New Models Now Available! IDEC Flush Mount & 16mm LB Series Switches and Pilot Lights LB Series Design & Function Flush mount switches provide a sleek and stylish appearance. 16mm miniature switches and pilot lights with a depth of only 27.9mm accommodate smaller machines and panels. Compact Conventional product 45 mm 27.9 Single Board Mounting mm Compact Simple Short body Single board Mounting & Removable contact blocks The LB series is the shortest in the industry, only 27.9mm deep behind the panel. Reduces the size of machines and control panels. 2 Removable contacts enable easy wiring. Single board mounting reduces installation time and prevents incorrect wiring. Removable LB Series Watertight Flush Mount Degree of protection: IP65 Stylish Perfect for environments where water is sprayed under pressure such as food and beverage processing. Flush bezels project only 2 mm from the panel surface. The slim and stylish panel design enhances the appearance of any application. 2mm 3 Flush Mount Switches & Pilot Lights LB Series * Projects only 2 mm from the panel surface. * Removable contact blocks ideal for single board mounting. * Protection degree: IP65 (IEC 60529) Slim Round Actual Size 2 mm Square Rectangular Illuminated Pushbuttons Pg. 7 Illuminated Pushbuttons with Switchguard available Pushbuttons Pg. 11 Pushbuttons with Switchguard available Lens with marking plate can also be used as a pushbutton. Pilot Lights Pg. 9 Dome Pilot Lights Pg. 9 Selector Switches Non-illuminated Pg. 13 Illuminated Pg. 15 Illuminated shown 2-position and 3-position selector switches. Maintained and other spring return available. Lever shown Knob shown Key Selectors Pg. 17 Wave key Seven different keys available. Lever Switches Pg. 20 Buzzers Pg. 21 Pushbutton Color Options Illuminated Pushbutton Color Options 4 A (amber) G (green) PW (white) R (red) S (blue) Y (yellow) B (black) G (green) 16mm Miniature Switches & Pilot lights Actual Size LB Series Short * Panel depth of only 27.9 mm. * Removable contact blocks are ideal for single board mounting. * Protection degree: IP65 (IEC 60529) 27.9 mm Round Square Rectangular Illuminated Pushbuttons Pg. 7 Pushbuttons Pg. 11 Lens with marking plate can also be used as a pushbutton. Pilot Lights Pg. 9 Dome Pilot Lights Pg. 9 Selector Switches Non-illuminated Pg. 13 Illuminated Pg. 15 2-position and 3-position selector switches. Maintained and spring return available. Illuminated shown Knob shown Lever shown Key Selectors Pg. 17 Wave key Seven different keys available. Lever Switches Pg. 20 IP54 IP40 Buzzers Pg. 21 Terminal side Terminal side Bezel Options R (red) S (blue) W (white) Y (yellow) Metallic Black 5 Flush Mount & 16mm Miniature Switches & Pilot Lights Flush bezel projects only 2mm from front of panel. Standard bezel has a panel depth of only 27.9mm! Removable contact blocks are ideal for single board mounting. * Pushbuttons, lever switches, selector switches, and key selector switches with up to 3PDT contacts. * Key selectors with keys that are difficult to duplicate. Seven different key numbers to choose from. * Pilot lights with flat or dome lenses * Buzzers with 80dB steady sound * Black or metallic flush bezels available. * Bright and clear LED illuminated face. * Choice of either gold-clad or silver contacts. * Degree of protection: IP65 (from the front of the panel) File No. or Organization Contact Ratings UL508 UL Recognition No.E55996 CSA 22.2 No.14 CSA File No. LR 21451 Gold Contact (switch base color: blue) Rated Insulation Voltage Rated Thermal Current Rated Operating Voltage Rated Operating Current (resistive load) Contact Material Applicable Standards Mark TUV Rheinland EN60947-5-1 EU Low Voltage Directive GB14048.5 Specifications Operating Temperature Storage Temperature Operating Humidity Contact Resistance Insulation Resistance Dielectric Strength Switch -25 to +60C (no freezing) Illuminated units: -25 to +55C -30 to +80C (no freezing) 45 to 85% RH (no condensation) 50 mW maximum (initial value) 100 MW minimum (500V DC megger) Between live part and ground: 2,000V AC, 1 min. Between terminals of different poles: 2,000V AC, 1 min. Between terminals of the same poles: 1,000V AC, 1 min. Illumination Between live part and ground: 2,000V AC, 1 min. Vibration Resistance Shock Resistance Mechanical Life (minimum operations) Electrical Life (minimum operations) Degree of Protection Terminal Style Bezel Weight (approx.) Operating extremes/Damage limits: 5 to 55 Hz, amplitude 0.5 mm Operating extremes: 100 m/s2 Damage limits: 1,000 m/s2 Momentary: 2,000,000 Maintained: 250,000 Selector switches: 250,000 Key selector switches: 250,000 Momentary: 50,000 / 100,000 Note 1 Maintained: 50,000 / 100,000 Note 2 Selector switches: 50,000 / 100,000 Note 2 Key selector switches: 50,000 / 100,000 Note 2 IP65 (IEC 60529) Solder/tab terminal #110 PC board terminal Black plastic or metallic 11g (lever switch) 13g (pilot light, pushbutton) 14g (illuminated pushbutton, pushbutton with guard, buzzer) 15g (selector switch, illuminated pushbutton with guard) 27g (key selector switch) 1. Switching frequency 1,800 operations/h. 2. Switching frequency 1,200 operations/h. 6 250V 3A 30V DC 125V AC 0.1A 0.1A Gold-clad silver Minimum applicable load (reference value): 5V AC/DC, 1 mA Silver Contact (switch base color: gray) Rated Insulation Voltage Rated Operating Voltage Resistive load AC 50/60Hz Inductive load Resistive load DC Inductive load Rated Operating Current Resistive load AC 50/60Hz Inductive load Resistive load DC Inductive load Rated Thermal Current Contact Material 250V 30V -- -- 5A 2.5A -- -- 3A 1A 5A Silver 125V 5A 3A 1.1A 0.55A 5A 3A 0.6A 0.22A 250V 5A 1.5A -- -- 3A 1.5A -- -- AC inductive load: PF=0.6 to 0.7 DC inductive load: L/R=7 ms max. LED Ratings Rated Voltage Voltage Range LED Part No. Rated Current Voltage Rating LED Life (reference value) 5V DC 12V AC/DC 24V AC/DC 5V DC5% 12V AC/DC10% 24V AC/DC 10% LB9Z-LED1k LB9Z-LED2k LB9Z-LED5k A, R: 22 mA G, PW, S: 16 mA Marked on the side of the LED unit Approx. 30,000 hours (until the brightness reduces to 50% of the initial value) A, PW, R A, PW, R X1 X1 (+) Internal Circuit X2 (-) X2 G, S G, S X1 X1 (+) LED Chip X2 (-) Protection Diode Zener Diode Resistor X2 1. For k (color code): A (amber), G (green), PW (white), R (red), S (blue) 2. Use the white LED for yellow illumination. 3. LED lamp contains a current-limiting resistor. Varistor Illuminated Pushbuttons Illuminated Pushbuttons (Assembled) Style Operation Operating Voltage Contact Standard Bezel Flush Bezel Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) SPDT LBjL-M1T51k LBjL-M1T11Vk LBlmL-M1T51k LBlmL-M1T11Vk DPDT LBjL-M1T61k LBjL-M1T21Vk LBlmL-M1T61k LBlmL-M1T21Vk SPDT LBjL-M1T53k LBjL-M1T13Vk LBlmL-M1T53k LBlmL-M1T13Vk DPDT LBjL-M1T63k LBjL-M1T23Vk LBlmL-M1T63k LBlmL-M1T23Vk SPDT LBjL-M1T54k LBjL-M1T14Vk LBlmL-M1T54k LBlmL-M1T14Vk k Color Code Standard Bezel (black) Momentary 5V DC 12V AC/DC 24V AC/DC Flush Bezel (metallic or black) DPDT LBjL-M1T64k LBjL-M1T24Vk LBlmL-M1T64k LBlmL-M1T24Vk SPDT LBjL-A1T51k LBjL-A1T11Vk LBlmL-A1T51k LBlmL-A1T11Vk DPDT LBjL-A1T61k LBjL-A1T21Vk LBlmL-A1T61k LBlmL-A1T21Vk SPDT LBjL-A1T53k LBjL-A1T13Vk LBlmL-A1T53k LBlmL-A1T13Vk DPDT LBjL-A1T63k LBjL-A1T23Vk LBlmL-A1T63k LBlmL-A1T23Vk SPDT LBjL-A1T54k LBjL-A1T14Vk LBlmL-A1T54k LBlmL-A1T14Vk DPDT LBjL-A1T64k LBjL-A1T24Vk LBlmL-A1T64k LBlmL-A1T24Vk Maintained 5V DC Specify the color code in place of k in the Part Number: A: amber G: green R: red S: blue PW: white Y: yellow 12V AC/DC Black Bezel with Guard 24V AC/DC 1. For Standard Bezel part numbers specify: - Bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) - Lens/LED color in place of k. A (amber), G (green), PW (white), R (red), S (blue), Y (yellow) 2. For Flush Bezel part numbers specify: - Bezel shape in place of l. 6 (round), 7 (square), 8 (rectangular) - Lens/LED in place of k. A (amber), G (green), PW (white), R (red), S (blue), Y (yellow) - Bezel material in place of m. M (metallic), Blank (black), G (black with guard) 3. Solder/Tab terminals have silver contacts and PC Board Terminals have gold contacts. 4. Illuminated pushbuttons contain an LED unit. 5. See 24 for dimensions. 6. See 39 for replacement LED units. 7. Illuminated pushbuttons can be used with legend markings. Engraving can be done on a marking plate which is placed in the lens, or a clear film can be printed and placed in the lens. See 41 for details on the marking plate and film. 800.262.4332 www.IDEC.com/switches 7 Illuminated Pushbuttons Illuminated Pushbuttons (Sub-assembled) Contact Block Operator + LED Module + Contact Block Terminal Style PCB + Silver Gold Contact Part Number SPDT LB-T50 DPDT LB-T60 SPDT LB-T10V DPDT LB-T20V Style Color Amber Green Red Blue White Yellow Voltage 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V Part Number LB9Z-LED5A LB9Z-LED1A LB9Z-LED2A LB9Z-LED5G LB9Z-LED1G LB9Z-LED2G LB9Z-LED5R LB9Z-LED1R LB9Z-LED2R LB9Z-LED5S LB9Z-LED1S LB9Z-LED2S LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW Mounting Style Style Momentary Maintained Round LB1L-M0 LB1L-A0 Square LB2L-M0 LB2L-A0 Rectangular LB3L-M0 LB3L-A0 Round LB6L-M0 LB6L-A0 Flush Mount Square (Plastic) LB7L-M0 LB7L-A0 Rectangular LB8L-M0 LB8L-A0 Round LB6ML-M0 LB6ML-A0 Flush Mount Square (Metallic) LB7ML-M0 LB7ML-A0 Rectangular LB8ML-M0 LB8ML-A0 Round Flush Mount (Built-n Square switch guard) Rectangular LB6GL-M0 LB6GL-A0 LB7GL-M0 LB7GL-A0 LB8GL-M0 LB8GL-A0 Lens Style Round Square Rectangular 8 = Standard (Plastic) LED Module Style Completed Unit Operator Material Solder/Tab Lens Color Amber Green Red Blue White Yellow Amber Green Red Blue White Yellow Amber Green Red Blue White Yellow Part Number LB1A-L1A LB1A-L1G LB1A-L1R LB1A-L1S LB1A-L1W LB1A-L1Y LB2A-L1A LB2A-L1G LB2A-L1R LB2A-L1S LB2A-L1W LB2A-L1Y LB3A-L1A LB3A-L1G LB3A-L1R LB3A-L1S LB3A-L1W LB3A-L1Y Pilot Lights Pilot Lights (Assembled) Operating Voltage Style Standard Bezel Flush Bezel Solder/Tab Terminal (silver contacts) PC Board Terminal Solder/Tab Terminal PC Board Terminal (gold contacts) (silver contacts) (gold contacts) LBjP-nT01k LBjP-nT01Vk k Color Code Standard Bezel (black) 5V DC LBlmP-nT01k LBlmP-nT01Vk Specify the color code in place of k in the Part Number.: Flush Bezel (metallic or black) 12V AC/DC LBjP-nT03k LBjP-nT03Vk LBlmP-nT03k LBlmP-nT03Vk 24V AC/DC LBjP-nT04k LBjP-nT04Vk LBlmP-nT04k LBlmP-nT04Vk 1. For Standard Bezel part numbers specify: - bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) - lens/LED color in place of k. A (amber), G (green), PW (white), R (red), S (blue), Y (yellow) - lens type code in place of n. 1 (flat), 2 (dome with round lens) For Flush Bezel part numbers specify: - bezel shape in place of l. 6 (round), 7 (square), 8 (rectangular) - lens/LED in place of k. A (amber), G (green), PW (white), R (red), S (blue), Y (yellow) - bezel material in place of m. M (metallic), Blank (black) - lens type code in place of n. 1 (flat), 2 (dome with round lens) 2. Pilot lights contain an LED unit. 3. See 25 for dimensions. 4. See 41 for replacement LED unit. A: amber G: green PW: white R: red S: blue Y: yellow 800.262.4332 www.IDEC.com/switches 9 Pilot Lights Pilot Lights (Sub-assembled) Contact Block Operator + LED Module + Contact Block Lens + Completed Unit = Operator Terminal Style Style Part Number Solder Tab Mounting Style Style Standard (Plastic) LB-T00 LB-T00V PCB Flush Mount (Plastic) LED Module Style Color Amber Green Red Blue White Yellow Voltage 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V Part Number LB9Z-LED5A LB9Z-LED1A LB9Z-LED2A LB9Z-LED5G LB9Z-LED1G LB9Z-LED2G LB9Z-LED5R LB9Z-LED1R LB9Z-LED2R LB9Z-LED5S LB9Z-LED1S LB9Z-LED2S LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW Flush Mount (Metallic) Round Dome Square 800.262.4332 www.IDEC.com/switches 10 LB1P-0 Square LB2P-0 Rectangular LB3P-0 Round LB6P-0 Square LB7P-0 Rectangular LB8P-0 Round LB6MP-0 Square LB7MP-0 Rectangular LB8MP-0 Lens Style Rectangular Part Number Round Color Amber Green Red Blue White Part Number LB1A-P1A LB1A-P1G LB1A-P1R LB1A-P1S LB1A-P1W Yellow LB1A-P1Y Amber LB1A-P2A Green LB1A-P2G Red LB1A-P2R Blue LB1A-P2S White LB1A-P2W Yellow LB1A-P2Y Amber Green Red Blue White Yellow Amber Green Red Blue White Yellow LB2A-P1A LB2A-P1G LB2A-P1R LB2A-P1S LB2A-P1W LB2A-P1Y LB3A-P1A LB3A-P1G LB3A-P1R LB3A-P1S LB3A-P1W LB3A-P1Y Non-Illuminated Pushbuttons Non-Illuminated Pushbuttons (Assembled) Style Standard Bezel Flush Bezel Operation Contact Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) k Color Code Momentary Standard Bezel (black) Maintained Flush Bezel (metallic or black) SPDT LBjB-M1T5k LBjB-M1T1Vk LBlmB-M1T5k LBlmB-M1T1Vk DPDT LBjB-M1T6k LBjB-M1T2Vk LBlmB-M1T6k LBlmB-M1T2Vk 3PDT LBjB-M1T7k LBjB-M1T3Vk LBlmB-M1T7k LBlmB-M1T3Vk SPDT LBjB-A1T5k LBjB-A1T1Vk LBlmB-A1T5k LBlmB-A1T1Vk DPDT LBjB-A1T6k LBjB-A1T2Vk LBlmB-A1T6k LBlmB-A1T2Vk 3PDT LBjB-A1T7k LBjB-A1T3Vk LBlmB-A1T7k LBlmB-A1T3Vk Specify the color code in place of k in the Part Number: B: black G: green R: red S: blue W: white Y: yellow Black Bezel with Guard 1. For Standard Bezel part numbers specify: - bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) - lens/LED in place of k. B (black), G (green), R (red), S (blue), W (white), Y (yellow) 2. For Flush Bezel part numbers specify: - bezel shape in place of l. 6 (round), 7 (square), 8 (rectangular) - lens/LED in place of k. B (black), G (green), R (red), S (blue), W (white), Y (yellow) - bezel material in place of m. M (metallic), Blank (black) 3. See 26 for dimensions. 4. Lens can be used with legend markings. Engraving can be done on a marking plate which is placed into the lens, or a clear film can be printed and placed under the lens. For details on the marking plate and film, see 41. 11 Non-Illuminated Pushbuttons Non-Illuminated Pushbuttons (Sub-assembled) Contact Block Operator + Button + Contact Block Completed Unit = Operator Terminal Style Material Solder/Tab PCB Silver Gold Contact Part Number SPDT LB-T5 DPDT LB-T6 3PDT LB-T7 SPDT LB-T1V DPDT LB-T2V 3PDT LB-T3V Style Mounting style Standard (Plastic) Flush Mount (Plastic) Button Style 12 Color Black Green Red Round Blue White Yellow Black Green Red Square Blue White Yellow Black Green Red Rectangular Blue White Yellow Part Number LB1A-B1B LB1A-B1G LB1A-B1R LB1A-B1S LB1A-B1W LB1A-B1Y LB2A-B1B LB2A-B1G LB2A-B1R LB2A-B1S LB2A-B1W LB2A-B1Y LB3A-B1B LB3A-B1G LB3A-B1R LB3A-B1S LB3A-B1W LB3A-B1Y Flush Mount (Metallic) Flush Mount (Built-in switch guard) Style Momentary Maintained Round LB1L-M0 LB1L-A0 Square LB2L-M0 LB2L-A0 Rectangular LB3L-M0 LB3L-A0 Round LB6L-M0 LB6L-A0 Square LB7L-M0 LB7L-A0 Rectangular LB8L-M0 LB8L-A0 Round LB6ML-M0 LB6ML-A0 Square LB7ML-M0 LB7ML-A0 Rectangular LB8ML-M0 LB8ML-A0 Round LB6GL-M0 LB6GL-A0 Square LB7GL-M0 LB7GL-A0 Rectangular LB8GL-M0 LB8GL-A0 Selector Switches Selector Switches (Assembled) Style Standard Bezel Flush Bezel Contact Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) Operator Position Standard Bezel (black) Maintained L Spring return from right R L Maintained L C R Flush Bezel (metallic or black) Spring return from right L 45 3-position C LBjS-2nT1V LBlmS-2nT5 LBlmS-2nT1V DPDT LBjS-2nT6 LBjS-2nT2V LBlmS-2nT6 LBlmS-2nT2V 3PDT LBjS-2nT7 LBjS-2nT3V LBlmS-2nT7 LBlmS-2nT3V SPDT LBjS-21nT5 LBjS-21nT1V LBlmS-21nT5 LBlmS-21nT1V DPDT LBjS-21nT6 LBjS-21nT2V LBlmS-21nT6 LBlmS-21nT2V 3PDT LBjS-21nT7 LBjS-21nT3V LBlmS-21nT7 LBlmS-21nT3V DPDT LBjS-3nT6 LBjS-3nT2V LBlmS-3nT6 LBlmS-3nT2V 3PDT LBjS-3nT7 LBjS-3nT3V LBlmS-3nT7 LBlmS-3nT3V DPDT LBjS-31nT6 LBjS-31nT2V LBlmS-31nT6 LBlmS-31nT2V 3PDT LBjS-31nT7 LBjS-31nT3V LBlmS-31nT7 LBlmS-31nT3V DPDT LBjS-32nT6 LBjS-32nT2V LBlmS-32nT6 LBlmS-32nT2V 3PDT LBjS-32nT7 LBjS-32nT3V LBlmS-32nT7 LBlmS-32nT3V DPDT LBjS-33nT6 LBjS-33nT2V LBlmS-33nT6 LBlmS-33nT2V 3PDT LBjS-33nT7 LBjS-33nT3V LBlmS-33nT7 LBlmS-33nT3V R Spring return from left L LBjS-2nT5 R 90 2-position lever shown SPDT C R lever shown Spring return two-way L C R Knob models shown above unless otherwise indicated. 1. For Standard Bezel part numbers specify: - bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) - operator shape in place of n. blank (knob), L (lever). 2. For Flush Bezel part numbers specify: - bezel shape in place of l. 6 (round), 7 (square), 8 (rectangular) - bezel material in place of m. M (metallic), Blank (black) - operator shape in place of n. blank (knob), L (lever). 3. For contact operation, see 22. 4. For dimensions, see 28. 800.262.4332 www.IDEC.com/switches 13 Selector Switches Selector Switches (Sub-assembled) Operator Completed Unit + Contact Block Terminal Style Material Solder/Tab PCB Silver Gold Contact Part Number SPDT LB-T5 DPDT LB-T6 3PDT LB-T7 SPDT LB-T1V DPDT LB-T2V 3PDT LB-T3V + Style Shape Position Function 2 Flush Mount (Plastic) Round Contact Block 2 3 Round Knob Square 2 3 Rectangular Lever Rectangular 2 3 Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both 3 2 Square Lever Rectangular Standard (Plastic) Round 2 3 2 Flush Mount (Metallic) Round Shape Position Function 3 2 Square Knob Square Style Round Knob Part Number Knob Lever LB1S-2Y LB1S-2L LB1S-21Y LB1S-21L LB1S-3Y LB1S-3L LB1S-31Y LB1S-31L LB1S-32Y LB1S-32L LB1S-33Y LB1S-33L LB2S-2Y LB2S-2L LB2S-21Y LB2S-21L LB2S-3Y LB2S-3L LB2S-31Y LB2S-31L LB2S-32Y LB2S-32L LB2S-33Y LB2S-33L LB3S-2Y LB3S-2L LB3S-21Y LB3S-21L LB3S-3Y LB3S-3L LB3S-31Y LB3S-31L LB3S-32Y LB3S-32L LB3S-33Y LB3S-33L Square SPDT contacts applicable for 2-position switches only. Operator 3 3 Round Lever 14 Rectangular 2 3 Knob Part Number Lever Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both Maintained Spring from right LB6S-2Y LB6S-21Y LB6S-3Y LB6S-31Y LB6S-32Y LB6S-33Y LB7S-2Y LB7S-21Y LB7S-3Y LB7S-31Y LB7S-32Y LB7S-33Y LB8S-2Y LB8S-21Y LB8S-3Y LB8S-31Y LB8S-32Y LB8S-33Y LB6MS-2Y LB6MS-21Y LB6MS-3Y LB6MS-31Y LB6MS-32Y LB6MS-33Y LB7MS-2Y LB7MS-21Y LB6S-2L LB6S-21L LB6S-3L LB6S-31L LB6S-32L LB6S-33L LB7S-2L LB7S-21L LB7S-3L LB7S-31L LB7S-32L LB7S-33L LB8S-2L LB8S-21L LB8S-3L LB8S-31L LB8S-32L LB8S-33L LB6MS-2L LB6MS-21L LB6MS-3L LB6MS-31L LB6MS-32L LB6MS-33L LB7MS-2L LB7MS-21L Maintained LB7MS-3Y LB7MS-3L Spring from right Spring from left Spring from both Maintained Spring from right Maintained Spring from right Spring from left Spring from both LB7MS-31Y LB7MS-32Y LB7MS-33Y LB8MS-2Y LB8MS-21Y LB8MS-3Y LB8MS-31Y LB8MS-32Y LB8MS-33Y LB7MS-31L LB7MS-32L LB7MS-33L LB8MS-2L LB8MS-21L LB8MS-3L LB8MS-31L LB8MS-32L LB8MS-33L Illuminated Selector Switches Illuminated Selector Switches (Assembled) Style Operating Voltage Standard Bezel Flush Bezel Contact Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) Operator Position Maintained Standard Bezel (black) 90 2-position L SPDT LBjF-2T51k LBjF-2T11Vk LB6lF-2T51k LB6lF-2T11Vk DPDT LBjF-2T61k LBjF-2T21Vk LB6lF-2T61k LB6lF-2T21Vk DPDT LBjF-3T61k LBjF-3T21Vk LB6lF-3T61k LB6lF-3T21Vk SPDT LBjF-2T53k LBjF-2T13Vk LB6lF-2T53k LB6lF-2T13Vk DPDT LBjF-2T63k LBjF-2T23Vk LB6lF-2T63k LB6lF-2T23Vk DPDT LBjF-3T63k LBjF-3T23Vk LB6lF-3T63k LB6lF-3T23Vk SPDT LBjF-2T54k LBjF-2T14Vk LB6lF-2T54k LB6lF-2T14Vk DPDT LBjF-2T64k LBjF-2T24Vk LB6lF-2T64k LB6lF-2T24Vk DPDT LBjF-3T64k LBjF-3T24Vk LB6lF-3T64k LB6lF-3T24Vk R 5V DC Maintained 45 3-position L C R Maintained 90 2-position L R 12V AC/DC Maintained 45 3-position Flush Bezel (metallic or black) L C R Maintained 90 2-position L R 24V AC/DC Maintained 45 3-position L C R Flush bezel only available with round operator. 1. For Standard Bezel part numbers specify: - bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) - color code in place of k. A (amber), G (green), R (red), S (blue), PW (white), Y (yellow) 2. For Flush Bezel part numbers specify: - color code in place of k. A (amber), G (green), R (red), S (blue), PW (white), Y (yellow) - bezel material in place of l. M (metallic), Blank (black) 3. For contact operation, see 22. 4. For dimensions, see 30. 800.262.4332 www.IDEC.com/switches 15 Illuminated Selector Switches Illuminated Selector Switches (Sub-assembled) Contact Block Operator LED Module + + Contact Block Lans Handle + Completed Unit = LED Module Terminal Style Material Silver Solder/Tab Gold PCB Contact Part Number SPDT LB-T50 DPDT LB-T60 SPDT LB-T10 DPDT LB-T20 SPDT LB-T10V DPDT LB-T20V Style Color Amber Green Gold Red SPDT contacts applicable for 2-position switches only. Operator Blue Shape Position Function Round Style Part Number 2 Maintained LB1F-2 3 Maintained LB1F-3 2 Maintained LB2F-2 3 Maintained LB2F-3 2 Maintained LB3F-2 3 Maintained LB3F-3 2 Maintained LB6F-2 3 Maintained LB6F-3 2 Maintained LB6MF-2 3 Maintained LB6MF-3 White Standard (Plastic) Rectangular Square Yellow Round Flush Mount (Plastic) Round Flush Mount (Metallic) Voltage 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V 5V 12V 24V Part Number LB9Z-LED5A LB9Z-LED1A LB9Z-LED2A LB9Z-LED5G LB9Z-LED1G LB9Z-LED2G LB9Z-LED5R LB9Z-LED1R LB9Z-LED2R LB9Z-LED5S LB9Z-LED1S LB9Z-LED2S LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW LB9Z-LED5PW LB9Z-LED1PW LB9Z-LED2PW Lens Handle Style Color Amber Green Red Blue White Yellow Part Number LA1A-FA LA1A-FG LA1A-FR LA1A-FS LA1A-FW LA1A-FY 800.262.4332 www.IDEC.com/switches 16 Key Selector Switches Key Selector Switches (Assembled) Style Operator Position Key retained at j 90 2-position Standard Bezel (black) Maintained A B Spring return from right C B A L R L R L R L L R C R Flush Bezel (metallic or black) B Maintained 45 3-position C D E G H L L L L L L C C C C C C R R R R R R Standard Bezel Flush Bezel Contact Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) SPDT LBjK-2T5A LBjK-2T1VA LBlmK-2T5A LBlmK-2T1VA DPDT LBjK-2T6A LBjK-2T2VA LBlmK-2T6A LBlmK-2T2VA 3PDT LBjK-2T7A LBjK-2T3VA LBlmK-2T7A LBlmK-2T3VA SPDT LBjK-2T5B LBjK-2T1VB LBlmK-2T5B LBlmK-2T1VB DPDT LBjK-2T6B LBjK-2T2VB LBlmK-2T6B LBlmK-2T2VB 3PDT LBjK-2T7B LBjK-2T3VB LBlmK-2T7B LBlmK-2T3VB SPDT LBjK-2T5C LBjK-2T1VC LBlmK-2T5C LBlmK-2T1VC DPDT LBjK-2T6C LBjK-2T2VC LBlmK-2T6C LBlmK-2T2VC 3PDT LBjK-2T7C LBjK-2T3VC LBlmK-2T7C LBlmK-2T3VC SPDT LBjK-21T5B LBjK-21T1VB LBlmK-21T5B LBlmK-21T1VB DPDT LBjK-21T6B LBjK-21T2VB LBlmK-21T6B LBlmK-21T2VB 3PDT LBjK-21T7B LBjK-21T3VB LBlmK-21T7B LBlmK-21T3VB DPDT LBjK-3T6A LBjK-3T2VA LBlmK-3T6A LBlmK-3T2VA 3PDT LBjK-3T7A LBjK-3T3VA LBlmK-3T7A LBlmK-3T3VA DPDT LBjK-3T6B LBjK-3T2VB LBlmK-3T6B LBlmK-3T2VB 3PDT LBjK-3T7B LBjK-3T3VB LBlmK-3T7B LBlmK-3T3VB DPDT LBjK-3T6C LBjK-3T2VC LBlmK-3T6C LBlmK-3T2VC 3PDT LBjK-3T7C LBjK-3T3VC LBlmK-3T7C LBlmK-3T3VC DPDT LBjK-3T6D LBjK-3T2VD LBlmK-3T6D LBlmK-3T2VD 3PDT LBjK-3T7D LBjK-3T3VD LBlmK-3T7D LBlmK-3T3VD DPDT LBjK-3T6E LBjK-3T2VE LBlmK-3T6E LBlmK-3T2VE 3PDT LBjK-3T7E LBjK-3T3VE LBlmK-3T7E LBlmK-3T3VE DPDT LBjK-3T6G LBjK-3T2VG LBlmK-3T6G LBlmK-3T2VG 3PDT LBjK-3T7G LBjK-3T3VG LBlmK-3T7G LBlmK-3T3VG DPDT LBjK-3T6H LBjK-3T2VH LBlmK-3T6H LBlmK-3T2VH 3PDT LBjK-3T7H LBjK-3T3VH LBlmK-3T7H LBlmK-3T3VH Assembled Key Selector Switches con't on next page. 17 Key Selector Switches Key Selector Switches con't Style Operator Position Standard Bezel Flush Bezel Contact Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) Key retained at j Standard Bezel (black L C R DPDT LBjK-31T6B LBjK-31T2VB LBlmK-31T6B LBlmK-31T2VB 3PDT LBjK-31T7B LBjK-31T3VB LBlmK-31T7B LBlmK-31T3VB DPDT LBjK-31T6D LBjK-31T2VD LBlmK-31T6D LBlmK-31T2VD 3PDT LBjK-31T7D LBjK-31T3VD LBlmK-31T7D LBlmK-31T3VD DPDT LBjK-31T6G LBjK-31T2VG LBlmK-31T6G LBlmK-31T2VG 3PDT LBjK-31T7G LBjK-31T3VG LBlmK-31T7G LBlmK-31T3VG DPDT LBjK-32T6C LBjK-32T2VC LBlmK-32T6C LBlmK-32T2VC 3PDT LBjK-32T7C LBjK-32T3VC LBlmK-32T7C LBlmK-32T3VC DPDT LBjK-32T6D LBjK-32T2VD LBlmK-32T6D LBlmK-32T2VD 3PDT LBjK-32T7D LBjK-32T3VD LBlmK-32T7D LBlmK-32T3VD DPDT LBjK-32T6H LBjK-32T2VH LBlmK-32T6H LBlmK-32T2VH 3PDT LBjK-32T7H LBjK-32T3VH LBlmK-32T7H LBlmK-32T3VH DPDT LBjK-33T6D LBjK-33T2VD LBlmK-33T6D LBlmK-33T2VD 3PDT LBjK-33T7D LBjK-33T3VD LBlmK-33T7D LBlmK-33T3VD Spring return from right B L C R D L C R L C R C Spring return from left Flush Bezel (metallic or black) 45 3-position G L C R D L C R Spring return two-way H L C R D Key is retained at j and removable at positions. Two keys are supplied. For Standard Bezel part numbers specify bezel shape in place of j. 1 (round), 2 (square), 3 (rectangular) For Flush Bezel part numbers specify: -bezel shape in place of l. 6 (round), 7 (square), 8 (rectangular) - bezel material in place of m. M (metallic), Blank (black) 5. For contact operation, see 22. 6. For dimensions, see 31. 7. For additional security, wave keys also available. Add the letter "S" before the "T" in the part no. Example: LB1K-31ST1A Besides the standard wave key (key number 0H), six other keys are available. To order other keys, specify the key number as shown below: Example: LB1K-31ST2B-1H (Key number is indicated on the key cylinder. Standard keys do not have a key number indication.) 1. 2. 3. 4. (blank): Standard wave key (0H) 1H to 2H: Reversible wave key 3H to 6H: Non-reversible wave key 8. If ordering standard wave key (0H), subcomponents are available, see next page. 9. If ordering other than standard wave key (for example, key number 6H), only completed switches are available. 800.262.4332 www.IDEC.com/switches 18 Key Selector Switches Key Selector Switches (Sub-assembled) Contact Block Operator + Completed Unit = Contact Block Style Terminal Style Material Solder/Tab PCB Silver Gold Contact Part Number SPDT LB-T5 DPDT LB-T6 3PDT LB-T7 SPDT LB-T1V DPDT LB-T2V 3PDT LB-T3V Style Position Function 2 Maintained 3 3 2 3 LB1K-2n 2 LB1K-3n 2 Spring from right LB1K-31n 3 3 LB2K-2n LB2K-3n 2 Spring from left LB2K-32n Maintained Rectangular 3 3 LB3K-2n Spring from right LB3K-21B 2 Spring from right LB3K-31n Spring from both LB3K-33D LB7K-3n Spring from right LB7K-31n Spring from left LB7K-32n Maintained LB8K-2n Spring from right LB8K-21B LB8K-3n Spring from right LB8K-31n Spring from left LB8K-32n Maintained LB6MK-2n Spring from right LB6MK-21B LB6MK-3n Spring from right LB6MK-31n Spring from left LB6MK-32n Spring from both LB6MK-33D Flush Mount (metallic) LB3K-3n Spring from left LB3K-32n LB7K-2n Spring from right LB7K-21B Maintained Round Spring from both LB2K-33D 2 Maintained Spring from both LB8K-33D Spring from right LB2K-31n Maintained Spring from left LB6K-32n Maintained Rectangular Spring from right LB2K-21B Maintained Square LB6K-3n Spring from right LB6K-31n Spring from both LB7K-33D Spring from left LB1K-32n Maintained Spring from right LB6K-21B Maintained Square Spring from both LB1K-33D Standard (plastic) Part number LB6K-2n Spring from both LB6K-33D Flush Mount (plastic) Part number Maintained Maintained Round Spring from right LB1K-21B Maintained Round Position Function 2 Operator Style Style Maintained Maintained Square 3 LB7MK-2n Spring from right LB7MK-21B LB7MK-3n Spring from right LB7MK-31n Spring from left LB7MK-32n Spring from both LB7MK-33D 2 Maintained Spring from right LB8MK-21B Maintained Rectangular 3 LB8MK-2n LB8MK-3n Spring from right LB8MK-31n Spring from left LB8MK-32n Spring from both LB8MK-33D 1. In place of n specify retention option code from table below. 2. For standard wave key operators, add "S" to part number before the key retention code from table below. (For example, LB6K-2B with wave key would be LB6K-2SB.) n Retention Option Code Code A B C D Description Key not retained in any position (Removable in all positions) Key retained in right position only Key retained in left position only Code E G H Description Key retained in center only (3 position only) Key retained in right and center (3 position only) Key retained in left and center (3 position only) Key retained in left and right (3 position only) 19 Lever Switches Lever Switches (Assembled) Style Operator Position Maintained Standard Bezel (black) 2-position Solder/Tab Terminal (silver contacts) PC Board Terminal (gold contacts) SPDT LBjT-2T5 LBjT-2T1V DPDT LBjT-2T6 LBjT-2T2V 3PDT LBjT-2T7 LBjT-2T3V DPDT LBjT-3T2 LBjT-3T6V 3PDT LBjT-3T3 LBjT-3T7V DPDT LBjT-33T2 LBjT-33T6V 3PDT LBjT-33T3 LBjT-33T7V U D Maintained Contact U C Flush Bezel (metallic or black) D 3-position Spring return from top/bottom U C D 1. For all part numbers specify bezel in place of j. 1 (standard bezel), 6 (flush bezel). 2. For contact operation, see 22. 3. For dimensions, see 33. Lever Switches (Sub-assembled) Contact Block Operator Completed Unit + = Contact Block Terminal Style Operator Material Silver Solder/Tab Gold PCB Gold Contact Part Number SPDT LB-T5 DPDT LB-T6 3PDT LB-T7 SPDT LB-T1 DPDT LB-T2 3PDT LB-T3 SPDT LB-T1V DPDT LB-T2V 3PDT LB-T3V Style Round Standard (Plastic) Part Number 2 Maintained LB1T-2 Maintained LB1T-3 Spring rerturn from both LB1T-33 Maintained LB6T-2 Maintained LB6T-3 Spring return from both LB6T-33 3 Round Flush Mount (Plastic) 2 3 800.262.4332 www.IDEC.com/switches 20 Position Function Lever Switches Buzzers (Assembled) Standard Bezel Style Shape Voltage Flush Bezel Solder/Tab Terminal PC Board Terminal Solder/Tab Terminal PC Board Terminal (silver contacts) (gold contacts) (silver contacts) (gold contacts) Black Bezel 12V DC - - LB6Z-1T03 LB6Z-1T03V 24V DC - - LB6Z-1T04 LB6Z-1T04V 12V DC LB3Z-1T03 LB3Z-1T03V LB8Z-1T03 LB8Z-1T03V 24V DC LB3Z-1T04 LB3Z-1T04V LB8Z-1T04 LB8Z-1T04V 12V DC - - LB6MZ-1T03 LB6MZ-1T03V 24V DC - - LB6MZ-1T04 LB6MZ-1T04V 12V DC - - LB8MZ-1T03 LB8MZ-1T03V 24V DC - - LB8MZ-1T04 LB8MZ-1T04V Round Rectangular Metallic Bezel Round Rectangular 1. IP54 Rated. 2. For IP40 rating use part number LB3Z-104K. 3. For dimensions, see 34. Buzzers (Sub-assembled) Contact Block Operator Completed Unit + Contact Block Terminal Style Operator Part Number Solder/Tab PCB = Style Voltage 24V DC Mounting Style Shape LB-T00 Standard (Plastic) Rectangular LB3Z-103 LB3Z-104 Round LB6Z-103 LB6Z-104 LB-T00V Flush Mount (Plastic) Rectangular LB8Z-103 LB8Z-104 Round LB6MZ-103 LB6MZ-104 Rectangular LB8MZ-103 LB8MZ-104 Flush Mount shown Flush Mount (Metallic) 12V DC 21 Contact Operations & Dimensions (mm) Contact Operation Selector Switch, Illuminated Selector Switch, Key Selector Switch Operator Position & Contact Operation (Top View) Position Left Contact 14 Center Right 12 14 SPDT 11 90 2-position L R R L DPDT Spring return from right Maintained 12 11 Left 14 12 Right 24 22 11 21 Left 14 12 Right 24 22 11 21 Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 3PDT 11 21 11 31 Left 14 12 Right 24 22 11 21 Left 14 12 Right 24 22 11 21 21 31 Left 14 12 Right 24 22 11 21 DPDT 45 3-position L C R Maintained L C R C L L C R R Spring return from Spring return from Spring return tworight left way Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 11 11 11 3PDT 21 31 21 31 21 31 Lever Switch Lever Position & Contact Operation (Top View) Position Contact Down 14 Center Up 12 14 12 SPDT 11 U 90 2-position 11 Left 14 12 Right 24 22 11 21 Left 14 12 Right 24 22 11 21 DPDT D Maintained Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 3PDT 11 45 3-position U U C C D D Maintained 21 31 11 Left 14 12 Right 24 22 11 21 Left 14 12 Right 24 22 11 21 21 31 Left 14 12 Right 24 22 11 21 DPDT Spring return two-way Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 Left Center Right 14 12 24 22 34 32 11 11 11 3PDT 21 31 21 31 21 31 Mounting Hole Layout (mm) Flush Bezels 18 1 22 *1. Rectangular: 24 mm22 1 3PDT: 23.2 mm *2. 3PDT: 21 mm 22 1 18.2 +0 0 .2 22 1 When using the LB series with a rubber boot or terminal cover, make sure to note the dimensions on 37 and 38. +0.2 0 18.2 22 1 +0.2 0 22 1 18.2 22 1 +0.2 0 24.2 28 +0.2 0 18.2 +0.2 0 2 24.2 +0.2 0 24.2 22 2 8. 18.2 +0.2 0 o1 +0 0 .2 18.2 +0.2 0 2 Rectangular 22 2 8. 22 2 o1 +0 0 .2 22 2 2 22 2 8. 22 2 o1 +0 .2 0 18 6.2 22 2 o1 Square 22 2 Round LB1/LB2/LB3 22 2 Standard Bezels 28 *1. 3PDT: 23.2 mm28 *2. Switches with Guard: 45 mm +0.2 0 Dimensions (mm) PC Board Drilling Layout (mm) Notes for Designing PC Board and Circuit Use 1.6-mm-thick glass epoxy PC board with drilled holes. Design a circuit so that the LB series can operate within the rated voltage and current range. Make sure that inrush current and voltage do not exceed the rating. Minimum applicable load is 5V AC/DC, 1mA on gold contacts. Since the *2.8-mm-wide terminal touches the PC board as shown below , short circuit may occur with pattern lines. Design a circuit that prevents short circuits. 8 8 8 8 (0.5) (0.5) 2.8 2.8 2.8 2.8 Soldered Soldered Side Side Mounting Mounting Side Side Switch terminal 1.6 (PC1.6 Board) (PC Board) 5 2.4 2.4 SW Terminal SW Terminal (0.8) (0.8) SW Terminal SW Terminal SW Terminal SW Terminal 9 9- -o1 o1 .2 .2 +0 +0 0 .1 0 .1 5 5 5 NC Terminal NC Terminal NO Terminal NO Terminal COM Terminal COM Terminal 2.8 2.8 2.4 2.4 5 5 5 5 6.0 6.0 2.4 2.4 Mounting Mounting Side Side Lamp terminal (0.8) (0.8) (0.8) (0.8) (0.5) (0.5) (0.5) (0.5) Soldered Soldered Side Side 2.8 2.8 2.8 2.8 3PDT Contacts NC Terminal NC Terminal NO Terminal NO Terminal COM Terminal COM Terminal SW Terminal SW Terminal DPDT DPDT Lamp Terminal Lamp Terminal SW Terminal SW Terminal SPDT SPDT (0.8) (0.8) 9 9- -o1 o1 .2 + .2 +0 0 0.1 0 .1 (0.8) (0.8) Lamp Terminal (+) LampTerminal Terminal(-) (+) Lamp Lamp Terminal (-) 1.6 1.6 (PC Board) (PC Board) 1.6 1.6 (PC Board) (PC Board) 2.8 2.8 4.0 4.0 (0.8) (0.8) (0.8) (0.8) (0.8) (0.8) 6.95 (0.5) 6.95 (0.5) 2.8 2.8 3.85 (0.5) 3.85 (0.5) (0.5) (0.5) 2.8 2.8 SPDT/DPDT Contacts 2.4 2.4 1. 2. 3. 4. Soldered Soldered Side Side Mounting Mounting Side Side PC Board Drilling Layout (Bottom View) 3PDT Contacts .2 o1 8- le ho r d ng ve ir lle rati g le ) 3 d e in o6 op ck ote 0.5 for e lo (N th 9- o1 .2 (N e ot 5 9.3 (N ot e 1.45 2) le ho r ed g rill ratin leve d o6 ope king te 3) r c o fo e lo (N th 5 SPDT/DPDT Contacts 1 (Note 1) 1 ( Note 1) 5 5 10 2) 3.85 1.95 (Note 1) 8 6.95 8 1. When designing, note the alignment of the center lines of the contact blocks and operators. 2. The diameter of the terminal hole is o1.2. 3. Hole diameter may vary to meet installation requirements. Determine the location and the size of the hole so that the locking lever can be operated. 800.262.4332 www.IDEC.com/switches 23 Dimensions (mm) Illuminated Pushbutton Standard Bezels 1 Panel Thickness: 0.5 to 3.2 mm Gasket 2.6 8 o1 3.85 3.85 1.2 Round 5.7 Locking Ring 2-R0.6 6.95 6.95 Square Solder/Tab Terminal Mounting Ring 0.6 18 0.8W x 0.5t 2.8W x 0.5t 18 6 1 Rectangular 3 6 5 5 17.8 15.8 3 1 LOCK 2 5.5 7 [PC Board Terminal] Panel Thickness: 0.5 to 3.2 mm Panel Thickness: 0.5 to 3.2 mm Gasket 2.6 24 9 [Solder/Tab Terminal] Flush Bezels SPDT/DPDT Contacts Round Gasket Locking Ring 1.2 Round 2 o2 o22 3.85 3.85 1 8.8 20.9 11 22.5 17.8 2-R0.6 Square Square 22 22 11 22.5 Mounting Bracket 6.95 6.95 Solder/Tab Terminal 24.2 0.8W x 0.5t LOCK 5.5 [PC Board Terminal] 7 27.9 2 [Solder/Tab Terminal] 2 5.2 [With Guard] Terminal Arrangement (Bottom View) Illuminated Pushbuttons 24 24 Lamp Lamp Terminal Terminal (-) (-) 21 21 12 12 X1 X1 14 14 X2 X2 11 11 (SPDT contacts on the only) (SPDT contacts on the rightright only) 24 Pilot Lights TOPTOP 22 22 11 22.5 22 30.4 6 3 2 17.8 Lamp Lamp Terminal Terminal (+) (+) Rectangular 1 Rectangular 6 5 5 15.8 17.8 3 1 2.8W x 0.5t TOPTOP Lamp Lamp Terminal Terminal (+) (+) Lamp Lamp Terminal Terminal (-) (-) X1 X1 X2 X2 28 28 [With Guard] Dimensions (mm) Pilot Lights Standard Bezels Panel Thickness: 0.5 to 3.2 mm Gasket 1 2.6 1.2 Locking Ring Round 8 o1 5.7 2-R0.6 Square Solder/Tab Terminal Mounting Ring 0.6 18 18 3 3 Rectangular 3 3 15.8 17.8 2.8W x 0.5t 0.8W x 0.5t LOCK 2 17.8 8.8 7 5.5 [PC Board Terminal] 20.9 24 9 [Flush] [Solder/Tab Terminal] [Dome] 14.4 5.7 [Dome] Flush Bezels Panel Thickness: 0.5 to 3.2 mm Round Gasket 2.6 1 2 Locking Ring 2-R0.6 1.2 o2 Square Solder/Tab Terminal Mounting Bracket 22 0.8W x 0.5t Rectangular 2.8W x 0.5t 3 3 22 17.8 15.8 3 3 LOCK 17.8 2 5.5 [PC Board Terminal] 7 2 27.9 [Flush, Solder/Tab Terminal] 28 [Flush] [Dome] 7.4 2.0 800.262.4332 www.IDEC.com/switches [Dome] 25 Dimensions (mm) Non-Illuminated Pushbuttons Standard Bezels 2.6 1 Panel Thickness: 0.5 to 3.2 mm Gasket 1.2 5.7 3.85 3.85 Locking Ring 2-R0.6 Solder/Tab Terminal 6.95 6.95 Round Mounting Ring 8 o1 0.6 1.95 8 Square 8 8 8 1.95 [SPDT/DPDT] [3PDT] 18 0.8W x 0.5t [SPDT/DPDT] 1 Rectangular 18 6 2 17.8 2.8W x 0.5t 6 5 5 15.8 17.8 1 LOCK 5.5 [PC Board Terminal] 8.8 7 24 20.9 9 [Solder/Tab Terminal] 20.8 18.8 11.9 LOCK 11.1 23 [3PDT] Terminal Arrangement (Bottom View) SPDT/DPDT Contacts 3PDT Contacts TOP TOP TOP TOP 22 2212 12 32 22 32 12 22 12 24 2414 14 34 24 34 14 24 14 21 2111 11 31 21 31 11 21 11 (SPDT contacts on the right only) (SPDT contacts on the right only) 26 Dimensions (mm) Non-Illuminated Pushbuttons Flush Bezels 2.6 Panel Thickness: 0.5 to 3.2 mm Gasket Gasket Locking Ring 1.2 3.85 3.85 1 Panel Thickness: 0.5 to 3.2 mm 2-R0.6 Mounting Bracket 6.95 6.95 Solder/Tab Terminal [SPDT/DPDT] Round Round 2 o2 8 [3PDT] 11 24.2 22 0.8W x 0.5t 2.8W x 0.5t [SPDT/DPDT] 5.5 [PC Board Terminal] 22 30.4 6 2 11 22.5 1 Rectangular 2 7 27.9 2 [Solder/Tab Terminal] 5.2 [With Guard] 28 28 [With Guard] 20.8 18.8 11.9 LOCK 22 Rectangular 6 5 5 15.8 17.8 1 LOCK 17.8 22.5 Square 22.5 Square 8 8 8 11 1.95 1.95 o22 11.1 23 [3PDT] 800.262.4332 www.IDEC.com/switches 27 Dimensions (mm) Selector Switches Standard Bezels Panel Thickness: 0.5 to 3.2 mm Gasket 1.2 3.85 2.6 1 3.85 Locking Ring 2-R0.6 6.95 Solder/Tab Terminal 6.95 Round Mounting Ring Round 8 o1 8 o1 0.6 1.95 1.95 [SPDT/DPDT] 8 8 8 8 Square Square [3PDT] 0.8W x 0.5t 18 1 10.9 6 [PC Board Terminal] 8.8 7 8.7 20.9 [Knob Operator PC Board Terminal] 11.9 20.8 18.8 8.7 18.1 11.1 [Lever Operator] 23 24 24 15.5 LOCK [3PDT] 800.262.4332 www.IDEC.com/switches 28 18 18 5 2 5.5 [SPDT/DPDT] Rectangular 6 1 Rectangular 5 17.8 15.8 17.8 18 2.8W x 0.5t LOCK [Knob Operator] [Lever Operator] Dimensions (mm) Selector Switches Flush Bezels Panel Thickness: 0.5 to 3.2 mm Gasket Locking Ring 1.2 3.85 2.6 3.85 1 Round 2-R0.6 2 Round Solder/Tab Terminal 2 o2 Mounting Bracket 6.95 6.95 o2 1.95 1.95 [SPDT/DPDT] Square 8 8 8 8 Square [3PDT] 0.8W x 0.5t Rectangular 22 22 6 6 5.5 [SPDT/DPDT] Rectangular 1 1 5 5 17.8 15.8 2 17.8 22 22 2.8W x 0.5t LOCK [PC Board Terminal] 2 7 8.5 27.9 [Knob Operator PC Board Terminal] 28 [Knob Operator] 28 [Lever Operator] 20.8 18.8 11.9 LOCK 2 11.1 11.1 23 [3PDT] [Lever Operator] Terminal Arrangement (Bottom View) SPDT/DPDT Contacts TOP 22 24 21 22 24 21 3PDT Contacts TOP 12 14 11 TOP 12 14 11 TOP 32 32 22 22 12 12 34 34 24 24 14 14 31 31 21 21 11 11 contacts on the right only) (SPDT (SPDT contacts on the right only) 29 Dimensions (mm) Illuminated Selector Switches Standard Bezels Panel Thickness: 0.5 to 3.2 mm 2.6 1 1.2 2-R0.6 Round 8 o1 3.85 3.85 Gasket Locking Ring Solder/Tab Terminal LOCK 6.95 6.95 Square Mounting Ring 0.8W x 0.5t 0.6 2.8W x 0.5t 1 1 6 18 3 6 5 5 17.8 15.8 3 18 Rectangular 17.8 2 5.5 9.6 7 20.9 17.5 24 [Solder/Tab Terminal] [PC Board Terminal] Flush Bezels 1 Panel Thickness: 0.5 to 3.2 mm 2.6 Gasket 3.85 3.85 6.95 1.2 2-R0.6 6.95 Locking Ring Solder/Tab Terminal Mounting Bracket 0.8W x 0.5t LOCK 2.8W x 0.5t 2 1 o2 6 1 3 5 6 5 17.8 15.8 3 2 17.8 Round 5.5 7 2.4 27.9 10.3 [PC Board Terminal] [Solder/Tab Terminal] Terminal Arrangement (Bottom View) Lamp Terminal (+) TOP 22 TOP 12 X1 24 Lamp Terminal (-) 14 X2 21 11 (SPDT contacts on the right only) 30 Lamp Terminal (+) Lamp Terminal (-) 800.262.4332 www.IDEC.com/switches X1 X2 Dimensions (mm) Key Selector Switches Standard Bezels With Wave Key Locking Ring 3.85 8 8 8 8 8 8 1 Rectangular 6 14 1 6 8.8 10.2 [Solder/Tab Terminal] 20.9 7 [Solder/Tab Terminal] Key No. :N/A to 2H 31.3 18 24 Key No. :N/A to 2H Key No. :3H to 6H 11.9 11.1 23 8.5 11.9 8.5 5.5 [PC Board Terminal] 24 31.3 5.5 2 10.2 20.9 7 5.5 14 6 6 5 8.8 [PC Board Terminal] LOCK 18.8 18 1 5 1 5 15.8 2 17.8 LOCK 20.8 18 2.8W x 0.5t 5.5 [SPDT/DPDT] 18.8 Rectangular 2.8W x 0.5t [3PDT] [SPDT/DPDT] 20.8 Square 0.6 Square 0.8W x 0.5t 5 15.8 17.8 17.8 17.8 8 o1 0.6 Mounting Ring 0.8W x 0.5t LOCK 8 o1 18 [3PDT] 8 LOCK Mounting Ring 1.95 6.95 [SPDT/DPDT] 1.95 8 Solder/Tab Terminal Round 6.95 6.95 [SPDT/DPDT] 6.95 1.95 1.2 Solder/Tab Terminal 2-R0.6 Round 1.95 1.2 2-R0.6 Locking Ring 3.85 3.85 3.85 2.6 1 Panel Thickness: 0.5 to 3.2 mm Gasket 2.6 1 Panel Thickness: 0.5 to 3.2 mm Gasket Key No. :3H to 6H 11.1 [3PDT] 23 Locking Ring With Standard Key 1.2 3.85 Locking Ring Round 3.85 3.85 3.85 2.6 1 Panel Thickness: 0.5 to 3.2 mm Gasket 2.6 1 Panel Thickness: 0.5 to 3.2 mm Gasket [3PDT] Round Solder/Tab Terminal Mounting Ring [SPDT/DPDT] 8 o1 0.6 Square Mounting Ring 1.95 6.95 [SPDT/DPDT] 6.95 1.95 1.2 Solder/Tab Terminal 2-R0.6 6.95 6.95 2-R0.6 8 o1 0.6 1.95 8 8 8 8 8 1.95 8 Square 18 8 1 1 6 1 6 2 5.5 2 [PC Board Terminal] 5.5 [PC Board Terminal] 8.8 9 24 20.9 7 25.1 8.8 7 9 [Solder/Tab Terminal] 20.9 18 6 6 1 18 5 Rectangular 24 25.1 [Solder/Tab Terminal] 11.9 11.9 18.8 20.8 LOCK 5 15.8 17.8 LOCK [SPDT/DPDT] 18 2.8W x 0.5t 0.8W x 0.5t 5 5 15.8 17.8 17.8 17.8 [SPDT/DPDT] 18.8 [3PDT] Rectangular 2.8W x 0.5t 0.8W x 0.5t LOCK 20.8 [3PDT] 8 LOCK 11.1 23 11.1 [3PDT] 23 [3PDT] 31 Dimensions (mm) Key Selector Switches Flush Bezels With Wave Key 1 Gasket 3.85 3.85 2.6 Panel Thickness: 0.5 to 3.2 mm Locking Ring 3.85 3.85 2.6 1 Panel Thickness: 0.5 to 3.2 mm Locking Ring Gasket Round 1.2 2-R0.6 Round 2 o2 2 o2 6.95 1.95 6.95 1.95 Mounting Bracket Mounting Bracket [SPDT/DPDT] [SPDT/DPDT] Square Square 8 8 8 8 8 8 8 Solder/Tab Terminal 8 6.95 1.95 6.95 1.95 1.2 2-R0.6 Solder/Tab Terminal [3PDT] [3PDT] LOCK [3PDT] 1 14 22 14 1 6 6 6 6 2 2 5.52 7 27.9 7 27.9 [Solder/Tab Terminal] 5.5 [PC Board Terminal] [Solder/Tab Terminal] [PC Board Terminal] 28 24.3 2 Key 24.3 No. :N/A to 2H 28 Key No. :N/A to 2H Key No. :3H to 6H With Standard Key 1 1.2 2.6 3.85 3.85 3.85 3.85 2.6 1 Thickness: Key Panel No. :3H to 6H 0.5 to 3.2 mm Panel Thickness: 0.5 to 3.2 mm Gasket Locking Ring Gasket Locking Ring Round 2-R0.6 1.2 8.5 8.5 5.5 [SPDT/DPDT] 1 11.1 23 11.1 [3PDT] 23 Rectangular 5.5 17.8 5 5 5 5 20.8 20.8 18.8 18.8 11.9 11.9 17.8 17.8 15.8 15.8 17.8 [SPDT/DPDT] Rectangular 22 2.8W x 0.5t 0.8W x 0.5t 1 LOCK 22 2.8W x 0.5t 0.8W x 0.5t 22 LOCK LOCK Round 2-R0.6 [SPDT/DPDT] 8 8 Square Square 8 8 8 8 [SPDT/DPDT] 8 8 2 o2 Mounting Bracket Mounting Bracket 6.95 1.95 6.95 1.95 1.95 6.956.95 1.95 Solder/Tab Terminal Solder/Tab Terminal 2 o2 [3PDT] [3PDT] 17.8 [SPDT/DPDT] [SPDT/DPDT] 11.1 23 11.1 [3PDT] 23 [3PDT] 2.8W x 0.5t 1 Rectangular 22 6 6 22 1 1 6 1 Rectangular 22 2 6 20.8 20.8 18.8 18.8 11.9 11.9 17.8 17.8 15.8 15.8 17.8 2.8W x 0.5t 0.8W x 0.5t 5 5 5 5 LOCK LOCK 22 0.8W x 0.5t LOCK LOCK 2 5.52 5.5 [PC Board Terminal] 7 27.9 7 [PC Board Terminal] 18.1 2 27.9 18.1 28 28 [Solder/Tab Terminal] [Solder/Tab Terminal] Terminal Arrangement (Bottom View) SPDT/DPDT Contacts TOP TOP TOP 22 22 12 12 32 2232 1222 12 24 24 14 14 34 2434 1424 14 21 21 11 11 31 2131 1121 11 (SPDT contacts the right (SPDTon contacts ononly) the right only) 32 3PDT Contacts TOP 800.262.4332 www.IDEC.com/switches Panel Thickness: 0.5 to 3.2 mm Gasket 1 Locking Ring 1.2 3.85 2.6 Lever Switches 6.95 1.95 8 8 8 6.95 6 1.95 8 8 8 8 1 1 1 6 5 5 6 6 3.85 3.85 6.95 6.95 24 [Solder/Tab Terminal] Locking Ring 3.85 8 8 3.85 3.85 20.9 Gasket 1.95 1.95 3.85 10.8 7 Mounting Bracket Panel Thickness: 0.5 to 3.2 mm 6.95 6.95 6.95 1.95 1 6 1.95 1.95 1 6 8 8 6.95 1.95 2 o2 [SPDT/DPDT] 2 8 17.8 8 8 8 8 8 Mounting Bracket 0.8W x 0.5t Mounting 0.8W xBracket 0.5t 5 8 5 1.95 1.95 15.8 8 17.8 8 o1 [3PDT] 5.5 [3PDT] [3PDT] 7 27.9 4.4 17 2 [Solder/Tab Terminal] 0.8W x 0.5t 17.8 2 5.5 [SPDT/DPDT] [3PDT] 7 2 2 o2 1 o2 6 1 5 6 6 65 11.12 5.523 17.8 17.8 [SPDT/DPDT] [SPDT/DPDT] 2 27.9 7 5.5 4.4 27.9 17 7 4.4 27.9 4.4 17 17 LOCK o2 1 6 15.8 5 5 6 1 1 20.8 5 5 18.8 11.9 17.8 15.8 17.8 23 8 o1 8 o1 [Solder/Tab Terminal] [PC Board Terminal] [Solder/Tab Terminal] 0.8W x 0.5t 0.8W x 0.5t LOCK 0.8W0.8W x 0.5tx 0.5t LOCK 0.8W x 0.5t [PC Board Terminal] LOCK 17.8 20.9 Locking Ring [SPDT/DPDT] LOCK [SPDT/DPDT] LOCK 15.8 7 Mounting Bracket [3PDT] [SPDT/DPDT] [PC BoardLOCK Terminal] [Solder/Tab Terminal] Terminal] Terminal] [Solder/Tab Terminal] [PC Board Terminal][PC Board[Solder/Tab LOCK 18.8 11.9 20.8 18.8 11.9 20.8 Terminal Arrangement (Bottom View) 18.8 11.9 20.8 2.8W x 0.5t [3PDT] 6.95 6.95 [3PDT] 23 Solder/Tab Terminal [3PDT] Solder/Tab Terminal Solder/Tab Terminal 8 2-R0.6 24 [3PDT] [Solder/Tab Terminal] 6 1 6 6 15.8 11.1 8 23 2-R0.6 1.2 1.2 2-R0.6 11.1 3.85 11.1 20.9 Gasket 10.8 Locking Ring 2 20.9 24 10.8 5.5 24 Panel Thickness: 0.5 to 3.2 mmPanel Thickness: 0.5 [SPDT/DPDT] to 3.2 mm Gasket Gasket Locking Ring 11.9 20.8 2.6 3.85 18.8 11.9 1 2.6 11.9 18.8 1 1.2 20.8 2.6 20.8 Flush Bezels 1 10.8 7 Panel Thickness: 0.5 to 3.2 mm 2 17.8 5.5 [PC Board Terminal] [3PDT] Solder/Tab Terminal 18.8 LOCK 8 8 1 5 11.9 1.2 [SPDT/DPDT] LOCK 2 5.5 [3PDT] 2 11.1 [SPDT/DPDT] 7 5.5 2-R0.6 [PC Board Terminal] 23 LOCK 17.8 [SPDT/DPDT] [SPDT/DPDT] LOCK 0.8W x 0.5t [3PDT] 2.8W x 0.5t [PC Board Terminal] 0.8W x 0.5t LOCK 0.8W x 0.5t 2.8W x 0.5t 17.8 5 18.8 17.8 8 o1 1.95 1 5 1.95 5 8 8 8 8 1 5 5 20.8 17.8 15.8 17.8 15.8 2.6 0.6 8 1.95 1 6.95 1.95 17.8 8 15.8 [SPDT/DPDT] [SPDT/DPDT] LOCK 1 2.8W x 0.5t Mounting Ring 6 1.2 6.95 1.95 Mounting 0.6 Ring [SPDT/DPDT] 17.8 LOCK Panel Thickness: 0.5 to 3.2 mm Locking Ring Mounting 0.8W x 0.5t 0.6 Ring Solder/Tab Terminal Solder/Tab Terminal 0.6 [3PDT] 2-R0.6 LOCK 2-R0.6 Solder/Tab Terminal 1.95 Locking Ring 3.85 1.2 2-R0.6 Locking Ring Gasket 2.6 3.85 1 8 2.6 2.6 1.2 Mounting PanelRing Thickness: 0.5 to 3.2 mm Panel Thickness:[SPDT/DPDT] 0.5 to 3.2 mm Gasket Gasket 3.85 1 1 2-R0.6 Solder/Tab Terminal Standard Bezels Dimensions (mm) SPDT/DPDT Contacts 11.1 TOP 23 22 [3PDT] 22 12 24 24 14 21 21 11 3PDT Contacts 11.1 11.1 TOP 23 TOP 23 12 TOP 32 22 32 12 22 12 14 34 24 34 14 24 14 11 31 21 31 11 21 11 [3PDT] [3PDT] (SPDT contacts on the right only) (SPDT contacts on the right only) 33 Dimensions (mm) Buzzers Standard Bezels IP54 Gasket Panel Thickness: 0.5 to 3.2 mm Locking Ring 2.6 1 1.2 2-R0.6 * Solder/Tab Terminal Mounting Ring LOCK 0.8W x 0.5t 17.8 3 3 2.8W x 0.5t 3 3 15.8 17.8 0.6 17.8 * 2 8.8 5.5 7 [PC Board Terminal] IP40 Gasket 20.9 23.8 9 [Solder/Tab Terminal] Terminal Arrangement (Bottom View) Panel Thickness: 0.5 to 3.2 mm Locking Ring Flush & Standard IP54 TOP Buzzer terminal (+) X1 Buzzer terminal (-) Mounting Ring 0.6 IP40 TOP Buzzer terminal (+) 17.8 Buzzer terminal (-) .2 o1 14.6 9 23.8 Flush Bezels 2.6 1 1.2 2-R0.6 Round * Solder/Tab Terminal 2.8W x 0.5t Rectangular 3 3 0.8W x 0.5t 3 3 22 15.8 17.8 o22 Mounting Bracket LOCK 17.8 2 5.5 [PC Board Terminal] 34 Panel Thickness: 0.5 to 3.2 mm Gasket Locking Ring * 7 27.9 [Solder/Tab Terminal] 2 28 X2 X1 X2 Accessories Accessories Item Material Part Number Remarks Metal: Nickel-plated brass MT-001 Used to tighten the locking ring when installing the units on to the panel. Stainless Steel MT-101 Used to remove the lens or button. Locking Ring Wrench o18.0 60.0 Lens Removal Tool 60.0 Switch Guard (180 Spring return) For round / square standard units Spring return For rectangular standard units Switch Guard for Single Board Mounting For rectangular units For Standard Bezels Rubber Boot for Standard Bezels 1 AL-K6SP Guard: Polyacetal Base: Polyarylate AL-KH6SP Guard: Polyacetal Base: Polyarylate 1. For round units LA9Z-K3 Degree of protection: IP65 Used to protect standard pushbuttons and illuminated pushbuttons from inadvertent operation. See 38 for dimensions. With the gasket mounted on the switch, attach the switch guard and mount on the panel. Note: not applicable for flush mounted units. Select operator with built-in switch guard. Degree of protection: IP65 With the gasket mounted on the switch, attach the switch guard and mount on the panel. See 38 for dimensions. LB9Z-D1 2 2. For square units Silicon Rubber LB9Z-D2 Degree of protection: IP65 See 37 for dimensions. See 42 for mounting. 3 3. For rectangular units LB9Z-D3 Mounting Hole Plug Plug: Metal (Zinc diecast) Metal Locking nut: Polyacetal AL-BM6 Degree of protection: IP65 Tightening torque: 0.1 to 0.29 N*m See 37 for dimensions. AL-B6 Degree of protection: IP65 See 37 for dimensions. Gasket: Nitrile rubber Mounting Hole Plug Rubber Nitrile rubber (black) Accessories con't on next page. 35 Accessories Item Material Rubber Boot for Flush Bezels 1 2 Part Number 1. For round units Remarks LB9Z-D6 2. For square units Silicon Rubber LB9Z-D7 Degree of protection: IP65 See 37 for dimensions. See 42 for mounting. For Flush Bezels 3 3. For rectangular units LB9Z-D8 1. F or round units LB9Z-BS6 Mounting Hole Plug 1 Plug: Polyamide (Black) 2 2. For square units Gasket: Nitrile rubber LB9Z-BS7 Mounting Plate: Stainless Steel Degree of protection: IP65 Panel thickness: 0.5 to 3.2 mm See 37 for dimensions. 3 Terminal Cover 1 2 3. For rectangular units LB9Z-BS8 1. F or SPDT/DPDT contacts LB9Z-VL2 See 38 for dimensions. 2. F or 3PDT contacts LB9Z-VL3 800.262.4332 www.IDEC.com/switches 36 Accessories Accessory Dimensions (mm) Rubber Boot Standard Bezel For round units (LB9Z-D1) For square units (LB9Z-D2) For rectangular units (LB9Z-D3) 26 11.5 11.5 11.5 20 o2 0 20 Flush Bezel For round units (LB9Z-D6) For square units (LB9Z-D7) For rectangular units (LB9Z-D8) 24 30 24 4 4 4 24 o Mounting Hole Plug Standard Bezels +0 0 .2 2 12 o1 o1 6. 2 2.5 6. 6 o17.8 o18 o16.5 2 AL-BM6 +0 0 .2 AL-B6 Mounting Hole Layout Gasket Locking Ring Panel Thickness: 0.5 to 6 mm Mounting Hole Layout Flush Bezels F or round units (LB9Z-BS6) F or square units (LB9Z-BS7) Panel Thickness: 0.5 to 3.2 mm Gasket Mounting Plate Locking Ring F or rectangular units (LB9Z-BS8) 2 22 22 o2 18.1 28 .2 18 o 18.2 +0.2 0 Mounting Hole Layout +0.2 0 24.2 +0.2 0 Mounting Hole Layout .2 +00 18.2 Mounting Hole Layout 2 37 Accessories Accessory Dimensions (mm) con't Terminal Cover Standard Bezel For SPDT/DPDT contacts (LB9Z-VL2) 29.9 For 3PDT contacts (LB9Z-VL3) 29.9 TOP 19.6 12.5 2.2 4.4 12.5 20.6 17.6 TOP 24.8 Switch Guard for Standard Bezel Models For round / square units (AL-K6SP) 34 For rectangular units (AL-KH6SP ) 24.0 18.0 [For round / square units] 33 13.0 23.5 11.0 13.0 23.5 11.0 22 R Panel Thickness 0.5 to 2.0 [For rectangular units] 14 For Single Board Mounting (LA9Z-K3) 32.6 Panel Thickness 0.5 to 3.2 R Note: The panel depth is the same for switches with or without switch guards. Both models can be installed on the same PC board. 11 13 23.5 33 22 24 12.4 Wave Key 22 Key No. 8.8 0 22 Logo Side 14 Key No. Side Key No. Side 8.1 Logo Side 7 1.8 Key No. 0 H 22 o3. 0 H Reversible Wave Key 18 14 8.8 Standard Key Non-reversible Wave Key 8.8 22 38 6.3 Key No. Side 14 6.3 www.IDEC.com/switches 22 Logo Side Logo Side 3 H 800.262.4332 8.8 3 H 14 Key No. Key No. Side Key No. Replacement Parts Replacement Parts Item Lens Button Marking Plate Material Part Number Remarks For round units Polyarylate o15.4 H4mm AL6M-Lk For square units Polyarylate 15.4, H4mm AL6Q-Lk Specify the color code in place of k in the part number. A: Amber, C: Clear, G: Green, R: Red, S: Blue, Y: Yellow For rectangular units Polyarylate W21.4 x H4 x D15.4mm AL6H-Lk Note: Use a clear lens for or white (PW) illumination. For round units Polyarylate 15.4, H4mm AB6M-Bk For square units Polyarylate 15.4, H4mm AB6Q-Bk For rectangular units Polyarylate W21.4 x H4 x D15.4 AB6H-Bk For round units Acrylic o13.7 H0.8 AL6M-k For square units Acrylic 13.7, H0.8mm AL6Q-k For rectangular units Acrylic W19.7 x H0.8 (0.4) x D13.7mm AL6H-k For all units Polyamide o17.9, H3.9mm LB9Z-LNP For standard bezel Metal (Stainless steel) 17.9, t0.6mm LB9Z-LP1 For flush bezel Metal (Stainless steel) W21 x H8.2 x D20.6 t0.8mm LB9Z-LP6 For key selector switches Nickel-plated Brass AS6-SK See 38 for dimensions. LA9Z-SK-n Specify Wave key number in place of n in the part number. 0H: Standard wave key (reversible) 1H to 2H: Reversible wave key 3H to 6H: Non-reversible wave key See 38 for dimensions. Specify the color code in place of k in the part number. B: Black, G: Green, R: Red, S: Blue W: White, Y: Yellow Specify the color code in place of k in the part number. B: Black, W: White See 41 for dimensions and engraving area. Locking Ring Anti-rotation Ring Anti-rotation Ring Spare Standard Key Spare Wave key Non-reversible Wave Key Reversible Wave Key For Wave key selector switches Diecast zinc alloy (nickel plated) W14 x H2 x D30.8mm LB Series Replacement LED Unit Item LED Unit Rated Operating Voltage Part Number DC5V LB9Z-LED5k AC/DC12V LB9Z-LED1k AC/DC24V LB9Z-LED2k kColor Code A G PW R S 1. Specify color code in place of the k in the part number. R: Red, G: Green, A: Amber, S: Blue, PW: White 2. All illuminated LB series contain an LED unit. 3. Use a white (PW) LED unit for yellow (Y) illumination. 39 Precautions & Instructions Safety Precautions * Turn off the power to the LB series control units before installation, removal, wiring, maintenance, and inspection. Failure to turn power off may cause electrical shocks or fire hazard. * To avoid burning your hand, use the lamp holder tool when replacing the lamps. * For wiring, use wires of a proper size to meet voltage and current requirements. Solder correctly according to the instructions in "Wiring" and "Notes on Terminal Cover." Improper soldering may cause overheating and create a fire hazard. Also, when using tab terminals, use receptacles of appropriate size. Instructions Wiring Removing and Installing the Contact Block 1. Solder the terminals at 350C within 3 seconds using a 60W soldering iron. Sn-Ag-Cu type is recommended. When soldering, do not touch the LB series with the soldering iron. Also ensure that no tensile force is applied to the terminals. Do not bend the terminal or apply excessive force to the terminal. 2. Use non-corrosive liquid flux. 1. Turn the locking lever on the contact block in the direction opposite to the arrow on the housing. Then the contact block can be removed. 2. Insert the contact block with the TOP markings on the contact block and the operator placed in the same direction. Then lock the units, turning the locking lever in the direction of the arrow. Terminal Cover Solder/tab terminal Insert the terminal cover into the contact block with the TOP markings on the contact block and the terminal cover in the same direction. Note: W hen wiring, insert the lead wires into the terminal cover holes before soldering. After wiring, terminal covers cannot be installed. Standard Bezel locking lever Panel Mounting Remove the contact block from the operator. Insert the operator into the panel cut-out from the front, then install the contact block to the operator. Standard Bezel Flush Bezel Panel Anti-rotation Ring TOP Locking Ring Operating Environment * Do not use the LB series where corrosive gases exist or under an environment exceeding the operating temperature and humidity ranges. Otherwise, damages due to contact failure or change of surface color may occur. * Major parts of the switch are plastic. Scratches or damages may occur when scraped with a sharp object or applied with excessive load or shock. Note that this may cause operation and appearance failure of the operator and bezel. * Adherence of detergent, cutting oil, or special chemicals to the switch may result in operation failures and appearance failures such as change of surface color. Handling Contacts (micro switch) When using NC (normally closed) and NO (normally open) contacts of the same microswitch, avoid connections of different voltages, or connections of different types of power supplies. Failure to observe this instruction may cause a short-circuit. TOP Contact Block Flush Bezel Panel Anti-rotation Ring TOP Locking Ring TOP Contact Block Notes on Mounting Use the optional ring wrench (MT-001) to mount the operator onto the panel. Tightening torque should not exceed 0.7 N*m. Do not use pliers. Excessive tightening will damage the locking ring. 40 Instructions Replacing the Lens Standard Bezel Lens Unit and Contact Block Installation From the opposite side of the TOP marking, remove the operator (lens, marking plate, and lens holder) using the optional lens removal tool (MT-101) by gripping the recesses of the color lens. Removing from the TOP side may damage the metallic bezel. To insert the lens unit into the operator, press in the lens unit by making sure that the latch on the operator is aligned with the latch on the lens unit. Round lens unit Square lens unit Latch Latch Round lens unit Square lens unit Latch Standard Bezel TOP TOP Latch TOP Latch Latch TOP Latch Latch Recess Round Lens Unit Square Lens Unit Operator Recess Latch Latch Operator Removing the Operator (standard bezel) Flush Bezel Flush Bezel TOP From the opposite side of the TOP marking, push the tip of the flat screwdriver to the groove of the color lens and pull out the operator (lens, marking plate, lens holder). Removing from the TOP side may damage the metallic bezel. TOP Latch Latch Recess Operator Marking Plates and Films Removing the Operator (flush bezel) Marking Plate and Marking Film Size Note: A transparent film inside the lens holder is attached to the unit to make it waterproof and cannot be removed. 2. Insert a marking plate into the color lens, and press the lens onto the lens holder to engage the latches. Pay attention to the orientation of the marking plate. Engage Latches 12.0 o13.7 Lens Holder 800.262.4332 www.IDEC.com/switches Engraving Area 18.0 19.7x13.7 13.7 13.6 o13.6 * Engraving must be made on the engraving area within 0.5 mm deep. * The marking plate is made of white acrylic resin. 11.8 19.6 o13.6 * Film thickness: 0.1 mm per film * Marking film is not included. * Recommended marking film: Polyester film Marking Plate and Film Insertion Order Engraved Surface Engraving Surface Marking Color Lens Plate 12.0 12.0 Engraving Area 0.8 Engraving Area Rectangular 0.8 Square o12.0 Round 0.8 Lens Built-in Marking Plate 1. Remove the marking plate by pushing the lens from the rear to disengage the latches between the lens and holder, using the screwdriver as shown below. Applicable Marking Film Replacing the Marking Plate Recesses For illuminated pushbuttons and pushbuttons with illuminated lens, legends and symbols can be engraved on the marking plates, or printed film can be inserted under the lens for labelling purposes. Marking Lens Lens Film Plate Holder TOP Operator The marking plate must be engraved on thespecified side as shown above. Pay attention to the orientation of the marking plate. 41 Instructions Installing Rubber Boots Replacing the LED Unit The LED unit can be replaced by pulling the lens unit out of the contact block. When using the switches in enviroments subject to splashing water or an excessive amount of dust, make sure to use an optional rubber boot. As shown in the drawing below, j remove the gasket from the operator, and k attach the rubber boot from the front (button side). Standard Bezels Contact Block For rectangular and square units, pull out the seals of the rubber boot and place them around the operator sleeve as shown below. Make sure that the seals are not twisted or tucked inside and that the gasket is removed, otherwise waterproof and dustproof characteristics are not ensured. LED Unit Orientation of the LED unit Insert the LED unit into the contact block with the TOP markings on the contact block and LED unit in the same orientation. Rectangular Seals Mount Seals TOP TOP How to Install the Rubber Boot Operator Remove Rubber boot installed Notes on replacing the LED Unit * When replacing the LED unit, make sure that static electricity is not applied. * Make sure that the LB series has cooled down before replacing the LED unit. * To avoid getting burned, be careful not to touch the unit while it is still hot. Gasket Square Seals Seals Mount Operator Notes on Using Quick Connect Terminals Remove 1. 1) Use #110 tab quick connects, 0.5 mm-thick. 2. 2) When connecting the terminals on the left and center, make sure that surfaces of the quick connects face each other. Otherwise, a short-circuit may occur. TOP Rubber boot installed Gasket TOP Round Mount Operator Remove Rubber boot installed Gasket Correct Incorrect 3. 3) Apply only horizontal force against the panel to the tab. The switch may be damaged if a force other than a horizontal force is applied. 800.262.4332 www.IDEC.com/switches 42 Instructions Flush Bezels Maintained Pushbuttons Mount the rubber boot so that the protrusion at the bottom surface of the operator fits with the recess on the operator, placing the rubber boot all around the operator sleeve. Make sure that the protrusion on the rubber boot and the recess on the operator fits correctly, otherwise, the waterproof and dustproof characteristics are not ensured. Do not replace the buttons when the pushbutton is in the maintained position. Replacing the button in the maintained position may damage the internal mechanism. Also, do not remove the contact block with the button in the maintained position. The contact may not operate properly when the contact block is remounted. How to Install the Rubber Boot Correct Good Example Example Protrusion Pushbuttons and Illuminated Pushbuttons with Switch Guard Do not apply force to the switch guard when the switch guard is not attached to a panel. When opening the switch guard, do not open more than 180. The hinge may break. Selector Switches When turning the operator or key, make sure that they are turned to the correct position. Recess Selector Switches with Key Remove Bad Incorrect Example Example Mount Gasket Note: Install the rubber boot before mounting the unit to the panel. Observe the following instructions to prevent malfunction or damage. * Do not remove the key from any key retained position. * In addition to the standard key (key number 0H), six other key numbers are available. Use a key of the matching number with the key cylinder. The standard key does not have a key number indication. * Keys are available in two types. Key numbers 0H (standard), 1H, and 2H are reversible keys which can be inserted in two ways. Key numbers 3H, 4H, 5H, and 6H are non-reversible keys. Make sure of correct insertion direction. 43 Single Board Mounting Flush Bezels The IDEC's LB series is available for single board mounting. o6 drilled hole for operating the locking lever SPDT/DPDT Contacts 3PDT Contacts * 45 mm minimum for switches with guard o1 8. 2 0 * 45 mm minimum for switches with guard o1 8. 2 LB6/LB6M 0. 1 22 min 22 min .1 Rear Installing and Removing Contact Blocks LB7/LB7M 18.2 0.1 Drill mounting holes in the panel as shown below. When the units are mounted collectively, provide adequate clearance. LB8/LB8M or o18 le ss 1.9 +_ 0.05 24.2 0.1 22 min 17.10.05 .2 0.1 1.9 0.05 Standard Bezels (LB1/LB2/LB3/LB4) SPDT/DPDT Contacts 6. 3PDT Contacts 28 min o1 0 +0. 24.2 0.1 28 min All dimensions in mm. .1 +0 0 0 6. 18 or more 0 1 21 or more o1 18.2 0.1 .5 23.2 min 22 min R0 18.2 0.1 +0.1 0 14.8 +_ 0.05 o16.0 22 min Flush Bezels 4- 18.2 0.1 22 min Mounting Holes and Assembly Procedure Panel Cut-out Standard Bezels 23.2 min 22 min 22 min Turn the locking lever to install and remove contact blocks on a PC board using a screwdriver from a hole in the PC board. Determine the location of the switches so that the locking lever can be operated. 18 or more 23.2 or more (24 or more for rectangular units) (24 or more for rectangular units) Assembly Procedure 1. Install the operator to the panel. 2. Mount the contact block to the operator from the back of the panel. 3. Turn the locking lever to lock the contact block. 4. Insert a PC board and solder. Notes: 1. Make sure that each terminal is inserted into the PC board correctly. 2. Do not apply tensile force to the connector cable for an extended period of time. 3. Do not expose the contact block to water. 4. Ensure to lock contact blocks when the contact blocks are installed on the operators. Think Automation and beyond... www.IDEC.com/switches www.IDEC.com USA Japan Germany China/Beijing China/Shenzhen IDEC Corporation Tel: (408) 747-0550 opencontact@IDEC.com IDEC Corporation Tel: +81-6-6398-2571 marketing@IDEC.co.jp IDEC Elektrotechnik GmbH Tel: +49-40-253054-0 service@IDEC.de IDEC (Beijing) Corporation Tel: +86-10-6581-6131 IDEC (Shenzhen) Corporation Tel: +86-755-8356-2977 China/Shanghai Singapore Canada United Kingdom Hong Kong IDEC Canada Ltd. Tel: (905) 890-8561 sales@ca.IDEC.com IDEC Electronics Ltd. Tel: +44-1256-321000 sales@uk.IDEC.com IDEC (H.K.) Co., Ltd. Tel: +852-2803-8989 info@hk.IDEC.com IDEC (Shanghai) Corporation Tel: +86-21-6135-1515 idec@cn.IDEC.com IDEC Asia Pte. Ltd. Tel: +65-6746-1155 info@sg.IDEC.com Australia IDEC Australia Pty. Ltd. Tel: +61-3-8523-5900 sales@au.IDEC.com Taiwan IDEC Taiwan Corporation Tel: +886-2-2698-3929 service@tw.IDEC.com (c)2013 IDEC Corporation. All Rights Reserved. LB9Y-B100-0 02/13 5K Specifications and other descriptions in this catalog are subject to change without notice.