MOTOROLA Order Number: MC100ES6039 Rev 0, 12/2003 SEMICONDUCTOR TECHNICAL DATA Preliminary Information 2.5V/3.3V ECL/PECL/HSTL/LVDS /2/4, /4/6 Clock Generation Chip The MC100ES6039 is a low skew /2/4, /4/6 clock generation chip designed explicitly for low skew clock generation applications. The internal dividers are synchronous to each other, therefore, the common output edges are all precisely aligned. The device can be driven by either a differential or single--ended ECL or, if positive power supplies are used, LVPECL input signals. In addition, by using the VBB output, a sinusoidal source can be AC coupled into the device. The common enable (EN) is synchronous so that the internal dividers will only be enabled/disabled when the internal clock is already in the LOW state. This avoids any chance of generating a runt clock pulse on the internal clock when the device is enabled/disabled as can happen with an asynchronous control. The internal enable flip--flop is clocked on the falling edge of the input clock, therefore, all associated specification limits are referenced to the negative edge of the clock input. MC100ES6039 DW SUFFIX 20 LEAD SOIC PACKAGE CASE 751D ORDERING INFORMATION Device Package MC100ES6039DW SO--20 MC100ES6039DWR2 SO--20 Upon startup, the internal flip--flops will attain a random state; therefore, for systems which utilize multiple ES6039s, the master reset (MR) input must be asserted to ensure synchronization. For systems which only use one ES6039, the MR pin need not be exercised as the internal divider design ensures synchronization between the /2/4 and the /4/6 outputs of a single device. All VCC and VEE pins must be externally connected to power supply to guarantee proper operation. The 100ES Series contains temperature compensation. Features * Maximum Frequency >1.0 GHz Typical * 50 ps Output--to--Output Skew * PECL Mode Operating Range: VCC = 2.375 V to 3.8 V with VEE = 0 V * ECL Mode Operating Range: VCC = 0 V with VEE = --2.375 V to --3.8 V * * * * Open Input Default State Synchronous Enable/Disable Master Reset for Synchronization of Multiple Chips VBB Output * LVDS and HSTL Input Compatible This document contains information on a product under development. Motorola reserves the right to change or discontinue this product without notice. (c) Motorola, Inc. 2003 1 MC100ES6039 Q1 Q1 Q2 Q2 Q3 Q3 VEE 20 19 18 17 16 15 14 13 12 11 1 2 VCC EN 3 4 CLK 5 6 CLK VBB PIN DESCRIPTION PIN FUNCTION CLK*, CLK* ECL Diff Clock Inputs EN* ECL Sync Enable MR* ECL Master Reset ECL Reference Output 7 8 9 10 VBB MR VCC DIVSELa Q0 NC Q0 DIVSELb VCC Q0, Q1, Q0, Q1 ECL Diff /2/4 Outputs Q2, Q3, Q2, Q3 ECL Diff /4/6 Outputs Warning: All VCC and VEE pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. 20--Lead Pinout (Top View) DIVSELa* ECL Freq. Select Input /2/4 DIVSELb* ECL Freq. Select Input /4/6 VCC ECL Positive Supply VEE ECL Negative Supply NC No Connect * Pins will default low when left open. DIVSELa Q0 CLK /2/4 R CLK Q0 Q1 Q1 Q2 EN /4/6 R MR DIVSELb Q2 Q3 Q3 VEE Figure 2. Logic Diagram FUNCTION TABLES CLK EN MR Z ZZ X L H X L L H FUNCTION Divide Hold Q0:3 Reset Q0:3 X = Don't Care Z = Low--to--High Transition ZZ = High--to--Low Transition DIVSELa L H DIVSELb L H MOTOROLA Q0:1 OUTPUTS Divide by 2 Divide by 4 Q2:3 OUTPUTS Divide by 4 Divide by 6 2 TIMING SOLUTIONS MC100ES6039 CLK Q (/2) Q (/4) Q (/6) Figure 3. Timing Diagram CLK tRR RESET Q (/n) Figure 4. Timing Diagram Table 1. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 k Internal Input Pullup Resistor 75 k ESD Protection Human Body Model Machine Model Charged Device Model > 2 kV > 100 V > 2 kV Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test TIMING SOLUTIONS 3 MOTOROLA MC100ES6039 Table 2. MAXIMUM RATINGSa Symbol Parameter Condition 1 Condition 2 Rating Units 4.6 V --4.6 V 4.6 --4.6 V V 50 100 mA mA 0.5 mA --40 to +85 C VCC PECL Mode Power Supply VEE = 0 V VEE ECL Mode Power Supply VCC = 0 V VI PECL Mode Input p Voltage g ECL Mode Input Voltage VEE = 0 V VCC = 0 V Iout Output Current Continuous Surge IBB VBB Sink/Source TA Operating Temperature Range Tstg Storage Temperature Range --65 to +150 C JA Thermal Resistance (Junction--to--Ambient) VI VCC VI VEE 0 LFPM 500 LFPM 20 TSSOP 20 TSSOP TBD TBD C/W C/W 0 LFPM 500 LFPM 20 SOIC 20 SOIC TBD TBD C/W C/W a Maximum Ratings are those values beyond which device damage may occur. Table 3. DC CHARACTERISTICS, PECL (VCC = 2.5 V5%, VEE = 0 V) - 40C Symbol IEE Characteristic Min Power Supply Current Typ 0C to 85C Max Min 35 Typ Max 35 Unit mA VOH Output HIGH Voltagea 1415 1495 1620 1475 1545 1620 mV VOL Output LOW Voltagea 670 805 945 690 795 880 mV VIH Input HIGH Voltage (Single--Ended) 1335 1620 1335 1620 mV VIL Input LOW Voltage (Single--Ended) 690 1025 690 1025 mV 1240 1120 1240 mV VBB Output Reference Voltage 1120 VPP Differential Input Voltageb 0.12 1.3 0.12 1.3 V VCMR Differential Cross Point Voltagec 1.0 VCC--0.8 1.0 VCC--0.8 V 150 A IIH Input HIGH Current IIL Input LOW Current 150 0.5 0.5 A NOTE: ES6014 circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. a Output termination voltage VTT = 0V for VCC = 2.5V operation is supported but the power consumption of the device will increase. b VPP (DC) is the minimum differential input voltage swing required to maintain device functionality. c VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR (DC) range and the input swing lies within the VPP (DC) specification. MOTOROLA 4 TIMING SOLUTIONS MC100ES6039 Table 4. DC CHARACTERISTICS, PECL (VCC = 3.3 V5%, VEE = 0 V) - 40C Symbol Characteristic Min Typ 0C to 85C Max Min Typ Power Supply Current VOH Output HIGH Voltagea 2215 2295 2420 2275 2345 2420 mV VOL Output LOW Voltagea 1470 1605 1745 1490 1595 1680 mV VIH Input HIGH Voltage (Single--Ended) 2135 2420 2135 2420 mV VIL Input LOW Voltage (Single--Ended) 1490 1825 1490 1825 mV VBB Output Reference Voltage 1920 2040 1920 2040 mV VPP Differential Input Voltageb 0.12 1.3 0.12 1.3 V 1.0 VCC--0.8 1.0 VCC--0.8 V 150 mA Differential Cross Point IIH Input HIGH Current IIL Input LOW Current Voltagec 33 Unit IEE VCMR 33 Max mA 150 0.5 0.5 mA NOTE: MC100ES6039 circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. a All loading with 50 to VCC--2.0 volts. b VPP (DC) is the minimum differential input voltage swing required to maintain device functionality. c VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR (DC) range and the input swing lies within the VPP (DC) specification. Table 5. DC CHARACTERISTICS, ECL (VCC = 0 V, VEE = --3.3 V5%) - 40C Symbol IEE Characteristic Min Power Supply Current Typ 0C to 85C Max Min 33 Typ Max 33 Unit mA VOH Output HIGH Voltagea --1085 --1005 --880 --1025 --955 --880 mV VOL Output LOW Voltagea --1830 --1695 --1555 --1810 --1705 --1620 mV VIH Input HIGH Voltage (Single--Ended) --1165 --880 --1165 --880 mV VIL Input LOW Voltage (Single--Ended) --1810 --1475 --1810 --1475 mV VBB Output Reference Voltage --1380 --1260 --1380 --1260 mV VPP Differential Input Voltageb 0.12 1.3 0.12 1.3 V VEE+0.5 --0.3 VEE+0.5 --0.3 V 150 mA VCMR Differential Cross Point IIH Input HIGH Current IIL Input LOW Current Voltagec 150 0.5 0.5 mA NOTE: MC100ES6039 circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. a All loading with 50 to VCC--2.0 volts. b VPP (DC) is the minimum differential input voltage swing required to maintain device functionality. c VCMR (DC) is the crosspoint of the differential input signal. Functional operation is obtained when the crosspoint is within the VCMR (DC) range and the input swing lies within the VPP (DC) specification. TIMING SOLUTIONS 5 MOTOROLA MC100ES6039 Table 6. DC CHARACTERISTICS, HSTL (VCC = 2.375 V to 3.8 V, VEE = 0 V) - 40C Symbol Characteristic VIH Input HIGH Voltage (Single Ended) VIL Input LOW Voltage (Single Ended) Min Typ 0C to 85C Max Min 1200 Typ Max 1200 Unit mV 400 400 mV Max Unit Table 7. AC CHARACTERISTICS (VCC = 0 V; VEE = --3.0 V or VCC = 3.0 V; VEE = 0 V)a - 40C Symbol Characteristic Min fmax Maximum Frequency tPLH, tPHL Propagation Delay tRR Reset Recovery ts Setup Time EN, CLK DIVSEL, CLK th Hold Time CLK, EN CLK, DIVSEL tPW Minimum Pulse Width tSKEW Within Device Skew Device--to--Device Skewb tJITTER Cycle--to--Cycle Jitter Typ Max Min >1 CLK, Q (Diff) MR, Q MR 550 700 700 800 200 200 400 100 200 120 180 200 400 100 200 50 140 550 450 Q, Q 800 900 50 200 Input Voltage Swing (Differential) 150 0.2 VEE+0.2 Q, Q Max Min >1 100 200 100 ps 120 180 200 400 120 180 ps 100 200 50 140 100 200 50 140 ps 550 450 550 450 50 200 900 1000 GH z 825 950 100 300 100 300 50 200 <2 800 Typ 675 800 <2 Differential Cross Point Voltage PECL ECL 85C >1 750 850 VPP Output Rise/Fall Times (20% -- 80%) Typ 600 700 VCMR tr tf 25C 1200 150 VCC--1.1 --1.1 0.2 VEE+0.2 250 125 800 975 1100 ps 100 300 <2 1200 150 VCC--1.1 --1.1 0.2 VEE+0.2 275 150 800 ps ps ps 1200 mV V 110 180 190 VCC--1.1 --1.1 215 300 ps a Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 to VCC--2.0 V. b Skew is measured between outputs under identical transitions. Duty cycle skew is defined only for differential operation when the delays are measured from the cross point of the inputs to the cross point of the outputs. Q D Receiver Device Driver Device Q D 50 50 V TT V TT = V CC -- 2.0 V Figure 5. Typical Termination for Output Driver and Device Evaluation MOTOROLA 6 TIMING SOLUTIONS MC100ES6039 Marking Notes: Device Nomenclature 20-- Lead SOIC W/B Marking MC100ES6039DW MC100ES6039 Trace Code Identification for 20 SOIC: AWLYYWW "A" -- The First character indicates the Assembly location. "WL" -- The Second & Third characters indicate the Source Wafer Lot Tracking Code. "YY" -- The Fourth & Fifth characters indicate the Year device was assembled. "WW" -- The Sixth & Seventh characters indicate the Work Week device was assembled. The "Y" Year ALPHA CODES Year Month The "W" Work Week ALPHA CODES Work Week Code 1st 6 Months (WW01 - WW26) 2nd 6 Months (WW27 - WW52) A = 2003 FIRST 6 MONTHS WW01 -- WW26 A = WW01 A = WW27 B = 2003 SECOND 6 MONTHS WW27 -- WW52 B = WW02 B = WW28 C = 2004 FIRST 6 MONTHS WW01 -- WW26 C = WW03 C = WW29 D = 2004 SECOND 6 MONTHS WW27 -- WW52 D = WW04 D = WW30 E = 2005 FIRST 6 MONTHS WW01 -- WW26 E = WW05 E = WW31 F = 2005 SECOND 6 MONTHS WW27 -- WW52 F = WW06 F = WW32 G = 2006 FIRST 6 MONTHS WW01 -- WW26 G = WW07 G = WW33 H = 2006 SECOND 6 MONTHS WW27 -- WW52 H = WW08 H = WW34 I = 2007 FIRST 6 MONTHS WW01 -- WW26 I = WW09 I = WW35 J = 2007 SECOND 6 MONTHS WW27 -- WW52 J = WW10 J = WW36 K = 2008 FIRST 6 MONTHS WW01 -- WW26 K = WW11 K = WW37 L = 2008 SECOND 6 MONTHS WW27 -- WW52 L = WW12 L = WW38 M = 2009 FIRST 6 MONTHS WW01 -- WW26 M = WW13 M = WW39 N = 2009 SECOND 6 MONTHS WW27 -- WW52 N = WW14 N = WW40 O = 2010 FIRST 6 MONTHS WW01 -- WW26 O = WW15 O = WW41 P = 2010 SECOND 6 MONTHS WW27 -- WW52 P = WW16 P = WW42 Q = 2011 FIRST 6 MONTHS WW01 -- WW26 Q = WW17 Q = WW43 R = 2011 SECOND 6 MONTHS WW27 -- WW52 R = WW18 R = WW44 S = 2012 FIRST 6 MONTHS WW01 -- WW26 S = WW19 S = WW45 T = 2012 SECOND 6 MONTHS WW27 -- WW52 T = WW20 T = WW46 U = 2013 FIRST 6 MONTHS WW01 -- WW26 U = WW21 U = WW47 V = 2013 SECOND 6 MONTHS WW27 -- WW52 V = WW22 V = WW48 W = 2014 FIRST 6 MONTHS WW01 -- WW26 W = WW23 W = WW49 X = 2014 SECOND 6 MONTHS WW27 -- WW52 X = WW24 X = WW50 Y = 2015 FIRST 6 MONTHS WW01 -- WW26 Y = WW25 Y = WW51 Z = 2015 SECOND 6 MONTHS WW27 -- WW52 Z = WW26 Z = WW52 TIMING SOLUTIONS 7 MOTOROLA MC100ES6039 OUTLINE DIMENSIONS DW SUFFIX 20 LEAD SOIC PACKAGE CASE 751D--06 ISSUE H 0.25 B M A 10.55 10X 10.05 PIN'S NUMBER 1 2.65 2.35 0.25 0.10 20X 20 0.49 0.35 0.25 1.27 4 A 12.95 12.65 A 11 10 7.6 7.4 T B SEATING PLANE 20X 0.1 T 5 X45_ 0.32 0.23 1.0 0.4 SECTION A-- A MOTOROLA T A B 18X PIN 1 INDEX 0.75 0.25 6 M 8 NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. 2. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 3. DATUMS A AND B TO BE DETERMINED AT THE PLANE WHERE THE BOTTOM OF THE LEADS EXIT THE PLASTIC BODY. 4. THIS DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURRS. MOLD FLASH, PROTRUSION OR GATE BURRS SHALL NOT EXCEED 0.15mm PER SIDE. THIS DIMENSION IS DETERMINED AT THE PLANE WHERE THE BOTTOM OF THE LEADS EXIT THE PLASTIC BODY. 5. THIS DIMENSION DOES NOT INCLUDE INTER-- LEAD FLASH OR PROTRUSIONS. INTER-- LEAD FLASH AND PROTRUSIONS SHALL NOT EXCEED 0.25mm PER SIDE. THIS DIMENSION IS DETERMINED AT THE PLANE WHERE THE BOTTOM OF THE LEADS EXIT THE PLASTIC BODY. 6. THIS DIMENSION DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD WIDTH TO EXCEED 0.62mm. 7 0 TIMING SOLUTIONS MC100ES6039 NOTES TIMING SOLUTIONS 9 MOTOROLA MC100ES6039 NOTES MOTOROLA 10 TIMING SOLUTIONS MC100ES6039 NOTES TIMING SOLUTIONS 11 MOTOROLA MC100ES6039 Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. E Motorola Inc. 2003 HOW TO REACH US: JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3--20--1, Minami--Azabu, Minato--ku, Tokyo 106--8573, Japan 81--3--3440--3569 USA/EUROPE/LOCATIONS NOT LISTED: Motorola Literature Distribution P.O. Box 5405, Denver, Colorado 80217 1--800--521--6274 or 480--768--2130 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong 852--26668334 HOME PAGE: http://motorola.com/semiconductors MOTOROLA 12 MC100ES6039 TIMING SOLUTIONS