PT6620 Series 6 A 12-V Input Integrated Switching Regulator SLTS036C - FEBRUARY 1999 - REVISED JUNE 2003 Standard Application REMOTE SENSE 1 VIN 4,5,6 PT6620 VOUT 11,12,13 3 C1 STBY 7,8,9,10 + C2 + LOAD Q1 COM COM C1 = Required 330F electrolytic (1) C2 = Required 330F electrolytic (1) Q1 = Optional N-Channel MOSFET Features Description * * * * * * * * The PT6620 series is a line of 12-V input Integrated Switching Regulators (ISRs). These regulators are designed for stand-alone operation in applications requiring as much as 6 A of output current. The PT6620 series is packaged in a 14-Pin SIP (Single In-line Package), which is available in either a vertical or horizontal configurations, including surface mount. Single Device: 6-A Output Input Voltage Range: 9 V to 16 V Adjustable Output Voltage 83 % Efficiency Remote Sense Capability Standby Function Over-Temperature Protection 16-pin Mount Option (Suffixes L, M, Q, & F) Pin Configuration Ordering Information PT Series Suffix (PT1234 x ) Pin Function PT6621 PT6622 PT6623 PT6624 PT6625 PT6626 PT6627 Case/Pin Configuration =3.3 Volts =1.5 Volts =2.5 Volts =3.6 Volts =5.0 Volts =9.0 Volts =1.8 Volts Order Suffix Package Code * 1 Vo Sense 2 Do Not Connect 3 STBY* 4 Vin 5 Vin 6 Vin 7 GND 8 GND 9 GND 10 GND Vertical Horiz SMD Horiz, 2-Pin Tab SMD, 2-Pin Tab Horiz, 2-Pin Ext Tab SMD, 2-Pin Ext Tab Vertical, Side Tab Horiz, Side Tab SMD, Side Tab 11 Vout * Previously known as package styles 400/410. 12 Vout 13 Vout (Reference the applicable package code drawing for the dimensions and PC board layout) 14 Vo Adjust P D E M L Q F R G B (EED) (EEA) (EEC) (EEM) (EEL) (EEQ) (EEF) (EEE) (EEG) (EEK) Specifications Unless otherwise stated, Ta =25 C, C2 =330 F, Vin =12 V, Io =Iomax PT6620 SERIES Characteristics Symbols Conditions Min Output Current Io Ta = 60 C, 200 LFM, pkg P Ta = 25 C, natural convection 0.1 0.1 Input Voltage Range Vin 0.1 A Io 6 A Output Voltage Tolerance Vo Ta = 0 to 60 C Output Voltage Adjust Range Voadj Pin 14 to Vo or ground Vo 5 V 6 V Vo 9 V Vo Vo Vo Vo Vo Vo = 3.3 V = 1.5 V = 2.5 V = 3.6 V =5 V =9 V Typ Max Units (2) (2) -- -- 6 6 A 9 Vo + 3 -- -- 16 16 V Vo - 0.1 -- 2.3 1.4 1.9 2.5 2.9 5.2 -- -- -- -- -- -- Vo + 0.1 4.5 2.6 3.7 4.8 6.5 10 V V Line Regulation Regline Vin(min) Vin Vin(max) -- 0.5 1 %Vo Load Regulation Regload 0.1 I o 6 A -- 0.5 1 %Vo Vo Ripple (pk-pk) Vr 20 MHz bandwidth, -- -- 50 1 -- -- mVpp %Vo t tr Vtr 1 A/s load step, 50 to 100% Io max Recovery time Vo over/undershoot -- -- 100 150 -- -- Sec mV Vo =3.3/3.6 V Vo = .5 V Vo =2.5 V Vo =5.0 V Vo =9.0 V -- -- -- -- -- 84 68 76 86 93 -- -- -- -- -- % Vo =3.3/3.6 V Vo =1.5 V Vo =2.5 V Vo =5.0 V Vo =9.0 V -- -- -- -- -- 83 66 75 85 92 -- -- -- -- -- % 500 550 550 650 600 750 kHz kHz Transient Response Efficiency Io =3 A Io =6 A Switching Frequency s Vin (min) VinVin(max) 0.1 A Io 6 A Vo < 6 V Vo > 6 V PT6622 Except PT6622 Continued For technical support and more information, see inside back cover or visit www.ti.com PT6620 Series 6 A 12-V Input Integrated Switching Regulator SLTS036C - FEBRUARY 1999 - REVISED JUNE 2003 Specifications (continued) PT6620 SERIES Characteristics Symbols Conditions Min Operating Temperature Range Ta Over V in range Typ Storage Temperature Ts -- -40 -- +125 C Mechanical Shock -- Per Mil-STD-883D, Method 2002.3 -- 500 -- G's Mechanical Vibration -- Per Mil-STD-883D, Method 2007.2, 20-2000 Hz, soldered in a PC board -- 7.5 -- G's Weight -- -- -- 14 -- grams -40 Max -- +85 Units (3) C Notes: (1) The PT6620 Series requires a 330 F(output) and 100 F(input) electrolytic capacitors for proper operation in all applications. (2) ISR will operate down to no load with reduced specifications (3) See safe Operating Area curves or contact the factory for the appropriate derating. T Y P I C A L PT6620 Series @Vin=12 V C H A R A C T E R I S T I C S Safe Operating Area, Vin =12 V (See Note A) PT6621/6622/6623P, Vo 3.3 V Efficiency vs Output Current 100 90.0 90 80.0 80 PT6621 PT6622 PT6623 70 PT6625 PT6626 60 50 Ambient Temperature (C) Efficiency (%) (See Note B) 70.0 Airflow 200LFM 120LFM 60LFM Nat conv 60.0 50.0 40.0 30.0 40 0 1 2 3 4 5 20.0 6 0.0 1.0 2.0 Output Current (A) Output Ripple vs Output Current 4.0 5.0 6.0 PT6625P, Vo =5 V 30 90.0 25 80.0 20 PT6621 PT6622 PT6623 15 PT6625 PT6626 10 5 Ambient Temperature (C) Ripple (mVpp) 3.0 Iout (A) 70.0 Airflow Nat conv 60LFM 120LFM 200LFM 60.0 50.0 40.0 30.0 0 20.0 0 1 2 3 4 5 6 0.0 1.0 2.0 Output Current (A) Power Dissipation vs Output Current 4.0 5.0 6.0 PT6626P, Vo =9 V 5 90.0 PT6621 3 PT6622 PT6623 PT6625 2 PT6626 1 Ambient Temperature (C) 80.0 4 Pd (Watts) 3.0 Iout (A) 70.0 Airflow Nat conv 60LFM 120LFM 200LFM 60.0 50.0 40.0 30.0 0 20.0 0 1 2 3 4 Output Current (A) 5 6 0.0 1.0 2.0 3.0 4.0 5.0 6.0 Iout (A) Note A: All characteristic data in the above graphs has been develped from actual products tested at 25 C. This data is considered typical for the ISR. Note B: SOA curves represent operating conditions at which internal components are at or below manufacturer's maximum rated operating temperatures. For technical support and more information, see inside back cover or visit www.ti.com Application Notes PT6620 Series Adjusting the Output Voltage of the PT6620 6 A, 12-V Bus Converter Series The output voltage of the Power Trends PT6620 Series ISRs may be adjusted higher or lower than the factory trimmed pre-set voltage with the addition of a single external resistor. Table 1 accordingly gives the allowable adjustment range for each model in the series as Va (min) and Va (max). Figure 1 1 Vsense 4,5,6 Vin PT6620 Vin GND STBY 11,12,13 Vo Vo(adj) 7,8,9,10 3 Adjust Up: An increase in the output voltage is obtained by adding a resistor R2, between Vo Adjust (pin 14) and GND (pins 7-10). Vo 14 (R1) Adj Down + + C in C out L O A D R2 Adjust Up Adjust Down: Add a resistor (R1), between Vo Adjust (pin 14 ) and Vout (pins 11-13). COM COM Refer to Figure 1 and Table 2 for both the placement and value of the required resistor, either (R1) or R2 as appropriate. Notes: 1. Use only a single 1% resistor in either the (R1) or R2 location. Place the resistor as close to the ISR as possible. The values of (R1) [adjust down], and R2 [adjust up], can also be calculated using the following formulae. 2. Never connect capacitors from Vo Adjust to either GND, Vout, or the Remote Sense pin. Any capacitance added to the Vo adjust pin will affect the stability of the ISR. 3. If the Remote Sense feature is being used, connecting the resistor (R1) between Vo Adjust (pin 14) and Remote Sense (pin 1) can benefit load regulation. 4. The minimum input voltage required by the part is Vout + 3, or 9 V, whichever is higher. (R1) = Ro (Va - 1.25) - Rs (Vo - Va) k R2 = 1.25 Ro Va - Vo k Where: Vo Va Ro Rs - Rs = Original output voltage = Adjusted output voltage = The resistance value in Table 1 = The series resistance from Table 1 Table 1 PT6620 ADJUSTMENT AND FORMULA PARAMETERS Series Pt # PT6622 PT6623 PT6621 PT6624 Vo (nom) Va (min) 1.5 V 2.5 V 3.3 V 3.6 V 5V 1.4 V 1.9 V 2.3 V 2.5 V 2.9 V Va (max) ) Ro (k 2.7 V 3.7 V 4.5 V 4.8 V 6.5 V ) Rs (k 2.49 4.99 10.0 4.99 PT6625 PT6626 9.0 V 5.2 V 10 V 12.1 12.1 16.2 12.1 12.1 12.1 12.1 12.1 For technical support and more information, see inside back cover or visit www.ti.com Application Notes continued PT6620 Series Table 2 PT6620 ADJUSTMENT RESISTOR VALUES Series Pt # Vo (nom) Va (req'd) 1.4 PT6622 1.5 V PT6623 2.5 V PT6621 3.3 V PT6624 3.6 V PT6625 5V (5.0) k 1.5 Series Pt # Vo (nom) Va (req'd) PT6625 5V PT6626 9V 5.2 89.1 k (0.5) k 5.3 55.4 k (1.1) k 1.6 59.9 k 5.4 38.5 k (1.9) k 1.7 28.7 k 5.5 28.4 k (2.6) k 1.8 18.3 k 5.6 21.7 k (3.4) k 1.9 13.1 k (5.8) k 5.7 16.8 k (4.2) k 2.0 10.0 k (10.0) k 5.8 13.2 k (5.1) k 2.1 7.9 k (16.3) k 5.9 10.4 k (6.1) k 2.2 6.4 k (26.7) k 6.0 8.2 k (7.1) k 2.3 5.3 k (47.5) k (0.6) k 6.1 6.3 k (8.1) k 2.4 4.4 k (110.0) k (3.4) k 6.2 4.8 k (9.3) k 2.5 3.8 k 6.3 3.5 k (10.5) k 2.6 3.2 k (6.8) k (1.7) k 120.0 k (11.2) k (4.2) k 6.4 2.4 k (11.9) k 2.7 57.5 k (17.1) k (7.4) k 6.5 1.4 k (13.3) k 2.8 36.7 k (25.4) k (11.3) k 6.6 (14.9) k 2.9 26.3 k (37.8) k (16.4) k (0.6) k 6.7 (16.6) k 3.0 20.0 k (58.5) k (23.2) k (2.1) k 6.8 (18.4) k 3.1 15.8 k (99.8) k (32.7) k (3.7) k 6.9 (20.5) k 3.2 12.9 k (224.0)k (46.9) k (5.5) k 7.0 (22.7) k 3.3 10.6 k (70.6) k (7.4) k 7.1 (25.2) k 3.4 8.9 k 139.0 k (118.0) k (9.7) k 7.2 (27.9) k 3.5 7.5 k 63.5 k (260.0) k (12.2) k 7.3 (31.0) k 3.6 6.4 k 38.3 k (15.1) k 7.4 (34.4) k 3.7 5.4 k 25.7 k 139.0 k (18.4) k 7.5 (38.3) k 3.8 18.2 k 63.5 k (22.3) k 7.6 (42.8) k 3.9 13.1 k 38.3 k (26.9) k 7.8 (53.9) k 4.0 9.5 k 25.7 k (32.5) k 8.0 (69.6) k 4.1 6.8 k 18.2 k (39.2) k 8.2 (93.0) k 4.2 4.7 k 13.1 k (47.6) k 8.4 (132.0) k 4.3 3.0 k 9.5 k (58.5) k 8.6 (210.0) k 4.4 1.7 k 6.8 k (73.0) k 8.8 (445.0) k 4.5 0.5 k 4.7 k (93.2) k 9.0 4.6 3.0 k (124.0) k 9.2 63.5 k 4.7 1.7 k (174.0) k 9.4 25.7 k 4.8 0.5 k (275.0) k 9.6 13.1 k (579.0) k 9.8 6.8 k 10.0 3.0 k 4.9 5.0 5.1 R1 = (Blue) 190.0 k R2 = Black For technical support and more information, see inside back cover or visit www.ti.com Application Notes PT6620 Series Using the Standby Function on the PT6620 Series of 12-V Bus Converters For applications requiring output voltage On/Off control, the 14-pin PT6620 ISR series incorporates a standby function. This feature may be used for power-up/shutdown sequencing, and wherever there is a requirement for the output status of the module to be controlled by external circuitry. Figure 1 1 Vsense 4,5,6 V in PT6620 Vin STBY The standby function is provided by the STBY* control, pin 3. If pin 3 is left open-circuit the regulator operates normally, providing a regulated output whenever a valid supply voltage is applied to Vin (pins 4, 5, & 6) with respect to GND (pins 7-10). Connecting pin 3 to ground 1 will disable the regulator output and reduce the input current to less than 30 mA 3. Grounding the standby control will also hold-off the regulator output during the period that input power is applied. The standby input is ideally controlled with an opencollector (or open-drain) discrete transistor (See Figure 1). It can also be driven directly from a dedicated TTL 2 compatible gate. Table 1 provides details of the threshold requirements. Table 1 Inhibit Control Thresholds (1,2) Parameter Min Max Enable (VIH) Disable (VIL) 1V -0.1V 5V 0.3V Notes: 1. The Standby input on the PT6620 regulator series may be controlled using either an open-collector (or open-drain) discrete transistor, or a device with a totem-pole output. A pull-up resistor is not necessary. The control input has an open-circuit voltage of about 1.5 Vdc. To disable the regulator output, the control pin must be "pulled" to less than 0.3 Vdc with a low-level 0.25 mA max. sink to ground. + 3 GND 7,8,9,10 Vo 11,12,13 Vo Vo(adj) + 14 C in C out COM COM Q1 BSS138 Inhibit +5V V in Turn-On Time: Turning Q1 in Figure 1 off, removes the low-voltage signal at pin 3 and enables the output. The PT6620 series of regulators will provide a fully regulated output voltage within 20ms. The actual turn-on time may vary with load and the total amount of output capacitance. Figure 2 shows the typical output voltage waveform of a PT6625 (5 V) following the prompt turn off of Q1 at time t =0 secs. The waveform was measured with a 12-V input voltage, and 5-A resistive load. Figure 2 Vo (2V/Div) 2. The Standby input on the PT6620 series is also compatible with TTL logic. A standard TTL logic gate will meet the 0.3 V VIL(max) requirement (Table 1 ) at 0.25 mA sink current. Do not drive the Standby control input above 5 Vdc. 3. When the regulator output is disabled the current drawn from the input source is reduced to approximately 15 mA (30 mA maximum). 4. The turn-off time of Q1, or rise time of the standby input is not critical on the PT6620 series. Turning Q1 off slowly, over periods up to 100 ms, will not damage the regulator. However, a slow turn-off time will increase both the initial delay and rate-of-rise of the output voltage. 0 2 For technical support and more information, see inside back cover or visit www.ti.com 4 6 8 10 t (milli - secs) 12 14 16 18 PACKAGE OPTION ADDENDUM www.ti.com 30-Aug-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins PT6621B NRND SIP MODULE EEK 14 PT6621D NRND SIP MODULE EEA 14 OBSOLETE SIP MODULE PT6621E Package Qty 12 Eco Plan (2) Lead/ Ball Finish MSL Peak Temp Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type EEC 14 TBD Call TI Call TI NRND SIP MODULE EEF 14 TBD Call TI Call TI PT6621G NRND SIP MODULE EEG 14 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6621L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6621M NRND SIP MODULE EEM 14 TBD Call TI Call TI 12 PT6621P NRND SIP MODULE EED 14 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6621Q NRND SIP MODULE EEQ 14 TBD Call TI Call TI PT6622B NRND SIP MODULE EEK 14 TBD Call TI Call TI PT6622E NRND SIP MODULE EEC 14 TBD Call TI Call TI PT6622F NRND SIP MODULE EEF 14 TBD Call TI Call TI PT6622G NRND SIP MODULE EEG 14 TBD Call TI Call TI PT6622L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6622M NRND SIP MODULE EEM 14 TBD Call TI Call TI 12 PT6622P NRND SIP MODULE EED 14 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6622Q NRND SIP MODULE EEQ 14 TBD Call TI Call TI PT6622R NRND SIP MODULE EEE 14 TBD Call TI Call TI PT6623B NRND SIP MODULE EEK 14 TBD Call TI Call TI PT6623D NRND SIP MODULE EEA 14 TBD Call TI Call TI PT6623E NRND SIP MODULE EEC 14 TBD Call TI Call TI PT6623G NRND SIP MODULE EEG 14 TBD Call TI Call TI PT6623L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6623M NRND SIP MODULE EEM 14 TBD Call TI Call TI PT6623Q NRND SIP MODULE EEQ 14 TBD Call TI Call TI PT6623R NRND SIP MODULE EEE 14 TBD Call TI Call TI PT6624B NRND SIP MODULE EEK 14 TBD Call TI Call TI PT6624E NRND SIP MODULE EEC 14 TBD Call TI Call TI PT6624F NRND SIP MODULE EEF 14 TBD Call TI Call TI PT6624G NRND SIP MODULE EEG 14 TBD Call TI Call TI Addendum-Page 1 Samples (Requires Login) TBD PT6621F 12 (3) PACKAGE OPTION ADDENDUM www.ti.com 30-Aug-2012 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6624M NRND SIP MODULE EEM 14 TBD Call TI Call TI PT6624P NRND SIP MODULE EED 14 TBD Call TI Call TI PT6624Q NRND SIP MODULE EEQ 14 TBD Call TI Call TI PT6624R NRND SIP MODULE EEE 14 TBD Call TI Call TI PT6625D NRND SIP MODULE EEA 14 12 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6625E NRND SIP MODULE EEC 14 12 Pb-Free (RoHS) Call TI Level-1-215C-UNLIM PT6625F NRND SIP MODULE EEF 14 TBD Call TI Call TI PT6625G NRND SIP MODULE EEG 14 Pb-Free (RoHS) Call TI N / A for Pkg Type PT6625L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6625M NRND SIP MODULE EEM 14 TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type PT6625P NRND SIP MODULE EED 14 PT6625Q NRND SIP MODULE EEQ 14 PT6625R NRND SIP MODULE EEE 14 PT6626B NRND SIP MODULE EEK 14 TBD Call TI Call TI PT6626E NRND SIP MODULE EEC 14 TBD Call TI Call TI PT6626F NRND SIP MODULE EEF 14 TBD Call TI Call TI OBSOLETE SIP MODULE PT6626G 12 12 EEG 14 TBD Call TI Call TI PT6626L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6626M NRND SIP MODULE EEM 14 PT6626P NRND SIP MODULE EED 14 PT6626Q NRND SIP MODULE EEQ 14 PT6626R NRND SIP MODULE EEE 14 PT6627D NRND SIP MODULE EEA 14 PT6627E NRND SIP MODULE EEC TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type TBD Call TI Call TI Pb-Free (RoHS) Call TI N / A for Pkg Type TBD Call TI Call TI 14 TBD Call TI Call TI 12 12 PT6627F NRND SIP MODULE EEF 14 TBD Call TI Call TI PT6627G NRND SIP MODULE EEG 14 TBD Call TI Call TI PT6627L NRND SIP MODULE EEL 14 TBD Call TI Call TI PT6627M NRND SIP MODULE EEM 14 TBD Call TI Call TI PT6627P NRND SIP MODULE EED 14 TBD Call TI Call TI PT6627Q NRND SIP MODULE EEQ 14 TBD Call TI Call TI Addendum-Page 2 Samples (Requires Login) PT6624L 12 (3) PACKAGE OPTION ADDENDUM www.ti.com 30-Aug-2012 Orderable Device PT6627R Status (1) NRND Package Type Package Drawing SIP MODULE EEE Pins Package Qty Eco Plan 14 TBD (2) Lead/ Ball Finish Call TI MSL Peak Temp (3) Samples (Requires Login) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 MECHANICAL DATA MPSI013 - MARCH 2001 EEA (R-PSIP-T14) PLASTIC SINGLE-IN-LINE MODULE 1.71 (43,43) MAX. 0.38 (9,65) 0.59 (14,98) 0.018 (0,45) 0.012 (0,30) 1.22 (30,98) MAX. Note G 0.52 (13,20) 0.017 (0,43) TYP. 1 0.100 (2,54) TYP. 0.040 (1,01) 0.017 (0,43) TYP. 0.42 (10,66) MAX. 0.205 (5,20) 0.140 (3,55) MIN. 1.77 (44,95) 0.175 (4,44) 1.42 (36,06) Note E 1.31 (33,27) Note F 0.20 (5,08) 1 o0.035 (0,88) MIN. 14 Places Plated through 0.100 (2,54) 13 Places 0.235 (5,96) 0.07 (1,77) 0.040 (1,01) PC Layout NOTES: A. B. C. D. E. F. 4202005/A 02/01 All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. No copper, power or signal traces in this area. POST OFFICE BOX 655303 G. D-suffix parts include a metal heat spreader. No signal traces are allowed under the heat spreader area. A solid copper island is recommended, which may be grounded. A-suffix does not include a metal heat spreader. * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI014A - MARCH 2001 - REVISED FEBRUARY 2002 EEK (R-PSIP-G14) PLASTIC SINGLE-IN-LINE MODULE Suffix B 2.36 (62,48) MAX. 2.000 (50,80) 1.71 (43,43) MAX. 0.325 (8,25) 0.38 (9,65) o0.187 (4,74) 2 Places 0.59 (14,98) 0.41(10,41) Note F 1.22 (30,98) 0.83 MAX. (21,08) 0.52 (13,20) 1 0.19 (4,82) 0.205 (5,20) 0.350 (8,89) 0.61 (15,49) 0.080 (2,02) MIN 0.100 (2,54) TYP. 0.017 (0,43) TYP. 0.42 (10,66) MAX. Seating Plane 0.006 (0,15) MAX. 2.42 (61,46) 2.000 (50,80) 0.175 (4,44) 0.10 (2,54) 0.325 (8,25) Note E, F Hole for #6-32 screws 1.77 (44,95) 1.42 (30,06) 0.040 (1,01) 0.86 (21,84) 1.35 (34,29) Note H 0-7 Gage Plane 0.17 (4,32) 0.150 (3,81) Note G 0.040 (1,01) 14 Places 0.100 (2,54) 13 Places 0.235 (5,97) 0.350 (8,89) 0.64 (16,25) PC LAYOUT NOTES: A. B. C. D. E. F. 0.017 (0,43) TYP. 4202006/B 02/02 All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. The metal tab is isolated but electrically conductive. No signal traces are allowed under the metal tab area. A solid copper island is recommended, which may be grounded. POST OFFICE BOX 655303 G. Power pin connections should utilize two or more vias per input, ground and output pin. H. No copper, power or signal traces in this area. * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI015A - MARCH 2001 - REVISED JANUARY 2002 EEC (R-PSIP-G14) PLASTIC SINGLE-IN-LINE MODULE Suffix E, C (Note F) 1.71 (43,43) MAX. 0.38 (9,65) 0.59 (14,98) 0.018 (0,45) 0.012 (0,30) 1.22 (30,98) MAX. Note F 0.52 (13,20) 1 0.100 (2,54) TYP. 0.080 (2,02) MIN. 0.42 (10,66) MAX. 0.017 (0,43) TYP. 0.205 (5,20) Seating Plane 0.006 (0,15) MAX. 1.77 (44,95) 0.175 (4,44) Note E, F 1.42 (36,06) 0.040 (1,01) 1.35 (34,29) Note H 0-7 Gage Plane 1 See Note G 0.150 (3,81) 0.040 (1,01) 14 Places 0.100 (2,54) 13 Places 0.235 (5,96) PC LAYOUT NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. E-suffix parts include a metal heat spreader. No signal traces are allowed under the heat spreader area. A solid copper island is recommended, which may be grounded. C-suffix does not include a metal heat spreader. POST OFFICE BOX 655303 0.017(0,43) TYP 0.10 (2,54) 0.17 (4,31) 4202007/B 12/01 G. Power pin connections should utilize two or more vias per input, ground and output pin. H. No copper, power or signal traces in this area. * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI016A - MARCH 2001 - REVISED FEBRUARY 2002 EEG (R-PSIP-T14) PLASTIC SINGLE-IN-LINE MODULE Suffix G 2.36 (62,48) MAX. 2.000 (50,80) 1.71 (43,43) MAX. o0.187 (4,74) 2 Places 0.38 (9,65) 0.59 (14,98) 0.325 (8,25) 0.41 (10,41) Note F 1.22 (30,98) 0.83 MAX. (21,08) 0.52 (13,20) 0.017 (0,43) TYP. 1 0.205 (5,20) 0.100 (2,54) TYP. 0.350 (8,89) 0.19 (4,82) 0.61 (15,49) 0.040 (1,01) 0.42 (10,66) MAX. 0.017 (0,43) TYP. 0.140 (3,55) MIN. 2.42 (61,46) 2.000 (50,80) 1.77 (44,95) 0.175 (4,44) 0.20 (5,08) 0.07 (1,77) 1.42 (30,06) 0.325(8,25) Note E, F Hole for #6-32 screws 1.31 0.86 (21,84) (33,27) Note G o0.035 (0,88) MIN. 14 Places Plated through 0.65 0.100 (2,54) 13 Places 0.235 (5,97) 0.350 (8,89) 0.040 (1,01) (16,51) PC LAYOUT 4202008/B 02/02 NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. The metal tab is isolated but electrically conductive. No signal traces are allowed under the metal tab area. A solid copper island is recommended, which may be grounded. G. No copper, power or signal traces in this area. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI017 - MARCH 2001 EED (R-PSIP-T14) PLASTIC SINGLE-IN-LINE MODULE 1.71 (43,43) MAX. 0.38 (9,65) 0.59 (14,98) 0.018 (0,45) 0.012 (0,30) 1.22 (30,98) MAX. Note F 0.52 (13,20) 1 0.100 (2,54) TYP. 0.170 (4,31) MIN. 0.017 (0,43) TYP. 0.205 (5,20) 1.77 (44,95) 0.235 (5,96) 0.017 (0,43) TYP. 0.42 (10,66) MAX. 0.040 (1,01) 0.100 (2,54) 13 Places 1 0.42 (10,66) o0.035 (0,88) MIN. 14 Places Plated through Note E PC LAYOUT 4202009/A 02/01 NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. P-suffix parts include a metal heat spreader. The heat spreader is isolated but electrically conductive, it can be grounded. N-suffix does not include a metal heat spreader. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI018A - MARCH 2001 - REVUSED FEBRUARY 2002 EEE (R-PSIP-T14) PLASTIC SINGLE-IN-LINE MODULE Suffix R 2.36 (62,48) MAX. 2.000 (50,80) 1.71 (43,43) MAX. o0.187 (4,74) 2 Places 0.41 (10,41) 0.38 (9,65) 0.59 (14,98) 0.325 (8,25) Note F 1.22 (30,98) 0.83 MAX. (21,08) 0.52 (13,20) 1 0.61 (15,49) 0.205 (5,20) 0.350 (8,89) 0.19 (4,82) 0.100 (2,54) TYP. 0.017 (0,43) TYP. 0.170 (4,31) MIN. 0.42 (10,66) MAX. 0.017 (0,43) TYP. 2.42 (61,46) 0.07 (1,77) 0.325 (8,25) 1.77 (44,95) 0.100 (2,54) 13 Places 0.040 (1,01) 0.235 (5,96) 1 0.11 (2,79) 0.42 (10,66) o0.035 (0,88) MIN. 14 Places Plated through Note E PC LAYOUT 4202010/B 02/02 NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. The metal tab is isolated but electrically conductive, it can be grounded. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI019A - MARCH 2001 - REVISED FEBRUARY 2002 EEF (R-PSIP-G14) PLASTIC SINGLE-IN-LINE MODULE Suffix F 0.040 (1,01) Note J 2.36 (62,48) MAX. 0.325 (8,25) 2.000 (50,80) 1.71 (43,43) MAX. 0.71 0.38 (18,07) (9,65) 0.59 (14,98) o0.187 (4,74) 2 Places 0.41 (10,41) 0.19 (4,82) 0.210 (5,33) 1.22 (30,98) 0.83 MAX. (21,08) 0.87 (22,11) Note F 0.52 (13,20) 1 0.61 (15,49) 0.205 (5,20) 0.350 (8,89) 0.19 (4,82) 0.100 (2,54) TYP. 0.017 (0,43) TYP. 0.080 (2,02) MIN. 0.42 (10,66) MAX. Seating Plane 0.006 (0,15) MAX. 2.42 (61,46) 2.000(50,80) 0.175 (4,44) 0.10 (2,54) 0.17 (4,32) 0.150 (3,81) 1.77 (44,95) 1.42 (30,06) 0.545 (13,84) C L toC L 0.040 (1,01) 0.325 (8,25) Note E,F Hole for #6-32 screws Note L 1.35 0.86 (34,29) (21,84) 1.120 (28,44) C 0.33 0.280 L toC L (8,38) (7,11) 0.64 Note G 0.040 (1,01) 14 Places (16,25) 0.100 (2,54) 13 Places 0.235 (5,97) 0.350 (8,89) 0.085 (2,16) PC LAYOUT NOTES: A. B. C. D. E. F. 0.017 (0,43) TYP. 0.080 (2,03) 2 Places Note H Note K 0.210 (5,33) 0.38 (9,65) 4202011/B 02/02 All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are" 0.030 (" 0, 76 mm). 3-place decimal are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. The metal tab is isolated but electrically conductive. No signal traces are allowed under the metal tab area. A solid copper island is recommended, which may be grounded. G. Power pin connections should utilize two or more vias per input, ground and output pin. POST OFFICE BOX 655303 0-7 Gage Plane H. Minimum copper land area required for solder tab. Vias are recommended to improve copper adhesion or connect land to other ground area.I J. Underside solder tabs detail. K. Solder mask openings to copper island for solder joints to mechanical pins. L. No copper, power or signal traces in this area. * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI020 - MARCH 2001 EEL (R-PSIP-G14) PLASTIC SINGLE-IN-LINE MODULE 0.040 (1,01) Note J 0.38 (9,65) 1.71 (43,43) MAX. 0.71 (18,07) 0.59 (14,98) 0.042 (1,06) 0.036 (0,91) 0.19 (4,82) 0.210 (5,33) Note F 1.22 (30,98) MAX. 0.87 (22,11) 0.52 (13,20) 1 0.080 (2,02) MIN. 0.100 (2,54) TYP. 0.205 (5,20) 0.017 (0,43) TYP. 0.42 (10,66) MAX. Seating Plane 0.006 (0,15) MAX. 0.040 (1,01) 0.175 (4,44) 1.77 (44,95) 1.42 (30,06) 0-7 Gage Plane Note E 0.017 (0,43) TYP. 0.080(2,03) 2 Places 0.10 (2,54) 0.17 (4,32) 0.150 (3,81) 0.545 (13,84) C L toC L Note L Note H 1.35 1.120 (34,29) (28,44) C L to C L Note G 0.035 (0,88) 14 Places 0.100 (2,54) 13 Places 0.235 (5,97) 0.085 (2,16) 0.210 (5,33) 0.38 (9,65) PC LAYOUT NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place decimals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. The metal tab is isolated but electrically conductive. No signal traces are allowed under the metal tab area. A solid copper island is recommended, which may be grounded. G. Power pin connections should utilize two or more vias per input, ground and output pin. POST OFFICE BOX 655303 Note K 0.33 0.280 (8,38) (7,11) 4202012/A 02/01 Minimum copper land area required for solder tab. Vias are recommended to improve copper adhesion or connect land to other ground area. J. Underside solder tabs detail K. Solder mask openings to copper island for solder joints to mechanical pins. L. No copper, power or signal traces in this area. H. * DALLAS, TEXAS 75265 1 MECHANICAL DATA MPSI021 - MARCH 2001 EEM (R-PSIP-T14) PLASTIC SINGLE-IN-LINE MODULE 0.73 (18,54) 0.210 (5,33) 0.040 (1,01) Note G 0.38 (9,65) 1.71 (43,43) MAX. 0.59 (14,98) 0.040 (1,01) 0.042 (1,06) 0.036 (0,91) 0.032 (0,81) 1.22 (30,98) MAX. Note G 0.52 (13,20) 1.040 (26,41) CL to CL 1 0.017 (0,43) TYP. 0.040 (1,01) 0.205 (5,20) 0.100 (2,54) TYP. 0.140 (3,55) MIN. 0.42 (10,66) MAX. 0.017 (0,43) TYP. 1.77 (44,95) 0.175 (4,44) 1.42 (30,06) o0.070 (1,77) MIN. 2 Places Plated through Note E 0.210 (5,33) 0.78 (19,81) 0.100 (2,54) 0.20 (5,08) 0.917 (23,29) 0.07 (1,77) 1.31 (33,27) 0.080 (2,03) 1.040 (26,41) Note F 3 Places 0.040 (1,01) o0.035 (0,88) MIN. 14 Places Plated through 0.100 (2,54) 13 Places 0.235 (5,97) PC LAYOUT NOTES: A. B. C. D. E. F. All linear dimensions are in inches (mm). This drawing is subject to change without notice. 2-place decimals are " 0.030 (" 0, 76 mm). 3-place deciamals are " 0.010 (" 0, 25 mm). Recommended mechanical keep-out area. No copper, power or signal traces in this area. POST OFFICE BOX 655303 4202013/A 02/01 G. The metal tab is isolated but electrically conductive. No signal traces are allowed under the metal tab area. A solid copper island is recommended, which may be grounded to the two underside pins. * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated