HFD3020 TTL Output Receiver FEATURES * Converts fiber optic input signals to TTL digital outputs * Typical sensitivity 500 nW peak (-33 dBm) * Single 5 V supply requirement * Edge detection circuitry gives 20 dB minimum dynamic range, low Pulse Width Distortion * Operates up to 10 Mbps NRZ * Plastic cap with TO-18 header * Available in metal package (HFD3000) FIBER105.TIF DESCRIPTION The HFD3020 is a sensitive differentiating optical receiver designed for use in short distance, 850 nm fiber optic systems. The receiver uses a hybrid construction consisting of a PIN photodiode, bipolar integrated receiver circuit with internal voltage regulation and external bypass capacitor. The TTL output allows the HFD3020 to be interfaced directly with standard TTL circuits. It is supplied in a Honeywell plastic package, and can be mounted in several fiber optic connectors. Companion optical transmitters are available. OUTLINE DIMENSIONS in inches (mm) APPLICATION Digital HFD3020 fiber optic receivers convert the optical signal in a point to point data communications fiber optic link to a TTL output. The receiver is designed to be mounted in a fiber optic connector that aligns the optical axis of the component to the axis of the optical fiber. Its PIN photodiode is mechanically centered within the TO-18 package. .176 (4.47) .165 (4.19) WINDOW .047 (1.19) DIA. CRUSH RING .229 (5.82) .220 (5.59) .210 (5.33) .081 (2.06) Electrical isolation is important in obtaining the maximum performance of this high sensitivity receiver. A 0.1 F ceramic capacitor must be connected between pin #1 and pin #4. This minimizes external noise on the power leads. Shielding can reduce coupled noise and allow the maximum sensitivity to be obtained. This can include the use of ground planes in the PCB, shielding around the device, and shielding around the leads. The specified maximum operating temperature of 100C allows the HFD3020 to be designed into a broad variety of applications. 262 .500 MIN (12.7) 1 4 3 2 FIBER203.DIM Pinout 1. Capacitor 2. VUU 3. Output (TTL) 4. Case (ground) h Honeywell reserves the right to make changes in order to improve design and supply the best products possible. HFD3020 TTL Output Receiver APPLICATION (continued) Honeywell also offers companion transmitters designed to operate in conjunction with the HFD3020. Note: the final output stage inverts the polarity. When initially powered up, the output state is set to a "1". After setting of the device occurs, incoming edge transitions are recognized and logic switching occurs. OPERATION Optical power (photons) from the fiber strikes the photodiode and is converted to electrical current. This current is then converted into a voltage in the transimpedance preamplifier. The postamplifier is a voltage gain stage with excellent temperature tracking. The edge detection circuit includes an operational amplifier configured as a differentiator, whose output is proportional to the rate of change of the optical signal. A latch retains the most recent edge transition and an inverting buffer drives the TTL output. For example, a light On to light Off transition of the input produces a TTL high output logic level. Because the HFD3020 reacts to transitions in the optical signal rather than DC levels, it shows excellent stability versus temperature and other operating conditions. Also, the device is much less sensitive to the absolute level of the optical signal than DC coupled receivers, allowing for a large range of optical source powers and/or link distances to be directly interfaced. Bandwidth has been limited to minimize noise problems. Reduced pulse width distortion (PWD) is a by-product of the bandwidth limitation. The output of the differentiator has a fixed settling time, assuring good PWD in most applications. Another effect of fixed settling time is the increase of PWD with increased optical power. Very high input optical power may overdrive the differentiator, causing high PWD due to the settling time. The accompanying curves illustrate how PWD increases with increased optical power, increased temperature, and decreased duty cycle. PWD manifests itself as an increase in the width of the TTL low portion of an output waveform, with the TTL high portion decreasing by a like amount. The amount of PWD that a given system can tolerate without an error due to a missing bit of information, is dependant upon system considerations. The output of the HFD3020 will typically connect to the input of some form of a Serial Interface Adaptor IC. The specifications for that IC govern the amount of PWD that can be tolerated in that system. The edge detection circuit monitors the output of the differentiator, and triggers when its output exceeds preset levels. These levels are established to be sufficiently above the worst case RMS noise level to allow excellent bit error rate and are low enough to give high sensitivities which permit operation over long link lengths. This circuitry recognizes the polarity of the change of the optical signal, setting the latch to a "1" when the optical input decreases. Honeywell reserves the right to make changes in order to improve design and supply the best products possible. h 263 HFD3020 TTL Output Receiver ELECTRO-OPTICAL CHARACTERISTICS (TU = 25C, VUU = 5 VDC unless otherwise stated) PARAMETER SYMBOL Minimum Input Sensitivity PUU (peak) High Level Logic Output Voltage Low Level Logic Output Voltage Rise Time Fall Time Supply Current Pulse Width Distortion VIY VIU t t IUU PWD MIN 2.4 TYP MAX UNITS TEST CONDITIONS 0.5 1.0 W aeI = 850 nm into 100/140 m optical fiber, f = 2.5 MHz, Duty Cycle = 50% PUU - 0.1 W, II - 0.8 mA PUU -- 1 W, II - 0.8 mA PUU = 1 W, V = 0.4 to 2.4 V PUU = 1 W, V = 2.4 to 0.4 V PUU -- 1 W, VUU = 5.0 V PUU = 1 W peak PUU = 100 W peak f = 2.5 MHz, Duty Cycle = 50% 3.3 0.4 12 3 15 5 20 20 10 25 V V ns ns mA % ABSOLUTE MAXIMUM RATINGS (25C Free-Air Temperature unless otherwise noted) RECOMMENDED OPERATING CONDITIONS Operating temperature -40 to +85C Storage temperature -40 to +100C Supply voltage +4.5 to +5.5 V Operating temperature -40 to +100C Optical input power 1 to 100 W Lead solder temperature 260C, 10 s Optical signal pulse width > 100 ns Junction temperature 150C Optical signal edges (10 to 90%) < 20 ns Supply voltage +6 V Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. 264 h Honeywell reserves the right to make changes in order to improve design and supply the best products possible. HFD3020 TTL Output Receiver ORDER GUIDE Description Catalog Listing Standard screening, plastic cap package HFD3020-002 This package is also available in special interface receptacles for interfacing to standard fiber optic cables. CAUTION The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product. BLOCK DIAGRAM FIBER INTERFACE Honeywell detectors are designed to interface with multimode fibers with sizes (core/cladding diameters) ranging from 50/125 to 200/230 microns. Honeywell performs final tests using 100/140 micron core fiber. The fiber chosen by the end user will depend upon a number of application issues (distance, link budget, cable attenuation, splice attenuation, and safety margin). The 50/125 and 62.5/125 micron fibers have the advantages of high bandwidth and low cost, making them ideal for higher bandwidth installations. The use of 100/140 and 200/230 micron core fibers results in greater power being coupled by the transmitter, making it easier to splice or connect in bulkhead areas. Optical cables can be purchased from a number of sources. SWITCHING WAVEFORM FIBER030.SCH Fig. 1 Pulse Width Distortion vs Temperature FIBER002.CIR Fig. 2 Pulse Width Distortion vs Frequency FIBER047.GRA Honeywell reserves the right to make changes in order to improve design and supply the best products possible. h FIBER048.GR 265 HFD3020 TTL Output Receiver Fig. 3 Pulse Width Distortion vs Optical Input Power Fig. 4 Propagation Delay vs Optical Input Power FIBER050.GR FIBER049.GRA Fig. 5 Supply Current vs Temperature Fig. 6 Spectral Responsivity FIBER030.GRA 266 h FIBER101.GR Honeywell reserves the right to make changes in order to improve design and supply the best products possible.