OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 1 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Description:
The OPIA800 through OPID804 optoco uplers are designed for applications that utilize a digital output
(Phototlogic®) in a dual-in-line package. Isolation volta ge from 2,500 to 5,000 Vo lts RMS product are designed for
some of the most stringent power system isolation require ment s.
Theory of operation: The LED transmitt er is u sed to illuminate the Photosensor providing electrical isolation
between two power syste ms while maintaining the ability to transmit information from one power syste m to the
other. In many applications, analog or digital signals may be required to be transmitted between two power
systems while maintaining isolation between the power systems up to 5,000 volts RMS. A variety of LED and
photosensor configuratio ns are available depending on the system requirements
The ratio Current Transfer Ratio (CTR) is determined using the output current and input current for analog
photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device.
All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number.
Example: OPIA800DTU is a 8-Pin DIP shipped in a tube (TU).
Features:
• 2,500 or 5,000 Vrms electrical isolation
• Choice of a Single and Dual LED
• Choice of Phototransistor or Photologic® Sensor
• Low-cost plastic Dual-In-Line (DIP) package
Agency Approvals:
• UL Certification No: E58730
• VDE NO: 40026713, 40026624
RoHS
Applications:
• High voltage isolation
• PCBoard power system isolation
• Industrial equipment power isolation
• Medical equipment power isolation
• Office equipment
200100*
10
20 ==
−
−
=mA
mA
Curren
t
LED CurrentrPhotosenso
CTR
Moisture
1
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 2 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Analog Output Devices Ordering Information
Part Number Isolation Voltage
Max. (Vrms) CTR
Min/Typ/Max Typ. Tplh / Tphl (ns)
[RL = ohms] Package Configuration
OPIA800 2,500 300 / 1,600 / - 7 / 2 [ 2.2 K] 8 Pin DIP A K—K A B C E (Dar)
OPIA801 2,500 500 / 1,600 / - 10 / 5 [ 4.7 K] 8 Pin DIP A K—K A B C E (Dar)
OPIA802 2,500 15 / 43 / - 0.3 / 0.3 [ 1.9 K] 8 Pin DIP A K—K A C E
OPIA803 2,500 5 / 43 / - 0.4 / 0.3 [ 4.1 K] 8 Pin DIP A K—K A C E
Digital Output Devices Ordering Information
Part Number Isolation Voltage
Max. (Vrms) Typ. Tr / Tf (ns)
[RL = 350 ohms] Typ. Tplh / Tphl (ns)
[RL = ohms] Package Configuration
OPID804 5,000 30 / 30 45 / 45 [ 350] 8 Pin DIP A K—NAND
Configuration: Definition of Terms
LED Identification—Sensor Id entification
LED A = Anode K = Cathode
10K Logic 10K Inverted Logic NAND Gate NAND Gate
K = Cathode A = Anode B = Base C = Collector E = Emitter
Packaging Part Number Suffix: D = DIP, TU = Ship in Tubes, TR = Ship on Tape an d Reel
Example: OPID606DTR
Sensor
Part Number Pin #
1 2 3 4 5 6 7 8
OPIA800 A K E C C-B K-C
OPIA801 A K E C C-B K-C
OPIA802 A K E C A-B K
OPIA803 A K E C A-B K
OPID804 A K GND Output Enable Vcc
Package Outline Dimensions and Schematics: Top-View
Symbol Definition
A Anode
B Base
C Collector
E Emitter
K Cathode
OPID804
OPIA802
OPIA803
OPIA800
OPIA801
DIMENSIONS ARE IN: INCHES [MILLIMETERS]
TOLERANCE: ± 0.008 INCHES
[± 0.2 MILLIMETERS]
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 3 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Absolute Maximum Ratings (TA = 25o C unle s s otherwise noted)
Storage Temperature
-55° C to +125° C
Operating Temperature
OPIA800
OPIA801
OPIA802
OPIA803
OPID804
-40° C to +115° C
0° C to +125 ° C
-55° C to +115° C
-55° C to +100° C
0° C to +85° C
Isolation voltage (1 minute)
OPID804
OPIA800, OPIA801, OPIA802, OPIA803
5,000 Vrms
2,500 Vrms
Lead Soldering Temperature ( 1/16” (1.6 mm) from case for 5 seconds with soldering iron) 260° C
Input Diode
Continuous For ward Curr ent
OPIA802, OPIA803, OPID804
OPIA800 OPIA801
25 mA
20 mA
Peak Forward current (1 µs pulse width, 300 pps)
OPIA800, OPIA801, OPIA802, OPIA803
OPID804
1 A
40 mA
Reverse Voltage
OPIA800, OPIA801, OPIA802, OPIA803, OPID804
5 V
Power Dissipation
OPIA802, OPIA803, OPID804
OPIA800, OPIA801
45 mW
35 mW
Absolute Maximum Ratings (TA = 0° C to 70° C unless otherwise specified)
Output IC
Vcc—Collector-Emitter Voltage
OPIA800
OPIA801
OPIA802, OPIA803
-0.5 V to +7 V
-0.5 V to +18 V
-0.5 V to +15 V
Collector Current
OPIA802, OPIA803
OPIA800, OPIA801
8 mA
60 mA
Power Dissipation
OPIA800, OPIA801, OPIA802, OPIA803
100 mW
Output NAND Gate—OPID804
Vcc—Supply voltage 7 V
Enable voltage 5.5 V
High Level Output voltage 7 V
Low Level Output current 50 mA
Output Collector Power Dissipation 85 mW
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 4 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Electrical Characteristics: OPIA800
*6 Current transfer ratio is a ratio of input current and output current expressed in %.
*7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 5 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Switching Characteristics: OPIA800
*9 Instantaneous common mode rejectio n voltage “output(1)” represents a common voltage variation that can h old the output
above (1) level (Vo>2.0V).
*10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can h old the output
above (0) level (Vo>0.8V).
*8 Test Circuit Propagation Delay Time
*10 Test Circuit for Instantaneous Comm on Mode Rejection Voltage
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 6 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
OPIA800
Characteristic Curves
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 7 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
OPIA800
Characteristic Curves
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 8 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Electrical Characteristics: OPIA801
*6 Current transfer ratio is a ratio of input current and output current expressed in %.
*7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)
(TA = 25°C)
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 9 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Switching Characteristics: OPIA801
*9 Instantaneous common mode rejectio n voltage “output(1)” represents a common voltage variation that can h old the output
above (1) level (Vo>2.0V).
*10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can h old the output
above (0) level (Vo>0.8V).
*8 Test Circuit Propagation Delay Time
*10 Test Circuit for Instantaneous Comm on Mode Rejection Voltage
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 10 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Electrical Characteristics: OPIA802
*5 Current transfer ratio is a ratio of input current and output current expressed in %.
*6 Io = 2.4mA
*7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)
(TA = 0 to +70°C unless otherwise specifie d)
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 11 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Switching Characteristics: OPIA802
*8 RL = 1.9k ohms is equivalent to on LSTTL and 5.6k ohm pull-up resistor.
*9 Instantaneous common mode rejectio n voltage “output(1)” represents a common voltage variation that can h old the output
above (1) level (Vo>2.0V).
*10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can h old the output
above (0) level (Vo>0.8V).
*11 Bandwidth represents a point where AC input goes down by 3dB.
(TA = 25°C, VCC=5V, IF=16mA)
*9 Test Circuit Propagation Delay Time
*11 Test Circuit for Instantaneous Comm on Mode Rejection Voltage
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 12 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Electrical Characteristics: OPIA803 (TA = 0 to +70°C unless otherwise specifie d)
*5 Current transfer ratio is a ratio of input current and output current expressed in %.
*6 Io = 1.1mA
*7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 13 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Switching Characteristics: OPIA803
(TA = 25°C, VCC=5V, IF=16mA)
*8 RL = 4.1k ohms is equivalent to on LSTTL and 6.1k ohm pull-up resistor.
*9 Instantaneous common mode rejectio n voltage “output(1)” represents a common voltage variation that can h old the output
above (1) level (Vo>2.0V).
*10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can h old the output
above (0) level (Vo>0.8V).
*11 Bandwidth represents a point where AC input goes down by 3dB.
*9 Test Circuit Propagation Delay Time
*11 Test Circuit for Instantaneous Comm on Mode Rejection Voltage
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 14 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Electrical Characteristics: OPID804
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS
Input Diode
VF Forward Voltage (*4) - 1.6 1.8 V IF = 10 mA, TA = 25° C
BVR Reverse Breakdown Voltage 5 - - V IR = 10 µA, TA = 25° C
CIN Input Capacitance - 60 - pf VF = 0.0 V, f = 1M Hz
Output Photologic
VOL Low Level Output Voltage - 0.4 0.6 V IOL = 13 mA, VCC = 5.5 V, IF = 5 mA,
VEH=2V
IOH High Level Output Current - 2 250 µA
VCC=5.5 V, VO=5.5 V, VE=2.0 V, IF=250
µA
IEH High Level Enable Current - -0.8 - mA VCC = 5.5 V, VE = 2.0 V
IEL Low Level Enable Current -2.0 -1.2 - mA VCC = 5.5 V, VE = 2.0 V
ICCL Low Level Output Current - 13 18 mA VCC = 5.5 V, VE = 0.5 V, IF = 10 mA
ICCH High Level Output Current - 7 15 mA VCC = 5.5 V, VE = 0.5 V, IF = 0 mA
II-O Leakage Current - - 1.0 mA
VI-O = 3,000 V, TA = 25° C, t = 5 s,
RH = 45%
tEHL Enable Propagation delay “High to
Low” (*8) - 15 - ns VEH = 3.0 V, VEL = 0.5 V, RL = 350 Ω ,
IF = 7.5 mA, CLOAD = 15 pf
tELH Enable Propagation delay “Low to
High” (*8) - 40 -
IFHL / IFLH Hysteresis - 0.8 - Ratio VCC = 5 V, RL = 280 Ω
RI-O Input-Output Isolation resistance (*5) - 1012 - ohm VI-O = 500 V, TA = 25° C
CI-O Input-Output Capacitance (*5) - 0.6 - pf f = 1M Hz, TA = 25° C
tPHL & tPLH Propagation delay “High to Lo w”
and “Low to High” (*7) - 45 75
ns VCC = 5 V, RL = 350 Ω , IF = 7.5 mA,
CLOAD = 15 pf, TA = 25°C
tR & tF Rise and Fall Time - 30 -
CMH Instantaneous common mode rejectio n
voltage “High Output” (*9) - 500 - V/us
VCM = 10 V, RL = 350 Ω , IF = 0 mA,
VO = 2.0 V
CML Instantaneous common mode rejectio n
voltage “Low Output” (*9) - -500 - VCM = 10 V, RL = 350 Ω , IF = 5 mA,
VO = 0.8 V
(TA = 0 to +70°C unless otherwise specifie d)
Notes: (Typical values are all at VCC = 5V, Ta = 25°C.
*5 Measured as 2-Pin element. Connect pins 2 and 3, connect pins 5,6,7 and 8.
*6 DC current transfer ratio is defined as the ratio of output collector current to forward bias input current.
*7 Refer to Figure 1.
*8 Refer to Figure 2.
*9 CMH represents a common mode voltag e ignorable rise time ratio that can hold logic (1) state in output.
CML represents a common mode voltage ignorable fall time ratio that can hold logic (0) state in output.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 15 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Recommended Operating Conditions: OPIA804
Truth Table Circuit Block Diagram
Test Circuit Propagation Delay Time
Figure 1.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 16 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Test Circuit for Enable Propagation Delay Time
Figure 2.
Test Circuit for Instantaneous Common Mode Rejection Voltage
Figure 3.
Recommended Operating Conditions (cont.): OPIA804
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 17 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
OPID804
Characteristic Curves
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 18 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
OPID804
Characteristic Curves
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010
Page 19 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Quality / Reliability Requirements
Note: This is to be performed when a change occurs to form, fit or function.
Government and Industry Standard
Compliance Requirements
European Union’s Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC
Parameter Failure Criteria Conditions
HTRB D IC(OFF) ± 10% 11 samples after 500Hrs
0 Fail @ VCE = 5.0VDC, Ta = 70°C
HTFB D IC(ON) ± 10% 50 samples after 96Hrs
0 Fail @ Max PD, Ta = 25°C
MTTF @ 90% confidence 150,000 Min. @ 25°C, 25mADC
Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020B
Lead Solderability 0 Fail per Method 208 of MIL-STD-202.
Glass Transition of body 125°C Min. DSC test method
Temperature Humidity-Bias ± 20% 85°C, 85%RH, 500Hrs, 80% min Iceo
Temperature Cycle ± 20% per Method 1010.7 of MIL-STD-883E
High Temperature Storage ± 20% 85°C, 500Hrs
Autoclave 0 Fail
TA = 121°C, Pressure = 15psi, Humidit y
= 100%, Time = 96Hrs
Label Identification
DESCRIPTION:
Size: 3” (7.4 cm) X 2.2” (5.5 cm)
Lettering shall be black on white background.
Format shall be as:
Notes:
1. The DATE CODE is a 4-digit code for date of manufacture whe re YY is
the last two digits of the year, and WW is week n umber of manufacture.
2. The LOT I.D. is the manufacturing location lot identification where Y is
the year of manufacture, NNNN is a sequential lot identifier, and DDD
is the day of the year of manufacture. – or use equivalent label format.
Carrollton, TX, USA
MADE IN TAIWAN
OPTEK P/N __OPIA800D-TU__
IIIIIIIIIIIIIIIIIIIII
QTY. ________N/A_________
IIIIIIIIIIIIIIIIIIIII
DATE CODE _____(YYWW)___
IIIIIIIIIIIIIIIIIIIII
LOT I.D. ____(Y-NNNNDDD)__
IIIIIIIIIIIIIIIIIIIII
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 02/2010
Page 20 of 20
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA800—OPIA803, OPID804
DIP Package
Packaging Information:
Tube Packaging Specifications (TU):
Quantity: 8-pin: 48pcs/tube
DIMENSIONS ARE IN: INCHES [MILLIMETERS]
TOLERANCE: ± 0.008 INCHES
[± 0.2 MILLIMETERS]
Optek's Optocoupler
Part Numbers Packaging
Quantities
Tube Inner Small Carton Medium Carton Large Carton
Qty Weight
52 x 7 x 7.5
cm 53.5 x 16 x 17.5 cm 53.5 x 30.7 x 17.5 cm 53.5 x 30.7 x 25 cm
Qty Weight Qty Weight
Gross
Weight Qty Weight
Gross
Weight Qty Weight
Gross
Weig
ht
P/H
and
SMD
4-PIN
OPIA400D/A, OPIA410D/A -
OPIA413D/A 100 44 3,000 1.40 12,000 6.0 6.5 24,000 12.0 12.5 36,000 18.0 18.5
6-PIN
OPIA6XXD/A Series 65 44 1,950 1.50 7,800 6.5 7.0 15,600 12.0 12.5 23,400 18.5 19.0
8-PIN
OPIA8XXD Series and OPID804D 48 44 1,440 1.44 5,760 6.0 6.5 11,520 12.0 12.5 17,290 18.0 18.5
M/F
SOP
4-PIN and 5-PIN
OPIA401B - OPIA404B, OPIA414B,
OPIA500B 100 24 6,000 1.60 24,000 6.5 7.0 48,000 13.0 13.5 72,000 19.5 20.0
SSOP 4-PIN
OPIA405C - OPIA409C 170 -- 10,200 --
P/H = Pin-Hole Packages (Referred as D = Dual-In-L ine Package)
SMD = Standard Surface Mount Packages (Referred as A = 6.5mil SMD)
M/F or SOP = Mini-Flat Packages or Small Outside Packages (Referred as B = 4.40mil SM D w/ 2.54mil Lead-
Spacing)
SSOP = Shrink SOP Packages (Referred as C = 3.60mil SMD with 1.27mil Lead-Spacing)
