TDE1707 (R) INTELLIGENT POWER SWITCH 0.5A OUTPUT CURRENT LOW SIDE OR HIGH SIDE SWITCH CONFIGURATION 6V TO 48V SUPPLY VOLTAGE RANGE OVERLOAD AND SHORT CIRCUIT PROTECTIONS INTERNAL VOLTAGE CLAMPING SUPPLY AND OUTPUT REVERSAL PROTECTION THERMAL SHUTDOWN GND AND VS OPEN WIRE PROTECTION ADJUSTABLE DELAY AT SWITCH ON INDICATOR STATUS LED DRIVER +5V REGULATED AUX. VOLTAGE DESCRIPTION The TDE1707 is a 0.5A Integrated Power Switch with up to 48V Power supply capability. Two output configurations are possible: - Load to Gnd. (High Side Mode) - Load to VS (Low side Mode) Especially dedicated to proximity detectors, its inBLOCK DIAGRAM September 2003 SO8 ORDERING NUMBER: TDE1707FP ternal +5V supply can be used to supply external circuits (See also AN495/0692). A signal is internally generated to block the In signal, and prevent activation of the output switch, as long as an abnormal condition is detected. The power-on transition, as well as the chip overtemperature and the output overcurrent, concurr to the generation of such signal. A minimum delay of 25s (Typ. value) is added to the trailing edge of such signal to ensure that a stable normal situation is present when the signal disappears. The delay (of the disapperance of the block signal; no delay at its on set) can be further increased connecting a capacitor between pin3 and ground. It can drive resistive or inductive loads. 1/6 TDE1707 PIN CONNECTION (Top view) ABSOLUTE MAXIMUM RATINGS Symbol Parameter VS Supply Voltage VSr IO Supply Reverse Voltage Output Current Vreg Vdelay Regulated Voltage Pin Delay Cap. Surce Pin VO Output Diff. Voltage Vi Input Voltage Value Unit 50 V 50 internally limited V A 0 to 7 0 to 5 V V 55 V -10 to 50 V Top Operating Temperature Range -25 to +85 C Tstg Storage Temperature -55 to 150 C Ptot El Power Dissipation Energy Induct. Load internally limited 150 W mJ THERMAL DATA Symbol Rth j-amb 2/6 Description Thermal Resistance Junction-ambient Max. Value Unit 150 C/W TDE1707 ELECTRICAL CHARACTERISTICS (VS = 24V; Tj = -25 to +85C, unless otherwise specified) Symbol Parameter Test Condition Min. Typ. Unit Vs 7 Supply Voltage 48 V Isr 7 Iq 7 Supply Reverse Current VSR = -48V 1.5 mA Quiescent Current Ireg = Iled = 0; Vi < 2V; VS = 6 to 48V 1.5 mA Io 8/2 Output Current Vs = 6V to 32V 500 mA Io 8/2 Output Current Vs = 32V to 48V 300 mA Vsat 8/2 Output Voltage Drop V8-2 Io = 500mA 1.6 V Vsat 8/2 Output Voltage Drop V8-2 Io = 300mA 1.5 V Isc 8/2 Short Circuit Current Vcl 8/2 Iolk 8/2 Internal Voltage Clamp ICL = 10mA Output Leakage 0 (Pin 2) Vi < 2V; Vo = 0 to Vs (Pin 8) Vith 5 Vihis 5 Ilk 5 6 Max. 1.1 Input Voltage Threshold 0.8 55 65 100 2 Input Threshold Hysteresis 2 Vi = 5V Vreg 6 Regulated Output Voltage Ireg < 5mA Iscr 6 Short Circuit Regulated Ireg 6 Ouput Regulator Current Vs = 35V Vs = 48V Iold 1 Current Surce Sink Led Driver Output ON () Vold 1 Voltage Drop Led Driver Ios = 2mA () Lead Driver (off) Leak. Vi < 2V; RL < 1K Idch 3 Del. Cap. Charge Current TJ = 25C Vdth 3 Delay Voltage Trigger TJ = 25C APPLICATION INFORMATION (See Application Circuit) The LED driver tells the output status. It can source or sink current (Iold typ = 3mA), according to the output configuration chosen. The thresholds, represented by the output comparator in the Block Diagram, are set at about 1.5V - 2V. For instance, in the High Side Load case of the A V 300 100 A A 3 V 300 Input Current Oldlk 1 0.5 mV A 2 5 4.5 5 5.5 V 6 30 50 mA 6 4 mA mA 3 4 mA 1.2 1.6 V 10 A 6 A 2 2 4 4 V Application Circuit, when the voltage on pin 8 (the output) differs from VCC less than 1.5V, the output is sensed in "OFF" state and the LED driver is disabled. If instead pin 8 differs from VCC more than 3V (the output comparator threshold value plus the drop voltage on the LED), then the output is sensed "ON" and the driver will force the current on the LED. DYNAMIC CHARACTERISTICS (VS = 24V; RL = 48; TJ = 25C) ton Propagation Turn on Time Vi = 0 to 5V 15 toff Propagation Turn off Time Vi = 5 to 0V 15 tdon Delayed Turn on Time / nF Delay Capacitor td min Minimum Delayed ton Delay Capacitor = 0 0.65 1 25 s s 2 ms s 3/6 TDE1707 APPLICATION CIRCUIT Figure 1: Input Thresholds Voltage vs. Temperature (VS = 24V) Figure 2: Saturation Voltage vs. Temperature (VS = 24V; IO = 500mA) Figure 3: Quiescent Current) vs.Temperature (VS = 24V) 4/6 TDE1707 mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.25 a2 MAX. 0.069 0.004 0.010 1.65 0.065 a3 0.65 0.85 0.026 0.033 b 0.35 0.48 0.014 0.019 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.020 c1 45 (typ.) D (1) 4.8 5.0 0.189 0.197 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F (1) 3.8 4.0 0.15 0.157 L 0.4 1.27 0.016 0.050 M S OUTLINE AND MECHANICAL DATA 0.6 0.024 SO8 8 (max.) (1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch). 5/6 TDE1707 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2003 STMicroelectronics - All rights reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com 6/6