REFERENCE
PC817X*CSZ9F
1/10
Product name : PHOTOCOUPLER
Model No. : PC817
Business dealing name
1. These specification sheets include materials protected under copyright of Sharp Corporation ("Sharp").
Please do not reproduce or cause anyone to reproduce them without Sharp's consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product whic h does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions m entioned below .
(Precautions)
(1) Please do verify the validity of this part after assem bling it in customer’ s products, when customer
wants to make catalogue and instruction m anual based on the specification sheet of this part.
(2) This product is designed for use in the following application areas ;
· OA equipment Audio visual equipment · Home appliances
· Telecommunication equipment (Terminal) · Measuring equipment
· Tooling machines · Computers
If the use of the product in the above appl ication areas is for equipment listed in paragraphs
(3) or (4), please be sure to observe the precautions given in those respective paragraphs.
(3) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to e nsure reliability
and safety when this product is used for equi pment which demands high reliability and
safety in function and precision, such as ;
· T ransportation control and s afety equipment (aircraft, train, automobile etc.)
· Traffic signals · Gas leakage sensor breakers · Rescue and security equipment
· Other safety equipment
(4) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, s uch as ;
· Space equipment · Telecommunication equipment (for trunk lines)
· Nuclear power control equipment · Medical equipment
· Power generation and power transmission control s ystem（Key system）
(5) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above four paragraphs.
3. Please contact and consult with a Sharp sales re presentative for any questions about this product.
4. Warranty term and warranty limits
【Warranty term】
The warranty term for the shipped product shall be for 1 year after shipping to the designated place by the ordered
customer.
【Warranty limits】
SHARP supplies the replacement when this SHARP product shall be failed by SHARP's responsibility during above
warranty term. However , this warranty is excluded in case of the following.
(1)In case of improper handling and using by the customer.
(2) In case of that the cause of the failure is caused by the reason other than this SHARP product.
(3) In case of modification and repairing by person other than SHARP responsibilit y is not for SHARP.
(4) In case of a calamity, a disaster and such as the case when that responsibility is not for SHARP.
This warranty herein means the warranty for this SHARP product itself, SHARP takes no responsibility for any damage
caused by the failure of this SHARP product.
PC817XNCSZ9F
PC817X1CSZ9F
PC817X2CSZ9F
PC817X3CSZ9F
PC817X4CSZ9F
REFERENCE
PC817X*CSZ9F
2/10
1. Application
This specification a pplies to the outline an d characteristics of ph otocoupler Model No. PC817. (Lead free and Haloge n free type).
2. Outline Refer to the attached sheet, page 4.
3. Ratings and characteristics Refer to the atta ched sheet, page 5, 6.
4. Reliability Refer to the attached sheet, page 7.
5. Outgoing inspection Refer to the attached sheet, page 8.
6. Supplement
6.1 Isolation voltage shall be measured in the following method.
(1) Short between anode and ca thode on the prim ary side and between collector and em itter on the secondary side.
(2) The dielectric withstanding tester with zero-cross circuit shall be used.
(3) The wave form of app lied voltage shall be a sine wave.
(It is recomm ended that the isolation voltage be m easured in insulation oil.)
6.2 Package specifications Refer to the attached sheet, page 9, 10.
6.3 Collector current (Ic) Delivery rank table ("○" mark indicates bus iness dealing nam e of ordered product)
Rank at deliver y Business dealin g name Rank mark Ic (mA)
PC817XNCSZ9F with or without 2.5 to 30
PC817X1CSZ9F A 4.0 to 8.0
PC817X2CSZ9F B 6.5 to 13
PC817X3CSZ9F C 10 to 20
PC817X4CSZ9F D 15 to 30
6.4 This Model is a pproved by UL.
Approved Model No. : PC817
UL file No. : E64380
6.5 This Model is a pproved by CQC.
Approved Model No. : PC817
6.6 This product is not designed agains t irradiation.
This product is assembled with electrical input and o utput.
This product incorpor ates non-coherent light emittin g diode.
6.7 ODS materials
This product sh all not contain the foll owing materials.
Also, the following m aterials shall not be use d in the production pro cess for this product.
Materials for ODS : CFCS, Halon, Carbon tetrachloride, 1.1.1-Trichloroethane (Methyl chloroform)
6.8 Specified brom inated flame retardants
Specified brom inated flame retardants (PBB and PBDE) are n ot used in this device a t all.
T est conditions
IF=5mA
VCE=5V
Ta=25℃
REFERENCE
PC817X*CSZ9F
3/10
6.9 Complia nce with each regulation
(1) The RoHS directive (2002/95/EC)
This product complies with the RoHS directive (2002/95/EC) .
Object substan ces: mercury, lead, cadmium, hexav alent chromium, polybrom inated biphenyls (P BB)
and polybrominated diphenyl ethers (PBDE)
(2) Content of six substances specified in Management Methods for Control of Pollution Caused by Electronic Information
Products Regulation (Chinese : 电子信息产品污染控制管理办法).
Category
Toxic and hazardo us substances
Lead
(Pb) Mercury
(Hg) Cadmium
(Cd)
Hexavalent
chromium
(Cr6+)
Polybrominate d
biphenyls
(PBB)
Polybrominate d
diphenyl ethers
(PBDE)
Photocoupler ✓ ✓ ✓ ✓ ✓ ✓
✓: indicates that t he content of the toxic and hazardous subst ance in all the hom ogeneous materials of the p art is
below the conc entration limit requirem ent as described in SJ/T 1 1363-2006 standar d .
(3) This product complies with “Halogen free”.
“Halog en free” about this product is defined as follows.
The concentration ratio of Chlorinate and Bromine in raw material and indirect material , finished product can not
exceed 900 ppm, the total concentration of the 2 substance should not e xceed 1500 ppm.
7. Notes
Precautions for photocouplers ： Attachment-1
REFERENCE
PC817X*CSZ9F
4/10
W
6.5
2.54
±
0.25
Anode mark Factory identification m ark *3
Year cod
e
*1
±
0.
5
Pin-Number and internal connection diagram
Rank mark
ＳＨＡＲＰ
ＰＣ８１７
③Emitter
④Collector
Anode ①
Cathode ②
Epoxy resin
7.6
2
0.2
6
TYP.
±
0.30 4.
6
0.5
±
0.5
±
0.1
3.5
±
0.
5
±
0.
5
±
0.5
0.5 TYP.
2.8
3.3
7.6
2
～
9.98
Product mass : Approx. 0.23ｇ
Week cod
*
2
2. Outline
①
PC817 Outline Dimensions
(
Business dealin g name : PC817X*
C
SZ9F
)
UNIT : 1/1 m m
Name
② ③
④
Marking is las er marking
*1) Year date code
*2) 2-digit work week
*3) Factory identificati on marks applies t o the below
W：Lite-ON OPTO T echnolo gy (Changzhou) Co., Ltd. (CHINA)
Pin material : C u Alloy
Pin finish : Pure T in plating
REFERENCE
PC817X*CSZ9F
5/10
3. Ratings and characteristics
3.1 Absolute maximum ratings Ta=25℃
Parameter Symbol Rating Unit
Input
*1 Forward current IF 50 mA
Peak forward current IFM 1 A
Reverse voltage VR 6 V
Power dissipation P 70 mW
Output
Collector -emitter voltage VCEO 80 V
Emitter -collector voltage VECO 6 V
Collector current Ic 50 mA
*1 Collector power dissipation Pc 150 mW
Total power dissipation Ptot 200 mW
Operating temperatur e Topr -30 to +100 ℃
Storage temperature Tstg -55 to +125 ℃
*2 Isolation voltage Viso(rms) 5 kV
*3 Soldering temperature Tsol 270
℃
*1 The derating f actors of absolute maxim um ratings due to am bient temperature are shown in Fig. 1 to 2.
*2 AC For 1 min , 40 to 60%RH
Isolation volt age shall be measured usin g the following metho d.
(1) Short between an ode and cathode on the pri mary side and b etween collector and em itter on the
secondary side.
(2) The isolatio n voltage tester with zero-cross circuit shall be used.
(3) The waveform of applie d voltage shall be a sine wave.
*3 For 10s
3.2 Electro-optical characteristics Ta=25℃
Parameter Symbol Condition MIN. TYP. MAX. Unit
Input
Forward voltage VF I
F=20mA - 1.2 1.4 V
Peak forward voltage VFM I
FM=0.5A - - 3.0 V
Reverse current IR V
R=4V - - 10
μA
T erm inal capacitance Ct V=0, f=1kHz - 30 250 pF
Output
Dark current ICEO V
CE=50V, IF=0 - - 100 nA
Collector -emitter breakdown voltage BVCEO Ic=0.1mA IF=0 80 - - V
Emitter -collector brea kdown voltage BVECO IE=10μA, IF=0 6 - - V
T ransfer
charac-
teristics
Collector current Ic IF=5mA, VCE=5V 2.5 - 30 mA
*4 Current T ransfer Ratio CTR 50 - 600 %
Collector -emitter saturation vol tage VCE(sat) IF=20mA Ic=1mA - 0.1 0.2 V
Isolation resista nce R ISO DC500V 40 to 60%RH 5×1010 1011 - Ω
Floating capacitance Cf V=0, f=1MHz - 0.6 1.0 pF
Cut-of f frequency fc VCE=5V, Ic=2mA
RL=100Ω, -3dB - 80 - kHz
Rise time tr VCE=2V Ic=2mA
RL=100Ω - 4 18 μs
Fall time tf - 3 18 μs
*4 CTR (%) = (Ic /IF)×100
REFERENCE
PC817X*CSZ9F
6/10
200
150
100
50
00 25 50 75 100
-30
Ambient tem perature T a (℃)
Collector power dissipation
P
c (mW)
(Fig.
2
) Collector power dissipation
vs. ambient tem perature
125
250
-25
50
40
3
0
20
10
0
0
25 75 100
-30 50
(Fig. 1
)
Forward current
vs. ambient temperature
Forward current
I
F (mA)
Ambient tem perature T a (℃)
125
-25 55
REFERENCE
PC817X*CSZ9F
7/10
4. Reliability
The reliability o f products shall satisfy item s listed below.
Test item as require
T est title T est condition
Pre-condition test 125℃=24h, 85℃ 85%RH=168h, and IR reflow 260℃ peak=3 cycles
Temperature cycling test Ta=-55～125℃, Dwell time=15min per zone, 1000 cycles
Room tem perature operation life tes t Ta=25℃, IF=50mA, 1000h
High temperature operation life test Ta=110℃, IF=20mA, IC=30mA, 1000h
High temperature & high hum idity bias test Ta=85℃, 85%RH, VCE=64V, 1000h
High temperature bias test Ta=110℃, VCE=80V, 1000h
High temperature storage tes t Ta=150℃, 1000h
Low temperature storage t est Ta=-55℃, 1000h
Autoclave Temperature=121℃, 100%RH and 15Psi, 168h
Spec limit of pr oduct
Ta=25℃
Parameter Symbol Mesurement condition MIN. MAX. Unit
Forward voltage VF I
F=20mA - 1.4 V
Reverse current IR V
R=4V - 10
μA
Dark current ICEO V
CE=50V - 100 nA
Collector-emitter
breakdown voltage BVCEO I
C=0.1mA 80 - V
Emitter-collector
breakdown voltage BVECO I
E=10μA 6 V
Collector -emitter saturation vol tage VCE(sat) I
F=20mA,IC=1mA - 0.2 V
Current Transfer Ratio CTR IF=5mA,VCE=5V 50 600 %
Reliability cri teria
1. Reading va lue for each step test not over 50% D elta for VF, BVCEO, BVECO and IC parameter .
2. Reading va lue for each step test not over spec limit for IR, ICEO and VCE(sat) param eter .
3. Short and open is criteria of T em perature cycling test and Autoclave test item.
REFERENCE
PC817X*CSZ9F
8/10
5. Outgoing inspection
5.1 Inspection items
(1) Appearance
5.2 Sampling m ethod and Inspecti on level
A single sam pling plan, norm al inspection level II based o n ISO 2859 is applied.
The AQL accordi ng to the inspection items are shown be low .
Defect Inspection item AQL (%)
Major defect Unreadable marking 0.15
Minor defect Appearance defect exce pt the above mentione d. 0.65
REFERENCE
PC817X*CSZ9F
9/10
6.2 Packing specification
6.2.1 Package materials
Name Materials
Sleeve PS
Stopper TPR(Thermoplastic rubber)
Packing case ( Inner box) Paper
Packing case ( Outer carton)
6.2.2 Packing data
Sleeve volume
(pcs/sleeve) Inner box volume
(sleeve/box) Outer carton vol ume
(box/carton) Total volume
(pcs/outer carton)
100 20 12 24000
15mm
525mm
10mm
70mm
550mm
55mm
300mm
570mm
200mm
Sleeve
Inner box
Outer carton
REFERENCE
PC817X*CSZ9F
10/10
14.50
10.10
6.2.3 Sleeve and Stopper data
All dimensions are in millimeters.
REFERENCE
PC817X*CSZ9F
Attachment-1
Precautions for Photocouplers
1 Cleaning
(1) Solvent cleaning : Solvent temperature 45℃ or less
Immersion for 3 min or less
(2) Ultrasonic cleaning : The effect to device by ultrasonic cleaning dif fers by cleaning bath size, ultrasonic power output,
cleaning time, PCB size or device mounting condition etc. Please test it in actua l using condition
and confirm tha t any defect doesn't occur before starting the ultr asonic cleaning.
(3) Applicable solvent : Ethyl alcohol, Methyl alcoho l, Isopropyl alcohol
When the other solvent is used, there are cases that the packaging resin is eroded.
Please use the other solven t after thorough confirmation is perform ed in actual using condit ion.
2. Circuit design
2.1 The LED used in the Photocoupler generally decreases the light emission power by operation.
In case of long operation tim e, please design the circuit i n consideration of the degradation
of the light emission power of the LED. (50%/5 years)
2.2 There are cases that the deviat ion of the CTR and the degr adation of the relative light em ission power
of the LED increase when the setting value of IF is less than 1.0mA. Please design the c ircuit in consideration of this point.
3. Precautions for Soldering
(1) In the case of flow soldering (Avoid immersing units body in the solder）
One time soldering is recommended within the condition of temperature.
Temperature: 260+0/-5˚C
Time: 10 s.
Preheat temperature:25 to 140˚C
Preheat time: 30 to 80 s
(2) In the case of hand soldering by soldering iron
Allow single lead sol dering in every single process. One time solderin g is recommended.
Temperature: 380+0/-5˚C
Time: (max. ) 3s
(3) Other precautions
Depending on equi pment and s oldering conditions (temperatur e, Using solder etc.),
the effec t to the device and the PCB is dif ferent.
Please confirm that there is no problem on the actual use conditi ons in advance.
REFERENCE