PI6C490086 PLL Clock Multiplier Features Description IISupport XTAL or Clock input at 25MHz The PI6C490086 is a low jitter clock generator supporting either XTAL or reference input. Two of its buffered outputs can support wide operating voltage from 1.8V to 3.3V. It is a cost effective way to generate multiple outputs for all kinds of applications that need 25MHz with different power supplies and a 8.192 MHz clock signal. IIThree buffered outputs support VDD operation IIOne 8.192 MHz output IIVery low phase jitter(RMS), 25MHz : < 2ps IIVery low additive jitter: <500fs (typ) II3.3V supply voltage for Core II1.8V ~ 3.3V supply voltage for two outputs IIPackaging: 16-pin TSSOP IICommercial & Industrial Temperature support Applications IINetworking Systems IIFemtocell BTS IIPeripheral Block Diagram Pin Configuration (16-Pin TSSOP) VDD VDDO PLL X1/CLKIN X2 Crystal Oscillator 1 16 X2 VDD 2 15 GND CLK8 GND 3 14 VDD 4 13 CLK3 VDD CLK1 VDDO8 5 12 CLK2 CLK2 CLK8 6 11 VDDO GND 7 10 CLK3 OE# 8 9 GND CLK1 GND 12-0165 X1/ICLKIN VDDO8 16-pin (173 mil) TSSOP OE# 1 www.pericom.com PI6C490086 RevB 2/16/2012 PI6C490086 PLL Clock Multiplier Pin number Pin Name Type Description 1 X1/CLKIN Input Crystal connection or clock input 2, 4, 14 VDD Power 3.3V Core and CLK1 supply voltage 5 VDDO8 Power Supply voltage for CLK8 6 CLK8 Output 8.192 MHz output 7, 9, 15 GND Power Connect to Ground 8 OE# Input Global output enable when low. Internal pull-down resistor. 10 CLK3 Output Clock Output 3 11 VDDO Power Supply voltage from 1.8V to 3.3V for CLK2 and CLK3 12 CLK2 Output Clock Output 2 13 CLK1 Output Clock Output 1 16 X2 Output Crystal connection Function Table OE# CLK1/CLK2/CLK3/CLK8 0 Enabled 1 Hi-Z, weak pull down 12-0165 2 www.pericom.com PI6C490086 RevB 2/16/2012 PI6C490086 PLL Clock Multiplier Maximum Ratings (Above which useful life may be impaired. For user guidelines, not tested.) Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Storage Temperature........................................................... -65C to +150C Supply Voltage to Ground Potential, VDD .........................-0.5V to +4.6V Power Requirements(Over operating free-air temperature range) Symbol Parameter Min. Typ. Max. Units VDD Power Supply Voltage 3.135 3.3 3.465 V VDDO, VDDO8 Power Supply Voltage for outputs 1.71 3.465 V IDD Power supply current, no load TA Ambient Operating Temperature tUP Power Supply Ramp Time 20 mA 0 +70 -40 +85 C 4 ms DC Electrical Characteristics Symbol Parameter Condition Min. VIH Input High Voltage CLKIN, OE# VDD/2+1 VIL Input Low Voltage CLKIN, OE# VOH Output High Voltage VOL Output Low Voltage ZO Nominal Output Impedance R PD Internal Pull-down Resistor CIN Input Capacitance 12-0165 IOH = -4mA and -8mA Typ. Max. V VDD/2-1 V 8MHz output VDDo8 - 0.4 V 25MHz output VDDo - 0.4 V 0.4 IOL = 4mA and 8mA OE# 200 CLKIN 230 Inputs 4 www.pericom.com PI6C490086 V W 20 3 Units kW pF RevB 2/16/2012 PI6C490086 PLL Clock Multiplier AC Electrical Characteristics Symbol Parameter FIN Input Frequency tR (Note 4) Conditions Min. Typ. Max. Units Fundamental Crystal 25 Input Clock 25 Output Rise Time 20% to 80% 25MHz, Note 1 1 tF Output Fall Time 80% to 20% 25MHz, Note 1 1 tR Output Rise Time 20% to 80% 8.192MHz, Note 1 2 tF Output Fall Time 80% to 20% 8.192MHz, Note 1 2 tDC Duty Cycle Note 2 50 Ferror Output Frequency Synthesis Error Jphase Clock Phase Jitter (RMS) 25MHz only, Note 2 0.5 Jadd Additive Jitter 25MHz, Note 3 500 fs Jadd Absolute Period Jitter (pk-pk) 8.192MHz +/-100 ps MHz ns 53 0 % ppm 1.5 ps 1. Note 1: Measured with 7 pF lump load. 2. Note 2: 12 kHz to 20 MHz offset frequency using a crystal input. 3. Note 3: CLKIN input with X2 floating. 4. Note 4: Do not drive this device without a crystal or valid clock input Crystal Oscillator Circuit X1 C1 20pF Crystal(CL=16pF) X2 C2 20pF 0.1F VDD OUTPUTS 0.1F CLOAD VDD GND CLK out GND CMOS Test Configuration 12-0165 4 www.pericom.com PI6C490086 RevB 2/16/2012 PI6C490086 PLL Clock Multiplier Packaging Mechanical: 16-Pin TSSOP (L) DOCUMENT CONTROL NO. PD - 1310 REVISION: E 16 DATE: 03/09/05 .169 .177 1 1 .0256 BSC 0.65 .193 .201 4.9 5.1 4.3 4.5 .004 .008 .047 max. 1.20 .002 .006 .007 .012 0.09 0.20 0.45 .018 0.75 .030 SEATING PLANE .252 BSC 6.4 0.05 0.15 0.19 0.30 Pericom Semiconductor Corporation 3545 N. 1st Street, San Jose, CA 95134 1-800-435-2335 * www.pericom.com Note: 1. Package Outline Exclusive of Mold Flash and Metal Burr 2. Controlling dimentions in millimeters 3. Ref: JEDEC MO-153F/AB DESCRIPTION: 16-Pin, 173-Mil Wide, TSSOP PACKAGE CODE: L Ordering Information Ordering Code Package Code Package Type Operating Temperature PI6C490086LE L Pb-free & Green, 16-pin TSSOP Commercial PI6C490086LIE L Pb-free & Green, 16-pin TSSOP Industrial Notes: * Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ * E = Pb-free and Green * X suffix = Tape/Reel Pericom Semiconductor Corporation * 1-800-435-2336 12-0165 5 www.pericom.com PI6C490086 RevB 2/16/2012