3001 00520177 - HONEYWELL - Datasheet.Live

www.teledynerelays.com RF100 RF103/1203/Q1

RF & MICROWAVE

SERIES

RF100

RF103

HIGH REPEATABILITY

BROADBAND

CENTIGRID®RELAYS

DPDT

SERIES

DESIGNATION RELAY TYPE

RF100 Repeatable, RF, Centigrid®relay

RF103 Sensitive, repeatable, RF, Centigrid®relay

PERFORMANCE FEATURES

The ultraminiature RF100 and RF103 relays are designed to provide improved

RF signal repeatability over the frequency range. These relays are highly

suitable for use in attenuator and other RF circuits, the RF100 and RF103

feature:

• High repeatability.

• Broader bandwidth.

• Metal enclosure for EMI shielding.

• Ground pin option to improve case grounding.

• High isolation between control and signal paths.

• Highly resistant to ESD.

CONSTRUCTION FEATURES

The following unique construction features and manufacturing techniques

provide excellent resistance to environmental extremes and overall high

reliability.

• Uni-frame motor design provides high magnetic efficiency and mechanical

rigidity.

• Minimum mass components and welded construction provide maximum

resistance to shock and vibration.

• Advanced cleaning techniques provide maximum assurance of internal

cleanliness.

• Gold-plated precious metal alloy contacts ensure reliable switching.

• Hermetically sealed.

• Solderable leads.

INTERNAL CONSTRUCTION

UNI-FRAME

UPPER

STATIONARY

CONTACT

LOWER

STATIONARY

CONTACT

ARMATURE

MOVING CONTACT

ENVIRONMENTAL AND

PHYSICAL SPECIFICATIONS

Temperature

(Ambient)

Storage –65°C to +125°C

Operating –55°C to +85°C

Vibration

(General Note 1) 10 g’s to 500 Hz

Shock

(General Note 1)

30 g’s,

6 msec, half-sine

Enclosure Hermetically sealed

Weight

RF100 0.09 oz. (2.55g) max.

RF103 0.16 oz. (4.5g) max.

www.teledynerelays.com RF100 RF103/1203/Q1

RF & MICROWAVE

RF NOTES

1. Test conditions: a. Fixture: .031" copper clad, reinforced PTFE, RT/duroid®6002 with SMA connectors. (RT/duroid®is a

registered trademark of Rogers Corporation.)

b. Room ambient temperature.

c. Terminals not tested were terminated with 50-ohm load.

d. Contact signal level: –10 dBm.

e. No. of test samples: 2.

2. Data presented herein represents typical characteristics and is not intended for use as specification limits.

3. Data is per pole, except for pole-to-pole data.

4. Data is the average from readings taken on all open contacts.

5. Data is the average from readings taken on poles with coil energized and de-energized.

6. Data is the average from readings taken on all closed contacts.

7. Test fixture effect de-embedded from frequency and time response data.

SERIES RF100 AND RF103

TYPICAL RF CHARACTERISTICS (See RF Notes)

Isolation Across Contacts (RF Note 4)

-60

-50

-40

-30

-20

0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000

Frequency (MHz)

Isolation (dB)

Isolation Pole to Pole (RF Note 5)

-60

-50

-40

-30

-20

0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000

Frequency (MHz)

Isolation (dB)

Insertion Loss (RF Note 6)

-1.8

-1.6

-1.4

-1.2

-1

-0.8

-0.6

-0.4

-0.2

0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000

Frequency (MHz)

Insertion Loss (dB)

VSWR (RF Note 6)

1.00

1.40

1.80

2.20

2.60

3.00

0 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000

Frequency (MHz)

VSWR

RF100 Time Response (RF Note 6)

-0.1

0.1

0.3

0.5

0.7

0.9

1.1

-100 0 100 200 300 400 500 600 700 800 900

Time (ps)

Volt

10%

90%

37ps reference

58.1ps pulse rise time

81.1ps propagation delay time

www.teledynerelays.com RF100 RF103/1203/Q1

RF & MICROWAVE

RF INSERTION LOSS REPEATABILITY NOTES

1. Test conditions: a. Fixture: .031" copper clad, reinforced PTFE, RT/duroid®6002 with SMA connectors. (RT/duroid®is a

registered trademark of Rogers Corporation.)

b. Relay header is in contact with, but not soldered to, ground plane or connected to ground via ground pin.

c. Test performed at room ambient temperature.

d. Contact signal level: 20 dBm.

2. Data presented herein represents typical characteristics and is not intended for use as specification limits.

3. Insertion loss repeatability measured over frequency range from .3 MHz to 4 GHz.

TYPICAL RF INSERTION LOSS REPEATABILITY CHARACTERISTICS (NOTES 1 AND 2)

SERIES RF100 AND RF103

100

0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

Repeatability (dB) Repeatability (dB)

REPEATABILITY CHARACTERISTICS RF100 RELAYS

100

REPEATABILITY CHARACTERISTICS RF103 RELAYS

Normally Open

Normally Closed

% Total Number Recorded Test Cycles% Total Number Recorded Test Cycles

0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20

www.teledynerelays.com RF100 RF103/1203/Q1

RF & MICROWAVE

SERIES RF100 AND RF103

GENERAL ELECTRICAL SPECIFICATIONS (@25°C)

DETAILED ELECTRICAL SPECIFICATIONS (@25°C)

GENERAL NOTES

1. Relays will exhibit no contact chatter in excess of 10 μsec or transfer in excess of 1 μsec.

Contact arrangement DPDT

Rated duty Continuous

Contact resistance .100 ohm max. initial (measured 1/8" from the header)

Contact load rating Low level: 10 to 50 μA, 10 to 50 mV

Contact life rating 10,000,000 cycles typical at low level

Coil operating power RF100: 369–500 mW typical @ nominal rated voltage

RF103: 180–250 mW typical @ nominal rated voltage

Operate time RF100 4.0 ms. max.

RF103 6.0 ms. max.

Release time RF100 3.0 ms. max.

RF103 3.0 ms. max.

Intercontact capacitance 0.4 pF typical

Insulation resistance 1,000 MΩmin. (between mutually isolated terminals)

Dielectric strength 350 VRMS / 60 Hz @ atmospheric pressure

BASE PART NUMBERS RF100-5

RF103-5

RF100-12

RF103-12

Coil voltage, nominal, VDC 5.0 12.0

Coil resistance, ohms ± 20%

RF100 50 390

RF103 100 800

Pick-up voltage max, VDC 3.6 9.0

OUTLINE DIMENSIONS

• TERMINAL NUMBERING AND SCHEMATIC ARE AS VIEWED FROM THE TERMINALS.

• DIMENSIONS ARE IN INCHES (MILLIMETERS).

• SCHEMATIC AND EXTERNAL DIMENSIONS SHOWN WITHOUT GROUND PINS.

• TO ORDER THE CASE GROUND OPTION, AFTER THE SERIES DESIGNATOR, ADD “Y” TO

THE PART NUMBER FOR TAB POSITION OR “Z” TO THE PART NUMBER FOR CENTER

POSITION.

EXAMPLE: RF103Y-COIL VOLTAGE

EXTERNAL DIMENSIONS

TERMINAL NUMBERING SCHEMATIC

.031 (.79)

REF.

.035 (.89)

REF.

78H DIMENSION

RF100

RF103

.290

(7.37)

.395

(10.03)

MAX.

.017

+.002

-.001

()

.43+.05

-.03

.335

(8.51)

SQ. MAX.

.375

(9.53)

SQ. MAX.

.75 (19.05) MIN.

0.100 0.010

(2.54 0.25)

Pad designation and

bottom view dimensions Height For use with the following: Dim. H

Max.

“M4” Pad for TO-5

ER411T

ER412, ER412D, ER412DD .295 (7.49)

712, 712D, 712TN,

RF300, RF310, RF320 .300 (7.62)

ER420, ER422D, ER420DD, 421,

ER421D, ER421DD, ER422, ER422D,

ER422DD, 722, 722D, RF341

.305 (7.75)

ER431T, ER432T,

ER432, ER432D, ER432DD .400 (10.16)

732, 732D, 732TN, RF303, RF313,

RF323 .410 (10.41)

RF312 .350 (8.89)

“M4” Pad for TO-5

ER411, ER411D, ER411DD .295 (7.49)

ER431, ER431D, ER431DD .400 (10.16)

RF311 .300 (7.62)

RF331 .410 (10.41)

“M4” Pad for Centigrid®

172, 172D .305 (7.75)

ER114, ER114D, ER114DD,

J114, J114D, J114DD .300 (7.62)

ER134, ER134D, ER134DD,

J134, J134D, J134DD .400 (10.16)

RF100 .315 (8.00)

RF103 .420 (10.67)

“M9” Pad for Centigrid®

122C, A152 .320 (8.13)

ER116C, J116C .300 (7.62)

ER136C, J136C .400 (10.16)

RF180 .325 (8.25)

A150 .305 (7.75)

Notes:

1. Spacer pad material: Polyester  lm.

2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering

example in the applicable datasheet.

3. Dimensions are in inches (mm).

4. Unless otherwise speci ed, tolerance is ± .010 (.25).

5. Add 10 m to the contact resistance show in the datasheet.

6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.

Ø.150

[3.81]

(REF)

Dim H

MAX

Dim H

MAX

Dim H

MAX

.156

[3.96]

(REF)

.256

[6.5]

(REF)

Dim H

MAX

Appendix A: Spacer Pads

Pad designation and

bottom view dimensions Height For use with the following: Dim. H

Max.

“M” Pad 5/ 6/

ER411T, J411T, ER412, ER412D

ER412DD, J412, J412D, J412DD

ER412T, J412T

.388 (9.86)

712, 712D, 712TN .393 (9.99)

ER431T, J431T, ER432, ER432D

ER432DD, J432, J432D, J432DD

ER432T, J432T

.493 (12.52)

732, 732D, 732TN .503 (12.78)

ER420, J420, ER420D, J420D

ER420DD, J420DD, ER421, J421

ER421D, J421D, ER421DD

J422D, ER422DD, J422DD, 722

.398 (10.11)

“M2” Pad 7/ 8/

ER411T

ER412, ER412D, ER412DD

J412, J412D, J412DD

.441 (11.20)

712, 712D .451 (11.46)

ER421, ER421D, ER421DD

722, 732D .451 (11.46)

ER431T

ER432, ER432D, ER432DD .546 (13.87)

732, 732D .556 (14.12)

“M3” Pad 5/ 6/ 9/

ER411, ER411D, ER411DD

ER411TX

ER412X, ER412DX, ER412DDX

ER412TX

.388 (9.86)

712X, 712DX, 712TNX .393 (9.99)

ER420X, ER420DX, ER420DDX

ER421X, ER421DX, ER421DDX

ER422X, ER422DX

ER422DDX, 722X, 722DDX

.398 (10.11)

ER431, ER431D, ER431DD

ER431TX

ER432X, ER432DX, ER432DDX

ER432TX

.493 (12.52)

732X, 732DX, 732TNX .503 (12.78)

Notes:

1. Spreader pad material: Diallyl Phthalate.

2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example

in the applicable datasheet.

3. Dimensions are in inches (mm).

4. Unless otherwise speci ed, tolerance is ± .010” (0.25).

5/. Add 25 m to the contact resistance shown in the datasheet.

6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.

7/. Add 50 m to the contact resistance shown in the datasheet.

8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.

9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)

.370 [9.4]

MAX SQ

.150

[3.81]

.100

[2.54]

.200

[5.08]

.300

[7.62]

.100

[2.54]

Dim H

MAX

.370

[9.4]

MIN

.014

[0.36]

(REF)

.390 [9.91]

.300

[7.62]

.100

[2.54]

.300

[7.62]

.100

[2.54] .150

[3.81]

.150

[3.81]

.130

[3.3]

Dim H

MAX

.370 [9.4]

MAX SQ

.150

[3.81]

.100

[2.54]

.200

[5.08]

.300

[7.62]

.100

[2.54]

Dim H

MAX

.370

[9.4]

MIN

.014

[0.36]

(REF)

Appendix A: Spreader Pads

.100

[2.54]

.100

[2.54]

.100

[2.54]

"Y" POSITION

"Z" POSITION

.100

[2.54]

.100

[2.54]

.100

[2.54]

"W" POSITION

"U" POSITION

(ER116C and ER136C only)

"X" POSITION

"Z" POSITION

"Y" POSITION

.050

[1.27]

36°±3°

Ø.200

[Ø5.08]

"Z" POSITION

"Y" POSITION

"X" POSITION

45°±3°

"Z" POSITION

"Y" POSITION

Ø.200

[Ø5.08]

Centigrid® Relays:

RF100, RF103, ER114, ER134, 172

Centigrid® Relays:

RF180, ER116C, 122C, ER136C

TO-5 Relays:

ER411T, ER412, ER412T, ER420, ER421, ER422,

ER431T, ER432, ER432T, 712, 712TN, 400H, 400K,

400V, RF300, RF303, RF341, RF312, RF310, RF313,

RF320, RF323

TO-5 Relays:

ER411, ER431, RF311, RF331

NOTES

1. Terminal views shown

2. Dimensions are in inches (mm)

3. Tolerances: ± .010 (±.25) unless otherwise speci ed

4. Ground pin positions are within .015 (0.38) dia. of true position

5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref.

6. Lead dia. 0.017 (0.43) nom.

Indicates ground pin position

Indicates glass insulated lead position

Indicates ground pin or lead position

depending on relay type

Appendix A: Ground Pin Positions