It's SVQP series that is vastly improved heat proof by
Conductive polymer. Please use SVQP series in surface
mounting devices of the switching power supply. It
guarantees the rated ripple current at 105°C, and it's not
necessary to apply temperature derating provided in
other series.
SVP
Series
Vertical Surface Mounting Capacitors
φD±0.5
4.0
5.0
6.3
8.0
10.0
8.0
10.0
Lmax.
5.5
6.0
6.0
7.0
8.0
12.0
12.7
W±0.2
4.3
5.3
6.6
8.3
10.3
8.3
10.3
H±0.2
4.3
5.3
6.6
8.3
10.3
8.3
10.3
C±0.2
5.0
6.0
7.3
9.0
11.0
9.0
11.0
R
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.8 to 1.1
0.8 to 1.1
P±0.2
1.0
1.4
2.1
3.2
4.6
3.2
4.6
Size Code
A5
B6
C6
E7
F8
E12
F12
(unit : mm)
20
Dimensions
2.5
(3.3) 4
(5.2) 6.3
(8.2) 10
(11.5) 16
(18.4) 20
(23) 25
(25)
E12
F12
A5
B6
B6
C6, E7
E7
E12
F8
F12
A5
B6
C6
C6
E7, F8
F8
F8, E12
F12
A5
A5
A5
A5
B6
C6
C6
E7
E7, F8
F8
F8, E12
F12
A5
B6
B6
C6
E7
E7
F8
F8
F8, E12
F12
B6
C6
C6
E7
E7
F8
F8
E12
F12
C6
E7
F8
E12
F12
WV
(SV)
µF
3.3
4.7
6.8
10
15
22
27
33
39
47
56
68
82
100
120
150
180
220
270
330
470
560
680
820
1200
1500
Specifications
Conductive polymer type
Marking : Polarity( ), Rated voltage, Lot.No.
(Purple) SVP(Upper E7), Rated capacitance.
Size List WV : Rated voltage (SV) : Surge (room temperature)
※1 In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or 20V for 25V products
for 120 minutes at 105°C .
※2 Refer to Page 44 for soldering recommendation.
Items Characteristics
1. Category temperature range
2.
Tolerance on rated capacitance (120Hz)
3.
Tangent of loss angle(tanδ)
(120Hz)
4.
Leakage current (µA/2min)(or less)
※1
5. ESR (100k to 300kHz)
-55°C to +105°C
M : ±20%
Less that or equal to the value of Table4
Less that or equal to the value of Table4
Less that or equal to the value of Table4
6.
Characteristics at high temp. and low temp.
Impedance ratio at 100kHz, +20°C
7. Endurance 105°C, 2,000h Rated
voltage applied (25WV→20V)
8. Damp heat (Steady state)
(60°C, 90 to 95%RH, 1,000h no
voltage)
-55°C
+105°C
Z / Z20°C
Z / Z20°C
0.75 to 1.25
0.75 to 1.25
∆C/C
tanδ
ESR
Leakage current
∆C/C
tanδ
ESR
Leakage current
Within ±20%
1.5 or less times of an initial standard
1.5 or less times of an initial standard
Below an initial standard
Within ±20%
1.5 or less times of an initial standard
1.5 or less times of an initial standard
Below the initial standard of an after voltage processing
9.
Solder heat resistance (VPS) ※2
(230°C X 75s)
∆C/C
tanδ
ESR
Leakage current
Within ±10%
1.3 or less times of an initial standard
1.3 or less times of an initial standard
Below the initial standard of an after voltage processing
Specifications for
each series
3. SPECIFICATIONS FOR EACH SERIES