LM5025B LM5025B Active Clamp Voltage Mode PWM Controller Literature Number: SNVS354A LM5025B Active Clamp Voltage Mode PWM Controller General Description The LM5025B is a functional variant of the LM5025 active clamp PWM controller. The functional differences of the LM5025B are as follows: * The maximum PWM duty cycle is limited to less than 75% to reduce voltage stress on the power MOSFETs. * The CS2 hiccup mode threshold is increased to 0.5V * The CS2 filter discharge device is disabled * The VCC regulator continues to operate when the line UVLO is below the threshold of normal operation * The VREF regulator is switched off when the line UVLO input falls below the operating threshold * The internal 5k COMP pin pull-up resistor is removed The LM5025B PWM controller contains all of the features necessary to implement power converters utilizing the Active Clamp / Reset technique. With the active clamp technique, higher efficiencies and greater power densities can be realized compared to conventional catch winding or RDC clamp / reset techniques. Two control outputs are provided, the main power switch control (OUT_A) and the active clamp switch control (OUT_B). The two internal compound gate drivers parallel both MOS and Bipolar devices, providing superior gate drive characteristics. This controller is designed for high-speed operation including an oscillator frequency range up to 1MHz and total PWM and current sense propagation delays less than 100ns. The LM5025B includes a high-voltage start-up regulator that operates over a wide input range of 13V to 100V. Additional features include: Line Under Voltage Lockout (UVLO), softstart, oscillator UP/DOWN sync capability, precision reference and thermal shutdown. Features n Internal start-up bias regulator n 3A compound main gate driver n Programmable line under-voltage lockout (UVLO) with adjustable hysteresis n Voltage mode control with feed-forward n Adjustable dual mode over-current protection n Programmable overlap or deadtime between the main and active clamp outputs n Volt x Second maximum duty cycle clamp n Programmable soft-start n Current sense leading edge blanking n Single resistor programmable oscillator n Oscillator up / down sync capability n Precision 5V reference n Thermal shutdown Packages n TSSOP-16 n LLP-16 (5x5 mm) Thermally Enhanced Typical Application Circuit 20141101 Simplified Active Clamp Forward Power Converter (c) 2006 National Semiconductor Corporation DS201411 www.national.com LM5025B Active Clamp Voltage Mode PWM Controller March 2006 LM5025B Connection Diagram 20141116 16-Lead TSSOP, LLP Ordering Information Order Number Package Type NSC Package Drawing Supplied As LM5025BMTC TSSOP-16 MTC-16 92 Units per anti-static tube LM5025BMTCX TSSOP-16 MTC-16 2500 Units on Tape and Reel LM5025BSD LLP-16 SDA-16A 1000 Units on Tape and Reel LM5025BSDX LLP-16 SDA-16A 4500 Units on Tape and Reel Pin Descriptions Pin Name 1 VIN Source Input Voltage Input to start-up regulator. Input range 13V to 100V, with transient capability to 105V. 2 RAMP Modulator ramp signal An external RC circuit from Vin sets the ramp slope. This pin is discharged at the conclusion of every cycle by an internal FET, initiated by either the internal clock or the V*Sec Clamp comparator. 3 CS1 Current sense input for cycle-by-cycle limiting If CS1 exceeds 0.25V the outputs will go into Cycle-by-Cycle current limit. CS1 is held low for 50ns after OUT_A switches high providing leading edge blanking. 4 CS2 Current sense input for soft restart If CS2 exceeds 0.5V the outputs will be disabled and a softstart commenced. The soft-start capacitor will be fully discharged and then released with a pull-up current of 1A. After the first output pulse (when SS =1V), the SS charge current will revert back to 20A. 5 TIME Output overlap/Deadtime control An external resistor (RSET) sets either the overlap time or dead time for the active clamp output. An RSET resistor connected between TIME and GND produces in-phase OUT_A and OUT_B pulses with overlap. An RSET resistor connected between TIME and REF produces out-of-phase OUT_A and OUT_B pulses with deadtime. 6 REF Precision 5 volt reference output Maximum output current: 10mA Locally decouple with a 0.1F capacitor. Reference stays low until the VCC UV comparator and line UVLO comparator are satisfied. www.national.com Description Application Information 2 LM5025B Pin Descriptions (Continued) Pin Name 7 VCC Description Application Information 8 OUT_A Main output driver Output of the main switch PWM output gate driver. Output capability of 3A peak sink current. 9 OUT_B Active Clamp output driver Output of the Active Clamp switch gate driver. Capable of 1.25A peak sink current.. 10 PGND Power ground Connect directly to analog ground. 11 AGND Analog ground Connect directly to power ground. 12 SS Soft-start control An external capacitor and an internal 20A current source set the soft-start ramp. The SS current source is reduced to 1uA following a CS2 over-current event or an over temperature event. 13 COMP Input to the Pulse Width Modulator PWM duty cycle is controlled by the voltage applied to the COMP pin. The COMP pin voltage is reduced by a fixed 1V offset and compared with the RAMP pin signal. 14 RT Oscillator timing resistor pin An external resistor connected from RT to ground sets the internal oscillator frequency. 15 SYNC Oscillator UP/DOWN synchronization input The internal oscillator can be synchronized to an external clock with a frequency 20% lower than the internal oscillator's free running frequency. There is no constraint on the maximum sync frequency. 16 UVLO Line Under-Voltage shutdown An external voltage divider from the power source sets the shutdown comparator levels. The comparator threshold is 2.5V. Hysteresis is set by an internal current source (20A) that is switched on or off as the UVLO pin potential crosses the 2.5V threshold. - EP Output from the internal high voltage start-up If an auxiliary winding raises the voltage on this pin above the regulation setpoint, the internal start-up regulator. The VCC voltage is regulated to 7.6V. regulator will shutdown, reducing the IC power dissipation. Exposed PAD, underside of the LLP package Internally bonded to the die substrate. Connect to option GND potential with low thermal impedance. 3 www.national.com LM5025B Block Diagram Simplified Block Diagram 20141102 www.national.com 4 Human Body Model 2kV If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range -55C to 150C Junction Temperature 150C VIN to GND -0.3V to 105V VCC to GND -0.3V to 16V Operating Ratings (Note 1) CS1, CS2 to GND -0.3 to 1.00V All other inputs to GND -0.3 to 7V VIN Voltage ESD Rating (Note 2) 13 to 100V External Voltage Applied to VCC 8 to 15V Operating Junction Temperature -40C to +125C Electrical Characteristics Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 27.4k) unless otherwise stated (Note 3) Symbol Parameter Conditions Min Typ Max 7.9 Units Startup Regulator VCC Reg I-VIN VCC Regulation No Load 7.3 7.6 VCC Current Limit (Note 4) 20 25 Startup Regulator Leakage (external Vcc Supply) VIN = 100V 165 V mA 500 A VCC Supply VCC Under-voltage Lockout Voltage (positive going Vcc) VCC Reg 220mV VCC Reg 120mV VCC Under-voltage Hysteresis 1.0 1.5 VCC Supply Current (ICC) Cgate = 0 V 2.0 V 4.2 mA Reference Supply VREF Ref Voltage IREF = 0 mA Ref Voltage Regulation IREF = 0 to 10mA 4.85 Ref Current Limit 10 5 5.15 V 25 50 mV 20 mA Current Limit CS1 Prop CS1 Delay to Output CS1 Step from 0 to 0.4V Time to onset of OUT Transition (90%) Cgate = 0 40 ns CS2 Prop CS2 Delay to Output CS2 Step from 0 to 0.6V Time to onset of OUT Transition (90%) Cgate = 0 50 ns Cycle by Cycle Threshold Voltage (CS1) Cycle Skip Threshold Voltage (CS2) Resets SS capacitor; auto restart Leading Edge Blanking Time (CS1) 0.22 0.25 0.28 V 0.45 0.5 0.55 V 50 ns CS1 Sink Impedance (clocked) CS1 = 0.2V 30 50 CS1 Sink Impedance (Post Fault Discharge) CS1 = 0.3V 55 95 5 www.national.com LM5025B Absolute Maximum Ratings (Note 1) LM5025B Electrical Characteristics (Continued) Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 27.4k) unless otherwise stated (Note 3) Symbol Parameter Conditions CS2 Sink Impedance (Post Fault Discharge) CS2 = 0.6V CS1 and CS2 Leakage Current CS = CS Threshold 100mV Min Typ Max Units 55 95 1 A Soft-Start Soft-start Current Source Normal 17 22 27 A Soft-start Current Source following a CS2 event 0.5 1 1.5 A 180 175 200 220 225 kHz TJ = Tlow to Thigh 360 400 440 kHz TJ = 0C to 125C 364 Oscillator Frequency1 TA = 25C TJ = Tlow to Thigh Frequency2 RT = 13.3 k Sync threshold 436 2 Min Sync Pulse Width V 100 Sync Frequency Range 160 ns kHz PWM Comparator Delay to Output COMP step 5V to 0V Time to onset of OUT_A transition low 40 Maximum Duty Cycle 1 Measured at OUT_A 73 Maximum Duty Cycle 2 Measured at OUT_A; RT = 13.3K ns % 66 71 75 0.75 1 1.15 V 50 80 A 2.4 2.5 2.6 V Undervoltage Shutdown Threshold 2.44 2.5 2.56 V Undervoltage Shutdown Hysteresis 16 20 24 A 10 COMP to PWM Offset COMP Input Current COMP = 4V, SS open Volt x Second Clamp Ramp Clamp Level Delta RAMP measured from onset of OUT_A to Ramp peak. COMP = 5V UVLO Shutdown Output Section www.national.com OUT_A High Saturation MOS Device @ Iout = -10mA, 5 OUTPUT_A Peak Current Sink Bipolar Device @ Vcc/2 3 OUT_A Low Saturation MOS Device @ Iout = 10mA, 6 OUTPUT_A Rise Time Cgate = 2.2nF 20 ns OUTPUT_A Fall Time Cgate = 2.2nF 15 ns 6 A 9 (Continued) Specifications with standard typeface are for TJ = 25C, and those with boldface type apply over full Operating Junction Temperature range. VIN = 48V, VCC = 10V, RT = 26.7k, RSET = 27.4k) unless otherwise stated (Note 3) Symbol Typ Max Units OUT_B High Saturation Parameter MOS Device @ Iout = -10mA, Conditions Min 10 20 OUTPUT_B Peak Current Sink Bipolar Device @ Vcc/2 1 OUT_B Low Saturation MOS Device @ Iout = 10mA, 12 OUTPUT_B Rise Time Cgate = 1nF 20 ns OUTPUT_B Fall Time Cgate = 1nF 15 ns A 18 Output Timing Control Overlap Time RSET = 38 k connected to GND, 50% to 50% transitions 75 105 135 ns Deadtime RSET = 29.5 k connected to REF, 50% to 50% transitions 75 105 135 ns Thermal Shutdown TSD Thermal Shutdown Threshold 165 C Thermal Shutdown Hysteresis 25 C MTC Package 125 C/W SDA Package 32 C/W MTC Package 30 C/W SDA Package 5 C/W Thermal Resistance JA JC Junction to Ambient Junction to Case Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For guaranteed specifications and test conditions, see the Electrical Characteristics. Note 2: For detailed information on soldering plastic TSSOP and LLP packages, refer to the Packaging Data Book available from National Semiconductor Corporation. Note 3: All limits are guaranteed. All electrical characteristics having room temperature limits are tested during production with TA = TJ = 25C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 4: Device thermal limitations may limit usable range. 7 www.national.com LM5025B Electrical Characteristics LM5025B Typical Performance Characteristics VCC Regulator Start-up Characteristics, VCC vs Vin VCC vs ICC 20141103 20141104 VREF vs IREF Oscillator Frequency vs RT 20141106 20141105 Overlap Time vs Temperature RSET = 38K Overlap Time vs RSET 20141107 www.national.com 20141108 8 LM5025B Typical Performance Characteristics (Continued) Dead Time vs Temperature RSET = 29.5K Dead Time vs RSET 20141109 20141110 SS Pin Current vs Temperature 20141111 9 www.national.com LM5025B When the converter auxiliary winding is inactive, external current draw on the VCC line should be limited so the power dissipated in the start-up regulator does not exceed the maximum power dissipation of the controller. Detailed Operating Description The LM5025B is a functional variant of the LM5025 active clamp PWM controller. The functional differences of the LM5025B are as follows: * The maximum PWM duty cycle is limited to less than 75% to reduce voltage stress on the power MOSFETs * The CS2 hiccup mode threshold is increased to 0.5V An external start-up regulator or other bias rail can be used instead of the internal start-up regulator by connecting the VCC and the VIN pins together and feeding the external bias voltage into the two pins. * The CS2 filter discharge device is disabled * The VCC regulator continues to operate when the line UVLO is below the threshold of normal operation * The VREF regulator is switched off when the line UVLO input falls below the operating threshold * The internal 5k COMP pin pull-up resistor is removed The LM5025B PWM controller contains all of the features necessary to implement power converters utilizing the Active Clamp Reset technique. The device can be configured to control either a P-Channel clamp switch or an N-Channel clamp switch. With the active clamp technique higher efficiencies and greater power densities can be realized compared to conventional catch winding or RDC clamp / reset techniques. Two control outputs are provided, the main power switch control (OUT_A) and the active clamp switch control (OUT_B). The active clamp output can be configured for either a guaranteed overlap time (for P-Channel switch applications) or a guaranteed dead time (for N_Channel applications). The two internal compound gate drivers parallel both MOS and Bipolar devices, providing superior gate drive characteristics. This controller is designed for highspeed operation including an oscillator frequency range up to 1MHz and total PWM and current sense propagation delays less than 100ns. The LM5025B includes a highvoltage start-up regulator that operates over a wide input range of 13V to 100V. Additional features include: Line Under Voltage Lockout (UVLO), softstart, oscillator UP/DOWN sync capability, precision reference and thermal shutdown. Line Under-Voltage Detector The LM5025B contains a line Under Voltage Lock Out (UVLO) circuit. An external set-point voltage divider from Vin to GND, sets the operational range of the converter. The divider must be designed such that the voltage at the UVLO pin will be greater than 2.5V when Vin is in the desired operating range. If the undervoltage threshold is not met, both outputs and the VREF regulator are disabled. The VCC regulator is not disabled by UVLO. UVLO hysteresis is accomplished with an internal 20uA current source that is switched on or off into the impedance of the set-point divider. When the UVLO threshold is exceeded, the current source is activated to instantly raise the voltage at the UVLO pin. When the UVLO pin voltage falls below the 2.5V threshold, the current source is turned off causing the voltage at the UVLO pin to fall. The UVLO pin can also be used to implement a remote enable / disable function. Pulling the UVLO pin below the 2.5V threshold disables the PWM outputs. PWM Outputs The relative phase of the main (OUT_A) and active clamp outputs (OUT_B) can be configured for the specific application. For active clamp configurations utilizing a ground referenced P-Channel clamp switch, the two outputs should be in phase with the active clamp output overlapping the main output. For active clamp configurations utilizing a high side N-Channel switch, the active clamp output should be out of phase with main output and there should be a dead time between the two gate drive pulses. A distinguishing feature of the LM5025B is the ability to accurately configure either dead time (both off) or overlap time (both on) of the gate driver outputs. The overlap / deadtime magnitude is controlled by the resistor value connected to the TIME pin of the controller. The opposite end of the resistor can be connected to either REF for deadtime control or GND for overlap control. The internal configuration detector senses the connection and configures the phase relationship of the main and active clamp outputs. The magnitude of the overlap/dead time can be calculated as follows: Overlap Time (ns) = 2.8 x RSET - 1.2 Dead Time (ns) = 2.9 x RSET +20 RSET in k, Time in ns High Voltage Start-Up Regulator The LM5025B contains an internal high voltage start-up regulator that allows the input pin (VIN) to be connected directly to the line voltage. The regulator output is internally current limited to 20mA. When power is applied, the regulator is enabled and sources current into an external capacitor connected to the VCC pin. The recommended capacitance range for the VCC regulator is 0.1F to 100F. When the voltage on the VCC pin reaches the regulation point of 7.6V and the internal voltage reference (REF) reaches its regulation point of 5V, the controller outputs are enabled. The outputs will remain enabled until VCC falls below 6.2V or the line Under Voltage Lock Out detector indicates that VIN is out of range. In typical applications, an auxiliary transformer winding is connected through a diode to the VCC pin. This winding must raise the VCC voltage above 8V to shut off the internal start-up regulator. Powering VCC from an auxiliary winding improves efficiency while reducing the controller power dissipation. www.national.com 10 LM5025B PWM Outputs (Continued) 20141112 FIGURE 1. input. If the opto coupler is connected between the COMP pin and ground, then a pull-up resistor must be added between COMP and REF to bias the opto coupler transistor. The comparator polarity is such that 0V on the COMP pin will produce a zero duty cycle on both gate driver outputs. Compound Gate Drivers The LM5025B contains two unique compound gate drivers, which parallel both MOS and Bipolar devices to provide high drive current throughout the entire switching event. The Bipolar device provides most of the drive current capability and provides a relatively constant sink current which is ideal for driving large power MOSFETs. As the switching event nears conclusion and the Bipolar device saturates, the internal MOS device continues to provide a low impedance to compete the switching event. During turn-off at the Miller plateau region, typically around 2V - 3V, is where gate driver current capability is needed most. The resistive characteristics of all MOS gate drivers are adequate for turn-on since the supply to output voltage differential is fairly large at the Miller region. During turn-off however, the voltage differential is small and the current source characteristic of the Bipolar gate driver is beneficial to provide fast drive capability. Volt x Second Clamp The Volt x Second Clamp comparator compares the ramp signal (RAMP) to a fixed 2.5V reference. By proper selection of RFF and CFF, the maximum ON time of the main switch can be set to the desired duration. The ON time set by Volt x Second Clamp varies inversely with the line voltage because the RAMP capacitor is charged by a resistor connected to Vin while the threshold of the clamp is a fixed voltage (2.5V). An example will illustrate the use of the Volt x Second Clamp comparator to achieve a 50% duty cycle limit, at 200KHz, at a 48V line input: A 50% duty cycle at a 200KHz requires a 2.5s of ON time. At 48V input the Volt x Second product is 120V-s (48V x 2.5s). To achieve this clamp level choose RFF and CFF using the following equation:. RFF x CFF = VIN x TON / 2.5V = 48V x 2.5s / 2.5V = 48s Select CFF = 470pF RFF = 102k The recommended capacitor value range for CFF is 100pF to 1000pF. The CFF ramp capacitor is discharged at the conclusion of every cycle by an internal discharge switch controlled by either the internal clock or by the Volt x Second Clamp comparator, whichever event occurs first. Maximum Duty Cycle At low line input voltages, the Volt x Second clamp will not limit the maximum PWM duty cycle because the RAMP signal does not charge to the 2.5V threshold voltage within the period of the PWM clock. In this case, the maximum duty cycle is determined by the internal PWM clock and the output overlap or deadtime programmed by the resistor RSET connected to the TIME pin. Referring to Figure 1, the initial transition of OUT_B corresponds to the leading edge 20141113 PWM Comparator The PWM comparator compares the ramp signal (RAMP) to the loop error signal (COMP). This comparator is optimized for speed in order to achieve minimum controllable duty cycles. The COMP pin is a high impedance comparator 11 www.national.com LM5025B Maximum Duty Cycle but provides the advantage of continuous operation for short duration overload conditions. It is possible to utilize both over-current modes concurrently, whereby momentary overload conditions activate the CS1 cycle-by-cycle mode while prolonged overloading activates the CS2 hiccup mode. Generally the CS1 input will always be configured to monitor the main switch FET current each cycle. The CS2 input can be configured in several different ways depending upon the system requirements. (Continued) of the PWM clock. The leading edge of OUT_A is delayed with respect to OUT_B by the overlap time which is determined by the TIME pin resistor (K1 x RSET) When operating at maximum duty cycle, the trailing edge of OUT_A corresponds to the trailing edge of the PWM clock. The duty cycle at OUT_A is therefore always less than the duty cycle of the clock. The internal clock of the LM5025B operates at a nominal duty cycle of 75%. If the clock frequency is 400KHz and the overlap time is set to 100ns, then the maximum PWM duty cycle will be: a) The CS2 input can also be set to monitor the main switch FET current except scaled to a higher threshold than CS1 b) An external over-current timer can be configured which trips after a pre-determined over-current time, driving the CS2 input high, initiating a hiccup event. c) In a closed loop voltage regulaton system, the COMP input will rise to saturation when the cycle-by-cycle current limit is active. An external filter/delay timer and voltage divider can be configured between the COMP pin and the CS2 pin to scale and delay the COMP voltage. If the CS2 pin voltage reaches 0.5V a hiccup event will initiate. A small RC filter, located near the controller, is recommended for each of the CS pins. The CS1 input has an internal FET which discharges the current sense filter capacitor at the conclusion of every cycle, to improve dynamic performance. This same FET remains on an additional 50ns at the start of each main switch cycle to attenuate the leading edge spike in the current sense signal. The CS2 discharge FET only operates following a CS2 event, UVLO and thermal shutdown. The LM5025B CS comparators are very fast and may respond to short duration noise pulses. Layout considerations are critical for the current sense filter and sense resistor. The capacitor associated with the CS filter must be placed very close to the device and connected directly to the pins of the IC (CS and GND). If a current sense transformer is used, both leads of the transformer secondary should be routed to the filter network , which should be located close to the IC. If a sense resistor in the source of the main switch MOSFET is used for current sensing, a low inductance type of resistor is required. When designing with a current sense resistor, all of the noise sensitive low power ground connections should be connected together near the IC GND and a single connection should be made to the power ground (sense resistor ground point). Max Duty Cycle = 75% - 100ns x 400KHz = 71% Current Limit The LM5025B contains two modes of over-current protection. If the sense voltage at the CS1 input exceeds 0.25V the present power cycle is terminated (cycle-by-cycle current limit). If the sense voltage at the CS2 input exceeds 0.5V, the controller will terminate the present cycle, discharge the softstart capacitor and reduce the softstart current source to 1A. The softstart (SS) capacitor is released after being fully discharged and slowly charges with a 1A current source. When the voltage at the SS pin reaches approximately 1V, the PWM comparator will produce the first output pulse at OUT_A. After the first pulse occurs, the softstart current source will revert to the normal 20A level. Fully discharging and then slowly charging the SS capacitor protects a continuously over-loaded converter with a low duty cycle hiccup mode. These two modes of over-current protection allow the user great flexibility to configure the system behavior in over-load conditions. If it is desired for the system to act as a current source during an over-load, then the CS1 cycle-by-cycle current limiting should be used. In this case the current sense signal should be applied to the CS1 input and the CS2 input should be grounded. If during an overload condition it is desired for the system to briefly shutdown, followed by softstart retry, then the CS2 hiccup current limiting mode should be used. In this case the current sense signal should be applied to the CS2 input and the CS1 input should be grounded. This shutdown / soft-start retry will repeat indefinitely while the over-load condition remains. The hiccup mode will greatly reduce the thermal stresses to the system during heavy overloads. The cycle-by-cycle mode will have higher system thermal dissipations during heavy overloads, 20141114 www.national.com 12 The LM5025B oscillator is set by a single external resistor connected between the RT pin and GND. To set a desired oscillator frequency (F), the necessary RT resistor can be calculated from: RT = (4960/F)1.02 where F is in kHz and RT in k. The RT resistor should be located very close to the device and connected directly to the pins of the IC (RT and GND). A unique feature of LM5025B is the ability to synchronize the oscillator to an external clock with a frequency that is either higher or lower than the frequency of the internal oscillator. The lower frequency sync frequency range is 80% of the free running internal oscillator frequency. There is no constraint on the maximum sync frequency. A minimum pulse width of 100ns is required for the synchronization clock . If the synchronization feature is not required, the SYNC pin should be connected to GND to prevent any abnormal interference . The internal oscillator can be completely disabled by connecting the RT pin to REF. Once disabled, the sync signal will act directly as the master clock for the controller. Both the frequency and the maximum duty cycle of the PWM controller can be controlled by the sync signal (within the limitations of the Volt x Second Clamp). The maximum duty cycle (D) will be (1-D) of the sync signal. Thermal Protection Feed-Forward Ramp Internal Thermal Shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction temperature is exceeded. When activated, typically at 165C, the controller is forced into a low power standby state with the output drivers and the bias regulator disabled. The device will restart after the thermal hysteresis (typically 25C). During a restart after thermal shutdown, the soft-start capacitor will be fully discharged and then charged in the low current mode (1A) similar to a second level current limit event. The thermal protection feature is provided to prevent catastrophic failures from accidental device overheating. An external resistor (RFF) and capacitor (CFF) connected to VIN and GND are required to create the PWM ramp signal. The slope of the signal at the RAMP pin will vary in proportion to the input line voltage. This varying slope provides line feedforward information necessary to improve line transient response with voltage mode control. The RAMP signal is compared to the error signal at the COMP pin by the pulse width modulator comparator to control the duty cycle of the main switch output. The Volt x Second Clamp comparator also monitors the RAMP pin and if the ramp amplitude exceeds 2.5V, the present cycle is terminated. The ramp signal is reset to GND at the end of each cycle by either the internal clock or the Volt x Second comparator, which ever occurs first. Soft-start The soft-start feature allows the power converter to gradually reach the initial steady state operating point, thus reducing start-up stresses and surges. At power on, a 20A current is 13 www.national.com LM5025B sourced out of the soft-start pin (SS) into an external capacitor. The capacitor voltage will ramp up slowly and will limit the COMP pin voltage and therefore the PWM duty cycle. In the event of a fault as determined by VCC undervoltage, line undervoltage (UVLO) or second level current limit, the output gate drivers are disabled and the soft-start capacitor is fully discharged. When the fault condition is no longer present a soft-start sequence will be initiated. Following a second level current limit detection (CS2), the soft-start current source is reduced to 1A until the first output pulse is generated by the PWM comparator. The current source returns to the nominal 20A level after the first output pulse (~1V at the SS pin). The soft-start circuit controls the COMP pin voltage through a unity gain amplifier with an open drain (sink only) output. If the SS pin voltage is less than the PWM control signal applied to the COMP pin, this amplifier will sink current from the external pull-up connected to the COMP pin to force the COMP voltage to follow the soft-start capacitor ramp. When the soft-start capacitor charges to a voltage that is greater than the control voltage applied to the COMP pin, the softstart amplifier automatically disengages, allowing closed loop control of the PWM duty cycle. The soft-start amplifier output stage is capable of sinking up to 5mA. External pull-up circuits connected to the COMP pin must limit the current into the pin to a value less than 5mA. Oscillator and Sync Capability www.national.com 14 Application Circuit: Input 36-78V, Output 3.3V, 30A 20141117 LM5025B LM5025B Physical Dimensions inches (millimeters) unless otherwise noted Molded TSSOP-16 NS Package Number MTC16 Note: It is recommended that the exposed pad be connected to Pin 11 (AGND) 16-Lead LLP Surface Mount Package NS Package Number SDA16A 15 www.national.com LM5025B Active Clamp Voltage Mode PWM Controller Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated