XR32220 2-Driver/2-Receiver Intelligent RS-232 Transceiver with 1.65V to 5.5V Interface Description The XR32220 product is a 2 driver/ 2 receiver RS-232 transceiver featuring a variable low voltage logic interface, down to 1.65V. This product is intended for portable or hand-held applications such as notebook and palmtop computers. The XR32220EBER device feature slew-rate limited outputs for reduced crosstalk and EMI. The XR32220EUER device is optimized for high speed with data rates up to 1Mbps, easily meeting the demands of high speed RS-232 applications. The XR32220 uses an internal high-efficiency charge-pump power supply that requires only four 0.1F capacitors in 3.3V operation. This charge pump combined with MaxLinear's driver architecture allow the XR32220 to deliver compliant RS-232 performance from a single power supply ranging from +3.0V to +5.5V. The AUTO ON-LINE(R) feature allows the device to automatically "wake-up" during a shutdown state when an RS-232 cable is connected and a connected peripheral is turned on. Otherwise, the device automatically shuts itself down drawing less than 1A. Typical Application VCC 9 24 T1IN T1OUT 5 T2IN T2OUT 6 0.1F RS-232 Outputs VCC To -P Supervisor Circuit 14 Shutdown 15 OnLine 13 Status Auto On-line / Control R1IN 3 12 R1OUT TTL/CMOS Outputs 5K 11 R2OUT RS-232 Inputs R2IN 4 5K GND VCC V- 24 23 22 21 20 19 NC 1 18 VL NC 2 17 GND R1IN 3 XR32220 16 C1- R2IN 4 24 pin QFN (4x4mm) 15 Online T1OUT 5 14 T2OUT 6 13 7 8 9 10 11 12 R1OUT 10 TTL/CMOS Inputs C2- V+ 23 0.1F R2OUT C2+ 20 C1+ 22 V+ Charge Pump T1IN C1+ C1- C2+ 0.1F 21 16 T2IN 0.1F VCC C2- 19 VL NC 18 APPLICATIONS Industrial and Single Board Computers Industrial and Process Control Equipment Point-Of-Sales Equipment Building Security and Automation 0.1F V- 0.1F NC VL FEATURES Meets true EIA/TIA-232-F Standards from a +3.0V to 5.5V power supply Interoperable with EIA/TIA-232 and adheres to EIA/TIA-562 down to a +2.7V power source 1.65V to 5.5V Logic Interface V pin L AUTO ON-LINE circuitry automatically wakes up from a 1A shutdown Regulated Charge Pump yields stable RS232 Outputs regardless of VCC variations Enhanced ESD Specifications 15kV Human Body Model 15kV IEC61000-4-2 Air Discharge 8kV IEC61000-4-2 Contact Discharge 250Kbps min transmission rate (speed grade B) 1000Kbps min transmission (speed grade U) -40C to 125C ambient operating temperature Lead-free (RoHS 6) package Shutdown Status 17 Figure 1. Typical Application Figure 2. Package Pinout REV1D 1/13 XR32220 Absolute Maximum Ratings Operating Conditions Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Maximum Rating condition for extended periods may affect device reliability and lifetime. Operating Temperature Range................... -40C to +125C VCC Supply Range............................................3.0V to 5.5V VL I/O Supply Range (VL VCC).....................1.65V to 5.5V Supply Voltage (VCC).................................... -0.3V to +6.0V Logic Interface Voltage (VL)...................................VL VCC V+.................................................................. -0.3V to +7.0V Thermal Information (24 Ld QFN (4x4mm)) JA.......................................................................39.2(C/W) V-................................................................... +0.3V to -7.0V JC.......................................................................15.3(C/W) V+ + |V-|....................................................................... 13V ICC (DC VCC or GND current)................................. 100mA Maximum Junction Temperature................................ 150C Input Voltages TxIN, ONLINE, Shutdown.............................. -0.3V to +6.0V RxIN.............................................................................. 15V Output Voltage TxOUT....................................................................... 13.2V RxOUT, Status.............................................. -0.3V to +6.0V Short-Circuit Duration TxOUT................................................................ Continuous Storage Temperature................................. -65C to +150C ESD Rating RS-232 Bus pins HBM - Human Body Model......................................... 15kV IEC614000-4-2 Air Discharge..................................... 15kV IEC614000-4-2 Contact Discharge............................... 8kV REV1D 2/13 XR32220 Electrical Characteristics Unless otherwise noted: TA = -40C to +125C, VCC = 3.3V 10% or 5.0V 10%, VL = VCC. Limits applying over the full operating temperature range are denoted by a *. Symbol Parameter Conditions * Min Typ Max Units DC CHARACTERISTICS ICC1 Supply Current, Auto On-Line enabled All RxIN open, Online = GND, Shutdown = VL, VCC = VL = 3.3V, TxIN = VL or GND * 1.0 10 A ICC2 Supply Current, Shutdown Shutdown = GND, VCC = VL = 3.3V, TxIN = VL or GND * 1.0 10 A ICC3 Supply Current, Auto On-Line disabled Online = Shutdown = VL, no load, VCC = VL = 3.3V, TxIN = VL or GND * 0.3 1.0 mA 1/3 * VL V LOGIC INPUTS AND OUTPUTS VIL Input Low Voltage VIH Input High Voltage IIL Input Leakage Current TxIN, Online, Shutdown; TAMB = 25C, VIN = 0V to VL IOL Output Leakage Current Status, RxOUT (Receivers disabled); VOUT = 0V to VL * VOL Output Low Voltage Status, RxOUT; IOUT = 1.5mA * VOH Output High Voltage Status, RxOUT; IOUT = -1.5mA * VL - 0.6 TxIN, Online, Shutdown; 1.65V VL 5.5V & VL VCC * * 2/3 * VL V 0.01 1.0 A 0.05 10 A 0.4 V V DRIVER OUTPUTS VSWING Output Voltage Swing All drivers outputs loaded with 3K to GND * 5.0 OR Output Resistance VCC = V+ = V- = 0V, VOUT = 2V * 300 IOSC Output Short-Circuit Current VOUT = 0V * IOL Output Leakage Current VCC = 0V or 3.0V to 5.5V, VOUT = 12V * 5.4 V 35 60 mA 25 A +15 V RECEIVER INPUTS IVR Input Voltage Range VIL Input Low Voltage VIH Input High Voltage RXHYS Receiver Input Hysteresis RXR Receiver Input Resistance * -15 VCC = 3.3V * 0.6 1.2 V VCC = 5.0V * 0.8 1.5 V VCC = 3.3V * 1.5 2.4 V VCC = 5.0V * 1.8 2.4 V 0.3 * REV1D 3 5 V 7 K 3/13 XR32220 Electrical Characteristics (Continued) Unless otherwise noted: TA = -40C to +125C, VCC = 3.3V 10% or 5.0V 10%, VL = VCC. Limits applying over the full operating temperature range are denoted by a *. Symbol Parameter Conditions * Min Typ Max Units AUTO ON-LINE CIRCUITRY CHARACTERISTICS (ONLINE = GND, SHUTDOWN = VL, VL = VCC) RXSTSH Receiver Threshold to STATUS high level * -2.7 +2.7 V RXSTSL Receiver Threshold to STATUS low level * -0.3 +0.3 V tSTSH Receiver Threshold to STATUS high Figure 11 0.2 s tSTSL Receiver Threshold to STATUS low Figure 11 30 s tONLINE Receiver Thresholds to Drivers Enabled Figure 11, (charge pump fully discharged when receiver threshold crossed) 30 s tOFFLINE Receiver Thresholds to Drivers Disabled Figure 11 35 s TIMING CHARACTERISTICS Maximum Output Frequency (Speed U) RL = 3K, CL = 250pF, 1 driver active * 1000 Kbps Maximum Output Frequency (Speed B) RL = 3K, CL = 1000pF, 1 driver active * 250 Kbps tPHL Receiver Propagation Delay (high to low) Receiver input (<10ns rise/fall) to Receiver output, CL = 150pF 0.15 s tPLH Receiver Propagation Delay (low to high) Receiver input (<10ns rise/fall) to Receiver output, CL = 150pF 0.15 s tRXSKEW Receiver Skew |tPHL - tPLH| 50 ns tRXOE Receiver Output Enable Time Normal operation 200 ns tRXOD Receiver Output Disable Time Normal operation 200 ns Driver Skew (Speed U) |tPHL - tPLH| (Driver propagation delays) * 50 100 ns Driver Skew (Speed B) |tPHL - tPLH| (Driver propagation delays) * 100 500 ns Transition-Region Slew Rate (Speed U) VCC = 3.3V, RL = 3K to 7K, CL = 150pF to 250pF, Measured from -3.0V to +3.0V or +3.0V to -3.0V Transition-Region Slew Rate (Speed B) VCC = 3.3V, RL = 3K to 7K, CL = 150pF to 1000pF, Measured from -3.0V to +3.0V or +3.0V to -3.0V fMAX tTXSKEW TXSLEW REV1D 90 * 6 V/s 30 V/s 4/13 XR32220 V- C2- C2+ C1+ V+ VCC Pin Configuration 24 23 22 21 20 19 17 GND R1IN 3 16 C1- R2IN 4 15 Online T1OUT 5 14 T2OUT 6 13 7 8 9 10 11 12 R1OUT 2 R2OUT NC T1IN VL T2IN 18 NC 1 NC NC Shutdown Status Pin Functions Pin Number Pin Name Type Description 1, 2, 7, 8 NC - 3, 4 R1IN, R2IN Inputs (5K pull-down) 5, 6 T1OUT, T2OUT Output 9, 10 T2IN, T1IN Input 11, 12 R2OUT, R1OUT Output TTL/CMOS Receiver Output. 13 Status Output TTL/CMOS level output indicating if no valid RS-232 levels are present at the R1IN or R2IN input pins. 14 Shutdown Input TTL/CMOS level input, when driven low puts the XR32220 into shutdown mode (tri-stating driver outputs and disabling the charge-pump); normal operation when driven high. 15 Online Input TTL/CMOS level input. A low input enables Auto On-Line mode, a high input disables Auto On-Line Mode. 16, 21 C1-, C1+ Analog Negative and positive terminals of voltage doubler charge pump capacitor. 17 GND Supply Ground. 18 VL Supply I/O Power Supply. 19 VCC Supply Power Supply. 20 V+ Analog Regulated positive (+5.5V) charge pump rail. 22, 23 C2+, C2- Analog Positive and negative terminals of the inverting charge pump capacitor. 24 V- Analog Regulated positive (-5.5V) charge pump rail. - Paddle Supply Ground. The exposed paddle on the bottom of package is connected to device ground. The paddle should be connected to ground on pcb. No Connect (not connect to the die). Can be left floating or tied to GND or VCC. 15KV ESD Protected, RS-232 Receiver Inputs. 15KV ESD Protected, RS-232 Driver Output. TTL/CMOS Driver Input. REV1D 5/13 XR32220 Typical Performance Characteristics 200 70 T1 Driver at full Data Rate T2 Driver at 15.5Kbps all Drivers loaded with 3K // CLoad 60 1Mbps 50 Supply Current (mA) Skew (ns) 150 100 T1 at 1Mbps T2 at 31.2Kbps All TX loaded with 3K // CLoad 50 40 250Kbps 120Kbps 30 20 20Kbps 10 0 0 500 1000 Load Capacitance (pF) 1500 0 2000 0 1000 2000 3000 4000 5000 Load Capacitance (pF) Figure 3. Transmitter Skew vs Load Capacitance Figure 6. Supply Current vs Load Capacitance 800kHz 95 50 4 90 85 1 Driver at 1Mbps Other Driver at 62.5Kbps All Drivers loaded with 3K // 250pF 80 0 75 -2 3.3V CCM 2.5V CCM 1.8V CCM 1.5V CCM 1.2V CCM 1.0V CCM 3.3V DCM 2.5V DCM 1.8V DCM 1.5V DCM 1.2V DCM 1.0V DCM 70 -4 65 60 0.1 2.5 3 3.5 4 Supply Voltage (V) IOUT (A) 1.0 4.5 35 500Kbps 30 25 250Kbps 20 15 10 5 5 0 Figure 4. Transmitter Output Voltage vs Supply Voltage 2.5 3 3.5 4 Supply Voltage (V) 4.5 5 Figure 7. Supply Current vs Supply Voltage 6 6 TxOUT+ 4 Transmitter Output Voltage (V) Transmitter Output Voltage (V) 1Mbps 40 2 -6 T1 at Full Data Rate T2 at 15.5Kbps All drivers loaded with 3K // 1000pF 45 Supply Current (mA) Efficiency (%)Voltage (V) Transmitter Output 6 100 2 XR32220EU, Supply = 3.3V, T1 at Full Data Rate (1Mbps) T2 Driver at 1/16th data rate All Drivers loads 3K // CLoad 0 -2 -4 -6 4 2 XR32220EB, Supply = 3.3V, T1 Driver at 250Kbps T2 Driver at 15.5Kbps All Drivers loads 3K // CLoad 0 -2 -4 TxOUT- 0 500 1000 1500 -6 2000 Load Capacitance (pF) Figure 5. Transmitter Output Voltage vs Load Capacitance 0 1000 2000 3000 Load Capacitance (pF) 4000 5000 Figure 8. Transmitter Output Voltage vs Load Capacitance REV1D 6/13 XR32220 Functional Block Diagram C1+ C1C2+ C2- V+ Charge Pump V- T1IN T1OUT TTL/CMOS Inputs RS-232 Outputs T2IN Shutdown OnLine Status T2OUT Auto On-line / Control R1OUT R1IN 5K TTL/CMOS Outputs R2OUT RS-232 Inputs R2IN 5K Figure 9. Functional Block Diagram REV1D 7/13 XR32220 Applications Information General Description The XR32220 transceiver meets the EIA/TIA-232 and ITU-T V.28/V.24 communication protocols and can be implemented in battery-powered, portable, or handheld applications such as notebook or laptop computers. The XR32220 device features MaxLinear's proprietary and patented (U.S. 5,306,954) on-board charge pump circuitry that generates 5.5V RS-232 voltage levels from a single +3.0V to +5.5V power supply. The XR32220EUER devices can operate at a data rate of 1000Kbps fully loaded. The XR32220 is a 2-driver/2-receiver device, ideal for portable or hand-held applications. The XR32220 is an ideal choice for power sensitive designs. The XR32220 devices feature AUTO ON-LINE(R) circuitry which reduces the power supply drain to a 1A supply current. In many portable or hand-held applications, an RS-232 cable can be disconnected or a connected peripheral can be turned off. Under these conditions, the internal charge pump and the drivers will be shut down. Otherwise, the system automatically comes online. This feature allows design engineers to address power saving concerns without major design changes. Theory of Operation The XR32220 series is made up of four basic circuit blocks: 1. Drivers 2. Receivers 3. The MaxLinear proprietary charge pump, and 4. AUTO ON-LINE(R) circuitry. Drivers The drivers are inverting level transmitters that convert TTL or CMOS logic levels to 5.0V EIA/TIA-232 levels with an inverted sense relative to the input logic levels. Typically, the RS-232 output voltage swing is 5.5V with no load and 5V minimum fully loaded. The driver outputs are protected against infinite short-circuits to ground without degradation in reliability. These drivers comply with the EIA-TIA-232-F and all previous RS-232 versions. Unused drivers inputs should be connected to GND or VL. Receivers The receivers convert +5.0V EIA/TIA-232 levels to TTL or CMOS logic output levels. Receivers are High-Z when the AUTO ON-LINE(R) circuitry is enabled and activated or when in shutdown. The truth table logic of the XR32220 driver and receiver outputs can be found in Table 2 on page 11. Since receiver input is usually from a transmission line where long cable lengths and system interference can degrade the signal, the inputs have a typical hysteresis margin of 300mV. This ensures that the receiver is virtually immune to noisy transmission lines. Should an input be left unconnected, an internal 5K pull-down resistor to ground will commit the output of the receiver to a HIGH state. Charge Pump The charge pump is a MaxLinear-patented design (U.S. 5,306,954) and uses a unique approach compared to older less-efficient designs. The charge pump still requires four external capacitors, but uses a four-phase voltage shifting technique to attain symmetrical 5.5V power supplies. The internal power supply consists of a regulated dual charge pump that provides output voltages of 5.5V regardless of the input voltage (VCC) over the +3.0V to +5.5V range. This is important to maintain compliant RS-232 levels regardless of power supply fluctuations. The charge pump operates in a discontinuous mode using an internal oscillator. If the output voltages are less than a magnitude of 5.5V, the charge pump is enabled. If the output voltages exceed a magnitude of 5.5V, the charge pump is disabled. This oscillator controls the four phases of the voltage shifting. A description of each phase follows. Phase 1 V- charge storage -- During this phase of the clock cycle, the positive side of capacitors C1 and C2 are initially charged to VCC. C1+ is then switched to GND and the charge in C1- is transferred to C2-. Since C2+ is connected to VCC, the voltage potential across capacitor C2 is now 2 times VCC. The drivers have a minimum data rate of 250kbps (XR32220EB) or 1000kbps (XR32220EU) fully loaded. VCC +VCC C4 V+ Storage Capacitor C1 C2 V- Storage Capacitor -VCC -VCC C3 Figure 10. Charge Pump - Phase 1 REV1D 8/13 XR32220 Applications Information (Continued) Phase 2 V- transfer -- Phase two of the clock connects the negative terminal of C2 to the VSS storage capacitor and the positive terminal of C2 to GND. This transfers a negative generated voltage to C3. This generated voltage is regulated to a minimum voltage of -5.5V. Simultaneous with the transfer of the voltage to C3, the positive side of capacitor C1 is switched to VCC and the negative side is connected to GND. VCC Phase 4 V+ transfer -- The fourth phase of the clock connects the negative terminal of C2 to GND, and transfers this positive generated voltage across C2 to C4, the V+ storage capacitor. This voltage is regulated to +5.5V. At this voltage, the internal oscillator is disabled. Simultaneous with the transfer of the voltage to C4, the positive side of capacitor C1 is switched to VCC and the negative side is connected to GND, allowing the charge pump cycle to begin again. The charge pump cycle will continue as long as the operational conditions for the internal oscillator are present. C4 VCC V+ Storage Capacitor C1 C2 V- Storage Capacitor -5.5V +5.5V C4 V+ Storage Capacitor C3 C1 C2 V- Storage Capacitor C3 Figure 11. Charge Pump - Phase 2 Phase 3 V+ charge storage -- The third phase of the clock is identical to the first phase -- the charge transferred in C1 produces -VCC in the negative terminal of C1, which is applied to the negative side of capacitor C2. Since C2+ is at VCC, the voltage potential across C2 is 2 times VCC. VCC +VCC C4 V+ Storage Capacitor C1 C2 V- Storage Capacitor -VCC -VCC C3 Figure 12. Charge Pump - Phase 3 Figure 13. Charge Pump - Phase 4 Since both V+ and V- are separately generated from VCC, in a no-load condition V+ and V- will be symmetrical. Older charge pump approaches that generate V- from V+ will show a decrease in the magnitude of V- compared to V+ due to the inherent inefficiencies in the design. The clock rate for the charge pump typically operates at greater than 250kHz. The external capacitors can be as low as 0.1F with a 16V breakdown voltage rating. The MaxLinear-patented charge pumps are designed to operate reliably with a range of low cost capacitors. Either polarized or non polarized capacitors may be used. If polarized capacitors are used they should be oriented as shown in the Typical Applications Circuit. The V+ capacitor may be connected to either ground or VCC (polarity reversed.) The charge pump operates with 0.1F capacitors for 3.3V operation. For other supply voltages, see the table for required capacitor values. Do not use values smaller than those listed. Increasing the capacitor values (e.g., by doubling in value) reduces ripple on the transmitter outputs and may slightly reduce power consumption. C2, C3, and C4 can be increased without changing C1's value. REV1D 9/13 XR32220 Applications Information (Continued) RS232 Receiver Input Voltage Table 1. Minimum Recommended Charge Pump Capacitor Values Supply Voltage VCC Charge Pump Capacitor Value for XR32220 3.0V to 3.6V C1 - C4 = 0.1F 4.5V to 5.5V C1 = 0.047F, C2 - C4 = 0.33F 3.0V to 5.5V C1 - C4 = 0.22F Invalid Region tSTSL tSTSH STATUS tOFFLINE RS232 Driver Output Voltage For best charge pump efficiency locate the charge pump and bypass capacitors as close as possible to the IC. Surface mount capacitors are best for this purpose. Using capacitors with lower equivalent series resistance (ESR) and self-inductance, along with minimizing parasitic PCB trace inductance will optimize charge pump operation. Designers are also advised to consider that capacitor values may shift over time and operating temperature. AUTO ON-LINE Circuitry The XR32220 devices have a patent pending AUTO ON-LINE(R) circuitry on board that saves power in applications such as laptop computers, palmtop (PDA) computers and other portable systems. (R) The XR32220 devices incorporate an AUTO ON-LINE(R) circuit that automatically enables itself when the external transmitters are enabled and the cable is connected. Conversely, the AUTO ON-LINE(R) circuit also disables most of the internal circuitry when the device is not being used and goes into a standby mode where the device typically draws 1A. This function is externally controlled by the ONLINE pin. When this pin is tied to a logic LOW, the AUTO ON-LINE(R) function is active. Once active, the device is enabled until there is no activity on the receiver inputs. The receiver input typically sees at least +3V, which are generated from the transmitters at the other end of the cable with a +5V minimum. When the external transmitters are disabled or the cable is disconnected, the receiver inputs will be pulled down by their internal 5k resistors to ground. When this occurs over a period of time, the internal transmitters will be disabled and the device goes into a shutdown or standby mode. When ONLINE is HIGH, the AUTO ON-LINE(R) mode is disabled. tONLINE +5V -5V V+ VCC Charge Pump 0V V- Figure 14. Auto On-Line(R) Timing The STATUS pin goes to a logic LOW when the cable is disconnected or the external transmitters are disabled. When the XR32220 drivers and internal charge pump are disabled, the supply current is reduced to 1A. This can commonly occur in hand-held or portable applications where the RS-232 cable is disconnected or the RS-232 drivers of the connected peripheral are turned off. The AUTO ON-LINE(R) mode can be disabled by the SHUTDOWN pin. If this pin is a logic LOW, the AUTO ON-LINE(R) function will not operate regardless of the logic state of the ONLINE pin. The truth table logic of the XR32220 driver and receiver outputs can be found in Table 3 on page 11. The STATUS pin outputs a logic LOW signal if the no valid RS-232 level is detected at either of the receiver inputs. This pin goes to a logic HIGH when the external transmitters are enabled and the cable is connected providing valid RS-232 voltage levels to the receiver input pins R1IN and R2IN. When the XR32220 is shut down, the charge pumps are turned off. V+ charge pump output decays to VCC, the V- output decays to GND. The decay time will depend on the size of capacitors used for the charge pump. Once in shutdown, the time required to exit the shut down state and have valid V+ and V- levels is typically 30s. For easy programming, the STATUS can be used to indicate DSR or a Ring Indicator signal. Tying ONLINE and SHUTDOWN together will bypass the AUTO ON-LINE(R) circuitry so this connection acts like a shutdown input pin. REV1D 10/13 XR32220 Applications Information (Continued) Table 2. XR32220 Operation Truth Table Valid RS-232 Level at Receiver Input Shutdown OnLine Driver Outputs Receiver Outputs Status Yes L x High-Z High-Z H Manually forced shutdown No L x High-Z High-Z L Manually forced shutdown Yes H L Active Active H Normal Operation (Auto On-Line(R) enabled) No H L High-Z Active L Standby Operation due to Auto On-Line(R) circuitry Yes H H Active Active H Normal Operation No H H Active Active L Normal Operation Mode of Operation Table 3. XR32220 Driver and Receiver Truth Table Shutdown RxIN RxOUT TxIN TxOUT L x High-Z x High-Z H L H L H H H L H L REV1D 11/13 XR32220 Package Description BOTTOM VIEW TOP VIEW SIDE VIEW Symbol A A1 A3 D E D2 E2 e b k L Dimensions in Millimeters Min. Nom Max 0.80 0.85 0.90 0 0.02 0.05 0.203 REF. 4.00 BSC 4.00 BSC 2.65 2.70 2.75 2.65 2.70 2.75 0.50 BSC 0.18 0.25 0.30 0.2 0.35 0.40 0.45 TERMINAL DETAILS TYPICAL RECOMMENDED LAND PATTERN 1. All dimensions are in Millimeters 2. Dimensions and tolerance per Jedec MO-220 Drawing No. : POD - 00000121 Revision: A.1 REV1D 12/13 XR32220 Ordering Information(1) Part Number Operating Temperature Range Lead-Free Package XR32220EBER-L Packaging Method Tray XR32220EBER-L/TR -40C to 125C XR32220EUER-L Yes(2) 24-pin QFN XR32220EUER-L/TR Tape and Reel Tray Tape and Reel (3) XR32220EBEVB XR32220EB Evaluation Board XR32220EUEVB XR32220EU Evaluation Board NOTE: 1. Refer to www.exar.com/XR32220 for most up-to-date Ordering Information. 2. Visit www.exar.com for additional information on Environmental Rating. 3. NRND - Not recommended for new designs. Revision History Revision Date Description 1A Sept 2014 Initial release of datasheet. 1B Sept 2016 Update max operating temperature range from 85C to 125C. Update Figure 4 and Ordering Information. Update to new datasheet format. 1C Aug 2017 Clarify junction temperature in Absolute Maximum Ratings to maximum of 150C. Update to MaxLinear logo. Update format. 1D Oct 2017 Add Evaluation Boards to Ordering Information. Corporate Headquarters: 5966 La Place Court Suite 100 Carlsbad, CA 92008 Tel.:+1 (760) 692-0711 Fax: +1 (760) 444-8598 www.maxlinear.com High Performance Analog: 48720 Kato Road Fremont, CA 94538 Tel.: +1 (510) 668-7000 Fax: +1 (510) 668-7001 Email: serialtechsupport@exar.com www.exar.com The content of this document is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by MaxLinear, Inc.. MaxLinear, Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content contained in this guide. Complying with all applicable copyright laws is the responsibility of the user. Without limiting the rights under copyright, no part of this document may be reproduced into, stored in, or introduced into a retrieval system, or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), or for any purpose, without the express written permission of MaxLinear, Inc. Maxlinear, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless MaxLinear, Inc. receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of MaxLinear, Inc. is adequately protected under the circumstances. MaxLinear, Inc. may have patents, patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document. Except as expressly provided in any written license agreement from MaxLinear, Inc., the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property. Company and product names may be registered trademarks or trademarks of the respective owners with which they are associated. (c) 2016 - 2017 MaxLinear, Inc. All rights reserved XR32220_DS_100517 REV1D 13/13