Primitive Format ..................... 7-35 Write to Previously Evaluated Effective Address Primitive Format .................. 7-37 Take Address and Transfer Data Primitive Format ..........................................7-39 Transfer to/from Top of Stack Primitive Format ............................................... 7-40 Transfer Single Main Processor Register Primitive Format ............................. 7-40 Transfer Main Processor Control Register Primitive Format ........................... 7-41 Transfer Multiple Main Processor Registers Primitive Format ......................... 7-42 Register Select Mask Format ...........................................................................7-42 Transfer Multiple Coprocessor Registers Primitive Format.............................. 7-43 Operand Format in Memory for Transfer to -(An) ........................................... 7-44 Transfer Status Register and ScanPC Primitive Format.................................. 7-44 Take Preinstruction Exception Primitive Format .............................................. 7-45 MC68020/EC020 Preinstruction Stack Frame ................................................. 7-46 Take Midinstruction Exception Primitive Format .............................................. 7-47 MC68020/EC020 Midinstruction Stack Frame ................................................. 7-47 Take Postinstruction Exception Primitive Format............................................. 7-48 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA SECTION 1: OVERVIEW Freescale Semiconductor, Inc. 9/29/95 UM Rev 1 LIST OF ILLUSTRATIONS (Concluded) Freescale Semiconductor, Inc... Figure Number Title Page Number 7-45 MC68020/EC020 Postinstruction Stack Frame................................................ 7-48 8-1 8-2 8-3 8-4 8-5 8-6 Concurrent Instruction Execution ..................................................................... 8-3 Instruction Execution for Instruction Timing Purposes ..................................... 8-3 Processor Activity for Example 1 .....................................................................8-5 Processor Activity for Example 2 .....................................................................8-6 Processor Activity for Example 3 .....................................................................8-7 Processor Activity for Example 4 .....................................................................8-8 9-1 9-2 9-3 9-4 9-5 9-6 9-7 9-8 9-9 9-10 9-11 9-12 9-13 32-Bit Data Bus Coprocessor Connection........................................................9-2 Chip Select Generation PAL ............................................................................ 9-3 Chip Select PAL Equations .............................................................................. 9-4 Bus Cycle Timing Diagram ...............................................................................9-4 Example MC68020/EC020 Byte Select PAL System Configuration ................ 9-7 MC68020/EC020 Byte Select PAL Equations ..................................................9-8 High-Resolution Clock Controller ..................................................................... 9-11 Alternate Clock Solution ...................................................................................9-11 Access Time Computation Diagram .................................................................9-12 Module Descriptor Format ................................................................................9-15 Module Entry Word ..........................................................................................9-15 Module Call Stack Frame .................................................................................9-16 Access Level Control Bus Registers ................................................................9-17 10-1 10-2 10-3 10-4 10-5 Drive Levels and Test Points for AC Specifications ....................................... 10-6 Clock Input Timing Diagram ........................................................................... 10-7 Read Cycle Timing Diagram ..........................................................................10-11 Write Cycle Timing Diagram........................................................................... 10-12 Bus Arbitration Timing Diagram .....................................................................10-13 A-1 Bus Arbitration Circuit--MC68EC020 (Two-Wire) to DMA (Three-Wire) ......... A-1 MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com xvii SECTION 1:Semiconductor, OVERVIEW Freescale Inc. UM Rev.1.0 9/29/95 LIST OF TABLES Freescale Semiconductor, Inc... Table Number Title Page Number 1-1 1-2 Addressing Modes ........................................................................................... 1-9 Instruction Set ..................................................................................................1-11 2-1 Address Space Encodings ............................................................................... 2-4 3-1 3-2 Signal Index ..................................................................................................... 3-3 Signal Summary............................................................................................... 3-8 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 DSACK1/DSACK0 Encodings and Results .................................................... 5-5 SIZ1, SIZ0 Signal Encoding ............................................................................. 5-7 Address Offset Encodings ............................................................................... 5-7 Data Bus Requirements for Read Cycles ........................................................ 5-8 MC68020/EC020 Internal to External Data Bus Multiplexer-- Write Cycles ...................................................................................................5-9 Memory Alignment and Port Size Influence on Read/Write Bus Cycles .......... 5-20 Data Bus Byte Enable Signals for Byte, Word, and Long-Word Ports ............. 5-22 DSACK1/DSACK0, BERR, HALT Assertion Results ..................................... 5-54 6-1 6-2 6-3 6-4 6-5 Exception Vector Assignments ........................................................................6-3 Tracing Control ................................................................................................ 6-9 Interrupt Levels and Mask Values.................................................................... 6-12 Exception Priority Groups ................................................................................ 6-18 Exception Stack Frames .................................................................................. 6-26 7-1 7-2 7-3 7-4 7-5 7-6 cpTRAPcc Opmode Encodings........................................................................ 7-16 Coprocessor Format Word Encodings ............................................................. 7-18 Null Coprocessor Response Primitive Encodings............................................ 7-32 Valid Effective Address Field Codes ................................................................ 7-36 Main Processor Control Register Select Codes............................................... 7-41 Exceptions Related to Primitive Processing .................................................... 7-53 8-1 8-2 8-3 Examples 1-4 Instruction Stream Execution Comparison ............................... 8-8 Instruction Timings from Timing Tables ........................................................... 8-11 Observed Instruction Timings .......................................................................... 8-11 xviii M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA SECTION 1: OVERVIEW Freescale Semiconductor, Inc. 9/29/95 UM Rev 1 LIST OF TABLES (Continued) Table Number Freescale Semiconductor, Inc... 9-1 9-2 9-3 9-4 9-5 Title Page Number 9-6 Data Bus Activity for Byte, Word, and Long-Word Ports .................................. 9-6 VCC and GND Pin Assignments--MC68EC020 PPGA (RP Suffix) .................9-10 VCC and GND Pin Assignments--MC68EC020 PQFP (FG Sufffix)................. 9-10 Memory Access Time Equations at 16.67 and 25 MHz ...................................9-13 Calculated tAVDV Values for Operation at Frequencies Less Than or Equal to the CPU Maximum Frequency Rating........................ 9-14 Access Status Register Codes......................................................................... 9-18 10-1 10-2 10-3 10-4 JA vs. Airflow--MC68020 CQFP Package ...................................................10-3 Power vs. Rated Frequency (at TJ Maximum = 110C) ................................. 10-3 Temperature Rise of Board vs. PD--MC68020 CQFP Package ................... 10-3 JA vs. Airflow--MC68EC020 PQFP Package .............................................. 10-4 MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com xix Freescale Semiconductor, Inc. MC68020/EC020 ACRONYM LIST Freescale Semiconductor, Inc... BCD CAAR CACR CCR CIR CMOS CPU CQFP DDMA DFC DMA DRAM FPCP HCMOS IEEE ISP LMB LRAR LSB MMU MPU MSB MSP NMOS PAL PC PGA PMMU PPGA PQFP RAM SFC SP SR SSP SSW UMB USP VBR VLSI MOTOROLA -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Binary-Coded Decimal Cache Address Register Cache Control Register Condition Code Register Coprocessor Interface Register Complementary Metal Oxide Semiconductor Central Processing Unit Ceramic Quad Flat Pack Dual-Channel Direct Memory Access Destination Function Code Register Direct Memory Access Dynamic Random Access Memory Floating-Point Coprocessor High-Density Complementary Metal Oxide Semiconductor Institute of Electrical and Electronic Engineers Interrupt Stack Pointer Lower Middle Byte Limited Rate Auto Request Least Significant Byte Memory Management Unit Microprocessor Unit Most Significant Byte Master Stack Pointer n-Type Metal Oxide Semiconductor Programmable Array Logic Program Counter Pin Grid Array Paged Memory Management Unit Plastic Pin Grid Array Plastic Quad Flat Pack Random Access Memory Source Function Code Register Stack Pointer Status Register Supervisor Stack Pointer Special Status Word Upper Middle Byte User Stack Pointer Vector Base Register Very Large Scale Integration M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com v Freescale Semiconductor, Inc. SECTION 1 INTRODUCTION Freescale Semiconductor, Inc... The MC68020 is the first full 32-bit implementation of the M68000 family of microprocessors from Motorola. Using VLSI technology, the MC68020 is implemented with 32-bit registers and data paths, 32-bit addresses, a rich instruction set, and versatile addressing modes. The MC68020 is object-code compatible with earlier members of the M68000 family and has the added features of new addressing modes in support of high-level languages, an on-chip instruction cache, and a flexible coprocessor interface with full IEEE floating-point support (the MC68881 and MC68882). The internal operations of this microprocessor operate in parallel, allowing multiple instructions to be executed concurrently. The asynchronous bus structure of the MC68020 uses a nonmultiplexed bus with 32 bits of address and 32 bits of data. The processor supports a dynamic bus sizing mechanism that allows the processor to transfer operands to or from external devices while automatically determining device port size on a cycle-by-cycle basis. The dynamic bus interface allows access to devices of differing data bus widths, in addition to eliminating all data alignment restrictions. The MC68EC020 is an economical high-performance embedded microprocessor based on the MC68020 and has been designed specifically to suit the needs of the embedded microprocessor market. The major differences in the MC68EC020 and the MC68020 are that the MC68EC020 has a 24-bit address bus and does not implement the following signals: ECS , OCS, DBEN, IPEND , and BGACK . Also, the available packages and frequencies differ for the MC68020 and MC68EC020 (see Section 11 Ordering Information and Mechanical Data.) Unless otherwise stated, information in this manual applies to both the MC68020 and the MC68EC020. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-1 Freescale Semiconductor, Inc. 1.1 FEATURES The main features of the MC68020/EC020 are as follows: * Object-Code Compatible with Earlier M68000 Microprocessors * Addressing Mode Extensions for Enhanced Support of High-Level Languages * New Bit Field Data Type Accelerates Bit-Oriented Applications--e.g., Video Graphics * An On-Chip Instruction Cache for Faster Instruction Execution Freescale Semiconductor, Inc... * Coprocessor Interface to Companion 32-Bit Peripherals--the MC68881 and MC68882 Floating-Point Coprocessors and the MC68851 Paged Memory Management Unit * Pipelined Architecture with High Degree of Internal Parallelism Allowing Multiple Instructions To Be Executed Concurrently * High-Performance Asynchronous Bus Is Nonmultiplexed and Full 32 Bits * Dynamic Bus Sizing Efficiently Supports 8-/16-/32-Bit Memories and Peripherals * Full Support of Virtual Memory and Virtual Machine * Sixteen 32-Bit General-Purpose Data and Address Registers * Two 32-Bit Supervisor Stack Pointers and Five Special-Purpose Control Registers * Eighteen Addressing Modes and Seven Data Types * 4-Gbyte Direct Addressing Range for the MC68020 * 16-Mbyte Direct Addressing Range for the MC68EC020 * Selection of Processor Speeds for the MC68020: 16.67, 20, 25, and 33.33 MHz * Selection of Processor Speeds for the MCEC68020: 16.67 and 25 MHz A block diagram of the MC68020/EC020 is shown in Figure 1-1. 1-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SEQUENCER AND CONTROL INSTRUCTION PIPE Freescale Semiconductor, Inc... CONTROL STORE STAGE D STAGE C STAGE B CACHE HOLDING REGISTER (CAHR) CONTROL LOGIC INTERNAL DATA BUS INSTRUCTION CACHE ADDRESS BUS INSTRUCTION ADDRESS BUS 32-BIT DATA PADS EXECUTION UNIT DATA BUS * 32-BIT PROGRAM COUNTER SECTION ADDRESS PADS ADDRESS SECTION DATA SECTION SIZE MULTIPLEXER ADDRESS BUS MISALIGNMENT MULTIPLEXER BUS CONTROLLER WRITE PENDING BUFFER PREFETCH PENDING BUFFER MICROBUS CONTROL LOGIC BUS CONTROL SIGNALS * 24-Bit for MC68EC020 Figure 1-1. MC68020/EC020 Block Diagram MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-3 Freescale Semiconductor, Inc. 1.2 PROGRAMMING MODEL The programming model of the MC68020/EC020 consists of two groups of registers, the user model and the supervisor model, that correspond to the user and supervisor privilege levels, respectively. User programs executing at the user privilege level use the registers of the user model. System software executing at the supervisor level uses the control registers of the supervisor level to perform supervisor functions. Freescale Semiconductor, Inc... As shown in the programming models (see Figures 1-2 and 1-3), the MC68020/EC020 has 16 32-bit general-purpose registers, a 32-bit PC two 32-bit SSPs, a 16-bit SR, a 32-bit VBR, two 3-bit alternate function code registers, and two 32-bit cache handling (address and control) registers. The user programming model remains unchanged from earlier M68000 family microprocessors. The supervisor programming model supplements the user programming model and is used exclusively by MC68020/EC020 system programmers who utilize the supervisor privilege level to implement sensitive operating system functions. The supervisor programming model contains all the controls to access and enable the special features of the MC68020/EC020. All application software, written to run at the nonprivileged user level, migrates to the MC68020/EC020 from any M68000 platform without modification. Registers D7-D0 are data registers used for bit and bit field (1 to 32 bits), byte (8 bit), word (16 bit), long-word (32 bit), and quad-word (64 bit) operations. Registers A6-A0 and the USP, ISP, and MSP are address registers that may be used as software stack pointers or base address registers. Register A7 (shown as A7 in Figure 1-2 and as A7 and A7 in Figure 1-3) is a register designation that applies to the USP in the user privilege level and to either the ISP or MSP in the supervisor privilege level. In the supervisor privilege level, the active stack pointer (interrupt or master) is called the SSP. In addition, the address registers may be used for word and long-word operations. All of the 16 general-purpose registers (D7-D0, A7-A0) may be used as index registers. The PC contains the address of the next instruction to be executed by the MC68020/EC020. During instruction execution and exception processing, the processor automatically increments the contents of the PC or places a new value in the PC, as appropriate. 1-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 31 16 15 8 7 0 D0 D1 Freescale Semiconductor, Inc... D2 D3 D4 DATA REGISTERS D5 D6 D7 31 16 15 0 A0 A1 A2 A3 ADDRESS REGISTERS A4 A5 A6 31 16 15 0 31 A7 (USP) USER STACK POINTER PC PROGRAM COUNTER CCR CONDITION CODE REGISTER 0 15 8 7 0 0 Figure 1-2. User Programming Model MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-5 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. 31 31 16 15 0 16 15 15 A7' (ISP) INTERRUPT STACK POINTER A7'' (MSP) MASTER STACK POINTER SR STATUS REGISTER VBR VECTOR BASE REGISTER 0 8 7 0 (CCR) 31 0 31 3 2 0 SFC DFC 31 ALTERNATE FUNCTION CODE REGISTERS 0 31 CACR CACHE CONTROL REGISTER CAAR CACHE ADDRESS REGISTER 0 Figure 1-3. Supervisor Programming Model Supplement 1-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The SR (see Figure 1-4) stores the processor status. It contains the condition codes that reflect the results of a previous operation and can be used for conditional instruction execution in a program. The condition codes are extend (X), negative (N), zero (Z), overflow (V), and carry (C). The user byte, which contains the condition codes, is the only portion of the SR information available in the user privilege level, and it is referenced as the CCR in user programs. In the supervisor privilege level, software can access the entire SR, including the interrupt priority mask (three bits) and control bits that indicate whether the processor is in: 1. One of two trace modes (T1, T0) 2. Supervisor or user privilege level (S) 3. Master or interrupt mode (M) USER BYTE (CONDITION CODE REGISTER) SYSTEM BYTE 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 T1 T0 S M 0 I2 I1 I0 0 0 0 X N Z V C CARRY TRACE ENABLE INTERRUPT PRIORITY MASK OVERFLOW ZERO SUPERVISOR/USER LEVEL NEGATIVE MASTER/INTERRUPT MODE EXTEND Figure 1-4. Status Register (SR) The VBR contains the base address of the exception vector table in memory. The displacement of an exception vector is added to the value in this register to access the vector table. The alternate function code registers, SFC and DFC, contain 3-bit function codes. For the MC68020, function codes can be considered extensions of the 32-bit linear address that optionally provide as many as eight 4-Gbyte address spaces; for the MC68EC020, function codes can be considered extensions of the 24-bit linear address that optionally provide as many as eight 16-Mbyte address spaces. Function codes are automatically generated by the processor to select address spaces for data and program at the user and supervisor privilege levels and to select a CPU address space for processor functions (e.g., coprocessor communications). Registers SFC and DFC are used by certain instructions to explicitly specify the function codes for operations. The CACR controls the on-chip instruction cache of the MC68020/EC020. The CAAR stores an address for cache control functions. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-7 Freescale Semiconductor, Inc. 1.3 DATA TYPES AND ADDRESSING MODES OVERVIEW Freescale Semiconductor, Inc... For detailed information on the data types and addressing modes supported by the MC68020/EC020, refer to M68000PM/AD, M68000 Family Programmer's Reference Manual. The MC68020/EC020 supports seven basic data types: 1. Bits 2. Bit Fields (Fields of consecutive bits, 1-32 bits long) 3. BCD Digits (Packed: 2 digits/byte, Unpacked: 1 digit/byte) 4. Byte Integers (8 bits) 5. Word Integers (16 bits) 6. Long-Word Integers (32 bits) 7. Quad-Word Integers (64 bits) In addition, the MC68020/EC020 instruction set supports operations on other data types such as memory addresses. The coprocessor mechanism allows direct support of floatingpoint operations with the MC68881 and MC68882 floating-point coprocessors as well as specialized user-defined data types and functions. The 18 addressing modes listed in Table 1-1 include nine basic types: 1. Register Direct 2. Register Indirect 3. Register Indirect with Index 4. Memory Indirect 5. PC Indirect with Displacement 6. PC Indirect with Index 7. PC Memory Indirect 8. Absolute 9. Immediate The register indirect addressing modes have postincrement, predecrement, displacement, and index capabilities. The PC modes have index and offset capabilities. Both modes are extended to provide indirect reference through memory. In addition to these addressing modes, many instructions implicitly specify the use of the CCR, stack pointer, and/or PC. 1-8 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 1-1. Addressing Modes Addressing Modes Syntax Register Direct Data Address Dn An Register Indirect Address Address with Postincrement Address with Predecrement Address with Displacement Address Register Indirect with Index 8-Bit Displacement Base Displacement Freescale Semiconductor, Inc... Memory Indirect Postindexed Preindexed (d 8, An, Xn) (bd, An, Xn) ([bd, An], Xn, od) ([bd, An, Xn], od) PC Indirect with Displacement PC Indirect with Index 8-Bit Displacement Base Displacement (d 16 , PC) (d 8, PC, Xn) (bd, PC, Xn) PC Indirect Postindexed Preindexed ([bd, PC], Xn, od) ([bd, PC, Xn], od) Absolute Data Addressing Short Long (xxx).W (xxx).L Immediate # NOTE: Dn = An = d8, d16 = Xn = bd = od = PC () [] MOTOROLA (An) (An)+ -(An) (d 16 , An) = = = = Data Register, D7-D0 Address Register, A7-A0 A twos complement or sign-extended displacement added as part of the effective address calculation; size is 8 (d8) or 16 (d16 ) bits; when omitted, assemblers use a value of zero. Address or data register used as an index register; form is Xn.SIZE *SCALE, where SIZE is .W or .L (indicates index register size) and SCALE is 1, 2, 4, or 8 (index register is multiplied by SCALE); use of SIZE and/or SCALE is optional. A twos-complement base displacement; when present, size can be 16 or 32 bits. Outer displacement added as part of effective address calculation after any memory indirection; use is optional with a size of 16 or 32 bits. Program Counter Immediate value of 8, 16, or 32 bits Effective Address Use as indirect access to long-word address. M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-9 Freescale Semiconductor, Inc. 1.4 INSTRUCTION SET OVERVIEW For detailed information on the MC68020/EC020 instruction set, refer to M68000PM/AD, M68000 Family Programmer's Reference Manual. The instructions in the MC68020/EC020 instruction set are listed in Table 1-2. The instruction set has been tailored to support structured high-level languages and sophisticated operating systems. Many instructions operate on bytes, words, or long words, and most instructions can use any of the 18 addressing modes. Freescale Semiconductor, Inc... 1.5 VIRTUAL MEMORY AND VIRTUAL MACHINE CONCEPTS The full addressing range of the MC68020 is 4 Gbytes (4,294,967,296 bytes) in each of eight address spaces; the full addressing range of the MC68EC020 is 16 Mbytes (16,777,216 bytes) in each of the eight address spaces. Even though most systems implement a smaller physical memory, the system can be made to appear to have a full 4 Gbytes (MC68020) or 16 Mbytes (MC68EC020) of memory available to each user program by using virtual memory techniques. In a virtual memory system, a user program can be written as if it has a large amount of memory available, although the physical memory actually present is much smaller. Similarly, a system can be designed to allow user programs to access devices that are not physically present in the system, such as tape drives, disk drives, printers, terminals, and so forth. With proper software emulation, a physical system can appear to be any other M68000 computer system to a user program, and the program can be given full access to all of the resources of that emulated system. Such an emulated system is called a virtual machine. 1.5.1 Virtual Memory A system that supports virtual memory has a limited amount of high-speed physical memory that can be accessed directly by the processor and maintains an image of a much larger virtual memory on a secondary storage device such as a large-capacity disk drive. When the processor attempts to access a location in the virtual memory map that is not resident in physical memory, a page fault occurs. The access to that location is temporarily suspended while the necessary data is fetched from secondary storage and placed in physical memory. The suspended access is then either restarted or continued. The MC68020/EC020 uses instruction continuation to support virtual memory. When a bus cycle is terminated with a bus error, the microprocessor suspends the current instruction and executes the virtual memory bus error handler. When the bus error handler has completed execution, it returns control to the program that was executing when the error was detected, reruns the faulted bus cycle (when required), and continues the suspended instruction. 1-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Table 1-2. Instruction Set Mnemonic ABCD ADD ADDA ADDI ADDQ ADDX AND ANDI ASL, ASR Bcc BCHG BCLR BFCHG BFCLR BFEXTS BFEXTU BFFFO BFINS BFSET BFTST BKPT BRA BSET BSR BTST CALLM CAS CAS2 CHK CHK2 CLR CMP CMPA CMPI CMPM CMP2 DBcc DIVS, DIVSL DIVU, DIVUL EOR EORI EXG EXT, EXTB ILLEGAL JMP JSR LEA LINK LSL, LSR MOVE MOVEA MOVE CCR MOVE SR MOTOROLA Description Add Decimal with Extend Add Add Address Add Immediate Add Quick Add with Extend Logical AND Logical AND Immediate Arithmetic Shift Left and Right Branch Conditionally Test Bit and Change Test Bit and Clear Test Bit Field and Change Test Bit Field and Clear Signed Bit Field Extract Unsigned Bit Field Extract Bit Field Find First One Bit Field Insert Test Bit Field and Set Test Bit Field Breakpoint Branch Always Test Bit and Set Branch to Subroutine Test Bit Call Module Compare and Swap Operands Compare and Swap Dual Operands Check Register Against Bound Check Register Against Upper and Lower Bound Clear Compare Compare Address Compare Immediate Compare Memory to Memory Compare Register Against Upper and Lower Bounds Test Condition, Decrement and Branch Signed Divide Unsigned Divide Logical Exclusive OR Logical Exclusive Or Immediate Exchange Registers Sign Extend Take Illegal Instruction Trap Jump Jump to Subroutine Load Effective Address Link and Allocate Logical Shift Left and Right Move Move Address Move Condition Code Register Move Status Register Mnemonic MOVE USP MOVEC MOVEM MOVEP MOVEQ MOVES MULS MULU NBCD NEG NEGX NOP NOT OR ORI ORI CCR ORI SR PACK PEA RESET ROL, ROR ROXL,ROXR RTD RTE RTM RTR RTS SBCD Scc STOP SUB SUBA SUBI SUBQ SUBX SWAP TAS TRAP TRAPcc TRAPV TST UNLK UNPK Description Move User Stack Pointer Move Control Register Move Multiple Registers Move Peripheral Move Quick Move Alternate Address Space Signed Multiply Unsigned Multiply Negate Decimal with Extend Negate Negate with Extend No Operation Logical Complement Logical Inclusive OR Logical Inclusive OR Immediate Logical Inclusive Or Immediate to Condition Codes Logical Inclusive OR Immediate to Status Register Pack BCD Push Effective Address Reset External Devices Rotate Left and Right Rotate with Extend Left and Right Return and Deallocate Return from Exception Return from Module Return and Restore Codes Return from Subroutine Subtract Decimal with Extend Set Conditionally Stop Subtract Subtract Address Subtract Immediate Subtract Quick Subtract with Extend Swap Register Words Test and Set an Operand Trap Trap Conditionally Trap on Overflow Test Operand Unlink Unpack BCD Mnemonic cpBcc cpDBcc cpGEN cpRESTORE cpSAVE cpScc cpTRAPcc COPROCESSOR INSTRUCTIONS Description Branch Conditionally Test Coprocessor Condition, Decrement and Branch Coprocessor General Instruction Restore Internal State of Coprocessor Save Internal State of Coprocessor Set Conditionally Trap Conditionally M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-11 Freescale Semiconductor, Inc. 1.5.2 Virtual Machine Freescale Semiconductor, Inc... A typical use for a virtual machine system is the development of software, such as an operating system, for a new machine also under development and not yet available for programming use. In a virtual machine system, a governing operating system emulates the hardware of the new machine and allows the new software to be executed and debugged as though it were running on the new hardware. Since the new software is controlled by the governing operating system, it is executed at a lower privilege level than the governing operating system. Thus, any attempts by the new software to use virtual resources that are not physically present (and should be emulated) are trapped to the governing operating system and performed by its software. In the MC68020/EC020 implementation of a virtual machine, the virtual application runs at the user privilege level. The governing operating system executes at the supervisor privilege level and any attempt by the new operating system to access supervisor resources or execute privileged instructions causes a trap to the governing operating system. Instruction continuation is used to support virtual I/O devices in memory-mapped input/output systems. Control and data registers for the virtual device are simulated in the memory map. An access to a virtual register causes a fault, and the function of the register is emulated by software. 1.6 PIPELINED ARCHITECTURE The MC68020/EC020 contains a three-word instruction pipe where instruction opcodes are decoded. As shown in Figure 1-5, instruction words (instruction operation words and all extension words) enter the pipe at stage B and proceed to stages C and D. An instruction word is completely decoded when it reaches stage D of the pipe. Each stage has a status bit that reflects whether the word in the stage was loaded with data from a bus cycle that was terminated abnormally. Stages of the pipe are only filled in response to specific prefetch requests issued by the sequencer. Words are loaded into the instruction pipe from the cache holding register. Although the individual stages of the pipe are only 16 bits wide, the cache holding register is 32 bits wide and contains the entire long word. This long word is obtained from the instruction cache or the external bus in response to a prefetch request from the sequencer. When the sequencer requests an even-word (long-word-aligned) prefetch, the entire long word is accessed from the instruction cache or the external bus and loaded into the cache holding register, and the high-order word is also loaded into stage B of the pipe. The instruction word for the next sequential prefetch can then be accessed directly from the cache holding register, and no external bus cycle or instruction cache access is required. The cache holding register provides instruction words to the pipe regardless of whether the instruction cache is enabled or disabled. 1-12 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. INSTRUCTION PIPE STAGE D STAGE C STAGE B CACHE HOLDING REGISTER SEQUENCER INSTRUCTION FLOW FROM CACHE AND MEMORY Freescale Semiconductor, Inc... CONTROL UNIT EXECUTION UNIT Figure 1-5. Instruction Pipe The sequencer is either executing microinstructions or awaiting completion of accesses that are necessary to continue executing microcode. The bus controller is responsible for all bus activity. The sequencer controls the bus controller, instruction execution, and internal processor operations such as the calculation of effective addresses and the setting of condition codes. The sequencer initiates instruction word prefetches and controls the validation of instruction words in the instruction pipe. Prefetch requests are simultaneously submitted to the cache holding register, the instruction cache, and the bus controller. Thus, even if the instruction cache is disabled, an instruction prefetch may hit in the cache holding register and cause an external bus cycle to be aborted. 1.7 CACHE MEMORY Due to locality of reference, instructions that are used in a program have a high probability of being reused within a short time. Additionally, instructions that reside in proximity to the instructions currently in use also have a high probability of being utilized within a short period. To exploit these locality characteristics, the MC68020/EC020 contains an on-chip instruction cache. The cache improves the overall performance of the system by reducing the number of bus cycles required by the processor to fetch information from memory and by increasing the bus bandwidth available for other bus masters in the system. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 1-13 Freescale Semiconductor, Inc. SECTION 2 PROCESSING STATES Freescale Semiconductor, Inc... This section describes the processing states of the MC68020/EC020. It describes the functions of the bits in the supervisor portion of the SR and the actions taken by the processor in response to exception conditions. Unless the processor has halted, it is always in either the normal or the exception processing state. Whenever the processor is executing instructions or fetching instructions or operands, it is in the normal processing state. The processor is also in the normal processing state while it is storing instruction results or communicating with a coprocessor. NOTE Exception processing refers specifically to the transition from normal processing of a program to normal processing of system routines, interrupt routines, and other exception handlers. Exception processing includes all stacking operations, the fetch of the exception vector, and the filling of the instruction pipe caused by an exception. Exception processing has completed when execution of the first instruction of the exception handler routine begins. The processor enters the exception processing state when an interrupt is acknowledged, when an instruction is traced or results in a trap, or when some other exception condition arises. Execution of certain instructions or unusual conditions occurring during the execution of any instruction can cause exceptions. External conditions, such as interrupts, bus errors, and some coprocessor responses, also cause exceptions. Exception processing provides an efficient transfer of control to handlers and routines that process the exceptions. A catastrophic system failure occurs whenever the processor receives a bus error or generates an address error while in the exception processing state. This type of failure halts the processor. For example, if during the exception processing of one bus error another bus error occurs, the MC68020/EC020 has not completed the transition to normal processing and has not completed saving the internal state of the machine; therefore, the processor assumes that the system is not operational and halts. Only an external reset can restart a halted processor. (When the processor executes a STOP instruction, it is in a special type of normal processing state--one without bus cycles. It is stopped, not halted.) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 2-1 Freescale Semiconductor, Inc. 2.1 PRIVILEGE LEVELS Freescale Semiconductor, Inc... The processor operates at one of two privilege levels: the user level or the supervisor level. The supervisor level has higher privileges than the user level. Not all processor or coprocessor instructions are permitted to execute at the lower privileged user level, but all are available at the supervisor level. This arrangement allows a separation of supervisor and user so the supervisor can protect system resources from uncontrolled access. The S-bit in the SR is used to select either the user or supervisor privilege level and either the USP or an SSP for stack operations. The processor identifies a bus access (supervisor or user mode) via the function codes so that differentiation between supervisor level and user level can be maintained. In many systems, the majority of programs execute at the user level. User programs can access only their own code and data areas and can be restricted from accessing other information. The operating system typically executes at the supervisor privilege level. It has access to all resources, performs the overhead tasks for the user-level programs, and coordinates user-level program activities. 2.1.1 Supervisor Privilege Level The supervisor level is the higher privilege level. The privilege level is determined by the S-bit of the SR; if the S-bit is set, the supervisor privilege level applies, and all instructions are executable. The bus cycles for instructions executed at the supervisor level are normally classified as supervisor references, and the values of the FC2-FC0 signals refer to supervisor address spaces. In a multitasking operating system, it is more efficient to have a supervisor stack space associated with each user task and a separate stack space for interrupt-associated tasks. The MC68020/EC020 provides two supervisor stacks, master and interrupt; the M bit of the SR selects which of the two is active. When the M-bit is set, references to the SSP implicitly or to address register seven (A7) explicitly, access the MSP. The operating system sets the MSP for each task to point to a task-related area of supervisor data space. This arrangement separates task-related supervisor activity from asynchronous, I/O-related supervisor tasks that may be only coincidental to the currently executing task. The MSP can separately maintain task control information for each currently executing user task, and the software updates the MSP when a task switch is performed, providing an efficient means for transferring task-related stack items. The other supervisor stack pointer, the ISP, can be used for interrupt control information and workspace area as interrupt handling routines require. When the M-bit is clear, the MC68020/EC020 is in the interrupt mode of the supervisor privilege level, and operation is the same as supervisor mode in the MC68000, MC68HC001, MC68008, and MC68010. (The processor is in this mode after a reset operation.) All SSP references access the ISP in this mode. 2-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The value of the M-bit in the SR does not affect execution of privileged instructions; both master and interrupt modes are at the supervisor privilege level. Instructions that affect the M-bit are MOVE to SR, ANDI to SR, EORI to SR, ORI to SR, and RTE. Also, the processor automatically saves the M-bit value and clears it in the SR as part of exception processing for interrupts. All exception processing is performed at the supervisor privilege level. All bus cycles generated during exception processing are supervisor references, and all stack accesses use the active SSP. Freescale Semiconductor, Inc... 2.1.2 User Privilege Level The user level is the lower privilege level. The privilege level is determined by the S-bit of the SR; if the S-bit is clear, the processor executes instructions at the user privilege level. Most instructions execute at either privilege level, but some instructions that have important system effects are privileged and can only be executed at the supervisor level. For instance, user programs are not allowed to execute the STOP instruction or the RESET instruction. To prevent a user program from entering the supervisor privilege level except in a controlled manner, instructions that can alter the S-bit in the SR are privileged. The TRAP #n instruction provides controlled access to operating system services for user programs. The bus cycles for an instruction executed at the user privilege level are classified as user references, and the values of the FC2-FC0 signals specify user address spaces. While the processor is at the user level, references to the system stack pointer implicitly, or to address register seven (A7) explicitly, refer to the USP. 2.1.3 Changing Privilege Level To change from the user to the supervisor privilege level, one of the conditions that causes the processor to perform exception processing must occur. This causes a change from the user level to the supervisor level and can cause a change from the master mode to the interrupt mode. Exception processing saves the current values of the S and M bits of the SR (along with the rest of the SR) on the active supervisor stack, and then sets the S-bit, forcing the processor into the supervisor privilege level. When the exception being processed is an interrupt and the M-bit is set, the M-bit is cleared, putting the processor into the interrupt mode. Execution of instructions continues at the supervisor level to process the exception condition. To return to the user privilege level, a system routine must execute one of the following instructions: MOVE to SR, ANDI to SR, EORI to SR, ORI to SR, or RTE. These instructions execute at the supervisor privilege level and can modify the S-bit of the SR. After these instructions execute, the instruction pipeline is flushed and is refilled from the appropriate address space. The RTE instruction returns to the program that was executing when the exception occurred. It restores the exception stack frame saved on the supervisor stack. If the frame MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 2-3 Freescale Semiconductor, Inc. on top of the stack was generated by an interrupt, trap, or instruction exception, the RTE instruction restores the SR and PC to the values saved on the supervisor stack. The processor then continues execution at the restored PC address and at the privilege level determined by the S-bit of the restored SR. If the frame on top of the stack was generated by a bus fault (bus error or address error exception), the RTE instruction restores the entire saved processor state from the stack. Freescale Semiconductor, Inc... 2.2 ADDRESS SPACE TYPES The processor specifies a target address space for every bus cycle with the FC2-FC0 signals according to the type of access required. In addition to distinguishing between supervisor/user and program/data, the processor can identify special processor cycles, such as the interrupt acknowledge cycle, and the memory management unit can control accesses and translate addresses appropriately. Table 2-1 lists the types of accesses defined for the MC68020/EC020 and the corresponding values of the FC2-FC0 signals. Table 2-1. Address Space Encodings FC2 FC1 FC0 Address Space 0 0 0 (Undefined, Reserved) * 0 0 1 User Data Space 0 1 0 User Program Space 0 1 1 (Undefined, Reserved) * 1 0 0 (Undefined, Reserved) * 1 0 1 Supervisor Data Space 1 1 0 Supervisor Program Space 1 1 1 CPU Space * Address space 3 is reserved for user definition; 0 and 4 are reserved for future use by Motorola. The memory locations of user program and data accesses are not predefined; neither are the locations of supervisor data space. During reset, the first two long words beginning at memory location zero in the supervisor program space are used for processor initialization. No other memory locations are explicitly defined by the MC68020/EC020. A function code of $7 selects the CPU address space. This is a special address space that does not contain instructions or operands but is reserved for special processor functions. The processor uses accesses in this space to communicate with external devices for special purposes. For example, all M68000 processors use the CPU space for interrupt acknowledge cycles. The MC68020/EC020 also generate CPU space accesses for breakpoint acknowledge and coprocessor operations. Supervisor programs can use the MOVES instruction to access all address spaces, including the user spaces and the CPU address space. Although the MOVES instruction can be used to generate CPU space cycles, this may interfere with proper system operation. Thus, the use of MOVES to access the CPU space should be done with caution. 2-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 2.3 EXCEPTION PROCESSING Freescale Semiconductor, Inc... An exception is defined as a special condition that preempts normal processing. Both internal and external conditions can cause exceptions. External conditions that cause exceptions are interrupts from external devices, bus errors, coprocessor-detected errors, and reset. Instructions, address errors, tracing, and breakpoints are internal conditions that cause exceptions. The TRAP, TRAPcc, TRAPV, cpTRAPcc, CHK, CHK2, RTE, BKPT, CALLM, RTM, cp RESTORE, DIVS and DIVU instructions can generate exceptions as part of their normal execution. In addition, illegal instructions, privilege violations, and coprocessor protocol violations cause exceptions. Exception processing, which is the transition from the normal processing of a program to the processing required for the exception condition, involves the exception vector table and an exception stack frame. The following paragraphs describe the exception vectors and a generalized exception stack frame. Exception processing is discussed in detail in Section 6 Exception Processing. Coprocessor-detected exceptions are discussed in detail in Section 7 Coprocessor Interface Description. 2.3.1 Exception Vectors The VBR contains the base address of the 1024-byte exception vector table, which consists of 256 exception vectors. Exception vectors contain the memory addresses of routines that begin execution at the completion of exception processing. These routines perform a series of operations appropriate for the corresponding exceptions. Because the exception vectors contain memory addresses, each consists of one long word, except for the reset vector. The reset vector consists of two long words: the address used to initialize the ISP and the address used to initialize the PC. The address of an exception vector is derived from an 8-bit vector number and the VBR. The vector numbers for some exceptions are obtained from an external device; others are supplied automatically by the processor. The processor multiplies the vector number by four to calculate the vector offset, which it adds to the VBR. The sum is the memory address of the vector. All exception vectors are located in supervisor data space, except the reset vector, which is located in supervisor program space. Only the initial reset vector is fixed in the processor's memory map; once initialization is complete, there are no fixed assignments. Since the VBR provides the base address of the vector table, the vector table can be located anywhere in memory; it can even be dynamically relocated for each task that is executed by an operating system. Details of exception processing are provided in Section 6 Exception Processing, and Table 6-1 lists the exception vector assignments. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 2-5 Freescale Semiconductor, Inc. 2.3.2 Exception Stack Frame Exception processing saves the most volatile portion of the current processor context on the top of the supervisor stack. This context is organized in a format called the exception stack frame. This information always includes a copy of the SR, the PC, the vector offset of the vector, and the frame format field. The frame format field identifies the type of stack frame. The RTE instruction uses the value in the format field to properly restore the information stored in the stack frame and to deallocate the stack space. The general form of the exception stack frame is illustrated in Figure 2-1. Refer to Section 6 Exception Processing for a complete list of exception stack frames. 15 12 Freescale Semiconductor, Inc... SSP 0 STATUS REGISTER PROGRAM COUNTER FORMAT VECTOR OFFSET ADDITIONAL PROCESSOR STATE INFORMATION (2, 6, 12, OR 42 WORDS, IF NEEDED) Figure 2-1. General Exception Stack Frame 2-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SECTION 3 SIGNAL DESCRIPTION Freescale Semiconductor, Inc... This section contains brief descriptions of the input and output signals in their functional groups, as shown in Figure 3-1. Each signal is explained in a brief paragraph with reference to other sections that contain more detail about the signal and the related operations. NOTE In this section and in the remainder of the manual, assert and negate are used to specify forcing a signal to a particular state. In particular, assertion and assert refer to a signal that is active or true; negation and negate indicate a signal that is inactive or false. These terms are used independently of the voltage level (high or low) that they represent. FUNCTION CODES FC2-FC0 ADDRESS BUS **A31-A0 IPL0 IPL1 DATA BUS TRANSFER SIZE IPL2 D31-D0 *IPEND SIZ0 AVEC INTERRU CONTRO SIZ1 BR *OCS *ECS R/W BG MC68020 RMC ASYNCHRONOUS BUS CONTROL AS DS *BGACK BUS ARB CONTRO RESET HALT BERR BUS EXC CONTRO *DBEN DSACK0 CLK DSACK1 VCC EMULATOR SUPPORT CDIS GND Figure 3-1. Functional Signal Groups MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 3-1 Freescale Semiconductor, Inc. 3.1 SIGNAL INDEX The input and output signals for the MC68020/EC020 are listed in Table 3-1. Both the names and mnemonics are shown along with brief signal descriptions. Signals that are implemented in the MC68020, but not in the MC68EC020, have an asterisk (*) preceding the signal name in Table 3-1. Also, note that the address bus is 32 bits wide for the MC68020 and 24 bits wide for the MC68EC020. For more detail on each signal, refer to the paragraph in this section named for the signal and the reference in that paragraph to a description of the related operations. Freescale Semiconductor, Inc... Timing specifications for the signals listed in Table 3-1 can be found in Section 10 Electrical Characteristics. 3.2 FUNCTION CODE SIGNALS (FC2-FC0) These three-state outputs identify the address space of the current bus cycle. Table 2-1 shows the relationships of the function code signals to the privilege levels and the address spaces. Refer to Section 2 Processing States for more information. 3.3 ADDRESS BUS (A31-A0, MC68020)(A23-A0, MC68EC020) These three-state outputs provide the address for the current bus cycle, except in the CPU address space. Refer to Section 2 Processing States for more information on the CPU address space. A31 is the most significant address signal for the MC68020; A23 is the most significant address signal for the MC68EC020. The upper eight bits (A31-A24) are used internally by the MC68EC020 to access the internal instruction cache address tag. Refer to Section 5 Bus Operation for information on the address bus and its relationship to bus operation. 3.4 DATA BUS (D31-D0) These three-state bidirectional signals provide the general-purpose data path between the MC68020/EC020 and all other devices. The data bus can transfer 8, 16, 24, or 32 bits of data per bus cycle. D31 is the most significant bit of the data bus. Refer to Section 5 Bus Operation for more information on the data bus and its relationship to bus operation. 3.5 TRANSFER SIZE SIGNALS (SIZ1, SIZ0) These three-state outputs indicate the number of bytes remaining to be transferred for the current bus cycle. Signals A1, A0, DSACK1, DSACK0, SIZ1, and SIZ0 define the number of bits transferred on the data bus. Refer to Section 5 Bus Operation for more information on SIZ1 and SIZ0 and their use in dynamic bus sizing. 3-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 3-1. Signal Index Signal Name Mnemonic Function Function Codes FC2-FC0 3-bit function code used to identify the address space of each bus cycle. Address Bus MC68020 MC68EC020 A31-A0 A23-A0 32-bit address bus 24-bit address bus Data Bus D31-D0 32-bit data bus used to transfer 8, 16, 24, or 32 bits of data per bus cycle. Freescale Semiconductor, Inc... Size SIZ1, SIZ0 Indicates the number of bytes remaining to be transferred for this cycle. These signals, together with A1 and A0, define the active sections of the data bus. *External Cycle Start ECS Provides an indication that a bus cycle is beginning. *Operand Cycle Start OCS Identical operation to that of ECS except that OCS is asserted only during the first bus cycle of an operand transfer. Read/Write R/ W Defines the bus transfer as a processor read or write. Read-Modify-Write Cycle RMC Provides an indicator that the current bus cycle is part of an indivisible read-modify-write operation. Address Strobe AS Indicates that a valid address is on the bus. Data Strobe DS Indicates that valid data is to be placed on the data bus by an external device or has been placed on the data bus by the MC68020/EC020. *Data Buffer Enable DBEN Provides an enable signal for external data buffers. Data Transfer and Size Acknowledge DSACK1, DSACK0 Bus response signals that indicate the requested data transfer operation has completed. In addition, these two lines indicate the size of the external bus port on a cycle-by-cycle basis and are used for asynchronous transfers. Interrupt Priority Level IPL2-IPL0 Provides an encoded interrupt level to the processor. *Interrupt Pending IPEND Indicates that an interrupt is pending. Autovector AVEC Requests an autovector during an interrupt acknowledge cycle. Bus Request BR Indicates that an external device requires bus mastership. Bus Grant BG Indicates that an external device may assume bus mastership. *Bus Grant Acknowledge BGACK Indicates that an external device has assumed bus mastership. Reset RESET System reset. Halt HALT Indicates that the processor should suspend bus activity or that the processor has halted due to a double bus fault. Bus Error BERR Indicates that an erroneous bus operation is being attempted. Cache Disable CDIS Statically disables the on-chip cache to assist emulator support. Clock CLK Clock input to the processor. Power Supply VCC Power supply. Ground GND Ground connection. *This signal is implemented in the MC68020 and not implemented in the MC68EC020. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 3-3 Freescale Semiconductor, Inc. 3.6 ASYNCHRONOUS BUS CONTROL SIGNALS The following signals control synchronous bus transfer operations for the MC68020/EC020. Note that OCS, ECS, and DBEN are implemented in MC68020 and not implemented in the MC68EC020. Operand Cycle Start (OCS, MC68020 only) This output signal indicates the beginning of the first external bus cycle for an instruction prefetch or a data operand transfer. OCS is not asserted for subsequent cycles that are performed due to dynamic bus sizing or operand misalignment. Refer to Section 5 Bus Operation for information about the relationship of OCS to bus operation. Freescale Semiconductor, Inc... OCS is not implemented in the MC68EC020. External Cycle Start (ECS, MC68020 only) This output signal indicates the beginning of a bus cycle of any type. Refer to Section 5 Bus Operation for information about the relationship of ECS to bus operation. ECS is not implemented in the MC68EC020. Read/Write (R/ W) This three-state output signal defines the type of bus cycle. A high level indicates a read cycle; a low level indicates a write cycle. Refer to Section 5 Bus Operation for information about the relationship of R/W to bus operation. Read-Modify-Write Cycle (RMC) This three-state output signal identifies the current bus cycle as part of an indivisible read-modify-write operation; it remains asserted during all bus cycles of the readmodify-write operation. Refer to Section 5 Bus Operation for information about the relationship of RMC to bus operation. Address Strobe (AS) This three-state output signal indicates that a valid address is on the address bus. The FC2-FC0, SIZ1, SIZ0, and R/W signals are also valid when AS is asserted. Refer to Section 5 Bus Operation for information about the relationship of AS to bus operation. Data Strobe (DS) During a read cycle, this three-state output signal indicates that an external device should place valid data on the data bus. During a write cycle, DS indicates that the MC68020/EC020 has placed valid data on the bus. During two-clock synchronous write cycles, the MC68020/EC020 does not assert DS. Refer to Section 5 Bus Operation for more information about the relationship of DS to bus operation. 3-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Data Buffer Enable (DBEN, MC68020 only) This output signal is an enable signal for external data buffers. This signal may not be required in all systems. Refer to Section 5 Bus Operation for more information about the relationship of DBEN to bus operation. DBEN is not implemented in the MC68EC020. Freescale Semiconductor, Inc... Data Transfer and Size Acknowledge (DSACK1, DSACK0) These input signals indicate the completion of a requested data transfer operation. In addition, they indicate the size of the external bus port at the completion of each cycle. These signals apply only to asynchronous bus cycles. Refer to Section 5 Bus Operation for more information on these signals and their relationship to dynamic bus sizing. 3.7 INTERRUPT CONTROL SIGNALS The following signals are the interrupt control signals for the MC68020/EC020. Note that IPEND is implemented in the MC68020 and not implemented in the MC68EC020. Interrupt Priority Level Signals (IPL2-IPL0) These input signals provide an indication of an interrupt condition and the encoding of the interrupt level from a peripheral or external prioritizing circuitry. IPL2 is the most significant bit of the level number. For example, since the IPL2-IPL0 signals are active low, IPL2-IPL0 equal to $5 corresponds to an interrupt request at interrupt level 2. Refer to Section 6 Exception Processing for information on MC68020/EC020 interrupts. Interrupt Pending (IPEND, MC68020 only) This output signal indicates that an interrupt request exceeding the current interrupt priority mask in the SR has been recognized internally. This output is for use by external devices (coprocessors and other bus masters, for example) to predict processor operation on the following instruction boundaries. Refer to Section 6 Exception Processing for interrupt information. Also, refer to Section 5 Bus Operation for bus information related to interrupts. IPEND is not implemented in the MC68EC020. Autovector (AVEC) This input signal indicates that the MC68020/EC020 should generate an automatic vector during an interrupt acknowledge cycle. Refer to Section 5 Bus Operation for more information about automatic vectors. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 3-5 Freescale Semiconductor, Inc. 3.8 BUS ARBITRATION CONTROL SIGNALS The following signals are the bus arbitration control signals used to determine which device in a system is the bus master. Note that BGACK is implemented in the MC68020 and not implemented in the MC68EC020. Freescale Semiconductor, Inc... Bus Request (BR) This input signal indicates that an external device needs to become the bus master. BR is typically a "wire-ORed" input (but does not need to be constructed from open-collector devices). Refer to Section 5 Bus Operation for more information on MC68020 bus arbitration. Refer to Section 5 Bus Operation and Appendix A Interfacing an MC68EC020 to a DMA Device That Supports a Three-Wire Bus Arbitration Protocol for more information on MC68EC020 bus arbitration. Bus Grant (BG) This output signal indicates that the MC68020/EC020 will release ownership of the bus when the current processor bus cycle completes. Refer to Section 5 Bus Operation for more information on MC68020 bus arbitration. Refer to Section 5 Bus Operation and Appendix A Interfacing an MC68EC020 to a DMA Device That Supports a ThreeWire Bus Arbitration Protocol for more information on MC68EC020 bus arbitration. Bus Grant Acknowledge (BGACK, MC68020 only) This input signal indicates that an external device has become the bus master. Refer to Section 5 Bus Operation for more information on MC68020 bus arbitration. Refer to Section 5 Bus Operation and Appendix A Interfacing an MC68EC020 to a DMA Device That Supports a Three-Wire Bus Arbitration Protocol for more information on MC68EC020 bus arbitration. BGACK is not implemented in the MC68EC020. 3.9 BUS EXCEPTION CONTROL SIGNALS The following signals are the bus exception control signals for the MC68020/EC020. Reset (RESET) This bidirectional open-drain signal is used to initiate a system reset. An external reset signal resets the MC68020/EC020 as well as all external devices. A reset signal from the processor (asserted as part of the RESET instruction) resets external devices only; the internal state of the processor is not altered. Refer to Section 5 Bus Operation for a description of reset bus operation and Section 6 Exception Processing for information about the reset exception. 3-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Halt (HALT) The assertion of this bidirectional open-drain signal indicates that the processor should suspend bus activity or, when used with BERR , that the processor should retry the current cycle. Refer to Section 5 Bus Operation for a description of the effects of HALT on bus operations. When the processor has stopped executing instructions due to a double bus fault condition, the HALT line is asserted by the processor to indicate to external devices that the processor has stopped. Freescale Semiconductor, Inc... Bus Error (BERR) This input signal indicates that an invalid bus operation is being attempted or, when used with HALT, that the processor should retry the current cycle. Refer to Section 5 Bus Operation for a description of the effects of BERR on bus operations. 3.10 EMULATOR SUPPORT SIGNAL The following signal supports emulation by providing a means for an emulator to disable the on-chip cache by supplying internal status information to an emulator. Refer to Section 7 Coprocessor Interface Description for more detailed information on emulation support. Cache Disable (CDIS) This input signal statically disables the on-chip cache to assist emulator support. Refer to Section 4 On-Chip Cache Memory for information about the cache; refer to Section 9 Applications Information for a description of the use of this signal by an emulator. CDIS does not flush the instruction cache; entries remain unaltered and become available again when CDIS is negated. 3.11 CLOCK (CLK) The CLK signal is the clock input to the MC68020/EC020. This TTL-compatible signal should not be gated off at any time while power is applied to the processor. Refer to Section 9 Applications Information for suggestions on clock generation. Refer to Section 10 Electrical Characteristics for electrical characteristics. 3.12 POWER SUPPLY CONNECTIONS The MC68020/EC020 requires connection to a VCC power supply, positive with respect to ground. The VCC connections are grouped to supply adequate current for the various sections of the processor. The ground connections are similarly grouped. Section 11 Ordering Information and Mechanical Data describes the groupings of V CC and ground connections, and Section 9 Applications Information describes a typical power supply interface. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 3-7 Freescale Semiconductor, Inc. 3.13 SIGNAL SUMMARY Table 3-2 provides a summary of the characteristics of the signals discussed in this section. Signal names preceded by an asterisk (*) are implemented in the MC68020 and not implemented in the MC68EC020. Table 3-2. Signal Summary Signal Function Freescale Semiconductor, Inc... Function Codes Signal Name Input/Output Active State Three-State FC2-FC0 Output High Yes Output High Yes Address Bus MC68020 MC68EC020 A31-A0 A23-A0 Data Bus D31-D0 Input/Output High Yes SIZ1, SIZ0 Output High Yes *Operand Cycle Start OCS Output Low No *External Cycle Start ECS Output Low No Read/Write R/ W Output High/Low Yes Read-Modify-Write Cycle RMC Output Low Yes Address Strobe AS Output Low Yes Data Strobe DS Output Low Yes DBEN Output Low Yes DSACK1, DSACK0 Input Low -- IPL2-IPL0 Input Low -- *Interrupt Pending IPEND Output Low No Autovector AVEC Input Low -- Bus Request BR Input Low -- Bus Grant BG Output Low No *Bus Grant Acknowledge BGACK Input Low -- Reset RESET Input/Output Low No ** Halt HALT Input/Output Low No ** Bus Error BERR Input Low -- Cache Disable CDIS Input Low -- Clock CLK Input -- -- Power Supply VCC Input -- -- Ground GND Input -- -- Transfer Size *Data Buffer Enable Data Transfer and Size Acknowledge Interrupt Priority Level *This signal is implemented in the MC68020 and not implemented in the MC68EC020. ** Open-drain 3-8 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SECTION 4 ON-CHIP CACHE MEMORY Freescale Semiconductor, Inc... The MC68020/EC020 incorporates an on-chip cache memory as a means of improving performance. The cache is implemented as a CPU instruction cache and is used to store the instruction stream prefetch accesses from the main memory. An increase in instruction throughput results when instruction words required by a program are available in the on-chip cache and the time required to access them on the external bus is eliminated. In systems with more than one bus master (e.g., a processor and a DMA device), reduced external bus activity increases overall performance by increasing the availability of the bus for use by external devices without degrading the performance of the MC68020/EC020. 4.1 ON-CHIP CACHE ORGANIZATION AND OPERATION The MC68020/EC020 on-chip instruction cache is a direct-mapped cache of 64 long-word entries. Each cache entry consists of a tag field (A31-A8 and FC2), one valid bit, and 32 bits (two words) of instruction data. Figure 4-1 shows a block diagram of the on-chip cache organization. Externally, the MC68EC020 does not use the upper eight bits of the address (A31-A24), and addresses $FF000000 and $00000000 from the MC68EC020 appear the same. However, the MC68EC020 does use A31-A24 internally in the instruction cache address tag, and addresses $FF000000 and $00000000 appear different in the MC68EC020 instruction cache. The MC68020, MC68030/EC030, and MC68040/EC040 use all 32 bits of the address externally. To maintain object-code upgrade compatibility when designing with the MC68EC020, the upper eight bits should be considered part of the address when assigning address spaces in hardware. When enabled, the MC68020/EC020 instruction cache is used to store instruction prefetches (instruction words and extension words) as they are requested by the CPU. Instruction prefetches are normally requested from sequential memory addresses except when a change of program flow occurs (e.g., a branch taken) or when an instruction is executed that can modify the SR. In these cases, the instruction pipe is automatically flushed and refilled. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 4-1 Freescale Semiconductor, Inc. MC68020/EC020 PREFETCH ADDRESS F C 2 F C 1 F C 0 A 3 1 A A A 2 2 2 3 2 1 A A A A A A 2 1 1 1 1 1 0 9 8 7 6 5 A A A A A 1 1 1 1 1 4 3 2 1 0 A A A A 9 8 7 6 A A A A 5 4 3 2 A A 1 0 TAG INDEX Freescale Semiconductor, Inc... TAG V WORD SELECT WORD WORD 1 OF 64 SELECT REPLACEMENT DATA TAG REPLACE VALID TO INSTRUCTION PATH ENTRY HIT COMPARATOR CACHE CONTROL LINE HIT Figure 4-1. MC68020/EC020 On-Chip Cache Organization When an instruction fetch occurs, the cache (if enabled) is first checked to determine if the word required is in the cache. This check is achieved by first using the index field (A7-A2) of the access address as an index into the on-chip cache. This index selects one of the 64 entries in the cache. Next, A31-A8 and FC2 are compared to the tag of the selected entry. (Note that in the MC68EC020, A31-A24 are used for internal on-chip cache tag comparison.) If there is a match and the valid bit is set, a cache hit occurs. A1 is then used to select the proper word from the cache entry, and the cycle ends. If there is no match or if the valid bit is clear, a cache miss occurs, and the instruction is fetched from external memory. This new instruction is automatically written into the cache entry, and the valid bit is set unless the F-bit in the CACR is set. Since the processor always prefetches instructions externally with long-word-aligned bus cycles, both words of the entry will be updated, regardless of which word caused the miss. NOTE Data accesses are not cached, regardless of their associated address space. 4-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 4.2 CACHE RESET During processor reset, the cache is cleared by resetting all of the valid bits. The E and F bits in the CACR are also cleared. 4.3 CACHE CONTROL Freescale Semiconductor, Inc... Only the MC68020/EC020 cache control circuitry can directly access the cache array, but a supervisor program can set bits in the CACR to exercise control over cache operations. The supervisor level also has access to the CAAR, which contains the address for a cache entry to be cleared. System hardware can assert the CDIS signal to disable the cache. The assertion of CDIS disables the cache, regardless of the state of the E-bit in the CACR. CDIS is primarily intended for use by in-circuit emulators. 4.3.1 Cache Control Register (CACR) The CACR, shown in Figure 4-2, is a 32-bit register than can be written or read by the MOVEC instruction or indirectly modified by a reset. Four of the bits (3-0) control the instruction cache. Bits 31-4 are reserved for Motorola definition. They are read as zeros and are ignored when written. For future compatibility, writes should not set these bits. 31 8 0 7 6 5 4 3 2 1 0 0 0 0 0 C CE F E Figure 4-2. Cache Control Register C--Clear Cache The C-bit is set to clear all entries in the instruction cache. Operating systems and other software set this bit to clear instructions from the cache prior to a context switch. The processor clears all valid bits in the instruction cache when a MOVEC instruction sets the C-bit. The C-bit is always read as a zero. CE--Clear Entry In Cache The CE bit is set to clear an entry in the instruction cache. The index field of the CAAR (see Figure 4-3), corresponding to the index and long-word select portion of an address, specifies the entry to be cleared. The processor clears only the specified long word by clearing the valid bit for the entry when a MOVEC instruction sets the CE bit, regardless of the states of the E and F bits. The CE bit is always read as a zero. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 4-3 Freescale Semiconductor, Inc. F--Freeze Cache The F-bit is set to freeze the instruction cache. When the F-bit is set and a cache miss occurs, the entry (or line) is not replaced. When the F-bit is clear, a cache miss causes the entry (or line) to be filled. A reset operation clears the F-bit. Freescale Semiconductor, Inc... E--Enable Cache The E-bit is set to enable the instruction cache. When it is clear, the instruction cache is disabled. A reset operation clears the E-bit. The supervisor normally enables the instruction cache, but it can clear the E-bit for system debugging or emulation, as required. Disabling the instruction cache does not flush the entries. If the cache is reenabled, the previously valid entries remain valid and may be used. 4.3.2 Cache Address Register (CAAR) The format of the 32-bit CAAR is shown in Figure 4-3. 31 8 RESERVED 7 2 INDEX 1 0 RESERVED Figure 4-3. Cache Address Register Bits 31-8, 1, and 0--Reserved These bits are reserved for use by Motorola. Index Field The index field contains the address for the "clear cache entry" operations. The bits of this field, which correspond to A7-A2, specify the index and a long word of a cache line. 4-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... SECTION 5 BUS OPERATION This section provides a functional description of the bus, the signals that control it, and the bus cycles provided for data transfer operations. It also describes the error and halt conditions, bus arbitration, and reset operation. Operation of the bus is the same whether the processor or an external device is the bus master; the names and descriptions of bus cycles are from the point of view of the bus master. For exact timing specifications, refer to Section 10 Electrical Characteristics. The MC68020/EC020 architecture supports byte, word, and long-word operands, allowing access to 8-, 16-, and 32-bit data ports through the use of asynchronous cycles controlled by the DSACK1 and DSACK0 input signals. The MC68020/EC020 allows byte, word, and long-word operands to be located in memory on any byte boundary. For a misaligned transfer, more than one bus cycle may be required to complete the transfer, regardless of port size. For a port less than 32 bits wide, multiple bus cycles may be required for an operand transfer due to either misalignment or a port width smaller than the operand size. Instruction words and their associated extension words must be aligned on word boundaries. The user should be aware that misalignment of word or long-word operands can cause the MC68020/EC020 to perform multiple bus cycles for the operand transfer; therefore, processor performance is optimized if word and long-word memory operands are aligned on word or long-word boundaries, respectively. 5.1 BUS TRANSFER SIGNALS The bus transfers information between the MC68020/EC020 and an external memory, coprocessor, or peripheral device. External devices can accept or provide 8 bits, 16 bits, or 32 bits in parallel and must follow the handshake protocol described in this section. The maximum number of bits accepted or provided during a bus transfer is defined as the port width. The MC68020/EC020 contains an address bus that specifies the address for the transfer and a data bus that transfers the data. Control signals indicate the beginning of the cycle, the address space and size of the transfer, and the type of cycle. The selected device then controls the length of the cycle with the signal(s) used to terminate the cycle. Strobe signals, one for the address bus and another for the data bus, indicate the validity of the address and provide timing information for the data. The bus operates in an asynchronous mode for any port width. The bus and control input signals are internally synchronized to the MC68020/EC020 clock, introducing a delay. This delay is the time period required for the MC68020/EC020 to sample an input signal, synchronize the input to the internal clocks of the processor, and determine whether the MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-1 Freescale Semiconductor, Inc. input is high or low. Figure 5-1 shows the relationship between the clock signal, a typical input, and its associated internal signal. Freescale Semiconductor, Inc... Furthermore, for all inputs, the processor latches the level of the input during a sample window around the falling edge of the clock signal. This window is illustrated in Figure 5-2. To ensure that an input signal is recognized on a specific falling edge of the clock, that input must be stable during the sample window. If an input transitions during the window, the level recognized by the processor is not predictable; however, the processor always resolves the latched level to either a logic high or logic low before using it. In addition to meeting input setup and hold times for deterministic operation, all input signals must obey the protocols described in this section. CLK EXT INT SYNC DELAY Figure 5-1. Relationship between External and Internal Signals t su th CLK EXT SAMPLE WINDOW Figure 5-2. Input Sample Window 5.1.1 Bus Control Signals The MC68020/EC020 initiates a bus cycle by driving the A1-A0, SIZ1, SIZ0, FC2-FC0, and R/W outputs. However, if the MC68020/EC020 finds the required instruction in the onchip cache, the processor aborts the cycle before asserting the AS.The assertion of AS ensures that the cycle has not been aborted by these internal conditions. 5-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... When initiating a bus cycle, the MC68020 asserts ECS in addition to A1-A0, SIZ1, SIZ0, FC2-FC0, and R/W . ECS can be used to initiate various timing sequences that are eventually qualified with AS. Qualification with AS may be required since, in the case of an internal cache hit, a bus cycle may be aborted after ECS has been asserted. During the first MC68020 external bus cycle of an operand transfer, OCS is asserted with ECS. When several bus cycles are required to transfer the entire operand, OCS is asserted only at the beginning of the first external bus cycle. With respect to OCS, an "operand" is any entity required by the execution unit, whether a program or data item. Note that ECS and OCS are not implemented in the MC68EC020. The FC2-FC0 signals select one of eight address spaces (see Table 2-1) to which the address applies. Five address spaces are presently defined. Of the remaining three, one is reserved for user definition, and two are reserved by Motorola for future use. FC2-FC0 are valid while AS is asserted. The SIZ1 and SIZ0 signals indicate the number of bytes remaining to be transferred during an operand cycle (consisting of one or more bus cycles) or during a cache fill operation from a device with a port size that is less than 32 bits. Table 5-2 lists the encoding of SIZ1 and SIZ0. SIZ1 and SIZ0 are valid while AS is asserted. The R/W signal determines the direction of the transfer during a bus cycle. When required, this signal changes state at the beginning of a bus cycle and is valid while AS is asserted. R/W only transitions when a write cycle is preceded by a read cycle or vice versa. This signal may remain low for two consecutive write cycles. The RMC signal is asserted at the beginning of the first bus cycle of a read-modify-write operation and remains asserted until completion of the final bus cycle of the operation. The RMC signal is guaranteed to be negated before the end of state 0 for a bus cycle following a read-modify-write operation. 5.1.2 Address Bus A31-A0 (for the MC68020) or A23-A0 (for the MC68EC020) define the address of the byte (or the most significant byte) to be transferred during a bus cycle. The processor places the address on the bus at the beginning of a bus cycle. The address is valid while AS is asserted. In the MC68EC020, A31-A24 are used internally, but not externally. 5.1.3 Address Strobe AS is a timing signal that indicates the validity of an address on the address bus and of many control signals. It is asserted one-half clock after the beginning of a bus cycle. 5.1.4 Data Bus D31-D0 comprise a bidirectional, nonmultiplexed parallel bus that contains the data being transferred to or from the processor. A read or write operation may transfer 8, 16, 24, or 32 bits of data (one, two, three, or four bytes) in one bus cycle. During a read cycle, the data is latched by the processor on the last falling edge of the clock for that bus cycle. For MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-3 Freescale Semiconductor, Inc. a write cycle, all 32 bits of the data bus are driven, regardless of the port width or operand size. The processor places the data on the data bus one-half clock cycle after A S is asserted in a write cycle. 5.1.5 Data Strobe DS is a timing signal that applies to the data bus. For a read cycle, the processor asserts DS to signal the external device to place data on the bus. DS is asserted at the same time as AS during a read cycle. For a write cycle, DS notifies the external device that the data to be written is valid. The processor asserts DS one full clock cycle after the assertion of AS during a write cycle. Freescale Semiconductor, Inc... 5.1.6 Data Buffer Enable The MC68020 DBEN signal is used to enable external data buffers while data is present on the data bus. During a read operation, DBEN is asserted one clock cycle after the beginning of the bus cycle and is negated as DS is negated. In a write operation, DBEN is asserted at the time AS is asserted and is held active for the duration of the cycle. Note that DBEN is implemented in the MC68020 and is not implemented in the MC68EC020. 5.1.7 Bus Cycle Termination Signals During bus cycles, external devices assert DSACK1/DSACK0 as part of the bus protocol. During a read cycle, DSACK1/DSACK0 assertion signals the processor to terminate the bus cycle and to latch the data. During a write cycle, the assertion of DSACK1/DSACK0 indicates that the external device has successfully stored the data and that the cycle may terminate. DSACK1/DSACK0 also indicate to the processor the size of the port for the bus cycle just completed, as shown in Table 5-1. Refer to 5.3.1 Read Cycle for timing relationships of DSACK1/DSACK0. The BERR signal is also a bus cycle termination indicator and can be used in the absence of DSACK1/DSACK0 to indicate a bus error condition. It can also be asserted in conjunction with DSACK1/DSACK0 to indicate a bus error condition, provided it meets the appropriate timing described in this section and in Section 10 Electrical Characteristics. Additionally, the BERR and HALT signals can be asserted together to indicate a retry termination. Again, the BERR and HALT signals can be simultaneously asserted in lieu of, or in conjunction with, the DSACK1/DSACK0 signals. Finally, the AVEC signal can be used to terminate interrupt acknowledge cycles, indicating that the MC68020/EC020 should generate a vector number to locate an interrupt handler routine. AVEC is ignored during all other bus cycles. 5-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.2 DATA TRANSFER MECHANISM The MC68020/EC020 architecture supports byte, word, and long-word operands allowing access to 8-, 16-, and 32-bit data ports through the use of asynchronous cycles controlled by DSACK1/DSACK0. Byte, word, and long-word operands can be located on any byte boundary, but misaligned transfers may require additional bus cycles, regardless of port size. Freescale Semiconductor, Inc... 5.2.1 Dynamic Bus Sizing The MC68020/EC020 dynamically interprets the port size of the addressed device during each bus cycle, allowing operand transfers to or from 8-, 16-, and 32-bit ports. During an operand transfer cycle, the slave device signals its port size (byte, word, or long word) and indicates completion of the bus cycle to the processor with the DSACK1/DSACK0 signals. Refer to Table 5-1 for DSACK1/DSACK0 encodings and assertion results. Table 5-1. DSACK1/DSACK0 Encodings and Results DSACK1 DSACK0 Negated Negated Insert Wait States in Current Bus Cycle Negated Asserted Complete Cycle--Data Bus Port Size is 8 Bits Asserted Negated Complete Cycle--Data Bus Port Size is 16 Bits Asserted Asserted Complete Cycle--Data Bus Port Size is 32 Bits Result For example, if the processor is executing an instruction that reads a long-word operand from a long-word-aligned address, it attempts to read 32 bits during the first bus cycle. (Refer to 5.2.2 Misaligned Operands for the case of a word or byte address.) If the port responds that it is 32 bits wide, the MC68020/EC020 latches all 32 bits of data and continues with the next operation. If the port responds that it is 16 bits wide, the MC68020/EC020 latches the 16 bits of valid data and runs another bus cycle to obtain the other 16 bits. The operation for an 8-bit port is similar, but requires four read cycles. The addressed device uses the DSACK1/DSACK0 signals to indicate the port width. For instance, a 32-bit device always returns DSACK1/DSACK0 for a 32-bit port, regardless of whether the bus cycle is a byte, word, or long-word operation. Dynamic bus sizing requires that the portion of the data bus used for a transfer to or from a particular port size be fixed. A 32-bit port must reside on D31-D0, a 16-bit port must reside on D32-D16, and an 8-bit port must reside on D31-D24. This requirement minimizes the number of bus cycles needed to transfer data to 8- and 16-bit ports and ensures that the MC68020/EC020 correctly transfers valid data. The MC68020/EC020 always attempts to transfer the maximum amount of data on all bus cycles; for a longword operation, it always assumes that the port is 32 bits wide when beginning the bus cycle. The bytes of operands are designated as shown in Figure 5-3. The most significant byte of a long-word operand is OP0; the least significant byte is OP3. The two bytes of a wordlength operand are OP2 (most significant) and OP3. The single byte of a byte-length operand is OP3. These designations are used in the figures and descriptions that follow. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-5 Freescale Semiconductor, Inc. 31 LONG-WORD OPERAND 0 OP0 OP1 OP2 OP3 OP2 OP3 15 0 WORD OPERAND 7 BYTE OPERAND 0 OP3 Freescale Semiconductor, Inc... Figure 5-3. Internal Operand Representation Figure 5-4 shows the required organization of data ports on the MC68020/EC020 bus for 8-, 16-, and 32-bit devices. The four bytes shown in Figure 5-4 are connected through the internal data bus and data multiplexer to the external data bus. This path is the means through which the MC68020/EC020 supports dynamic bus sizing and operand misalignment. Refer to 5.2.2 Misaligned Operands for the definition of misaligned operand. The data multiplexer establishes the necessary connections for different combinations of address and data sizes. REGISTER OP0 OP1 OP2 OP3 0 1 2 3 MULTIPLEXER INTERNAL TO THE MC68020/EC020 D31- D24 D23-D16 D15-D8 D7-D0 ADDRESS xxxxxxx0 BYTE 0 BYTE 1 BYTE 2 BYTE 3 xxxxxxx0 BYTE 0 BYTE 1 2 BYTE 2 BYTE 3 xxxxxxx0 BYTE 0 1 BYTE 1 2 BYTE 2 3 BYTE 3 EXTERNAL DATA BUS INCREASING MEMORY ADDRESSES ROUTING AND DUPLICATION EXTERNAL BUS 32-BIT PORT 16-BIT PORT 8-BIT PORT Figure 5-4. MC68020/EC020 Interface to Various Port Sizes 5-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The multiplexer takes the four bytes of the 32-bit bus and routes them to their required positions. For example, OP0 can be routed to D31-D24, as would be the normal case, or it can be routed to any other byte position to support a misaligned transfer. The same is true for any of the operand bytes. The positioning of bytes is determined by the SIZ1, SIZ0, A1, and A0 outputs. The SIZ1 and SIZ0 outputs indicate the remaining number of bytes to be transferred during the current bus cycle, as listed in Table 5-2. Freescale Semiconductor, Inc... Table 5-2. SIZ1, SIZ0 Signal Encoding SIZ1 SIZ0 Size Negated Asserted Byte Asserted Negated Word Asserted Asserted 3 Bytes Negated Negated Long Word The number of bytes transferred during a write or read bus cycle is equal to or less than the size indicated by the SIZ1 and SIZ0 outputs, depending on port width and operand alignment. For example, during the first bus cycle of a long-word transfer to a word port, the SIZ1 and SIZ0 outputs indicate that four bytes are to be transferred, although only two bytes are moved on that bus cycle. A1-A0 also affect operation of the data multiplexer. During an operand transfer, A31-A2 (for the MC68020) or A23-A2 (for the MC68EC020) indicate the long-word base address of that portion of the operand to be accessed; A1 and A0 indicate the byte offset from the base. Table 5-3 lists the encodings of A1 and A0 and the corresponding byte offsets from the long-word base. Table 5-3. Address Offset Encodings MOTOROLA A1 A0 Offset Negated Negated +0 Bytes Negated Asserted +1 Byte Asserted Negated +2 Bytes Asserted Asserted +3 Bytes M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-7 Freescale Semiconductor, Inc. Table 5-4 lists the bytes required on the data bus for read cycles. The entries shown as OP3, OP2, OP1, and OP0 are portions of the requested operand that are read or written during that bus cycle and are defined by SIZ1, SIZ0, A1, and A0 for the bus cycle. Table 5-4. Data Bus Requirements for Read Cycles Transfer Size Freescale Semiconductor, Inc... Byte Word 3 Bytes Long Word 5-8 Size Long-Word Port External Data Bytes Required Address SIZ1 SIZ0 A1 A0 0 1 0 0 0 1 0 1 0 1 1 0 0 1 1 1 1 0 0 0 1 0 0 1 1 0 1 0 1 0 1 1 1 1 0 0 1 1 0 1 1 1 1 0 1 1 1 1 0 0 0 0 0 0 0 1 0 0 1 0 0 0 1 1 D31-D24 D23-D16 D15-D8 D7-D0 OP3 Word Port External Data Bytes Required Byte Port External Data Bytes Required D31-D24 D23-D16 D31-D24 OP3 OP3 OP3 OP3 OP3 OP3 OP2 OP3 OP2 OP2 OP3 OP2 OP3 OP2 OP2 OP1 OP2 OP3 OP1 OP1 OP2 OP3 OP1 OP2 OP1 OP1 OP0 OP3 OP1 OP2 OP3 OP0 OP1 OP2 OP0 OP1 OP0 OP0 OP0 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com OP3 OP3 OP3 OP3 OP3 OP2 OP2 OP2 OP3 OP2 OP2 OP2 OP2 OP1 OP1 OP1 OP2 OP1 OP1 OP1 OP1 OP0 OP0 OP0 OP1 OP0 OP0 OP0 MOTOROLA Freescale Semiconductor, Inc. Table 5-5 lists the combinations of SIZ1, SIZ0, A1, and A0 and the corresponding pattern of the data transfer for write cycles from the internal multiplexer of the MC68020/EC020 to the external data bus. Table 5-5. MC68020/EC020 Internal to External Data Bus Multiplexer--Write Cycles Freescale Semiconductor, Inc... Transfer Size Size External Data Bus Connection Address D31-D24 D23-D16 D15-D8 SIZ1 SIZ0 A1 A0 Byte 0 1 x x OP3 OP3 OP3 OP3 Word 1 0 x 0 OP2 OP3 OP2 OP3 1 0 x 1 OP2 OP2 OP3 OP2 1 1 0 0 OP1 OP2 OP3 OP0* 1 1 0 1 OP1 OP1 OP2 OP3 1 1 1 0 OP1 OP2 OP1 OP2 1 1 1 1 OP1 OP1 OP2* OP1 0 0 0 0 OP0 OP1 OP2 OP3 0 0 0 1 OP0 OP0 OP1 OP2 0 0 1 0 OP0 OP1 OP0 OP1 0 0 1 1 OP0 OP0 OP1* OP0 3 Bytes Long Word D7-D0 *Due to the current implementation, this byte is output but never used. x = Don't care NOTE: The OP tables on the external data bus refer to a particular byte of the operand that is written on that section of the data bus. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-9 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Figure 5-5 shows the transfer (write) of a long-word operand to a word port. In the first bus cycle, the MC68020/EC020 places the four operand bytes on the external bus. Since the address is long-word aligned in this example, the multiplexer follows the pattern in the entry of Table 5-5 corresponding to SIZ0, SIZ1, A0, A1 = 0000. The port latches the data on D31-D16, asserts DSACK1 (DSACK0 remains negated), and the processor terminates the bus cycle. It then starts a new bus cycle with SIZ1, SIZ0, A1, A0 = 1010 to transfer the remaining 16 bits. SIZ1 and SIZ0 indicate that a word remains to be transferred; A1 and A0 indicate that the word corresponds to an offset of two from the base address. The multiplexer follows the pattern corresponding to this configuration of SIZ1, SIZ0, A1, and A0 and places the two least significant bytes of the long word on the word portion of the bus (D31-D16). The bus cycle transfers the remaining bytes to the word-sized port. Figure 5-6 shows the timing of the bus transfer signals for this operation. 31 LONG-WORD OPERAND OP0 OP1 D31 DATA BUS 0 OP2 OP3 D16 WORD MEMORY MC68020/EC020 MEMORY CONTROL MSB LSB SIZ1 SIZ0 A1 A0 DSACK1 DSACK0 OP0 OP1 0 0 0 0 L H OP2 OP3 1 0 1 0 L H Figure 5-5. Long-Word Operand Write to Word Port Example 5-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 CLK * A31-A2 A1 A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP2 D23-D16 OP1 OP3 WORD WRITE WORD WRITE LONG-WORD OPERAND WRITE TO 16-BIT PORT * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-6. Long-Word Operand Write to Word Port Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-11 Freescale Semiconductor, Inc. Figure 5-7 shows a word write to an 8-bit bus port. Like the preceding example, this example requires two bus cycles. Each bus cycle transfers a single byte. SIZ1 and SIZ0 for the first cycle specify two bytes; for the second cycle, one byte. Figure 5-8 shows the associated bus transfer signal timing. WORD OPERAND 15 OP2 0 OP3 D31 DATA BUS D24 Freescale Semiconductor, Inc... BYTE MEMORY MC68020/EC020 OP2 SIZ1 1 OP3 0 SIZ0 A1 0 0 1 0 MEMORY CONTROL A0 0 DSACK1 H DSACK0 L 1 H L Figure 5-7. Word Operand Write to Byte Port Example 5-12 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 CLK * A31-A2 A1 A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 D23-D16 D15-D8 D7-D0 BYTE WRITE BYTE WRITE WORD OPERAND WRITE * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-8. Word Operand Write to Byte Port Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-13 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... 5.2.2 Misaligned Operands Since operands may reside at any byte boundary, they may be misaligned. A byte operand is properly aligned at any address; a word operand is misaligned at an odd address; a long word is misaligned at an address that is not evenly divisible by four. The MC68000, MC68008, and MC68010 implementations allow long-word transfers on oddword boundaries but force exceptions if word or long-word operand transfers are attempted at odd-byte addresses. Although the MC68020/EC020 does not enforce any alignment restrictions for data operands (including PC relative data addresses), some performance degradation occurs when additional bus cycles are required for long-word or word operands that are misaligned. For maximum performance, data items should be aligned on their natural boundaries. All instruction words and extension words must reside on word boundaries. Attempting to prefetch an instruction word at an odd address causes an address error exception. Figure 5-9 shows the transfer (write) of a long-word operand to an odd address in wordorganized memory, which requires three bus cycles. For the first cycle, SIZ1 and SIZ0 specify a long-word transfer, and A2-A0 = 001. Since the port width is 16 bits, only the first byte of the long word is transferred. The slave device latches the byte and acknowledges the data transfer, indicating that the port is 16 bits wide. When the processor starts the second cycle, SIZ1 and SIZ0 specify that three bytes remain to be transferred with A2-A0 = 010. The next two bytes are transferred during this cycle. The processor then initiates the third cycle, with SIZ1 and SIZ0 indicating one byte remaining to be transferred with A2-A0 = 100. The port latches the final byte, and the operation is complete. Figure 5-10 shows the associated bus transfer signal timing. Figure 5-11 shows the equivalent operation for a data read cycle. 31 LONG-WORD OPERAND OP0 OP1 D31 DATA BUS 0 OP2 OP3 D16 MC68020/EC020 WORD MEMORY MSB LSB XXX OP0 0 0 0 0 1 L H OP1 OP2 1 1 0 1 0 L H 0 0 L H OP3 XXX 0 SIZ0 A2 MEMORY CONTROL SIZ1 1 1 A1 A0 DSACK1 DSACK0 Figure 5-9. Misaligned Long-Word Operand Write to Word Port Example 5-14 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 S4 CLK * A31-A2 A1 A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP1 OP3 D23-D16 OP0 OP2 OP3 D15-D8 OP1 OP1 OP3 D7-D0 OP2 OP2 OP3 BYTE WRITE WORD WRITE BYTE WRITE LONG-WORD OPERAND WRITE the MC68EC020, A23-A2. * For This signal does not apply to the MC68EC020. Figure 5-10. Misaligned Long-Word Operand Write to Word Port Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-15 Freescale Semiconductor, Inc. LONG-WORD OPERAND (REGISTER) 31 OP0 OP1 0 OP2 D31 DATA BUS OP3 D16 Freescale Semiconductor, Inc... WORD MEMORY MSB LSB MEMORY CONTROL MC68020/EC020 A1 A0 DSACK1 DSACK0 XXX OP0 SIZ1 SIZ0 A2 0 0 0 0 1 L H OP1 OP2 1 1 0 1 0 L H OP3 XXX 0 1 1 0 0 L H Figure 5-11. Misaligned Long-Word Operand Read from Word Port Example Figures 5-12 and 5-13 show a word transfer (write) to an odd address in word-organized memory. This example is similar to the one shown in Figures 5-9 and 5-10 except that the operand is word sized and the transfer requires only two bus cycles. Figure 5-14 shows the equivalent operation for a data read cycle. WORD OPERAND 15 OP2 0 OP3 D31 DATA BUS D16 WORD MEMORY MC68020/EC020 SIZ0 A2 MEMORY CONTROL MSB LSB SIZ1 A1 A0 DSACK1 DSACK0 XXX OP2 1 0 0 0 1 L H OP3 XXX 0 1 0 1 0 L H Figure 5-12. Misaligned Word Operand Write to Word Port Example 5-16 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP2 OP3 D23-D16 OP2 OP3 D15-D8 OP3 OP3 D7-D0 OP2 OP3 WORD WRITE BYTE WRITE WORD OPERAND WRITE TO A1, A0 = 01 * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-13. Misaligned Word Operand Write to Word Port Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-17 Freescale Semiconductor, Inc. 15 WORD OPERAND (REGISTER) OP2 0 OP3 D31 DATA BUS D16 Freescale Semiconductor, Inc... WORD MEMORY MC68020/EC020 SIZ0 A2 MEMORY CONTROL MSB LSB SIZ1 A1 A0 DSACK1 DSACK0 XXX OP2 1 0 0 0 1 L H OP3 XXX 0 1 0 1 0 L H Figure 5-14. Misaligned Word Operand Read from Word Bus Example Figures 5-15 and 5-16 show an example of a long-word transfer (write) to an odd address in long-word-organized memory. In this example, a long-word access is attempted beginning at the least significant byte of a long-word-organized memory. Only one byte can be transferred in the first bus cycle. The second bus cycle then consists of a threebyte access to a long-word boundary. Since the memory is long word organized, no further bus cycles are necessary. Figure 5-17 shows the equivalent operation for a data read cycle. LONG-WORD OPERAND 31 OP0 OP1 D31 OP2 0 OP3 DATA BUS D0 LONG-WORD MEMORY MC68020/EC020 MSB UMB LMB LSB SIZ1 SIZ0 A2 XXX XXX XXX OP0 0 0 OP1 OP2 OP3 XXX 1 1 MEMORY CONTROL A1 A0 DSACK1 DSACK0 0 1 1 L L 1 0 0 L L Figure 5-15. Misaligned Long-Word Operand Write to Long-Word Port Example 5-18 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP1 D23-D16 OP0 OP2 D15-D8 OP1 OP3 D7-D0 OP0 OP1 BYTE WRITE 3-BYTE WRITE LONG-WORD OPERAND WRITE * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-16. Misaligned Long-Word Operand Write to Long-Word Port Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-19 Freescale Semiconductor, Inc. 31 LONG-WORD OPERAND (REGISTER) OP0 OP1 D31 OP2 0 OP3 DATA BUS D0 Freescale Semiconductor, Inc... LONG-WORD MEMORY MC68020/EC020 MSB UMB LMB LSB SIZ1 SIZ0 A2 XXX XXX XXX OP0 0 0 OP1 OP2 OP3 XXX 1 1 MEMORY CONTROL A1 A0 DSACK1 DSACK0 0 1 1 L L 1 0 0 L L Figure 5-17. Misaligned Long-Word Operand Read from Long-Word Port Example 5.2.3 Effects of Dynamic Bus Sizing and Operand Misalignment The combination of operand size, operand alignment, and port size determine the number of bus cycles required to perform a particular memory access. Table 5-6 lists the number of bus cycles required for different operand sizes to different port sizes with all possible alignment conditions for read/write cycles. Table 5-6. Memory Alignment and Port Size Influence on Read/Write Bus Cycles Number of Bus Cycles (Data Port Size = 32 Bits:16 Bits:8 Bits) A1, A0 Operand Size 00 01 10 11 Instruction * 1:2:4 N/A N/A N/A Byte Operand 1:1:1 1:1:1 1:1:1 1:1:1 Word Operand 1:1:2 1:2:2 1:1:2 2:2:2 Long-Word Operand 1:2:4 2:3:4 2:2:4 2:3:4 *Instruction prefetches are always two words from a long-word boundary Table 5-6 reveals that bus cycle throughput is significantly affected by port size and alignment. The MC68020/EC020 system designer and programmer should be aware of and account for these effects, particularly in time-critical applications. 5-20 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 5-6 demonstrates that the processor always prefetches instructions by reading a long word from a long-word address (A1, A0 = 00), regardless of port size or alignment. When the required instruction begins at an odd-word boundary, the processor attempts to fetch the entire 32 bits and loads both words into the instruction cache, if possible, although the second one is the required word. Even if the instruction access is not cached, the entire 32 bits are latched into an internal cache holding register from which the two instructions words can subsequently be referenced. Refer to Section 8 Instruction Execution Timing for a complete description of the cache holding register and pipeline operation. Freescale Semiconductor, Inc... 5.2.4 Address, Size, and Data Bus Relationships The data transfer examples show how the MC68020/EC020 drives data onto or receives data from the correct byte sections of the data bus. Table 5-7 shows the combinations of the SIZ1, SIZ0, A1, and A0 signals that can be used to generate byte enable signals for each of the four sections of the data bus for read and write cycles if the addressed device requires them. The port size also affects the generation of these enable signals as shown in the table. The four columns on the right correspond to the four byte enable signals. Letters B, W, and L refer to port sizes: B for 8-bit ports, W for 16-bit ports, and L for 32-bit ports. The letters B, W, and L imply that the byte enable signal should be true for that port size. A dash (--) implies that the byte enable signal does not apply. The MC68020/EC020 always drives all sections of the data bus because, at the beginning of a write cycle, the bus controller does not know the port size. Table 5-7 reveals that the MC68020/EC020 transfers the number of bytes specified by SIZ1, SIZ0 to or from the specified address unless the operand is misaligned or unless the number of bytes is greater than the port width. In these cases, the device transfers the greatest number of bytes possible for the port. For example, if the size is four and A1, A0 = 01, a 32-bit slave can only receive three bytes in the current bus cycle. A 16- or 8-bit slave can only receive one byte. The table defines the byte enables for all port sizes. Byte data strobes can be obtained by combining the enable signals with the DS signal. Devices residing on 8-bit ports can use the data strobe by itself since there is only one valid byte for every transfer. These enable or strobe signals select only the bytes required for write or read cycles. The other bytes are not selected, which prevents incorrect accesses in sensitive areas such as I/O. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-21 Freescale Semiconductor, Inc. Table 5-7. Data Bus Byte Enable Signals for Byte, Word, and Long-Word Ports Data Bus Active Sections Byte (B), Word (W) , Long-Word (L) Ports Freescale Semiconductor, Inc... Transfer Size SIZ1 SIZ0 A1 A0 D31-D24 D23-D16 D15-D8 D7-D0 Byte 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 BWL B BW B -- WL -- W -- -- L -- -- -- -- L Word 1 1 1 1 0 0 0 0 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W -- L L -- -- -- L L 3 Bytes 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W L L L -- -- L L L Long Word 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W L L L -- L L L L Figure 5-18 shows a logic diagram of one method for generating byte enable signals for 16- and 32-bit ports from the SIZ1, SIZ0, A1, and A0 encodings and the R/W signal. 5.2.5 Cache Interactions The organization and requirements of the on-chip instruction cache affect the interpretation of DSACK1 and DSACK0. Since the MC68020/EC020 attempts to load all instructions into the on-chip cache, the bus may operate differently when caching is enabled. Specifically, on read cycles that terminate normally, the A1, A0, SIZ1, and SIZ0 signals do not apply. The cache can also affect the assertion of AS and the operation of a read cycle. The search of the cache by the processor begins when the sequencer requires an instruction. At this time, the bus controller may also initiate an external bus cycle in case the requested item is not resident in the instruction cache. If an internal cache hit occurs, the external cycle aborts, and AS is not asserted. For the MC68020, if the bus is not occupied with another read or write cycle, the bus controller asserts the ECS signal (and the OCS signal, if appropriate). It is possible to have ECS asserted on multiple consecutive clock cycles. Note that there is a minimum time specified from the negation of ECS to the next assertion of ECS (refer to Section 10 Electrical Characteristics). Instruction prefetches can occur every other clock so that if, after an aborted cycle due to an instruction cache hit, the bus controller asserts ECS on the next clock, this second cycle is for a data fetch. Note that, if the bus controller is executing other cycles, these aborted cycles due to cache hits may not be seen externally. 5-22 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. UUD Freescale Semiconductor, Inc... UMD LMD LLD UD LD A0 A1 SIZ0 UUD = UPPER UPPER DATA (32-BIT PORT) UMD = UPPER MIDDLE DATA (32-BIT PORT) LMD = LOWER MIDDLE DATA (32-BIT PORT) LLD = LOWER LOWER DATA (32-BIT PORT) UD = UPPER DATA (16-BIT PORT) LD = LOWER DATA (16-BIT PORT) SIZ1 R/W Figure 5-18. Byte Enable Signal Generation for 16- and 32-Bit Ports MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-23 Freescale Semiconductor, Inc. 5.2.6 Bus Operation Freescale Semiconductor, Inc... The MC68020/EC020 bus is used in an asynchronous manner allowing external devices to operate at clock frequencies different from the MC68020/EC020 clock. Bus operation uses the handshake lines (AS, DS, DSACK0, DSACK1, BERR, and HALT) to control data transfers. AS signals the start of a bus cycle, and DS is used as a condition for valid data on a write cycle. Decoding SIZ1, SIZ0, A1, and A0 provides byte enable signals that select the active portion of the data bus. The slave device (memory or peripheral) then responds by placing the requested data on the correct portion of the data bus for a read cycle or latching the data on a write cycle and by asserting the DSACK0/DSACK1 combination that corresponds to the port size to terminate the cycle. If no slave responds or the access is invalid, external control logic asserts BERR to abort or BERR and HALT to retry the bus cycle. DSACK1/DSACK0 can be asserted before the data from a slave device is valid on a read cycle. The length of time that DSACK1/DSACK0 may precede data is given by parameter #31, and it must be met in any asynchronous system to ensure that valid data is latched into the processor. (Refer to Section 10 Electrical Characteristics for timing parameters.) Note that no maximum time is specified from the assertion of AS to the assertion of DSACK1/DSACK0. Although the processor can transfer data in a minimum of three clock cycles when the cycle is terminated with DSACK1/DSACK0, the processor inserts wait cycles in clock period increments until DSACK1/DSACK0 is recognized. The BERR and/or HALT signals can be asserted after DSACK1/ DSACK0 is asserted. BERR and/or HALT must be asserted within the time given (parameter #48), after DSACK1/DSACK0 is asserted in any asynchronous system. If this maximum delay time is violated, the processor may exhibit erratic behavior. 5.2.7 Synchronous Operation with DSACK1/ DSACK0 Although cycles terminated with DSACK1/DSACK0 are classified as asynchronous, cycles terminated with DSACK1/DSACK0 can also operate synchronously in that signals are interpreted relative to clock edges. The devices that use these synchronous cycles must synchronize the responses to the MC68020/EC020 clock. Since these devices terminate bus cycles with D S A C K 1/D S A C K 0 , the dynamic bus sizing capabilities of the MC68020/EC020 are available. In addition, the minimum cycle time for these synchronous cycles is three clocks. To support systems that use the system clock to generate DSACK1/DSACK0 and other asynchronous inputs, the asynchronous input setup time (parameter #47A) and the asynchronous input hold time (parameter #47B) are provided in Section 10 Electrical Characteristics. (Note: although a misnomer, these "asynchronous" parameters are the setup and hold times for synchronous operation.) If the setup and hold times are met for the assertion or negation of a signal, such as DSACK1/DSACK0, the processor can be guaranteed to recognize that signal level on that specific falling edge of the system clock. If the assertion of DSACK1/DSACK0 is recognized on a particular falling edge of the clock, valid data is latched into the processor (for a read cycle) on the next falling clock edge provided the data meets the data setup time (parameter #27). In this case, parameter #31 5-24 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... for asynchronous operation can be ignored. All timing parameters referred to are described in Section 10 Electrical Characteristics. If a system asserts DSACK1/DSACK0 for the required window around the falling edge of state 2 and obeys the proper bus protocol by maintaining DSACK1/DSACK0 (and/or BERR/HALT) until and throughout the clock edge that negates AS (with the appropriate asynchronous input hold time specified by parameter #47B), no wait states are inserted. The bus cycle runs at its maximum speed of three clocks per cycle for bus cycles terminated with DSACK1/DSACK0. To ensure proper operation in a synchronous system when BERR or BERR/HALT is asserted after DSACK1/DSACK0, BERR (and HALT) must meet the appropriate setup time (parameter #27A) prior to the falling clock edge one clock cycle after DSACK1/DSACK0 is recognized. This setup time is critical, and the MC68020/EC020 may exhibit erratic behavior if it is violated. When operating synchronously, the data-in setup (parameter #27) and hold (parameter #30) times for synchronous cycles may be used instead of the timing requirements for data relative to the DS signal. 5.3 DATA TRANSFER CYCLES The transfer of data between the processor and other devices involves the following signals: * Address Bus (A31-A0 for the MC68020) (A23-A0 for the MC68EC020) * Data Bus (D31-D0) * Control Signals The address and data buses are both parallel, nonmultiplexed buses. The bus master moves data on the bus by issuing control signals, and the bus uses a handshake protocol to ensure correct movement of the data. In all bus cycles, the bus master is responsible for de-skewing all signals it issues at both the start and end of the cycle. In addition, the bus master is responsible for de-skewing DSACK1/DSACK0, D31-D0, BERR, HALT, and, for the MC68020, DBEN from the slave devices. The following paragraphs define read, write, and read-modify-write cycle operations. Each of the bus cycles is defined as a succession of states. These states apply to the bus operation and are different from the processor states described in Section 2 Processing States. The clock cycles used in the descriptions and timing diagrams of data transfer cycles are independent of the clock frequency. Bus operations are described in terms of external bus states. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-25 Freescale Semiconductor, Inc. 5.3.1 Read Cycle Freescale Semiconductor, Inc... During a read cycle, the processor receives data from a memory, coprocessor, or peripheral device. If the instruction specifies a long-word operation, the MC68020/EC020 attempts to read four bytes at once. For a word operation, it attempts to read two bytes at once and for a byte operation, one byte. For some operations, the processor requests a three-byte transfer. The processor properly positions each byte internally. The section of the data bus from which each byte is read depends on the operand size, A1-A0, and the port size. Refer to 5.2.1 Dynamic Bus Sizing and 5.2.2 Misaligned Operands for more information on dynamic bus sizing and misaligned operands. Figure 5-19 is a flowchart of a long-word read cycle. Figure 5-20 is a flowchart of a byte read cycle. Figures 5-21-5-23 are read cycle timing diagrams in terms of clock periods. Figure 5-21 corresponds to byte and word read cycles from a 32-bit port. Figure 5-22 corresponds to a long-word read cycle from an 8-bit port. Figure 5-23 also applies to a long-word read cycle, but from 16- and 32-bit ports. PROCESSOR EXTERNAL DEVICE ADDRESS DEVICE * 1) ASSERT ECS/OCS FOR ONE-HALF CLOCK 2) ** 3) 4) 5) 6) 7) * 8) SET R/W TO READ DRIVE ADDRESS ON A31-A0 DRIVE FUNCTION CODE ON FC2-FC0 DRIVE SIZ1, SIZ0 (FOUR BYTES) ASSERT AS ASSERT DS ASSERT DBEN PRESENT DATA 1) DECODE ADDRESS 2) PLACE DATA ON D31-D0 3) ASSERT DSACK1/DSACK0 ACQUIRE DATA 1) LATCH DATA 2) NEGATE AS AND DS * 3) NEGATE DBEN TERMINATE CYCLE 1) REMOVE DATA FROM D31-D0 2) NEGATE DSACK1/DSACK0 START NEXT CYCLE step does not apply to the MC68EC020. * This For the MC68EC020, A23-A0. Figure 5-19. Long-Word Read Cycle Flowchart 5-26 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. PROCESSOR EXTERNAL DEVICE Freescale Semiconductor, Inc... ADDRESS DEVICE * 1) ASSERT ECS/OCS FOR ONE-HALF CLOCK 2) ** 3) 4) 5) 6) 7) * 8) SET R/W TO READ DRIVE ADDRESS ON A31-A0 DRIVE FUNCTION CODE ON FC2-FC0 DRIVE SIZ1, SIZ0 (FOUR BYTES) ASSERT AS ASSERT DS ASSERT DBEN PRESENT DATA 1) DECODE ADDRESS 2) PLACE DATA ON D31-D24 OR D23-D16 OR D15-D8 OR D7-D0 (BASED ON A1, A0, AND BUS WIDTH) 3) ASSERT DSACK1/DSACK0 ACQUIRE DATA 1) LATCH DATA 2) NEGATE AS AND DS * 3) NEGATE DBEN TERMINATE CYCLE 1) REMOVE DATA FROM D31-D0 2) NEGATE DSACK1/DSACK0 START NEXT CYCLE * This step does not apply to the MC68EC020. ** For the MC68EC020, A23-A0. Figure 5-20. Byte Read Cycle Flowchart MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-27 Freescale Semiconductor, Inc. S0 S2 S4 S0 S4 S2 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... WORD BYTE SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP2 D23-D16 OP3 D15-D8 OP3 D7-D0 OP3 WORD READ BYTE READ BYTE READ * Figure 5-21. Byte and Word Read Cycles--32-Bit Port 5-28 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 S4 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... LONG WORD 3-BYTE WORD BYTE SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP2 OP1 OP3 D23-D16 D15-D8 D7-D0 BYTE READ BYTE READ BYTE READ BYTE READ LONG-WORD OPERAND READ FROM 8-BIT PORT the MC68EC020, A23-A2. * For This signal does not apply to the MC68EC020. Figure 5-22. Long-Word Read--8-Bit Port MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-29 Freescale Semiconductor, Inc. S0 S2 S4 S0 S4 S2 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... LONG WORD WORD LONG WORD SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP2 OP0 D23-D16 OP1 OP3 OP1 D15-D8 OP2 D7-D0 OP3 WORD READ WORD READ LONG-WORD READ FROM 32-BIT PORT LONG-WORD OPERAND READ FROM 16-BIT PORT * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-23. Long-Word Read--16- and 32-Bit Ports 5-30 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State 0 MC68020--The read cycle starts in state 0 (S0). The processor asserts ECS, indicating the beginning of an external cycle. If the cycle is the first external cycle of a read operation, OCS is asserted simultaneously. During S0, the processor places a valid address on A31-A0 and valid function codes on FC2-FC0. The function codes select the address space for the cycle. The processor drives R/W high for a read cycle and negates DBEN to disable the data buffers. SIZ0 and SIZ1 become valid, indicating the number of bytes requested to be transferred. MC68EC020--The read cycle starts in S0. During S0, the processor places a valid address on A23-A0 and valid function codes on FC2-FC0. The function codes select the address space for the cycle. The processor drives R/W high for a read cycle. SIZ0 and SIZ1 become valid, indicating the number of bytes requested to be transferred. State 1 MC68020--One-half clock later in state 1 (S1), the processor asserts AS, indicating that the address on the address bus is valid. The processor also asserts DS during S1. In addition, the ECS (and OCS, if asserted) signal is negated during S1. MC68EC020--One-half clock later in S1, the processor asserts AS, indicating that the address on the address bus is valid. The processor also asserts DS during S1. State 2 MC68020--During state 2 (S2), the processor asserts DBEN to enable external data buffers. The selected device uses R/W, SIZ1-SIZ0, A1-A0, and DS to place its information on the data bus. Any or all of the bytes (D31-D24, D23-D16, D15-D8, and D7-D0) are selected by SIZ1-SIZ0 and A1-A0. Concurrently, the selected device asserts DSACK1/DSACK0. MC68EC020--During S2, the selected device uses R/W, SIZ1-SIZ0, A1-A0, and DS to place its information on the data bus. Any or all of the bytes (D31-D24, D23-D16, D15-D8, and D7-D0) are selected by SIZ1-SIZ0 and A1-A0. Concurrently, the selected device asserts DSACK1/DSACK0. State 3 MC68020/EC020--As long as at least one of the DSACK1/DSACK0 signals is recognized by the end of S2 (meeting the asynchronous input setup time requirement), data is latched on the next falling edge of the clock, and the cycle terminates. If DSACK1/DSACK0 is not recognized by the start of state 3 (S3), the processor inserts wait states instead of proceeding to states 4 and 5. To ensure that wait states are inserted, both DSACK1 and D S A C K 0 must remain negated throughout the asynchronous input setup and hold times around the end of S2. If wait states are added, the processor continues to sample the DSACK1/DSACK0 signals on the falling edges of the clock until an assertion is recognized. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-31 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State 4 MC68020/EC020--At the end of state 4 (S4), the processor latches the incoming data. State 5 MC68020--The processor negates AS, DS, and DBEN during state 5 (S5). It holds the address valid during S5 to provide address hold time for memory systems. R/W, SIZ1- SIZ0, and FC2-FC0 also remain valid throughout S5. The external device keeps its data and DSACK1/DSACK0 signals asserted until it detects the negation of AS or DS (whichever it detects first). The device must remove its data and negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of AS or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next bus cycle. MC68EC020--The processor negates AS and DS during state S5. It holds the address valid during S5 to provide address hold time for memory systems. R/W , SIZ1, SIZ0, and FC2-FC0 also remain valid throughout S5. The external device keeps its data and DSACK1/DSACK0 signals asserted until it detects the negation of AS or DS (whichever it detects first). The device must remove its data and negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of AS or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next bus cycle. 5-32 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.3.2 Write Cycle During a write cycle, the processor transfers data to memory or a peripheral device. Figure 5-24 is a flowchart of a write cycle operation for a long-word transfer. Figures 5-25- 5-28 are write cycle timing diagrams in terms of clock periods. Figure 5-25 shows two write cycles (between two read cycles with no idle time in between) for a 32-bit port. Figure 5-26 shows byte and word write cycles to a 32-bit port. Figure 5-27 shows a longword write cycle to an 8-bit port. Figure 5-28 shows a long-word write cycle to a 16-bit port. PROCESSOR EXTERNAL DEVICE Freescale Semiconductor, Inc... ADDRESS DEVICE * 1) ASSERT ECS/OCS FOR ONE-HALF CLOCK ** 2) DRIVE ADDRESS ON A31-A0 3) 4) 5) 6) * 7) 8) 9) DRIVE FUNCTION CODES ON FC2-FC0 DRIVE SIZ1, SIZ0 (FOUR BYTES) SET R/W TO WRITE ASSERT AS ASSERT DBEN DRIVE DATA LINES D31-D0 ASSERT DS TERMINATE OUTPUT TRANSFER ACCEPT DATA 1) DECODE ADDRESS 2) STORE DATA FROM D31-D0 3) ASSERT DSACK1/DSACK0 1) NEGATE AS AND DS 2) REMOVE DATA FROM D31-D0 * 3) NEGATE DBEN TERMINATE CYCLE 1) NEGATE DSACK1/DSACK0 START NEXT CYCLE * This step does not apply to the MC68EC020. ** For the MC68EC020, A23-A0. Figure 5-24. Write Cycle Flowchart MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-33 Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 S4 S0 S2 Sw Sw S4 CLK *A31-A2 A1 A0 Freescale Semiconductor, Inc... FC2-FC0 SIZ1 LONG WORD SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 BYTE READ WRITE WRITE READ WITH WAIT STATES * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-25. Read-Write-Read Cycles--32-Bit Port 5-34 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S4 S2 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... WORD BYTE SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP2 OP3 OP3 D23-D16 OP3 OP3 OP3 D15-D8 OP2 OP3 OP3 D7-D0 OP3 OP3 OP3 WORD WRITE BYTE WRITE BYTE WRITE the MC68EC020, A23-A2. * For This signal does not apply to the MC68EC020. Figure 5-26. Byte and Word Write Cycles--32-Bit Port MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-35 Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 S4 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... LONG WORD 3-BYTE WORD BYTE SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP1 OP2 OP3 D23-D16 OP1 OP1 OP3 OP3 D15-D8 OP2 OP2 OP2 OP3 D7-D0 OP3 OP3 OP3 OP3 BYTE WRITE BYTE WRITE BYTE WRITE BYTE WRITE LONG-WORD OPERAND WRITE TO 8-BIT PORT the MC68EC020, A23-A2. * For This signal does not apply to the MC68EC020. Figure 5-27. Long-Word Operand Write--8-Bit Port 5-36 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S4 S2 S0 S2 S4 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... LONG WORD WORD LONG WORD SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 OP0 OP2 OP0 D23-D16 OP1 OP3 OP1 D15-D8 OP2 OP2 OP2 D7-D0 OP3 OP3 OP3 WORD WRITE WORD WRITE LONG-WORD WRITE TO 32-BIT PORT LONG-WORD OPERAND WRITE TO 16-BIT PORT * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-28. Long-Word Operand Write--16-Bit Port MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-37 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State 0 MC68020--The write cycle starts in S0. The processor negates ECS, indicating the beginning of an external cycle. If the cycle is the first external cycle of a write operation, OCS is asserted simultaneously. During S0, the processor places a valid address on A31-A0 and valid function codes on FC2-FC0. The function codes select the address space for the cycle. The processor drives R/W low for a write cycle. SIZ1- SIZ0 become valid, indicating the number of bytes to be transferred. MC68EC020--The write cycle starts in S0. During S0, the processor places a valid address on A23-A0 and valid function codes on FC2-FC0. The function codes select the address space for the cycle. The processor drives R/W low for a write cycle. SIZ1, SIZ0 become valid, indicating the number of bytes to be transferred. State 1 MC68020--One-half clock later in S1, the processor asserts AS, indicating that the address on the address bus is valid. The processor also asserts DBEN during S1, which can enable external data buffers. In addition, the ECS (and OCS, if asserted) signal is negated during S1. MC68EC020--One-half clock later in S1, the processor asserts AS, indicating that the address on the address bus is valid. State 2 MC68020/EC020--During S2, the processor places the data to be written onto D31-D0. At the end of S2, the processor samples DSACK1/DSACK0. State 3 MC68020/EC020--The processor asserts DS during S3, indicating that the data on the data bus is stable. As long as at least one of the DSACK1/DSACK0 signals is recognized by the end of S2 (meeting the asynchronous input setup time requirement), the cycle terminates one clock later. If DSACK1/DSACK0 is not recognized by the start of S3, the processor inserts wait states instead of proceeding to S4 and S5. To ensure that wait states are inserted, both DSACK1 and DSACK0 must remain negated throughout the asynchronous input setup and hold times around the end of S2. If wait states are added, the processor continues to sample the DSACK1/DSACK0 signals on the falling edges of the clock until one is recognized. The external device uses R/W , DS, SIZ1, SIZ0, A1, and A0 to latch data from the appropriate byte(s) of the data bus (D31-D24, D23-D16, D15-D8, and D7-D0). SIZ1, SIZ0, A1, and A0 select the bytes of the data bus. If it has not already done so, the device asserts DSACK1/DSACK0 to signal that it has successfully stored the data. 5-38 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State 4 MC68020/EC020--The processor issues no new control signals during S4. State 5 MC68020--The processor negates AS and DS during S5. It holds the address and data valid during S5 to provide address hold time for memory systems. R/W , SIZ1, SIZ0, FC2-FC0, and DBEN also remain valid throughout S5. The external device must keep DSACK1/DSACK0 asserted until it detects the negation of AS or DS (whichever it detects first). The device must negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of A S or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next bus cycle. MC68EC020--The processor negates AS and DS during S5. It holds the address and data valid during S5 to provide address hold time for memory systems. R/W , SIZ1, SIZ0, and FC2-FC0 also remain valid throughout S5. The external device must keep DSACK1/DSACK0 asserted until it detects the negation of AS or DS (whichever it detects first). The device must negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of A S or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next bus cycle. 5.3.3 Read-Modify-Write Cycle The read-modify-write cycle performs a read, conditionally modifies the data in the arithmetic logic unit, and may write the data out to memory. In the MC68020/EC020, this operation is indivisible, providing semaphore capabilities for multiprocessor systems. During the entire read-modify-write sequence, the MC68020/EC020 asserts RMC to indicate that an indivisible operation is occurring. The MC68020/EC020 does not issue a BG signal in response to a BR signal during this operation. The TAS, CAS, and CAS2 instructions are the only MC68020/EC020 instructions that utilize read-modify-write operations. Depending on the compare results of the CAS and CAS2 instructions, the write cycle(s) may not occur. Figure 5-29 is a flowchart of the read-modify-write cycle operation. Figure 5-30 is an example timing diagram of a TAS instruction specified in terms of clock periods. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-39 Freescale Semiconductor, Inc. PROCESSOR EXTERNAL DEVICE LOCK BUS 1) ASSERT RMC ADDRESS DEVICE *1) ASSERT ECS/OCS FOR ONE-HALF CLOCK 2) SET R/W TO READ Freescale Semiconductor, Inc... ** 3) DRIVE ADDRESS ON A31-A0 4) 5) 6) 7) *8) DRIVE FUNCTION CODES ON FC2-FC0 DRIVE SIZ1, SIZ0 ASSERT AS ASSERT DS ASSERT DBEN 1) DECODE ADDRESS 2) PLACE DATA ON D31-D0 3) ASSERT DSACK1/DSACK0 ACQUIRE DATA 1) 2) * 3) 4) PRESENT DATA A LATCH DATA NEGATE AS AND DS NEGATE DBEN START DATA MODIFICATION TERMINATE CYCLE 1) REMOVE DATA FROM D31-D0 2) NEGATE DSACK1/DSACK0 IF CAS2 INSTRUCTION AND ONLY ONE OPERAND READ, THEN GO TO A ; IF OPERANDS DO NOT MATCH, THEN GO TO C ; ELSE GO TO B C B START OUTPUT TRANSFER *1) ASSERT ECS/OCS FOR ONE-HALF CLOCK ** 2) DRIVE ADDRESS ON A31-A0 (IF DIFFERENT) 3) 4) 5) *6) 7) 8) DRIVE SIZ1, SIZ0 SET R/W TO WRITE ASSERT AS ASSERT DBEN PLACE DATA ON D31-D0 ASSERT DS ACCEPT DATA 1) DECODE ADDRESS 2) STORE DATA FROM D31-D0 3) ASSERT DSACK1/DSACK0 D TERMINATE OUTPUT TRANSFER 1) NEGATE AS AND DS 2) REMOVE DATA FROM D31-D0 * 3) NEGATE DBEN TERMINATE CYCLE IF CAS2 INSTRUCTION AND ONLY ONE OPERAND WRITTEN, THEN GO TO D ; ELSE GO TO E 1) NEGATE DSACK1/DSACK0 E UNLOCK BUS 1) NEGATE RMC START NEXT CYCLE * This step does not apply to the MC68EC020. ** For the MC68EC020, A23-A0. Figure 5-29. Read-Modify-Write Cycle Flowchart 5-40 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 Si Si S6 S8 S10 S11 S0 CLK *A31-A2 A1 A0 FC2-FC0 SIZ1 Freescale Semiconductor, Inc... SIZ0 R/W RMC ** ECS ** OCS AS DS DSACK1 DSACK0 **DBEN D31-D24 OP3 D23-D16 OP3 D15-8 OP3 OP3 D7-D0 OP3 BERR HALT BG INDIVISIBLE CYCLE NEXT CYCLE * For the MC68EC020, A23-A2. ** This signal does not apply to the MC68EC020. Figure 5-30. Byte Read-Modify-Write Cycle--32-Bit Port (TAS Instruction) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-41 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State 0 MC68020--The processor asserts ECS and OCS in S0 to indicate the beginning of an external operand cycle. The processor also asserts RMC in S0 to identify a readmodify-write cycle. The processor places a valid address on A31-A0 and valid function codes on FC2-FC0. The function codes select the address space for the operation. SIZ1, SIZ0 become valid in S0 to indicate the operand size. The processor drives R/W high for the read cycle. MC68EC020--The processor asserts RMC in S0 to identify a read-modify-write cycle. The processor places a valid address on A23-A0 and valid function codes on FC2- FC0. The function codes select the address space for the operation. SIZ1-SIZ0 become valid in S0 to indicate the operand size. The processor drives R/W high for the read cycle. State 1 MC68020--One-half clock later in S1, the processor asserts AS to indicate that the address on the address bus is valid. The processor also asserts DS during S1. In addition, the ECS (and OCS, if asserted) signal is negated during S1. MC68EC020--One-half clock later in S1, the processor asserts AS to indicate that the address on the address bus is valid. The processor also asserts DS during S1. State 2 MC68020--During S2, the processor asserts DBEN to enable external data buffers. The selected device uses R/W , SIZ1, SIZ0, A1, A0, and DS to place information on the data bus. Any or all of the bytes (D31-D24, D23-D16, D15-D8, and D7-D0) are selected by SIZ1, SIZ0, A1, and A0. Concurrently, the selected device may assert the DSACK1/DSACK0 signals. MC68EC020--During S2, the selected device uses R/W, SIZ1, SIZ0, A1, A0, and DS to place information on the data bus. Any or all of the bytes (D31-D24, D23-D16, D15- D8, and D7-D0) are selected by SIZ1, SIZ0, A1, and A0. Concurrently, the selected device may assert the DSACK1/DSACK0 signals. State 3 MC68020/EC020--As long as at least one of the DSACK1/DSACK0 signals is recognized by the end of S2 (meeting the asynchronous input setup time requirement), data is latched on the next falling edge of the clock, and the cycle terminates. If DSACK1/DSACK0 is not recognized by the start of S3, the processor inserts wait states instead of proceeding to S4 and S5. To ensure that wait states are inserted, both DSACK0 and DSACK1 must remain negated throughout the asynchronous input setup and hold times around the end of S2. If wait states are added, the processor continues to sample the DSACK1/DSACK0 signals on the falling edges of the clock until one is recognized. State 4 MC68020/EC020--At the end of S4, the processor latches the incoming data. 5-42 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. State 5 MC68020--The processor negates AS, DS, and DBEN during S5. If more than one read cycle is required to read in the operand(s), S0-S5 are repeated for each read cycle. When the read cycle(s) are complete, the processor holds the address, R/W , and FC2-FC0 valid in preparation for the write portion of the cycle. The external device keeps its data and DSACK1/DSACK0 signals asserted until it detects the negation of AS or DS (whichever it detects first). The device must remove the data and negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of AS or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next portion of the operation. MC68EC020--The processor negates AS, DS, and DBEN during S5. If more than one read cycle is required to read in the operand(s), S0-S5 are repeated for each read cycle. When the read cycle(s) is complete, the processor holds the address, R/W, and FC2-FC0 valid in preparation for the write portion of the cycle. The external device keeps its data and DSACK1/DSACK0 signals asserted until it detects the negation of AS or DS (whichever it detects first). The device must remove the data and negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of AS or DS. DSACK1/DSACK0 signals that remain asserted beyond this limit may be prematurely detected for the next portion of the operation. Idle States MC68020/EC020--The processor does not assert any new control signals during the idle states, but it may internally begin the modify portion of the cycle at this time. S6- S11 are omitted if no write cycle is required. If a write cycle is required, the R/W signal remains in the read mode until S6 to prevent bus conflicts with the preceding read portion of the cycle; the data bus is not driven until S8. State 6 MC68020--The processor asserts ECS and OCS in S6 to indicate that another external cycle is beginning. The processor drives R/W low for a write cycle. Depending on the write operation to be performed, the address lines may change during S6. MC68EC020--During S6, the processor drives R/W low for a write cycle. Depending on the write operation to be performed, the address lines may change during S6. State 7 MC68020--During S7, the processor asserts AS, indicating that the address on the address bus is valid. The processor also asserts DBEN, which can be used to enable data buffers. In addition, ECS (and OCS, if asserted) is negated during S7. MC68EC020--During S7, the processor asserts AS, indicating that the address on the address bus is valid. State 8 MC68020/EC020--During S8, the processor places the data to be written onto the data bus. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-43 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. State 9 MC68020/EC020--The processor asserts DS during S9, indicating that the data on the data bus is stable. As long as at least one of the DSACK1/DSACK0 signals is recognized by the end of S8 (meeting the asynchronous input setup time requirement), the cycle terminates one clock later. If DSACK1/DSACK0 is not recognized by the start of S9, the processor inserts wait states instead of proceeding to S10 and S11. To ensure that wait states are inserted, both DSACK1 and DSACK0 must remain negated throughout the asynchronous input setup and hold times around the end of S8. If wait states are added, the processor continues to sample DSACK1/DSACK0 signals on the falling edges of the clock until one is recognized. The external device uses R/W , DS, SIZ1, SIZ0, A1, and A0 to latch data from the appropriate section(s) of the data bus (D31-D24, D23-D16, D15-D8, and D7-D0). SIZ1, SIZ0, A1, and A0 select the data bus sections. If it has not already done so, the device asserts DSACK1/DSACK0 when it has successfully stored the data. State 10 MC68020/EC020--The processor issues no new control signals during S10. State 11 MC68020/EC020--The processor negates AS and DS during S11. It holds the address and data valid during S11 to provide address hold time for memory systems. R/W and FC2-FC0 also remain valid throughout S11. If more than one write cycle is required, S6-S11 are repeated for each write cycle. The external device keeps DSACK1/DSACK0 asserted until it detects the negation of AS or D S (whichever it detects first). The device must remove its data and negate DSACK1/DSACK0 within approximately one clock period after sensing the negation of AS or DS. 5.4 CPU SPACE CYCLES FC2-FC0 select user and supervisor program and data areas as listed in Table 2-1. The area selected by FC2-FC0 = 111 is classified as the CPU space. The interrupt acknowledge, breakpoint acknowledge, module operations, and coprocessor communication cycles described in the following paragraphs utilize CPU space. The CPU space type is encoded on A19-A16 during a CPU space operation and indicates the function that the processor is performing. On the MC68020/EC020, four of the encodings are implemented as shown in Figure 5-31. All unused values are reserved by Motorola for future use. 5-44 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. FUNCTION CODE 2 0 BREAKPOINT ACKNOWLEDGE ADDRESS BUS 31 24 23 1 1 1 31 ACCESS LEVEL CONTROL 20 19 1 1 1 1 1 1 INTERRUPT ACKNOWLEDGE 1 1 1 20 19 5 4 16 15 2 1 20 19 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 BKPT # 0 0 0 7 6 0 0 0 0 0 0 0 0 0 0 16 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 31 Freescale Semiconductor, Inc... 16 15 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 31 COPROCESSOR COMMUNICATION 20 19 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 12 CpID MMU REG 5 4 0 0 0 0 0 0 0 0 16 15 1 1 1 0 CP REG 4 3 1 1 1 1 1 1 1 1 1 1 1 LEVEL 0 1 CPU SPACE TYPE FIELD Figure 5-31. MC68020/EC020 CPU Space Address Encoding 5.4.1 Interrupt Acknowledge Bus Cycles When a peripheral device signals the processor (with the IPL2-IPL0 signals) that the device requires service and when the internally synchronized value on these signals indicates a higher priority than the interrupt mask in the status register (or that a transition has occurred in the case of a level 7 interrupt), the processor makes the interrupt a pending interrupt. Refer to Section 6 Exception Processing for details on the recognition of interrupts. The MC68020/EC020 takes an interrupt exception for a pending interrupt within one instruction boundary (after processing any other pending exception with a higher priority). The following paragraphs describe the various kinds of interrupt acknowledge bus cycles that can be executed as part of interrupt exception processing. 5.4.1.1 INTERRUPT ACKNOWLEDGE CYCLE--TERMINATED NORMALLY. When the MC68020/EC020 processes an interrupt exception, it performs an interrupt acknowledge cycle to obtain the number of the vector that contains the starting location of the interrupt service routine. Some interrupting devices have programmable vector registers that contain the interrupt vectors for the routines they use. The following paragraphs describe the interrupt acknowledge cycle for these devices. Other interrupting conditions or devices cannot supply a vector number and use the autovector cycle described in 5.4.1.2 Autovector Interrupt Acknowledge Cycle. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-45 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The interrupt acknowledge cycle is a read cycle. It differs from the read cycle described in 5.3.1 Read Cycle in that it accesses the CPU address space. Specifically, the differences are: 1. FC2-FC0 are set 111 for CPU address space. 2. A3, A2, and A1 are set to the interrupt request level (the inverted values of IPL2, IPL1, and IPL0, respectively). 3. The CPU space type field (A19-A16) is set to 1111, the interrupt acknowledge code. 4. Other address signals (A31-A20, A15-A4, and A0 for the MC68020; A23-A20, A15-A4, and A0 for the MC68EC020) are set to one. The responding device places the vector number on the data bus during the interrupt acknowledge cycle. Beyond this, the cycle is terminated normally with DSACK1/DSACK0. Figure 5-32 is the flowchart of the interrupt acknowledge cycle. Figure 5-33 shows the timing for an interrupt acknowledge cycle terminated with DSACK1/DSACK0. INTERRUPTING DEVICE PROCESSOR ACKNOWLEDGE INTERRUPT REQUEST INTERRUPT 1) INTERRUPT PENDING CONDITION (IPEND FOR MC68020) RECOGNIZED BY CURRENT INSTRUCTION--WAIT FOR INSTRUCTION BOUNDARY. 2) SET R/W TO READ 3) SET FUNCTION CODE TO CPU SPACE 4) PLACE INTERRUPT LEVEL ON A1, A2, AND A3. TYPE FIELD = IACK 5) SET SIZE TO BYTE * 6) NEGATE IPEND 7) ASSERT AS AND DS PROVIDE VECTOR INFORMATION 1) PLACE VECTOR NUMBER ON LEAST SIGNIFICANT BYTE OF DATA PORT (DEPENDS ON PORT SIZE) 2) ASSERT DSACK1/DSACK0 OR ASSERT AVEC FOR AUTOMATIC GENERATION OF VECTOR NUMBER ACQUIRE VECTOR NUMBER 1) LATCH VECTOR NUMBER 2) NEGATE AS AND DS RELEASE CONTINUE INTERRUPT EXCEPTION PROCESSING 1) REMOVE VECTOR NUMBER FROM DATA BUS 2) NEGATE DSACK1/DSACK0 * This step does not apply to the MC68EC020. Figure 5-32. Interrupt Acknowledge Cycle Flowchart 5-46 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 CLK *A31-A4 A3-A1 INTERRUPT LEVEL A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D24-D31 VECTOR # FROM 8-BIT PORT D23-D16 VECTOR # FROM 16-BIT PORT D7-D0 VECTOR # FROM 32-BIT PORT IPL2-IPL0 ** IPEND INTERRUPT ACKNOWLEDGE READ CYCLE WRITE STACK * For the MC68EC020, A23-A4. ** This signal does not apply to the MC68EC020. Figure 5-33. Interrupt Acknowledge Cycle Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-47 Freescale Semiconductor, Inc. 5.4.1.2 AUTOVECTOR INTERRUPT ACKNOWLEDGE CYCLE. When the interrupting device cannot supply a vector number, it requests an automatically generated vector or autovector. Instead of placing a vector number on the data bus and asserting DSACK1/DSACK0, the device asserts AVEC to terminate the cycle. The DSACK1/DSACK0 signals may not be asserted during an interrupt acknowledge cycle terminated by AVEC. Freescale Semiconductor, Inc... The vector number supplied in an autovector operation is derived from the interrupt level of the current interrupt. When AVEC is asserted instead of DSACK1/DSACK0 during an interrupt acknowledge cycle, the MC68020/EC020 ignores the state of the data bus and internally generates the vector number, the sum of the interrupt level plus 24 ($18). Seven distinct autovectors, which correspond to the seven levels of interrupt available with IPL2- IPL0, can be used. Figure 5-34 shows the timing for an autovector operation. 5.4.1.3 SPURIOUS INTERRUPT CYCLE. When a device does not respond to an interrupt acknowledge cycle with AVEC or DSACK1/DSACK0, the external logic typically returns BERR. In this case, the MC68020/EC020 automatically generates 24, the spurious interrupt vector number. If HALT is also asserted, the processor retries the cycle. 5-48 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 CLK * A31-A4 A1-A3 INTERRUPT LEVEL A0 FC2-FC0 Freescale Semiconductor, Inc... SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 IPL2-IPL0 AVEC INTERRUPT ACKNOWLEDGE AUTOVECTORED READ CYCLE WRITE STACK * For the MC68EC020, A23-A4. ** This signal does not apply to the MC68EC020. Figure 5-34. Autovector Operation Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-49 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... 5.4.2 Breakpoint Acknowledge Cycle The breakpoint acknowledge cycle is generated by the execution of a BKPT instruction. The breakpoint acknowledge cycle allows the external hardware to provide an instruction word directly into the instruction pipeline as the program executes. This cycle accesses the CPU space with a type field of zero and provides the breakpoint number specified by the instruction on address lines A4-A2. If the external hardware terminates the cycle with DSACK1/DSACK0, the data on the bus (an instruction word) is inserted into the instruction pipe, replacing the breakpoint opcode, and is executed after the breakpoint acknowledge cycle completes. The BKPT instruction requires a word to be transferred so that if the first bus cycle accesses an 8-bit port, a second cycle is required. If the external logic terminates the breakpoint acknowledge cycle with BERR (i.e., no instruction word available), the processor takes an illegal instruction exception. Figure 5-35 is a flowchart of the breakpoint acknowledge cycle. Figure 5-36 shows the timing for a breakpoint acknowledge cycle that returns an instruction word. Figure 5-37 shows the timing for a breakpoint acknowledge cycle that signals an exception. PROCESSOR EXTERNAL DEVICE BREAKPOINT ACKNOWLEDGE 1) 2) 3) 4) 5) 6) SET R/W TO READ SET FUNCTION CODE TO CPU SPACE PLACE CPU SPACE TYPE 0 ON A19-A16 PLACE BREAKPOINT NUMBER ON A4-A2 SET SIZE TO WORD ASSERT AS AND DS 1) PLACE REPLACEMENT OPCODE ON DATA BUS 2) ASSERT DSACK1/DTACK0 OR 1) ASSERT BERR TO INITIATE EXCEPTION PROCESSING IF DSACK1/DSACK0 ASSERTED: 1) LATCH DATA 2) NEGATE AS AND DS 3) GO TO A IF BERR ASSERTED: 1) NEGATE AS AND DS 2) GO TO B A B 1) PLACE LATCHED DATA IN INSTRUCTION PIPELINE 2) CONTINUE PROCESSING SLAVE NEGATES DSACK1/DSACK0 OR BERR 1) INITIATE ILLEGAL INSTRUCTION PROCESSING Figure 5-35. Breakpoint Acknowledge Cycle Flowchart 5-50 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 CLK *A31-A20 A19-A16 (0000) BREAKPOINT ENCODING A15-A2 BREAKPOINT NUMBER A1-A0 FC2-FC0 Freescale Semiconductor, Inc... WORD SIZ1 SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D23-D16 D15-D8 D7-D0 BERR HALT READ CYCLE BREAKPOINT ACKNOWLEDGE INSTRUCTION WORD FETCH FETCHED INSTRUCTION EXECUTION Figure 5-36. Breakpoint Acknowledge Cycle Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-51 Freescale Semiconductor, Inc. S0 S2 Sw Sw Sw S4 S0 S2 S4 CLK *A31-A0 FC2-FC0 SIZ1-SIZ0 Freescale Semiconductor, Inc... R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 BERR HALT READ WITH BERR ASSERTED INTERNAL PROCESSING STACK WRITE * For the MC68EC020, A23-A0. ** This signal does not apply to the MC68EC020. Figure 5-37. Breakpoint Acknowledge Cycle Timing (Exception Signaled) 5-52 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.4.3 Coprocessor Communication Cycles Freescale Semiconductor, Inc... The MC68020/EC020 coprocessor interface provides instruction-oriented communication between the processor and as many as eight coprocessors. Coprocessor accesses use the MC68020/EC020 bus protocol except that the address bus supplies access information rather than a 32-bit address. The CPU space type field (A19-A16) for a coprocessor operation is 0010. A15-A13 contain the coprocessor identification number (CpID), and A5-A0 specify the coprocessor interface register to be accessed. The memory management unit of an MC68020/EC020 system is always identified by a CpID of zero and has an extended register select field (A7-A0) in CPU space 0001 for use by the CALLM and RTM access level checking mechanism. Refer to Section 9 Applications Information for more details. 5.5 BUS EXCEPTION CONTROL CYCLES The MC68020/EC020 bus architecture requires assertion of DSACK1/DSACK0 from an external device to signal that a bus cycle is complete. DSACK1/DSACK0 or AVEC is not asserted if: * The external device does not respond, * No interrupt vector is provided, or * Various other application-dependent errors occur. External circuitry can assert B E R R when no device responds by asserting DSACK1/DSACK0 or A V E C within an appropriate period of time after the processor asserts AS. Assertion of BERR allows the cycle to terminate and the processor to enter exception processing for the error condition. HALT is also used for bus exception control. HALT can be asserted by an external device for debugging purposes to cause single bus cycle operation or can be asserted in combination with BERR to cause a retry of a bus cycle in error. To properly control termination of a bus cycle for a retry or a bus error condition, DSACK1/DSACK0, BERR, and HALT can be asserted and negated with the rising edge of the MC68020/EC020 clock. This procedure ensures that when two signals are asserted simultaneously, the required setup time (#47A) and hold time (#47B) for both of them is met for the same falling edge of the processor clock. (Refer to Section 10 Electrical Characteristics for timing requirements.) This or some equivalent precaution should be designed into the external circuitry that provides these signals. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-53 Freescale Semiconductor, Inc. The acceptable bus cycle terminations for asynchronous cycles are summarized in relation to DSACK1/DSACK0 assertion as follows (case numbers refer to Table 5-8): Normal Termination: DSACK1/DSACK0 is asserted; BERR and HALT remain negated (case 1). Freescale Semiconductor, Inc... Halt Termination: HALT is asserted at same time or before DSACK1/DSACK0, and BERR remains negated (case 2). Bus Error Termination: BERR is asserted in lieu of, at the same time, or before DSACK1/DSACK0 (case 3) or after DSACK1/DSACK0 (case 4), and HALT remains negated; BERR is negated at the same time or after DSACK1/DSACK0. Retry Termination: HALT and BERR are asserted in lieu of, at the same time, or before DSACK1/DSACK0 (case 5) or after DSACK1/DSACK0 (case 6); BERR is negated at the same time or after DSACK1/DSACK0; HALT may be negated at the same time or after BERR. Table 5-8. DSACK1/DSACK0 , BERR , HALT Assertion Results Asserted on Rising Edge of State Case No. Control Signal n n+2 Result 1 DSACK1/DSACK0 BERR HALT A N N S N X Normal cycle terminate and continue. 2 DSACK1/DSACK0 BERR HALT A N A/S S N S Normal cycle terminate and halt. Continue when HALT negated. 3 DSACK1/DSACK0 BERR HALT N/A A N X S N Terminate and take bus error exception, possibly deferred. 4 DSACK1/DSACK0 BERR HALT A N N X A N Terminate and take bus error exception, possibly deferred. 5 DSACK1/DSACK0 BERR HALT N/A A A/S X S S Terminate and retry when HALT negated. 6 DSACK1/DSACK0 BERR HALT A N N X A A Terminate and retry when HALT negated. Legend: n--The number of current even bus state (e.g., S2, S4, etc.) A--Signal is asserted in this bus state N--Signal is not asserted and/or remains negated in this bus state X--Don't care S--Signal was asserted in previous state and remains asserted in this state 5-54 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 5-8 lists various combinations of control signal sequences and the resulting bus cycle terminations. To ensure predictable operation, BERR and HALT should be negated according to parameters #28 and #57 in Section 10 Electrical Characteristics. DSACK1/DSACK0, BERR, and HALT may be negated after AS. If DSACK1/DSACK0 or BERR remain asserted into S2 of the next bus cycle, that cycle may be terminated prematurely. Freescale Semiconductor, Inc... Example A: A system uses a watchdog timer to terminate accesses to an unpopulated address space. The timer asserts BERR after timeout (case 3). Example B: A system uses error detection and correction on RAM contents. The designer may: 1. Delay DSACK1/DSACK0 assertion until data is verified and assert BERR and HALT simultaneously to indicate to the processor to automatically retry the error cycle (case 5) or, if data is valid, assert DSACK1/DSACK0 (case 1). 2. Delay DSACK1/DSACK0 assertion until data is verified and assert BERR with or without DSACK1/DSACK0 if data is in error (case 3). This configuration initiates exception processing for software handling of the condition. 3. Assert DSACK1/DSACK0 prior to data verification. If data is invalid, BERR is asserted on the next clock cycle (case 4). This configuration initiates exception processing for software handling of the condition. 4. Assert DSACK1/DSACK0 prior to data verification; if data is invalid, assert BERR and HALT on the next clock cycle (case 6). The memory controller can then correct the RAM prior to or during the automatic retry. 5.5.1 Bus Errors The BERR signal can be used to abort the bus cycle and the instruction being executed. BERR takes precedence over DSACK1/DSACK0, provided it meets the timing constraints described in Section 10 Electrical Characteristics. If BERR does not meet these constraints, it may cause unpredictable operation of the MC68020/EC020. If BERR remains asserted into the next bus cycle, it may cause incorrect operation of that cycle. When BERR is issued to terminate a bus cycle, the MC68020/EC020 may enter exception processing immediately following the bus cycle, or it may defer processing the exception. The instruction prefetch mechanism requests instruction words from the bus controller and the instruction cache before it is ready to execute them. If a bus error occurs on an instruction fetch, the processor does not take the exception until it attempts to use that instruction word. Should an intervening instruction cause a branch or should a task switch occur, the bus error exception does not occur. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-55 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... BERR is recognized during a bus cycle in any of the following cases: 1. DSACK1/DSACK0 and HALT are negated and BERR is asserted. 2. HALT and BERR are negated and DSACK1/DSACK0 is asserted. BERR is then asserted within one clock cycle (HALT remains negated). 3. BERR and HALT are asserted (see 5.5.2 Retry Operation). When the processor recognizes a bus error condition, it terminates the current bus cycle in the normal way. Figure 5-38 shows the timing of a bus error for the case in which DSACK1/DSACK0 is not asserted. Figure 5-39 shows the timing for a bus error for the case in which BERR is asserted after DSACK1/DSACK0. Exceptions are taken in both cases. (Refer to Section 6 Exception Processing for details of bus error exception processing.) When BERR is asserted during a read cycle that supplies an instruction to the on-chip cache, the instruction in the cache is marked invalid. When BERR is asserted after DSACK1/DSACK0, B E R R must be asserted within parameter #48 (refer to Section 10 Electrical Characteristics) for purely asynchronous operation, or it must be asserted and remain stable during the sample window, defined by parameters #27A and #47B, around the next falling edge of the clock after DSACK1/DSACK0 is recognized. If BERR is not stable at this time, the processor may exhibit erratic behavior. In this case, data may be present on the bus, but may not be valid. This sequence may be used by systems that have memory error detection and correction logic and by external cache memories. 5.5.2 Retry Operation When BERR and HALT are asserted simultaneously by an external device during a bus cycle, the processor enters the retry sequence. A delayed retry similar to the delayed BERR signal described previously can also occur. The processor terminates the bus cycle, negates the control signals (AS, DS, R/W, SIZ1, SIZ0, RMC, and, for the MC68020 only, ECS and OCS), and does not begin another bus cycle until the BERR and HALT signals have been negated by external logic. After a synchronization delay, the processor retries the previous cycle using the same access information (address, function code, size, etc.) The BERR signal should be negated before S2 of the read cycle to ensure correct operation of the retried cycle. Figure 5-40 shows a late retry operation of a cycle. The processor retries any read or write cycle of a read-modify-write operation separately; RMC remains asserted during the entire retry sequence. Asserting BR along with BERR and HALT provides a relinquish and retry operation. The MC68020/EC020 does not relinquish the bus during a read-modify-write operation. Any device that requires the processor to give up the bus and retry a bus cycle during a readmodify-write cycle must assert BERR and BR only (HALT must not be included). The bus error handler software should examine the read-modify-write bit in the special status word (refer to Section 6 Exception Processing) and take the appropriate action to resolve this type of fault when it occurs. 5-56 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 S0 S2 CLK * A31-A20 A19-A16 (0000) BREAKPOINT ENCODING A15-A2 BREAKPOINT NUMBER A1-A0 FC2-FC0 CPU SPACE Freescale Semiconductor, Inc... SIZ1 WORD SIZ0 R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D24 D23-D16 D15-D8 D7-D0 BERR HALT BREAKPOINT ACKNOWLEDGE BUS ERROR FETCH READ CYCLE * ** EXCEPTION STACKING For the MC68EC020, A23-A20. This signal does not apply to the MC68EC020. Figure 5-38. Bus Error without DSACK1/DSACK0 MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-57 Freescale Semiconductor, Inc. S0 S2 Sw Sw S4 S0 S2 S4 CLK *A31-A0 FC2-FC0 SIZ1-SIZ0 Freescale Semiconductor, Inc... R/W ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 IPL2-IPL0 BERR HALT WRITE WITH BERR ASSERTED INTERNAL PROCESSING STACK WRITE * For the MC68EC020, A23-A0. ** This signal does not apply to the MC68EC020. Figure 5-39. Late Bus Error with 5-58 DSACK1/DSACK0 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 Sw S4 S0 S2 S4 CLK *A31-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... ** ECS ** OCS AS DS DSACK1 DSACK0 DATA BUS NOT DRIVEN D31-D0 BERR HALT WRITE CYCLE RETRY SIGNALED HALT RETRY CYCLE * For the MC68EC020, A23-A0. ** This signal does not apply to the MC68EC020. Figure 5-40. Late Retry MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-59 Freescale Semiconductor, Inc. 5.5.3 Halt Operation Freescale Semiconductor, Inc... When HALT is asserted and BERR is not asserted, the MC68020/EC020 halts external bus activity at the next bus cycle boundary. HALT by itself does not terminate a bus cycle. Negating and reasserting HALT in accordance with the correct timing requirements provides a single-step (bus cycle to bus cycle) operation. The HALT signal affects external bus cycles only; thus, a program that resides in the instruction cache and does not require use of the external bus may continue executing unaffected by HALT. The single-cycle mode allows the user to proceed through (and debug) external processor operations, one bus cycle at a time. Figure 5-41 shows the timing requirements for a single-cycle operation. Since the occurrence of a bus error while HALT is asserted causes a retry operation, the user must anticipate retry cycles while debugging in the single-cycle mode. The single-step operation and the software trace capability allow the system debugger to trace single bus cycles, single instructions, or changes in program flow. These processor capabilities, along with a software debugging package, give complete debugging flexibility. When the processor completes a bus cycle with the HALT signal asserted, the data bus is placed in the high-impedance state, and the bus control signals (AS, DS, and, for the MC68020 only, ECS and OCS) are negated (not placed in the high-impedance state); A31-A0 for the MC68020 or A23-A0 for the MC68EC020, FC2-FC0, SIZ1, SIZ0, and R/W remain in the same state. The halt operation has no effect on bus arbitration (refer to 5.7 Bus Arbitration). When bus arbitration occurs while the MC68020/EC020 is halted, the address and control signals (A31-A0, FC2-FC0, SIZ1, SIZ0, R/W, AS, DS, and, for the MC68020 only, ECS and OCS) are also placed in the high-impedance state. Once bus mastership is returned to the MC68020/EC020, if HALT is still asserted, A31-A0 for the MC68020 or A23-A0 for the MC68EC020, FC2-FC0, SIZ1, SIZ0, and R/W are again driven to their previous states. The MC68020/EC020 does not service interrupt requests while it is halted (although the MC68020 may assert the IPEND signal as appropriate). 5.5.4 Double Bus Fault When a bus error or an address error occurs during the exception processing sequence for a previous bus error, a previous address error, or a reset exception, a double bus fault occurs. For example, the processor attempts to stack several words containing information about the state of the machine while processing a bus error exception. If a bus error exception occurs during the stacking operation, the second error is considered a double bus fault. When a double bus fault occurs, the processor halts and asserts HALT. Only an external reset operation can restart a halted processor. However, bus arbitration can still occur (refer to 5.7 Bus Arbitration). A second bus error or address error that occurs after exception processing has completed (during the execution of the exception handler routine or later) does not cause a double bus fault. A bus cycle that is retried does not constitute a bus error or contribute to a double bus fault. The processor continues to retry the same bus cycle as long as the external hardware requests it. 5-60 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 S4 CLK *A31-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 BERR HALT HALT (BUS ARBITRATION PERMITTED WHILE THE PROCESSOR IS HALTED) READ READ * For the MC68EC020, A23-A0. ** This signal does not apply to the MC68EC020. Figure 5-41. Halt Operation Timing MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-61 Freescale Semiconductor, Inc. 5.6 BUS SYNCHRONIZATION Freescale Semiconductor, Inc... The MC68020/EC020 overlaps instruction execution--that is, during bus activity for one instruction, instructions that do not use the external bus can be executed. Due to the independent operation of the on-chip cache relative to the operation of the bus controller, many subsequent instructions can be executed, resulting in seemingly nonsequential instruction execution. When this is not desired and the system depends on sequential execution following bus activity, the NOP instruction can be used. The NOP instruction forces instruction and bus synchronization by freezing instruction execution until all pending bus cycles have completed. An example of the use of the NOP instruction for this purpose is the case of a write operation of control information to an external register in which the external hardware attempts to control program execution based on the data that is written with the conditional assertion of BERR. Since the MC68020/EC020 cannot process the bus error until the end of the bus cycle, the external hardware has not successfully interrupted program execution. To prevent a subsequent instruction from executing until the external cycle completes, the NOP instruction can be inserted after the instruction causing the write. In this case, bus error exception processing proceeds immediately after the write and before subsequent instructions are executed. This is an irregular situation, and the use of the NOP instruction for this purpose is not required by most systems. 5.7 BUS ARBITRATION The bus design of the MC68020/EC020 provides for a single bus master at any one time: either the processor or an external device. One or more of the external devices on the bus can have the capability of becoming bus master. Bus arbitration is the protocol by which an external device becomes bus master; the bus controller in the MC68020/EC020 manages the bus arbitration signals so that the processor has the lowest priority. Bus arbitration differs in the MC68020 and MC68EC020 due to the absence of BGACK in the MC68EC020. Because of this difference, bus arbitration of the MC68020 and MC68EC020 is discussed separately. External devices that need to obtain the bus must assert the bus arbitration signals in the sequences described in 5.7.1 MC68020 Bus Arbitration or 5.7.2 MC68EC020 Bus Arbitration. Systems having several devices that can become bus master require external circuitry to assign priorities to the devices, so that when two or more external devices attempt to become bus master at the same time, the one having the highest priority becomes bus master first. 5-62 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.7.1 MC68020 Bus Arbitration Freescale Semiconductor, Inc... The sequence of the MC68020 bus arbitration protocol is as follows: 1. An external device asserts the BR signal. 2. The processor asserts the BG signal to indicate that the bus will become available at the end of the current bus cycle. 3. The external device asserts the BGACK signal to indicate that it has assumed bus mastership. BR may be issued any time during a bus cycle or between cycles. BG is asserted in response to BR; it is usually asserted as soon as BR has been synchronized and recognized, except when the MC68020 has made an internal decision to execute a bus cycle. Then, the assertion of BG is deferred until the bus cycle has begun. Additionally, BG is not asserted until the end of a read-modify-write operation (when RMC is negated) in response to a BR signal. When the requesting device receives BG and more than one external device can be bus master, the requesting device should begin whatever arbitration is required. The external device asserts BGACK when it assumes bus mastership, and maintains BGACK during the entire bus cycle (or cycles) for which it is bus master. The following conditions must be met for an external device to assume mastership of the bus through the normal bus arbitration procedure: * The external device must have received BG through the arbitration process. * AS must be negated, indicating that no bus cycle is in progress, and the external device must ensure that all appropriate processor signals have been placed in the high-impedance state (by observing specification #7 in Section 10 Electrical Specifications). * The termination signal (DSACK1/DSACK0) for the most recent cycle must have been negated, indicating that external devices are off the bus (optional, refer to 5.7.1.3 Bus Grant Acknowledge (MC68020)). * BGACK must be inactive, indicating that no other bus master has claimed ownership of the bus. Figure 5-42 is a flowchart of MC68020 bus arbitration for a single device. Figure 5-43 is a timing diagram for the same operation. This technique allows processing of bus requests during data transfer cycles. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-63 Freescale Semiconductor, Inc. PROCESSOR REQUESTING DEVICE REQUEST THE BUS 1) ASSERT BR GRANT BUS ARBITRATION 1) ASSERT BG ACKNOWLEDGE BUS MASTERSHIP 1) EXTERNAL ARBITRATION DETERMINES NEXT BUS MASTER 2) NEXT BUS MASTER WAITS FOR CURRENT CYCLE TO COMPLETE 3) NEXT BUS MASTER ASSERTS BGACK TO BECOME NEW MASTER 4) BUS MASTER NEGATES BR TERMINATE ARBITRATION Freescale Semiconductor, Inc... 1) NEGATE BG AND WAIT FOR BGACK TO BE NEGATED OPERATE AS BUS MASTER 1) PERFORM DATA TRANSFERS (READ AND WRITE CYCLES) RE-ARBITRATE OR RESUME PROCESSOR OPERATION RELEASE BUS MASTERSHIP 1) NEGATE BGACK Figure 5-42. MC68020 Bus Arbitration Flowchart for Single Request The timing diagram (see Figure 5-43) shows that BR is negated at the time that BGACK is asserted. This type of operation applies to a system consisting of the processor and one device capable of bus mastership. In a system having a number of devices capable of bus mastership, the BR line from each device can be wire-ORed to the processor. In such a system, more than one bus request can be asserted simultaneously. The timing diagram in Figure 5-43 shows that BG is negated a few clock cycles after the transition of BGACK. However, if bus requests are still pending after the negation of BG, the processor asserts another BG within a few clock cycles after it was negated. This additional assertion of BG allows external arbitration circuitry to select the next bus master before the current bus master has finished with the bus. The following paragraphs provide additional information about the three steps in the arbitration process. Bus arbitration requests are recognized during normal processing, RESET assertion, HALT assertion, and when the processor has halted due to a double bus fault. 5-64 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 CLK A31-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... ECS OCS AS DS DSACK1 DSACK0 DBEN D31-D0 BR BG BGACK PROCESSOR DMA DEVICE PROCESSOR Figure 5-43. MC68020 Bus Arbitration Operation Timing for Single Request MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-65 Freescale Semiconductor, Inc. 5.7.1.1 BUS REQUEST (MC68020). External devices capable of becoming bus masters request the bus by asserting BR. BR can be a wire-ORed signal (although it need not be constructed from open-collector devices) that indicates to the processor that some external device requires control of the bus. The processor is at a lower bus priority level than the external device and relinquishes the bus after it has completed the current bus cycle (if one has started). Freescale Semiconductor, Inc... If no BGACK is received while BR is asserted, the processor remains bus master once BR is negated. This prevents unnecessary interference with ordinary processing if the arbitration circuitry inadvertently responds to noise or if an external device determines that it no longer requires use of the bus before it has been granted mastership. 5.7.1.2 BUS GRANT (MC68020). The processor asserts BG as soon as possible after receipt of the bus request. BG assertion immediately follows internal synchronization except during a read-modify-write cycle or follows an internal decision to execute a bus cycle. During a read-modify-write cycle, the processor does not assert BG until the entire operation has completed. RMC is asserted to indicate that the bus is locked. In the case of an internal decision to execute another bus cycle, BG is deferred until the bus cycle has begun. BG may be routed through a daisy-chained network or through a specific priority-encoded network. The processor allows any type of external arbitration that follows the protocol. 5.7.1.3 BUS GRANT ACKNOWLEDGE (MC68020). Upon receiving BG, the requesting device waits until AS, DSACK1/DSACK0, and BGACK are negated before asserting its own BGACK. The negation of AS indicates that the previous master releases the bus after specification #7 (refer to Section 10 Electrical Characteristics). The negation of DSACK1/DSACK0 indicates that the previous slave has completed its cycle with the previous master. Note that in some applications, DSACK1/DSACK0 might not be used in this way. General-purpose devices are connected to be dependent only on AS. When BGACK is asserted, the device is the bus master until it negates BGACK. BGACK should not be negated until all bus cycles required by the alternate bus master have been completed. Bus mastership terminates at the negation of BGACK. The BR from the granted device should be negated after BGACK is asserted. If another BR is still pending after the assertion of BGACK, another BG is asserted within a few clocks of the negation of the the first BG, as described in 5.7.1.4 Bus Arbitration Control (MC68020). Note that the processor does not perform any external bus cycles before it reasserts BG in this case. 5-66 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.7.1.4 BUS ARBITRATION CONTROL (MC68020). The bus arbitration control unit in the MC68020 is implemented with a finite state machine. As discussed previously, all asynchronous inputs to the MC68020 are internally synchronized in a maximum of two cycles of the processor clock. As shown in Figure 5-44, input signals labeled R and A are internally synchronized versions of the BR and BGACK signals, respectively. The BG output is labeled G, and the internal high-impedance control signal is labeled T. If T is true, the address, data, and control buses are placed in the high-impedance state after the next rising edge following the negation of AS and RMC. All signals are shown in positive logic (active high), regardless of their true active voltage level. Freescale Semiconductor, Inc... RA XA RA GT STATE 0 RA RA GT GT STATE 4 STATE 1 XX XX RX GT STATE 3 RA XA GT GT RX STATE 2 RA RA STATE 5 GT XX STATE 6 RA R--BUS REQUEST A--BUS GRANT ACKNOWLEDGE G--BUS GRANT T--THREE-STATE CONTROL TO BUS CONTROL LOGIC X--DON'T CARE NOTE: The BG output will not be asserted while RMC is asserted. Figure 5-44. MC68020 Bus Arbitration State Diagram MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-67 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State changes occur on the next rising edge of the clock after the internal signal is recognized as valid. The BG signal transitions on the falling edge of the clock after a state is reached during which G changes. The bus control signals (controlled by T) are driven by the processor immediately following a state change when bus mastership is returned to the MC68020. State 0, at the top center of the diagram, in which both G and T are negated, is the state of the bus arbiter while the processor is bus master. Request R and acknowledge A keep the arbiter in state 0 as long as they are both negated. When a request R is received, both grant G and signal T are asserted (in state 1 at the top left). The next clock causes a change to state 2, at the lower left, in which G and T are held. The bus arbiter remains in that state until acknowledge A is asserted or request R is negated. Once either occurs, the arbiter changes to the center state, state 3, and negates grant G. The next clock takes the arbiter to state 4, at the upper right, in which grant G remains negated and signal T remains asserted. With acknowledge A asserted, the arbiter remains in state 4 until A is negated or request R is again asserted. When A is negated, the arbiter returns to the original state, state 0, and negates signal T. This sequence of states follows the normal sequence of signals for relinquishing the bus to an external bus master. Other states apply to other possible sequences of combinations of R and A. The MC68020 does not allow arbitration of the external bus during the read-modify-write sequence. For the duration of this sequence, the MC68020 ignores the BR input. If mastership of the MC68020 bus is required during a read-modify-write operation, BERR must be used to abort the read-modify-write sequence. The bus arbitration sequence while the bus is inactive (i.e., executing internal operations such as a multiply instruction) is shown in Figure 5-45. 5-68 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S4 S0 CLK A31-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... ECS OCS AS DS DSACK1 DSACK0 DBEN D31-D0 BR BG BGACK PROCESSOR BUS INACTIVE (ARBITRATION PERMITTED WHILE THE PROCESSOR IS INACTIVE OR HALTED) ALTERNATE MASTER PROCESSOR Figure 5-45. MC68020 Bus Arbitration Operation Timing--Bus Inactive MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-69 Freescale Semiconductor, Inc. 5.7.2 MC68EC020 Bus Arbitration Freescale Semiconductor, Inc... The sequence of the MC68EC020 bus arbitration protocol is as follows: 1. An external device asserts the BR signal. 2. The processor asserts the BG signal to indicate that the bus will become available at the end of the current bus cycle. 3. The external device asserts the BR signal throughout its bus mastership. BR may be issued any time during a bus cycle or between cycles. BG is asserted in response to BR; it is usually asserted as soon as BR has been synchronized and recognized, except when the MC68020 has made an internal decision to execute a bus cycle. Then, the assertion of BG is deferred until the bus cycle has begun. Additionally, BG is not asserted until the end of a read-modify-write operation (when RMC is negated) in response to a BR signal. When the requesting device receives BG and more than one external device can be bus master, the requesting device should begin whatever arbitration is required. The external device continues to assert BR when it assumes bus mastership, and maintains BR during the entire bus cycle (or cycles) for which it is bus master. The following conditions must be met for an external device to assume mastership of the bus through the normal bus arbitration procedure: * The external device must have received BG through the arbitration process. * AS must be negated, indicating that no bus cycle is in progress, and the external device must ensure that all appropriate processor signals have been placed in the high-impedance state (by observing specification #7 in Section 10 Electrical Specifications). * The termination signal (DSACK1/DSACK0) for the most recent cycle must have been negated, indicating that external devices are off the bus. * No other bus master has claimed ownership of the bus. Figure 5-46 is a flowchart of MC68EC020 bus arbitration for a single device. Figure 5-47 is a timing diagram for the same operation. This technique allows processing of bus requests during data transfer cycles. Bus arbitration requests are recognized during normal processing, RESET assertion, HALT assertion, and when the processor has halted due to a double bus fault. 5-70 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. PROCESSOR REQUESTING DEVICE REQUEST THE BUS GRANT BUS ARBITRATION 1) ASSERT BR 1) ASSERT BG ACKNOWLEDGE BUS MASTERSHIP OPERATE AS BUS MASTER Freescale Semiconductor, Inc... 1) EXTERNAL ARBITRATION DETERMINES NEXT BUS MASTER 2) NEXT BUS MASTER WAITS FOR CURRENT CYCLE TO COMPLETE 3) PERFORM DATA TRANSFERS (READ AND WRITE CYCLES) RE-ARBITRATE OR RESUME PROCESSOR OPERATION RELEASE BUS MASTERSHIP 1) NEGATE BR Figure 5-46. MC68EC020 Bus Arbitration Flowchart for Single Request 5.7.2.1 BUS REQUEST (MC68EC020). External devices capable of becoming bus masters request the bus by asserting BR. BR can be a wire-ORed signal (although it need not be constructed from open-collector devices) that indicates to the processor that some external device requires control of the bus. The processor is at a lower bus priority level than the external device and relinquishes the bus after it has completed the current bus cycle (if one has started). BR remains asserted throughout the external device's bus mastership. 5.7.2.2 BUS GRANT (MC68EC020). The processor asserts BG as soon as possible after receipt of the bus request. BG assertion immediately follows internal synchronization except during a read-modify-write cycle or follows an internal decision to execute a bus cycle. During a read-modify-write cycle, the processor does not assert BG until the entire operation has completed. RMC is asserted to indicate that the bus is locked. In the case of an internal decision to execute another bus cycle, BG is deferred until the bus cycle has begun. BG may be routed through a daisy-chained network or through a specific priority-encoded network. The processor allows any type of external arbitration that follows the protocol. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-71 Freescale Semiconductor, Inc. S0 S2 S4 S0 S2 CLK A23-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... AS DS DSACK1 DSACK0 D31-D0 BR BG PROCESSOR DMA DEVICE PROCESSOR Figure 5-47. MC68EC020 Bus Arbitration Operation Timing for Single Request 5-72 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 5.7.2.3 BUS ARBITRATION CONTROL (MC68EC020). The bus arbitration control unit in the MC68EC020 is implemented with a finite state machine. As discussed previously, all asynchronous inputs to the MC68EC020 are internally synchronized in a maximum of two cycles of the processor clock. As shown in Figure 5-48, the input signal labeled R is an internally synchronized version of the BR signal. The BG output is labeled G, and the internal high-impedance control signal is labeled T. If T is true, the address, data, and control buses are placed in the highimpedance state after the next rising edge following the negation of AS and RMC. All signals are shown in positive logic (active high), regardless of their true active voltage level. Freescale Semiconductor, Inc... R R GT STATE 0 R GT STATE 4 GT STATE1 X R GT STATE 3 GT STATE 2 R X R GT STATE 5 R GT STATE 6 X R R--BUS REQUEST G--BUS GRANT T --THREE-STATE CONTROL TO BUS CONTROL LOGIC X--DON'T CARE Figure 5-48. MC68EC020 Bus Arbitration State Diagram MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-73 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... State changes occur on the next rising edge of the clock after the internal signal is recognized as valid. The BG signal transitions on the falling edge of the clock after a state is reached during which G changes. The bus control signals (controlled by T) are driven by the processor immediately following a state change when bus mastership is returned to the MC68EC020. State 0, at the top center of the diagram, in which both G and T are negated, is the state of the bus arbiter while the processor is bus master. Request R keeps the arbiter in state 0 as long as it is negated. When a request R is received, both grant G and signal T are asserted (in state 1 at the top left). The next clock causes a change to state 2, at the lower left, in which G and T are held. The bus arbiter remains in that state until request R is negated. Then the arbiter changes to the center state, state 3, and negates grant G. The next clock takes the arbiter to state 4, at the upper right, in which grant G remains negated and signal T remains asserted. The arbiter returns to the original state, state 0, and negates signal T. This sequence of states follows the normal sequence of signals for relinquishing the bus to an external bus master. Other states apply to other possible sequences of R. The MC68EC020 does not allow arbitration of the external bus during the read-modifywrite sequence. For the duration of this sequence, the MC68EC020 ignores the BR input. If mastership of the MC68EC020 bus is required during a read-modify-write operation, BERR must be used to abort the read-modify-write sequence. The bus arbitration sequence while the bus is inactive (i.e., executing internal operations such as a multiply instruction) is shown in Figure 5-49. 5-74 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S4 S0 CLK A23-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... AS DS DSACK1 DSACK0 D31-D0 BR BG PROCESSOR BUS INACTIVE (ARBITRATION PERMITTED WHILE THE PROCESSOR IS INACTIVE OR HALTED) ALTERNATE MASTER PROCESSOR Figure 5-49. MC68EC020 Bus Arbitration Operation Timing--Bus Inactive The existing three-wire arbitration design (BR, BG, and BGACK) of some peripherals can be converted to the MC68EC020 two-wire arbitration with the addition of an AND gate. Figure 5-50 shows the combination of BR and BGACK for a three-wire arbitration system to BR of the MC68EC020 or BR and BG from an MC68EC020 to BG for a three-wire arbitration system. The speed of the AND gate must be faster than the time between the assertion of BGACK and the negation of BR by the alternate bus master. Figure 5-50 assumes the alternate bus master does not assume bus mastership until the MC68EC020 AS is negated and MC68EC020 BG is asserted. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-75 Freescale Semiconductor, Inc. An example of MC68EC020 bus arbitration to a DMA device that supports three-wire bus arbitration is described in Appendix A Interfacing an MC68EC020 to a DMA Device That Supports a Three-Wire Bus Arbitration Protocol. ALTERNATE BUS MASTER MC68EC020 AS AS BG BG BR BR Freescale Semiconductor, Inc... BGACK Figure 5-50. Interface for Three-Wire to Two-Wire Bus Arbitration 5.8 RESET OPERATION RESET is a bidirectional signal with which an external device resets the system or the processor resets external devices. When power is applied to the system, external circuitry should assert RESET for a minimum of 520 clocks after V CC and clock timing have stabilized and are within specification limits. Figure 5-51 is a timing diagram of the powerup reset operation, showing the relationships between RESET, V CC, and bus signals. The clock signal is required to be stable by the time VCC reaches the minimum operating specification. During the reset period, the entire bus three-states (except for non-threestatable signals, which are driven to their inactive state). Once RESET negates, all control signals are negated, the data bus is in read mode, and the address bus is driven. After this, the first bus cycle for reset exception processing begins. The external RESET signal resets the processor and the entire system. Except for the initial reset, RESET should be asserted for at least 520 clock periods to ensure that the processor resets. Asserting RESET for 10 clock periods is sufficient for resetting the processor logic; the additional clock periods prevent a RESET instruction from overlapping the external RESET signal. 5-76 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. CLK +5 V t 520 CLOCKS VCC t < 4 CLOCKS RESET 4 CLOCKS BUS CYCLES ENTIRE BUS THREESTATED BUS STATE UNKNOWN ALL CONTROL SIGNALS NEGATED, DATA BUS IN READ MODE, ADDRESS BUS DRIVEN ISP READ STARTS Freescale Semiconductor, Inc... Figure 5-51. Initial Reset Operation Timing Resetting the processor causes any bus cycle in progress to terminate as if DSACK1/DSACK0 or BERR had been asserted. In addition, the processor initializes registers appropriately for a reset exception. Exception processing for a reset operation is described in Section 6 Exception Processing. When a RESET instruction is executed, the processor drives the RESET signal for 512 clock cycles. In this case, the processor resets the external devices of the system, and the internal registers of the processor are unaffected. The external devices connected to the RESET signal are reset at the completion of the RESET instruction. An external RESET signal that is asserted to the processor during execution of a RESET instruction must extend beyond the reset period of the instruction by at least eight clock cycles to reset the processor. Figure 5-52 shows the timing information for the RESET instruction. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 5-77 Freescale Semiconductor, Inc. S0 S2 S0 S4 S2 CLK *A31-A0 FC2-FC0 SIZ1-SIZ0 R/W Freescale Semiconductor, Inc... ** ECS ** OCS AS DS DSACK1 DSACK0 ** DBEN D31-D0 HALT RESET RESET INTERNAL 512 CLOCKS READ RESUME NORMAL OPERATION * For the MC68EC020, A23-A0. ** This signal does not apply to the MC68EC020. Figure 5-52. RESET Instruction Timing 5-78 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... SECTION 6 EXCEPTION PROCESSING Exception processing is defined as the activities performed by the processor in preparing to execute a handler routine for any condition that causes an exception. In particular, exception processing does not include execution of the handler routine itself. An introduction to exception processing, as one of the processing states of the MC68020/EC020, is given in Section 2 Processing States. This section describes exception processing in detail, describing the processing for each type of exception. It describes the return from an exception and bus fault recovery. This section also describes the formats of the exception stack frames. For more detail on protocol violation and coprocessor-related exceptions, refer to Section 7 Coprocessor Interface Description. Also, for more detail on exceptions defined for floating-point coprocessors, refer to MC68881UM/AD , MC68881/MC68882 Floating-Point Coprocessor User's Manual. 6.1 EXCEPTION PROCESSING SEQUENCE Exception processing occurs in four functional steps. However, all individual bus cycles associated with exception processing (vector acquisition, stacking, etc.) are not guaranteed to occur in the order in which they are described in this section. Nonetheless, all addresses and offsets from the stack pointer are guaranteed to be as described. The first step of exception processing involves the SR. The processor makes an internal copy of the SR, then sets the S-bit in the SR, changing to the supervisor privilege level. Next, the processor inhibits tracing of the exception handler by clearing the T1 and T0 bits in the SR. For the reset and interrupt exceptions, the processor also updates the interrupt priority mask (bits 10-8 of the SR). In the second step, the processor determines the vector number of the exception. For interrupts, the processor performs an interrupt acknowledge cycle (a read from the CPU address space type 1111; see Figures 5-32 and 5-33) to obtain the vector number. For coprocessor-detected exceptions, the vector number is included in the coprocessor exception primitive response. (Refer to Section 7 Coprocessor Interface Description for a complete discussion of coprocessor exceptions.) For all other exceptions, internal logic provides the vector number. This vector number is used in the last step to calculate the address of the exception vector. Throughout this section, vector numbers are given in decimal notation. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-1 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... For all exceptions other than reset, the third step is to save the current processor context. The processor creates an exception stack frame on the active supervisor stack and fills it with context information appropriate for the type of exception. Other information may also be stacked, depending on which exception is being processed and the state of the processor prior to the exception. If the exception is an interrupt and the M-bit in the SR is set, the processor clears the M-bit and builds a second stack frame on the interrupt stack. The last step initiates execution of the exception handler. The processor multiplies the vector number by four to determine the exception vector offset. The processor then adds the offset to the value stored in the VBR to obtain the memory address of the exception vector. Next, the processor loads the PC (and the ISP for the reset exception) from the exception vector table in memory. After prefetching the first three words to fill the instruction pipe, the processor resumes normal processing at the address in the PC. Table 6-1 contains a description of all the exception vector offsets defined for the MC68020/EC020. As shown in Table 6-1, the first 64 vectors are defined by Motorola, and 192 vectors are reserved for interrupt vectors defined by the user. However, external devices may use vectors reserved for internal purposes at the discretion of the system designer. 6-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 6-1. Exception Vector Assignments Freescale Semiconductor, Inc... Vector Offset Vector Number Hex Space Assignment 0 1 2 3 000 004 008 00C SP SP SD SD Reset Initial Interrupt Stack Pointer Reset Initial Program Counter Bus Error Address Error 4 5 6 7 010 014 018 01C SD SD SD SD Illegal Instruction Zero Divide CHK, CHK2 Instruction cpTRAPcc, TRAPcc, TRAPV Instructions 8 9 10 11 020 024 028 02C SD SD SD SD Privilege Violation Trace Line 1010 Emulator Line 1111 Emulator 12 13 14 15 030 034 038 03C SD SD SD SD (Unassigned, Reserved) Coprocessor Protocol Violation Format Error Uninitialized Interrupt 16-23 040 05C SD SD Unassigned, Reserved 24 25 26 27 060 064 068 06C SD SD SD SD Spurious Interrupt Level 1 Interrupt Autovector Level 2 Interrupt Autovector Level 3 Interrupt Autovector 28 29 30 31 070 074 078 07C SD SD SD SD Level 4 Interrupt Autovector Level 5 Interrupt Autovector Level 6 Interrupt Autovector Level 7 Interrupt Autovector 32-47 080 0BC SD SD TRAP #0-15 Instruction Vectors 48 49 50 51 0C0 0C4 0C8 0CC SD SD SD SD FPCP Branch or Set on Unordered Condition FPCP Inexact Result FPCP Divide by Zero FPCP Underflow 52 53 54 55 0D0 0D4 0D8 0DC SD SD SD SD FPCP Operand Error FPCP Overflow FPCP Signaling NAN Unassigned, Reserved 56 57 58 0E0 0E4 0E8 SD SD SD PMMU Configuration PMMU Illegal Operation PMMU Access Level Violation 59-63 0EC 0FC SD SD Unassigned, Reserved 64-255 100 3FC SD SD User-Defined Vectors (192) SP--Supervisor Program Space SD--Supervisor Data Space MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-3 Freescale Semiconductor, Inc. 6.1.1 Reset Exception Freescale Semiconductor, Inc... Assertion of the RESET signal by external hardware causes a reset exception. For details on the requirements for the assertion of RESET, refer to Section 5 Bus Operation. The reset exception has the highest priority of any exception; it provides for system initialization and recovery from catastrophic failure. When a reset exception is recognized, it aborts any processing in progress and that processing cannot be recovered. Figure 6-1 is a flowchart of the reset exception, which performs the following operations: 1. Clears the T1 and T0 bits in the SR to disable tracing. 2. Places the processor in the interrupt mode of the supervisor privilege level by setting the S-bit and clearing the M-bit in the SR. 3. Sets the I2-I0 bits in the SR to the highest priority level (level 7). 4. Initializes the VBR to zero ($00000000). 5. Clears the E and F bits in the CACR. 6. Invalidates all entries in the instruction cache. 7. Generates a vector number to reference the reset exception vector (two long words) at offset zero in the supervisor program address space. 8. Loads the first long word of the reset exception vector into the interrupt stack pointer. 9. Loads the second long word of the reset exception vector into the PC. After the initial instruction prefetches, program execution begins at the address in the PC. The reset exception does not save the value of either the PC or the SR. As described in Section 5 Bus Operation, if a bus error or address error occurs during the exception processing sequence for a reset, a double bus fault occurs. The processor halts and asserts the HALT signal to indicate the halted condition. Execution of the RESET instruction does not cause a reset exception, nor does it affect any internal registers, but it does cause the MC68020/EC020 to assert the RESET signal, resetting all external devices. 6.1.2 Bus Error Exception A bus error exception occurs when external logic aborts a bus cycle by asserting the BERR signal. If the aborted bus cycle is a data access, the processor immediately begins exception processing. If the aborted bus cycle is an instruction prefetch, the processor may delay taking the exception until it attempts to use the prefetched information. 6-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. ENTRY S (SR) M (SR) T1, T0 (SR) I2-I0 (SR) VBR CACR 1 0 0 $7 $00000000 $00000000 INSTRUCTION CACHE ENTRIES INVALIDATED FETCH VECTOR #0 OTHERWISE SP (VECTOR #0) Freescale Semiconductor, Inc... BUS ERROR FETCH VECTOR #1 (DOUBLE BUS FAULT) EXIT OTHERWISE PC (VECTOR #1) BUS ERROR PREFETCH 3 WORDS (DOUBLE BUS FAULT) EXIT OTHERWISE BEGIN INSTRUCTION EXECUTION BUS ERROR OR ADDRESS ERROR (DOUBLE BUS FAULT) EXIT EXIT Figure 6-1. Reset Operation Flowchart The processor begins exception processing for a bus error by making an internal copy of the current SR. The processor then enters the supervisor privilege level (by setting the Sbit in the SR) and clears the T1 and T0 bits in the SR. The processor generates exception vector number 2 for the bus error vector. It saves the vector offset, PC, and the internal copy of the SR on the active supervisor stack. The saved PC value is the logical address of the instruction that was executing at the time the fault was detected. This is not necessarily the instruction that initiated the bus cycle since the processor overlaps MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-5 Freescale Semiconductor, Inc. execution of instructions. The processor also saves the contents of some of its internal registers. The information saved on the stack is sufficient to identify the cause of the bus fault and recover from the error. Freescale Semiconductor, Inc... For efficiency, the MC68020/EC020 uses two different bus error stack frame formats. When the bus error exception is taken at an instruction boundary, less information is required to recover from the error, and the processor builds the short bus fault stack frame as shown in Table 6-5. When the exception is taken during the execution of an instruction, the processor must save its entire state for recovery and uses the long bus fault stack frame shown in Table 6-5. The format code in the stack frame distinguishes the two stack frame formats. Stack frame formats are described in detail in 6.4 Exception Stack Frame Formats. If a bus error occurs during the exception processing for a bus error, address error, or reset or while the processor is loading internal state information from the stack during the execution of an RTE instruction, a double bus fault occurs and the processor enters the halted state. In this case, the processor does not attempt to alter the current state of memory. Only an external RESET can restart a processor halted by a double bus fault. 6.1.3 Address Error Exception An address error exception occurs when the processor attempts to prefetch an instruction from an odd address. This exception is similar to a bus error exception but is internally initiated. A bus cycle is not executed, and the processor begins exception processing immediately. After exception processing commences, the sequence is the same as that for bus error exceptions described in the preceding paragraphs, except that the vector number is 3 and the vector offset in the stack frame refers to the address error vector. Either a short or long bus fault stack frame may be generated. If an address error occurs during the exception processing for a bus error, address error, or reset, a double bus fault occurs. 6.1.4 Instruction Trap Exception Certain instructions are used to explicitly cause trap exceptions. The TRAP instruction always forces an exception and is useful for implementing system calls in user programs. The TRAPcc, TRAPV, cpTRAPcc, CHK, and CHK2 instructions force exceptions if the user program detects an error, which may be an arithmetic overflow or a subscript value that is out of bounds. The DIVS and DIVU instructions force exceptions if a division operation is attempted with a divisor of zero. When a trap exception occurs, the processor copies the SR internally, enters the supervisor privilege level (by setting the S-bit in the SR), and clears the T1 and T0 bits in the SR. If tracing is enabled for the instruction that caused the trap, a trace exception is taken after the RTE instruction from the trap handler is executed, and the trace corresponds to the trap instruction; the trap handler routine is not traced. The processor generates a vector number according to the instruction being executed; for the TRAP 6-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. instruction, the vector number is 32 plus n. The stack frame saves the trap vector offset, the PC, and the internal copy of the SR on the supervisor stack. The saved value of the PC is the logical address of the instruction following the instruction that caused the trap. For all instruction traps other than TRAP, a pointer to the instruction that caused the trap is also saved. Instruction execution resumes at the address in the exception vector after the required instruction prefetches. Freescale Semiconductor, Inc... 6.1.5 Illegal Instruction and Unimplemented Instruction Exceptions An illegal instruction is an instruction that contains any bit pattern in its first word that does not correspond to the bit pattern of the first word of a valid MC68020/EC020 instruction or a MOVEC instruction with an undefined register specification field in the first extension word. An illegal instruction exception corresponds to vector number 4 and occurs when the processor attempts to execute an illegal instruction. An illegal instruction exception is also taken if a breakpoint acknowledge bus cycle (see Section 5 Bus Operation) is terminated with the assertion of the BERR signal. This implies that the external circuitry did not supply an instruction word to replace the BKPT instruction word in the instruction pipe. Instruction word patterns with bits 15-12 = 1010 are referred to as unimplemented instructions with A-line opcodes. When the processor attempts to execute an unimplemented instruction with an A-line opcode, an exception is generated with vector number 10, permitting efficient emulation of unimplemented instructions. Instructions that have word patterns with bits 15-12 = 1111, bits 11-9 = 000, and defined word patterns for subsequent words, are legal PMMU instructions. Instructions that have bits 15-12 of the first words = 1111, bits 11-9 = 000, and undefined patterns in the subsequent words, are treated as unimplemented instructions with F-line opcodes when execution is attempted in the supervisor privilege level. When execution of the same instruction is attempted in the user privilege level, a privilege violation exception is taken. The exception vector number for an unimplemented instruction with an F-line opcode is 11. The word patterns with bits 15-12 = 1111 and bits 11-9 000 are used for coprocessor instructions. When the processor identifies a coprocessor instruction, it runs a bus cycle referencing CPU space type $2 (refer to Section 2 Processing States) and addressing one of eight coprocessors (0-7, according to bits 11-9). If the addressed coprocessor is not included in the system and the cycle terminates with the assertion of BERR , the instruction takes an unimplemented instruction (F-line opcode) exception. The system can emulate the functions of the coprocessor with an F-line exception handler. Refer to Section 7 Coprocessor Interface Description for more details. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-7 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Exception processing for illegal and unimplemented instructions is similar to that for instruction traps. When the processor has identified an illegal or unimplemented instruction, it initiates exception processing instead of attempting to execute the instruction. The processor copies the SR, enters the supervisor privilege level (by setting the S bit in the SR), and clears the T1 and T0 bits in the SR, disabling further tracing. The processor generates the vector number, either 4, 10, or 11, according to the exception type. The illegal or unimplemented instruction vector offset, current PC, and copy of the SR are saved on the supervisor stack, with the saved value of the PC being the address of the illegal or unimplemented instruction. Instruction execution resumes at the address contained in the exception vector. It is the responsibility of the handling routine to adjust the stacked PC if the instruction is emulated in software or is to be skipped on return from the handler. 6.1.6 Privilege Violation Exception To provide system security, the following instructions are privileged: ANDI to SR EORI to SR cpRESTORE cpSAVE MOVE from SR MOVE to SR MOVE USP MOVEC MOVES ORI to SR RESET RTE STOP An attempt to execute one of the privileged instructions while at the user privilege level causes a privilege violation exception. Also, a privilege violation exception occurs if a coprocessor requests a privilege check and the processor is at the user level. Exception processing for privilege violations is similar to that for illegal instructions. When the processor identifies a privilege violation, it begins exception processing before executing the instruction. The processor copies the SR, enters the supervisor privilege level by setting the S-bit in the SR, and clears the T1 and T0 bits in the SR. The processor generates vector number 8, the privilege violation exception vector, and saves the privilege violation vector offset, the current PC value, and the internal copy of the SR on the supervisor stack. The saved value of the PC is the logical address of the first word of the instruction that caused the privilege violation. Instruction execution resumes after the required prefetches from the address in the privilege violation exception vector. 6-8 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 6.1.7 Trace Exception Freescale Semiconductor, Inc... To aid in program development, the M68000 processors include an instruction-byinstruction tracing capability. The MC68020/EC020 can be programmed to trace all instructions or only instructions that change program flow. In the trace mode, an instruction generates a trace exception after it completes execution, allowing a debugger program to monitor execution of a program. The T1 and T0 bits in the supervisor portion of the SR control tracing. The state of these bits when an instruction begins execution determines whether the instruction generates a trace exception after the instruction completes. Clearing both the T1 and T0 bits disables tracing, and instruction execution proceeds normally. Clearing the T1 bit and setting the T0 bit causes an instruction that forces a change of flow to take a trace exception. Instructions that increment the PC normally do not take the trace exception. Instructions that are traced in this mode include all branches, jumps, instruction traps, returns, and coprocessor instructions that modify the PC flow. This mode also includes SR manipulations because the processor must re-prefetch instruction words to fill the pipe again any time an instruction that can modify the SR is executed. The execution of the BKPT instruction causes a change of flow if the opcode replacing the BKPT is an instruction that causes a change of flow (i.e., a jump, branch, etc.). Setting the T1 bit and clearing the T0 bit causes the execution of all instructions to force trace exceptions. Table 6-2 shows the trace mode selected by each combination of T1 and T0. Table 6-2. Tracing Control TI T0 Tracing Function 0 0 No Tracing 0 1 Trace on Change of Flow (BRA, JMP, etc.) 1 0 Trace on Instruction Execution (Any Instruction) 1 1 Undefined, Reserved In general terms, a trace exception is an extension to the function of any traced instruction--i.e., the execution of a traced instruction is not complete until completion of trace exception processing. If an instruction does not complete due to a bus error or address error exception, trace exception processing is deferred until after the execution of the suspended instruction is resumed, and the instruction execution completes normally. If an interrupt is pending at the completion of an instruction, the trace exception processing occurs before the interrupt exception processing starts. If an instruction forces an exception as part of its normal execution, the forced exception processing occurs before the trace exception is processed. See 6.1.11 Multiple Exceptions for a more complete discussion of exception priorities. When tracing is enabled and the processor attempts to execute an illegal or unimplemented instruction, that instruction does not cause a trace exception since it is not executed. This is of particular importance to an instruction emulation routine that performs the instruction function, adjusts the stacked PC to skip the unimplemented instruction, and returns. Before returning, the T1 and T0 bits of the SR on the stack should be checked. If MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-9 Freescale Semiconductor, Inc. tracing is enabled, the trace exception processing should also be emulated for the trace exception handler to account for the emulated instruction. Freescale Semiconductor, Inc... The exception processing for a trace starts at the end of normal processing for the traced instruction and before the start of the next instruction. The processor makes an internal copy of the SR and enters the supervisor privilege level (by setting the S-bit in the SR). It also clears the T0 and T1 bits of the SR, disabling further tracing. The processor supplies vector number 9 for the trace exception and saves the trace exception vector offset, PC value, and the copy of the SR on the supervisor stack. The saved value of the PC is the logical address of the next instruction to be executed. Instruction execution resumes after the required prefetches from the address in the trace exception vector. The STOP instruction does not perform its function when it is traced. A STOP instruction that begins execution with T1, T0 = 10 forces a trace exception after it loads the SR. Upon return from the trace handler routine, execution continues with the instruction following the STOP instruction, and the processor never enters the stopped condition. 6.1.8 Format Error Exception Just as the processor checks that prefetched instructions are valid, the processor (with the aid of a coprocessor, if needed) also performs some checks of data values for control operations, including the type and option fields of the descriptor for CALLM, the coprocessor state frame format word for a cpRESTORE instruction, and the stack frame format for an RTE or an RTM instruction. The RTE instruction checks the validity of the stack format code. For long bus fault format frames, the RTE instruction also compares the internal version number of the processor to that contained in the frame at memory location SP + 54 (SP + $36). This check ensures that the processor can correctly interpret internal state information from the stack frame. The CALLM and RTM both check the values in the option and type fields in the module descriptor and module stack frame, respectively. If these fields do not contain proper values or if an illegal access rights change request is detected by an external memory management unit, then an illegal call or return is being requested and is not executed. Refer to Section 9 Applications Information for more information on the module call/return mechanism. The cpRESTORE instruction passes the format word of the coprocessor state frame to the coprocessor for validation. If the coprocessor does not recognize the format value, it signals the MC68020/EC020 to take a format error exception. Refer to Section 7 Coprocessor Interface Description for details of coprocessor-related exceptions. If any of the checks previously described determine that the format of the stacked data is improper, the instruction generates a format error exception. This exception saves a short bus fault stack frame, generates exception vector number 14, and continues execution at the address in the format exception vector. The stacked PC value is the logical address of the instruction that detected the format error. 6-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 6.1.9 Interrupt Exceptions When a peripheral device requires the services of the MC68020/EC020 or is ready to send information that the processor requires, it may signal the processor to take an interrupt exception. The interrupt exception transfers control to a routine that responds appropriately. Freescale Semiconductor, Inc... The peripheral device uses the IPL2-IPL0 signals to signal an interrupt condition to the processor and to specify the priority of that condition. These three signals encode a value of zero through seven (IPL0 is the least significant bit). When IPL2- IPL0 are all negated, the interrupt request level is zero. IPL2-IPL0 values 1-7 specify one of seven levels of prioritized interrupts; level 7 has the highest priority. External circuitry can chain or otherwise merge signals from devices at each level, allowing an unlimited number of devices to interrupt the processor. The IPL2- I P L 0 signals must maintain the interrupt request level until the MC68020/EC020 acknowledges the interrupt to guarantee that the interrupt is recognized. The MC68020/EC020 continuously samples the IPL2- IPL0 signals on consecutive falling edges of the processor clock to synchronize and debounce these signals. An interrupt request that is the same for two consecutive falling clock edges is considered a valid input. Although the protocol requires that the request remain until the processor runs an interrupt acknowledge cycle for that interrupt value, an interrupt request that is held for as short a period as two clock cycles could be recognized. The I2-I0 bits in the SR specify the interrupt priority mask. The value in the interrupt mask is the highest priority level that the processor ignores. When an interrupt request has a priority higher than the value in the mask, the processor makes the request a pending interrupt. Figure 6-2 is a flowchart of the procedure for making an interrupt pending. When several devices are connected to the same interrupt level, each device should hold its interrupt priority level constant until its corresponding interrupt acknowledge cycle to ensure that all requests are processed. Table 6-3 lists the interrupt levels, the states of IPL2- IPL0 that define each level, and the mask value that allows an interrupt at each level. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-11 Freescale Semiconductor, Inc. RESET SAMPLE AND SYNCH IPL2-IPL0 (COMPARE INTERRUPT LEVEL WITH STATUS REGISTER MASK) INTERRUPT LEVEL > I2-I0, OR TRANSITION ON LEVEL 7 OTHERWISE Freescale Semiconductor, Inc... INTERRUPT PENDING (MC68020 ASSERTS IPEND *) * IPEND is not implemented in the MC68EC020. Figure 6-2. Interrupt Pending Procedure Table 6-3. Interrupt Levels and Mask Values Control Line Status Requested Interrupt Level IPL2 IPL1 IPL0 Interrupt Mask Value Required for Recognition 0* N N N N/A* 1 N N A 0 2 N A N 1-0 3 N A A 2-0 4 A N N 3-0 5 A N A 4-0 6 A A N 5-0 7 A A A 7-0 *Indicates that no interrupt is requested. A--Asserted N--Negated Priority level 7, the nonmaskable interrupt, is a special case. Level 7 interrupts cannot be masked by the interrupt priority mask, and they are transition sensitive. The processor recognizes an interrupt request each time the external interrupt request level changes from some lower level to level 7, regardless of the value in the mask. Figure 6-3 shows two examples of interrupt recognitions, one for level 6 and one for level 7. When the MC68020/EC020 processes a level 6 interrupt, the interrupt priority mask is automatically updated with a value of 6 before entering the handler routine so that subsequent level 6 interrupts are masked. Provided no instruction that lowers the mask value is executed, the 6-12 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... external request can be lowered to level 3 and then raised back to level 6, and a second MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-13 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... level 6 interrupt is not processed. However, if the MC68020/EC020 is handling a level 7 interrupt (I2-I0 in the SR set to 111) and the external request is lowered to level 3 and then raised back to level 7, a second level 7 interrupt is processed. The second level 7 interrupt is processed because the level 7 interrupt is transition sensitive. A level 7 interrupt is also generated by a level comparison if the request level and mask level are at 7 and the priority mask is then set to a lower level (with the MOVE to SR or RTE instruction, for example). As shown in Figure 6-3 for level 6 interrupt request level and mask level, this is the case for all interrupt levels. Note that a mask value of 6 and a mask value of 7 both inhibit request levels of 1-6 from being recognized. In addition, neither masks a transition to an interrupt request level of 7. The only difference between mask values of 6 and 7 occurs when the interrupt request level is 7 and the mask value is 7. If the mask value is lowered to 6, a second level 7 interrupt is recognized. EXTERNAL IPL2-IPL0 INTERRUPT PRIORITY MASK (I2-I0 IN SR) ACTION LEVEL 6 EXAMPLE 100 ($3) 101 ($5) INITIAL CONDITIONS IF 001 ($6) THEN 110 ($6) AND LEVEL 6 INTERRUPT (LEVEL COMPARISON) IF 100 ($3) AND STILL 110 ($6) THEN NO ACTION IF 001 ($6) AND STILL 110 ($6) THEN NO ACTION IF STILL 001 ($6) AND RTE SO THAT 101 ($5) THEN LEVEL 6 INTERRUPT (LEVEL COMPARISON) LEVEL 7 EXAMPLE 100 ($3) 101 ($5) INITIAL CONDITIONS IF 000 ($7) THEN 111 ($7) AND LEVEL 7 INTERRUPT (TRANSITION) IF 100 ($3) AND STILL 111 ($7) THEN NO ACTION IF 000 ($7) AND STILL 111 ($7) THEN NO ACTION IF STILL 000 ($7) AND RTE SO THAT 101 ($5) THEN LEVEL 7 INTERRUPT (LEVEL COMPARISON) (TRANSITION) Figure 6-3. Interrupt Recognition Examples 6-14 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The MC68020 asserts IPEND (note that IPEND is not implemented in the MC68EC020) when it makes an interrupt request pending. Figure 6-4 shows the assertion of IPEND relative to the assertion of an interrupt level on IPL2- IPL0. IPEND signals to external devices that an interrupt exception will be taken at an upcoming instruction boundary (following any higher priority exception). The state of the IPEND signal is internally checked by the processor once per instruction, independently of bus operation. In addition, it is checked during the second instruction prefetch associated with exception processing. Figure 6-5 is a flowchart of the interrupt recognition and associated exception processing sequence. Freescale Semiconductor, Inc... CLK IPL2-IPL0 IPEND IPL2-IPL0 RECOGNIZED ASSERT IPEND IPL2-IPL0 SYNCHRONIZED COMPARE REQUEST WITH MASK IN SR Figure 6-4. Assertion of IPEND (MC68020 Only) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-15 Freescale Semiconductor, Inc. ONCE PER INSTRUCTION AT INSTRUCTION BOUNDARY OTHERWISE *IPEND ASSERTED EXIT Freescale Semiconductor, Inc... * NEGATE IPEND EXECUTE INTERRUPT ACKNOWLEDGE CYCLE TEMP SR 1 S 0 T1, T0 UPDATE I2-I0 - (SP) TEMP - (SP) PC - (SP) FORMAT WORD - (SP) OTHER EXCEPTION DEPENDENT INFORMATION M=1 M=0 VECTOR TABLE ENTRY THESE INDIVIDUAL BUS CYCLES MAY OCCUR IN ANY ORDER PC TEMP M SR 0 PREFETCH 3 WORDS END OF EXCEPTION PROCESSING FOR THE INTERRUPT BEGIN EXECUTION OF THE INTERRUPT HANDLER ROUTINE OR PROCESS A HIGHER PRIORITY EXCEPTION * Does not apply to the MC68EC020. Figure 6-5. Interrupt Exception Processing Flowchart 6-16 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... For the MC68020, if no higher priority interrupt has been synchronized, the IPEND signal is negated during state 0 (S0) of an interrupt acknowledge cycle, and the IPL2-IPL0 signals for the interrupt being acknowledged can be negated at this time. For the MC68EC020, if no higher priority interrupt has been synchronized, the IPL2-IPL0 signals for the interrupt being acknowledged can be negated at this time. Refer to Section 5 Bus Operation for more information on interrupt acknowledge cycles. When processing an interrupt exception, the MC68020/EC020 first makes an internal copy of the SR, sets the privilege level to supervisor, suppresses tracing, and sets the processor interrupt mask level to the level of the interrupt being serviced. The processor attempts to obtain a vector number from the interrupting device using an interrupt acknowledge bus cycle with the interrupt level number output on pins A3-A1 of the address bus. For a device that cannot supply an interrupt vector, the AVEC signal can be asserted, and the MC68020/EC020 uses an internally generated autovector, which is one of vector numbers 31-25, that corresponds to the interrupt level number. If external logic indicates a bus error during the interrupt acknowledge cycle, the interrupt is considered spurious, and the processor generates the spurious interrupt vector number (24). Refer to Section 5 Bus Operation for complete interrupt bus cycle information. Once the vector number is obtained, the processor saves the exception vector offset, PC value, and the internal copy of the SR on the active supervisor stack. The saved value of the PC is the logical address of the instruction that would have been executed had the interrupt not occurred. If the interrupt was acknowledged during the execution of a coprocessor instruction, further internal information is saved on the stack so that the MC68020/EC020 can continue executing the coprocessor instruction when the interrupt handler completes execution. If the M-bit in the SR is set, the processor clears the M-bit and creates a throwaway exception stack frame on top of the interrupt stack as part of interrupt exception processing. This second frame contains the same PC value and vector offset as the frame created on top of the master stack, but has a format number of 1 instead of 0 or 9. The copy of the SR saved on the throwaway frame is exactly the same as that placed on the master stack except that the S-bit is set in the version placed on the interrupt stack. (It may or may not be set in the copy saved on the master stack.) The resulting SR (after exception processing) has the S-bit set and the M-bit cleared. The processor loads the address in the exception vector into the PC, and normal instruction execution resumes after the required prefetches for the interrupt handler routine. Most M68000 family peripherals use programmable interrupt vector numbers as part of the interrupt request/acknowledge mechanism of the system. If this vector number is not initialized after reset and the peripheral must acknowledge an interrupt request, the peripheral usually returns the uninitialized interrupt vector number (15). MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-17 Freescale Semiconductor, Inc. 6.1.10 Breakpoint Instruction Exception Freescale Semiconductor, Inc... To use the MC68020/EC020 in a hardware emulator, it must provide a means of inserting breakpoints in the emulator code and of performing appropriate operations at each breakpoint. For the MC68000 and MC68008, this can be done by inserting an illegal instruction at the breakpoint and detecting the illegal instruction exception from its vector location. However, since the VBR on M68000 family processors MC68010 and later allows arbitrary relocation of exception vectors, the exception address cannot reliably identify a breakpoint. The MC68020/EC020 processor provides a breakpoint capability with a set of breakpoint instructions, $4848-$484F, for eight unique breakpoints. The breakpoint facility also allows external hardware to monitor the execution of a program residing in the on-chip instruction cache without severe performance degradation. When the MC68020/EC020 executes a breakpoint instruction, it performs a breakpoint acknowledge cycle (read cycle) from CPU space type $0 with address lines A4-A2 corresponding to the breakpoint number. Refer to Section 5 Bus Operation for a description of the breakpoint acknowledge cycle. The external hardware can return either BERR or DSACK1/DSACK0 with an instruction word on the data bus. If the bus cycle terminates with BERR, the processor performs illegal instruction exception processing. If the bus cycle terminates with DSACK1/DSACK0, the processor uses the data returned to replace the breakpoint instruction in the internal instruction pipe and begins execution of that instruction. The remainder of the pipe remains unaltered. In addition, no stacking or vector fetching is involved with the execution of the instruction. Figure 6-6 is a flowchart of the breakpoint instruction execution. 6.1.11 Multiple Exceptions When several exceptions occur simultaneously, they are processed according to a fixed priority. Table 6-4 lists the exceptions grouped by characteristics. Each group has a priority from 4-0. Priority 0 has the highest priority. As soon as the MC68020/EC020 has completed exception processing for a condition when another exception is pending, it begins exception processing for the pending exception instead of executing the exception handler for the original exception condition. Also, whenever a bus error or address error occurs, its exception processing takes precedence over lower priority exceptions and occurs immediately. For example, if a bus error occurs during the exception processing for a trace condition, the system processes the bus error and executes its handler before completing the trace exception processing. However, most exceptions cannot occur during exception processing, and very few combinations of the exceptions shown in Table 6-4 can be pending simultaneously. 6-18 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. ENTRY A4-A2 A19-A16 $0 BREAKPOINT NUMBER CYCLE TERMINATED WITH DSACK1/DSACK0 CYCLE TERMINATED WITH BERR Freescale Semiconductor, Inc... INITIATE READ BUS CYCLE TAKE ILLEGAL INSTRUCTION EXCEPTION PIPE STAGE D INSTRUCTION WORD ON DATA BUS EXECUTE INSTRUCTION WORD EXIT Figure 6-6. Breakpoint Instruction Flowchart Table 6-4. Exception Priority Groups Group/ Priority Exception and Relative Priority Characteristic 0 0.0--Reset Aborts all processing (instruction or exception) and does not save old context. 1 1.0--Address Error 1.1--Bus Error Suspends processing (instruction or exception) and saves internal context. 2 2.0--BKPT, CALLM, CHK, CHK2, cp Midinstruction, cp Protocol Violation, cpTRAPcc, Divide by Zero, RTE, RTM, TRAP, TRAPcc, TRAPV Exception processing is part of instruction execution. 3 3.0--Illegal Instruction, Line A, Unimplemented Line F, Privilege Violation, cp Preinstruction Exception processing begins before instruction is executed. 4 4.0--cp Postinstruction 4.1--Trace 4.2--Interrupt Exception processing begins when current instruction or previous exception processing has completed. NOTE: 0.0 is the highest priority; 4.2 is the lowest. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-19 Freescale Semiconductor, Inc. The priority scheme is very important in determining the order in which exception handlers execute when several exceptions occur at the same time. As a general rule, the lower the priority of an exception, the sooner the handler routine for that exception executes. For example, if simultaneous trap, trace, and interrupt exceptions are pending, the exception processing for the trap occurs first, followed immediately by exception processing for the trace, and then for the interrupt. When the processor resumes normal instruction execution, it is in the interrupt handler, which returns to the trace handler, which returns to the trap exception handler. This rule does not apply to the reset exception; its handler is executed first even though it has the highest priority because the reset operation clears all other exceptions. Freescale Semiconductor, Inc... 6.1.12 Return from Exception After the MC68020/EC020 has completed exception processing for all pending exceptions, it resumes normal instruction execution at the address in the vector for the last exception processed. Once the exception handler has completed execution, the processor must return to the system context prior to the exception (if possible). The RTE instruction returns from the handler to the previous system context for any exception. When the processor executes an RTE instruction, it examines the stack frame on top of the active supervisor stack to determine if it is a valid frame and what type of context restoration it requires. The following paragraphs describe the processing for each of the stack frame types; refer to 6.3 Coprocessor Considerations for a description of the stack frame type formats. For a normal four-word frame, the processor updates the SR and PC with the data read from the stack, increments the stack pointer by eight, and resumes normal instruction execution. For the throwaway four-word frame, the processor reads the SR value from the frame, increments the active stack pointer by eight, updates the SR with the value read from the stack, and then begins RTE processing again, as shown in Figure 6-7. The processor reads a new format word from the stack frame on top of the active stack (which may or may not be the same stack used for the previous operation) and performs the proper operations corresponding to that format. In most cases, the throwaway frame is on the interrupt stack and when the SR value is read from the stack, the S and M bits are set. In that case, there is a normal four-word frame or a ten-word coprocessor midinstruction frame on the master stack. However, the second frame may be any format (even another throwaway frame) and may reside on any of the three system stacks. For the six-word stack frame, the processor restores the SR and PC values from the stack, increments the active supervisor stack pointer by 12, and resumes normal instruction execution. 6-20 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. ENTRY TEMP (SP) + READ FORMAT WORD SR TEMP SP SP + 6 INVALID FORMAT WORD OTHERWISE TAKE FORMAT ERROR EXCEPTION OTHERWISE FORMAT CODE = $0 (FOUR-WORD FRAME) OTHERWISE OTHER FORMATS Freescale Semiconductor, Inc... FORMAT CODE = $1 (THROWAWAY FRAME) PC (SP) + SP SP + 6 SR TEMP EXIT Figure 6-7. RTE Instruction for Throwaway Four-Word Frame For the coprocessor midinstruction stack frame, the processor reads the SR, PC, instruction address, internal register values, and the evaluated effective address from the stack, restores these values to the corresponding internal registers, and increments the stack pointer by 20. The processor then reads from the response register of the coprocessor that initiated the exception to determine the next operation to be performed. Refer to Section 7 Coprocessor Interface Description for details of coprocessor-related exceptions. For both the short and long bus fault stack frames, the processor first checks the format value on the stack for validity. In addition, for the long stack frame, the processor compares the version number in the stack with its own version number. The version number is located in the most significant nibble (bits 15-12) of the word at location SP + $36 in the long stack frame. This validity check is required in a multiprocessor system to ensure that the data is properly interpreted by the RTE instruction. The RTE instruction also reads from both ends of the stack frame to make sure it is accessible. If the frame is invalid or inaccessible, the processor takes a format error or a bus error exception, respectively. Otherwise, the processor reads the entire frame into the proper internal registers, deallocates the stack, and resumes normal processing. Once the processor begins to load the frame to restore its internal state, the assertion of the BERR signal MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-21 Freescale Semiconductor, Inc. causes the processor to enter the halted state. Refer to 6.2 Bus Fault Recovery for a description of the processing that occurs after the frame is read into the internal registers. If a format error or bus error exception occurs during the frame validation sequence of the RTE instruction, either due to any of the errors previously described or due to an illegal format code, the processor creates a normal four-word or a bus fault stack frame below the frame that it was attempting to use. In this way, the faulty stack frame remains intact. The exception handler can examine or repair the faulty frame. In a multiprocessor system, the faulty frame can be left to be used by another processor of a different type (e.g., an MC68010 or a future M68000 family processor) when appropriate. Freescale Semiconductor, Inc... 6.2 BUS FAULT RECOVERY An address error exception or a bus error exception indicates a bus fault. The saving of the processor state for a bus error or address error is described in 6.1.2 Bus Error Exception, and the restoring of the processor state by an RTE instruction is described in 6.1.12 Return from Exception. Processor accesses of either data items or the instruction stream can result in bus errors. When a bus error exception occurs while accessing a data item, the exception is taken immediately after the bus cycle terminates. The processor may never access an instruction that is part of the instruction stream. In this case, the bus error would not be processed. For instruction faults, when the short bus fault stack frame applies, the address of the pipe stage B word is the value in the PC plus four, and the address of the stage C word is the value in the PC plus two. For the long format, the long word at SP + $24 contains the address of the stage B word; the address of the stage C word is the address of the stage B word minus two. Address error faults occur only for instruction stream accesses, and the exceptions are taken before the bus cycles are attempted. 6.2.1 Special Status Word (SSW) The internal SSW (see Figure 6-8) is one of several registers saved as part of the bus fault exception stack frame. Both the short bus fault format and the long bus fault format include this word at offset $A. The bus cycle fault stack frame formats are described in detail in 6.4 Exception Stack Frame Formats. The SSW information indicates whether the fault was caused by an access to the instruction stream, data stream, or both. The high-order half of the SSW contains two status bits each for the B and C stages of the instruction pipe. If an address error exception occurs, the fault bits written to the stack frame are not set (they are only set due to a bus error, as previously described), and the rerun bits alone show the cause of the exception. Depending on the state of the pipeline, either RB and RC are set, or only RC is set. To correct the pipeline contents and continue execution of the suspended instruction, software must place the correct instruction stream data in the stage C and/or stage B images requested by the rerun bits and must clear the rerun bits. The least significant half of the SSW applies to data cycles only. Data and instruction stream faults may be pending simultaneously; the fault handler should be able to recognize any combination of the FC, FB, RC, RB, and DF bits. 6-22 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 15 14 13 12 11 10 9 8 7 6 FC FB RC RB 0 0 0 DF RM RW 5 4 SIZE 3 0 2 0 FC2-FC0 Figure 6-8. Special Status Word Format Freescale Semiconductor, Inc... FC--Fault on Stage C When the FC bit is set, the processor attempted to use stage C and found it to be marked invalid due to a bus error on the prefetch for that stage. FC can be used by a bus error handler to determine the cause(s) of a bus error exception. FB--Fault on Stage B When the FB bit is set, the processor attempted to use stage B and found it to be marked invalid due to a bus error on the prefetch for that stage. FB can be used by a bus error handler to determine the cause(s) of a bus error exception. RC--Rerun Flag for Stage C The RC bit is set to indicate that a fault occurred during a prefetch for stage C. The RC bit is always set when the FC bit is set. The RC bit indicates that the word in stage C of the instruction pipe is invalid, and the state of the bit can be used by a handler to repair the values in the pipe after an address error or a bus error, if necessary. If the RC bit is set when the processor executes an RTE instruction, the processor may execute a bus cycle to prefetch the instruction word for stage C of the pipe (if it is required). If the RC and FC bits are set, the RTE instruction automatically reruns the prefetch cycle for stage C. The address space for the bus cycle is the program space for the privilege level indicated in the copy of the SR on the stack. If the RC bit is clear, the words on the stack for stage C of the pipe are accepted as valid; the processor assumes that there is no prefetch pending for stage C and that software has repaired or filled the image of stage C, if necessary. 1 = Rerun faulted bus cycle or run pending prefetch 0 = Do not rerun bus cycle RB--Rerun Flag for Stage B The RB bit is set to indicate that a fault occurred during a prefetch for stage B. The RB bit is always set when the FB bit is set. The RB bit indicates that the word in stage B of the instruction pipe is invalid, and the state of the bit can be used by a handler to repair the values in the pipe after an address error or a bus error, if necessary. If the RB bit is set when the processor executes an RTE instruction, the processor may execute a bus cycle to prefetch the instruction word for stage B of the pipe (if it is required). If the RB and FB bits are set, the RTE instruction automatically reruns the prefetch cycle for stage B. The address space for the bus cycle is the program space for the privilege level indicated in the copy of the SR on the stack. If the RB bit is clear, the words on the MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-23 Freescale Semiconductor, Inc. stack for stage B of the pipe are accepted as valid; the processor assumes that there is no prefetch pending for stage B and that software has repaired or filled the image of stage B, if necessary. 1 = Rerun faulted bus cycle or run pending prefetch 0 = Do not rerun bus cycle Freescale Semiconductor, Inc... Bits 11-9--Reserved by Motorola DF--Fault/Rerun Flag If the DF bit is set, a data fault has occurred and caused the exception. If the DF bit is set when the processor reads the stack frame, it reruns the faulted data access; otherwise, it assumes that the data input buffer value on the stack is valid for a read or that the data has been correctly written to memory for a write (or that no data fault occurred). 1 = Rerun faulted bus cycle or run pending prefetch 0 = Do not rerun bus cycle RM--Read-Modify-Write 1 = Read-modify-write operation on data cycle 0 = Not a read-modify-write operation RW--Read/Write 1 = Read on data cycle 0 = Write on data cycle SIZE--Size Code The SIZE field indicates the size of the operand access for the data cycle. Bit 3--Reserved by Motorola FC2-FC0--Specifies the address space for data cycle 6.2.2 Using Software to Complete the Bus Cycles One method of completing a faulted bus cycle is to use a software handler to emulate the cycle. This is the only method for correcting address errors. The handler should emulate the faulted bus cycle in a manner that is transparent to the instruction that caused the fault. For instruction stream faults, the handler may need to run bus cycles for both the B and C stages of the instruction pipe. The RB and RC bits of the SSW identify the stages that may require a bus cycle; the FB and FC bits of the SSW indicate that a stage was invalid when an attempt was made to use its contents. Those stages must be repaired. For each faulted stage, the software handler should copy the instruction word from the proper address space as indicated by the S-bit of the copy of the SR saved on the stack to the image of the appropriate stage in the stack frame. In addition, the handler must clear the RB or RC bit associated with the stage that it has corrected. The handler should not change the FB and FC bits. 6-24 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... To repair data faults (indicated by DF = 1), the software should first examine the RM bit in the SSW to determine if the fault was generated during a read-modify-write operation. If RM = 0, the handler should then check the RW bit of the SSW to determine if the fault was caused by a read or a write cycle. For data write faults, the handler must transfer the properly sized data from the data output buffer on the stack frame to the location indicated by the data fault address in the address space defined by the SSW. (Both the data output buffer and the data fault address are part of the stack frame at SP + $18 and SP + $10, respectively.) Data read faults only generate the long bus fault frame, and the handler must transfer properly sized data from the location indicated by the fault address and address space to the image of the data input buffer at location SP + $2C of the long format stack frame. Byte, word, and 3-byte operands are right justified in the 4-byte data buffers. In addition, the software handler must clear the DF bit of the SSW to indicate that the faulted bus cycle has been corrected. To emulate a read-modify-write cycle, the exception handler must first read the operation word at the PC address (SP + 2 of the stack frame). This word identifies the CAS, CAS2, or TAS instruction that caused the fault. Then the handler must emulate this entire instruction (which may consist of up to four long-word transfers) and update the CCR portion of the SR appropriately, because the RTE instruction expects the entire operation to have been completed if the RM bit is set and the DF bit is cleared. This is true even if the fault occurred on the first read cycle. To emulate the entire instruction, the handler must save the data and address registers for the instruction (with a MOVEM instruction, for example). Next, the handler reads and modifies (if necessary) the memory location. It clears the DF bit in the SSW of the stack frame and modifies the condition codes in the SR copy and the copies of any data or address registers required for the CAS and CAS2 instructions. Last, the handler restores the registers that it saved at the beginning of the emulation. Except for the data input buffer, the copy of the SR, and the SSW, the handler should not modify a bus fault stack frame. The only bits in the SSW that may be modified are DF, RB, and RC; all other bits, including those defined for internal use, must remain unchanged. Address error faults must be repaired in software. Address error faults can be distinguished from bus error faults by the value in the vector offset field of the format word. 6.2.3 Completing the Bus Cycles with RTE Another method of completing a faulted bus cycle is to allow the processor to rerun the bus cycles during execution of the RTE instruction that terminates the exception handler. This method cannot be used to recover from address errors. The RTE instruction is always executed. Unless the handler routine has corrected the error and cleared the fault (and cleared the RB/RC and DF bits of the SSW), the RTE instruction cannot complete the bus cycle(s). If the DF bit is still set at the time of the RTE execution, the faulted data cycle is rerun by the RTE instruction. If the FB or FC bit is set and the corresponding rerun bit (RB or RC) was not cleared by the software, the RTE reruns the associated instruction prefetch. The fault occurs again unless the cause of the fault, such as a nonresident page in a virtual memory system, has been corrected. If the RB or RC bit is set and the MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-25 Freescale Semiconductor, Inc. corresponding fault bit (FB or FC) is cleared, the associated prefetch cycle may or may not be run by the RTE instruction (depending on whether the stage is required). If a fault occurs when the RTE instruction attempts to rerun the bus cycle(s), the processor creates a new stack frame on the supervisor stack after deallocating the previous frame, and address error or bus error exception processing starts in the normal manner. Freescale Semiconductor, Inc... The read-modify-write operations of the MC68020/EC020 can also be completed by the RTE instruction that terminates the handler routine. The rerun operation, executed by the RTE instruction with the DF bit of the SSW set, reruns the entire instruction. If the cause of the error has been corrected, the handler does not need to emulate the instruction but can leave the DF bit set and execute the RTE instruction. 6.3 COPROCESSOR CONSIDERATIONS Exception handler programmers should consider carefully whether to save and restore the context of a coprocessor at the beginning and end of handler routines for exceptions that can occur during the execution of a coprocessor instruction (i.e., bus errors, interrupts, and coprocessor-related exceptions). The nature of the coprocessor and the exception handler routine determines whether or not saving the state of one or more coprocessors with the cpSAVE and cpRESTORE instructions is required. If the coprocessor allows multiple coprocessor instructions to be executed concurrently, it may require its state to be saved and restored for all coprocessor-generated exceptions, regardless of whether or not the coprocessor is accessed during the handler routine. The MC68882 floating-point coprocessor is an example of this type of coprocessor. On the other hand, the MC68881 floating-point coprocessor requires FSAVE and FRESTORE instructions within an exception handler routine only if the exception handler itself uses the coprocessor. 6.4 EXCEPTION STACK FRAME FORMATS The MC68020/EC020 provides six different stack frames for exception processing. The set of frames includes the normal four- and six-word stack frames, the four-word throwaway stack frame, the coprocessor midinstruction stack frame, and the short and long bus fault stack frames. When the MC68020/EC020 writes or reads a stack frame, it uses long-word operand transfers wherever possible. Using a long-word-aligned stack pointer with memory that is on a 32-bit port greatly enhances exception processing performance. The processor does not necessarily read or write the stack frame data in sequential order. The system software should not depend on a particular exception generating a particular stack frame. For compatibility with future devices, the software should be able to handle any type of stack frame for any type of exception. Table 6-5 summarizes the stack frames defined for the MC68020/EC020. 6-26 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 6-5. Exception Stack Frames Stack Frames 15 Exception Types (Stacked PC Points to) 0 SP STATUS REGISTER +$02 PROGRAM COUNTER 00 0 0 +$06 VECTOR OFFSET Freescale Semiconductor, Inc... FOUR-WORD STACK FRAME -- FORMAT $0 15 0 SP STATUS REGISTER +$02 PROGRAM COUNTER 00 0 1 +$06 VECTOR OFFSET THROWAWAY FOUR-WORD STACK FRAME -- FORMAT $1 15 0 SP STATUS REGISTER +$02 PROGRAM COUNTER +$06 +$08 00 1 0 VECTOR OFFSET INSTRUCTION ADDRESS SIX-WORD STACK FRAME -- FORMAT $2 15 SP 0 STATUS REGISTER +$02 10 0 1 +$06 +$08 PROGRAM COUNTER VECTOR OFFSET INSTRUCTION ADDRESS +$0C INTERNAL REGISTERS, 4 WORDS +$12 Interrupt Format Error TRAP #N Illegal Instruction A-Line Instruction F-Line Instruction Privilege Violation [Next instruction] [RTE or cpRESTORE instruction [NEXT instruction] [Illegal instruction] [A-line instruction] [F-line instruction] [First word of instruction causing Privilege Violation] Coprocessor Preinstruction [Opword of instruction that returned the 'take preinstruction' primitive] Created on Interrupt Stack during interrupt exception processing when transition from master state to interrupt state occurs [Next instruction -- same as on master stack] CHK CHK2 cpTRAPcc TRAPcc TRAPPV Trace Zero Divide MMU Configuration Coprocessor Postinstruction [Next instruction for all these exceptions] Coprocessor Midinstruction Main-Detected Protocol Violation Interrupt Detected During Coprocessor Instruction (supported with 'null come again with interrupts allowed' primitive) [Next word to be fetched from instruction stream for all these exceptions] INSTRUCTION ADDRESS is the address of the instruction that caused the exception INSTRUCTION ADDRESS is the address of the instruction that caused the exception COPROCESSOR MIDINSTRUCTION STACK FRAME (10 WORDS) -- FORMAT $9 MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 6-27 Freescale Semiconductor, Inc. Table 6-5. Exception Stack Frames (Continued) Stack Frames Exception Types (Stacked PC Points to) 15 0 SP STATUS REGISTER +$02 Freescale Semiconductor, Inc... +$06 PROGRAM COUNTER 1 01 0 VECTOR OFFSET INTERNAL REGISTER SPECIAL STATUS REGISTER INSTRUCTION PIPE STAGE C INSTRUCTION PIPE STAGE B +$08 +$0A +$0C +$0E +$10 +$12 +$14 +$16 +$18 +$1A DATA CYCLE FAULT ADDRESS +$1C +$1E INTERNAL REGISTER INTERNAL REGISTER Address Error or Bus Error -- Execution Unit at Instruction Boundary [Next instruction] Address Error or Bus Error -- Instruction Execution in Progress [Address of instruction in execution when fault occurred -- may not be the instruction that generated the faulted bus cycle] INTERNAL REGISTER INTERNAL REGISTER DATA OUTPUT BUFFER SHORT BUS FAULT STACK FRAME (16 WORDS) -- FORMAT $A 15 0 STATUS REGISTER SP +$02 +$06 +$08 +$0A +$0C +$0E +$10 +$12 +$14 +$16 +$18 +$1A +$1C PROGRAM COUNTER 1 01 1 VECTOR OFFSET INTERNAL REGISTER SPECIAL STATUS REGISTER INSTRUCTION PIPE STAGE C INSTRUCTION PIPE STAGE B DATA CYCLE FAULT ADDRESS INTERNAL REGISTER INTERNAL REGISTER DATA OUTPUT BUFFER INTERNAL REGISTER, 4 WORDS +$22 +$24 +$28 +$2A +$2C +$30 +$36 +$38 STAGE B ADDRESS INTERNAL REGISTERS, 2 WORDS DATA INPUT BUFFER INTERNAL REGISTERS, 3 WORDS VERSION # INTERNAL INFORMATION INTERNAL REGISTERS, 18 WORDS +$5A LONG BUS FAULT STACK FRAME (46 WORDS) -- FORMAT $B 6-28 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... SECTION 7 COPROCESSOR INTERFACE DESCRIPTION The M68000 family of general-purpose microprocessors provides a level of performance that satisfies a wide range of computer applications. Special-purpose hardware, however, can often provide a higher level of performance for a specific application. The coprocessor concept allows the capabilities and performance of a general-purpose processor to be enhanced for a particular application without encumbering the main processor architecture. A coprocessor can efficiently meet specific capability requirements that must typically be implemented in software by a general-purpose processor. With a generalpurpose main processor and the appropriate coprocessor(s), the processing capabilities of a system can be tailored to a specific application. The MC68020/EC020 supports the M68000 coprocessor interface described in this section. This section is intended for designers who are implementing coprocessors to interface with the MC68020/EC020. The designer of a system that uses one or more Motorola coprocessors (the MC68881 or MC68882 floating-point coprocessor, for example) does not require a detailed knowledge of the M68000 coprocessor interface. Motorola coprocessors conform to the interface described in this section. Typically, they implement a subset of the interface, and that subset is described in the coprocessor user's manual. These coprocessors execute Motorola-defined instructions that are described in the user's manual for each coprocessor. 7.1 INTRODUCTION The distinction between standard peripheral hardware and an M68000 coprocessor is important from a programming model perspective. The programming model of the main processor consists of the instruction set, register set, and memory map. An M68000 coprocessor is a device or set of devices that communicates with the main processor through the protocol defined as the M68000 coprocessor interface. The programming model for a coprocessor is different than that for a peripheral device. A coprocessor adds additional instructions and generally additional registers and data types to the programming model that are not directly supported by the main processor architecture. The additional instructions are dedicated coprocessor instructions that utilize the coprocessor capabilities. The necessary interactions between the main processor and the coprocessor that provide a given service are transparent to the programmer. That is, the programmer does not need to know the specific communication protocol between the main processor and the coprocessor because this protocol is implemented in hardware. Thus, the coprocessor can provide capabilities to the user without appearing separate from the main processor. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-1 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... In contrast, standard peripheral hardware is generally accessed through interface registers mapped into the memory space of the main processor. To use the services provided by the peripheral, the programmer accesses the peripheral registers with standard processor instructions. While a peripheral could conceivably provide capabilities equivalent to a coprocessor for many applications, the programmer must implement the communication protocol between the main processor and the peripheral necessary to use the peripheral hardware. The communication protocol defined for the M68000 coprocessor interface is described in 7.2 Coprocessor Instruction Types. The algorithms that implement the M68000 coprocessor interface are provided in the microcode of the MC68020/EC020 and are completely transparent to the MC68020/EC020 programming model. For example, floating-point operations are not implemented in the MC68020/EC020 hardware. In a system utilizing both the MC68020/EC020 and the MC68881 or MC68882 floating-point coprocessor, a programmer can use any of the instructions defined for the coprocessor without knowing that the actual computation is performed by the MC68881 or MC68882 hardware. 7.1.1 Interface Features The M68000 coprocessor interface design incorporates a number of flexible capabilities. The physical coprocessor interface uses the main processor external bus, which simplifies the interface since no special-purpose signals are involved. With the MC68020/EC020, a coprocessor uses the asynchronous bus transfer protocol. Since standard bus cycles transfer information between the main processor and the coprocessor, the coprocessor can be implemented in whatever technology is available to the coprocessor designer. A coprocessor can be implemented as a VLSI device, as a separate system board, or even as a separate computer system. Since the main processor and a M68000 coprocessor can communicate using the asynchronous bus, they can operate at different clock frequencies. The system designer can choose the speeds of a main processor and coprocessor that provide the optimum performance for a given system. Both the MC68881 and MC68882 floating-point coprocessors use the asynchronous bus handshake protocol. The M68000 coprocessor interface also facilitates the design of coprocessors. The coprocessor designer must only conform to the coprocessor interface and does not need an extensive knowledge of the architecture of the main processor. Also, the main processor can operate with a coprocessor without having explicit provisions made in the main processor for the capabilities of that coprocessor. This type of interface provides a great deal of freedom in the implementation of a given coprocessor. 7.1.2 Concurrent Operation Support The programming model for the M68000 family of microprocessors is based on sequential, nonconcurrent instruction execution, which implies that the instructions in a given sequence must appear to be executed in the order in which they occur. To maintain a uniform programming model, any coprocessor extensions should also maintain the 7-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. model of sequential, nonconcurrent instruction execution at the user level. Consequently, the programmer can assume that the images of registers and memory affected by a given instruction have been updated when the next instruction in the sequence accessing these registers or memory locations is executed. Freescale Semiconductor, Inc... The M68000 coprocessor interface provides full support of all operations necessary for nonconcurrent operation of the main processor and its associated coprocessors. Although the M68000 coprocessor interface allows concurrency in coprocessor execution, the coprocessor designer is responsible for implementing this concurrency while maintaining a programming model based on sequential nonconcurrent instruction execution. For example, if the coprocessor determines that instruction B does not use or alter resources to be altered or used by instruction A, instruction B can be executed concurrently (if the execution hardware is also available). Thus, the required instruction interdependencies and sequences of the program are always respected. The MC68882 coprocessor offers concurrent instruction execution; whereas, the MC68881 coprocessor does not. However, the MC68020/EC020 can execute instructions concurrently with coprocessor instruction execution in the MC68881. 7.1.3 Coprocessor Instruction Format The instruction set for a given coprocessor is defined by the design of that coprocessor. When a coprocessor instruction is encountered in the main processor instruction stream, the MC68020/EC020 hardware initiates communication with the coprocessor and coordinates any interaction necessary to execute the instruction with the coprocessor. A programmer needs to know only the instruction set and register set defined by the coprocessor to use the functions provided by the coprocessor hardware. The instruction set of an M68000 coprocessor uses a subset of the F-line operation words in the M68000 instruction set. The operation word is the first word of any M68000 family instruction. The F-line operation word contains ones in bits 15-12 (refer to Figure 7-1); the remaining bits are coprocessor and instruction dependent. The F-line operation word may be followed by as many extension words as are required to provide additional information necessary for the execution of the coprocessor instruction. 15 14 13 12 1 1 1 1 11 9 CpID 8 6 5 TYPE 0 TYPE DEPENDENT Figure 7-1. F-Line Coprocessor Instruction Operation Word As shown in Figure 7-1, bits 11-9 of the F-line operation word encode the coprocessor identification (CpID) field. The MC68020/EC020 uses the CpID field to indicate the coprocessor to which the instruction applies. F-line operation words, in which the CpID is zero, are not coprocessor instructions for the MC68020/EC020. Instructions with a CpID of zero and a nonzero type field are unimplemented instructions that cause the MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-3 Freescale Semiconductor, Inc. MC68020/EC020 to begin exception processing. The MC68020/EC020 never generates coprocessor interface bus cycles with the CpID equal to zero (except via the MOVES instruction). CpID codes of 000-101 are reserved for current and future Motorola coprocessors, and CpID codes of 110-111 are reserved for user-defined coprocessors. The Motorola CpID code of 001 designates the MC68881 or MC68882 floating-point coprocessor. By default, Motorola assemblers will use a CpID code of 001 when generating the instruction operation codes for the MC68881 or MC68882. Freescale Semiconductor, Inc... The encoding of bits 8-0 of the coprocessor instruction operation word is dependent on the particular instruction being implemented (refer to 7.2 Coprocessor Instruction Types). 7.1.4 Coprocessor System Interface The communication protocol between the main processor and coprocessor necessary to execute a coprocessor instruction uses a group of interface registers, CIRs, resident within the coprocessor. By accessing one of the CIRs, the MC68020/EC020 hardware initiates coprocessor instructions. The coprocessor uses a set of response primitive codes and format codes defined for the M68000 coprocessor interface to communicate status and service requests to the main processor through these registers. The CIRs are also used to pass operands between the main processor and the coprocessor. The CIR set, response primitives, and format codes are discussed in 7.3 Coprocessor Interface Register Set and 7.4 Coprocessor Response Primitives. 7.1.4.1 COPROCESSOR CLASSIFICATION. M68000 coprocessors can be classified into two categories depending on their bus interface capabilities. The first category, non-DMA coprocessors, consists of coprocessors that always operate as bus slaves. The second category, DMA coprocessors, consists of coprocessors that operate as bus slaves while communicating with the main processor across the coprocessor interface. These coprocessors also have the ability to operate as bus masters, directly controlling the system bus. If the operation of a coprocessor does not require a large portion of the available bus bandwidth or has special requirements not directly satisfied by the main processor, that coprocessor can be efficiently implemented as a non-DMA coprocessor. Since non-DMA coprocessors always operate as bus slaves, all external bus-related functions that the coprocessor requires are performed by the main processor. The main processor transfers operands from the coprocessor by reading the operand from the appropriate CIR and then writing the operand to a specified effective address with the appropriate address space specified on the FC2-FC0. Likewise, the main processor transfers operands to the coprocessor by reading the operand from a specified effective address (and address space) and then writing that operand to the appropriate CIR using the coprocessor interface. The bus interface circuitry of a coprocessor operating as a bus slave is not as complex as that of a device operating as a bus master. 7-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. To improve the efficiency of operand transfers between memory and the coprocessor, a coprocessor that requires a relatively high amount of bus bandwidth or has special bus requirements can be implemented as a DMA coprocessor. The DMA coprocessor provides all control, address, and data signals necessary to request and obtain the bus and then performs DMA transfers using the bus. DMA coprocessors, however, must still act as bus slaves when they require information or services of the main processor using the M68000 coprocessor interface protocol. Freescale Semiconductor, Inc... 7.1.4.2 PROCESSOR-COPROCESSOR INTERFACE. Figure 7-2 is a block diagram of the signals involved in an asynchronous non-DMA M68000 coprocessor interface. Since the CpID on signals A15-A13 of the address bus is used with other address signals to select the coprocessor, the system designer can use several coprocessors of the same type and assign a unique CpID to each one. FC2-FC0 A19-A13 COPROCESSOR DECODE LOGIC * CS COPROCESSOR AS MAIN PROCESSOR MC68020/EC020 DS R/W DSACK1 / DSACK0 ASYNCHRONOUS BUS INTERFACE LOGIC A4-A1 D31-D0 FC2-FC0 = 111 A19-A16 = 0010 A15-A13 = xxx A4-A1 = rrrr CPU SPACE CYCLE COPROCESSOR ACCESS IN CPU SPACE COPROCESSOR IDENTIFICATION COPROCESSOR INFERFACE REGISTER SELECTOR *Chip select logic may be integrated into the coprocessor. Address lines not specified above are "0" during coprocessor access. Figure 7-2. Asynchronous Non-DMA M68000 Coprocessor Interface Signal Usage The MC68020/EC020 accesses the registers in the CIR set using standard asynchronous bus cycles. Thus, the bus interface implemented by a coprocessor for its interface register set must satisfy the MC68020/EC020 address, data, and control signal timing. The MC68020/EC020 bus operation is described in detail in Section 5 Bus Operation. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-5 Freescale Semiconductor, Inc. During coprocessor instruction execution, the MC68020/EC020 executes CPU space bus cycles to access the CIR set. The MC68020/EC020 asserts FC2-FC0, identifying a CPU space bus cycle. The CIR set is mapped into CPU space in the same manner that a peripheral interface register set is generally mapped into data space. The information encoded on FC2-FC0 and the address bus of the MC68020/EC020 during a coprocessor access is used to generate the chip select signal for the coprocessor being accessed. Other address lines select a register within the interface set. The information encoded on the function code and address lines of the MC68020/EC020 during a coprocessor access is illustrated in Figure 7-3. FUNCTION CODE Freescale Semiconductor, Inc... 2 1 1 ADDRESS BUS 0 31 1 0 20 19 0 0 0 0 0 0 0 0 0 0 0 0 16 15 0 1 0 13 12 CpID 0 5 0 0 0 0 0 0 4 0 0 CIR CPU SPACE TYPE FIELD Figure 7-3. MC68020/EC020 CPU Space Address Encodings Signals A19-A16 of the MC68020/EC020 address bus specify the CPU space cycle type for a CPU space bus cycle. The types of CPU space cycles currently defined for the MC68020/EC020 are interrupt acknowledge, breakpoint acknowledge, module support operations, and coprocessor access cycles. CPU space type $2 (A19-A16 = 0010) specifies a coprocessor access cycle. A15-A13 specify the CpID code for the coprocessor being accessed. This code is transferred from bits 11-9 of the coprocessor instruction operation word (refer to Figure 7-1) to the address bus during each coprocessor access. Thus, decoding the MC68020/EC020 FC2-FC0 and A19-A13 signals provides a unique chip select signal for a given coprocessor. The FC2-FC0 and A19-A16 signals indicate a coprocessor access; A15-A13 indicate which of the possible eight coprocessors (000-111) is being accessed. Bits A31-A20 and A12-A5 of the MC68020 address bus and bits A23-A20 and A12-A5 of the MC68EC020 address bus are always zero during a coprocessor access. 7.1.4.3 COPROCESSOR INTERFACE REGISTER SELECTION. Figure 7-4 shows that the value on the MC68020/EC020 address bus during a coprocessor access addresses a unique region of the main processor's CPU address space. Signals A4-A0 of the MC68020/EC020 address bus select the CIR being accessed. The register map for the M68000 coprocessor interface is shown in Figure 7-5. The individual registers are described in detail in 7.3 Coprocessor Interface Register Set. 7-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. CPU SPACE ADDRESS $20000 INTERFACE REGISTER SET $2001F RESERVED ADDRESS SPACE FOR COPROCESSOR WITH CpID = 0 $22000 INTERFACE REGISTER SET $2201F RESERVED ADDRESS SPACE FOR COPROCESSOR WITH CpID = 1 $24000 Freescale Semiconductor, Inc... $2E000 INTERFACE REGISTER SET $2E01F RESERVED ADDRESS SPACE FOR COPROCESSOR WITH CpID = 7 Figure 7-4. Coprocessor Address Map in MC68020/EC020 CPU Space 31 16 15 0 $00 RESPONSE CONTROL $04 SAVE RESTORE $08 OPERATION WORD COMMAND $0C (RESERVED) CONDITION $10 $14 OPERAND REGISTER SELECT (RESERVED) $18 INSTRUCTION ADDRESS $1C OPERAND ADDRESS Figure 7-5. Coprocessor Interface Register Set Map 7.2 COPROCESSOR INSTRUCTION TYPES The M68000 coprocessor interface supports four categories of coprocessor instructions: general, conditional, context save, and context restore. The category name indicates the type of operations provided by the coprocessor instructions in the category. The instruction category also determines the CIR accessed by the MC68020/EC020 to initiate instruction and communication protocols between the main processor and the coprocessor necessary for instruction execution. During the execution of instructions in the general or conditional categories, the coprocessor uses the set of coprocessor response primitive codes defined for the M68000 coprocessor interface to request services from and indicate status to the main processor. During the execution of the instructions in the context save and context MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-7 Freescale Semiconductor, Inc. restore categories, the coprocessor uses the set of coprocessor format codes defined for the M68000 coprocessor interface to indicate its status to the main processor. 7.2.1 Coprocessor General Instructions The coprocessor general instruction category contains data processing instructions and other general-purpose instructions for a given coprocessor. 7.2.1.1 FORMAT. Figure 7-6 shows the format of a coprocessor general instruction. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 0 0 0 5 0 EFFECTIVE ADDRESS Freescale Semiconductor, Inc... COPROCESSOR COMMAND OPTIONAL EFFECTIVE ADDRESS OR COPROCESSOR-DEFINED EXTENSION WORDS Figure 7-6. Coprocessor General Instruction Format (cpGEN) The mnemonic cpGEN is a generic mnemonic used in this discussion for all general instructions. The mnemonic of a specific general instruction usually suggests the type of operation it performs and the coprocessor to which it applies. The actual mnemonic and syntax used to represent a coprocessor instruction is determined by the syntax of the assembler or compiler that generates the object code. A coprocessor general instruction consists of at least two words. The first word of the instruction is an F-line operation code (bits 15-12 = 1111). The CpID field of the F-line operation code is used during the coprocessor access to indicate which coprocessor in the system executes the instruction. During accesses to the CIRs (refer to 7.1.4.2 Processor-Coprocessor Interface), the processor places the CpID on address lines A15-A13. Bits 8-6 = 000 of the first word of an instruction indicate that the instruction is in the general instruction category. Bits 5-0 of the F-line operation code sometimes encode a standard M68000 effective address specifier (refer to M68000PM/AD, M68000 Family Programmer's Reference Manual ). During the execution of a cpGEN instruction, the coprocessor can use a coprocessor response primitive to request that the MC68020/EC020 perform an effective address calculation necessary for that instruction. Using the effective address specifier field of the F-line operation code, the processor then determines the effective addressing mode. If a coprocessor never requests effective address calculation, bits 5-0 can have any value (don't cares). The second word of the general type instruction is the coprocessor command word. The main processor writes this command word to the command CIR to initiate execution of the instruction by the coprocessor. An instruction in the coprocessor general instruction category optionally includes a number of extension words following the coprocessor command word. These words can provide additional information required for the coprocessor instruction. For example, if 7-8 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. the coprocessor requests that the MC68020/EC020 calculate an effective address during coprocessor instruction execution, information required for the calculation must be included in the instruction format as effective address extension words. Freescale Semiconductor, Inc... 7.2.1.2 PROTOCOL. The execution of a cpGEN instruction follows the protocol shown in Figure 7-7. The main processor initiates communication with the coprocessor by writing the instruction command word to the command CIR. The coprocessor decodes the command word to begin processing the cpGEN instruction. Coprocessor design determines the interpretation of the coprocessor command word; the MC68020/EC020 does not attempt to decode it. While the coprocessor is executing an instruction, it requests any required services from and communicates status to the main processor by placing coprocessor response primitive codes in the response CIR. After writing to the command CIR, the main processor reads the response CIR and responds appropriately. When the coprocessor has completed the execution of an instruction or no longer needs the services of the main processor to execute the instruction, it provides a response to release the main processor. The main processor can then execute the next instruction in the instruction stream. However, if a trace exception is pending, the MC68020/EC020 does not terminate communication with the coprocessor until the coprocessor indicates that it has completed all processing associated with the cpGEN instruction (refer to 7.5.2.5 Trace Exceptions). The coprocessor interface protocol shown in Figure 7-7 allows the coprocessor to define the operation of each coprocessor general type instruction. That is, the main processor initiates the instruction execution by writing the instruction command word to the command CIR and by reading the response CIR to determine its next action. The execution of the coprocessor instruction is then defined by the internal operation of the coprocessor and by its use of response primitives to request services from the main processor. This instruction protocol allows a wide range of operations to be implemented in the general instruction category. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-9 Freescale Semiconductor, Inc. MAIN PROCESSOR COPROCESSOR M1 RECOGNIZE COPROCESSOR INSTRUCTION F-LINE OPERATION WORD Freescale Semiconductor, Inc... M2 WRITE COPROCESSOR COMMAND WORD TO COMMAND CIR M3 READ COPROCESSOR RESPONSE PRIMITIVE CODE FROM RESPONSE CIR 1) PERFORM SERVICE REQUESTED BY RESPONSE PRIMITIVE 2) IF (COPROCESSOR RESPONSE PRIMITIVE INDICATES "COME AGAIN") GO TO M3 (SEE NOTE 1) M4 PROCEED WITH EXECUTION OF NEXT INSTRUCTION (SEE NOTE 2) C1 DECODE COMMAND WORD AND INITIATE COMMAND EXECUTION C2 WHILE (MAIN PROCESSOR SERVICE IS REQUIRED) DO STEPS 1) AND 2) BELOW 1) REQUEST SERVICE BY PLACING APPROPRIATE RESPONSE PRIMITIVE CODE IN RESPONSE CIR 2) RECEIVE SERVICE FROM MAIN PROCESSOR C3 REFLECT "NO COME AGAIN" IN RESPONSE CIR C4 COMPLETE COMMAND EXECUTION C5 REFLECT "PROCESSING FINISHED" STATUS IN RESPONSE CIR NOTES: 1. "Come Again" indicates that further service of the main processor is being requested by the coprocessor. 2. The next instruction should be the operation word pointed to by the ScanPC at this point. The operation of the MC68020/EC020 ScanPC is discussed in 7.4.1 ScanPC. Figure 7-7. Coprocessor Interface Protocol for General Category Instructions 7.2.2 Coprocessor Conditional Instructions The conditional instruction category provides program control based on the operations of the coprocessor. The coprocessor evaluates a condition and returns a true/false indicator to the main processor. The main processor completes the execution of the instruction based on this true/false condition indicator. The implementation of instructions in the conditional category promotes efficient use of both the main processor and the coprocessor hardware. The condition specified for the instruction is related to the coprocessor operation and is therefore evaluated by the coprocessor. However, the instruction completion following the condition evaluation is directly related to the operation of the main processor. The main processor performs the change of flow, the setting of a byte, or the TRAP operation, since its architecture explicitly implements these operations for its instruction set. Figure 7-8 shows the protocol for a conditional category coprocessor instruction. The main processor initiates execution of an instruction in this category by writing a condition selector to the condition CIR. The coprocessor decodes the condition selector to determine the condition to evaluate. The coprocessor can use response primitives to request that the main processor provide services required for the condition evaluation. 7-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. After evaluating the condition, the coprocessor returns a true/false indicator to the main processor by placing a null primitive (refer to 7.4.4 Null Primitive) in the response CIR. The main processor completes the coprocessor instruction execution when it receives the condition indicator from the coprocessor. MAIN PROCESSOR COPROCESSOR M1 RECOGNIZE COPROCESSOR INSTRUCTION F-LINE OPERATION WORD Freescale Semiconductor, Inc... M2 CO WRITE COPROCESSOR CONDITION SELECTOR TO NDITION CIR M3 READ COPROCESSOR RESPONSE PRIMITIVE CODE FROM RESPONSE CIR 1) PERFORM SERVICE REQUESTED BY RESPONSE PRIMITIVE 2) IF (COPROCESSOR RESPONSE PRIMITIVE INDICATES "COME AGAIN") GO TO M3 (SEE NOTE) C1 DECODE COMMAND WORD AND INITIATE COMMAND EXECUTION C2 WHILE (MAIN PROCESSOR SERVICE IS REQUIRED) DO STEPS 1) AND 2) BELOW 1) REQUEST SERVICE BY PLACING APPROPRIATE RESPONSE PRIMITIVE CODE IN RESPONSE CIR 2) RECEIVE SERVICE FROM MAIN PROCESSOR C3 COMPLETE CONDITION EVALUATION C4 REFLECT "NO COME AGAIN" STATUS WITH TRUE/FALSE CONDITION INDICATOR IN RESPONSE CIR M4 COMPLETE EXECUTION OF INSTRUCTION BASED ON THE TRUE/FALSE CONDITION INDICATOR RETURNED IN THE RESPONSE CIR NOTE: All coprocessor response primitives, except the Null primitive, that allow the "Come Again" primitive attribute must indicate "Come Again" when used during the execution of a conditional category instruction. If a "Come Again" attribute is not indicated in one of these primitives, the main processor will initiate protocol violation exception processing (see 7.5.2.1 Protocol Violations). Figure 7-8. Coprocessor Interface Protocol for Conditional Category Instructions MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-11 Freescale Semiconductor, Inc. 7.2.2.1 BRANCH ON COPROCESSOR CONDITION INSTRUCTION. The conditional instruction category includes two formats of the M68000 family branch instruction. These instructions branch on conditions related to the coprocessor operation. They execute similarly to the conditional branch instructions provided in the M68000 family instruction set. Freescale Semiconductor, Inc... 7.2.2.1.1 Format. Figure 7-9 shows the format of the branch on coprocessor condition instruction that provides a word-length displacement. Figure 7-10 shows the format of this instruction that includes a long-word displacement. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 0 1 0 5 0 CONDITION SELECTOR OPTIONAL COPROCESSOR-DEFINED EXTENSION WORDS DISPLACEMENT Figure 7-9. Branch on Coprocessor Condition Instruction Format (cpBcc.W) 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 0 1 1 5 0 CONDITION SELECTOR OPTIONAL COPROCESSOR-DEFINED EXTENSION WORDS DISPLACEMENT -- HIGH DISPLACEMENT -- LOW Figure 7-10. Branch on Coprocessor Condition Instruction Format (cpBcc.L) The first word of the branch on coprocessor condition instruction is the F-line operation word. Bits 15-12 = 1111 and bits 11-9 contain the CpID code of the coprocessor that is to evaluate the condition. The value in bits 8-6 identifies either the word or the long-word displacement format of the branch instruction, which is specified by the cpBcc.W or cpBcc.L mnemonic, respectively. Bits 5-0 of the F-line operation word contain the coprocessor condition selector field. The MC68020/EC020 writes the entire operation word to the condition CIR to initiate execution of the branch instruction by the coprocessor. The coprocessor uses bits 5-0 to determine which condition to evaluate. If the coprocessor requires additional information to evaluate the condition, the branch instruction format can include this information in extension words. Following the F-line operation word, the number of extension words is determined by the coprocessor design. The final word(s) of the cpBcc instruction format contains the displacement used by the main processor to calculate the destination address when the branch is taken. 7.2.2.1.2 Protocol. Figure 7-8 shows the protocol for the cpBcc.L and cpBcc.W instructions. The main processor initiates the instruction by writing the F-line operation word to the condition CIR to transfer the condition selector to the coprocessor. The main 7-12 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... processor then reads the response CIR to determine its next action. The coprocessor can MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-13 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... return a response primitive to request services necessary to evaluate the condition. If the coprocessor returns the false condition indicator, the main processor executes the next instruction in the instruction stream. If the coprocessor returns the true condition indicator, the main processor adds the displacement to the MC68020/EC020 scanPC (refer to 7.4.1 ScanPC) to determine the address of the next instruction for the main processor to execute. The scanPC must be pointing to the location of the first word of the displacement in the instruction stream when the address is calculated. The displacement is a twoscomplement integer that can be either a 16-bit word or a 32-bit long word. The main processor sign-extends the 16-bit displacement to a long-word value for the destination address calculation. 7.2.2.2 SET ON COPROCESSOR CONDITION INSTRUCTION. The set on coprocessor condition instruction sets or resets a flag (a data alterable byte) according to a condition evaluated by the coprocessor. The operation of this instruction type is similar to the operation of the Scc instruction in the M68000 family instruction set. Although the Scc instruction and the cpScc instruction do not explicitly cause a change of program flow, they are often used to set flags that control program flow. 7.2.2.2.1 Format. Figure 7-11 shows the format of the set on coprocessor condition instruction, denoted by the cpScc mnemonic. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 0 0 1 5 RESERVED 0 EFFECTIVE ADDRESS CONDITION SELECTOR OPTIONAL COPROCESSOR-DEFINED EXTENSION WORDS OPTIONAL EFFECTIVE ADDRESS EXTENSION WORDS (0-5 WORDS) Figure 7-11. Set on Coprocessor Condition Instruction Format (cpScc) The first word of the cpScc instruction, the F-line operation word, contains the CpID field in bits 11-9 and 001 in bits 8-6 to identify the cpScc instruction. Bits 5-0 of the F-line operation word are used to encode an M68000 family effective addressing mode (refer to M68000PM/AD, M68000 Family Programmer's Reference Manual). The second word of the cpScc instruction format contains the coprocessor condition selector field in bits 5-0. Bits 15-6 of this word are reserved by Motorola and should be zero to ensure compatibility with future M68000 products. This word is written to the condition CIR to initiate execution of the cpScc instruction. If the coprocessor requires additional information to evaluate the condition, the instruction can include extension words to provide this information. The number of these extension words, which follow the word containing the coprocessor condition selector field, is determined by the coprocessor design. 7-14 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The final portion of the cpScc instruction format contains zero to five effective address extension words. These words contain any additional information required to calculate the effective address specified by bits 5-0 of the F-line operation word. 7.2.2.2.2 Protocol. Figure 7-8 shows the protocol for the cpScc instruction. The MC68020/EC020 transfers the condition selector to the coprocessor by writing the word following the F-line operation word to the condition CIR. The main processor then reads the response CIR to determine its next action. The coprocessor can return a response primitive to request services necessary to evaluate the condition. The operation of the cpScc instruction depends on the condition evaluation indicator returned to the main processor by the coprocessor. When the coprocessor returns the false condition indicator, the main processor evaluates the effective address specified by bits 5-0 of the F-line operation word and sets the byte at that effective address to FALSE (all bits cleared). When the coprocessor returns the true condition indicator, the main processor sets the byte at the effective address to TRUE (all bits set to one). 7.2.2.3 TEST COPROCESSOR CONDITION, DECREMENT, AND BRANCH INSTRUCTION. The operation of the test coprocessor condition, decrement, and branch instruction is similar to that of the DBcc instruction provided in the M68000 family instruction set. This operation uses a coprocessor-evaluated condition and a loop counter in the main processor. It is useful for implementing DO UNTIL constructs used in many high-level languages. 7.2.2.3.1 Format. Figure 7-12 shows the format of the test coprocessor condition, decrement, and branch instruction, denoted by the cpDBcc mnemonic. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 5 4 3 0 0 1 0 0 1 (RESERVED) 2 0 REGISTER CONDITION SELECTOR OPTIONAL COPROCESSOR-DEFINED EXTENSION WORDS DISPLACEMENT Figure 7-12. Test Coprocessor Condition, Decrement, and Branch Instruction Format (cpDBcc) The first word of the cpDBcc instruction, F-line operation word, contains the CpID field in bits 11-9 and 001001 in bits 8-3 to identify the cpDBcc instruction. Bits 2-0 of this operation word specify the main processor data register used as the loop counter during the execution of the instruction. The second word of the cpDBcc instruction format contains the coprocessor condition selector field in bits 5-0 and should contain zeros in bits 15-6 (reserved by Motorola) to maintain compatibility with future M68000 products. This word is written to the condition CIR to initiate execution of the cpDBcc instruction. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-15 Freescale Semiconductor, Inc. If the coprocessor requires additional information to evaluate the condition, the cpDBcc instruction can include this information in extension words. These extension words follow the word containing the coprocessor condition selector field in the cpDBcc instruction format. Freescale Semiconductor, Inc... The last word of the instruction contains the displacement for the cpDBcc instruction. This displacement is a twos-complement 16-bit value that is sign-extended to long-word size when it is used in a destination address calculation. 7.2.2.3.2 Protocol. Figure 7-8 shows the protocol for the cpDBcc instructions. The MC68020/EC020 transfers the condition selector to the coprocessor by writing the word following the operation word to the condition CIR. The main processor then reads the response CIR to determine its next action. The coprocessor can use a response primitive to request any services necessary to evaluate the condition. If the coprocessor returns the true condition indicator, the main processor executes the next instruction in the instruction stream. If the coprocessor returns the false condition indicator, the main processor decrements the low-order word of the register specified by bits 2-0 of the F-line operation word. If this register contains minus one (-1) after being decremented, the main processor executes the next instruction in the instruction stream. If the register does not contain minus one (-1) after being decremented, the main processor branches to the destination address to continue instruction execution. The MC68020/EC020 adds the displacement to the scanPC (refer to 7.4.1 ScanPC) to determine the address of the next instruction. The scanPC must point to the 16-bit displacement in the instruction stream when the destination address is calculated. 7.2.2.4 TRAP ON COPROCESSOR CONDITION INSTRUCTION. The trap on coprocessor condition instruction allows the programmer to initiate exception processing based on conditions related to the coprocessor operation. 7.2.2.4.1 Format. Figure 7-13 shows the format of the trap on coprocessor condition instruction, denoted by the cpTRAPcc mnemonic. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 5 4 3 0 0 1 1 1 1 (RESERVED) 2 0 OPMODE CONDITION SELECTOR OPTIONAL COPROCESSOR-DEFINED EXTENSION WORDS OPTIONAL WORD OR LONG-WORD OPERAND Figure 7-13. Trap on Coprocessor Condition Instruction Format (cpTRAPcc) The first word of the cpTRAPcc instruction, the F-line operation word contains the CpID field in bits 11-9 and 001111 in bits 8-3 to identify the cpTRAPcc instruction. Bits 2-0 of the cpTRAPcc F-line operation word specify the opmode, which selects the instruction format. The instruction format can include zero, one, or two operand words. 7-16 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The second word of the cpTRAPcc instruction format contains the coprocessor condition selector in bits 5-0 and should contain zeros in bits 15-6 (these bits are reserved by Motorola) to maintain compatibility with future M68000 products. This word is written to the condition CIR to initiate execution of the cpTRAPcc instruction. Freescale Semiconductor, Inc... If the coprocessor requires additional information to evaluate a condition, the instruction can include this information in extension words. These extension words follow the word containing the coprocessor condition selector field in the cpTRAPcc instruction format. The operand words of the cpTRAPcc F-line operation word follow the coprocessor-defined extension words. These operand words are not explicitly used by the MC68020/EC020, but can be used to contain information referenced by the cpTRAPcc exception handling routines. The valid encodings for bits 2-0 of the F-line operation word and the corresponding numbers of operand words are listed in Table 7-1. Other encodings of these bits are invalid for the cpTRAPcc instruction. Table 7-1. cpTRAPcc Opmode Encodings Opmode Operand Words in Instruction Format 010 One 011 Two 100 Zero 7.2.2.4.2 Protocol. Figure 7-8 shows the protocol for the cpTRAPcc instructions. The MC68020/EC020 transfers the condition selector to the coprocessor by writing the word following the operation word to the condition CIR. The main processor then reads the response CIR to determine its next action. The coprocessor can return a response primitive to request any services necessary to evaluate the condition. If the coprocessor returns the true condition indicator, the main processor initiates exception processing for the cpTRAPcc exception (refer to 7.5.2.4 cpTRAPcc Instruction Traps). If the coprocessor returns the false condition indicator, the main processor executes the next instruction in the instruction stream. 7.2.3 Coprocessor Context Save and Restore Instructions The coprocessor context save and context restore instruction categories in the M68000 coprocessor interface support multitasking programming environments. In a multitasking environment, the context of a coprocessor may need to be changed asynchronously with respect to the operation of that coprocessor. That is, the coprocessor may be interrupted at any point in the execution of an instruction in the general or conditional category to begin context change operations. In contrast to the general and conditional instruction categories, the context save and context restore instruction categories do not use the coprocessor response primitives. A set of format codes defined by the M68000 coprocessor interface communicates status MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-17 Freescale Semiconductor, Inc. information to the main processor during the execution of these instructions. These coprocessor format codes are discussed in detail in 7.2.3.2 Coprocessor Format Words. Freescale Semiconductor, Inc... 7.2.3.1 COPROCESSOR INTERNAL STATE FRAMES. The context save (cpSAVE) and context restore (cpRESTORE) instructions transfer an internal coprocessor state frame between memory and a coprocessor. This internal coprocessor state frame represents the state of coprocessor operations. Using the cpSAVE and cpRESTORE instructions, it is possible to interrupt coprocessor operation, save the context associated with the current operation, and initiate coprocessor operations with a new context. A cpSAVE instruction stores a coprocessor internal state frame as a sequence of longword entries in memory. Figure 7-14 shows the format of a coprocessor state frame. The format and length fields of the coprocessor state frame format comprise the format word. During execution of the cpSAVE instruction, the MC68020/EC020 calculates the state frame effective address from information in the operation word of the instruction and stores a format word at this effective address. The processor writes the long words that form the coprocessor state frame to descending memory addresses, beginning with the address specified by the sum of the effective address and the length field multiplied by four. During execution of the cpRESTORE instruction, the MC68020/EC020 reads the state frame from ascending addresses beginning with the effective address specified in the instruction operation word. SAVE RESTORE ORDER ORDER 31 0 0 n 1 n-1 2 n-2 3 1 n 24 FORMAT 23 16 15 LENGTH 0 (UNUSED, RESERVED) COPROCESSOR-DEPENDENT INFORMATION Figure 7-14. Coprocessor State Frame Format in Memory The processor stores the coprocessor format word at the lowest address of the state frame in memory, and this word is the first word transferred for both the cpSAVE and cpRESTORE instructions. The word following the format word does not contain information relevant to the coprocessor state frame, but serves to keep the information in the state frame a multiple of four bytes in size. The number of entries following the format word (at higher addresses) is determined by the format word length for a given coprocessor state. 7-18 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The information in a coprocessor state frame describes a context of operation for that coprocessor. This description of a coprocessor context includes the program invisible state information and, optionally, the program visible state information. The program invisible state information consists of any internal registers or status information that cannot be accessed by the program but is necessary for the coprocessor to continue its operation at the point of suspension. Program visible state information includes the contents of all registers that appear in the coprocessor programming model and that can be directly accessed using the coprocessor instruction set. The information saved by the cpSAVE instruction must include the program invisible state information. If cpGEN instructions are provided to save the program visible state of the coprocessor, the cpSAVE and cpRESTORE instructions should only transfer the program invisible state information to minimize interrupt latency during a save or restore operation. 7.2.3.2 COPROCESSOR FORMAT WORDS. The coprocessor communicates status information to the main processor during the execution of cpSAVE and cpRESTORE instructions using coprocessor format words. The format words defined for the M68000 coprocessor interface are listed in Table 7-2. Table 7-2. Coprocessor Format Word Encodings Format Code Length Meaning $00 $xx Empty/Reset $01 $xx Not Ready, Come Again $02 $xx Invalid Format $03-$OF $xx Undefined, Reserved $10-$FF Length Valid Format, Coprocessor Defined xx--Don't care The upper byte of the coprocessor format word contains the code used to communicate coprocessor status information to the main processor. The MC68020/EC020 recognizes four types of format words: empty/reset, not ready, invalid format, and valid format. The MC68020/EC020 interprets the reserved format codes ($03-$0F) as invalid format words. The lower byte of the coprocessor format word specifies the size in bytes (which must be a multiple of four) of the coprocessor state frame. This value is only relevant when the code byte contains the valid format code (refer to 7.2.3.2.4 Valid Format Word). 7.2.3.2.1 Empty/Reset Format Word. The coprocessor returns the empty/reset format code during a cpSAVE instruction to indicate that the coprocessor contains no userspecific information. That is, no coprocessor instructions have been executed since either a previous cpRESTORE of an empty/reset format code or the previous hardware reset. If the main processor reads the empty/reset format word from the save CIR during the initiation of a cpSAVE instruction, it stores the format word at the effective address specified in the cpSAVE instruction and executes the next instruction. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-19 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... When the main processor reads the empty/reset format word from memory during the execution of the cpRESTORE instruction, it writes the format word to the restore CIR. The main processor then reads the restore CIR and, if the coprocessor returns the empty/reset format word, executes the next instruction. The main processor can then initialize the coprocessor by writing the empty/reset format code to restore the CIR. When the coprocessor receives the empty/reset format code, it terminates any current operations and waits for the main processor to initiate the next coprocessor instruction. In particular, after the cpRESTORE of the empty/reset format word, the execution of a cpSAVE should cause the empty/reset format word to be returned when a cpSAVE instruction is executed before any other coprocessor instructions. Thus, an empty/reset state frame consists only of the format word and the following reserved word in memory (refer to Figure 7-14). 7.2.3.2.2 Not-Ready Format Word. When the main processor initiates a cpSAVE instruction by reading the save CIR, the coprocessor can delay the save operation by returning a not-ready format word. The main processor then services any pending interrupts and reads the save CIR again. The not-ready format word delays the save operation until the coprocessor is ready to save its internal state. The cpSAVE instruction can suspend execution of a general or conditional coprocessor instruction; the coprocessor can resume execution of the suspended instruction when the appropriate state is restored with a cpRESTORE. If no further main processor services are required to complete coprocessor instruction execution, it may be more efficient to complete the instruction and thus reduce the size of the saved state. The coprocessor designer should consider the efficiency of completing the instruction or of suspending and later resuming the instruction when the main processor executes a cpSAVE instruction. When the main processor initiates a cpRESTORE instruction by writing a format word to the restore CIR, the coprocessor should usually terminate any current operations and restore the state frame supplied by the main processor. Thus, the not-ready format word should usually not be returned by the coprocessor during the execution of a cpRESTORE instruction. If the coprocessor must delay the cpRESTORE operation for any reason, it can return the not-ready format word when the main processor reads the restore CIR. If the main processor reads the not-ready format word from the restore CIR during the cpRESTORE instruction, it reads the restore CIR again without servicing any pending interrupts. 7.2.3.2.3 Invalid Format Word. When the format word placed in the restore CIR to initiate a cpRESTORE instruction does not describe a valid coprocessor state frame, the coprocessor returns the invalid format word in the restore CIR. When the main processor reads this format word during the cpRESTORE instruction, it sets the abort bit in the control CIR and initiates format error exception processing. A coprocessor usually should not place an invalid format word in the save CIR when the main processor initiates a cpSAVE instruction. A coprocessor, however, may not be able to support the initiation of a cpSAVE instruction while it is executing a previously initiated cpSAVE or cpRESTORE instruction. In this situation, the coprocessor can return the invalid format word when the main processor reads the save CIR to initiate the cpSAVE instruction while either another cpSAVE or cpRESTORE instruction is executing. If the 7-20 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. main processor reads an invalid format word from the save CIR, it writes the abort mask to the control CIR and initiates format error exception processing (refer to 7.5.1.5 Format Errors). Freescale Semiconductor, Inc... 7.2.3.2.4 Valid Format Word. When the main processor reads a valid format word from the save CIR during the cpSAVE instruction, it uses the length field to determine the size of the coprocessor state frame to save. The length field in the lower eight bits of a format word is relevant only in a valid format word. During the cpRESTORE instruction, the main processor uses the length field in the format word read from the effective address in the instruction to determine the size of the coprocessor state frame to restore. The length field of a valid format word, representing the size of the coprocessor state frame, must contain a multiple of four. If the main processor detects a value that is not a multiple of four in a length field during the execution of a cpSAVE or cpRESTORE instruction, the main processor writes the abort mask (refer to 7.2.3.2.3 Invalid Format Word) to the control CIR and initiates format error exception processing. 7.2.3.3 COPROCESSOR CONTEXT SAVE INSTRUCTION. The M68000 coprocessor context save instruction category consists of one instruction. The coprocessor context save instruction, denoted by the cpSAVE mnemonic, saves the context of a coprocessor dynamically without relation to the execution of coprocessor instructions in the general or conditional instruction categories. During the execution of a cpSAVE instruction, the coprocessor communicates status information to the main processor by using the coprocessor format codes. 7.2.3.3.1 Format. Figure 7-15 shows the format of the cpSAVE instruction. The first word of the instruction, the F-line operation word, contains the CpID code in bits 11-9 and an M68000 effective address code in bits 5-0. The effective address encoded in the cpSAVE instruction is the address at which the state frame associated with the current context of the coprocessor is saved in memory. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 1 0 0 5 0 EFFECTIVE ADDRESS EFFECTIVE ADDRESS EXTENSION WORDS (0-5 WORDS) Figure 7-15. Coprocessor Context Save Instruction Format (cpSAVE) The control alterable and predecrement addressing modes are valid for the cpSAVE instruction. Other addressing modes cause the MC68020/EC020 to initiate F-line emulator exception processing as described in 7.5.2.2 F-Line Emulator Exceptions. The instruction can include as many as five effective address extension words following the F-line operation word. These words contain any additional information required to calculate the effective address specified by bits 5-0 of the F-line operation word. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-21 Freescale Semiconductor, Inc. 7.2.3.3.2 Protocol. Figure 7-16 shows the protocol for the coprocessor context save instruction. The main processor initiates execution of the cpSAVE instruction by reading the save CIR. Thus, the cpSAVE instruction is the only coprocessor instruction that begins by reading from a CIR. All other coprocessor instructions write to a CIR to initiate execution of the instruction by the coprocessor. The coprocessor communicates status information associated with the context save operation to the main processor by placing coprocessor format codes in the save CIR. MAIN PROCESSOR COPROCESSOR Freescale Semiconductor, Inc... M1 RECOGNIZE COPROCESSOR INSTRUCTION F-LINE OPERATION WORD M2 READ SAVE CIR TO INITIATE THE cpSAVE INSTRUCTION M3 IF (FORMAT = NOT READY) DO STEPS 1) AND 2) BELOW 1) SERVICE PENDING INTERRUPTS 2) GO TO M2 M4 EVALUATE EFFECTIVE ADDRESS SPECIFIED IN F-LINE OPWORD AND STORE FORMAT WORD AT EFFECTIVE ADDRESS M5 IF (FORMAT = EMPTY) GO TO M6 ELSE, TRANSFER NUMBER OF BYTES INDICATED IN FORMAT WORD FROM OPERAND CIR TO EFFECTIVE ADDRESS M6 PROCEED WITH EXECUTION OF NEXT INSTRUCTION Figure 7-16. Coprocessor Context Save Instruction Protocol If the coprocessor is not ready to suspend its current operation when the main processor reads the save CIR, it returns a not-ready format code. The main processor services any pending interrupts and then reads the save CIR again. After placing the not-ready format code in the save CIR, the coprocessor should either suspend or complete the instruction it is currently executing. Once the coprocessor has suspended or completed the instruction it is executing, it places a format code representing the internal coprocessor state in the save CIR. When the main processor reads the save CIR, it transfers the format word to the effective address specified in the cpSAVE instruction. The lower byte of the coprocessor format word specifies the number of bytes of state information, not including the format word and associated null word, to be transferred from the coprocessor to the effective address specified. If the state information is not a multiple of four bytes in size, the MC68020/EC020 initiates format error exception processing (refer to 7.5.1.5 Format Errors). The coprocessor and main processor coordinate the transfer of the internal state of the coprocessor using the operand CIR. The MC68020/EC020 completes the coprocessor context save by repeatedly reading the operand CIR and writing the 7-22 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. information obtained into memory until all the bytes specified in the coprocessor format word have been transferred. Following a cpSAVE instruction, the coprocessor should be in an idle state--that is, not executing any coprocessor instructions. Freescale Semiconductor, Inc... The cpSAVE instruction is a privileged instruction. When the MC68020/EC020 identifies a cpSAVE instruction, it checks the S-bit in the SR to determine whether it is operating at the supervisor privilege level. If the MC68020/EC020 attempts to execute a cpSAVE instruction while at the user privilege level (S-bit in the SR is clear), it initiates privilege violation exception processing without accessing any of the CIRs (refer to 7.5.2.3 Privilege Violations). The MC68020/EC020 initiates format error exception processing if it reads an invalid format word (or a valid format word whose length field is not a multiple of four bytes) from the save CIR during the execution of a cpSAVE instruction (refer to 7.2.3.2.3 Invalid Format Word). The MC68020/EC020 writes an abort mask (refer to 7.2.3.2.3 Invalid Format Word) to the control CIR to abort the coprocessor instruction prior to beginning exception processing. Figure 7-16 does not include this case since a coprocessor usually returns either a not-ready or a valid format code in the context of the cpSAVE instruction. The coprocessor can return the invalid format word, however, if a cpSAVE is initiated while the coprocessor is executing a cpSAVE or cpRESTORE instruction and the coprocessor is unable to support the suspension of these two instructions. 7.2.3.4 COPROCESSOR CONTEXT RESTORE INSTRUCTION. The M68000 coprocessor context restore instruction category includes one instruction. The coprocessor context restore instruction, denoted by the cpRESTORE mnemonic, forces a coprocessor to terminate any current operations and to restore a former state. During execution of a cpRESTORE instruction, the coprocessor can communicate status information to the main processor by placing format codes in the restore CIR. 7.2.3.4.1 Format. Figure 7-17 shows the format of the cpRESTORE instruction. 15 14 13 12 1 1 1 1 11 9 CpID 8 7 6 1 0 1 5 0 EFFECTIVE ADDRESS EFFECTIVE ADDRESS EXTENSION WORDS (0-5 WORDS) Figure 7-17. Coprocessor Context Restore Instruction Format (cpRESTORE) The first word of the instruction, the F-line operation word, contains the CpID code in bits 11-9 and an M68000 effective addressing code in bits 5-0. The effective address encoded in the cpRESTORE instruction is the starting address in memory where the coprocessor context is stored. The effective address is that of the coprocessor format word that applies to the context to be restored to the coprocessor. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-23 Freescale Semiconductor, Inc. The instruction can include as many as five effective address extension words following the F-line operation word in the cpRESTORE instruction format. These words contain any additional information required to calculate the effective address specified by bits 5-0 of the F-line operation word. Freescale Semiconductor, Inc... All memory addressing modes except the predecrement addressing mode are valid. Invalid effective address encodings cause the MC68020/EC020 to initiate F-line emulator exception processing (refer to 7.5.2.2 F-Line Emulator Exceptions). 7.2.3.4.2 Protocol. Figure 7-18 shows the protocol for the coprocessor context restore instruction. When the main processor executes a cpRESTORE instruction, it first reads the coprocessor format word from the effective address in the instruction. This format word contains a format code and a length field. During cpRESTORE operation, the main processor retains a copy of the length field to determine the number of bytes to be transferred to the coprocessor during the cpRESTORE operation and writes the format word to the restore CIR to initiate the coprocessor context restore. MAIN PROCESSOR COPROCESSOR M1 RECOGNIZE COPROCESSOR INSTRUCTION F-LINE OPERATION WORD M2 READ COPROCESSOR FORMAT CODE FROM EFFECTIVE ADDRESS SPECIFIED IN OPERATION WORD M3 WRITE COPROCESSOR FORMAT WORD TO RESTORE CIR M4 C1 TERMINATE CURRENT OPERATIONS AND EVALUATE FORMAT WORD C2 IF (INVALID FORMAT) PLACE INVALID FORMAT CODE IN THE RESTORE CIR READ RESTORE CIR M5 IF (FORMAT = INVALID FORMAT) WRITE $0001 ABORT CODE TO CONTROL CIR AND INITIATE FORMAT ERROR EXCEPTION PROCESSING (SEE NOTE 1) C3 IF (VALID FORMAT) RECEIVE NUMBER OF BYTES INDICATED IN FORMAT WORD THROUGH OPERAND CIR M6 IF (FORMAT = EMPTY/RESET) GO TO M7; ELSE, TRANSFER NUMBER OF BYTES SPECIFIED BY FORMAT WORD TO OPERAND CIR (SEE NOTE 2) M7 PROCEED WITH EXECUTION OF NEXT INSTRUCTION NOTES: 1. See 7.6.1.5 Format Error. 2. The MC68020/EC020 uses the length field in the format word read during M2 to determine the number of bytes to read from memory and write to the operand CIR. Figure 7-18. Coprocessor Context Restore Instruction Protocol When the coprocessor receives the format word in the restore CIR, it must terminate any current operations and evaluate the format word. If the format word represents a valid coprocessor context as determined by the coprocessor design, the coprocessor returns the format word to the main processor through the restore CIR and prepares to receive the number of bytes specified in the format word through its operand CIR. 7-24 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. After writing the format word to the restore CIR, the main processor continues cpRESTORE dialog by reading that same register. If the coprocessor returns a valid format word, the main processor transfers the number of bytes specified by the format word at the effective address to the operand CIR. Freescale Semiconductor, Inc... If the format word written to the restore CIR does not represent a valid coprocessor state frame, the coprocessor places an invalid format word in the restore CIR and terminates any current operations. The main processor receives the invalid format code, writes an abort mask (refer to 7.2.3.2.3 Invalid Format Word) to the control CIR, and initiates format error exception processing (refer to 7.5.1.5 Format Errors). The cpRESTORE instruction is a privileged instruction. When the MC68020/EC020 accesses a cpRESTORE instruction, it checks the S-bit in the SR. If the MC68020/EC020 attempts to execute a cpRESTORE instruction while at the user privilege level (S-bit in the SR is clear), it initiates privilege violation exception processing without accessing any of the CIRs (refer to 7.5.2.3 Privilege Violations). 7.3 COPROCESSOR INTERFACE REGISTER SET The instructions of the M68000 coprocessor interface use registers of the CIR set to communicate with the coprocessor. These CIRs are not directly related to the coprocessor programming model. Figure 7-4 is a memory map of the CIR set. The response, control, save, restore, command, condition, and operand registers must be included in a coprocessor interface that implements all four coprocessor instruction categories. The complete register model must be implemented if the system uses all coprocessor response primitives defined for the M68000 coprocessor interface. The following paragraphs contain detailed descriptions of the registers. 7.3.1 Response CIR The coprocessor uses the 16-bit response CIR to communicate all service requests (coprocessor response primitives) to the main processor. The main processor reads the response CIR to receive the coprocessor response primitives during the execution of instructions in the general and conditional instruction categories. The offset from the base address of the CIR set for the response CIR is $00. Refer to 7.4 Coprocessor Response Primitives for additional information. 7.3.2 Control CIR The main processor writes to the 2-bit control CIR to acknowledge coprocessor-requested exception processing or to abort the execution of a coprocessor instruction. The offset from the base address of the CIR set for the control CIR is $02. The control CIR occupies the two least significant bits of the word at that offset. The 14 most significant bits of the word are undefined and reserved by Motorola. Figure 7-19 shows the format of this register. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-25 Freescale Semiconductor, Inc. 15 2 (UNDEFINED, RESERVED) 1 0 XA AB Figure 7-19. Control CIR Format When the MC68020/EC020 receives one of the three take exception coprocessor response primitives, it acknowledges the primitive by setting the exception acknowledge bit (XA) in the control CIR. The MC68020/EC020 sets the abort bit (AB) in the control CIR to abort any coprocessor instruction in progress. (The 14 most significant bits of both masks are undefined.) The MC68020/EC020 aborts a coprocessor instruction when it detects one of the following exception conditions: Freescale Semiconductor, Inc... * An F-line emulator exception condition after reading a response primitive * A privilege violation exception as it performs a supervisor check in response to a supervisor check primitive * A format error exception when it receives an invalid format word or a valid format word that contains an invalid length 7.3.3 Save CIR The coprocessor uses the 16-bit save CIR to communicate status and state frame format information to the main processor while executing a cpSAVE instruction. The main processor reads the save CIR to initiate execution of the cpSAVE instruction by the coprocessor. The offset from the base address of the CIR set for the save CIR is $04. Refer to 7.2.3.2 Coprocessor Format Words for more information on the save CIR. 7.3.4 Restore CIR The main processor initiates the cpRESTORE instruction by writing a coprocessor format word to the 16-bit restore register. During the execution of the cpRESTORE instruction, the coprocessor communicates status and state frame format information to the main processor through the restore CIR. The offset from the base address of the CIR set for the restore CIR is $06. Refer to 7.2.3.2 Coprocessor Format Words for more information on the restore CIR. 7.3.5 Operation Word CIR The main processor writes the F-line operation word of the instruction in progress to the 16-bit operation word CIR in response to a transfer operation word coprocessor response primitive (refer to 7.4.6 Transfer Operation Word Primitive). The offset from the base address of the CIR set for the operation word CIR is $08. 7.3.6 Command CIR The main processor initiates a coprocessor general category instruction by writing the instruction command word, which follows the instruction F-line operation word in the instruction stream, to the 16-bit command CIR. The offset from the base address of the CIR set for the command CIR is $0A. 7-26 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 7.3.7 Condition CIR The main processor initiates a conditional category instruction by writing the condition selector to bits 5-0 of the 16-bit condition CIR. Bits 15-6 are undefined and reserved by Motorola. The offset from the base address of the CIR set for the condition CIR is $0E. Figure 7-20 shows the format of the condition CIR. 15 6 5 (UNDEFINED, RESERVED) 0 CONDITION SELECTOR Freescale Semiconductor, Inc... Figure 7-20. Condition CIR Format 7.3.8 Operand CIR When the coprocessor requests the transfer of an operand, the main processor performs the transfer by reading from or writing to the 32-bit operand CIR. The offset from the base address of the CIR set for the operand CIR is $10. The MC68020/EC020 aligns all operands transferred to and from the operand CIR to the most significant byte of this CIR. The processor performs a sequence of long-word transfers to read or write any operand larger than four bytes. If the operand size is not a multiple of four bytes, the portion remaining after the initial long-word transfer is aligned to the most significant byte of the operand CIR. Figure 7-21 shows the operand alignment used by the MC68020/EC020 when accessing the operand CIR. 31 24 23 16 15 BYTE OPERAND 8 7 0 NO TRANSFER WORD OPERAND NO TRANSFER THREE-BYTE OPERAND NO TRANSFER LONG-WORD OPERAND TENBYTEOPERAND NO TRANSFER Figure 7-21. Operand Alignment for Operand CIR Accesses MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-27 Freescale Semiconductor, Inc. 7.3.9 Register Select CIR When the coprocessor requests the transfer of one or more main processor registers or a group of coprocessor registers, the main processor reads the 16-bit register select CIR to identify the number or type of registers to be transferred. The offset from the base address of the CIR set for the register select CIR is $14. The format of this register depends on the primitive that is currently using it (refer to 7.4 Coprocessor Response Primitives). Freescale Semiconductor, Inc... 7.3.10 Instruction Address CIR When the coprocessor requests the address of the instruction it is currently executing, the main processor transfers this address to the 32-bit instruction address CIR. Any transfer of the scanPC is also performed through the instruction address CIR (refer to 7.4.17 Transfer Status Register and ScanPC Primitive). The offset from the base address of the CIR set for the instruction address CIR is $18. 7.3.11 Operand Address CIR When a coprocessor requests an operand address transfer between the main processor and the coprocessor, the address is transferred through the 32-bit operand address CIR. The offset from the base address of the CIR set for the operand address CIR is $1C. 7.4 COPROCESSOR RESPONSE PRIMITIVES The response primitives are primitive instructions that the coprocessor issues to the main processor during the execution of a coprocessor instruction. The coprocessor uses response primitives to communicate status information and service requests to the main processor. In response to an instruction command word written to the command CIR or a condition selector in the condition CIR, the coprocessor returns a response primitive in the response CIR. Within the general and conditional instruction categories, individual instructions are distinguished by the operation of the coprocessor hardware and by services specified by coprocessor response primitives and provided by the main processor. Subsequent paragraphs, beginning with 7.4.2 Coprocessor Response Primitive General Format, consist of detailed descriptions of the M68000 coprocessor response primitives supported by the MC68020/EC020. Any response primitive that the MC68020/EC020 does not recognize causes it to initiate protocol violation exception processing (refer to 7.5.2.1 Protocol Violations). This processing of undefined primitives supports emulation of extensions to the M68000 coprocessor response primitive set by the protocol violation exception handler. Exception processing related to the coprocessor interface is discussed in 7.5 Exceptions. 7-28 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 7.4.1 ScanPC Several of the response primitives involve the scanPC, and many of them require the main processor to use it while performing services requested. These paragraphs describe the scanPC and its operation. Freescale Semiconductor, Inc... During the execution of a coprocessor instruction, the PC in the MC68020/EC020 contains the address of the F-line operation word of that instruction. A second register, called the scanPC, sequentially addresses the remaining words of the instruction. If the main processor requires extension words to calculate an effective address or destination address of a branch operation, it uses the scanPC to address these extension words in the instruction stream. Also, if a coprocessor requests the transfer of extension words, the scanPC addresses the extension words during the transfer. As the processor references each word, it increments the scanPC to point to the next word in the instruction stream. When an instruction has completed, the processor transfers the value in the scanPC to the PC to address the operation word of the next instruction. The value in the scanPC when the main processor reads the first response primitive after beginning to execute an instruction depends on the instruction being executed. For a cpGEN instruction, the scanPC points to the word following the coprocessor command word. For the cpBcc instructions, the scanPC points to the word following the instruction F-line operation word. For the cpScc, cpTRAPcc, and cpDBcc instructions, the scanPC points to the word following the coprocessor condition specifier word. If a coprocessor implementation uses optional instruction extension words with a general or conditional instruction, the coprocessor must use these words consistently so that the scanPC is updated accordingly during the instruction execution. Specifically, during the execution of general category instructions, when the coprocessor terminates the instruction protocol, the MC68020/EC020 assumes that the scanPC is pointing to the operation word of the next instruction to be executed. During the execution of conditional category instructions, when the coprocessor terminates the instruction protocol, the MC68020/EC020 assumes that the scanPC is pointing to the word following the last of any coprocessor-defined extension words in the instruction format. 7.4.2 Coprocessor Response Primitive General Format The M68000 coprocessor response primitives are encoded in a 16-bit word that is transferred to the main processor through the response CIR. Figure 7-22 shows the format of the coprocessor response primitives. 15 14 13 CA PC DR 12 8 7 FUNCTION 0 PARAMETER Figure 7-22. Coprocessor Response Primitive Format MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-29 Freescale Semiconductor, Inc. The encoding of bits 12-0 of a coprocessor response primitive depends on the individual primitive. Bits 15-13, however, specify optional additional operations that apply to most of the primitives defined for the M68000 coprocessor interface. Freescale Semiconductor, Inc... The CA bit specifies the come-again operation of the main processor. When the main processor reads a response primitive from the response CIR with the CA bit set, it performs the service indicated by the primitive and then reads the response CIR again. Using the CA bit, a coprocessor can transfer several response primitives to the main processor during the execution of a single coprocessor instruction. The PC bit specifies the pass program counter operation. When the main processor reads a primitive with the PC bit set from the response CIR, the main processor immediately passes the current value in its program counter to the instruction address CIR as the first operation in servicing the primitive request. The value in the program counter is the address of the F-line operation word of the coprocessor instruction currently executing. The PC bit is implemented in all coprocessor response primitives currently defined for the M68000 coprocessor interface. When an undefined primitive or a primitive that requests an illegal operation is passed to the main processor, the main processor initiates exception processing for either an F-line emulator or a protocol violation exception (refer to 7.5.2 Main-Processor-Detected Exceptions). If the PC bit is set in one of these response primitives, however, the main processor passes the program counter to the instruction address CIR before it initiates exception processing. When the main processor initiates a cpGEN instruction that can be executed concurrently with main processor instructions, the PC bit is usually set in the first primitive returned by the coprocessor. Since the main processor proceeds with instruction stream execution once the coprocessor releases it, the coprocessor must record the instruction address to support any possible exception processing related to the instruction. Exception processing related to concurrent coprocessor instruction execution is discussed in 7.5.1 Coprocessor-Detected Exceptions. The DR bit is the direction bit. It applies to operand transfers between the main processor and the coprocessor. If the DR bit is clear, the direction of transfer is from the main processor to the coprocessor (main processor write). If the DR bit is set, the direction of transfer is from the coprocessor to the main processor (main processor read). If the operation indicated by a given response primitive does not involve an explicit operand transfer, the value of this bit depends on the particular primitive encoding. 7-30 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 7.4.3 Busy Primitive The busy response primitive causes the main processor to reinitiate a coprocessor instruction. This primitive applies to instructions in the general and conditional categories. Figure 7-23 shows the format of the busy primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 PC 1 0 0 1 0 0 0 0 0 0 0 0 0 0 Figure 7-23. Busy Primitive Format Freescale Semiconductor, Inc... The busy primitive uses the PC bit as described in 7.4.2 Coprocessor Response Primitive General Format. Coprocessors that can operate concurrently with the main processor but cannot buffer write operations to their command or condition CIR use the busy primitive. A coprocessor may execute a cpGEN instruction concurrently with an instruction in the main processor. If the main processor attempts to initiate an instruction in the general or conditional instruction category while the coprocessor is executing a cpGEN instruction, the coprocessor can place the busy primitive in the response CIR. When the main processor reads this primitive, it services pending interrupts using a preinstruction exception stack frame (refer to Figure 7-41). The processor then restarts the general or conditional coprocessor instruction that it had attempted to initiate earlier. The busy primitive should only be used in response to a write to the command or condition CIR. It should be the first primitive returned after the main processor attempts to initiate a general or conditional category instruction. In particular, the busy primitive should not be issued after program-visible resources have been altered by the instruction. (Programvisible resources include coprocessor and main processor program-visible registers and operands in memory, but not the scanPC.) The restart of an instruction after it has altered program-visible resources causes those resources to have inconsistent values when the processor reinitiates the instruction. The MC68020/EC020 responds to the busy primitive differently in a special case that can occur during a breakpoint operation (refer to Section 6 Exception Processing). This special case occurs when a breakpoint acknowledge cycle initiates a coprocessor F-line instruction, the coprocessor returns the busy primitive in response to the instruction initiation, and an interrupt is pending. When these three conditions are met, the processor reexecutes the breakpoint acknowledge cycle after completion of interrupt exception processing. A design that uses a breakpoint to monitor the number of passes through a loop by incrementing or decrementing a counter may not work correctly under these conditions. This special case may cause several breakpoint acknowledge cycles to be executed during a single pass through a loop. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-31 Freescale Semiconductor, Inc. 7.4.4 Null Primitive The null coprocessor response primitive communicates coprocessor status information to the main processor. This primitive applies to instructions in the general and conditional categories. Figure 7-24 shows the format of the null primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 1 0 0 IA 0 0 0 0 0 0 PF TF Figure 7-24. Null Primitive Format Freescale Semiconductor, Inc... The null primitive uses the CA and PC bits as described in 7.4.2 Coprocessor Response Primitive General Format. The IA bit specifies the interrupts allowed optional operation. This bit determines whether the MC68020/EC020 services pending interrupts prior to rereading the response CIR after receiving a null primitive. Interrupts are allowed when the IA bit is set. The PF bit shows the processing-finished status of the coprocessor. That is, PF = 1 indicates that the coprocessor has completed all processing associated with an instruction. The TF bit indicates the true/false condition during execution of a conditional category instruction. TF = 1 is the true condition specifier; TF = 0 is the false condition specifier. The TF bit is only relevant for null primitives with CA = 0 that are used by the coprocessor during the execution of a conditional instruction. The MC68020/EC020 processes a null primitive with CA = 1 in the same manner whether executing a general or conditional category coprocessor instruction. If the coprocessor sets CA and IA in the null primitive, the main processor services pending interrupts using a midinstruction stack frame (refer to Figure 7-43) and reads the response CIR again. If the coprocessor sets CA and clears IA in the null primitive, the main processor reads the response CIR again without servicing any pending interrupts. A null primitive with CA = 0 provides a condition evaluation indicator to the main processor during the execution of a conditional instruction and ends the dialogue between the main processor and coprocessor for that instruction. The main processor completes the execution of a conditional category coprocessor instruction when it receives the primitive. The PF bit is not relevant during conditional instruction execution since the primitive itself implies completion of processing. Usually, when the main processor reads any primitive that does not have CA = 1 while executing a general category instruction, it terminates the dialogue between the main processor and coprocessor. If a trace exception is pending, however, the main processor does not terminate the instruction dialogue until it reads a null primitive with CA = 0 and PF = 1 from the response CIR (refer to 7.5.2.5 Trace Exceptions). Thus, the main processor continues to read the response CIR until it receives a null primitive with CA = 0 7-32 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. and PF = 1, and then performs trace exception processing. When IA = 1, the main processor services pending interrupts before reading the response CIR again. Freescale Semiconductor, Inc... A coprocessor can be designed to execute a cpGEN instruction concurrently with the execution of main processor instructions and, also, buffer one write operation to either its command or condition CIR. This type of coprocessor issues a null primitive with CA = 1 when it is concurrently executing a cpGEN instruction, and the main processor initiates another general or conditional coprocessor instruction. This primitive indicates that the coprocessor is busy and the main processor should read the response CIR again without reinitiating the instruction. The IA bit of this null primitive usually should be set to minimize interrupt latency while the main processor is waiting for the coprocessor to complete the general category instruction. Table 7-3 summarizes the encodings of the null primitive. Table 7-3. Null Coprocessor Response Primitive Encodings CA PC IA PF TF General Instructions Conditional Instructions x 1 x x x Pass Program Counter to Instruction Address CIR, Clear PC Bit, and Proceed with Operation Specified by CA, IA, PF, and TF Bits Same as General Category 1 0 0 x x Reread Response CIR, Do Not Service Pending Interrupts Same as General Category 1 0 1 x x Service Pending Interrupts and Reread the Response CIR Same as General Category 0 0 0 0 c If (Trace Pending) Reread Response CIR; Else, Execute Next Instruction Main Processor Completes Instruction Execution Based on TF = c 0 0 1 0 c If (Trace Pending) Service Pending Interrupts and Reread Response CIR; Else, Execute Next Instruction Main Processor Completes Instruction Execution Based on TF = c 0 0 x 1 c Coprocessor Instruction Completed; Service Pending Exceptions or Execute Next Instruction Main Processor Completes Instruction Execution Based on TF = c. x = Don't Care c = 1 or 0 Depending on Coprocessor Condition Evaluation MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-33 Freescale Semiconductor, Inc. 7.4.5 Supervisor Check Primitive The supervisor check primitive verifies that the main processor is operating in the supervisor privilege level while executing a coprocessor instruction. This primitive applies to instructions in the general and conditional coprocessor instruction categories. Figure 7-25 shows the format of the supervisor check primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 PC 0 0 0 1 0 0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Figure 7-25. Supervisor Check Primitive Format The supervisor check primitive uses the PC bit as described in 7.4.2 Coprocessor Response Primitive General Format. Bit 15 is shown as one, but during execution of a general category instruction, this primitive performs the same operations, regardless of the value of bit 15. However, if this primitive is issued with bit 15 = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. When the MC68020/EC020 reads the supervisor check primitive from the response CIR, it checks the value of the S-bit in the SR. If S = 0 (main processor operating at user privilege level), the main processor aborts the coprocessor instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR). The main processor then initiates privilege violation exception processing (refer to 7.5.2.3 Privilege Violations). If the main processor is at the supervisor privilege level when it receives this primitive, it reads the response CIR again. The supervisor check primitive allows privileged instructions to be defined in the coprocessor general and conditional instruction categories. This primitive should be the first one issued by the coprocessor during the dialog for an instruction that is implemented as privileged. 7.4.6 Transfer Operation Word Primitive The transfer operation word primitive requests a copy of the coprocessor instruction operation word for the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-26 shows the format of the transfer operation word primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 0 1 1 1 0 0 0 0 0 0 0 0 Figure 7-26. Transfer Operation Word Primitive Format 7-34 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The transfer operation word primitive uses the CA and PC bits as described in 7.4.2 Coprocessor Response Primitive General Format. If this primitive is issued with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. When the main processor reads this primitive from the response CIR, it transfers the F-line operation word of the currently executing coprocessor instruction to the operation word CIR. The value of the scanPC is not affected by this primitive. Freescale Semiconductor, Inc... 7.4.7 Transfer from Instruction Stream Primitive The transfer from instruction stream primitive initiates transfers of operands from the instruction stream to the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-27 shows the format of the transfer from instruction stream primitive. 15 14 13 12 11 10 9 8 CA PC 0 0 1 1 1 1 7 0 LENGTH Figure 7-27. Transfer from Instruction Stream Primitive Format The transfer from instruction stream primitive uses the CA and PC bits as described in 7.4.2 Coprocessor Response Primitive General Format. If this primitive is issued with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. The length field of this primitive specifies the length, in bytes, of the operand to be transferred from the instruction stream to the coprocessor. The length must be an even number of bytes. If an odd length is specified, the main processor initiates protocol violation exception processing (refer to 7.5.2.1 Protocol Violations). This primitive transfers coprocessor-defined extension words to the coprocessor. When the main processor reads this primitive from the response CIR, it copies the number of bytes indicated by the length field from the instruction stream to the operand CIR. The first word or long word transferred is at the location pointed to by the scanPC when the primitive is read by the main processor. The scanPC is incremented after each word or long word is transferred. When execution of the primitive has completed, the scanPC has been incremented by the total number of bytes transferred and points to the word following the last word transferred. The main processor transfers the operands from the instruction stream, using a sequence of long-word writes, to the operand CIR. If the length field is not an even multiple of four bytes, the last two bytes from the instruction stream are transferred using a word write to the operand CIR. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-35 Freescale Semiconductor, Inc. 7.4.8 Evaluate and Transfer Effective Address Primitive The evaluate and transfer effective address primitive evaluates the effective address specified in the coprocessor instruction operation word and transfers the result to the coprocessor. This primitive applies to general category instructions. If this primitive is issued by the coprocessor during the execution of a conditional category instruction, the main processor initiates protocol violation exception processing. Figure 7-28 shows the format of the evaluate and transfer effective address primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 1 0 1 0 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Figure 7-28. Evaluate and Transfer Effective Address Primitive Format The evaluate and transfer effective address primitive uses the CA and PC bits as described in 7.4.2 Coprocessor Response Primitive General Format. When the main processor reads this primitive while executing a general category instruction, it evaluates the effective address specified in the instruction. At this point, the scanPC contains the address of the first of any required effective address extension words. The main processor increments the scanPC by two after it references each of these extension words. After the effective address is calculated, the resulting 32-bit value is written to the operand address CIR. The MC68020/EC020 only calculates effective addresses for control alterable addressing modes in response to this primitive. If the addressing mode in the operation word is not a control alterable mode, the main processor aborts the instruction by writing a $0001 to the control CIR and initiates F-line emulation exception processing (refer to 7.5.2.2 F-Line Emulator Exceptions). 7.4.9 Evaluate Effective Address and Transfer Data Primitive The evaluate effective address and transfer data primitive transfers an operand between the coprocessor and the effective address specified in the coprocessor instruction operation word. This primitive applies to general category instructions. If the coprocessor issues this primitive during the execution of a conditional category instruction, the main processor initiates protocol violation exception processing. Figure 7-29 shows the format of the evaluate effective address and transfer data primitive. 15 14 13 12 11 CA PC DR 1 0 10 9 8 7 VALID EA 0 LENGTH Figure 7-29. Evaluate Effective Address and Transfer Data Primitive Format This primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. 7-36 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The valid EA field of the primitive format specifies the valid effective address categories for this primitive. If the effective address specified in the instruction operation word is not a member of the class specified by the valid EA field, the main processor aborts the coprocessor instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR) and by initiating F-line emulation exception processing. Table 7-4 lists the valid effective address field encodings. Table 7-4. Valid Effective Address Field Codes Freescale Semiconductor, Inc... Field Category 000 Control Alterable 001 Data Alterable 010 Memory Alterable 011 Alterable 100 Control 101 Data 110 Memory 111 Any Effective Address (No Restriction) Even when the valid EA fields specified in the primitive and in the instruction operation word match, the MC68020/EC020 initiates protocol violation exception processing if the primitive requests a write to an unalterable effective address. The length in bytes of the operand to be transferred is specified by the length field of the primitive format. Several restrictions apply to operand lengths for certain effective addressing modes. If the effective address is a main processor register (register direct mode), only operand lengths of one, two, or four bytes are valid; all other lengths cause the main processor to initiate protocol violation exception processing. Operand lengths of 0-255 bytes are valid for the memory addressing modes. The length of 0-255 bytes does not apply to an immediate operand. The length of an immediate operand must be one byte or an even number of bytes (less than 256), and the direction of transfer must be to the coprocessor; otherwise, the main processor initiates protocol violation exception processing. When the main processor receives the evaluate effective address and transfer data primitive during the execution of a general category instruction, it verifies that the effective address encoded in the instruction operation word is in the category specified by the primitive. If so, the processor calculates the effective address using the appropriate effective address extension words at the current scanPC address and increments the scanPC by two for each word referenced. Using long-word transfers whenever possible, the main processor then transfers the number of bytes specified in the primitive between the operand CIR and the effective address. Refer to 7.3.8 Operand CIR for information concerning operand alignment for transfers involving the operand CIR. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-37 Freescale Semiconductor, Inc. The DR bit specifies the direction of the operand transfer. DR = 0 requests a transfer from the main processor to the coprocessor, and DR = 1 specifies a transfer from the coprocessor to the main processor. Freescale Semiconductor, Inc... If the effective addressing mode specifies the predecrement mode, the address register used is decremented by the size of the operand before the transfer. The bytes within the operand are then transferred to or from ascending addresses beginning with the location specified by the decremented address register. In this mode, if A7 is used as the address register and the operand length is one byte, A7 is decremented by two to maintain a wordaligned stack. For the postincrement effective addressing mode, the address register used is incremented by the size of the operand after the transfer. The bytes within the operand are transferred to or from ascending addresses beginning with the location specified by the address register. In this mode, if A7 is used as the address register and the operand length is one byte, A7 is incremented by two after the transfer to maintain a word-aligned stack. Transferring odd length operands longer than one byte using the -(A7) or (A7)+ addressing modes can result in a stack pointer that is not word aligned. The processor repeats the effective address calculation each time this primitive is issued during the execution of a given instruction. The calculation uses the current contents of any required address and data registers. The instruction must include a set of effective address extension words for each repetition of a calculation that requires them. The processor locates these words at the current scanPC location and increments the scanPC by two for each word referenced in the instruction stream. The MC68020/EC020 sign-extends a byte or word-sized operand to a long-word value when it is transferred to an address register (A7-A0) using this primitive with the register direct effective addressing mode. A byte or word-sized operand transferred to a data register (D7-D0) only overwrites the lower byte or word of the data register. 7.4.10 Write to Previously Evaluated Effective Address Primitive The write to previously evaluated effective address primitive transfers an operand from the coprocessor to a previously evaluated effective address. This primitive applies to general category instructions. If the coprocessor uses this primitive during the execution of a conditional category instruction, the main processor initiates protocol violation exception processing. Figure 7-30 shows the format of the write to previously evaluated effective address primitive. 15 14 13 12 11 10 9 8 CA PC 1 0 0 0 0 0 7 0 LENGTH Figure 7-30. Write to Previously Evaluated Effective Address Primitive Format 7-38 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The write to previously evaluated effective address primitive uses the CA and PC bits as described in 7.4.2 Coprocessor Response Primitive General Format. Freescale Semiconductor, Inc... The length field of the primitive format specifies the length of the operand in bytes. The MC68020/EC020 transfers operands of 0-255 bytes in length. When the main processor receives this primitive during the execution of a general category instruction, it transfers an operand from the operand CIR to an effective address specified by a temporary register within the MC68020/EC020. When a previous primitive for the current instruction has evaluated the effective address, this temporary register contains the evaluated effective address. Primitives that store an evaluated effective address in a temporary register of the main processor are the evaluate and transfer effective address, evaluate effective address and transfer data, and transfer multiple coprocessor registers primitive. If this primitive is used during an instruction in which the effective address specified in the instruction operation word has not been calculated, the effective address used for the write is undefined. Also, if the previously evaluated effective address was register direct, the address written to in response to this primitive is undefined. The function code value during the write operation indicates either supervisor or user data space, depending on the value of the S-bit in the MC68020/EC020 SR when the processor reads this primitive. While a coprocessor should request writes to only alterable effective addressing modes, the MC68020/EC020 does not check the type of effective address used with this primitive. For example, if the previously evaluated effective address was PC relative and the MC68020/EC020 is at the user privilege level (S = 0 in SR), the MC68020/EC020 writes to user data space at the previously calculated program relative address (the 32-bit value in the temporary internal register of the processor). Operands longer than four bytes are transferred in increments of four bytes (operand parts) when possible. The main processor reads a long-word operand part from the operand CIR and transfers this part to the current effective address. The transfers continue in this manner using ascending memory locations until all of the long-word operand parts are transferred, and any remaining operand part is then transferred using a one-, two-, or three-byte transfer as required. The operand parts are stored in memory using ascending addresses beginning with the address in the MC68020/EC020 temporary register, which is internal to the processor and not for user use. The execution of this primitive does not modify any of the registers in the MC68020/EC020 programming model, even if the previously evaluated effective address mode is the predecrement or postincrement mode. If the previously evaluated effective addressing mode used any of the MC68020/EC020 internal address or data registers, the effective address value used is the final value from the preceding primitive. That is, this primitive uses the value from an evaluate and transfer effective address, evaluate effective address and transfer data, or transfer multiple coprocessor registers primitive without modification. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-39 Freescale Semiconductor, Inc. The take address and transfer data primitive described in 7.4.11 Take Address and Transfer Data Primitive does not replace the effective address value that has been calculated by the MC68020/EC020. The address that the main processor obtains in response to the take address and transfer data primitive is not available to the write to previously evaluated effective address primitive. A coprocessor can issue an evaluate effective address and transfer data primitive followed by this primitive to perform a read-modify-write operation that is not indivisible. The bus cycles for this operation are normal bus cycles that can be interrupted, and the bus can be arbitrated between the cycles. Freescale Semiconductor, Inc... 7.4.11 Take Address and Transfer Data Primitive The take address and transfer data primitive transfers an operand between the coprocessor and an address supplied by the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-31 shows the format of the take address and transfer data primitive. 15 14 13 12 11 10 9 8 CA PC DR 0 0 1 0 1 7 0 LENGTH Figure 7-31. Take Address and Transfer Data Primitive Format The take address and transfer data primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. If the coprocessor issues this primitive with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. The length field of the primitive format specifies the operand length, which can be from 0-255 bytes. The main processor reads a 32-bit address from the operand address CIR. Using a series of long-word transfers, the processor transfers the operand between this address and the operand CIR. The DR bit determines the direction of the transfer. The processor reads or writes the operand parts to ascending addresses, starting at the address from the operand address CIR. If the operand length is not a multiple of four bytes, the final operand part is transferred using a one-, two-, or three-byte transfer as required. The function code used with the address read from the operand address CIR indicates either supervisor or user data space according to the value of the S-bit in the MC68020/EC020 SR. 7-40 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 7.4.12 Transfer to/from Top of Stack Primitive The transfer to/from top of stack primitive transfers an operand between the coprocessor and the top of the active system stack of the main processor. This primitive applies to general and conditional category instructions. Figure 7-32 shows the format of the transfer to/from top of stack primitive. 15 14 13 12 11 10 9 8 CA PC DR 0 1 1 1 0 7 0 LENGTH Freescale Semiconductor, Inc... Figure 7-32. Transfer to/from Top of Stack Primitive Format The transfer to/from top of stack primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. If the coprocessor issues this primitive with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. The length field of the primitive format specifies the length in bytes of the operand to be transferred. The operand may be one, two, or four bytes in length; other length values cause the main processor to initiate protocol violation exception processing. If DR = 0, the main processor transfers the operand from the active system stack to the operand CIR. The implied effective address mode used for the transfer is the (A7)+ addressing mode. A one-byte operand causes the stack pointer to be incremented by two after the transfer to maintain word alignment of the stack. If DR = 1, the main processor transfers the operand from the operand CIR to the active system stack. The implied effective address mode used for the transfer is the -(A7) addressing mode. A one-byte operand causes the stack pointer to be decremented by two before the transfer to maintain word alignment of the stack. 7.4.13 Transfer Single Main Processor Register Primitive The transfer single main processor register primitive transfers an operand between one of the main processor's data or address registers and the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-33 shows the format of the transfer single main processor register primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 CA PC DR 0 1 1 0 0 0 0 0 0 D/A 2 0 REGISTER Figure 7-33. Transfer Single Main Processor Register Primitive Format The transfer single main processor register primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. If the coprocessor issues this primitive with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-41 Freescale Semiconductor, Inc. The D/A bit specifies whether the primitive transfers an address or data register. D/A = 0 indicates a data register, and D/A = 1 indicates an address register. The register field contains the register number. If DR = 0, the main processor writes the long-word operand in the specified register to the operand CIR. If DR = 1, the main processor reads a long-word operand from the operand CIR and transfers it to the specified data or address register. Freescale Semiconductor, Inc... 7.4.14 Transfer Main Processor Control Register Primitive The transfer main processor control register primitive transfers a long-word operand between one of its control registers and the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-34 shows the format of the transfer main processor control register primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 1 1 0 1 0 0 0 0 0 0 0 0 Figure 7-34. Transfer Main Processor Control Register Primitive Format The transfer main processor control register primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. If the coprocessor issues this primitive with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. When the main processor receives this primitive, it reads a control register select code from the register select CIR. This code determines which main processor control register is transferred. Table 7-5 lists the valid control register select codes. If the control register select code is not valid, the MC68020/EC020 initiates protocol violation exception processing (refer to 7.5.2.1 Protocol Violations). Table 7-5. Main Processor Control Register Select Codes Select Code Control Register $x000 SFC $x001 DFC $x002 CACR $x800 USP $x801 VBR $x802 CAAR $x803 MSP $x804 ISP All other codes cause a protocol violation exception. 7-42 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. After reading a valid code from the register select CIR, if DR = 0, the main processor writes the long-word operand from the specified control register to the operand CIR. If DR = 1, the main processor reads a long-word operand from the operand CIR and places it in the specified control register. 7.4.15 Transfer Multiple Main Processor Registers Primitive Freescale Semiconductor, Inc... The transfer multiple main processor registers primitive transfers long-word operands between one or more of its data or address registers and the coprocessor. This primitive applies to general and conditional category instructions. Figure 7-35 shows the format of the transfer multiple main processor registers primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 0 1 1 0 0 0 0 0 0 0 0 0 Figure 7-35. Transfer Multiple Main Processor Registers Primitive Format The transfer multiple main processor registers primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. If the coprocessor issues this primitive with CA = 0 during a conditional category instruction, the main processor initiates protocol violation exception processing. When the main processor receives this primitive, it reads a 16-bit register select mask from the register select CIR. The format of the register select mask is shown in Figure 7-36. A register is transferred if the bit corresponding to the register in the register select mask is set. The selected registers are transferred in the order D7-D0 and then A7-A0. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 Figure 7-36. Register Select Mask Format If DR = 0, the main processor writes the contents of each register indicated in the register select mask to the operand CIR using a sequence of long-word transfers. If DR = 1, the main processor reads a long-word operand from the operand CIR into each register indicated in the register select mask. The registers are transferred in the same order, regardless of the direction of transfer indicated by the DR bit. 7.4.16 Transfer Multiple Coprocessor Registers Primitive The transfer multiple coprocessor registers primitive transfers from 0-16 operands between the effective address specified in the coprocessor instruction and the coprocessor. This primitive applies to general category instructions. If the coprocessor issues this primitive during the execution of a conditional category instruction, the main processor initiates protocol violation exception processing. Figure 7-37 shows the format of the transfer multiple coprocessor registers primitive. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-43 Freescale Semiconductor, Inc. 15 14 13 12 11 10 9 8 CA PC DR 0 0 0 0 1 7 0 LENGTH Figure 7-37. Transfer Multiple Coprocessor Registers Primitive Format The transfer multiple coprocessor registers primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. Freescale Semiconductor, Inc... The length field of the primitive format indicates the length in bytes of each operand transferred. The operand length must be an even number of bytes; odd length operands cause the MC68020/EC020 to initiate protocol violation exception processing (refer to 7.5.2.1 Protocol Violations). When the main processor reads this primitive, it calculates the effective address specified in the coprocessor instruction. The scanPC should be pointing to the first of any necessary effective address extension words when this primitive is read from the response CIR; the scanPC is incremented by two for each extension word referenced during the effective address calculation. For transfers from the effective address to the coprocessor (DR = 0), the control addressing modes and the postincrement addressing mode are valid. For transfers from the coprocessor to the effective address (DR = 1), the control alterable and predecrement addressing modes are valid. Invalid addressing modes cause the MC68020/EC020 to abort the instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR) and to initiate F-line emulator exception processing (refer to 7.5.2.2 F-Line Emulator Exceptions). After performing the effective address calculation, the MC68020/EC020 reads a 16-bit register select mask from the register select CIR. The coprocessor uses the register select mask to specify the number of operands to transfer; the MC68020/EC020 counts the number of ones in the register select mask to determine the number of operands. The order of the ones in the register select mask is not relevant to the operation of the main processor. As many as 16 operands can be transferred by the main processor in response to this primitive. The total number of bytes transferred is the product of the number of operands transferred and the length of each operand specified in the length field of the primitive format. If DR = 1, the main processor reads the number of operands specified in the register select mask from the operand CIR and writes these operands to the effective address specified in the instruction using long-word transfers whenever possible. If DR = 0, the main processor reads the number of operands specified in the register select mask from the effective address and writes them to the operand CIR. For the control addressing modes, the operands are transferred to or from memory using ascending addresses. For the postincrement addressing mode, the operands are read from memory with ascending addresses also, and the address register used is incremented by the size of an operand after each operand is transferred. The address register used with the (An)+ addressing mode is incremented by the total number of bytes transferred during the primitive execution. 7-44 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. For the predecrement addressing mode, the operands are written to memory with descending addresses, but the bytes within each operand are written to memory with ascending addresses. As an example, Figure 7-38 shows the format in long-wordoriented memory for two 12-byte operands transferred from the coprocessor to the effective address using the -(An) addressing mode. The processor decrements the address register by the size of an operand before the operand is transferred. It writes the bytes of the operand to ascending memory addresses. When the transfer is complete, the address register has been decremented by the total number of bytes transferred. The MC68020/EC020 transfers the data using long-word transfers whenever possible. Freescale Semiconductor, Inc... 31 24 23 An - 2 *LENGTH = FINAL An OP1, BYTE (0) An - LENGTH OP0, BYTE (0) 16 15 8 7 0 OP1, BYTE (L - 1) OP0, BYTE (L - 1) INITIAL An NOTE: OP0, Byte (0) is the first byte written to memory OP0, Byte (L-1) is the last byte of the first operand written to memory OP1, Byte (0) is the first byte of the second operand written to memory OP1, Byte (L-1) is the last byte written to memory Figure 7-38. Operand Format in Memory for Transfer to -(An) 7.4.17 Transfer Status Register and ScanPC Primitive The transfer status register and the scanPC primitive transfers values between the coprocessor and the MC68020/EC020 SR. On an optional basis, the scanPC also makes transfers. This primitive applies to general category instructions. If the coprocessor issues this primitive during the execution of a conditional category instruction, the main processor initiates protocol violation exception processing. Figure 7-39 shows the format of the transfer status register and scanPC primitive. 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 0 0 1 SP 0 0 0 0 0 0 0 0 Figure 7-39. Transfer Status Register and ScanPC Primitive Format The transfer status register and scanPC primitive uses the CA, PC, and DR bits as described in 7.4.2 Coprocessor Response Primitive General Format. The SP bit selects the scanPC option. If SP = 1, the primitive transfers both the scanPC and SR. If SP = 0, only the SR is transferred. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-45 Freescale Semiconductor, Inc. If SP = 0 and DR = 0, the main processor writes the 16-bit SR value to the operand CIR. If SP = 0 and DR = 1, the main processor reads a 16-bit value from the operand CIR into the main processor SR. Freescale Semiconductor, Inc... If SP = 1 and DR = 0, the main processor writes the long-word value in the scanPC to the instruction address CIR and then writes the SR value to the operand CIR. If SP = 1 and DR = 1, the main processor reads a 16-bit value from the operand CIR into the SR and then reads a long-word value from the instruction address CIR into the scanPC. With this primitive, a general category instruction can change the main processor program flow by placing a new value in the SR, in the scanPC, or new values in both the SR and the scanPC. By accessing the SR, the coprocessor can determine and manipulate the main processor condition codes, supervisor status, trace modes, selection of the active stack, and interrupt mask level. The MC68020/EC020 discards any instruction words that have been prefetched beyond the current scanPC location when this primitive is issued with DR = 1 (transfer to main processor). The MC68020/EC020 then refills the instruction pipe from the scanPC address in the address space indicated by the S-bit of the SR. If the MC68020/EC020 is operating in the trace on change of flow mode (T1, T0 in the SR = 01) when the coprocessor instruction begins to execute and if this primitive is issued with DR = 1 (from coprocessor to main processor), the MC68020/EC020 prepares to take a trace exception. The trace exception occurs when the coprocessor signals that it has completed all processing associated with the instruction. Changes in the trace modes due to the transfer of the SR to the main processor take effect on execution of the next instruction. 7.4.18 Take Preinstruction Exception Primitive The take preinstruction exception primitive initiates exception processing using a coprocessor-supplied exception vector number and the preinstruction exception stack frame format. This primitive applies to general and conditional category instructions. Figure 7-40 shows the format of the take preinstruction exception primitive. 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 0 0 7 0 VECTOR NUMBER Figure 7-40. Take Preinstruction Exception Primitive Format The take preinstruction exception primitive uses the PC bit as described in 7.4.2 Coprocessor Response Primitive General Format. The vector number field contains the exception vector number used by the main processor to initiate exception processing. When the main processor receives this primitive, it acknowledges the coprocessor exception request by writing an exception acknowledge mask to the control CIR (refer to 7.3.2 Control CIR). The MC68020/EC020 then proceeds with exception processing as 7-46 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. described in Section 6 Exception Processing. The vector number for the exception is taken from the vector number field of the primitive, and the MC68020/EC020 uses the four-word stack frame format shown in Figure 7-41. 15 12 SP 11 0 STATUS REGISTER +02 PROGRAM COUNTER +06 0 0 0 0 VECTOR NUMBER Freescale Semiconductor, Inc... Figure 7-41. MC68020/EC020 Preinstruction Stack Frame The value of the PC saved in this stack frame is the F-line operation word address of the coprocessor instruction during which the primitive was received. Thus, if the exception handler routine does not modify the stack frame, an RTE instruction causes the MC68020/EC020 to return and reinitiate execution of the coprocessor instruction. The take preinstruction exception primitive can be used when the coprocessor does not recognize a value written to either its command CIR or condition CIR to initiate a coprocessor instruction. This primitive can also be used if an exception occurs in the coprocessor instruction before any program-visible resources are modified by the instruction operation. This primitive should not be used during a coprocessor instruction if program-visible resources have been modified by that instruction. Otherwise, since the MC68020/EC020 reinitiates the instruction when it returns from exception processing, the restarted instruction receives the previously modified resources in an inconsistent state. One of the most important uses of the take preinstruction exception primitive is to signal an exception condition in a cpGEN instruction that was executing concurrently with the main processor's instruction execution. If the coprocessor no longer requires the services of the main processor to complete a cpGEN instruction and if the concurrent instruction completion is transparent to the programming model, the coprocessor can release the main processor by issuing a primitive with CA = 0. The main processor usually executes the next instruction in the instruction stream, and the coprocessor completes its operations concurrently with the main processor operation. If an exception occurs while the coprocessor is executing an instruction concurrently, the exception is not processed until the main processor attempts to initiate the next general or conditional instruction. After the main processor writes to the command or condition CIR to initiate a general or conditional instruction, it then reads the response CIR. At this time, the coprocessor can return the take preinstruction exception primitive. This protocol allows the main processor to proceed with exception processing related to the previous concurrently executing coprocessor instruction and then return and reinitiate the coprocessor instruction during which the exception was signaled. The coprocessor should record the addresses of all general category instructions that can be executed concurrently with the main processor and that support exception recovery. Since the exception is not reported until the next coprocessor instruction is initiated, the processor usually requires the instruction address to determine MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-47 Freescale Semiconductor, Inc. which instruction the coprocessor was executing when the exception occurred. A coprocessor can record the instruction address by setting PC = 1 in one of the primitives it uses before releasing the main processor. 7.4.19 Take Midinstruction Exception Primitive Freescale Semiconductor, Inc... The take midinstruction exception primitive initiates exception processing using a coprocessor-supplied exception vector number and the midinstruction exception stack frame format. This primitive applies to general and conditional category instructions. Figure 7-42 shows the format of the take midinstruction exception primitive. 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 0 1 7 0 VECTOR NUMBER Figure 7-42. Take Midinstruction Exception Primitive Format The take midinstruction exception primitive uses the PC bit as described in 7.4.2 Coprocessor Response Primitive General Format. The vector number field contains the exception vector number used by the main processor to initiate exception processing. When the main processor receives this primitive, it acknowledges the coprocessor exception request by writing an exception acknowledge mask (refer to 7.3.2 Control CIR) to the control CIR. The MC68020/EC020 then performs exception processing as described in Section 6 Exception Processing. The vector number for the exception is taken from the vector number field of the primitive, and the MC68020/EC020 uses the 10-word stack frame format shown in Figure 7-43. 15 12 SP 11 0 STATUS REGISTER +02 SCAN PC +06 1 0 0 1 VECTOR NUMBER +08 PROGRAM COUNTER +0C INTERNAL REGISTER +0E OPERATION WORD +10 EFFECTIVE ADDRESS Figure 7-43. MC68020/EC020 Midinstruction Stack Frame 7-48 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. The PC value saved in this stack frame is the operation word address of the coprocessor instruction during which the primitive is received. The scanPC field contains the value of the MC68020/EC020 scanPC when the primitive is received. If the current instruction does not evaluate an effective address prior to the exception request primitive, the value of the effective address field in the stack frame is undefined. Freescale Semiconductor, Inc... The coprocessor uses this primitive to request exception processing for an exception during the instruction dialog with the main processor. If the exception handler does not modify the stack frame, the MC68020/EC020 returns from the exception handler and reads the response CIR. Thus, the main processor attempts to continue executing the suspended instruction by reading the response CIR and processing the primitive it receives. 7.4.20 Take Postinstruction Exception Primitive The take postinstruction exception primitive initiates exception processing using a coprocessor-supplied exception vector number and the postinstruction exception stack frame format. This primitive applies to general and conditional category instructions. Figure 7-44 shows the format of the take postinstruction exception primitive. 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 1 0 7 0 VECTOR NUMBER Figure 7-44. Take Postinstruction Exception Primitive Format The take postinstruction exception primitive uses the PC bit as described in 7.4.2 Coprocessor Response Primitive General Format. The vector number field contains the exception vector number used by the main processor to initiate exception processing. When the main processor receives this primitive, it acknowledges the coprocessor exception request by writing an exception acknowledge mask to the control CIR (refer to 7.3.2 Control CIR). The MC68020/EC020 then performs exception processing as described in Section 6 Exception Processing. The vector number for the exception is taken from the vector number field of the primitive, and the MC68020/EC020 uses the sixword stack frame format shown in Figure 7-45. 15 12 SP 11 0 STATUS REGISTER +02 SCAN PC +06 0 0 1 0 VECTOR NUMBER +08 PROGRAM COUNTER Figure 7-45. MC68020/EC020 Postinstruction Stack Frame MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-49 Freescale Semiconductor, Inc. The value in the main processor scanPC at the time this primitive is received is saved in the scanPC field of the postinstruction exception stack frame. The value of the PC saved is the F-line operation word address of the coprocessor instruction during which the primitive is received. Freescale Semiconductor, Inc... When the MC68020/EC020 receives the take postinstruction exception primitive, it assumes that the coprocessor either completed or aborted the instruction with an exception. If the exception handler does not modify the stack frame, the MC68020/EC020 returns from the exception handler to begin execution at the location specified by the scanPC field of the stack frame. This location should be the address of the next instruction to be executed. The coprocessor uses this primitive to request exception processing when it completes or aborts an instruction while the main processor is awaiting a normal response. For a general category instruction, the response is a release; for a conditional category instruction, it is an evaluated true/false condition indicator. Thus, the operation of the MC68020/EC020 in response to this primitive is compatible with standard M68000 family instruction related exception processing (for example, the divide-by-zero exception). 7.5 EXCEPTIONS Various exception conditions related to the execution of coprocessor instructions may occur. Whether an exception is detected by the main processor or by the coprocessor, the main processor coordinates and performs exception processing. Servicing these coprocessor-related exceptions is an extension of the protocol used to service standard M68000 family exceptions. That is, when either the main processor detects an exception or is signaled by the coprocessor that an exception condition has occurred, the main processor proceeds with exception processing as described in Section 6 Exception Processing. 7.5.1 Coprocessor-Detected Exceptions Coprocessor interface exceptions that the coprocessor detects, as well as those that the main processor detects, are usually classified as coprocessor-detected exceptions. Coprocessor-detected exceptions can occur during M68000 coprocessor interface operations, internal operations, or other system-related operations of the coprocessor. Most coprocessor-detected exceptions are signaled to the main processor through the use of one of the three take exception primitives defined for the M68000 coprocessor interface. The main processor responds to these primitives as described in 7.4.18 Take Preinstruction Exception Primitive, 7.4.19 Take Midinstruction Exception Primitive, and 7.4.20 Take Postinstruction Exception Primitive. However, not all coprocessordetected exceptions are signaled by response primitives. Coprocessor-detected format errors during the cpSAVE or cpRESTORE instruction are signaled to the main processor using the invalid format word described in 7.2.3.2.3 Invalid Format Words. 7-50 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... 7.5.1.1 COPROCESSOR-DETECTED PROTOCOL VIOLATIONS. Protocol violation exceptions are communication failures between the main processor and coprocessor across the M68000 coprocessor interface. Coprocessor-detected protocol violations occur when the main processor accesses entries in the CIR set in an unexpected sequence. The sequence of operations that the main processor performs for a given coprocessor instruction or coprocessor response primitive has been described previously in this section. A coprocessor can detect protocol violations in various ways. According to the M68000 coprocessor interface protocol, the main processor always accesses the operation word, operand, register select, instruction address, or operand address CIRs synchronously with respect to the operation of the coprocessor. That is, the main processor accesses these five registers in a certain sequence, and the coprocessor expects them to be accessed in that sequence. As a minimum, all M68000 coprocessors should detect a protocol violation if the main processor accesses any of these five registers when the coprocessor is expecting an access to either the command or condition CIR. Likewise, if the coprocessor is expecting an access to the command or condition CIR and the main processor accesses one of these five registers, the coprocessor should detect and signal a protocol violation. According to the M68000 coprocessor interface protocol, the main processor can perform a read of either the save CIR or response CIR or a write of either the restore CIR or control CIR asynchronously with respect to the operation of the coprocessor. That is, an access to one of these registers without the coprocessor explicitly expecting that access at that point can be a valid access. Although the coprocessor can anticipate certain accesses to the restore, response, and control CIRs, these registers can be accessed at other times also. The coprocessor cannot signal a protocol violation to the main processor during execution of a cpSAVE or cpRESTORE instruction. If a coprocessor detects a protocol violation during execution of the cpSAVE or cpRESTORE instruction, it should signal the exception to the main processor when the next coprocessor instruction is initiated. The main philosophy of the coprocessor-detected protocol violation is that the coprocessor should always acknowledge an access to one of its interface registers. If the coprocessor determines that the access is not valid, it should assert DSACK1/DSACK0 to the main processor and signal a protocol violation when the main processor next reads the response CIR. If the coprocessor fails to assert DSACK1 / DSACK0 , the main processor waits for the assertion of that signal (or some other bus termination signal) indefinitely. The protocol previously described ensures that the coprocessor cannot halt the main processor. The coprocessor can signal a protocol violation to the main processor with the take midinstruction exception primitive. To maintain consistency, the vector number should be 13, as it is for a protocol violation detected by the main processor. When the main processor reads this primitive, it proceeds as described in 7.4.19 Take Midinstruction Exception Primitive. If the exception handler does not modify the stack frame, the MC68020/EC020 returns from the exception handler and reads the response CIR. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-51 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... 7.5.1.2 COPROCESSOR-DETECTED ILLEGAL COMMAND OR CONDITION WORDS. Illegal coprocessor command or condition words are values written to the command CIR or condition CIR that the coprocessor does not recognize. If a value written to either of these registers is not valid, the coprocessor should return the take preinstruction exception primitive in the response CIR. When it receives this primitive, the main processor takes a preinstruction exception as described in 7.4.18 Take Preinstruction Exception Primitive. If the exception handler does not modify the main processor stack frame, an RTE instruction causes the MC68020/EC020 to reinitiate the instruction that took the exception. The coprocessor designer should ensure that the state of the coprocessor is not irrecoverably altered by an illegal command or condition exception if the system supports emulation of the unrecognized command or condition word. All M68000 coprocessors signal illegal command and condition words by returning the take preinstruction exception primitive with the F-line emulator exception vector number 11. 7.5.1.3 COPROCESSOR DATA-PROCESSING-RELATED EXCEPTIONS. Exceptions related to the internal operation of a coprocessor are classified as data-processing-related exceptions. These exceptions are analogous to the divide-by-zero exception defined by M68000 microprocessors and should be signaled to the main processor using one of the three take exception primitives containing an appropriate exception vector number. Which of these three primitives is used to signal the exception is usually determined by the point in the instruction operation where the main processor should continue the program flow after exception processing. Refer to 7.4.18 Take Preinstruction Exception Primitives, 7.4.19 Take Midinstruction Exception Primitive, and 7.4.20 Take Postinstruction Exception Primitive. 7.5.1.4 COPROCESSOR SYSTEM-RELATED EXCEPTIONS. System-related exceptions detected by a DMA coprocessor include those associated with bus activity and any other exceptions (interrupts, for example) occurring external to the coprocessor. The actions taken by the coprocessor and the main processor depend on the type of exception that occurs. When an address or bus error is detected by a DMA coprocessor, the coprocessor should store any information necessary for the main processor exception handling routines in system-accessible registers. The coprocessor should place one of the three take exception primitives encoded with an appropriate exception vector number in the response CIR. Which of the three primitives is used depends upon the point in the coprocessor instruction at which the exception was detected and the point in the instruction execution at which the main processor should continue after exception processing. Refer to 7.4.18 Take Preinstruction Exception Primitives, 7.4.19 Take Midinstruction Exception Primitive, and 7.4.20 Take Postinstruction Exception Primitive. 7-52 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. 7.5.1.5 FORMAT ERRORS. Format errors are the only coprocessor-detected exceptions that are not signaled to the main processor with a response primitive. When the main processor writes a format word to the restore CIR during the execution of a cpRESTORE instruction, the coprocessor decodes this word to determine if it is valid (refer to 7.2.3.3 Coprocessor Context Save Instruction). If the format word is not valid, the coprocessor places the invalid format code in the restore CIR. When the main processor reads the invalid format code, it aborts the coprocessor instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR). The main processor then performs exception processing using a four-word preinstruction stack frame and the format error exception vector number 14. Thus, if the exception handler does not modify the stack frame, the MC68020/EC020 restarts the cpRESTORE instruction when the RTE instruction in the handler is executed. If the coprocessor returns the invalid format code when the main processor reads the save CIR to initiate a cpSAVE instruction, the main processor performs format error exception processing as outlined for the cpRESTORE instruction. 7.5.2 Main-Processor-Detected Exceptions A number of exceptions related to coprocessor instruction execution are detected and serviced by the main processor instead of the coprocessor. These exceptions can be related to the execution of coprocessor response primitives, communication across the M68000 coprocessor interface, or completion of conditional coprocessor instructions by the main processor. 7.5.2.1 PROTOCOL VIOLATIONS. The main processor detects a protocol violation when it reads a primitive from the response CIR that is not a valid primitive. The protocol violations that can occur in response to the primitives defined for the M68000 coprocessor interface are summarized in Table 7-6. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-53 Freescale Semiconductor, Inc. Table 7-6. Exceptions Related to Primitive Processing Primitive Protocol F-Line Other Busy Null Supervisory Check * Other: Privilege Violation if S-Bit in the SR = 0 X Transfer Operation Word * Transfer from Instruction Stream* Protocol: If Length Field Is Odd (Zero Length Legal) Freescale Semiconductor, Inc... Evaluate and Transfer Effective Address Protocol: If Used with Conditional Instruction F-Line: If EA in Opword I s NOT Control Alterable Evaluate Effective Address and Transfer Data Protocol: 1. If Used with Conditional Instructions 2. Length I s Not 1, 2, or 4 and EA = Register Direct 3. If EA = Immediate and Length Odd and Greater Than 1 4. Attempt to Write to Unalterable Address Even if Address Declared Legal in Primitive F-Line: Valid EA Field Does Not Match EA in Opword Write to Previously Evaluated Effective Address Protocol: If Used with Conditional Instruction X X X X X X Take Address and Transfer Data * Transfer to/from Top of Stack* Protocol: Length Field Other Than 1, 2, or 4 X Transfer Single Main Processor Register* Transfer Main Processor Control Register Protocol: Invalid Control Register Select Code X Transfer Multiple Main Processor Registers* Transfer Multiple Coprocessor Registers Protocol: 1. If Used with Conditional Instructions 2. Odd Length Value F-Line: 1. EA Not Control Alterable or (An)+ for CP to Memory Transfer 2. EA Not Control Alterable or -(An) for Memory to CP Transfer Transfer Status and ScanPC Protocol: If Used with Conditional Instruction Other: 1. Trace--Trace Made Pending if MC68020/EC020 in "Trace on Change of Flow" Mode and DR = 1 2. Address Error--If Odd Value Written to ScanPC Take Preinstruction, Midinstruction, or Postinstruction Exception Exception Depends on Vector Supplies in Primitive X X X X X X X *Use of this primitive with CA = 0 will cause protocol violation on conditional instructions. Abbreviations: EA--Effective Address CP--Coprocessor 7-54 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... When the MC68020/EC020 detects a protocol violation, it does not automatically notify the coprocessor of the resulting exception by writing to the control CIR. However, the exception handling routine may use the MOVES instruction to read the response CIR and thus determine the primitive that caused the MC68020/EC020 to initiate protocol violation exception processing. The main processor initiates exception processing using the midinstruction stack frame (refer to Figure 7-43) and the coprocessor protocol violation exception vector number 13. If the exception handler does not modify the stack frame, the main processor reads the response CIR again following the execution of an RTE instruction to return from the exception handler. This protocol allows extensions to the M68000 coprocessor interface to be emulated in software by a main processor that does not provide hardware support for these extensions. Thus, the protocol violation is transparent to the coprocessor if the primitive execution can be emulated in software by the main processor. 7.5.2.2 F-LINE EMULATOR EXCEPTIONS. The F-line emulator exceptions detected by the MC68020/EC020 are either explicitly or implicitly related to the encodings of F-line operation words in the instruction stream. If the main processor determines that an F-line operation word is not valid, it initiates F-line emulator exception processing. Any F-line operation word with bits 8-6 = 110 or 111 causes the MC68020/EC020 to initiate exception processing without initiating any communication with the coprocessor for that instruction. Also, an operation word with bits 8-6 = 000-101 that does not map to one of the valid coprocessor instructions in the instruction set causes the MC68020/EC020 to initiate F-line emulator exception processing. If the F-line emulator exception is either of these two situations, the main processor does not write to the control CIR prior to initiating exception processing. F-line exceptions can also occur if the operations requested by a coprocessor response primitive are not compatible with the effective address type in bits 5-0 of the coprocessor instruction operation word. The F-line emulator exceptions that can result from the use of the M68000 coprocessor response primitives are summarized in Table 7-6. If the exception is caused by receiving an invalid primitive, the main processor aborts the coprocessor instruction in progress by writing an abort mask (refer to 7.3.2 Control CIR) to the control CIR prior to F-line emulator exception processing. Another type of F-line emulator exception occurs when a bus error occurs during the CIR access that initiates a coprocessor instruction. The main processor assumes that the coprocessor is not present and takes the exception. When the main processor initiates F-line emulator exception processing, it uses the fourword preinstruction exception stack frame (refer to Figure 7-41) and the F-line emulator exception vector number 11. Thus, if the exception handler does not modify the stack frame, the main processor attempts to restart the instruction that caused the exception after it executes an RTE instruction to return from the exception handler. If the cause of the F-line exception can be emulated in software, the handler stores the results of the emulation in the appropriate registers of the programming model and in the status register field of the saved stack frame. The exception handler adjusts the program MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-55 Freescale Semiconductor, Inc. counter field of the saved stack frame to point to the next instruction operation word and executes the RTE instruction. The MC68020/EC020 then executes the instruction following the instruction that was emulated. Freescale Semiconductor, Inc... The exception handler should also check the copy of the SR on the stack to determine whether tracing is enabled. If tracing is enabled, the trace exception processing should also be emulated. Refer to Section 6 Exception Processing for additional information. 7.5.2.3 PRIVILEGE VIOLATIONS. Privilege violations can result from the cpSAVE and cpRESTORE instructions and from the supervisor check coprocessor response primitive. The MC68020/EC020 initiates privilege violation exception processing if it attempts to execute either the cpSAVE or cpRESTORE instruction when it is in the user state (S = 0 in the SR). The main processor initiates this exception processing prior to any communication with the coprocessor associated with the cpSAVE or cpRESTORE instructions. If the main processor is executing a coprocessor instruction in the user state when it reads the supervisor check primitive, it aborts the coprocessor instruction in progress by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR). The main processor then performs privilege violation exception processing. If a privilege violation occurs, the main processor initiates exception processing using the four-word preinstruction stack frame (refer to Figure 7-41) and the privilege violation exception vector number 8. Thus, if the exception handler does not modify the stack frame, the main processor attempts to restart the instruction during which the exception occurred after it executes an RTE to return from the handler. 7.5.2.4 cpTRAPcc INSTRUCTION TRAPS. If, during the execution of a cpTRAPcc instruction, the coprocessor returns the TRUE condition indicator to the main processor with a null primitive, the main processor initiates trap exception processing. The main processor uses the six-word postinstruction exception stack frame (refer to Figure 7-45) and the trap exception vector number 7. The scanPC field of this stack frame contains the address of the instruction following the cpTRAPcc instruction. The processing associated with the cpTRAPcc instruction can then proceed, and the exception handler can locate any immediate operand words encoded in the cpTRAPcc instruction using the information contained in the six-word stack frame. If the exception handler does not modify the stack frame, the main processor executes the instruction following the cpTRAPcc instruction after it executes an RTE instruction to exit from the handler. 7.5.2.5 TRACE EXCEPTIONS. The MC68020/EC020 supports two modes of instruction tracing, as discussed in Section 6 Exception Processing. In the trace on instruction execution mode, the MC68020/EC020 takes a trace exception after completing each instruction. In the trace on change of flow mode, the MC68020/EC020 takes a trace exception after each instruction that alters the SR or places an address other than the address of the next instruction in the PC. 7-56 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The protocol used to execute coprocessor cpSAVE, cpRESTORE, or conditional category instructions does not change when a trace exception is pending in the main processor. The main processor performs a pending trace on instruction execution exception after completing the execution of that instruction. If the main processor is in the trace on change of flow mode and an instruction places an address other than that of the next instruction in the PC, the processor takes a trace exception after it executes the instruction. If a trace exception is not pending during a general category instruction, the main processor terminates communication with the coprocessor after reading any primitive with CA = 0. Thus, the coprocessor can complete a cpGEN instruction concurrently with the execution of instructions by the main processor. When a trace exception is pending, however, the main processor must ensure that all processing associated with a cpGEN instruction has been completed before it takes the trace exception. In this case, the main processor continues to read the response CIR and to service the primitives until it receives either a null primitive with CA = 0 and PF = 1 or until exception processing caused by a take postinstruction exception primitive has completed. The coprocessor should return the null primitive with CA = 0 and PF = 0 while it is completing the execution of the cpGEN instruction. The main processor may service pending interrupts between reads of the response CIR if IA = 1 in these primitives (refer to Table 7-3). This protocol ensures that a trace exception is not taken until all processing associated with a cpGEN instruction has completed. If T1, T0 = 01 in the MC68020/EC020 SR (trace on change of flow mode) when a general category instruction is initiated, a trace exception is taken for the instruction only when the coprocessor issues a transfer status register and scanPC primitive with DR = 1 during the execution of that instruction. In this case, it is possible that the coprocessor is still executing the cpGEN instruction concurrently when the main processor begins execution of the trace exception handler. A cpSAVE instruction executed during the trace on change of flow exception handler could thus suspend the execution of a concurrently operating cpGEN instruction. 7.5.2.6 INTERRUPTS. Interrupt processing, discussed in Section 6 Exception Processing, can occur at any instruction boundary. Interrupts are also serviced during the execution of a general or conditional category instruction under either of two conditions. If the main processor reads a null primitive with CA = 1 and IA = 1, it services any pending interrupts prior to reading the response CIR. Similarly, if a trace exception is pending during cpGEN instruction execution and the main processor reads a null primitive with CA = 0, IA = 1, and PF = 0 (refer to 7.5.2.5 Trace Exceptions), the main processor services pending interrupts prior to reading the response CIR again. The MC68020/EC020 uses the 10-word midinstruction stack frame (see Figure 7-43) when it services interrupts during the execution of a general or conditional category coprocessor instruction. Since it uses this stack frame, the main processor can perform all necessary processing and then return to read the response CIR. Thus, it can continue execution of the coprocessor instruction during which the interrupt exception occurred. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-57 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The MC68020/EC020 also services interrupts if it reads the not-ready format word from the save CIR during a cpSAVE instruction. The MC68020/EC020 uses the normal fourword preinstruction stack frame (see Figure 7-41) when it services interrupts after reading the not-ready format word. Thus, the processor can service any pending interrupts and execute an RTE to return and reinitiate the cpSAVE instruction by reading the save CIR. 7.5.2.7 FORMAT ERRORS. The MC68020/EC020 can detect a format error while executing a cpSAVE or cpRESTORE instruction if the length field of a valid format word is not a multiple of four bytes. If the MC68020/EC020 reads a format word with an invalid length field from the save CIR during the cpSAVE instruction, it aborts the coprocessor instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR) and initiates format error exception processing. If the MC68020/EC020 reads a format word with an invalid length field from the effective address specified in the cpRESTORE instruction, the MC68020/EC020 writes that format word to the restore CIR and then reads the coprocessor response from the restore CIR. The MC68020/EC020 then aborts the cpRESTORE instruction by writing an abort mask to the control CIR (refer to 7.3.2 Control CIR) and initiates format error exception processing. The MC68020/EC020 uses the four-word preinstruction stack frame (see Figure 7-41) and the format error vector number 14 when it initiates format error exception processing. Thus, if the exception handler does not modify the stack frame, the main processor, after it executes an RTE to return from the handler, attempts to restart the instruction during which the exception occurred. 7.5.2.8 ADDRESS AND BUS ERRORS. Coprocessor-instruction-related bus faults can occur during main processor bus cycles to CPU space to communicate with a coprocessor or during memory cycles run as part of the coprocessor instruction execution. If a bus error occurs during the CIR access that is used to initiate a coprocessor instruction, the main processor assumes that the coprocessor is not present and takes an F-line emulator exception as described in 7.5.2.2 F-Line Emulator Exceptions. That is, the processor takes an F-line emulator exception when a bus error occurs during the initial access to a CIR by a coprocessor instruction. If a bus error occurs on any other coprocessor access or on a memory access made during the execution of a coprocessor instruction, the main processor performs bus error exception processing as described in Section 6 Exception Processing. After the exception handler has corrected the cause of the bus error, the main processor can return to the point in the coprocessor instruction at which the fault occurred. An address error occurs if the MC68020/EC020 attempts to prefetch an instruction from an odd address. This can occur if the calculated destination address of a cpBcc or cpDBcc instruction is odd or if an odd value is transferred to the scanPC with the transfer status register and the scanPC response primitive. If an address error occurs, the MC68020/EC020 performs exception processing for a bus fault as described in Section 6 Exception Processing. 7-58 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 7.5.3 Coprocessor Reset Either an external reset signal or a RESET instruction can reset the external devices of a system. The system designer can design a coprocessor to be reset and initialized by both reset types or by external reset signals only. To be consistent with the MC68020/EC020 design, the coprocessor should be affected by external reset signals only and not by RESET instructions, because the coprocessor is an extension to the main processor programming model and to the internal state of the MC68020/EC020. 7.6 COPROCESSOR SUMMARY Freescale Semiconductor, Inc... Coprocessor instruction formats are included with the instruction formats in the M68000PM/AD, M68000 Family Programmer's Reference Manual . The M68000 coprocessor response primitive formats are shown in this section. Any response primitive with bits 13-8 = $00 or $3F causes a protocol violation exception. Response primitives with bits 13-8 = $0B, $18-$1B, $1F, $28-$2B, and $38-3B currently cause protocol violation exceptions; they are undefined and reserved for future use by Motorola. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-59 Freescale Semiconductor, Inc. Busy 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 PC 1 0 0 1 0 0 0 0 0 0 0 0 0 0 7 Transfer Multiple Coprocessor Registers 15 14 13 12 11 10 9 8 CA PC DR 0 0 0 0 1 0 LENGTH Transfer Status Register and ScanPC 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 0 0 1 SP 0 0 0 0 0 0 0 0 Freescale Semiconductor, Inc... Supervisor Check 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 1 PC 0 0 0 1 0 0 0 0 0 0 0 0 0 0 7 Take Address and Transfer Data 15 14 13 12 11 10 9 8 CA PC DR 0 0 1 0 1 0 LENGTH Transfer Multiple Main Processor Registers 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 0 1 1 0 0 0 0 0 0 0 0 0 Transfer Operation Word 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 0 1 1 1 0 0 0 0 0 0 0 0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 1 0 0 IA 0 0 0 0 0 0 PF TF Null Evaluate and Transfer Effective Address 7-60 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC 0 0 1 0 1 0 0 0 0 0 0 0 0 0 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Transfer Single Main Processor Register 15 14 13 12 11 10 9 8 7 6 5 4 3 CA PC DR 0 1 1 0 0 0 0 0 0 D/A 2 0 REGISTER Transfer Main Processor Control Register 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 CA PC DR 0 1 1 0 1 0 0 0 0 0 0 0 0 7 Freescale Semiconductor, Inc... Transfer to/from Top of Stack 15 14 13 12 11 10 9 8 CA PC DR 0 1 1 1 0 0 LENGTH Transfer from Instruction Stream 15 14 13 12 11 10 9 8 CA PC 0 0 1 1 1 1 7 0 LENGTH Evaluate Effective Address and Transfer Data 15 14 13 12 11 CA PC DR 1 0 10 9 8 7 VALID EA 0 LENGTH Take Preinstruction Exception 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 0 0 7 0 VECTOR NUMBER Take Midinstruction Exception 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 0 1 7 0 VECTOR NUMBER Take Postinstruction Exception 15 14 13 12 11 10 9 8 0 PC 0 1 1 1 1 0 7 0 VECTOR NUMBER Write to Previously Evaluated Effective Address 15 14 13 12 11 10 9 8 CA PC 1 0 0 0 0 0 MOTOROLA 7 0 LENGTH M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 7-61 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... SECTION 8 INSTRUCTION EXECUTION TIMING This section describes the instruction execution and operations (table searches, etc.) of the MC68020/EC020 in terms of external clock cycles. It provides accurate execution and operation timing guidelines but not exact timings for every possible circumstance. This approach is used since exact execution time for an instruction or operation is highly dependent on memory speeds and other variables. The timing numbers presented in this section allow the assembly language programmer or compiler writer to predict timings needed to evaluate the performance of the MC68020/EC020. In this section, instruction and operation times are shown in clock cycles, which eliminates clock frequency dependencies. 8.1 TIMING ESTIMATION FACTORS The advanced architecture of the MC68020/EC020 makes exact instruction timing calculations difficult due to the effects of: 1. An On-Chip Instruction Cache and Instruction Prefetch 2. Operand Misalignment 3. Bus Controller/Sequence Concurrency 4. Instruction Execution Overlap These factors make MC68020/EC020 instruction set timing difficult to calculate on a single instruction basis since instructions vary in execution time from one context to another. A detailed explanation of each of these factors follows. 8.1.1 Instruction Cache and Prefetch The on-chip cache of the MC68020/EC020 is an instruction-only cache. Its purpose is to increase execution efficiency by providing a quick store for instructions. Instruction prefetches that hit in the cache will occur with no delay in instruction execution. Instruction prefetches that miss in the cache will cause an external memory cycle to be performed, which may overlap with internal instruction execution. Thus, while the execution unit of the microprocessor is busy, the bus controller prefetches the next instruction from external memory. Both cases are illustrated in later examples. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-1 Freescale Semiconductor, Inc. When prefetching instructions from external memory, the microprocessor will utilize longword read cycles. When the read is aligned on a long-word address boundary, the processor reads two words, which may load two instructions at once or two words of a multiword instruction. The subsequent instruction prefetch will find the second word is already available, and there is no need to run an external bus cycle (read). Freescale Semiconductor, Inc... The MC68020/EC020 always prefetches long words. When an instruction prefetch falls on an odd-word boundary (e.g., due to a branch to an odd-word location), the MC68020/EC020 will read the even word associated with the long-word base address at the same time as (32-bit memory) or before (8- or 16-bit memory) the odd word is read. When an instruction prefetch falls on an even-word boundary (as would be the normal case), the MC68020/EC020 reads both words at the long-word address, thus effectively prefetching the next two words. 8.1.2 Operand Misalignment Another significant factor affecting instruction timing is operand misalignment. Operand misalignment has impact on performance when the microprocessor is reading or writing external memory. In this case, the address of a word operand falls across a long-word boundary, or a long-word operand falls on a byte or word address that is not a long-word boundary. Although the MC68020/EC020 will automatically handle all occurrences of operand misalignment, it must use multiple bus cycles to complete such transfers. 8.1.3 Bus/Sequencer Concurrency The bus controller is responsible for all bus activity. The sequencer controls the bus controller, instruction execution, and internal processor operation, such as calculation of effective addresses and setting of condition codes. The bus controller and sequencer can operate on an instruction concurrently. The bus controller can perform a read or write while the sequencer controls an effective address calculation or sets the condition codes. The sequencer may also request a bus cycle that the bus controller cannot immediately perform. In this case, the bus cycle is queued and the bus controller runs the cycle when the current cycle is complete. 8-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.1.4 Instruction Execution Overlap Overlap is the time, measured in clocks, when two instructions execute concurrently. In Figure 8-1, instructions A and B execute concurrently, and the overlapped portion of instruction B is absorbed in the instruction execution time of A (the previous instruction). The overlap time is deducted from the execution time of instruction B. Similarly, there is an overlap period between instruction B and instruction C, which reduces the attributed execution time for C. INSTRUCTION A INSTRUCTION B Freescale Semiconductor, Inc... INSTRUCTION C OVERLAP OVERLAP Figure 8-1. Concurrent Instruction Execution The execution time attributed to instructions A, B, and C (after considering the overlap) is depicted in Figure 8-2. INSTRUCTION A INSTRUCTION B INSTRUCTION C OVERLAP PERIOD (ABSORBED BY INSTRUCTION A) OVERLAP PERIOD (ABSORBED BY INSTRUCTION B) Figure 8-2. Instruction Execution for Instruction Timing Purposes It is possible that the execution time of an instruction will be absorbed by the overlap with a previous instruction for a net execution time of zero clocks. Because of this overlap, a NOP is required between a write to a peripheral to clear an interrupt request and a subsequent MOVE to SR instruction to lower the interrupt mask level. Otherwise, the MOVE to SR instruction may complete before the write is accomplished, and a new interrupt exception will be generated for an old interrupt request. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-3 Freescale Semiconductor, Inc. 8.1.5 Instruction Stream Timing Examples A programming example allows a more detailed examination of these effects. The effect of instruction execution overlap on instruction timing is illustrated by the following example instruction stream. Instruction #1) MOVE.L D4,(A1)+ #2) ADD.L D4,D5 #3) MOVE.L (A1), -(A2) #4) ADD.L D5,D6 Freescale Semiconductor, Inc... Example 1 For the first example, the assumptions are: 1. The data bus is 32 bits, 2. The first instruction is prefetched from an odd-word address, 3. Memory access occurs with no wait states, and 4. The instruction cache is disabled. For example 1, the instruction stream is positioned in 32-bit memory as follows: Address n *** MOVE #1 n+4 ADD #2 MOVE #3 n+8 ADD #4 *** Figure 8-3 shows processor activity on the first example instruction stream. It shows the activity of the external bus, the bus controller, the sequencer, and the attributed instruction execution time. 8-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 1 2 4 3 5 6 7 8 9 10 11 12 13 14 15 16 17 CLOCK BUS ACTIVITY PREFETCH WRITE READ PREFETCH WRITE BUS CONTROLLER PREFETCH BYTES n + 8 WRITE TO (A1)+ READ FROM (A1) PREFETCH BYTES n + 12 WRITE TO -(A2) SEQUENCER PERFORM MOVE #1 INSTRUCTION EXECUTION TIME MOVE.L D4,(A1)+ CLOCK COUNT Freescale Semiconductor, Inc... PERFORM ADD #2 IDLE CALCULATE CALCULATE SOURCE EA DESTINATION EA MOVE #3 MOVE #3 IDLE MOVE.L (A1),-(A2) (6) (9) PERFORM MOVE #3 IDLE PERFORM ADD #4 ADD.L D5,D6 (1) LEGEND: 1) MOVE.L D4,(A1)+ 2) ADD.L D4,D5 3) MOVE.L (A1),-(A2) 4) ADD.L D5,D6 Figure 8-3. Processor Activity for Example 1 For the first three clocks of this example, the bus controller and sequencer are both performing tasks associated with the MOVE #1 instruction. The next three clocks (clocks 4, 5, and 6) demonstrate instruction overlap. The bus controller is performing a write to memory as part of the MOVE #1 instruction. The sequencer, on the other hand, is performing the ADD #2 instruction for two clocks (clocks 4 and 5) and beginning source effective address (EA) calculations for the MOVE #3 instruction. The bus controller activity completely overlaps the execution of the ADD #2 instruction, causing the ADD #2 attributed execution time to be zero clocks. The overlap also shortens the effective execution time of the MOVE #3 instruction by one clock because the bus controller completes the MOVE #1 write operation while the sequencer begins the MOVE #3 EA calculation. The sequencer continues the source EA calculation for one more clock period (clock 7) while the bus controller begins a read for MOVE #3. When counting instruction execution time in bus clocks, the MOVE #1 completes at the end of clock 6, and the execution of MOVE #3 begins on clock 7. Both the sequencer and bus controller continue with MOVE #3 until the end of clock 14, when the sequencer begins to perform ADD #4. Timing for MOVE #3 continues because the bus controller is still performing the write to the destination of MOVE #3. The bus activity for MOVE #3 completes at the end of clock 15. The effective execution time for MOVE #3 is nine clocks. The one clock cycle (clock 15) when the sequencer is performing ADD #4 and the bus controller is writing to the destination of MOVE #3 is absorbed by the execution time of MOVE #3. This overlap shortens the effective execution time of ADD #4 by one clock, giving it an attributed execution time of one clock. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-5 Freescale Semiconductor, Inc. Example 2 Using the same instruction stream, the second example demonstrates the different effects of instruction execution overlap on instruction timing when the same instructions are positioned slightly differently in 32-bit memory: Freescale Semiconductor, Inc... Address n MOVE #1 ADD #2 n+4 MOVE #3 ADD #4 n+8 *** *** The assumptions for example 2 (see Figure 8-4) are: 1. The data bus is 32 bits, 2. The first instruction is prefetched from an even-word address, 3. Memory access occurs with no wait states, and 4. The cache is disabled. 1 2 4 3 5 6 7 8 9 10 11 12 13 14 15 16 17 CLOCK BUS ACTIVITY BUS CONTROLLER SEQUENCER INSTRUCTION EXECUTION TIME IDLE WRITE PREFETCH WRITE TO (A1)+ PREFETCH BYTES n + 8 PERFORM MOVE #1 PERFORM ADD #2 CALCULATE SOURCE EA MOVE #3 READ READ FROM (A1) CALCULATE IDLE DESTINATION IDLE EA MOVE #3 WRITE PREFETCH WRITE TO -(A2) PREFETCH BYTES n + 12 PERFORM MOVE #3 MOVE.L D4,(A1)+ ADD.L D4,D5 MOVE.L (A1),-(A2) (4) (3) (6) CLOCK COUNTER PERFORM ADD #4 NEXT INSTRUCTION ADD.L D5,D6 (3) LEGEND: 1) MOVE.L D4,(A1)+ 2) ADD.L D4,D5 3) MOVE.L (A1),-(A2) 4) ADD.L D5,D6 Figure 8-4. Processor Activity for Example 2 Although the total execution time of the instruction segment does not change in this example, the individual instruction times are significantly different. This example demonstrates that the effects of overlap are not only instruction-sequence dependent but are also dependent upon the alignment of the instruction stream in memory. 8-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Example 3 Both Figures 8-3 and 8-4 show instruction execution without benefit of the MC68020/EC020 instruction cache. Figure 8-5 shows a third example for the same instruction stream executing in the cache. Note that once the instructions are in the cache, the original location in external memory is no longer a factor in timing. The assumptions for Example 3 are: 1. The data bus is 32 bits, 2. The cache is enabled and instructions are in the cache, and 3. Memory access occurs with no wait states. Freescale Semiconductor, Inc... 1 2 4 3 5 6 8 7 9 10 11 12 13 CLOCK BUS ACTIVITY BUS CONTROLLER SEQUENCER INSTRUCTION EXECUTION TIME WRITE IDLE WRITE TO (A1)+ PERFORM MOVE #1 PERFORM ADD #2 IDLE READ WRITE READ FROM (A1) WRITE TO -(A2) CALCULATE CALCULATE SOURCE EA DESTINATION EA MOVE #3 MOVE #3 PERFORM MOVE #3 IDLE PERFORM ADD #4 MOVE.L D4,(A1)+ MOVE.L (A1),-(A2) ADD.L D5,D6 (4) (7) (1) CLOCK COUNTER LEGEND: 1) MOVE.L D4,(A1)+ 2) ADD.L D4,D5 3) MOVE.L (A1),-(A2) 4) ADD.L D5,D6 Figure 8-5. Processor Activity for Example 3 Figure 8-5 illustrates the benefits of the instruction cache. The total number of clock cycles is reduced from 16 to 12 clocks. Since the instructions are resident in the cache, the instruction prefetch activity does not require the bus controller to perform external bus cycles. Since prefetch occurs with no delay, the bus controller is idle more often. Example 4 Idle clock cycles, such as those shown in example 3, are useful in MC68020/EC020 systems that require wait states when accessing external memory. This fact is illustrated in example 4 (see Figure 8-6) with the following assumptions: 1. The data bus is 32 bits, 2. The cache is enabled and instructions are in the cache, and 3. Memory access occurs with one wait state. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-7 Freescale Semiconductor, Inc. 1 2 4 3 5 6 7 8 9 10 11 12 13 14 CLOCK BUS ACTIVITY BUS CONTROLLER WRITE TO (A1)+ IDLE PERFORM MOVE #1 SEQUENCER INSTRUCTION EXECUTION TIME PERFORM ADD #2 WRITE READ FROM (A1) WRITE TO -(A2) CALCULATE CALCULATE DESTINATION IDLE SOURCE EA EA MOVE #3 MOVE #3 PERFORM MOVE #3 PERFORM ADD #4 MOVE.L (A1),-(A2) MOVE.L D4,(A1)+ CLOCK COUNTER Freescale Semiconductor, Inc... READ WRITE (5) (8) LEGEND: 1) MOVE.L D4,(A1)+ 2) ADD.L D4,D5 3) MOVE.L (A1),-(A2) 4) ADD.L D5,D6 Figure 8-6. Processor Activity for Example 4 Figure 8-6 shows the same instruction stream executing with four clocks for every read and write. The idle bus cycles coincide with the wait states of the memory access; therefore, the total execution time is only 13 clocks. Examples 1-4 demonstrate the complexity of instruction timing calculation for the MC68020/EC020. It is impossible to anticipate individual instruction timing as an absolute number of clock cycles due to the dependency of overlap on the instruction sequence and alignment as well as the number of wait states in memory. This can be seen by comparing individual and composite time for Figures 8-3 through 8-6. These instruction timings are compared in Table 8-1, where timing varies for each instruction as the context varies. Table 8-1. Examples 1-4 Instruction Stream Execution Comparison Instruction #1) MOVE.L #2) ADD.L #3) MOVE.L #4) ADD.L D4,(A1)+ D4,D5 (A1),-(A2) D5,D6 Total Clock Cycles 8-8 Example 1 (Odd Alignment) Example 2 (Even Alignment) Example 3 (Cache) Example 4 (Cache with Wait States) 6 0 9 1 4 3 6 3 4 0 7 1 5 0 8 0 16 16 12 13 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2 INSTRUCTION TIMING TABLES Freescale Semiconductor, Inc... The instruction times given in the following illustration include the following assumptions about the MC68020/EC020 system: 1. All operands are long-word aligned as is the stack, 2. The data bus is 32 bits, and 3. Memory access occurs with no wait states (three-cycle read/write). There are three values given for each instruction and addressing mode: 1. The best case (BC), which reflects the time (in clocks) when the instruction is in the cache and benefits from maximum overlap due to other instructions, 2. The cache-only case (CC) when the instruction is in the cache but has no overlap, and 3. The worst case (WC) when the instruction is not in the cache or the cache is disabled and there is no instruction overlap. The only instances for which the size of the operand has any effect are the instructions with immediate operands. Unless specified otherwise, immediate byte and word operands have identical execution times. Within each set or column of instruction timings are four sets of numbers, three of which are enclosed in parentheses. The bolded outer number is the total number of clocks for the instruction. The first number inside the parentheses is the number of operand read cycles performed by the instruction. The second value inside parentheses is the number of instruction accesses performed by the instruction, including all prefetches to keep the instruction pipe filled. The third value within parentheses is the number of write cycles performed by the instruction. One example from the instruction timing table is: 24 (2 / 3 / 0) TOTAL NUMBER OF CLOCKS NUMBER OF READ CYCLES NUMBER OF INSTRUCTION ACCESS CYCLES NUMBER OF WRITE CYCLES The total number of bus-activity clocks for the previous example is derived in the following way: (2 Reads * 3 Clocks/Read) + (3 Instruction Accesses * 3 Clocks/Access) + (0 Writes * 3 Clocks/Write) = 15 Clocks of Bus Activity 24 Total Clocks - 15 Clocks (Bus Activity) = 9 Internal Clocks The example used here was taken from a worst-case fetch effective address time. The addressing mode was ([d 32,B],I,d32). The same addressing mode under the best-case MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-9 Freescale Semiconductor, Inc. entry is 17 (2/0/0). For the best case, there are no instruction accesses because the cache is enabled and the sequencer does not have to go to external memory for the instruction words. Freescale Semiconductor, Inc... The first tables deal exclusively with fetching and calculating effective addresses and immediate operands. The tables are arranged in this manner because some instructions do not require effective address calculation or fetching. For example, the instruction CLR (found in the table under 8.2.11 Single Operand Instructions) only needs to have a calculated effective address time added to its table entry because no fetch of an operand is required. This instruction only writes to memory or a register. Some instructions use specific addressing modes which exclude timing for calculation or fetching of an operand. When these instances arise, they are footnoted to indicate which other tables are needed in the timing calculation. Many two-word instructions (e.g., MULU.L, DIV.L, BFSET, etc.) include the fetch immediate effective address time or the calculate immediate effective address time in the execution time calculation. The timing for immediate data of word length (#.W) is used for these calculations. If the instruction has a source and a destination, the source effective address is used for the table lookup. If the instruction is single operand, the effective address of that operand is used. The following example includes multiword instructions that refer to the fetch immediate effective address and calculate immediate effective address tables in 8.2 Instruction Timing Tables. Instruction #1) MULU.L D7,D1:D2 #2) BFCLR $6000{0:8} #3) DIVS.L #$10000,D3:D4 CC 1.MULU.L (D7),D1:D2 #.W,Dn 2 MUL.L EA,Dn 43 2.BFCLR $6000{0:8} #.W.,$XXX.W BFCLR Mem (<5 bytes) 3.DIVS.L #$10000,D3:D4 #.W,#.L DIVS.L EA, Dn 5 16 6 90 Execution time = 2 + 43 + 5 + 16 + 6 + 90 = 102 clock periods 8-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. NOTE This CC time is a maximum since the times given for the MULU.L and DIVS.L are maximums. The MOVE instruction timing tables include all necessary timing for extension word fetch, address calculation, and operand fetch. Freescale Semiconductor, Inc... The instruction timing tables are used to calculate a best-case and worst-case bounds for some target instruction stream. Calculating exact timing from the timing tables is impossible because the tables cannot anticipate how the combination of factors will influence every particular sequence of instructions. This is illustrated by comparing the observed instruction timing from the prior four examples with instruction timing derived from the instruction timing tables. Table 8-2 lists the original instruction stream and the corresponding clock timing from the appropriate timing tables for the best case, cache-only case, and worst case. Table 8-2. Instruction Timings from Timing Tables Instruction Best Case Cache Case Worst Case 4 0 6 0 4 2 7 2 6 3 9 3 10 15 21 D4,(A1)+ D4,D5 (A1),-(A2) D5,D6 #1) MOVE.L #2) ADD.L #3) MOVE.L #4) ADD.L Total Table 8-3 summarizes the observed instruction timings for the same instruction stream as executed according to the assumptions of the four examples. For each example, Table 83 shows which entry (BC/CC/WC) from the timing tables corresponds to the observed timing for each of the four instructions. Some of the observed instruction timings cannot be found in the timing tables and appear in Table 8-3 within parentheses in the most appropriate column. These timings occur when instruction execution overlap dynamically alters what would otherwise be a BC, CC, or WC timing. Table 8-3. Observed Instruction Timings Example 1 Instruction #1) MOVE.L #2) ADD.L #3) MOVE.L #4) ADD.L Total MOTOROLA D4,(A1)+ D4,D5 (A1),-(A2) D5,D6 BC CC Example 2 WC BC 6 4 9 6 CC Example 3 WC CC WC BC 4 0 3 0 3 (16) CC WC (5) 0 7 (1) (16) BC Example 4 (1) (8) 0 (12) M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com (13) 8-11 Freescale Semiconductor, Inc. Comparing Tables 8-2 and 8-3 demonstrates that calculation of instruction timing cannot be a simple lookup of only BC or only WC timings. Even when the assumptions are known and fixed, as in the four examples summarized in Table 8-3, the microprocessor can sometimes achieve best-case timings under worst-case assumptions. Freescale Semiconductor, Inc... Looking across the four examples in Table 8-3 for an individual instruction, it is difficult to predict which timing table entry is used, since the influence of instruction overlap may or may not improve the BC, WC, or CC timings. When looking at the observed instruction timings for one example, it is also difficult to determine which combination of BC/CC/WC timing is required. Just how the instruction stream will fit and run with the cache enabled, how instructions are positioned in memory, and the degree of instruction overlap are factors that are impossible to account for in all combinations of the timing tables. Although the timing tables cannot accurately predict the instruction timing that would be observed when executing an instruction stream on the MC68020/EC020, the tables can be used to calculate best-case and worst-case bounds for instruction timing. Absolute instruction timing must be measured by using the microprocessor itself to execute the target instruction stream. 8-12 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.1 Fetch Effective Address The fetch effective address table indicates the number of clock periods needed for the processor to calculate and fetch the specified effective address. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case Dn 0(0/0/0) 0(0/0/0) 0(0/0/0) An 0(0/0/0) 0(0/0/0) 0(0/0/0) (An) 3(1/0/0) 4(1/0/0) 4(1/0/0) (An)+ 4(1/0/0) 4(1/0/0) 4(1/0/0) -(An) 3(1/0/0) 5(1/0/0) 5(1/0/0) (d 16 ,An) of (d16 ,PC) 3(1/0/0) 5(1/0/0) 6(1/1/0) (xxx).W 3(1/0/0) 4(1/0/0) 6(1/1/0) (xxx).L 3(1/0/0) 4(1/0/0) 7(1/1/0) #.B 0(0/0/0) 2(0/0/0) 3(0/1/0) #.W 0(0/0/0) 2(0/0/0) 3(0/1/0) #.L 0(0/0/0) 4(0/0/0) 5(0/1/0) (d 8,An,Xn) or (d8,PC,Xn) 4(1/0/0) 7(1/0/0) 8(1/1/0) (d 16 ,An,Xn) or (d16 ,PC,Xn) 4(1/0/0) 7(1/0/0) 9(1/1/0) (B) 4(1/0/0) 7(1/0/0) 9(1/1/0) (d 16 ,B) 6(1/0/0) 9(1/0/0) 12(1/1/0) (d 32 ,B) 10(1/0/0) 13(1/0/0) 16(1/2/0) ([B],I) 9(2/0/0) 12(2/0/0) 13(2/1/0) ([B],I,d 16 ) 11(2/0/0) 14(2/0/0) 16(2/1/0) ([B],I,d 32 ) 11(2/0/0) 14(2/0/0) 17(2/2/0) ([d16 ,B],I) 11(2/0/0) 14(2/0/0) 16(2/1/0) ([d16 ,B],I,d 16 ) 13(2/0/0) 16(2/0/0) 19(2/2/0) ([d16 ,B],I,d 32 ) 13(2/0/0) 16(2/0/0) 20(2/2/0) ([d32 ,B],I) 15(2/0/0) 18(2/0/0) 20(2/2/0) ([d32 ,B],I,d 16 ) 17(2/0/0) 20(2/0/0) 22(2/2/0) ([d32 ,B],I,d 32 ) 17(2/0/0) 20(2/0/0) 24(2/3/0) B = Base address; 0, An, PC, Xn, An + Xn. Form does not affect timing. I = Index; 0, Xn NOTE: Xn cannot be in B and I at the same time. Scaling and size of Xn do not affect timing. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-13 Freescale Semiconductor, Inc. 8.2.2 Fetch Immediate Effective Address The fetch immediate effective address table indicates the number of clock periods needed for the processor to fetch the immediate source operand and calculate and fetch the specified destination operand. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case #.W,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) #.L,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) #.W,(An) 3(1/0/0) 4(1/0/0) 4(1/1/0) #.L,(An) 3(1/0/0) 4(1/0/0) 7(1/1/0) #.W,(An)+ 4(1/0/0) 6(1/0/0) 7(1/1/0) #.L,(An)+ 5(1/0/0) 8(1/0/0) 9(1/1/0) #.W,-(An) 3(1/0/0) 5(1/0/0) 6(1/1/0) #.L,-(An) 4(1/0/0) 7(1/0/0) 8(1/1/0) #.W,(bd,An) 3(1/0/0) 5(1/0/0) 7(1/1/0) #.L,(bd,An) 4(1/0/0) 7(1/0/0) 10(1/2/0) #.W,xxx.W 3(1/0/0) 5(1/0/0) 7(1/1/0) #.L,xxx.W 4(1/0/0) 7(1/0/0) 10(1/2/0) #.W,xxx.L 3(1/0/0) 6(1/0/0) 10(1/2/0) #.L,xxx.L 4(1/0/0) 8(1/0/0) 12(1/2/0) #.W,#.B,W 0(0/0/0) 4(0/0/0) 6(0/2/0) #.L,#.B,W 1(0/0/0) 6(0/0/0) 8(0/2/0) #.W,#.L 0(0/0/0) 6(0/0/0) 8(0/2/0) #.L,#(data>.L 1(0/0/0) 8(0/0/0) 10(0/2/0) #.W,(d8,An,Xn) or (d8,PC,Xn) 4(1/0/0) 9(1/0/0) 11(1/2/0) #.L,(d8,An,Xn) or (d8,PC,Xn) 5(1/0/0) 11(1/0/0) 13(1/2/0) #.W,(d16,An,Xn) or (d16,PC,Xn) 4(1/0/0) 9(1/0/0) 12(1/2/0) #.L,(d16,An,Xn) or (d16,PC,Xn) 5(1/0/0) 11(1/0/0) 15(1/2/0) #.W,(B) 4(1/0/0) 9(1/0/0) 12(1/1/0) #.L,(B) 5(1/0/0) 11(1/0/0) 14(1/2/0) #.W,(bd,PC) 10(1/0/0) 15(1/0/0) 19(1/3/0) #.L,(bd,PC) 11(1/0/0) 17(1/0/0) 21(1/3/0) #.W,(d16,B) 6(1/0/0) 11(1/0/0) 15(1/2/0) #.L,(d16,B) 7(1/0/0) 13(1/0/0) 17(1/2/0) #.W,(d32,B) 10(1/0/0) 15(1/0/0) 19(1/3/0) #.L,(d32,B) 11(1/0/0) 17(1/0/0) 21(1/3/0) #.W,([B],I) 9(2/0/0) 14(2/0/0) 16(2/2/0) #.L,([B],I) 10(2/0/0) 16(2/0/0) 18(2/2/0) #.W,([B],I,d 16) 11(2/0/0) 16(2/0/0) 19(2/2/0) #.L,([B],I,d16) 12(2/0/0) 18(2/0/0) 21(2/2/0) 8-14 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case #.W,([B],I,d 32) 11(2/0/0) 16(2/0/0) 20(2/2/0) #.L,([d16,B],I,d 32) 12(2/0/0) 18(2/0/0) 22(2/3/0) #.W,([d 16,B],I) 11(2/0/0) 16(2/0/0) 19(2/2/0) #.L,([d16,B],I) 12(2/0/0) 18(2/0/0) 21(2/2/0) #.W,([d 16,B],I,d 16) 13(2/0/0) 18(2/0/0) 22(2/2/0) #.L,([d16,B],I,d 16) 14(2/0/0) 20(2/0/0) 24(2/3/0) #.W,([d 32,B],I) 15(2/0/0) 20(2/0/0) 23(2/3/0) #.L,([d32,B],I) 16(2/0/0) 22(2/0/0) 25(2/3/0) #.W,([d 32,B],I,d 16) 17(2/0/0) 22(2/0/0) 25(2/3/0) #.L,([d32,B],I,d 16) 18(2/0/0) 24(2/0/0) 27(2/3/0) #.W,([d 32,b],I,d 32) 17(2/0/0) 22(2/0/0) 27(2/3/0) #.L,([d32,b],I,d 32) 18(2/0/0) 24(2/0/0) 29(2/4/0) B = Base address; 0, An, PC, Xn, An + Xn. Form does not affect timing. I = Index; 0, Xn NOTE: Xn cannot be in B and I at the same time. Scaling and size of Xn do not affect timing. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-15 Freescale Semiconductor, Inc. 8.2.3 Calculate Effective Address The calculate immediate effective address table indicates the number of clock periods needed for the processor to calculate the specified effective address. Fetch time is only included for the first level of indirection on memory indirect addressing modes. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case Dn 0(0/0/0) 0(0/0/0) 0(0/0/0) An 0(0/0/0) 0(0/0/0) 0(0/0/0) (An) 2(0/0/0) 2(0/0/0) 2(0/0/0) (An)+ 2(0/0/0) 2(0/0/0) 2(0/0/0) -(An) 2(0/0/0) 2(0/0/0) 2(0/0/0) (d 16,An) or (d16,PC) 2(0/0/0) 2(0/0/0) 3(0/1/0) .W 2(0/0/0) 2(0/0/0) 3(0/1/0) .L 1(0/0/0) 4(0/0/0) 5(0/1/0) (d 8,An,Xn) or (d8,PC,Xn) 1(0/0/0) 4(0/0/0) 5(0/1/0) (d 16 ,An,Xn) or (d16 ,PC,Xn) 3(0/0/0) 6(0/0/0) 7(0/1/0) (B) 3(0/0/0) 6(0/0/0) 7(0/1/0) (d 16 ,B) 5(0/0/0) 8(0/0/0) 10(0/1/0) (d 32 ,B) 9(0/0/0) 12(0/0/0) 15(0/2/0) ([B],I) 8(1/0/0) 11(1/0/0) 12(1/1/0) ([B],I,d 16 ) 10(1/0/0) 13(1/0/0) 15(1/1/0) ([B],I,d 32 ) 10(1/0/0) 13(1/0/0) 16(1/2/0) ([d16 ,B],I) 10(1/0/0) 13(1/0/0) 15(1/1/0) ([d16 ,B],I,d 16 ) 12(1/0/0) 15(1/0/0) 18(1/2/0) ([d16 ,B],I,d 32 ) 12(1/0/0) 15(1/0/0) 19(1/2/0) ([d32 ,B],I) 14(1/0/0) 17(1/0/0) 19(1/2/0) ([d32 ,B],I,d 16 ) 16(1/0/0) 19(1/0/0) 21(1/2/0) ([d32 ,B],I,d 32 ) 16(1/0/0) 19(1/0/0) 24(1/3/0) B = Base address; 0, An, PC, Xn, An + Xn. Form does not affect timing. I = Index; 0, Xn NOTE: Xn cannot be in B and I at the same time. Scaling and size of Xn do not affect timing. 8-16 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.4 Calculate Immediate Effective Address The calculate immediate effective address table indicates the number of clock periods needed for the processor to fetch the immediate source operand and calculate the specified destination effective address. Fetch time is only included for the first level of indirection on memory indirect addressing modes. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case #.W,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) #.L,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) #.W,(An) 0(0/0/0) 2(0/0/0) 3(0/1/0) #.L,(An) 1(0/0/0) 4(0/0/0) 5(0/1/0) #.W,(An)+ 2(0/0/0) 4(0/0/0) 5(0/1/0) #.L,(An)+ 3(0/0/0) 6(0/0/0) 7(0/1/0) #.W,(bd,An) 1(0/0/0) 4(0/0/0) 5(0/1/0) #.L,(bd,An) 3(0/0/0) 6(0/0/0) 8(0/2/0) #.W,xxx.W 1(0/0/0) 4(0/0/0) 5(0/1/0) #.L,xxx.W 3(0/0/0) 6(0/0/0) 8(0/2/0) #.W,xxx.L 2(0/0/0) 4(0/0/0) 6(0/2/0) #.L,xxx.L 3(0/0/0) 8(0/0/0) 10(0/2/0) #.W,(d8,An,Xn) or (d8,PC,Xn) 0(0/0/0) 6(0/0/0) 8(0/2/0) #.L,(d8,An,Xn) or (d8,PC,Xn) 2(0/0/0) 8(0/0/0) 10(0/2/0) #.W,(d16 ,An,Xn) or (d16 ,PC,Xn) 3(0/0/0) 8(0/0/0) 10(0/2/0) #.L,(d16 ,An,Xn) or (d16 ,PC,Xn) 4(0/0/0) 10(0/0/0) 12(0/2/0) #.W,(B) 3(0/0/0) 8(0/0/0) 10(0/1/0) #.L,(B) 4(0/0/0) 10(0/0/0) 12(0/2/0) #.W,(bd,PC) 9(0/0/0) 14(0/0/0) 18(0/3/0) #.L,(bd,PC) 10(0/0/0) 16(0/0/0) 20(0/3/0) #.W,(d16 ,B) 5(0/0/0) 10(0/0/0) 13(0/2/0) #.L,(d16 ,B) 6(0/0/0) 12(0/0/0) 15(0/2/0) #.W,(d32 ,B) 9(0/0/0) 14(0/0/0) 18(0/2/0) #.L,(d32 ,B) 10(0/0/0) 16(0/0/0) 20(0/3/0) #.W,([B],I) 8(1/0/0) 13(1/0/0) 15(1/2/0) #.L,([B],I) 9(1/0/0) 15(1/0/0) 17(1/2/0) #.W,([B],I,d 16 ) 10(1/0/0) 15(1/0/0) 18(1/2/0) #.L,([B],I,d16 ) 11(1/0/0) 17(1/0/0) 20(1/2/0) #.W,([B],I,d 32 ) 10(1/0/0) 15(1/0/0) 19(1/2/0) #.L,([d16,B],I,d 32 ) 11(1/0/0) 17(1/0/0) 21(1/3/0) #.W,([d 16 ,B],I) 10(1/0/0) 15(1/0/0) 18(1/2/0) #.L,([d16 ,B],I) 11(1/0/0) 17(1/0/0) 20(1/2/0) #.W,([d 16 ,B],I,d 16 ) 12(1/0/0) 17(1/0/0) 21(1/2/0) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-17 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case #.L,([d16 ,B],I,d 16 ) 13(1/0/0) 19(1/0/0) 23(1/3/0) #.([d 16 ,B],I,d 32 ) 12(1/0/0) 17(1/0/0) 22(1/3/0) #.([d 16 ,B],I,d 32 ) 13(1/0/0) 19(1/0/0) 24(1/3/0) #.W,([d 32 ,B],I) 14(1/0/0) 19(1/0/0) 22(1/3/0) #.L,([d32 ,B],I) 15(1/0/0) 21(1/0/0) 24(1/3/0) #.W,([d 32 ,B],I,d 16 ) 16(1/0/0) 21(1/0/0) 24(1/3/0) #.L,([d32 ,B],I,d 16 ) 17(1/0/0) 23(1/0/0) 26(1/3/0) #.W,([d 32 ,B],I,d 32 ) 16(1/0/0) 21(1/0/0) 24(1/3/0) #.L,([d32 ,B],I,d 32 ) 17(1/0/0) 23(1/0/0) 29(1/4/0) B = Base address; 0, An, PC, Xn, An + Xn. Form does not affect timing. I = Index; 0, Xn NOTE: Xn cannot be in B and I at the same time. Scaling and size of Xn do not affect timing. 8-18 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.5 Jump Effective Address The jump effective address table indicates the number of clock periods needed for the processor to calculate the specified effective address. Fetch time is only included for the first level of indirection on memory indirect addressing modes. The total number of clock cycles is outside the parentheses; the number or read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Address Mode Best Case Cache Case Worst Case (An) 0(0/0/0) 2(0/0/0) 2(0/0/0) (d 16 ,An) 1(0/0/0) 4(0/0/0) 4(0/0/0) (xxx).W 0(0/0/0) 2(0/0/0) 2(0/0/0) (xxx).L 0(0/0/0) 2(0/0/0) 2(0/0/0) (d 8,An,Xn) or (d8,PC,Xn) 3(0/0/0) 6(0/0/0) 6(0/0/0) (d 16 ,An,Xn) or (d16 ,PC,Xn) 3(0/0/0) 6(0/0/0) 6(0/0/0) (B) 3(0/0/0) 6(0/0/0) 6(0/0/0) (B,d 16 ) 5(0/0/0) 8(0/0/0) 8(0/1/0) (B,d 32 ) 9(0/0/0) 12(0/0/0) 12(0/1/0) ([B],I) 8(1/0/0) 11(1/0/0) 11(1/1/0) ([B],I,d 16 ) 10(1/0/0) 13(1/0/0) 14(1/1/0) ([B],I,d 32 ) 10(1/0/0) 13(1/0/0) 14(1/1/0) ([d16 ,B],I) 10(1/0/0) 13(1/0/0) 14(1/1/0) ([d16 ,B],I,d 16 ) 12(1/0/0) 15(1/0/0) 17(1/1/0) ([d16 ,B],I,d 32 ) 12(1/0/0) 15(1/0/0) 17(1/1/0) ([d32 ,B],I) 14(1/0/0) 17(1/0/0) 19(1/2/0) ([d32 ,B],I,d 16 ) 16(1/0/0) 19(1/0/0) 21(1/2/0) ([d32 ,B],I,d 32 ) 16(1/0/0) 19(1/0/0) 23(1/2/0) B = Base address; 0, An, PC, Xn, An + Xn, PC + Xn. Form does not affect timing. I = Index; 0, Xn NOTE: Xn cannot be in B and I at the same time. Scaling and size of Xn do not affect timing. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-19 Freescale Semiconductor, Inc. 8.2.6 MOVE Instruction The MOVE instruction table indicates the number of clock periods needed for the processor to fetch, calculate, and perform the MOVE or MOVEA with the specified source and destination effective addresses, including both levels of indirection on memory indirect addressing modes. No additional tables are needed to calculate the total effective execution time for the MOVE or MOVEA instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. BEST CASE Destination Freescale Semiconductor, Inc... Source Address Mode An Dn (An) (An)+ -(An) (d16 ,An) (xxx).W (xxx).L Rn 0(0/0/0) 0(0/0/0) 3(0/0/1) 4(0/0/1) 3(0/0/1) 3(0/0/1) 3(0/0/1) 5(0/0/1) #.B,W 0(0/0/0) 0(0/0/0) 3(0/0/1) 4(0/0/1) 3(0/0/1) 3(0/0/1) 3(0/0/1) 5(0/0/1) #.L 0(0/0/0) 0(0/0/0) 3(0/0/1) 4(0/0/1) 3(0/0/1) 3(0/0/1) 3(0/0/1) 5(0/0/1) (An) 3(1/0/0) 3(1/0/0) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 8(1/0/1) (An)+ 4(1/0/0) 4(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) -(An) 3(1/0/0) 3(1/0/0) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 8(1/0/1) (d 16 ,An) or (d16 ,PC) 3(1/0/0) 3(1/0/0) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 8(1/0/1) (xxx).W 3(1/0/0) 3(1/0/0) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 8(1/0/1) (xxx).L 3(1/0/0) 3(1/0/0) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 6(1/0/1) 8(1/0/1) (d 8,An,Xn) or (d8,PC,Xn) 4(1/0/0) 4(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (d 16 ,An,Xn) or (d16 ,PC,Xn) 4(1/0/0) 4(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (B) 4(1/0/0) 4(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (d 16 ,B) 6(1/0/0) 6(1/0/0) 9(1/0/1) 9(1/0/1) 9(1/0/1) 9(1/0/1) 9(1/0/1) 11(1/0/1) (d 32 ,B) 10(1/0/0) 10(1/0/0) 13(1/0/1) 13(1/0/1) 13(1/0/1) 13(1/0/1) 13(1/0/1) 15(1/0/1) 12(2/0/1) 12(2/0/1) 12(2/0/1) 12(2/0/1) 12(2/0/1) 14(2/0/1) ([B],I) 9(2/0/0) 9(2/0/0) ([B],I,d 16 ) 11(2/0/0) 11(2/0/0) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 16(2/0/1) ([B],I,d 32 ) 11(2/0/0) 11(2/0/0) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 16(2/0/1) ([d16 ,B],I) 11(2/0/0) 11(2/0/0) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 14(2/0/1) 16(2/0/1) ([d16 ,B],I,d 16 ) 13(2/0/0) 13(2/0/0) 16(2/0/1) 16(2/0/1) 16(2/0/1) 16(2/0/1) 16(2/0/1) 18(2/0/1) ([d16 ,B],d 32 ) 13(2/0/0) 13(2/0/0) 16(2/0/1) 16(2/0/1) 16(2/0/1) 16(2/0/1) 16(2/0/1) 18(2/0/1) ([d32 ,B],I) 15(2/0/0) 15(2/0/0) 18(2/0/1) 18(2/0/1) 18(2/0/1) 18(2/0/1) 18(2/0/1) 20(2/0/1) ([d32 ,B],I,d 16 ) 17(2/0/0) 17(2/0/0) 20(2/0/1) 20(2/0/1) 20(2/0/1) 20(2/0/1) 20(2/0/1) 22(2/0/1) ([d32 ,B],I,d 32 ) 17(2/0/0) 17(2/0/0) 20(2/0/1) 20(2/0/1) 20(2/0/1) 20(2/0/1) 20(2/0/1) 22(2/0/1) 8-20 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. BEST CASE (Continued) Source Freescale Semiconductor, Inc... Address Mode Destination (d8,An,Xn) (d16 ,An,Xn) (B) (d16 ,B) (d32 ,B) ([B],I) ([B],I,d16 ) ([B],I,d32 ) Rn 4(0/0/1) 6(0/0/1) 5(0/0/1) 7(0/0/1) 11(0/0/1) 9(1/0/1) 11(1/0/1) 12(1/0/1) #.B,W 4(0/0/1) 6(0/0/1) 5(0/0/1) 7(0/0/1) 11(0/0/1) 9(1/0/1) 11(1/0/1) 12(1/0/1) #.L 4(0/0/1) 6(0/0/1) 5(0/0/1) 7(0/0/1) 11(0/0/1) 9(1/0/1) 11(1/0/1) 12(1/0/1) (An) 8(1/0/1) 10(1/0/1) 9(1/0/1) 11(1/0/1) 15(1/0/1) 13(2/0/1) 15(2/0/1) 16(2/0/1) (An)+ 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) -(An) 8(1/0/1) 10(1/0/1) 9(1/0/1) 11(1/0/1) 15(1/0/1) 13(2/0/1) 15(2/0/1) 16(2/0/1) (d 16 ,An) or (d 16 ,PC) 8(1/0/1) 10(1/0/1) 9(1/0/1) 11(1/0/1) 15(1/0/1) 13(2/0/1) 15(2/0/1) 16(2/0/1) (xxx).W 8(1/0/1) 10(1/0/1) 9(1/0/1) 11(1/0/1) 15(1/0/1) 13(2/0/1) 15(2/0/1) 16(2/0/1) (xxx).L 8(1/0/1) 10(1/0/1) 9(1/0/1) 11(1/0/1) 15(1/0/1) 13(2/0/1) 15(2/0/1) 16(2/0/1) (d 8,An,Xn) or (d 8,PC,Xn) 9(1/0/1) 10(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (B) 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (d 16 ,B) 11(1/0/1) 13(1/0/1) 12(1/0/1) 14(1/0/1) 18(1/0/1) 16(2/0/1) 18(2/0/1) 19(2/0/1) (d 32 ,B) 15(1/0/1) 17(1/0/1) 18(1/0/1) 18(1/0/1) 22(1/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) ([B],I) 14(2/0/1) 16(2/0/1) 17(2/0/1) 17(2/0/1) 21(2/0/1) 19(3/0/1) 21(3/0/1) 22(3/0/1) ([B],I,d 16 ) 16(2/0/1) 18(2/0/1) 19(2/0/1) 19(2/0/1) 23(2/0/1) 21(3/0/1) 23(3/0/1) 24(3/0/1) ([B],I,d 32 ) 16(2/0/1) 18(2/0/1) 19(2/0/1) 19(2/0/1) 23(2/0/1) 21(3/0/1) 23(3/0/1) 24(3/0/1) ([d16 ,B],I) 16(2/0/1) 18(2/0/1) 19(2/0/1) 19(2/0/1) 23(2/0/1) 21(3/0/1) 23(3/0/1) 24(3/0/1) ([d16 ,B],I,d 16 ) 18(2/0/1) 20(2/0/1) 21(2/0/1) 21(2/0/1) 25(2/0/1) 23(3/0/1) 25(3/0/1) 26(3/0/1) ([d16 ,B],I,d 32 ) 18(2/0/1) 20(2/0/1) 21(2/0/1) 21(2/0/1) 25(2/0/1) 23(3/0/1) 25(3/0/1) 26(3/0/1) ([d32 ,B],I) 20(2/0/1) 22(2/0/1) 23(2/0/1) 23(2/0/1) 27(2/0/1) 25(3/0/1) 27(3/0/1) 28(3/0/1) ([d32 ,B],I,d 16 ) 22(2/0/1) 24(2/0/1) 25(2/0/1) 25(2/0/1) 29(2/0/1) 27(3/0/1) 29(3/0/1) 30(3/0/1) ([d32 ,B],I,d 32 ) 22(2/0/1) 24(2/0/1) 25(2/0/1) 25(2/0/1) 29(2/0/1) 27(3/0/1) 29(3/0/1) 30(3/0/1) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-21 Freescale Semiconductor, Inc. BEST CASE (Concluded) Source Freescale Semiconductor, Inc... Address Mode Destination ([d16 ,B],I) ([d16 ,B],I,d 16) ([d16 ,B],I,d 32 ) ([d32 ,B],I) ([d32 ,B],I,d 16 ) ([d32 ,B],I,d 32 ) Rn 11(1/0/1) 13(1/0/1) 14(1/0/1) 15(1/0/1) 17(1/0/1) 18(1/0/1) #.B,W 11(1/0/1) 13(1/0/1) 14(1/0/1) 15(1/0/1) 17(1/0/1) 18(1/0/1) #.L 11(1/0/1) 13(1/0/1) 14(1/0/1) 15(1/0/1) 17(1/0/1) 18(1/0/1) (An) 15(2/0/1) 17(2/0/1) 18(2/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (An)+ 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) -(An) 15(2/0/1) 17(2/0/1) 18(2/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (d 16 ,An) or (d16 ,PC) 15(2/0/1) 17(2/0/1) 18(2/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (xxx).W 15(2/0/1) 17(2/0/1) 18(2/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (xxx).L 15(2/0/1) 17(2/0/1) 18(2/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (d 8,An,Xn) or (d 8,PC,Xn) 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (B) 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (d 16 ,B) 18(2/0/1) 20(2/0/1) 21(2/0/1) 22(2/0/1) 24(2/0/1) 25(2/0/1) (d 32 ,B) 22(2/0/1) 24(2/0/1) 25(2/0/1) 26(2/0/1) 28(2/0/1) 29(2/0/1) ([B],I) 21(3/0/1) 23(3/0/1) 24(3/0/1) 25(3/0/1) 27(3/0/1) 28(3/0/1) ([B],I,d 16 ) 23(3/0/1) 25(3/0/1) 26(3/0/1) 27(3/0/1) 29(3/0/1) 30(3/0/1) ([B],I,d 32 ) 23(3/0/1) 25(3/0/1) 26(3/0/1) 27(3/0/1) 29(3/0/1) 30(3/0/1) ([d16 ,B],I) 23(3/0/1) 25(3/0/1) 26(3/0/1) 27(3/0/1) 29(3/0/1) 30(3/0/1) ([d16 ,B],I,d 16 ) 25(3/0/1) 27(3/0/1) 28(3/0/1) 29(3/0/1) 31(3/0/1) 32(3/0/1) ([d16 ,B],I,d 32 ) 25(3/0/1) 27(3/0/1) 28(3/0/1) 29(3/0/1) 31(3/0/1) 32(0/0/1) ([d32 ,B],I) 27(3/0/1) 29(3/0/1) 30(3/0/1) 31(3/0/1) 33(3/0/1) 34(3/0/1) ([d32 ,B],I,d 16 ) 29(3/0/1) 31(3/0/1) 32(3/0/1) 33(3/0/1) 35(3/0/1) 36(3/0/1) ([d32 ,B],I,d 32 ) 29(3/0/1) 31(3/0/1) 32(3/0/1) 33(3/0/1) 35(3/0/1) 36(3/0/1) 8-22 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. CACHE CASE Source Freescale Semiconductor, Inc... Address Mode Destination An Dn (An) (An)+ -(An) (d16 ,An) (xxx).W (xxx).L Rn 2(0/0/0) 2(0/0/0) 4(0/0/1) 4(0/0/1) 5(0/0/1) 5(0/0/1) 4(0/0/1) 6(0/0/1) #.B,W 4(0/0/0) 4(0/0/0) 6(0/0/1) 6(0/0/1) 7(0/0/1) 7(0/0/1) 6(0/0/1) 8(0/0/1) #.L 6(0/0/0) 6(0/0/0) 8(0/0/1) 8(0/0/1) 9(0/0/1) 9(0/0/1) 8(0/0/1) 10(0/0/1) (An) 6(1/0/0) 6(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (An)+ 6(1/0/0) 6(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) -(An) 7(1/0/0) 7(1/0/0) 8(1/0/1) 8(1/0/1) 8(1/0/1) 8(1/0/1) 8(1/0/1) 10(1/0/1) (d 16 ,An) or (d 16 ,PC) 7(1/0/0) 7(1/0/0) 8(1/0/1) 8(1/0/1) 8(1/0/1) 8(1/0/1) 8(1/0/1) 10(1/0/1) (xxx).W 6(1/0/0) 6(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (xxx).L 6(1/0/0) 6(1/0/0) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 7(1/0/1) 9(1/0/1) (d 8,An,Xn) or (d 8,PC,Xn) 9(1/0/0) 9(1/0/0) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 12(1/0/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 9(1/0/0) 9(1/0/0) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 12(1/0/1) (B) 9(1/0/0) 9(1/0/0) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 10(1/0/1) 12(1/0/1) (d 16 ,B) 11(1/0/0) 11(1/0/0) 12(1/0/1) 12(1/0/1) 12(1/0/1) 12(1/0/1) 12(1/0/1) 14(1/0/1) (d 32 ,B) 15(1/0/0) 15(1/0/0) 16(1/0/1) 16(1/0/1) 16(1/0/1) 16(1/0/1) 16(1/0/1) 18(1/0/1) ([B],I) 14(2/0/0) 14(2/0/0) 15(2/0/1) 15(2/0/1) 15(2/0/1) 15(2/0/1) 15(2/0/1) 17(2/0/1) ([B],I,d 16 ) 16(2/0/0) 16(2/0/0) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 19(2/0/1) ([B],I,d 32 ) 16(2/0/0) 16(2/0/0) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 19(2/0/1) ([d16 ,B],I) 16(2/0/0) 16(2/0/0) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 17(2/0/1) 19(2/0/1) ([d16 ,B],I,d 16 ) 18(2/0/0) 18(2/0/0) 19(2/0/1) 19(2/0/1) 19(2/0/1) 19(2/0/1) 19(2/0/1) 21(2/0/1) ([d16 ,B],d 32 ) 18(2/0/0) 18(2/0/0) 19(2/0/1) 19(2/0/1) 19(2/0/1) 19(2/0/1) 19(2/0/1) 21(2/0/1) ([d32 ,B],I) 20(2/0/0) 20(2/0/0) 21(2/0/1) 21(2/0/1) 21(2/0/1) 21(2/0/1) 21(2/0/1) 23(2/0/1) ([d32 ,B],I,d 16 ) 22(2/0/0) 22(2/0/0) 23(2/0/1) 23(2/0/1) 23(2/0/1) 23(2/0/1) 23(2/0/1) 25(2/0/1) ([d32 ,B],I,d 32 ) 22(2/0/0) 22(2/0/0) 23(2/0/1) 23(2/0/1) 23(2/0/1) 23(2/0/1) 23(2/0/1) 25(2/0/1) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-23 Freescale Semiconductor, Inc. CACHE CASE (Continued) Source Freescale Semiconductor, Inc... Address Mode Destination (d8,An,Xn) (d16 ,An,Xn) (B) Rn 7(0/0/1) 9(0/0/1) 8(0/0/1) #.B,W 7(0/0/1) 9(0/0/1) 8(0/0/1) #.L 9(0/0/1) (An) ([B],I,d16 ) ([B],I,d32 ) 10(0/0/1) 14(0/0/1) 12(1/0/1) 14(1/0/1) 15(1/0/1) 10(0/0/1) 14(0/0/1) 12(1/0/1) 14(1/0/1) 15(1/0/1) 11(0/0/1) 10(0/0/1) 12(0/0/1) 16(0/0/1) 14(1/0/1) 16(1/0/1) 17(1/0/1) 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (An)+ 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) -(An) 10(1/0/1) 12(1/0/1) 11(1/0/1) 13(1/0/1) 17(1/0/1) 15(2/0/1) 17(2/0/1) 18(2/0/1) (d 16 ,An) or (d 16 ,PC) 10(1/0/1) 12(2/0/1) 11(1/0/1) 13(1/0/1) 17(1/0/1) 15(2/0/1) 17(2/0/1) 18(2/0/1) (xxx).W 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (xxx).L 9(1/0/1) 11(1/0/1) 10(1/0/1) 12(1/0/1) 16(1/0/1) 14(2/0/1) 16(2/0/1) 17(2/0/1) (d 8,An,Xn) or (d 8,PC,Xn) 12(1/0/1) 14(1/0/1) 13(1/0/1) 15(1/0/1) 19(1/0/1) 17(2/0/1) 19(2/0/1) 20(2/0/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 12(1/0/1) 14(1/0/1) 13(1/0/1) 15(1/0/1) 19(1/0/1) 17(2/0/1) 19(2/0/1) 20(2/0/1) (B) 12(1/0/1) 14(1/0/1) 13(1/0/1) 15(1/0/1) 19(1/0/1) 17(2/0/1) 19(2/0/1) 20(2/0/1) (d 16 ,B) 14(1/0/1) 16(1/0/1) 15(1/0/1) 17(1/0/1) 21(1/0/1) 19(2/0/1) 21(2/0/1) 22(2/0/1) (d 32 ,B) 18(1/0/1) 20(1/0/1) 19(1/0/1) 21(1/0/1) 25(1/0/1) 23(2/0/1) 25(2/0/1) 26(2/0/1) ([B],I) 17(2/0/1) 19(2/0/1) 18(2/0/1) 20(2/0/1) 24(2/0/1) 22(3/0/1) 24(3/0/1) 25(3/0/1) ([B],I,d 16 ) 19(2/0/1) 21(2/0/1) 20(2/0/1) 22(2/0/1) 26(2/0/1) 24(3/0/1) 26(3/0/1) 27(3/0/1) ([B],I,d 32 ) 19(2/0/1) 21(2/0/1) 20(2/0/1) 22(2/0/1) 26(2/0/1) 24(3/0/1) 26(3/0/1) 27(3/0/1) ([d16 ,B],I) 19(2/0/1) 21(2/0/1) 20(2/0/1) 22(2/0/1) 26(2/0/1) 24(3/0/1) 26(3/0/1) 27(3/0/1) ([d16 ,B],I,d 16 ) 21(2/0/1) 23(2/0/1) 22(2/0/1) 24(2/0/1) 28(2/0/1) 26(3/0/1) 28(3/0/1) 29(3/0/1) ([d16 ,B],I,d 32 ) 21(2/0/1) 23(2/0/1) 22(2/0/1) 24(2/0/1) 28(2/0/1) 26(3/0/1) 28(3/0/1) 29(3/0/1) ([d32 ,B],I) 23(2/0/1) 25(2/0/1) 24(2/0/1) 26(2/0/1) 30(2/0/1) 28(3/0/1) 30(3/0/1) 31(3/0/1) ([d32 ,B],I,d 16 ) 25(2/0/1) 27(2/0/1) 26(2/0/1) 28(2/0/1) 32(2/0/1) 30(3/0/1) 32(3/0/1) 33(3/0/1) ([d32 ,B],I,d 32 ) 25(2/0/1) 27(2/0/1) 26(2/0/1) 28(2/0/1) 32(2/0/1) 30(3/0/1) 32(3/0/1) 33(3/0/1) 8-24 (d16 ,B) (d32 ,B) ([B],I) M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. CACHE CASE (Concluded) Source Freescale Semiconductor, Inc... Address Mode Destination ([d16 ,B],I) ([d16 ,B],I,d 16 ) ([d16 ,B],I,d 32 ) ([d32 ,B],I) ([d32 ,B],I,d 16 ) ([d32 ,B],I,d 32 ) Rn 14(1/0/1) 16(1/0/1) 17(1/0/1) 18(1/0/1) 20(1/0/1) 21(1/0/1) #.B,W 14(1/0/1) 16(1/0/1) 17(1/0/1) 18(1/0/1) 20(1/0/1) 21(1/0/1) #.L 16(1/0/1) 18(1/0/1) 19(1/0/1) 20(1/0/1) 22(1/0/1) 23(1/0/1) (An) 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (An)+ 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) -(An) 17(2/0/1) 19(2/0/1) 20(2/0/1) 21(2/0/1) 23(2/0/1) 24(2/0/1) (d 16 ,An) or (d16 ,PC) 17(2/0/1) 19(2/0/1) 20(2/0/1) 21(2/0/1) 23(2/0/1) 24(2/0/1) (xxx).W 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (xxx).L 16(2/0/1) 18(2/0/1) 19(2/0/1) 20(2/0/1) 22(2/0/1) 23(2/0/1) (d 8,An,Xn) or (d 8,PC,Xn) 19(2/0/1) 21(2/0/1) 22(2/0/1) 23(2/0/1) 25(2/0/1) 26(2/0/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 19(2/0/1) 21(2/0/1) 22(2/0/1) 23(2/0/1) 25(2/0/1) 26(2/0/1) (B) 19(2/0/1) 21(2/0/1) 22(2/0/1) 23(2/0/1) 25(2/0/1) 26(2/0/1) (d 16 ,B) 21(2/0/1) 23(2/0/1) 24(2/0/1) 25(2/0/1) 27(2/0/1) 28(2/0/1) (d 32 ,B) 25(2/0/1) 27(2/0/1) 28(2/0/1) 29(2/0/1) 31(2/0/1) 32(2/0/1) ([B],I) 24(3/0/1) 26(3/0/1) 27(3/0/1) 28(3/0/1) 30(3/0/1) 31(3/0/1) ([B],I,d 16 ) 26(3/0/1) 28(3/0/1) 29(3/0/1) 30(3/0/1) 32(3/0/1) 33(3/0/1) ([B],I,d 32 ) 26(3/0/1) 28(3/0/1) 29(3/0/1) 30(3/0/1) 32(3/0/1) 33(3/0/1) ([d16 ,B],I) 26(3/0/1) 28(3/0/1) 29(3/0/1) 30(3/0/1) 32(3/0/1) 33(3/0/1) ([d16 ,B],I,d 16 ) 28(3/0/1) 30(3/0/1) 31(3/0/1) 32(3/0/1) 34(3/0/1) 35(3/0/1) ([d16 ,B],I,d 32 ) 28(3/0/1) 30(3/0/1) 31(3/0/1) 32(3/0/1) 34(3/0/1) 35(3/0/1) ([d32 ,B],I) 30(3/0/1) 32(3/0/1) 33(3/0/1) 34(3/0/1) 36(3/0/1) 37(3/0/1) ([d32 ,B],I,d 16 ) 32(3/0/1) 34(3/0/1) 35(3/0/1) 36(3/0/1) 38(3/0/1) 39(3/0/1) ([d32 ,B],I,d 32 ) 32(3/0/1) 34(3/0/1) 35(3/0/1) 36(3/0/1) 38(3/0/1) 39(3/0/1) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-25 Freescale Semiconductor, Inc. WORST CASE Destination Freescale Semiconductor, Inc... Source Address Mode An Dn (An) (An)+ -(An) (d16 ,An) (xxx).W (xxx).L Rn 3(0/1/0) 3(0/1/0) 5(0/1/0) 5(0/1/1) 6(0/1/1) 7(0/1/1) 7(0/1/1) 9(0/2/1) #.B,W 3(0/1/0) 3(0/1/0) 5(0/1/0) 8(0/1/1) 6(0/1/1) 7(0/1/1) 7(0/1/1) 9(0/2/1) #.L 5(0/1/0) 5(0/1/0) 7(0/0/1) 7(0/1/1) 8(0/1/1) 9(0/1/1) 9(0/1/1) 11(0/2/1) (An) 7(1/1/0) 7(1/1/0) 9(1/1/1) 9(1/1/1) 9(1/1/1) 11(1/1/1) 11(1/1/1) 13(1/2/1) (An)+ 7(1/1/0) 7(1/1/0) 9(1/1/1) 9(1/1/1) 9(1/1/1) 11(1/1/1) 11(1/1/1) 13(1/2/1) -(An) 8(1/1/0) 8(1/1/0) 10(1/1/1) 10(1/1/1) 10(1/1/1) 12(1/1/1) 12(1/1/1) 14(1/2/1) (d 16 ,An) or (d16 ,PC) 9(1/2/0) 9(1/2/0) 11(1/2/1) 11(1/2/1) 11(1/2/1) 13(1/2/1) 13(1/2/1) 15(1/3/1) (xxx).W 8(1/2/0) 8(1/2/0) 10(1/2/1) 10(1/2/1) 10(1/2/1) 12(1/2/1) 12(1/2/1) 14(1/3/1) (xxx).L 10(1/2/0) 10(1/2/0) 12(1/2/1) 12(1/2/1) 12(1/2/1) 14(1/2/1) 14(1/2/1) 16(1/3/1) (d 8,An,Xn) or (d8,PC,Xn) 11(1/2/0) 11(1/2/0) 13(1/2/1) 13(1/2/1) 13(1/2/1) 15(1/2/1) 15(1/2/1) 17(1/3/1) (d 16 ,An,Xn) or (d16 ,PC,Xn) 12(1/2/0) 12(1/2/0) 14(1/2/1) 14(1/2/1) 14(1/2/1) 16(1/2/1) 16(1/2/1) 18(1/3/1) (B) 12(1/2/0) 12(1/2/0) 14(1/2/1) 14(1/2/1) 14(1/2/1) 16(1/2/1) 16(1/2/1) 18(1/3/1) (d 16 ,B) 15(1/2/0) 15(1/2/0) 17(1/2/1) 17(1/2/1) 17(1/3/1) 19(1/2/1) 19(1/2/1) 21(1/3/1) (d 32 ,B) 19(1/3/0) 19(1/3/0) 21(1/3/1) 21(1/3/1) 21(1/3/1) 23(1/3/1) 23(1/3/1) 25(1/4/1) ([B],I) 16(2/2/0) 16(2/2/0) 18(2/2/1) 18(2/2/1) 18(2/2/1) 20(2/2/1) 20(2/2/1) 22(2/3/1) ([B],I,d 16 ) 19(2/2/0) 19(2/2/0) 21(2/2/1) 21(2/2/1) 21(2/2/1) 23(2/2/1) 23(2/2/1) 25(2/3/1) ([B],I,d 32 ) 20(2/3/0) 20(2/3/0) 22(2/3/1) 22(2/3/1) 22(2/3/1) 24(2/3/1) 24(2/3/1) 26(2/4/1) ([d16 ,B],I) 19(2/2/0) 19(2/2/0) 21(2/2/1) 21(2/2/1) 21(2/2/1) 23(2/2/1) 23(2/2/1) 25(2/3/1) ([d16 ,B],I,d 16 ) 22(2/3/0) 22(2/3/0) 24(2/3/1) 24(2/3/1) 24(2/3/1) 26(2/3/1) 26(2/3/1) 28(2/4/1) ([d16 ,B],d 32 ) 23(2/3/0) 23(2/3/0) 25(2/3/1) 25(2/3/1) 25(2/3/1) 27(2/3/1) 27(2/3/1) 29(2/4/1) ([d32 ,B],I) 23(2/3/0) 23(2/3/0) 25(2/3/1) 25(2/3/1) 25(2/3/1) 27(2/3/1) 27(2/3/1) 29(2/4/1) ([d32 ,B],I,d 16 ) 25(2/3/0) 25(2/3/0) 27(2/3/1) 27(2/3/1) 27(2/3/1) 29(2/3/1) 29(2/3/1) 31(2/4/1) ([d32 ,B],I,d 32 ) 27(2/4/0) 27(2/4/0) 29(2/4/1) 29(2/4/1) 29(2/4/1) 31(2/4/1) 31(2/4/1) 33(2/5/1) 8-26 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. WORST CASE (Continued) Source Address Mode Rn Freescale Semiconductor, Inc... #.B,W Destination (d8,An,Xn) (d16,An,Xn) 9(0/1/1) 12(0/2/1) (B) (d16,B) (d32,B) ([B],I) 10(0/1/1) 14(0/2/1) 19(0/2/1) 14(1/1/1) ([B],I,d16) 17(1/2/1) ([B],I,D32) 20(1/2/1) 9(0/1/1) 12(0/2/1) 10(0/1/1) 14(0/2/1) 19(0/2/1) 14(1/1/1) 17(1/2/1) 20(1/2/1) #.L 11(0/1/1) 14(0/2/1) 12(0/1/1) 16(0/2/1) 21(0/2/1) 16(1/1/1) 19(1/2/1) 22(1/2/1) (An) 11(1/1/1) 14(1/2/1) 12(1/1/1) 16(1/2/1) 21(1/2/1) 12(2/1/1) 19(2/2/1) 22(2/2/1) (An)+ 11(1/1/1) 14(1/2/1) 12(1/1/1) 16(1/2/1) 21(1/2/1) 12(2/1/1) 19(2/2/1) 22(2/2/1) -(An) 12(1/1/1) 15(1/2/1) 13(1/1/1) 17(1/2/1) 22(1/2/1) 13(2/1/1) 20(2/2/1) 23(2/2/1) (d 16 ,An) or (d 16 ,PC) 13(1/2/1) 16(1/3/1) 14(1/2/1) 18(1/3/1) 23(1/3/1) 14(2/2/1) 21(2/3/1) 24(2/3/1) (xxx).W 12(1/2/1) 15(1/3/1) 13(1/2/1) 17(1/3/1) 22(1/3/1) 13(2/2/1) 20(2/3/1) 23(2/3/1) (xxx).L 14(1/2/1) 17(1/3/1) 15(1/2/1) 19(1/3/1) 24(1/3/1) 15(2/2/1) 22(2/3/1) 25(2/3/1) (d 8,An,Xn) or (d 8,PC,Xn) 15(1/2/1) 18(1/3/1) 16(1/2/1) 20(1/3/1) 25(1/3/1) 16(2/2/1) 23(2/3/1) 26(2/3/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 16(1/2/1) 19(1/3/1) 17(1/2/1) 21(1/3/1) 26(1/3/1) 17(2/2/1) 24(2/3/1) 27(2/3/1) (B) 16(1/2/1) 19(1/3/1) 17(1/2/1) 21(1/3/1) 26(1/3/1) 17(2/2/1) 24(2/3/1) 27(2/3/1) (d 16 ,B) 19(1/2/1) 22(1/3/1) 20(1/2/1) 24(1/3/1) 29(1/3/1) 20(2/2/1) 27(2/3/1) 30(2/3/1) (d 32 ,B) 23(1/3/1) 26(1/4/1) 24(1/3/1) 28(1/4/1) 33(1/4/1) 24(2/3/1) 31(2/4/1) 34(2/4/1) ([B],I) 20(2/2/1) 23(2/3/1) 21(2/2/1) 25(2/3/1) 30(2/3/1) 21(3/2/1) 28(3/3/1) 31(3/3/1) ([B],I,d 16 ) 23(2/2/1) 26(2/3/1) 24(2/2/1) 28(2/3/1) 33(2/3/1) 24(3/2/1) 31(3/3/1) 34(3/3/1) ([B],I,d 32 ) 24(2/3/1) 27(2/4/1) 25(2/3/1) 29(2/4/1) 34(2/4/1) 25(3/3/1) 32(3/4/1) 35(3/4/1) ([d16 ,B],I) 23(2/2/1) 26(2/3/1) 24(2/2/1) 28(2/3/1) 33(2/3/1) 24(3/2/1) 31(3/3/1) 34(3/3/1) ([d16 ,B],I,d 16 ) 26(2/3/1) 29(2/4/1) 27(2/3/1) 31(2/4/1) 36(2/4/1) 27(3/3/1) 34(3/4/1) 37(3/4/1) ([d16 ,B],I,d 32 ) 27(2/3/1) 30(2/4/1) 28(2/3/1) 32(2/4/1) 37(2/4/1) 28(3/3/1) 35(3/4/1) 38(3/4/1) ([d32 ,B],I) 27(2/3/1) 30(2/4/1) 28(2/3/1) 32(2/4/1) 37(2/4/1) 28(3/3/1) 35(3/4/1) 38(3/4/1) ([d32 ,B],I,d 16 ) 29(2/3/1) 32(2/4/1) 30(2/3/1) 34(2/4/1) 39(2/4/1) 30(3/3/1) 37(3/4/1) 40(3/4/1) ([d32 ,B],I,d 32 ) 31(2/4/1) 34(2/5/1) 32(2/4/1) 36(2/5/1) 41(2/5/1) 32(3/4/1) 39(3/5/1) 42(3/5/1) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-27 Freescale Semiconductor, Inc. WORST CASE (Concluded) Source Address Mode ([d16,B],I) 17(1/2/1) ([d16,B],I,d16) 20(1/2/1) ([d16,B],I,d 32) 23(1/3/1) ([d32,B],I) 22(1/2/1) ([d32,B],I,d 16) 25(1/3/1) ([d32,B],I,d 32) 27(1/3/1) #.B,W 17(1/2/1) 20(1/2/1) 23(1/3/1) 22(1/2/1) 25(1/3/1) 27(1/3/1) #.L 19(1/2/1) 22(1/2/1) 25(1/3/1) 24(1/2/1) 27(1/3/1) 29(1/3/1) (An) 19(2/2/1) 22(2/2/1) 25(2/3/1) 24(2/2/1) 27(2/3/1) 29(2/3/1) (An)+ 19(2/2/1) 22(2/2/1) 25(2/3/1) 24(2/2/1) 27(2/3/1) 29(2/3/1) -(An) 20(2/2/1) 23(2/2/1) 26(2/3/1) 25(2/2/1) 28(2/3/1) 30(2/3/1) (d 16 ,An) or (d16 ,PC) 21(2/3/1) 24(2/3/1) 27(2/4/1) 26(2/3/1) 29(2/4/1) 31(2/4/1) (xxx).W 20(2/3/1) 23(2/3/1) 26(2/4/1) 27(2/3/1) 28(2/4/1) 30(2/4/1) (xxx).L 22(2/3/1) 25(2/3/1) 28(2/4/1) 29(2/3/1) 30(2/4/1) 32(2/4/1) (d 8,An,Xn) or (d 8,PC,Xn) 23(2/3/1) 26(2/3/1) 29(2/4/1) 30(2/3/1) 31(2/4/1) 33(2/4/1) (d 16 ,An,Xn) or (d 16 ,PC,Xn) 24(2/3/1) 27(2/3/1) 30(2/4/1) 31(2/3/1) 32(2/4/1) 34(2/4/1) (B) 24(2/3/1) 27(2/3/1) 30(2/4/1) 31(2/3/1) 32(2/4/1) 34(2/4/1) (d 16 ,B) 27(2/3/1) 30(2/3/1) 33(2/4/1) 34(2/3/1) 35(2/4/1) 37(2/4/1) (d 32 ,B) 31(2/4/1) 34(2/4/1) 37(2/5/1) 38(2/4/1) 39(2/5/1) 41(2/5/1) ([B],I) 28(3/3/1) 31(3/3/1) 34(3/4/1) 35(3/3/1) 36(3/4/1) 38(3/4/1) ([B],I,d 16 ) 31(3/3/1) 34(3/3/1) 37(3/4/1) 38(3/3/1) 39(3/4/1) 41(3/4/1) ([B],I,d 32 ) 32(3/4/1) 35(3/4/1) 38(3/5/1) 39(3/4/1) 40(3/5/1) 42(3/5/1) ([d16 ,B],I) 31(3/3/1) 34(3/3/1) 37(3/4/1) 38(3/3/1) 39(3/4/1) 41(3/4/1) ([d16 ,B],I,d 16 ) 34(3/4/1) 37(3/4/1) 40(3/5/1) 41(3/4/1) 42(3/5/1) 44(3/5/1) ([d16 ,B],I,d 32 ) 35(3/4/1) 38(3/4/1) 41(3/5/1) 42(3/4/1) 43(3/5/1) 45(3/5/1) ([d32 ,B],I) 35(3/4/1) 38(3/4/1) 41(3/5/1) 42(3/4/1) 43(3/5/1) 45(3/5/1) ([d32 ,B],I,d 16 ) 37(3/4/1) 40(3/4/1) 43(3/5/1) 44(3/4/1) 45(3/5/1) 47(3/5/1) ([d32 ,B],I,d 32 ) 39(3/5/1) 42(3/5/1) 45(3/6/1) 46(3/5/1) 47(3/6/1) 49(3/6/1) Rn Freescale Semiconductor, Inc... Destination 8-28 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.7 Special-Purpose MOVE Instruction The special-purpose MOVE instruction table indicates the number of clock periods needed for the processor to fetch, calculate, and perform the special-purpose MOVE operation on the control registers or specified effective address. The total number of clock cycles is outside the parentheses, the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case EXG Ry,Rx 0(0/0/0) 2(0/0/0) 3(0/1/0) MOVEC Cr,Rn 3(0/0/0) 6(0/0/0) 7(0/1/0) MOVEC Rn,Cr 9(0/0/0) 12(0/0/0) 13(0/1/0) MOVE PSW,Rn 1(0/0/0) 4(0/0/0) 5(0/1/0) MOVE PSW,Mem 5(0/0/1) 5(0/0/1) 7(0/1/1) * MOVE EA,CCR 4(0/0/0) 4(0/0/0) 5(0/1/0) * MOVE EA,SR 8(0/0/0) 8(0/0/0) 11(0/2/0) MOVEM EA,RL 8 + 4n (n/0/0) 8 + 4n (n/0/0) 9 + 4n (n/1/0) MOVEM RL,EA 4 + 3n (0/0/n) 4 + 3n (0/0/n) 5 + 3n (0/1/n) MOVEP.W Dn,(d 16 ,An) 8(0/0/2) 11(0/0/2) 11(0/1/2) MOVEP.L Dn,(d 16 ,An) 14(0/0/4) 17(0/0/4) 17(0/1/4) MOVEP.W (d 16 ,An),Dn 10(2/0/0) 12(2/0/0) 12(2/1/0) MOVEP.L (d 16 ,An),Dn 16(4/0/0) 18(4/0/0) 18(4/1/0) MOVES EA,Rn 7(1/0/0) 7(1/0/0) 8(1/1/0) MOVES Rn,EA 5(0/0/1) 5(0/0/1) 7(0/1/1) MOVE USP 0(0/0/0) 2(0/0/0) 3(0/1/0) SWAP Rx,Ry 1(0/0/0) 4(0/0/0) 4(0/1/0) n--Number of Registers to Transfer RL--Register List *Add Fetch Effective Address Time Add Calculate Effective Address Time Add Calculate Immediate Address Time MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-29 Freescale Semiconductor, Inc. 8.2.8 Arithmetic/Logical Instructions The arithmetic/logical instructions table indicates the number of clock periods needed for the processor to perform the specified arithmetic/logical operation using the specified addressing mode. It also includes, in worst case, the amount of time needed to prefetch the next instruction. Footnotes specify when to add either fetch address or fetch immediate effective address time. This sum gives the total effective execution time for the operation using the specified addressing mode. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case * ADD EA,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * ADDA EA,An 0(0/0/0) 2(0/0/0) 3(0/1/0) * ADD Dn,EA 3(0/0/1) 4(0/0/1) 6(0/1/1) * AND EA,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * AND Dn,EA 3(0/0/1) 4(0/0/1) 6(0/1/1) * EOR Dn,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * EOR Dn,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) * OR EA,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * OR Dn,EA 3(0/0/1) 4(0/0/1) 6(0/1/1) * SUB EA,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * SUBA EA,An 0(0/0/0) 2(0/0/0) 3(0/1/0) * SUB Dn,EA 3(0/0/1) 4(0/0/1) 6(0/1/1) * CMP EA,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) * CMPA EA,An 1(0/0/0) 4(0/0/0) 4(0/1/0) ** CMP2 EA,Rn 16(1/0/0) 18(1/0/0) 18(1/1/0) * MUL.W EA,Dn 25(0/0/0) 27(0/0/0) 28(0/1/0) ** MUL.L EA,Dn 41(0/0/0) 43(0/0/0) 44(0/1/0) * DIVU.W EA,Dn 42(0/0/0) 44(0/0/0) 44(0/1/0) ** DIVU.L EA,Dn 76(0/0/0) 78(0/0/0) 79(0/1/0) * DIVS.W EA,Dn 54(0/0/0) 56(0/0/0) 57(0/1/0) ** DIVS.L EA,Dn 88(0/0/0) 90(0/0/0) 91(0/1/0) *Add Fetch Effective Address Time ** Add Fetch Immediate Address Time 8-30 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.9 Immediate Arithmetic/Logical Instructions The immediate arithmetic/logical instructions table indicates the number of clock periods needed for the processor to fetch the source immediate data value and perform the specified arithmetic/logical operation using the specified destination addressing mode. Footnotes indicate when to add appropriate fetch effective or fetch immediate effective address time. This computation will give the total execution time needed to perform the appropriate immediate arithmetic/logical operation. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case MOVEQ #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ADDQ #,Rn 0(0/0/0) 2(0/0/0) 3(0/1/0) ADDQ #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) SUBQ #,Rn 0(0/0/0) 2(0/0/0) 3(0/1/0) * SUBQ #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** ADDI #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ** ADDI #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** ANDI #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ** ANDI #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** EORI #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ** EORI #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** ORI #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ** ORI #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** SUBI #,Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) ** SUBI #,Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) ** CMPI #,EA 0(0/0/0) 2(0/0/0) 3(0/1/0) * *Add Fetch Effective Address Time ** Add Fetch Immediate Address Time MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-31 Freescale Semiconductor, Inc. 8.2.10 Binary-Coded Decimal Operations Freescale Semiconductor, Inc... The binary-coded decimal operations table indicates the number of clock periods needed for the processor to perform the specified operation using the given addressing modes, with complete execution times given. No additional tables are needed to calculate total effective execution time for these instructions. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Instruction Best Case Cache Case Worst Case ABCD Dn,Dn 4(0/0/0) 4(0/0/0) 5(0/1/0) ABCD -(An),-(An) 14(2/0/1) 16(2/0/1) 17(2/1/1) SBCD Dn,Dn 4(0/0/0) 4(0/0/0) 5(0/1/0) SBCD -(An),-(An) 14(2/0/1) 16(2/0/1) 17(2/1/1) ADDX Dn,Dn 2(0/0/0) 2(0/0/0) 3(0/1/0) ADDX -(An),-(An) 10(2/0/1) 12(2/0/1) 13(2/1/1) SUBX Dn,Dn 2(0/0/0) 2(0/0/0) 3(0/1/0) SUBX -(An),-(An) 10(2/0/1) 12(2/0/1) 13(2/1/1) CMPM (An)+,(An)+ 8(2/0/0) 9(2/0/0) 10(2/1/0) PACK Dn,Dn,# 3(0/0/0) 6(0/0/0) 7(0/1/0) PACK -(An),-(An),# 11(1/0/1) 13(1/0/1) 13(1/1/1) UNPK Dn,Dn,# 5(0/0/0) 8(0/0/0) 9(0/1/0) UNPK -(An),-(An),# 11(1/0/1) 13(1/0/1) 13(1/1/1) 8-32 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.11 Single-Operand Instructions The single-operand instructions table indicates the number of clock periods needed for the processor to perform the specified operation on the given addressing mode. Footnotes indicate when it is necessary to add another table entry to calculate the total effective execution time for the instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Instruction Cache Case Worst Case CLR Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) CLR Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) NEG Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) NEG Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) NEGX Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) NEGX Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) NOT Dn 0(0/0/0) 2(0/0/0) 3(0/1/0) NOT Mem 3(0/0/1) 4(0/0/1) 6(0/1/1) EXT Dn 1(0/0/0) 4(0/0/0) 4(0/1/0) NBCD Dn 6(0/0/0) 6(0/0/0) 6(0/1/0) Scc Dn 1(0/0/0) 4(0/0/0) 4(0/1/0) Scc Mem 6(0/0/1) 6(0/0/1) 6(0/1/1) TAS Dn 1(0/0/0) 4(0/0/0) 4(0/1/0) TAS Mem 12(1/0/1) 12(1/0/1) 13(1/1/1) * TST EA 0(0/0/0) 2(0/0/0) 3(0/1/0) Freescale Semiconductor, Inc... Best Case * * * *Add Fetch Effective Address Time Add Calculate Effective Address Time MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-33 Freescale Semiconductor, Inc. 8.2.12 Shift/Rotate Instructions The shift/rotate instructions table indicates the number of clock periods needed for the processor to perform the specified operation on the given addressing mode. Footnotes indicate when it is necessary to add another table entry to calculate the total effective execution time for the instruction. The number of bits shifted does not affect execution time. The total number of clock cycles is outside the parentheses, the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case LSL Dn (Static) 1(0/0/0) 4(0/0/0) 4(0/1/0) LSR Dn (Static) 1(0/0/0) 4(0/0/0) 4(0/1/0) LSL Dn (Dynamic) 3(0/0/0) 6(0/0/0) 6(0/1/0) LSR Dn (Dynamic) 3(0/0/0) 6(0/0/0) 6(0/1/0) * LSL Mem by 1 5(0/0/1) 5(0/0/1) 6(0/1/1) * LSR Mem by 1 5(0/0/1) 5(0/0/1) 6(0/1/1) ASL Dn 5(0/0/0) 8(0/0/0) 8(0/1/0) ASR Dn 3(0/0/0) 6(0/0/0) 6(0/1/0) * ASL Mem by 1 6(0/0/1) 6(0/0/1) 7(0/1/1) * ASR Mem by 1 5(0/0/1) 5(0/0/1) 6(0/1/1) ROL Dn 5(0/0/0) 8(0/0/0) 8(0/1/0) ROR Dn 5(0/0/0) 8(0/0/0) 8(0/1/0) * ROL Mem by 1 7(0/0/1) 7(0/0/1) 7(0/1/1) * ROR Mem by 1 7(0/0/1) 7(0/0/1) 7(0/1/1) ROXL Dn 9(0/0/0) 12(0/0/0) 12(0/1/0) ROXR Dn 9(0/0/0) 12(0/0/0) 12(0/1/0) ROXd Mem by 1 5(0/0/1) 5(0/0/1) 6(0/1/1) * *Add Fetch Effective Address Time d--Direction of Shift/Rotate, L or R 8-34 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.13 Bit Manipulation Instructions The bit manipulation instructions table indicates the number of clock periods needed for the processor to perform the specified bit operation on the given addressing mode. Footnotes indicate when it is necessary to add another table entry to calculate the total effective execution time for the instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case BTST #,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) BTST Dn,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) ** BTST #,Mem 4(0/0/0) 4(0/0/0) 5(0/1/0) * BTST Dn,Mem 4(0/0/0) 4(0/0/0) 5(0/1/0) BCHG #,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) BCHG Dn,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) ** BCHG #,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) * BCHG Dn,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) BCLR #,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) BCLR Dn,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) ** BCLR #,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) * BCLR Dn,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) BSET #,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) BSET Dn,Dn 1(0/0/0) 4(0/0/0) 5(0/1/0) ** BSET #,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) * BSET Dn,Mem 4(0/0/1) 4(0/0/1) 5(0/1/1) *Add Fetch Effective Address Time ** Add Fetch Immediate Address Time MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-35 Freescale Semiconductor, Inc. 8.2.14 Bit Field Manipulation Instructions The bit field manipulation instructions table indicates the number of clock periods needed for the processor to perform the specified bit field operation using the given addressing mode. Footnotes indicate when it is necessary to add another table entry to calculate the total effective execution time for the instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case 3(0/0/0) 6(0/0/0) 7(0/1/0) BFTST Dn BFTST Mem (< 5 Bytes) 11(1/0/0) 11(1/0/0) 12(1/1/0) BFTST Mem (5 Bytes) 15(2/0/0) 15(2/0/0) 16(2/1/0) BFCHG Dn 9(0/0/0) 12(0/0/0) 12(0/1/0) BFCHG Mem (< 5 Bytes) 16(1/0/1) 16(1/0/1) 16(1/1/1) BFCHG Mem (5 Bytes) 24(2/0/2) 24(2/0/2) 24(2/1/2) BFCLR Dn 9(0/0/0) 12(0/0/0) 12(0/1/0) BFCLR Mem (< 5 Bytes) 16(1/0/1) 16(1/0/1) 16(1/1/1) BFCLR Mem (5 Bytes) 24(2/0/2) 24(2/0/2) 24(2/1/2) BFSET Dn 9(0/0/0) 12(0/0/0) 12(0/1/0) BFSET Mem (< 5 Bytes) 16(1/0/1) 16(1/0/1) 16(1/1/1) BFSET Mem (5 Bytes) 24(2/0/2) 24(2/0/2) 24(2/1/2) BFEXTS Dn 5(0/0/0) 8(0/0/0) 8(0/1/0) BFEXTS Mem (< 5 Bytes) 13(1/0/0) 13(1/0/0) 13(1/1/0) BFEXTS Mem (5 Bytes) 18(2/0/0) 18(2/0/0) 18(2/1/0) BFEXTU Dn 5(0/0/0) 8(0/0/0) 8(0/1/0) BFEXTU Mem (< 5 Bytes) 13(1/0/0) 13(1/0/0) 13(1/1/0) BFEXTU Mem (5 Bytes) 18(2/0/0) 18(2/0/0) 18(2/1/0) BFINS Dn 7(0/0/0) 10(0/0/0) 10(0/1/0) BFINS Mem (< 5 Bytes) 14(1/0/1) 14(1/0/1) 15(1/1/1) BFINS Mem (5 Bytes) 20(2/0/2) 20(2/0/2) 21(2/1/2) BFFFO Dn 15(0/0/0) 18(0/0/0) 18(0/1/0) BFFFO Mem (< 5 Bytes) 24(1/0/0) 24(1/0/0) 24(1/1/0) BFFFO Mem (5 Bytes) 32(2/0/0) 32(2/0/0) 32(2/1/0) Add Calculate Immediate Address Time NOTE: A bit field of 32 bits may span five bytes that require two operand cycles to access or may span four bytes that require only one operand cycle to access. 8-36 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.15 Conditional Branch Instructions The conditional branch instructions table indicates the number of clock periods needed for the processor to perform the specified branch on the given branch size, with complete execution times given. No additional tables are needed to calculate total effective execution time for these instructions. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case Bcc (Taken) 3(0/0/0) 6(0/0/0) 9(0/2/0) Bcc.B (Not Taken) 1(0/0/0) 4(0/0/0) 5(0/1/0) Bcc.W (Not Taken) 3(0/0/0) 6(0/0/0) 7(0/1/0) Bcc.L (Not Taken) 3(0/0/0) 6(0/0/0) 9(0/2/0) DBcc (cc = False, Count Not Expired) 3(0/0/0) 6(0/0/0) 9(0/2/0) DBcc (cc = False, Count Expired) 7(0/0/0) 10(0/0/0) 10(0/3/0) DBcc (cc = True) 3(0/0/0) 6(0/0/0) 7(0/1/0) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-37 Freescale Semiconductor, Inc. 8.2.16 Control Instructions The control instructions table indicates the number of clock periods needed for the processor to perform the specified operation. Footnotes specify when it is necessary to add an entry from another table to calculate the total effective execution time for the given instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case ANDI to SR 9(0/0/0) 12(0/0/0) 15(0/2/0) EORI to SR 9(0/0/0) 12(0/0/0) 15(0/2/0) ORI to SR 9(0/0/0) 12(0/0/0) 15(0/2/0) ANDI to CCR 9(0/0/0) 12(0/0/0) 15(0/2/0) EORI to CCR 9(0/0/0) 12(0/0/0) 15(0/2/0) ORI to CCR 9(0/0/0) 12(0/0/0) 15(0/2/0) BSR 5(0/0/1) 7(0/0/1) 13(0/2/1) ** CALLM (Type 0) 28(2/0/6) 30(2/0/6) 36(2/2/6) ** CALLM (Type 1)--No Stack Copy 48(5/0/8) 50(5/0/8) 56(5/2/8) ** CALLM (Type 1)--No Stack Copy 55(6/0/8) 57(6/0/8) 64(6/2/8) ** CALLM (Type 1)--Stack Copy 63 + 6n (7 + n/0/8 + n) 65 + 6n (7 + n/0/8 + n) 71 + 6n (7 + n/2/8 + n) CAS (Successful Compare) 15(1/0/1) 15(1/0/1) 16(1/1/1) CAS (Unsuccessful Compare) 12(1/0/0) 12(1/0/0) 13(1/1/0) CAS2 (Successful Compare) 23(2/0/2) 25(2/0/2) 28(2/2/2) CAS2 (Unsuccessful Compare) 19(2/0/0) 22(2/0/0) 25(2/2/0) 8(0/0/0) 8(0/0/0) 8(0/1/0) 16(2/0/0) 18(2/0/0) 18(2/1/0) * CHK ** CHK2 EA,Rn % JMP 1(0/0/0) 4(0/0/0) 7(0/2/0) % JSR 3(0/0/1) 5(0/0/1) 11(0/2/1) LEA 2(0/0/0) 2(0/0/0) 3(0/1/0) LINK.W 3(0/0/1) 5(0/0/1) 7(0/1/1) LINK.L 4(0/0/1) 6(0/0/1) 10(0/2/1) NOP 2(0/0/0) 2(0/0/0) 3(0/1/0) PEA 3(0/0/1) 5(0/0/1) 6(0/1/1) RTD 9(1/0/0) 10(1/0/0) 12(1/2/0) RTM (Type 0) 18(4/0/0) 19(4/0/0) 22(4/2/0) RTM (Type 1) 31(6/0/1) 32(6/0/1) 35(6/2/1) RTR 13(2/0/0) 14(2/0/0) 15(2/2/0) RTS 9(1/0/0) 10(1/0/0) 12(1/2/0) UNLK 5(1/0/0) 6(1/0/0) 7(1/1/0) n--Number of Operand Transfers Required *Add Fetch Effective Address Time Add Calculate Effective Address Time 8-38 %--Add Jump Effective Address Time ** Add Fetch Immediate Address Time Add Calculate Immediate Address Time M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 8.2.17 Exception-Related Instructions The exception-related instructions table indicates the number of clock periods needed for the processor to perform the specified exception-related action. Footnotes specify when it is necessary to add the entry from another table to calculate the total effective execution time for the given instruction. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Instruction Best Case Cache Case Worst Case BKPT 9(1/0/0) 10(1/0/0) 10(1/0/0) Interrupt (I-Stack) 26(2/0/4) 26(2/0/4) 33(2/2/4) Interrupt (M-Stack) 41(2/0/8) 41(2/0/8) 48(2/2/8) RESET Instruction 518(0/0/0) 518(0/0/0) 519(0/1/0) STOP 8(0/0/0) 8(0/0/0) 8(0/0/0) Trace 25(1/0/5) 25(1/0/5) 32(1/2/5) TRAP #n 20(1/0/4) 20(1/0/4) 27(1/2/4) Illegal Instruction 20(1/0/4) 20(1/0/4) 27(1/2/4) A-Line Trap 20(1/0/4) 20(1/0/4) 27(1/2/4) F-Line Trap 20(1/0/4) 20(1/0/4) 27(1/2/4) Privilege Violation 20(1/0/4) 20(1/0/4) 27(1/2/4) TRAPcc (Trap) 23(1/0/5) 25(1/0/5) 32(1/2/5) TRAPcc (No Trap) 1(0/0/0) 4(0/0/0) 5(0/1/0) TRAPcc.W (Trap) 23(1/0/5) 25(1/0/5) 33(1/3/5) TRAPcc.W (No Trap) 3(0/0/0) 6(0/0/0) 7(0/1/0) TRAPcc.L (Trap) 23(1/0/5) 25(1/0/5) 33(1/3/5) TRAPcc.L (No Trap) 5(0/0/0) 8(0/0/0) 10(0/2/0) TRAPV (Trap) 23(1/0/5) 25(1/0/5) 32(1/2/5) TRAPV (No Trap) 1(0/0/0) 4(0/0/0) 5(0/1/0) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 8-39 Freescale Semiconductor, Inc. 8.2.18 Save and Restore Operations The save and restore operations table indicates the number of clock periods needed for the processor to perform the specified state save or return from exception, with complete execution times and stack length given. No additional tables are needed to calculate total effective execution time for these operations. The total number of clock cycles is outside the parentheses; the number of read, prefetch, and write cycles is given inside the parentheses as (r/p/w). These cycles are included in the total clock cycle number. Freescale Semiconductor, Inc... Operation Best Case Cache Case Worst Case Bus Cycle Fault (Short) 42(1/0/10) 43(1/0/10) 50(1/2/10) Bus Cycle Fault (Long) 79(1/0/24) 79(1/0/24) 86(1/2/24) RTE (Normal) 20(4/0/0) 21(4/0/0) 24(4/2/0) RTE (Six Word) 20(4/0/0) 21(4/0/0) 24(4/2/0) RTE (Throwaway)* 15(4/0/0) 16(4/0/0) 39(4/0/0) RTE (Coprocessor) 31(7/0/0) 32(7/0/0) 33(7/1/0) RTE (Short Fault) 42(10/0/0) 43(10/0/0) 45(10/2/0) RTE (Long Fault) 91(24/0/0) 92(24/0/0) 94(24/2/0) *Add the time for RTE on second stack frame. 8-40 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SECTION 9 APPLICATIONS INFORMATION Freescale Semiconductor, Inc... This section, which provides guidelines for using the MC68020/EC020, contains information on floating-point units, byte select logic, power and ground considerations, clock driver, memory interface, access time calculations, module support, and access levels. 9.1 FLOATING-POINT UNITS Floating-point support for the MC68020/EC020 is provided by the MC68881 floating-point coprocessor or the MC68882 enhanced floating-point coprocessor. Both devices offer a full implementation of the IEEE Standard for Binary Floating-Point Arithmetic (754). The MC68882 is a pin- and software-compatible upgrade of the MC68881, with an optimized MPU interface that provides over 1.5 times the performance of the MC68881 at the same clock frequency. Both coprocessors provide a logical extension to the integer data processing capabilities of the main processor. They contain a high-performance floating-point arithmetic unit and a set of floating-point data registers that are utilized in a manner that is analogous to the use of the integer data registers of the processor. The MC68881/MC68882 instruction set, a natural extension of all earlier members of the M68000 family, supports all addressing modes and data types of the host MC68020/EC020. The programmer perceives the MC68020/EC020 coprocessor execution model as if both devices are implemented on one chip. In addition to supporting the full IEEE standard, the MC68881 and MC68882 provide a full set of trigonometric and transcendental functions, on-chip constants, and a full 80-bit extended-precision real data format. The interface of the MC68020/EC020 to the MC68881 or MC68882 is easily tailored to system cost/performance needs. The MC68020/EC020 and the MC68881/MC68882 communicate via standard asynchronous M68000 bus cycles. All data transfers are performed by the main processor at the request of the MC68881/MC68882; thus, memory management, bus errors, address errors, and bus arbitration function as if the MC68881/MC68882 instructions are executed by the main processor. The floating-point unit and the processor can operate at different clock speeds, and up to seven floatingpoint coprocessors can simultaneously reside in an MC68020/EC020 system. Figure 9-1 illustrates the coprocessor interface connection of an MC68881/MC68882 to an MC68020/EC020 (uses entire 32-bit data bus). The MC68881/MC68882 is configured to operate with a 32-bit data bus when both its A0 and SIZE pins are connected to VCC. Refer to the MC68881UM/AD, MC68881/MC68882 Floating-Point Coprocessor User's Manual, for configuring the MC68881/MC68882 for smaller data bus widths. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-1 Freescale Semiconductor, Inc. MC68881/MC68882 MC68020/EC020 FC2-FC0 CHIP SELECT DECODE *A31-A20 A19-A16 A15-A13 A12-A5 A4-A1 A0 CS VCC VCC Freescale Semiconductor, Inc... AS DS R/W SIZE A4-A1 A0 AS DS R/W D31-D24 D23-D16 D15-D8 D7-D0 D31-D24 D23-D16 D15-D8 D7-D0 DSACK0 DSACK1 DSACK0 DSACK1 MAIN PROCESSOR CLOCK COPROCESSOR CLOCK * For the MC68EC020, A23-A0. Figure 9-1. 32-Bit Data Bus Coprocessor Connection The chip select (CS) decode circuitry is asynchronous logic that detects when a particular floating-point coprocessor is addressed. The MC68020/EC020 signals used by the logic include FC2-FC0 and A19-A13. Refer to Section 7 Coprocessor Interface Description for more information concerning the encoding of these signals. All or just a subset of these lines may be decoded, depending on the number of coprocessors in the system and the degree of redundant mapping allowed in the system. For example, if a system has only one coprocessor, the full decoding of the ten signals (FC2-FC0 and A19-A13), provided by the PAL equations in Figure 9-3, is not absolutely necessary. It may be sufficient to use only FC1-FC0 and A17-A16. FC1-FC0 indicate when a bus cycle is operating in either CPU space ($7) or user-defined space ($3), and A17-A16 encode the CPU space type as coprocessor space ($2). A15-A13 can be ignored in this case because they encode the coprocessor identification code (CpID) used to differentiate between multiple coprocessors in a system. Motorola assemblers always default to a CpID of $1 for floating-point instructions; this can be controlled with assembler directives if a different CpID is desired or if multiple coprocessors exist in the system. 9-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... The major concern of a system designer is to design a CS interface that meets the AC electrical specifications for both the MC68020/EC020 (MPU) and the MC68881/MC68882 (FPCP) without adding unnecessary wait states to FPCP accesses. The following maximum specifications (relative to CLK low) meet these objectives: tCLK low to AS low (MPU Spec 1 - MPU Spec 47A - FPCP Spec 19) (9-1) tCLK low to CS low (MPU Spec 1 - MPU Spec 47A - FPCP Spec 19) (9-2) Even though requirement (9-1) is not met under worst-case conditions, if the MPU AS is loaded within specifications and the AS input to the FPCP is unbuffered, the requirement is met under typical conditions. Designing the CS generation circuit to meet requirement (9-2) provides the highest probability that accesses to the FPCP occur without unnecessary wait states. A PAL 16L8 (see Figure 9-2) with a maximum propagation delay of 10 ns, programmed according to the equations in Figure 9-3, can be used to generate CS . For a 25-MHz system, tCLK low to CS low is less than or equal to 10 ns when this design is used. Should worst-case conditions cause t CLK low to AS low to exceed requirement (1), one wait state is inserted in the access to the FPCP; no other adverse effects occur. Figure 9-4 shows the bus cycle timing for this interface. Refer to MC68881UM/AD, MC68881/MC68882 Floating-Point Coprocessor User's Manual , for FPCP specifications. The circuit that generates CS must meet another requirement. When a nonfloating-point access immediately follows a floating-point access, CS (for the floating-point access) must be negated before AS and DS (for the subsequent access) are asserted. The PAL circuit previously described also meets this requirement. CLK AS FC2 FC1 FC0 A19 A18 A17 A16 GND PAL 16L8 10 ns VCC NC NC NC NC A13 A14 CLKD CS A15 Figure 9-2. Chip Select Generation PAL MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-3 Freescale Semiconductor, Inc. PAL16L8 FPCP CS GENERATION CIRCUITRY FOR 25 MHz OPERATION MOTOROLA INC., AUSTIN, TEXAS INPUTS: CLK ~AS OUTPUTS: ~CS CLKD FC2 FC1 FC0 A19 !~CS = FC2 *FC1 *FC0 *!A19 *!A18 *A17 *!A15 *!A14 *A13 A18 A17 A16 A14 A13 ;cpu space = $7 *!A16 ;coprocessor access = $2 ;coprocessor id = $1 *!CLK ;qualified by MPU clock low +FC2 *FC1 *FC0 *!A19 *!A18 *A17 *!A15 *!A14 *A13 +FC2 *FC1 *FC0 *!A19 *!A18 *A17 *!A15 *!A14 *A13 ;cpu space = $7 *!A16 ;coprocessor access = $2 ;coprocessor id = $1 *!~AS Freescale Semiconductor, Inc... A15 ;qualified by address strobe low ;cpu space = $7 *!A16 ;coprocessor access = $2 ;coprocessor id = $1 *CLKD ;qualified by CLKD (delayed CLK) CLKD = CLK Description: There are three terms to the CS generation. The first term denotes the earliest time CS can be asserted. The second term is used to assert CS until the end of the FPCP access. The third term is to ensure that no race condition occurs in case of a late AS. Figure 9-3. Chip Select PAL Equations CLK AS 9 CS 47A 8 DSACK1/DSACK0 19 START FPCP SPECIFICATION MPU SPECIFICATION Figure 9-4. Bus Cycle Timing Diagram 9-4 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 9.2 BYTE SELECT LOGIC FOR THE MC68020/EC020 The MC68020/EC020 architecture supports byte, word, and long-word operand transfers to any 8-, 16-, or 32-bit data port, regardless of alignment. This feature allows the programmer to write code that is not bus-width specific. When accessed, the peripheral or memory subsystem reports its actual port size to the controller, and the MC68020/EC020 then dynamically sizes the data transfer accordingly, using multiple bus cycles when necessary. The following paragraphs describe the generation of byte select control signals that enable the dynamic bus sizing mechanism, the transfer of differently sized operands, and the transfer of misaligned operands to operate correctly. The following signals control the MC68020/EC020 operand transfer mechanism: Freescale Semiconductor, Inc... A1, A0 SIZ1, SIZ0 R/ W -- Address signals. The most significant byte of the operand to be transferred is addressed directly. -- Transfer size signals. Output of the MC68020/EC020. These indicate the number of bytes of an operand remaining to be transferred during a given bus cycle. -- Read/Write signal. Output of the MC68020/EC020. For byte select generation in MC68020/EC020 systems. DSACK1, DSACK0 -- Data transfer and size acknowledge signals. Driven by an asynchronous port to indicate the actual bus width of the port. The MC68020/EC020 assumes that 16-bit ports are situated on data lines D31-D16, and that 8-bit ports are situated on data lines D31-D24. This ensures that the following logic works correctly with the MC68020/EC020's on-chip internal-to-external data bus multiplexer. Refer to Section 5 Bus Operation for more details on the dynamic bus sizing mechanism. The need for byte select signals is best illustrated by an example. Consider a long-word write cycle to an odd address in word-organized memory. The transfer requires three bus cycles to complete. The first bus cycle transfers the most significant byte of the long word on D23-D16. The second bus cycle transfers a word on D31-D16, and the last bus cycle transfers the least significant byte of the original long word on D31-D24. To prevent overwriting those bytes that are not used in these transfers, a unique byte data strobe must be generated for each byte when using devices with 16- and 32-bit port widths. For noncachable read cycles and all write cycles, the required active bytes of the data bus for any given bus transfer are a function of the SIZ1, SIZ0 and A1, A0 outputs (see Table 9-1). Individual strobes or select signals can be generated by decoding these four signals for every bus cycle. Devices residing on 8-bit ports can utilize DS or AS since there is only one valid byte for any transfer. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-5 Freescale Semiconductor, Inc. Table 9-1. Data Bus Activity for Byte, Word, and Long-Word Ports Data Bus Active Sections Byte (B), Word (W), Long-Word (L) Ports Freescale Semiconductor, Inc... Transfer Size SIZ1 SIZ0 A1 A0 D31-D24 D23-D16 D15-D8 D7-D0 Byte 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 BWL B BW B -- WL -- W -- -- L -- -- -- -- L Word 1 1 1 1 0 0 0 0 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W -- L L -- -- -- L L 3 Bytes 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W L L L -- -- L L L Long Word 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 BWL B BW B WL WL W W L L L -- L L L L During cachable read cycles, the addressed device must provide valid data over its full bus width as indicated by DSACK1/ DSACK0. While instructions are always prefetched as long-word-aligned accesses, data fetches can occur with any alignment and size. Because the MC68020/EC020 assumes that the entire data bus port size contains valid data, cachable data read bus cycles must provide as much data as signaled by the port size during a bus cycle. To satisfy this requirement, the R/ W signal must be included in the byte select logic for the MC68020/EC020. Figure 9-5 shows a block diagram of an MC68020/EC020 system with a single memory bank. The PAL provides memory-mapped byte select signals for an asynchronous 32-bit port and unmapped byte select signals for other memory banks or ports. Figure 9-6 provides sample equations for the PAL. The PAL equations and circuits presented here cannot be the optimal implementation for every system. Depending on the CPU clock frequency, memory access times, and system architecture, different circuits may be required. 9-6 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. MC68020/EC020 PAL16L8 SIZ0 SIZ1 A0 A1 FC0 FC1 UUDA UMDA LMDA LLDA UUDA UMDA LMDA LLDA UNMAPPED BYTE SELECTS FOR OTHER 32-BIT PORTS CPU LLDB LMDB UMDB UUDB MC74F00 A21-A18 MC74F32 MC74F32 MC74F32 MC74F32 *A31-A2 AS R/W Freescale Semiconductor, Inc... D31-D0 32-BIT PORT *A31-A2 W E W E W E W E MCM60256A MCM60256A MCM60256A MCM60256A D7-D0 D15-D8 D23-D16 D31-D24 * For the MC68EC020, A23-A2. Figure 9-5. Example MC68020/EC020 Byte Select PAL System Configuration MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-7 Freescale Semiconductor, Inc. PAL16L8 BYTE_SELECT MC68020/EC020 BYTE DATA SELECT GENERATION FOR 32-BIT PORTS, MAPPED AND UNMAPPED. MOTOROLA INC., AUSTIN, TEXAS INPUTS: A0 OUTPUTS: ~UUDA !~UUDA = RW +!A0 *!A1 = RW +A0 *!A1 +!A1 *!SIZ0 +!A1 *SIZ1 = RW ;directly addressed, any size +!A1 *!SIZ0 *!SIZ1 +!A1 *SIZ0 *SIZ1 +!A1 *A0 *!SIZ0 = RW +A0 *A1 +A0 *SIZ0 *SIZ1 +!SIZ0 *!SIZ1 +A1 *SIZ1 ;enable upper byte on read of 32-bit port ;directly addressed, any size ;enable upper middle byte on read of 32-bit port ;directly addressed, any size ;even word aligned, size word or long word ;even word aligned, size is word or three byte ;enable lower middle byte on read of 32-bit port = RW *!~CPU * (addressb) +!A0 *!A1 *!~CPU * (addressb) = RW *!~CPU * (addressb) + A0 *!A1 *!~CPU * (addressb) +!A1 *!SIZ0 *!~CPU * (addressb) +!A1 *SIZ1 *!~CPU * (addressb) =RW *!~CPU * (addressb) +!A0 * A1 *!~CPU * (addressb) +!A1 *!SIZ0 *!SIZ1 *!~CPU * (addressb) +!A1 * SIZ0 * SIZ1 *!~CPU * (addressb) +!A1 * A0 *!SIZ0 *!~CPU * (addressb) =RW *!~CPU * (addressb) +A0 * A1 *!~CPU * (addressb) + A0 * SIZ0 * SIZ1 *!~CPU * (addressb) +!SIZ0 *!SIZ1 *!~CPU * (addressb) +A1 * SIZ1 *!~CPU * (addressb) ;enable upper byte on read of 32-bit port ;directly addressed, any size ;enable upper middle byte on read of 32-bit port ;directly addressed, any size ;even word aligned, size word or long word ;even word aligned, size is word or three byte ;enable lower middle byte on read of 32-bit port ;directly addressed, any size ;even word aligned, size is long word ;even word aligned, size is three byte ;even word aligned, size is word or long word ;enable lower byte on read of 32-bit port ;directly addressed, any size ;odd byte alignment, three byte size ;size is long word, any address ;odd word aligned, word or three byte size !~UMDA Freescale Semiconductor, Inc... !~LMDA !~LLDA !~UUDB !~UMDB !~LMDB !~LLDB A1 SIZ0 SIZ1 ~UMDA RW ~LMDA A18 ~LLDA A19 ~UUDA A20 A21 ~UMDB ~CPU ~LMDB ~LLDB +!A0 *A1 ;even word aligned, size is long word ;even word aligned, size is three byte ;even word aligned, size is word or long word ;enable lower byte on read of 32-bit port ;directly addressed, any size ;odd byte alignment, three byte size ;size is long word, any address ;odd word aligned, word or three byte size DESCRIPTION : Byte select signals for writing. On reads, all byte selects are asserted if the respective memory block is addressed. The input signal CPU prevents byte select assertion during CPU space cycles and is derived from NANDing FC1-FC0 or FC2-FC0. The label (addressb) is a designer-selectable combination of address lines used to generate the proper address decode for the system's memory bank. With the address lines given here, the decode block size is 256 Kbytes to 2 Mbytes. A similar address might be included in the equations for UUDA , UMDA, etc. if the designer wishes them to be memory mapped also. Figure 9-6. MC68020/EC020 Byte Select PAL Equations 9-8 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 9.3 POWER AND GROUND CONSIDERATIONS Freescale Semiconductor, Inc... The MC68020/EC020 is fabricated in Motorola's advanced HCMOS process and is capable of operating at clock frequencies of up to 25 MHz. While the use of CMOS for a device containing such a large number of transistors allows significantly reduced power consumption compared to an equivalent NMOS circuit, the high clock speed makes the characteristics of power supplied to the device very important. The power supply must be able to furnish large amounts of instantaneous current when the MC68020/EC020 performs certain operations, and it must remain within the rated specification at all times. To meet these requirements, more detailed attention must be given to the power supply connection to the MC68020/EC020 than is required for NMOS devices operating at slower clock rates. To reduce the amount of noise in the power supply connected to the MC68020/EC020 and to provide for the instantaneous current requirements, common capacitive decoupling techniques should be observed. While there is no recommended layout for this capacitive decoupling, it is essential that the inductance and distance between these devices and the MC68020/EC020 be minimized to provide sufficiently fast response time to satisfy momentary current demands and to maintain a constant supply voltage. It is suggested that high-frequency, high-quality capacitors be placed as close to the MC68020/EC020 as possible. Table 9-2 lists the VCC and GND pin assignments for the MC68EC020 PPGA (RP suffix) package. Table 9-3 lists the V C C and GND pin assignments for the MC68EC020 PQFP (FG suffix) package. Refer to Section 11 Ordering Information and Mechanical Data for the V CC and GND pin assignments for the MC68020 packages. When assigning capacitors to the V CC and GND pins, the noisier pins (address and data buses) should be heavily decoupled from the internal logic pins. Typical decoupling practices include a high-frequency, high-quality capacitor to decouple every device on the printed circuit board; however, due to the power requirements and drive capability of the MC68020/EC020, each V CC pin should be decoupled with an individual capacitor. Motorola recommends using a capacitor in the range of 0.01 F to 0.1 F on each VCC pin on each device to provide filtering for most frequencies prevalent in a digital system. In addition to the individual decoupling, several bulk decoupling capacitors should be placed onto the printed circuit board with typical values in the range of 33 F to 330 F. When power and ground planes are used with an adequate number of high-frequency, highquality capacitors, the system noise will be reduced to the required levels, and the MC68020/EC020 will function properly. Similar decoupling techniques should also be observed for other VLSI devices in the system. In addition to the capacitive decoupling of the power supply, care must be taken to ensure a low-impedance connection between all MC68020/EC020 VCC and GND pins and the system power supply. A solid power supply connection from the power and ground planes to the MC68020/EC020 V CC and GND pins, respectively, will meet this requirement. Failure to provide connections of sufficient quality between the MC68020/EC020 power pins and the system power supplies will result in increased assertion delays for external signals, decreased voltage noise margins, increased system noise, and possible errors in MC68020/EC020 internal logic. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-9 Freescale Semiconductor, Inc. Table 9-2. VCC and GND Pin Assignments-- MC68EC020 PPGA (RP Suffix) Pin Group Address Bus Data Bus Internal Logic Clock VCC GND B7, C7 A1, A7, C8, D13 K12, M9, N9 J13, L8, M1, M8 D1, D2, E12, E13 F11, F12, J1, J2 -- B1 Table 9-3. VCC and GND Pin Assignments-- MC68EC020 PQFP (FG Suffix) Freescale Semiconductor, Inc... Pin Group Address Bus Data Bus Internal Logic Clock VCC GND 90 72, 89, 100 44, 57 26, 43, 58, 59 7, 8, 70, 71 3, 20, 21, 68, 69 -- 4 9.4 CLOCK DRIVER The MC68020/EC020 is designed to sustain high performance while using low-cost memory subsystems. The MC68020/EC020 requires a stable clock source that is free of ringing and ground bounce, has sufficient rise and fall times, and meets the minimum and maximum high and low cycle times. The individual system may require additional clocks for peripherals with a minimum amount of clock skew. Two possible clock solutions are provided with the MC88916 and MC74F803. Many other clock solutions can be used. Some crystal clock drivers are capable of driving the MC68020/EC020 directly. For slower speed designs, a simple 74F74 flip-flop meets the clocking needs of the MC68020/EC020. Coupled with the MC88916 or MC74F803 clock generation and distribution circuit, the MC68020/EC020 provides simple interface to lower speed memory subsystems. The MC88916 (see Figure 9-7) and MC74F803 (see Figure 9-8) generate the clock signals required to minimize the skew between different clocks to multiple devices such as coprocessors, synchronous state machines, DRAM controllers, and memory subsystems. The MC88916 clock driver can be used in doubling and synchronizing a low-frequency clock source. The MC74F803 will provide a controlled skew output for clocking other peripherals. 9-10 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. CONTROLLER CLOCK (25 MHz) 12.5-MHz OSCILLATOR 12.5 MHz MC88916 2 CLOCK (50 MHz) MC68020/EC020 25 MHz BUS CLOCKS (25 MHz) CLOCK (25 MHz) Freescale Semiconductor, Inc... Figure 9-7. High-Resolution Clock Controller CONTROLLER CLOCK (25 MHz) 50-MHz OSCILLATOR MC74F803 MC68020/EC020 25 MHz 2 CLOCK (25 MHz) BUS CLOCKS (25 MHz) Figure 9-8. Alternate Clock Solution 9.5 MEMORY INTERFACE The MC68020/EC020 is capable of running an external bus cycle in a minimum of three clocks (refer to Section 5 Bus Operation). The MC68020/EC020 runs an asynchronous bus cycle, terminated by the DSACK1/DSACK0 signals, and has a minimum duration of three controller clock periods in which up to four bytes (32 bits) are transferred. During read operations, the MC68020/EC020 latches data on the last falling clock edge of the bus cycle, one-half clock before the bus cycle ends. Latching data here, instead of the next rising clock edge, helps to avoid data bus contention with the next bus cycle and allows the MC68020/EC020 to receive the data into its execution unit sooner for a net performance increase. Write operations also use this data bus timing to allow data hold times from the negating strobes and to avoid any bus contention with the following bus cycle. This MC68020/EC020 characteristic allows the system to be designed with a minimum of bus buffers and latches. One benefit of the MC68020/EC020 on-chip instruction cache is that the effect of external wait states on performance is lessened because the caches are always accessed in fewer than "no wait states," regardless of the external memory configuration. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-11 Freescale Semiconductor, Inc. 9.6 ACCESS TIME CALCULATIONS Freescale Semiconductor, Inc... The timing paths that are critical in any memory interface are illustrated and defined in Figure 9-9. The type of device that is interfaced to the MC68020/EC020 determines exactly which of the paths is most critical. The address-to-data paths are typically the critical paths for static devices since there is no penalty for initiating a cycle to these devices and later validating that access with the appropriate bus control signal. Conversely, the addressstrobe-to-data-valid path is often most critical for dynamic devices since the cycle must be validated before an access can be initiated. For devices that signal termination of a bus cycle before data is validated (e.g., error detection and correction hardware and some external caches), to improve performance, the critical path may be from the address or strobes to the assertion of BERR (or BERR and HALT). Finally, the address-valid-toDSACK1/DSACK0- asserted path is most critical for very fast devices and external caches, since the time available between the address becoming valid and the DSACK1/DSACK0 assertion to terminate the bus cycle is minimal. Table 9-4 provides the equations required to calculate the various memory access times assuming a 50percent duty cycle clock. S0 S1 S2 S0 CLK *A31-A0 a c e d f AS b DSACK1/DSACK0 BERR, HALT D31-D0 * For the MC68EC020, A23-A0. NOTE: This diagram illustrates access time calculations only Parameter Description a Address Valid to DSACK1/DSACK0 Asserted b AS Asserted to DSACK1/DSACK0 Asserted c Address Valid to BERR/HALT Asserted d AS Asserted to BERR/HALT Asserted e Address Valid to Data Valid f AS Asserted to Data Valid 9-12 System tAVDL tSADL tAVBHL tSABHL tAVDV tSADV M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com Equation 9-3 9-4 9-5 9-6 9-7 9-8 MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Figure 9-9. Access Time Computation Diagram MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-13 Freescale Semiconductor, Inc. Table 9-4. Memory Access Time Equations at 16.67 and 25 MHz Equation N=3 N=4 N=5 N=6 N=7 Unit 9-3 t AVDL = (N - 1) * t1 - t2 - t6 - t47A 61 121 181 241 301 ns 9-4 t SADL = (N - 1) * t1 - t9 - t60 25 85 145 205 265 ns 9-5 t AVBHL = N * t1 - t2 - t6 - t27A 22 46 70 94 118 ns 9-6 t SABHL = (N - 1) * t1 - t9 - t27A 40 70 100 130 160 ns 9-7 t AVDV = N * t1 - t2 - t6 - t27 121 181 241 301 361 ns 9-8 t SADV = (N - 1) * t1 - t9 - t27 85 145 205 265 325 ns N=3 N=4 N=5 N=6 N=7 Unit Equation Freescale Semiconductor, Inc... 16.667 MHz 25 MHz 9-3 t AVDL = (N - 1) * t1 - t2 - t6 - t47A 31 71 111 151 191 ns 9-4 t SADL = (N - 1) * t1 - t9 - t60 17 57 97 137 177 ns 9-5 t AVBHL = N * t1 - t2 - t6 - t27A 22 41 60 79 98 ns 9-6 t SABHL = (N - 1) * t1 - t9 - t27A 26 44 62 80 98 ns 9-7 t AVDV = N * t1 - t2 - t6 - t27 71 111 151 191 231 ns 9-8 t SADV = (N - 1) * t1 - t9 - t27 57 97 137 177 217 ns Where: tX t1 t2 t3 t6 t9 t27 t27A t47A N = = = = = = = = = = Refers to AC Electrical Specification X The Clock Period The Clock Low Time The Clock High Time The Clock High to Address Valid Time The Clock Low to AS Low Delay The Data-In to Clock Low Setup Time The BERR/ HALT to Clock Low Setup Time The Asynchronous Input Setup Time The Total Number of Clock Periods in the Bus Cycle (N 3 Cycles) During asynchronous bus cycles, DSACK1/DSACK0 are used to terminate the current bus cycle. In true asynchronous operations, such as accesses to peripherals operating at a different clock frequency, either or both signals may be asserted without regard to the clock, and then data must be valid a certain amount of time later as defined by specification 31. With a 25-MHz controller, this time is 32 ns after DSACK1 /DSACK0 asserts; with a 16.67-MHz controller, this time is 50 ns after DSACK1/DSACK0 asserts (both numbers vary with the actual clock frequency). However, many local memory systems do not operate in a truly asynchronous manner because either the memory control logic can be related to the MC68020/EC020 clock or worst-case propagation delays are known; thus, asynchronous setup times for the DSACK1/DSACK0 signals can be guaranteed. The timing requirements for this pseudosynchronous DSACK1/ DSACK0 generation is governed by the equation for tAVDL. 9-14 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Another way to optimize the CPU-to-memory access times in a system is to use a clock frequency less than the rated maximum of the specific MC68020/EC020 device. Table 9-5 provides calculated t A V D V (see Equation 9-7 of Table 9-4) results for a 16 MHz MC68020/EC020 and a 25 MHz MC68020/EC020 operating at various clock frequencies. If the system uses other clock frequencies, the above equations can be used to calculate the exact access times. Table 9-5. Calculated t AVDV Values for Operation at Frequencies Less Than or Equal to the CPU Maximum Frequency Rating Equation 9-7 tAVDV Freescale Semiconductor, Inc... Clocks Per (N) and Type Bus Cycle 16-MHz MC68020/EC020 25-MHz MC68020/EC020 Wait States Clock at 12.5 MHz Clock at 16.67 MHz Clock at 16.67 MHz Clock at 20 MHz Clock at 25 MHz 3 Clock Asynchronous 0 181 121 131 101 71 4 Clock Asynchronous 1 261 181 191 151 111 5 Clock Asynchronous 2 341 241 251 201 151 6 Clock Asynchronous 3 421 301 311 251 191 9.7 MODULE SUPPORT The MC68020/EC020 includes support for modules with the CALLM and RTM instructions. The CALLM instruction references a module descriptor. This descriptor contains control information for entry into the called module. The CALLM instruction creates a module stack frame and stores the current module state in that frame and loads a new module state from the referenced descriptor. The RTM instruction recovers the previous module state from the stack frame and returns to the calling module. The module interface facilitates finer resolution of access control by external hardware. Although the MC68020/EC020 does not interpret the access control information, it communicates with external hardware when the access control is to be changed and relies on the external hardware to verify that the changes are legal. 9.7.1 Module Descriptor Figure 9-10 illustrates the format of the module descriptor. The first long word contains control information used during execution of the CALLM instruction. The remaining locations contain data that can be loaded into processor registers by the CALLM instruction. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-15 Freescale Semiconductor, Inc. 31 BASE +$04 29 28 OPT 24 23 TYPE 16 15 0 (RESERVED, MUST BE ZERO) ACCESS LEVEL MODULE ENTRY WORD POINTER +$08 MODULE DATA AREA POINTER +$0C +$10 ADDITIONAL USER-DEFINED INFORMATION Freescale Semiconductor, Inc... Figure 9-10. Module Descriptor Format The opt field specifies how arguments are to be passed to the called module; the MC68020/EC020 recognizes only the options of 000 and 100; all others cause a format exception. The 000 option indicates that the called module expects to find arguments from the calling module on the stack just below the module stack frame. In cases where there is a change of stack pointer during the call, the MC68020/EC020 will copy the arguments from the old stack to the new stack. The 100 option indicates that the called module will access the arguments from the calling module through an indirect pointer in the stack of the calling module. Hence, the arguments are not copied, but the MC68020/EC020 puts the value of the stack pointer from the calling module in the module stack frame. The type field specifies the type of the descriptor; the MC68020/EC020 only recognizes descriptors of type $00 and $01; all others cause a format exception. The $00 type descriptor defines a module for which there is no change in access rights, and the called module builds its stack frame on top of the stack used by the calling module. The $01 type descriptor defines a module for which there may be a change in access rights; such a called module may have a separate stack area from that of the calling module. The access level field is used only with the type $01 descriptor and is passed to external hardware to change the access control. The module entry word pointer specifies the entry address of the called module. The first word at the entry address (see Figure 9-11) specifies the register to be saved in the module stack frame and then loaded with the module descriptor data area pointer; the first instruction of the module starts with the next word. The module descriptor data area pointer field contains the address of the called module data area. If the access change requires a change of stack pointer, the old value is saved in the module stack frame, and the new value is taken from the module descriptor stack pointer field. Any further information in the module descriptor is user defined. 15 D/A 14 12 REGISTER 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 OPERATION WORD OF FIRST INSTRUCTION Figure 9-11. Module Entry Word 9-16 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. All module descriptor types $10-$1F are reserved for user definition and cause a format error exception. This provides the user with a means of disabling any module by setting a single bit in its descriptor without loss of any descriptor information. If the called module does not wish the module data area pointer to be loaded into a register, the module entry word can select register A7, and the loaded value will be overwritten with the correction stack pointer value after the module stack frame is created and filled. Freescale Semiconductor, Inc... 9.7.2 Module Stack Frame Figure 9-12 illustrates the format of the module stack frame. This frame is constructed by the CALLM instruction and is removed by the RTM instruction. The first and second long words contain control information passed by the CALLM instruction to the RTM instruction. The module descriptor pointer contains the address of the descriptor used during the module call. All other locations contain information to be restored on return to the calling module. The PC is the saved address of the instruction following the CALLM instruction. The opt and type fields, which specify the argument options and type of module stack frame, are copied to the frame from the module descriptor by the CALLM instruction; the RTM instruction will cause a format error if the opt and type fields do not have recognizable values. The access level is the saved access control information, which is saved from external hardware by the CALLM instruction and restored by the RTM instruction. The argument count field is set by the CALLM instruction and is used by the RTM instruction to remove arguments from the stack of the calling module. The contents of the CCR are saved by the CALLM instruction and restored by the RTM instruction. The saved stack pointer field contains the value of the stack pointer when the CALLM instruction started execution, and that value is restored by RTM. The saved module data area pointer field contains the saved value of the module data area pointer register from the calling module. 15 SP 13 12 8 7 OPT TYPE 0 SAVED ACCESS LEVEL 0 0 0 0 0 0 0 0 CONDITION CODES 0 0 0 0 0 0 0 0 ARGUMENT COUNT (RESERVED) +$08 +$0C +$10 MODULE DESCRIPTION POINTER SAVED PROGRAM COUNTER SAVED MODULE DATA AREA POINTER +$18 ARGUMENTS (OPTIONAL) Figure 9-12. Module Call Stack Frame MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-17 Freescale Semiconductor, Inc. 9.8 ACCESS LEVELS Freescale Semiconductor, Inc... The MC68020/EC020 module mechanism supports a finer level of access control beyond the distinction between user and supervisor privilege levels. The module mechanism allows a module with limited access rights to call a module with greater access rights. With the help of external hardware, the processor can verify that an increase in access rights is allowable or can detect attempts by a module to gain access rights to which it is not entitled. Type $01 module descriptors and module stack frames indicate a request to change access levels. While processing a type $01 descriptor or frame, the CALLM and RTM instructions communicate with external access control hardware via accesses in the CPU space. For these accesses, A19-A16 equal 0001. Figure 9-13 shows the address map for these CPU space accesses. If the processor receives a bus error on any of these CPU space accesses during the execution of a CALLM or RTM instruction, the processor will take a format error exception. 31 24 23 0 $00 CAL (UNUSED, RESERVED) $04 ACCESS STATUS REGISTER (UNUSED, RESERVED) $08 IAL (UNUSED, RESERVED) $0C DAL (UNUSED, RESERVED) $40 FUNCTION CODE 0 DESCRIPTOR ADDRESS $44 FUNCTION CODE 1 DESCRIPTOR ADDRESS (USER DATA) $48 FUNCTION CODE 2 DESCRIPTOR ADDRESS (USER PROGRAM) $4C FUNCTION CODE 3 DESCRIPTOR ADDRESS $50 FUNCTION CODE 4 DESCRIPTOR ADDRESS (SUPERVISOR DATA) $54 FUNCTION CODE 5 DESCRIPTOR ADDRESS (SUPERVISOR PROGRAM) $58 FUNCTION CODE 6 DESCRIPTOR ADDRESS $5C FUNCTION CODE 7 DESCRIPTOR ADDRESS (CPU SPACE) Figure 9-13. Access Level Control Bus Registers The current access level register (CAL) contains the access level rights of the currently executing module. The increase access level register (IAL) is the register through which the processor requests increased access rights. The decrease access level register (DAL) is the register through which the processor requests decreased access rights. The formats of these three registers are undefined to the main processor, but the main processor assumes that information read from the module descriptor stack frame or the CAL can be meaningfully written to the IAL or the DAL. The access status register allows the processor to query the external hardware as to the legality of intended access level transitions. Table 9-6 lists the valid values of the access status register. 9-18 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 9-6. Access Status Register Codes Value Validity Processor Action $00 Invalid $01 Valid No Change in Access Rights $02-$03 Valid Change Access Rights with No Change of Stack Pointer $04-$07 Valid Change Access Rights and Change Stack Pointer Other Undefined Format Error Undefined (Take Format Error Exception) Freescale Semiconductor, Inc... The processor uses the descriptor address registers during the CALLM instruction to communicate the address of the type $01 descriptor, allowing external hardware to verify that the address is a valid address for a type $01 descriptor. This validation prevents a module from creating a type $01 descriptor to increase its access rights. 9.8.1 Module Call The CALLM instruction is used to make the module call. For the type $00 module descriptor, the processor creates and fills the module stack frame at the top of the active system stack. The condition codes of the calling module are saved in the CCR field of the frame. If opt is equal to 000 (arguments passed on the stack) in the module descriptor, the MC68020/EC020 does not save the stack pointer or load a new stack pointer value. The processor uses the module entry word to save and load the module data area pointer register and then begins execution of the called module. For the type $01 module descriptor, the processor must first obtain the current access level from external hardware. It also verifies that the calling module has the right to read from the area pointed to by the current value of the stack pointer by reading from that address. It passes the descriptor address and increase access level to external hardware for validation and then reads the access status. If external hardware determines that the change in access rights should not be granted, the access status is zero, and the processor takes a format error exception. No visible processor registers are changed, nor should the current access level enforced by external hardware be changed. If external hardware determines that a change should be granted, the external hardware changes its access level, and the processor proceeds. If the access status register indicates that a change in the stack pointer is required, the stack pointer is saved internally, a new value is loaded from the module descriptor, and arguments are copied from the calling stack to the new stack. Finally, the module stack frame is created and filled on the top of the current stack. The condition codes of the calling module are saved in the CCR field of the frame. Execution of the called module then begins as with a type $00 descriptor. MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 9-19 Freescale Semiconductor, Inc. 9.8.2 Module Return Freescale Semiconductor, Inc... The RTM instruction is used to return from a module. For the type $00 module stack frame, the processor reloads the condition codes, the PC, and the module data area pointer register from the frame. The frame is removed from the top of the stack, the argument count is added to the stack pointer, and execution returns to the calling module. For the type $01 module stack frame, the processor reads the access level, condition codes, PC, saved module data area pointer, and saved stack pointer from the module stack frame. The access level is written to the DAL for validation by external hardware; the processor then reads the access status to check the validation. If the external hardware determines that the change in access right should not be granted, the access status is zero, and the processor takes a format error exception. No visible processor registers are changed, nor should the current access level enforced by external hardware be changed. If the external hardware determines that the change in access rights should be granted, the external hardware changes its access level, the values read from the module stack frame are loaded into the corresponding processor registers, the argument count is added to the new stack pointer value, and execution returns to the calling module. If the called module does not wish the saved module data pointer to be loaded into a register, the RTM instruction word can select register A7, and the loaded value will be overwritten with the correct stack pointer value after the module stack frame is deallocated. 9-20 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SECTION 10 ELECTRICAL CHARACTERISTICS Freescale Semiconductor, Inc... This section provides the thermal characteristics and electrical specifications for the MC68020/EC020. Note that the thermal and DC electrical characteristics are listed separately for the MC68020 and the MC68EC020. All other data applies to both the MC68020 and the MC68EC020 unless otherwise noted. 10.1 MAXIMUM RATINGS Rating Supply Voltage Input Voltage Operating Temperature Range Minimum Ambient Temperature Maximum Ambient Temperature PGA, PPGA, PQFP Maximum Junction Temperature CQFP Storage Temperature Range Symbol Value Unit VCC 0.3 to +7.0 V Vin 0.5 to +7.0 V TA 0 C TA 70 C TJ 110 C Tstg 55 to 150 C The device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, normal precautions should be taken to avoid application of voltages higher than maximumrated voltages to these highimpedance circuits. Tying unused inputs to the appropriate logic voltage level (e.g., either GND or VC C ) enhances reliability of operation. 10.2 THERMAL CONSIDERATIONS The average chip-junction temperature, TJ, in C can be obtained from: TJ = TA + (PD qJA) (10-1) where: TA qJA PD PINT PI/O = = = = = Ambient Temperature, C Package Thermal Resistance, Junction-to-Ambient, C/W PINT + PI/O ICC X VCC, WattsNChip Internal Power Power Dissipation on Input and Output PinsNUser Determined For most applications, PI/O < PINT and can be neglected. An approximate relationship between PD and TJ (if PI/O is neglected) is: PD = K (TJ + 273C) MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com (10-2) 10-1 Freescale Semiconductor, Inc. Solving Equations (10-1) and (10-2) for K gives: K = PD (TA + 273C) + qJAPD2 (10-3) where K is a constant pertaining to the particular part. K can be determined from equation (10-3) by measuring PD (at thermal equilibrium) for a known TA. Using this value of K, the values of PD and TJ can be obtained by solving equations (10-1) and (10-2) iteratively for any value of TA. Freescale Semiconductor, Inc... The total thermal resistance of a package (qJA) can be separated into two components, qJC and qCA. qJC represents the barrier to heat flow from the semiconductor junction to the package (case) surface, and qCA represents the barrier to heat flow from the case to the ambient air. These terms are related by the equation: qJA=qJC + qCA (10-4) q JC is device related and cannot be influenced by the user. However, qCA is user dependent and can be minimized by such thermal management techniques as heat sinks, forced air cooling, and use of thermal convection to increase air flow over the device. Thus, good thermal design on the part of the user can significantly reduce qCA so that qJA approximately equals qJC. Substitution of qJC for qJA in equation (10-1) results in a lower semiconductor junction temperature. 10.2.1 MC68020 Thermal Characteristics and DC Electrical Characteristics MC68020 Thermal Resistance (C/W) The following table provides thermal resistance characteristics for junction to ambient and junction to case for the MC68020 packages with natural convection and no heatsink. CharacteristicNNatural Convection and No Heatsink Thermal Resistance PGA Package (RC Suffix) PPGA Package (RP Suffix) CQFP Package (FE Suffix) PQFP Package (FC Suffix) q JA q JC 26 32 46 42 3 10 15 20 Resistance is to bottom center (pin side) of case for PGA and PPGA packages, top center of case for CQFP and PQFP packages. MC68020 CQFP Package Table 10-1 provides typical and worst case thermal characteristics for the MC68020 CQFP package both with and without a heatsink. The heatsink used is black anodized aluminum alloy, 0.72"x0.75"x0.6" high with an omnidirectional 5x6 array of fins. Attachment was made using Epolite 6400 one part epoxy. 10-2 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Table 10-1. qJA vs. AirflowNMC68020 CQFP Package Airflow in Linear Feet/Minute q JA 0* 200 500 Maximum No Heatsink With Heatsink 46 35 28 20 24 18 Typical No Heatsink With Heatsink 43 32 25 17 21 15 Freescale Semiconductor, Inc... *Natural convection Table 10-2 shows the relationship between clock speed and power dissipation for any package type. The worst case operating conditions are used for thermal management design, while typical values are used for reliability analysis. Table 10-2. Power vs. Rated Frequency (at TJ Maximum = 110C) Rated Frequency (MHz) PD Maximum (Watts) PD Typical (Watts) 33 25 20 16 1.4 1.2 1.0 0.9 0.84 0.72 0.60 0.54 Table 10-3 shows the relationship between board temperature rise and power dissipation in the test environment for the CQFP package. Derate qJA based on measurements made in the application by adding (0.8/PD) * [Tba(application) Tba(table)] to the qJA values in the table. Board temperature was measured on the top surface of the board directly under the device. Table 10-3. Temperature Rise of Board vs. PD NMC68020 CQFP Package PD Natural Convection Tba (C)NNo Heatsink 0.6W 1.0W 1.75W 18 27 53 Values for thermal resistance presented in this document were derived using the procedure described in Motorola Reliability Report 7843, OThermal Resistance Measurement Method for MC68XX Microcomponent Devices,O and are provided for design purposes only. Thermal measurements are complex and dependent on procedure and setup. User-derived values for thermal resistance may differ. MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-3 Freescale Semiconductor, Inc. MC68020 DC Electrical Characteristics (VCC = 5.0 Vdc 5%; GND = 0 Vdc; Temperature within defined ranges) Characteristics Symbol Min Max Unit Input High Voltage VIH 2.0 VCC V Input Low Voltage VIL GND 0.5 0.8 V 1.0 20 1.0 20 20 20 2.4 N N N N N 0.5 0.5 0.5 0.5 Input Leakage Current GND Vin VCC BERR, BR, BGACK, CLK, IPL2IPL0, AVEC,DSACK1, DSACK0, CDIS HALT, RESET Freescale Semiconductor, Inc... Hi-Z (Off-State) Leakage Current @ 2.4 V/0.5 V mA I in A31A0, AS, DBEN, DS, D31D0, FC2FC0, R/W, RMC, SIZ1SIZ0 I TSI Output High Voltage I OH = 400 mA A31A0, AS, BG, D31D0, DBEN, DS, R/W, ECS, IPEND, RMC, SIZ1SIZ0, FC2FC0 VOH Output Low Voltage I OL = 3.2 mA I OL = 5.3 mA I OL = 2.0 mA I OL = 10.7 mA A31A0, FC2FC0, SIZ1SIZ0, BG, D310 AS, DS, R/W, RMC, DBEN, IPEND, ECS, OCS HALT, RESET mA V V VOL Power Dissipation (TA = 0C) PD N 2.0 W Capacitance (see Note) Vin = 0 V, TA = 25uC, f = 1 MHz Cin N 20 pF CL N N 50 130 pF Load Capacitance ECS, OCS All Other NOTE: Capacitance is periodically sampled rather than 100% tested. 10.2.2 MC68EC020 Thermal Characteristics and DC Electrical Characteristics MC68EC020 Thermal Resistance (C/W) The following table provides thermal resistance characteristics for junction to ambient and junction to case for the MC68EC020 packages with natural convection and no heatsink. Characteristic Natural Convection and No Heatsink Thermal Resistance PPGA Package (RP Suffix) PQFP Package (FG Suffix) q JA q JC 32 53 10 18 MC68EC020 PQFP Package Table 10-4 provides typical and worst case thermal characteristics for the MC68EC020 PQFP package without a heatsink. Table 10-4. qJA vs. AirflowNMC68EC020 PQFP Package Airflow in Linear Feet/Minute q JA 0* 50 100 200 300 400 MaximumNNo Heatsink 53 49 45 41 38 36 TypicalNNo Heatsink 51 47 43 39 37 35 10-4 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. MC68EC020 DC Electrical Characteristics (VCC = 5.0 Vdc 5%; GND = 0 Vdc; Temperature within defined ranges) Characteristics Symbol Min Max Unit Input High Voltage VIH 2.0 VCC V Input Low Voltage VIL GND 0.5 0.8 V 1.0 20 1.0 20 20 20 2.4 N N N N 0.5 0.5 0.5 PINT N N 1.5 1.2 W Capacitance (see Note) Vin = 0 V, TA = 25uC, f = 1 MHz Cin N 20 pF Load Capacitance CL N 130 pF BERR, BR, CLK, IPL2IPL0, AVEC,DSACK1, DSACK0, CDIS, HALT, RESET Input Leakage Current GND Vin VCC A23A0, AS, DS, D31D0, FC2FC0, R/W, RMC, SIZ1SIZ0 I TSI Output High Voltage I OH = 400 mA A23A0, AS, BG, D31D0, DS, R/W, RMC, SIZ1SIZ0, FC2FC0 VOH Output Low Voltage I OL = 3.2 mA I OL = 5.3 mA I OL = 10.7 mA A23A0, FC2FC0, SIZ1SIZ0, BG, D31D0 AS, DS, R/W, RMC, HALT, RESET Freescale Semiconductor, Inc... Hi-Z (Off-State) Leakage Current @ 2.4 V/0.5 V mA I in mA V V VOL Power Dissipation (TA = 0C) f = 25 MHz f = 16 MHz NOTE: Capacitance is periodically sampled rather than 100% tested. 10.3 AC ELECTRICAL CHARACTERISTICS The AC specifications presented consist of output delays, input setup and hold times, and signal skew times. All signals are specified relative to an appropriate edge of the clock and possibly to one or more other signals. The measurement of the AC specifications is defined by the waveforms shown in Figure 10-1. To test the parameters guaranteed by Motorola, inputs must be driven to the voltage levels specified in Figure 10-1. Outputs are specified with minimum and/or maximum limits, as appropriate, and are measured as shown in Figure 10-1. Inputs are specified with minimum setup and hold times, and are measured as shown. Finally, the measurement for signal-to-signal specifications is also shown. Note that the testing levels used to verify conformance to the AC specifications do not affect the guaranteed DC operation of the device as specified in the DC electrical specifications. The 20 MHz and 33.33 MHz specifications do not apply to the MC68EC020. MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-5 Freescale Semiconductor, Inc. DRIVE TO 2.4 V 2.0 V 2.0 V CLK 0.8 V A DRIVE TO 0.5 V OUTPUTS1 CLK 0.8 V B VALID OUTPUT n 2.0 V 2.0 V 0.8 V 0.8 V VALID OUTPUT A n+1 B VALID OUTPUT n Freescale Semiconductor, Inc... OUTPUTS 2 CLK C DRIVE TO 2.4 V INPUTS3 CLK DRIVE TO 0.5 V 2.0 V 0.8 V 2.0 V 2.0 V 0.8 V 0.8 V D 2.0 V VALID INPUT 0.8 V C 2.0 V INPUTS 4 CLK 0.8 V ALL SIGNALS 5 VALID OUTPUT n+1 D VALID INPUT DRIVE TO 2.4 V 2.0 V 0.8 V DRIVE TO 0.5 V 2.0 V 0.8 V E F 2.0 V 0.8 V NOTES: 1. This output timing is applicable to all parameters specified relative to the rising edge of the clock. 2. This output timing is applicable to all parameters specified relative to the falling edge of the clock. 3. This input timing is applicable to all parameters specified relative to the rising edge of the clock. 4. This input timing is applicable to all parameters specified relative to the falling edge of the clock. 5. This timing is applicable to all parameters specified relative to the assertion/negation of another signal. LEGEND: A. Maximum output delay specification. B. Minimum output hold time. C. Minimum input setup time specification. D. Minimum input hold time specification. E. Signal valid to signal valid specification (maximum or minimum). F. Signal valid to signal invalid specification (maximum or minimum). FIGURE 10-1 MC68020UM Figure 10-1. Drive Levels and Test Points for AC Specifications 10-6 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. AC ELECTRICAL CHARACTERISTICSNCLOCK INPUT (see Figure 10-2) 16.67 MHz Num. Characteristic Min Frequency of Operation 1 8 25 MHz* 20 MHz Max Min 16.67 12.5 Max Min Max 20 12.5 25 33.33 MHz Min Max Unit 12.5 33.33 MHz Cycle Time 60 125 50 80 40 80 30 80 ns 2,3 Clock Pulse Width (Measured from 1.5 V to 1.5 V) 24 95 20 54 19 61 14 66 ns 4,5 Clock Rise and Fall Times N 5 N 5 N 4 N 3 ns *These specifications represent an improvement over previously published specifications for the 25-MHz MC68020 and Freescale Semiconductor, Inc... are valid only for products bearing date codes of 8827 and later. 1 2 3 2.0 V 0.8 V 4 5 NOTE:Timing measurements are referenced to and from a low voltage of .08 V and a high voltage of 2.0 V, unless othervise noted. The voltage swing through this r should start outside and pass through the range such that the rise or fall between 0.8 V and 2.0 V. a w FIGURE 10-2 MC68020UM Figure 10-2. Clock Input Timing Diagram MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-7 Freescale Semiconductor, Inc. AC ELECTRICAL CHARACTERISTICSNREAD AND WRITE CYCLES (VCC = 5.0 Vdc 5%; GND = 0 V dc; Temperature within defined ranges; see Figures 10-310-5) 16.67 MHz 25 MHz** 33.33 MHz Num. Characteristics Min Max Min Max Min Max Min Max Unit 6 Clock High to FC, Size, RMC, Address Valid 0 30 0 25 0 25 0 21 ns Clock High to ECS, OCS Asserted 0 20 0 15 0 12 0 10 ns 7 Clock High to Address, Data, FC, Size, RMC High Impedance 0 60 0 50 0 40 0 30 ns 8 Clock High to Address, FC, Size, RMC Invalid 0 N 0 N 0 N 0 N ns 9 Clock Low to AS, DS Asserted 3 30 3 25 3 18 3 15 ns AS to DS Assertion Skew (Read) 15 15 10 10 10 10 10 10 ns AS Asserted to DS Asserted (Write) 37 N 32 N 27 N 22 N ns *10 ECS Width Asserted 20 N 15 N 15 N 10 N ns *10A OCS Width Asserted 20 N 15 N 15 N 10 N ns 15 N 10 N 5 N 5 N ns 15 N 10 N 6 N 5 N ns *6A 9A1 Freescale Semiconductor, Inc... 20 MHz 9B11 *10B7 ECS, OCS Width Negated 11 Address, FC, Size, RMC Valid to AS (and DS Asserted, Read) 12 Clock Low to AS, DS Negated 0 30 0 25 0 15 0 15 ns Clock Low to ECS, OCS Negated 0 30 0 25 0 15 0 15 ns *12A 13 AS, DS Negated to Address, FC, Size, RMC Invalid 15 N 10 N 10 N 5 N ns 14 AS (and DS Read) Width Asserted 100 N 85 N 70 N 50 N ns DS Width Asserted (Write) 40 N 38 N 30 N 25 N ns AS, DS Width Negated 40 N 38 N 30 N 23 N ns DS Negated to AS Asserted 35 N 30 N 25 N 18 N ns 16 Clock High to AS, DS, R/W, DBEN High Impedance N 60 N 50 N 40 N 30 ns 17 AS, DS Negated to R/W Invalid 15 N 10 N 10 N 5 N ns 18 Clock High to R/W High 0 30 0 25 0 20 0 15 ns 20 Clock High to R/W Low 0 30 0 25 0 20 0 15 ns 21 R/W High to AS Asserted (Read) 15 N 10 N 5 N 5 N ns 22 R/W Low to DS Asserted (Write) 75 N 60 N 50 N 35 N ns 23 Clock High to Data-Out Valid N 30 N 25 N 25 N 18 ns 25 AS, DS Negated to Data-Out Invalid 15 N 10 N 5 N 5 N ns *25A9 DS Negated to DBEN Negated (Write) 15 N 10 N 5 N 5 N ns 26 Data-Out Valid to DS Asserted (Write) 15 N 10 N 5 N 5 N ns 27 Data-In Valid to Clock Low (Setup) (Read) 5 N 5 N 5 N 5 N ns 20 N 15 N 10 N 5 N ns 0 80 0 65 0 50 0 40 ns 14A 15 15A8 27A 28 10-8 Late BERR/HALT Asserted to Clock Low (Setup) AS, DS Negated to DSACK, BERR, HALT, AVEC Negated M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. AC ELECTRICAL CHARACTERISTICSNREAD AND WRITE CYCLES (Continued) 16.67 MHz Num. 33.33 MHz Max Min Max Min Max Min Max Unit AS, DS Negated to Data-In Invalid (Data-In Hold Time) 0 N 0 N 0 N 0 N ns AS, DS Negated to Data-In (High Impedance) N 60 N 50 N 40 N 30 ns 30 Clock Low to Data-In Invalid (Data-In Hold Time) 15 N 15 N 10 N 10 N ns 312 DSACK Asserted to Data-In Valid N 50 N 43 N 32 N 17 ns DSACK Asserted to DSACK Valid (DSACK Asserted Skew) N 15 N 10 N 10 N 10 ns 32 RESET Input Transition Time N 1.5 N 1.5 N 1.5 N 1.5 Clks 33 Clock Low to BG Asserted 0 30 0 25 0 20 0 20 ns 34 Clock Low to BG Negated 0 30 0 25 0 20 0 20 ns 35 BR Asserted to BG Asserted (RMC Not Asserted) 1.5 3.5 1.5 3.5 1.5 3.5 1.5 3.5 Clks *37 BGACK Asserted to BG Negated 1.5 3.5 1.5 3.5 1.5 3.5 1.5 3.5 Clks *37A6 BGACK Asserted to BR Negated 0 1.5 0 1.5 0 1.5 0 1.5 Clks 29A 31A3 Freescale Semiconductor, Inc... 25 MHz** Min 29 Characteristics 20 MHz 39 BG Width Negated 90 N 75 N 60 N 50 N ns 39A BG Width Asserted 90 N 75 N 60 N 50 N ns *40 Clock High to DBEN Asserted (Read) 0 30 0 25 0 20 0 15 ns *41 Clock Low to DBEN Negated (Read) 0 30 0 25 0 20 0 15 ns *42 Clock Low to DBEN Asserted (Write) 0 30 0 25 0 20 0 15 ns *43 Clock High to DBEN Negated (Write) 0 30 0 25 0 20 0 15 ns *44 R/W Low to DBEN Asserted (Write) 15 N 10 N 10 N 5 N ns *455 DBEN Width Asserted 60 120 N N 50 100 N N 40 80 N N 30 60 N N ns Read Write 46 R/W Width Valid (Write or Read) 150 N 125 N 100 N 75 N ns 47A Asynchronous Input Setup Time 5 N 5 N 5 N 5 N ns 47B Asynchronous Input Hold Time 15 N 15 N 10 N 10 N ns 484 DSACK Asserted to BERR, HALT Asserted N 30 N 20 N 18 N 15 ns 53 Data-Out Hold from Clock High 0 N 0 N 0 N 0 N ns 55 R/W Valid to Data Bus Impedance Change 30 N 25 N 20 N 20 N ns 56 RESET Pulse Width (Reset Instruction) 512 N 512 N 512 N 512 N Clks 57 BERR Negated to HALT Negated (Rerun) 0 N 0 N 0 N 0 N ns *5810 BGACK Negated to Bus Driven 1 N 1 N 1 N 1 N Clks 5910 BG Negated to Bus Driven 1 N 1 N 1 N 1 N Clks *This specification does not apply to the MC68EC020. **These specifications represent an improvement over previously published specifications for the 25-MHz MC68020 and are valid only for product bearing date codes of 8827 and later. MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-9 Freescale Semiconductor, Inc. AC ELECTRICAL CHARACTERISTICSNREAD AND WRITE CYCLES Freescale Semiconductor, Inc... (Concluded) NOTES: 1. This number can be reduced to 5 ns if strobes have equal loads. 2. If the asynchronous setup time (#47A) requirements are satisfied, the DSACK low to data setup time (#31) and DSACK low to BERR low setup time (#48) can be ignored. The data must only satisfy the data-in clock low setup time (#27) for the following clock cycle, and BERR must only satisfy the late BERR low to clock low setup time (#27A) for the following clock cycle. 3. This parameter specifies the maximum allowable skew between DSACK0 to DSACK1 asserted or DSACK1 to DSACK0 asserted; specification #47A must be met by DSACK0 or DSACK1. 4. This specification applies to the first (DSACK0 or DSACK1) DSACK signal asserted. In the absence of DSACK, BERR is an asynchronous input using the asynchronous input setup time (#47A). 5. DBEN may stay asserted on consecutive write cycles. 6. The minimum values must be met to guarantee proper operation. If this maximum value is exceeded, BG may be reasserted. 7. This specification indicates the minimum high time for ECS and OCS in the event of an internal cache hit followed immediately by a cache miss or operand cycle. 8. This specification guarantees operation with the MC68881/MC68882, which specifies a minimum time for DS negated to AS asserted (specification #13A in MC68881UM/AD, MC68881/MC68882 Floating-Point Coprocessor User's Manual). Without this specification, incorrect interpretation of specifications #9A and #15 would indicate that the MC68020/EC020 does not meet the MC68881/MC68882 requirements. 9. This specification allows a system designer to guarantee data hold times on the output side of data buffers that have output enable signals generated with DBEN. 10. These specifications allow system designers to guarantee that an alternate bus master has stopped driving the bus when the MC68020/EC020 regains control of the bus after an arbitration sequence. 11. This specification allows system designers to qualify the CS signal of an MC68881/MC68882 with AS (allowing 7 ns for a gate delay) and still meet the CS to DS setup time requirement (specification 8B of MC68881UM/AD, MC68881/MC68882 Floating-Point Coprocessor User's Manual). 10-10 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 CLK 6 7 *A31-A0 FC2-FC0 SIZ1-SIZ0 12A 8 10 **ECS 6A OCS Freescale Semiconductor, Inc... 16 10A 14 13 AS 11 12 DS 18 9 R/W 46 21 17 DSACK0 31A 28 DSACK1 29A 31 D31-D0 27 29 30 **DBEN 45 BERR 41 40 27A HALT 48 ALL ASYNCHRONOUS INPUTS 47A 47B *For the MC68EC020, A23A0. **This signal does not apply to the MC68EC020. NOTE: Timing measurements are referenced to and from a low voltage of 0.8 V and a high voltage of 2.0 V, unless otherwise noted. The voltage swing through this range should start outside and pass through the range such that the rise or fall will be linear between 0.8 V and 2.0 V. FIGURE 10-3 MC68020UM Figure 10-3. Read Cycle Timing Diagram MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-11 Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 CLK 7 6 *A31-A0 FC2-FC0 10 SIZ1-SIZ0 8 12A Freescale Semiconductor, Inc... **ECS 6A 10A **OCS 13 11 AS 14 15 9 14A DS 20 12 22 R/W 9 17 46 DSACK0 31A 28 55 DSACK1 23 53 D31-D0 44 26 25 25A **DBEN 45 BERR 43 42 48 HALT *For the MC68EC020, A23A0. **This signal does not apply to the MC68EC020. 27A NOTE: Timing measurements are referenced to and from a low voltage of 0.8 V and a high voltage of 2.0 V, unless otherwise noted. The voltage swing through this range should start outside and pass through the range such that the rise or fall will be linear between 0.8 V and 2.0 V. FIGURE 10-4 MC68020UM Figure 10-4. Write Cycle Timing Diagram 10-12 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. S0 S1 S2 S3 S4 S5 CLK *A31-A0 D31-D0 FC2-FC0 SIZ1-SIZ0 Freescale Semiconductor, Inc... **ECS 58 7 OCS AS DS 59 R/W DBEN 16 DSACK0 DSACK1 33 35 BR 37A 34 BG 39 37 **BGACK 39A *For the MC68EC020, A23A0. **This signal does not apply to the MC68EC020. NOTE: Timing measurements are referenced to and from a low voltage of 0.8 V and a high voltage of 2.0 V, unless otherwise noted. The voltage swing through this range should start outside and pass through the range such that the rise or fall will be linear between 0.8 V and 2.0 V. FIGURE 10-5 MC68020UM Figure 10-5. Bus Arbitration Timing Diagram MOTOROLA M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com 10-13 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. 10-14 M68020 USEROS MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. SECTION 11 ORDERING INFORMATION AND MECHANICAL DATA Freescale Semiconductor, Inc... This section contains the pin assignments and package dimensions of the MC68020 and the MC68EC020. In addition, detailed information is provided to be used as a guide when ordering. 11.1 STANDARD ORDERING INFORMATION 11.1.1 Standard MC68020 Ordering Information Package Type Ceramic Pin Grid Array RC Suffix Plastic Quad Flat Pack FC Suffix Plastic Pin Grid Array RP Suffix Ceramic Quad Flat Pack FE Suffix Frequency (MHz) Temperature (C) Order Number 16.67 20.0 25.0 33.33 0 to 70 0 to 70 0 to 70 0 to 70 MC68020RC16 MC68020RC20 MC68020RC25 MC68020RC33 16.67 20.0 25.0 0 to 70 0 to 70 0 to 70 MC68020FC16 MC68020FC20 MC68020FC25 16.67 20.0 25.0 0 to 70 0 to 70 0 to 70 MC68020RP16 MC68020RP20 MC68020RP25 16.67 20.0 25.0 33.33 0 to 70 0 to 70 0 to 70 0 to 70 MC68020FE16 MC68020FE20 MC68020FE25 MC68020FE33 11.1.2 Standard MC68EC020 Ordering Information Package Type Plastic Pin Grid Array RP Suffix Plastic Quad Flat Pack FG Suffix MOTOROLA Frequency (MHz) Temperature (C) Order Number 16.67 25.0 0 to 70 0 to 70 MC68EC020RP16 MC68EC020RP25 16.67 25.0 0 to 70 0 to 70 MC68EC020FG16 MC68EC020FG25 MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-1 Freescale Semiconductor, Inc. 11.2 PIN ASSIGNMENTS AND PACKAGE DIMENSIONS 11.2.1 MC68020 RC and RP Suffix--Pin Assignment N D31 D28 D25 D22 D20 D17 GND VCC D14 D12 D9 D8 VCC DS D29 D26 D24 D21 D18 D16 VCC D13 D10 D6 D5 D4 AS R/W D30 D27 D23 D19 GND D15 D11 D7 GND D3 D2 M L K GND HALT GND D1 D0 J DSACK1 BERR GND IPL0 IPL1 H Freescale Semiconductor, Inc... CDIS AVEC DSACK0 IPL2 GND G MC68020 ECS SIZ1 DBEN VCC GND VCC F SIZ0 FC2 FC1 GND IPEND FC0 RMC VCC A2 OCS VCC VCC VCC A4 A3 A7 A5 E D C RESET CLK GND A0 A29 A25 A21 A17 A16 A12 A9 B GND BG BR A30 A27 A24 A20 A18 GND A15 A13 A10 A6 BGACK A1 A31 A28 A26 A23 A22 A19 VCC GND A14 A11 A8 A 1 2 3 4 5 6 7 8 9 10 11 12 13 The VCC and GND pins are separated into four groups to provide individual power supply connections for the address bus buffers, data bus buffers, and all other output buffers and internal logic. It is recommended that all pins be connected to power and ground as indicated. Group 13-2 Address Bus VCC A9, D3 GND A10, B9, C3, F12 Data Bus M8, N8, N13 L7, L11, N7, K3 Logic D1, D2, E3, G11, G13 G12, H13, J3, K1 Clock -- B1 MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 11.2.2 MC68020 RC Suffix--Package Dimensions RC SUFFIX CASE 791-01 MC68020 T K G N M L K J H G F E D C B A Freescale Semiconductor, Inc... A G 1 2 3 4 5 6 7 8 9 10 11 12 13 B MILLIMETERS DIM A B C D G K MIN 34.04 34.04 2.54 0.43 MAX 35.05 35.05 3.81 0.55 2.54 BSC 4.32 4.95 MOTOROLA C INCHES MIN 1.340 1.340 0.100 0.017 MAX 1.380 1.380 0.150 0.022 D NOTES: 1. A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. POSITIONAL TOLERANCE FOR LEADS (114 PLACES). 0.13 (0.005) M T A S B S 3. DIMENSIONING AND TOLERANCING PER Y14.5M,1982. 4. CONTROLLING DIMENSION: INCH. 0.100 BSC 0.170 0.195 MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-3 Freescale Semiconductor, Inc. 11.2.3 MC68020 RP Suffix--Package Dimensions RP SUFFIX CASE 789E-02 MC68020 T X V Freescale Semiconductor, Inc... K N M L K J H G F E D C B A A L C G V 1 2 3 4 5 6 7 8 9 10 11 12 13 PIN A-1 B G D 114 PL 0.76 (0.030) 0.25 (0.010) M T A S B S M X 0.17 (0.007) M T MILLIMETERS DIM A B C D G K L V 13-4 MIN 34.04 34.04 MAX 35.05 35.05 2.92 3.18 0.44 0.55 2.54 BSC 3.81 2.79 1.02 1.52 30.48 BSC INCHES MIN MAX 1.340 1.380 1.340 1.380 0.115 0.017 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION D INCLUDES LEAD FINISH. 4. 789E-01 OBSOLETE. NEW STANDARD 789E-02. 0.135 0.022 0.100 BSC 0.110 0.150 0.040 0.060 1.200 BSC MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. NC* BGACK R/W NC* DS GND GND HALT AS GND GND DSACK0 DSACK1 BERR CDIS AVEC DBEN ECS FC2 SIZ0 SIZ1 FC0 FC1 RMC CLK RESET VCC VCC GND GND BG VCC NC* NC* GND 11.2.4 MC68020 FC and FE Suffix--Pin Assignment 1 132 17 18 BR A30 A29 A28 A27 A26 A25 A24 A23 A22 A21 A20 TOP VIEW 34 A19 A18 A17 VCC VCC GND GND A16 A15 A14 A13 A12 A11 A10 NC* NC* 50 67 Group MOTOROLA Address Bus VCC 13, 38, 39 15, 40, 41, 62 Data Bus 79, 80, 96, 97 77, 78, 98, 99, 119, 120 Logic 7, 8, 65, 66 67, 68, 124, 125 Clock -- 11, 12 NC* NC* VCC D5 GND GND VCC D3 D4 IPL1 IPL0 D0 D1 D2 GND GND IPL2 OCS IPEND V CC V CC GND A5 A4 A3 A2 A8 A7 A6 NC* NC* A9 The VCC and GND pins are separated into four groups to provide individual power supply connections for the address bus buffers, data bus buffers, and all other output buffers and internal logic. It is recommended that all pins be connected to power and ground as indicated. NC pins are reserved by Motorola for future use and should have no external connection. NC* Freescale Semiconductor, Inc... A0 A1 A31 GND MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-5 Freescale Semiconductor, Inc. 11.2.5 MC68020 FC Suffix--Package Dimensions FC SUFFIX CASE 831A-01 MC68020 N 0.25 (0.010) S T X 0.05 (0.002) Y S S Z S S 0.20 (0.008) S T X Y S ZS S A Z PIN 1 INDE V B L R Freescale Semiconductor, Inc... G Y X P 0.20 (0.008) S T X 0.25 (0.010) S T 0.05. (0.002) X S Y S Z S P Y Z S S S H C .10 (0.004) T J SEATING PLANE D 132 PL 0.20 (0.008) S T X S Y S Z S K SECTION P-P DIM A B C D G H J K 13-6 MILLIMETERS MIN MAX 24.06 24.20 24.06 24.20 4.07 4.57 0.21 0.30 0.64 BSC 0.51 1.01 0.16 0.20 INCHES MIN MAX 0.947 0.953 0.947 0.953 0.160 0.180 0.008 0.012 0.025 BSC 0.020 0.040 0.006 0.008 0.030 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH 3. DIMENSIONS A, B, N, AND R DO NOT INCLUDE MOLD PROTRUSION ALLOWABLE MOLD PROTRUSION FOR DIMENSIONS A AND B IS 0.25 (0.010), FOR DIMENSIONS N AND R IS 0.18 (0.007). 4. DATUM PLANE -W- IS LOCATED AT THE UNDERSIDE OF LEADS WHERE LEADS EXIT PACKAGE BODY. 5. DATUMS -X-, -Y-, AND -Z- TO BE DETERMINED WHERE CENTER LEA PACKAGE BODY AT DATUM -W-. MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 11.2.6 MC68020 FE Suffix--Package Dimensions FE SUFFIX CASE 831-01 MC68020 S 0.20 (0.008) M T X S --Y S ZS A Freescale Semiconductor, Inc... 0.51 (0.020) V M T X S --Y S Z S PIN 1 INDENT B L X 0.51 (0.020) 0.20 (0.008) M M T X S --Y S T X S --Y S ZS Z S R J W 0.10 (0.004) T SEATING PLANE C M D 132 PL 0.20 (0.008) DIM A B C D G H J K L M R MOTOROLA H MILLIMETERS MIN MAX 21.85 22.86 21.85 22.86 3.94 4.31 0.204 0.292 0.64 BSC 0.64 0.88 0.13 0.20 0.51 0.76 20.32 REF 0 8 -- 0.64 INCHES MAX MIN 0.860 0.900 0.860 0.900 0.155 0.170 0.0080 0.0115 0.025 BSC 0.025 0.035 0.005 0.008 0.020 0.030 0.800 REF 0 8 -- 0.025 M T X S --Y S ZS K NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH 3. DIMENSIONS A AND B DEFINE MAXIMUM CERAMIC BODY DIMENSIONS INCLUDING GLASS PROTRUSION AND MISMATCH OF CERAMIC BODY TOP AND BOTTOM. 4. DATUM PLANE -W- IS LOCATED AT THE UNDERSIDE OF LEADS WHERE LEADS EXIT PACKAGE BODY. 5. DATUMS -X-, -Y-, AND -Z- TO BE DETERMINED WHERE CENTER LEADS EXIT PACKAGE BODY AT DATUM -W-. 6. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM -T-. 7. DIMENSIONS A AND B TO BE DETERMINED AT DATUM PLANE -W-. MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-7 Freescale Semiconductor, Inc. 11.2.7 MC68EC020 RP Suffix--Pin Assignment N D31 D29 D28 D26 D24 D22 D19 D16 VCC D15 D13 D11 D10 GND D30 D27 D25 D23 D21 D18 GND V CC D14 D12 D9 D8 DS R/W D20 D17 GND D6 D7 HALT AS VCC D5 GND GND D4 GND D1 D2 D3 M L K J Freescale Semiconductor, Inc... H DSACK0 DSACK1 BERR MC68EC020 G (BOTTOM VIEW) SIZ1 CDIS AVEC IPL1 IPL0 D0 FC2 SIZ0 GND GND IPL2 RMC FC1 V CC V CC V CC V CC A2 GND CLK RESET A4 A3 GND BG A0 A23 GND BR A1 1 2 3 F E FC0 D C A19 V CC GND A21 A18 V CC A16 A14 A12 A10 A7 A5 A22 A20 A17 GND A15 A13 A11 A9 A8 A6 4 5 6 7 8 9 10 11 12 13 B A The VCC and GND pins are separated into four groups to provide individual power supply connections for the address bus buffers, data bus buffers, and all other output buffers and internal logic. It is recommended that all pins be connected to power and ground as indicated. Group 13-8 Address Bus VCC B7, C7 GND A1, A7, C8, D13 Data Bus K12, M9, N9 J13, L8, M1, M8 Logic D1, D2, E12, E13 F11, F12, J1, J2 Clock -- B1 MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 11.2.8 MC68EC020 RP Suffix--Package Dimensions RP SUFFIX CASE 789H-01 MC68EC020 T X V Freescale Semiconductor, Inc... S N M L K J H G F E D C B A A PIN A-1 B G K L C G V 1 2 3 4 5 6 7 8 9 10 11 12 13 D 100 PL 0.76 (0.030) 0.25 (0.010) M T A S M B S X 0.17 (0.007) M T MILLIMETERS DIM A B C D G K L S V MIN 34.04 34.04 MAX 35.05 35.05 2.92 3.18 0.44 0.55 2.54 BSC 3.55 3.05 1.02 1.52 4.32 4.83 30.48 BSC MOTOROLA INCHES MIN MAX 1.340 1.380 1.340 1.380 0.115 0.017 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH 3. DIMENSION D INCLUDES LEAD FINISH. 0.135 0.022 0.100 BSC 0.120 0.140 0.040 0.060 0.170 0.190 1.200 BSC MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-9 Freescale Semiconductor, Inc. 80 A9 D9 NC* D8 D6 D7 VCC D5 GND D4 GND D2 D3 IPL0 D0 D1 IPL1 IPL2 GND GND GND VCC VCC A2 A4 A3 A5 A6 A7 A8* NC 11.2.9 MC68EC020 FG Suffix--Pin Assignment 51 50 81 A10 D10 D11 A11 D12 A12 D13 A13 D14 D15 VCC A14 A16 GND GND D16 VCC A17 MC68EC020 (TOP VIEW) D17 D18 A18 A19 D19 D20 A20 A21 D21 D22 A22 D23 A23 A1 D24 D26 100 31 1 D27 D29 D30 D31 GND DS R/W AS GND HALT GND BERR DSACK1 DSACK0 AVEC CDIS SIZ1 FC2 SIZ0 FC1 FC0 RMC RESET VCC VCC CLK GND GND 30 D28 A0 GND D25 BR BG Freescale Semiconductor, Inc... A15 *NC--Do not connect to this pin. The VCC and GND pins are separated into four groups to provide individual power supply connections for the address bus buffers, data bus buffers, and all other output buffers and internal logic. It is recommended that all pins be connected to power and ground as indicated. NC pins are reserved by Motorola for future use and should have no external connection. Group 13-10 Address Bus VCC 90 GND 72, 89, 100 Data Bus 44, 57 26, 43, 58, 59 Logic 7, 8, 70, 71 3, 20, 21, 68, 69 Clock -- 4 MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. 11.2.10 MC68EC020 FG Suffix--Package Dimensions Y AA H A-B S D S 80 81 50 M B A 0.20 (0.008) M B L 0.20 (0.008) 0.05 (0.002) V DETAIL "A" 100 31 P 1 Z 30 D F A A, B, D 0.20 (0.008) M C A - B S 0.50 (0.002) A - B DETAIL "A" D S H A-B S M N J S 0.20 (0.008) BASE METAL D S D M C A-B T 0.20 (0.008) R DATUM PLANE C U Freescale Semiconductor, Inc... 51 C A-B S D S D FG SUFFIX CASE 842D-01 MC68EC020 H DETAIL "C" M E Q DETAIL "C DATUM PLANE 0.10 (0 H K C X DIM A B C D E F G H J K L M N P Q R S T U V MOTOROLA SEATING PLANE MILLIMETERS MIN MAX 19.90 20.10 13.90 14.10 -- 3.30 0.22 0.38 2.55 3.05 0.22 0.33 0.65 BSC 0.10 0.36 0.13 0.23 0.65 0.95 12.35 REF 5 16 0.13 0.17 0.325 BSC 0 7 0.25 0.35 23.65 24.15 -- 0.13 -- 0 17.65 18.15 INCHES MIN MAX 0.783 0.791 0.547 0.555 -- 0.130 0.009 0.015 0.100 0.120 0.009 0.013 0.026 BSC 0.004 0.014 0.005 0.009 0.026 0.037 0.486 REF 5 16 0.005 0.007 0.013 BSC 0 7 0.010 0.014 0.931 0.951 -- 0.005 -- 0 0.695 0.715 H G DETAIL "B" M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS -A-, -B-, AND -D- TO BE DETERMINED AT DATUM PLANE -H-. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -C-. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWA PROTRUSION IS 0.25 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUD MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABL DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MC68838 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com 13-11 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... APPENDIX A INTERFACING AN MC68EC020 TO A DMA DEVICE THAT SUPPORTS A THREE-WIRE BUS ARBITRATION PROTOCOL The MC68EC020 supports a two-wire bus arbitration protocol; however, it may become necessary to interface the MC68EC020 to a device that supports a three-wire arbitration protocol. Figure A-1 shows a method by which this can be achieved. BR BR MC68EC020 BG BG DMA BGACK 74LS08 BGACK (DMA) BR (MC68EC020) 74LS04 4 PR BR (DMA) D 74LS04 BG (MC68EC020) Q 74F74 CLK BG (DMA) Q CLR +5 V Figure A-1. Bus Arbitration Circuit-- MC68EC020 (Two-Wire) to DMA (Three-Wire) MOTOROLA M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com A-1 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... INDEX -- A-- A1, A0 Signals, 5-2, 5-7, 5-9, 5-21, 9-5 A15-A13 Signals, 7-6 A19-A16 Signals, 7-6 A31-A24 Signals, 4-1, 5-3 AC Specifications, 10-5 Access Level, 9-17 Access Time Calculations, 9-12 Address Bus, 3-2, 5-3, 5-25 Address Error Exception, 5-14, 6-6 Address Registers, 1-4 Address Space, 2-4, 5-3 Addressing Modes, 1-8 Arithmetic/Logical Instruction, 8-30, 8-31 AS Signal, 3-4, 5-2, 5-3 Autovector, 5-48 Autovector Interrupt Acknowledge Cycle, 5-48 AVEC Signal, 3-5, 5-4, 5-48, 5-53 -- B-- BERR Signal, 3-7, 5-4, 5-25, 5-53, 5-55, 6-4 BG Signal, 3-6, 5-63, 5-66, 5-70 BGACK Signal, 3-6, 5-62, 5-63, 5-66 Binary-Coded Decimal, 8-32 Bit Field Manipulation Instructions, 8-36 Bit Manipulation Instructions, 8-35 BKPT Instruction, 5-50 Flowchart, 6-17 Block Diagram, 1-2 BR Signal, 3-6, 5-63, 5-66, 5-70, 5-71 Breakpoint Acknowledge Cycle, 5-50, 6-17 Flowchart, 5-50 Timing, 5-50 Breakpoint Instruction Exception, 6-17 Bus, 5-24 Arbitration, 5-62 Cycles, 5-1 Master, 5-1 Operation, 5-1, 5-24 Bus Arbitration (MC68020), 5-63 MOTOROLA Control Unit, 5-67 Flowchart, 5-63 Read-Modify-Write, 5-68 Timing, 5-63 Bus Arbitration (MC68EC020), 5-70 Control Unit, 5-73 Flowchart, 5-70 Timing, 5-70 Two-Wire, 5-75, A-1 Bus Controller, 5-22, 8-2, 8-5 Bus Cycles, 5-1, 5-25 Bus Error Exception, 6-4, 6-21 Bus Fault, 6-21 Bus Master, 5-1, 5-25, 5-62 Bus Operation, 5-24 Byte Enable Signals, 5-21 Byte Select Control Signals, 9-5 -- C-- Cache, 1-13, 4-1, 5-2, 5-22, 5-62, 8-1, 8-7, 9-11 Control, 4-3 Internal Cache Holding Register, 5-21 Reset, 4-3 Cache Address Register (CAAR), 1-7, 4-3, 4-4 Cache Control Register (CACR), 1-7, 4-2, 4-3 CALLM Instruction, 9-14, 9-16, 9-18 CAS Instruction, 5-39 CAS2 Instruction, 5-39 CDIS Signal, 3-7, 4-3 CLK Signal, 3-7 Clock Drivers, 9-10 Condition Codes, 1-7 Conditional Branch Instructions, 8-37 Control Instructions, 8-38 Coprocessor, 6-25, 7-1 Classification, 7-4 Communication Protocol, 7-4 Conditional Instruction Category, 7-10 Coprocessor Context Restore Instruction Category, 7-22 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com INDEX-1 Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. Coprocessor Context Save and Context Restore Instruction Categories, 7-16 Coprocessor Context Save Instruction Category, 7-20 Coprocessor General Instruction Category, 7-8 Coprocessor Instructions, 7-1, 7-7 Format Words, 7-18 Instruction, 6-25, 7-3 Instruction Execution, 7-6 Coprocessor Detected Data-Processing-Related Exceptions, 7-51 Exception, 7-49 Format Errors, 7-52 Illegal Coprocessor Command or Condition Words, 7-51 Protocol Violation Exceptions, 7-50 System-Related Exceptions, 7-51 Coprocessor Instruction, 6-25, 7-3 Coprocessor Interface, 5-53, 7-1, 7-2 Coprocessor Interface Register (CIR), 7-4, 7-5, 7-6, 7-24 Command CIR, 7-25 Condition CIR, 7-26 Control CIR, 7-24 Instruction Address CIR, 7-27 Memory Map, 7-24 Operand Address CIR, 7-27 Operand CIR, 7-26 Operation Word CIR, 7-25 Register Select CIR, 7-27 Response CIR, 7-24 Restore CIR, 7-25 Save CIR, 7-25 Selection, 7-6 CPU Address Space, 2-4, 5-44, 7-6 CPU Space Type, 5-44, 5-53 Cycle Asynchronous Cycles, 5-1, 5-5 Autovector Interrupt Acknowledge Cycle, 5-45, 5-48 Breakpoint Acknowledge Cycle, 5-50 Coprocessor Interface Bus Cycles, 7-4 Interrupt Acknowledge Cycle, 5-4, 5-45 Operand Transfer Cycle, 5-5 Synchronous Cycle, 5-24 INDEX-2 -- D-- Data Accesses, 4-2 Data Bus (D31-D0), 3-2, 5-3, 5-5, 5-21, 5-25 Data Registers, 1-4 Data Types, 1-8 DBEN Signal, 3-5, 5-4 DC Electrical Characteristics MC68020, 10-4 MC68EC020, 10-5 Destination Function Code Register (DFC), 1-7 Differences between MC68020 and MC68EC020, 1-1, 5-62 Double Bus Fault, 5-60 DS Signal, 3-4, 5-4, 5-21 DSACK1, DSACK0 Signals, 3-5, 5-4, 5-5, 5-24, 5-46, 5-53, 9-5 Dynamic Bus Sizing, 5-5 -- E-- ECS Signal, 3-4, 5-3 Effective Address, 8-13, 8-14, 8-16, 8-17, 8-19 Electrical Specifications, 10-1 Exception, 2-5, 7-57 Address Error Exception, 5-14, 6-6, 7-57 Breakpoint Instruction, 6-17 Bus Error Exception, 6-4, 6-21 Coprocessor-Detected Exception, 7-49 cpTRAPcc Instruction Traps, 7-55 Data-Processing-Related Exception, 7-51 F-Line Emulator Exception, 7-54 Format Error Exception, 6-10, 7-57 Illegal Instruction, 6-7 Interrupt Exception, 5-45, 6-11, 7-56 Multiple, 6-17 Privilege Violation Exception, 6-7, 6-8, 7-55 Protocol Violation, 7-50 Reset Exception, 6-4 Stack Frames, 6-25 System-Related Exception, 7-51 Trace Exception, 6-9, 7-55 Trap Exception, 6-6 Unimplemented Instruction, 6-7 Exception Handler, 6-2 Exception Processing, 2-1, 2-5, 6-1 Exception-Related Instructions, 8-39 Exception Stack Frame, 2-6, 6-25 Exception Vector Table, 2-5, 6-2 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc... Freescale Semiconductor, Inc. -- F-- FC2-FC0 Signals, 2-2, 2-4, 3-2, 5-2, 5-3, 5-44, 7-6 Features, 1-2 F-Line Operation Words, 7-3 Floating-Point Coprocessor, 7-1, 9-1 Flowchart Breakpoint Acknowledge Cycle, 5-50 Byte Read Cycle, 5-26 Interrupt Acknowledge Cycle, 5-46 Long-Word Read Cycle, 5-26 MC68EC020 Bus A rbitration, 5-70 MC68020 Bus A rbitration, 5-63 Read-Modify-Write Cycle, 5-39 Reset Exception, 6-4 Write Cycle, 5-33 Format Error Exception, 6-10 -- G-- Ground Connections, 3-7, 9-9 -- H-- HALT Signal, 3-7, 5-4, 5-25, 5-53, 5-60 -- I-- Idle Clock Cycles, 8-7 Illegal Instruction Exception, 6-7 Instruction Arithmetic/Logical, 8-30, 8-31 Bcc, 8-37 Bit Field Manipulation, 8-36 Bit Manipulation, 8-35 BKPT, 5-50 CALLM, 9-14, 9-16, 9-18 CAS, 5-39 CAS2, 5-39 Control, 8-38 Coprocessor Conditional Instructions, 7-10 Coprocessor Context Restore Instruction Category, 7-22 Coprocessor Context Save Instruction Category, 7-20 Coprocessor Instruction, 6-25, 7-1, 7-3, 7-7 Coprocessor Instruction Execution, 7-6 MOTOROLA Coprocessor Context Save and Context Restore Instruction Categories, 7-16 Coprocessor General Instruction Category, 7-8 cpBcc, 7-12 cpDBcc, 7-14 cpRESTORE, 7-17, 7-22 cpSAVE, 7-17, 7-20 cpScc, 7-13 cpTRAPcc, 7-15, 7-55 Exception-Related, 8-39 Illegal Instruction, 6-7 MOVE, 8-20 MOVE SR, 8-3 MOVEA, 8-20 MOVEC, 4-3 NOP, 5-62, 8-3 Prefetches, 4-1 Primitive Instructions, 7-27 RESET, 5-76, 7-58 RTE, 6-19, 6-24 RTM, 9-14, 9-16, 9-19 Shift/Rotate, 8-34 Single-Operand Instructions, 8-33 Special-Purpose MOVE, 8-29 STOP, 6-10 TAS, 5-39 Unimplemented Instruction, 6-7 Instruction Execution, 5-62, 8-1 Instruction Execution Overlap, 8-4 Instruction Pipe, 1-12, 4-1, 6-21 Instruction Prefetches, 8-1 Instruction Set, 1-10 Instruction Timing, 8-8, 8-9 Internal Cache Holding Register, 5-21 Interrupt, 6-1 Flowchart, 6-14 Interrupt Exception, 6-11 Nonmaskable, 6-12 Interrupt Acknowledge Cycle, 5-4, 5-45, 6-16 Timing, 5-46 Interrupt Exception, 5-45, 6-11 Interrupt Priority Mask, 5-45, 6-11 Interrupt Stack Pointer (ISP), 1-4, 2-2 IPEND Signal, 3-5, 6-14 IPL2-IPL0 Signals 3-5, 5-45, 6-11 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com INDEX-3 Freescale Semiconductor, Inc. -- L-- Long-Word Operand, 5-10, 5-14 Long-Word Read Cycle, 5-26 Long-Word Write Cycle, 5-33 Freescale Semiconductor, Inc... -- M-- M-Bit (SR), 1-7, 2-2 Main Processor Detected Address Error, 7-57 Bus Faults, 7-57 cpTRAPcc Instruction Traps, 7-55 Exceptions, 7-52 F-Line Emulator Exception, 7-54 Format Error, 7-57 Interrupts, 7-56 Privilege Violations, 7-55 Protocol Violation, 7-52 Trace Exception, 7-55 Master Stack Pointer (MSP), 1-4, 2-2 Maximum Ratings, 10-1 MC68881/MC68882 Floating-Point Coprocessors, 9-1 Memory Interface, 9-11 Misaligned Operand, 5-6, 5-14, 8-2 Transfer, 5-1, 5-5 Module, 9-14 Module Call, 9-18 Module Return, 9-19 Module Stack Frame, 9-16 MOVE Instruction, 8-20 MOVE SR Instruction, 8-3 MOVEA Instruction, 8-20 MOVEC Instruction, 4-3 -- N-- Nonmaskable Interrupt, 6-12 NOP Instruction, 5-62, 8-3 Normal Processing State, 2-1 -- O-- OCS Signal, 3-4, 5-3 Ordering Information MC68020, 11-1 MC68EC020, 11-1 Overlap, 8-3 INDEX-4 -- P-- Package Dimensions MC68020 FC Suffix, 11-6 MC68020 FE Suffix, 11-7 MC68020 RC Suffix, 11-3 MC68020 RP Suffix, 11-4 MC68EC020 FG Suffix, 11-11 MC68EC020 RP Suffix, 11-9 Pin Assignment MC68020 FC Suffix, 11-5 MC68020 FE Suffix, 11-5 MC68020 RC Suffix, 11-2 MC68020 RP Suffix, 11-2 MC68EC020 FG Suffix, 11-10 MC68EC020 RP Suffix, 11-8 Port Size, 5-1, 5-5, 5-21, 9-5 Power Supply, 3-7, 9-9 Primitive, 7-4, 7-27 Busy Response Primitive, 7-30 CA Bit, 7-29 DR Bit, 7-29 Evaluate and Transfer Effective Address Primitive, 7-35 Evaluate Effective Address and Transfer Data Primitive, 7-35 Format, 7-28 Null Coprocessor Response Primitive, 7-31 PC Bit, 7-29 Supervisor Check Primitive, 7-33 Take Address and Transfer Data Primitive, 7-39 Take Midinstruction Exception Primitive, 7-47 Take Postinstruction Exception Primitive, 7-48 Take Preinstruction Exception Primitive, 7-45 Transfer from Instruction Stream Primitive, 7-34 Transfer Main Processor Control Register Primitive, 7-41 Transfer Multiple Coprocessor Registers Primitive, 7-42 Transfer Multiple Main Processor Registers Primitive, 7-42 Transfer Operation Word Primitive, 7-33 Transfer Single Main Processor Register Primitive, 7-40 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Transfer Status Register and the scanPC Primitive, 7-44 Transfer to/from Top of Stack Primitive, 7-40 Write to Previously Evaluated Effective Address Primitive, 7-37 Privilege Level, 2-2 Changing, 2-3 Supervisor Level, 1-4, 2-2 User Level, 1-4, 2-2 Privilege Violation Exception, 6-7, 6-8 Processing States, 2-1 Program Counter (PC), 1-4 Programming Model, 1-4, 7-1, 7-2 -- R-- Read Cycle, 5-3, 5-4, 5-8, 5-14, 5-16, 5-18, 5-22, 5-26 Byte Read Cycle, 5-26 Long-Word Read Cycle, 5-26, 8-2 Timing, 5-26 Read-Modify-Write Cycle, 5-3, 5-39, 5-42 Timing, 5-39 Registers Address Registers, 1-4 CAAR, 1-7, 4-3, 4-4 CACR, 1-7, 4-2, 4-3 Data Registers, 1-4 DFC, 1-7 Internal Cache Holding Register, 5-21 Program Counter (PC), 1-4 SFC, 1-7 SR, 1-7, 4-1 VBR, 1-7 Reset, 4-3 Flowchart, 6-4 Reset Exception, 6-4 RESET Instruction, 7-58 RESET Signal, 3-6, 5-76, 6-4 Reset Exception, 6-4 RESET Instruction, 5-76 RESET Signal, 3-6, 5-76, 6-4 Retry, 5-56 RMC Signal, 3-4, 5-3, 5-39 RTE Instruction, 6-19, 6-24 RTM Instruction, 9-14, 9-16, 9-19 R/ W Signal, 3-4, 5-2, 5-3, 9-5 MOTOROLA -- S-- S-bit (SR), 1-7, 2-2, 2-3 Save and Restore Operations, 8-40 scanPC, 7-28 Sequencer, 8-2, 8-5 Shift/Rotate Instructions, 8-34 Signal(s), 3-8 A1,A0, 5-2, 5-7, 5-9, 5-21, 9-5 A15-A13, 7-6 A19-A16, 7-6 A31-A24, 4-1, 5-3 Address Bus, 3-2, 5-3 AS, 3-4, 5-2, 5-3 AVEC, 3-5, 5-4, 5-48, 5-53 BERR, 3-7, 5-4, 5-25, 5-53, 5-55, 6-4 BG, 3-6, 5-63, 5-66, 5-70, 5-71 BGACK, 3-6, 5-62, 5-63, 5-66 BR, 3-6, 5-63, 5-66, 5-70 Byte Select Control Signals, 9-5 CDIS, 3-7, 4-3 CLK, 3-7 D31-D0, 3-2, 5-3 DBEN, 3-5, 5-4 DS, 3-4, 5-4, 5-21 DSACK1, DSACK0, 3-5, 5-4, 5-5, 5-24, 5-46, 5-53, 9-5 ECS, 3-4, 5-3 FC2-FC0, 2-4, 3-2, 5-2, 5-3, 5-44, 7-6 Functional Groups, 3-1 HALT, 3-7, 5-4, 5-25, 5-53, 5-60 Input Signal, 5-2 Internal Signal, 5-2 IPEND, 3-5, 6-14 IPL2-IPL0, 3-5, 6-11 OCS, 3-4, 5-3 RESET, 3-6, 5-76, 6-4 RMC, 3-4, 5-3, 5-39 R/W, 3-4, 5-2, 5-3, 9-5 SIZ1, SIZ0, 3-2, 5-2, 5-3, 5-7, 5-9, 5-21, 9-5 Single-Operand Instruction, 8-33 SIZ1, SIZ0 Signals, 3-2, 5-2, 5-3, 5-7, 5-9, 5-21, 9-5 Source Function Code Register (SFC), 1-7 Special-Purpose MOVE Instruction, 8-29 Special Status Word (SSW), 6-21 Spurious Interrupt, 5-48 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com INDEX-5 Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Stack Frame Midinstruction, 7-47 Postinstruction, 7-48 Preinstruction, 7-46 Status Register (SR), 1-7, 4-1, 5-45, 6-1 STOP Instruction, 6-10 Supervisor Privilege Level, 1-4, 2-2 Supervisor Stack Pointer (SSP), 1-4, 2-2 Synchronous Cycles, 5-24 -- T-- T1, T0 Bits (SR), 1-7, 6-9 TAS Instruction, 5-39 Thermal Characteristics, 10-1 MC68020, 10-2 MC68020 CQFP Package, 10-2 MC68EC020, 10-4 MC68EC020 PQFP Package, 10-4 Thermal Resistance, 10-2, 10-4 Timing, 5-26, 5-33 Trace Exception, 6-9 Trace Modes, 1-7 Tracing, 6-9 INDEX-6 Transfer, 5-10, 5-14, 5-25 Bus Transfer, 5-1 Direction, 5-3 Misaligned, 5-1, 5-5 Operand Transfer, 5-1, 5-5 Trap Exception, 6-6 -- U-- Unimplemented Instruction (F-Line Opcode) Exception, 6-7 User Privilege Level, 1-4, 2-2 User Stack Pointer (USP), 1-4, 2-2 -- V-- V CC Connections, 3-7, 9-9 Vector Base Register (VBR), 1-7, 2-5, 6-2 Virtual Machine, 1-12 Virtual Memory, 1-10 -- W-- Write Cycle, 5-3, 5-9, 5-10, 5-12, 5-14, 5-16, 5-18, 5-22, 5-33, 5-38 Long-Word Write Cycle, 5-33 Timing, 5-33 M68020 USER'S MANUAL For More Information On This Product, Go to: www.freescale.com MOTOROLA