TD62107P/F
2006-02-14
1
TOSHIBA Bipolar Digital Integrated Circuit Silicon Monolithic
TD62107P,TD62107F
4ch High-current Darlington Sink Driver
The TD62107P/F are high-voltage, high-current darlington
drivers and enable inputs which can gate the outputs. All units
feature integral clamp diodes for switching inductive loads.
The TD62107P/F have a wide supply voltage range and all
input are compatible with TTL and 5-V CMOS.
Application include relay, hammer, lamp and stepping moter
drivers.
Please observe the thermal condition for using.
Features
• Output current (single output) 750 mA (max)
• High sustaining voltage output: 45 V min (TD62107P)
35 V min (TD62107F)
• Output clamp diodes
• Enable inputs E1, E2
• Wide supply voltage range VCC = 4.75 to 7 V
• Input compatible with TTL and 5-V CMOS
• GND terminal = heat sink
• Package type-P: DIP-16pin
• Package type-F: HSOP-16pin
Pin Assignm en t (top view)
TD62107P
TD62107F
TD62107P
TD62107F
Weight
DIP16-P-300-2.54A: 1.11 g (typ.)
HSOP16-P-300-1.00: 0.50 g (typ.)
Heat sink
& GND
1 2 3 4 5 6 7
14 13 12 11 10 9
O2 Heat sink
& GND O3 O4 COMVCC
E1 I1 I2 I3 I4
16
2E8
15
O1
Heat sink
& GND
1 2 3 4 5 6 7
14 13 12 11 10 9
NC Heat sink
& GND O4 COM NCVCC
E1 I1 NC I3 NC
16
2E 8
15
O1 O3 O2
I2 I4
TD62107P/F
2006-02-14
2
Schematics (each driver) Truth Table
E1 2E I1 to I4 O1 to O4
L L L or H Disable OFF
L H L or H Disable OFF
H L L or H Enable In
H H L or H Disable O FF
In = I1~I4
Input Equivalent Circuit Output Equivalent Circuit
Note: The input and output parasi t ic diodes cannot be used as clamp diodes.
Absolute Maximum Ratings (Ta = 25°C)
Characteristics Symbol Rating Unit
Supply voltage VCC −0.5 to 17 V
P −0.5 to 45
Outp u t sustainin g
voltage F VCE (SUS ) −0.5 to 35 V
Output current IOUT 750 mA
Input voltage VIN −0.5 to VCC +
0.5 V
P 45
Clamp diode reverse
voltage F VR 35 V
Clamp diode forword current IF 500 mA
P 2.7 (Note 1)
Power dissipation F PD 1.4 (Note 2) W
Operating temperatur e Topr −40 to 85 °C
Storage temperature Tstg −55 to 150 °C
Note 1: On glass epoxy PCB (50 × 50 × 1.6 mm Cu 50%)
Note 2: On glass epoxy PCB (60 × 30 × 1.6 mm Cu 30%)
Common
Output
VCC
Input
I1
I2
I3
I4
O1
O2
O3
O4
Common
E1
2E
TD62107P/F
2006-02-14
3
Recomm end ed Operating Co ndition s (Ta = −40 to 85°C)
Characteristics Symbol Condition Min Typ. Max Unit
Supply voltage VCC ⎯ 4.75 ⎯ 15 V
P 0 ⎯ 45
Output sustaining
voltage F VCE (SUS ) ⎯ 0 ⎯ 35 V
T
pw = 25 ms, Duty = 75%, 1 Circuit 0 ⎯ 500
P Duty = 30% 0 ⎯ 400
Output current
F
IOUT Tpw = 2 5 ms, 4 Circuit Duty = 40% ⎯ ⎯ 300
mA
Input voltage VIN ⎯ 0 ⎯ V
CC V
P ⎯ ⎯ 45
Clamp diode reverse
voltage F VR ⎯ ⎯ ⎯ 35 V
Clamp diode forward current IF ⎯ ⎯ ⎯ 500 mA
P ⎯ ⎯ ⎯ 1.0
Power dissipation F PD Ta = 85°C (Note 1) ⎯ ⎯ 0.7 W
Note1: On Glass Epoxy PCB (60 × 30 × 1.6 m m Cu 30%)
Electrical Characteristics (Ta = 25°C)
Characteristics Symbol
Test
Circuit Test Condit ion Min Typ. Max Unit
High level VIH 2.0 ⎯ V
CC
Input voltage Low level VIL 1 ⎯ ⎯ 0.8 V
P VCE = 45 V, Ta = 75°C ⎯ ⎯ 100
Output current High
level F IOH 2 VCE = 35 V, Ta = 85°C ⎯ ⎯ 100 µA
Output voltage Low level VOL 3 IOUT = 50 mA ⎯ ⎯ 1.3 V
High level IIH 4 VIN = 13 V ⎯ ⎯ 100 µA
Input current Low level IIL 5 VIN = 0.4 V ⎯ ⎯ −0.3 mA
P VR = 45 V ⎯ ⎯ 100
Clamp diode reverse current F IR 6 VR = 35 V ⎯ ⎯ 100 µA
Clamp diode forward voltage VF 7 IF = 500 mA ⎯ ⎯ 2.0 V
Output
high ICCH 4 VCC = 13 V, VIN = 0 V
Output open ⎯ ⎯ 13
Supply current Output
low
ICC ICCL 5 VCC = 13 V, VIN = 5 V
Output open ⎯ ⎯ 17
mA
P VCC = 5 V, RL = 90 Ω
CL = 15 pF, VOUT = 45 V ⎯ 5 ⎯
Turn-on delay
F tON 8 VCC = 5 V, RL = 70 Ω
CL = 15 pF, VOUT = 35 V ⎯ 5 ⎯
µs
P VCC = 5 V, RL = 90 Ω
CL = 15 pF, VOUT = 45 V ⎯ 5 ⎯
Turn-off delay F tOFF 8 VCC = 5 V, RL = 70 Ω
CL = 15 pF, VOUT = 35 V ⎯ 5 ⎯
µs
TD62107P/F
2006-02-14
4
Test Circuit
1. VIH, VIL 2. IOH 3. VOL
4. IIH, ICCL 5. IIL, ICCL 6. IR
7. VF 8. tON, tOFF
Input Condition
Note 1: Pulse width 50 µs, duty cycle 10%
Output Impedance 50 Ω, tr ≤ 5ns, t f ≤ 10 ns
Note 2: VIH = 3 V, E1 = VIH, 2E = GND, VCC = 5 V
Note 3: CL includes probe and jig capacitance
Precauti ons fo r Using
This IC does not include built-in protection circuits for excess current or overvoltage.
If this IC is subjected to excess current or overvoltage, it may be destroyed.
Hence, the utmost care must be taken when systems which incorporate this IC are designed.
Utmost care is necessary in the design of the output line, VCC, COMMON and GND line since IC may be
destroyed due to short-circuit between outputs, air contamination fault, or fault by improper grounding.
Pulse
generator
(Note 1)
Input
CL = 15 pF
(Note 3)
VOUT
Output
RL
Open
V
(Note 2)
VIN (ON) VOL
Open
IOUT
VCC
ICCL
IIH
VIN
Open
Open
VCC
ICCH
IIL
VIN
Open
Open
VCC
Open
Open
IR VR
VCC
Open
Open
IF
VF
VCC
10% 50%
tON t
OFF
tf
trVIH = 3 V
VOH
VOL
Input 50%
50 µs
Output 50% 50%
90%
10%
90%
0
IOH
Open
VCE
VCC
VIH, VIL VCE
Open VCC
IOUT
TD62107P/F
2006-02-14
5
0075 150
4.0
3.0
1.0
2.0
100 25 125 50
TD62107P
VCE (sat) – IOUT
VOUT – VIN
IOUT – Duty cycle
IOUT – Duty cycle
PD – Ta
PD – Ta
Output saturation voltage VCE (sat) (V) Input voltage VIN (V)
Duty cycle (%) Duty cycle (%)
Ambient temperature Ta (°C) Ambient temperature Ta (°C)
Output curre nt IOUT (A)
Output curre nt IOUT (A)
Output current IOUT (A)
Output curre nt IOUT (A)
Power dissipation PD (W)
Power dissipation PD (W)
0
0 75 150
4
3
1
2
100 25 125 50
(1) Type-F on PCB
60 × 30 × 1.6 mm Cu 30%
(2) Type-F free air
(1)
(2)
0
0 1.2 1.6
8.0
6.0
0.2
0.4
0.4 0.8
VCC = 5 to 17 V
Ta = 75°C
−30
25
004.0 5.0
50
20
30
2.0 3.0
−30
25
Ta = 75°C
IOUT = 500 mA
40
10
1.0
0.2
30 90
0.8
0.4
0.6
50 70
Ta = 75°C
Recommended limit
4 Circuit
2
1
3
Absolute maximum ratings
0.2
30 90
0.8
0.4
0.6
50 70
Ta = 25°C
4 Ci rcuit
3
1, 2 Absolute maximum ratings
Recommended limit
TD62107P/F
2006-02-14
6
Package Dimensions
Weight: 1.11 g (typ.)
TD62107P/F
2006-02-14
7
Package Dimensions
Weight: 0.50 g ( typ.)
TD62107P/F
2006-02-14
8
