Positronic Industries Space application Subminiature-D Connectors GSFC S-311-P-4 GSFC S-311-P-10 MIL-DTL-24308 Maximum Torque Values for 4-40 UNC Threads TORQUE Nm in-lb in-oz Phos. Bronze 0.90 8.0 128 Brass 0.68 6.0 96 Aluminum 0.45 4.0 64 Nylon 0.11 1.0 16 MATERIAL These torque values are applicable for threads only and do not apply to hardware assemblies. These torque values are approximate and should not be accepted as accurate limits. Indeterminant factors in specific applications preclude the publication of accurate torque values for universal use. Unless otherwise specified, dimensional tolerances are: 1) 0.001 inches (0.03 mm) for male contact mating diameters. 2) 0.003 inches (0.08 mm) for contact termination diameters. 3) 0.005 inches (0.13 mm) for all other diameters. 4) 0.015 inches (0.38 mm) for all other dimensions. CATALOG NUMBER: C-005 REV. NC PUBLISHED IN THE UNITED STATES OF AMERICA Positronic Industries, Inc. believes the data contained herein to be reliable. Since the technical information is given free of charge, the User employs such information at his own discretion and risk. Positronic Industries, Inc. assumes no responsibility for results obtained or damages incurred from use of such information in whole or in part. Positronic Industries' FEDERAL SUPPLY CODE FOR MANUFACTURERS is Number 28198. This catalog should be accompanied by a copy of Positronic Industries' Subminiature-D Connector and Cable Accessory Catalog. Additional special application Subminiature-D Connector catalogs are available upon request. Contact our Factory Sales Office or your District Sales Manager for copies of these catalogs: INDUSTRIAL & MILITARY APPLICATION SUBMINIATURE-D CONNECTORS ENVIRONMENTAL-D CONNECTORS COMBO-D CONNECTORS DUAL-PORT CONNECTORS FILTER-D CONNECTORS TABLE OF CONTENTS SPACE NORMAL DENSITY SUBMINIATURE-D CONNECTORS ......................1 - 7 SND Series. Removable or fixed contacts, 7.5 ampere nominal rating. Crimp, solder and straight and 90 printed board mount contact terminations. Five connector variants, 9 through 50 contacts. Military quality connectors compatible with MIL-DTL24308, conforming to GSFC-S-311-P-4 and GSFCS-311-P-10 where applicable. SPACE DENSI-D SUBMINIATURE-D CONNECTORS .....................8 - 16 SDD Series. Removable or fixed contacts, 5 ampere nominal rating. Crimp and straight and 90 printed board contact terminations. Six connector variants, 15 through 104 contacts. Military quality connectors compatible with MIL-DTL-24308, conforming to GSFC-S-311-P-4 where applicable. SPACE COMBINATION CONTACT SUBMINIATURE-D CONNECTORS ....................17 - 43 SCBM SERIES . . . . . . . . . . . . . . . . . . . . . .17 - 35 Fixed signal contacts, Size 20, 7.5 ampere nominal rating. Size 8 shielded and power contacts. Solder cup and printed board mount contact terminations available on both Size 20 and Size 8 contacts. Twenty connector variants, 5W1 through 46W4, using shell sizes 1 through 6. Military quality connectors compatible with MIL-DTL-24308, conforming to GSFC-S-311-P-4 and GSFC-S-311-P-10 where applicable. SIZE 8 REMOVABLE CONTACTS . . . . . . . . . . . .27 Shielded and high voltage and power crimp and solder terminations. Functional in SCBM and SCBC connector bodies. - 34 SCBC SERIES . . . . . . . . . . . . . . . . . . . . . .32 - 43 Size 20 signal and Size 8 shielded and power removable contacts. Eleven connector variants, shell sizes 1 through 6. Military quality connectors compatible with MIL-DTL-24308, conforming to GSFC-S-311-P-4 where applicable. SPACE APPLICATION SUBMINIATURE-D CONNECTOR SAVERS .......................................44 - 47 SAD, SADD and SACBM Series connector savers. Normal density, 9 through 50 contacts. High density, 15 through 104 contacts. Combination size 20 contact/ Size 8 contact connectors using shell sizes 1 through 6. ACCESSORIES ...................................................48 - 54 QUALIFIED PARTS LIST DIRECTORY PER GSFC-311-QPLD .........................................55 - 57 SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES CRIMP CONTACTS CLOSED CRIMP BARREL FEMALE CONTACT ("CLOSED ENTRY" DESIGN) CO MALE CONTACT A A CO 0.030 O (0.76) 0.150 (3.81) BO 0.150 (3.81) Brass Shroud BO Crimp contacts may be supplied kitted with connector or ordered separately. PART NUMBER WIRE SIZE AWG/(mm2) A BO CO PART NUMBER WIRE SIZE AWG/(mm2) A BO CO FC8022D-50-1202.0 22 / 24 / 26 / 28 / 30 (0.3/0.25/0.12/0.08/0.05) 0.518 (13.16) 0.035 (0.89) 0.047 (1.19) MC8022D-50 22 / 24 / 26 / 28 / 30 (0.3/0.25/0.12/0.08/0.05) 0.531 (13.49) 0.035 (0.89) 0.047 (1.19) Material: Leaded nickel copper. Plating: 0.000050 inch (1.25 ) gold over copper. Material: Brass. Plating: 0.000050 inch (1.25 ) gold over copper. REELS FOR AUTOMATIC FEED PNEUMATIC CRIMP TOOLS Contacts may be supplied in plastic carriers, packaged in reels holding 2,000 contacts for use with the automatic feed pneumatic crimp tools, catalog part number 9550-1. The same type carrier is used for both male and female contacts. All male and female crimp contacts can be ordered in reels by adding letter "R" after the contact part number, such as MC8022DR-50 for a male contact and FC8022DR-50-1202.0 for female contact. Enlarged section of plastic contact carriers For SDD crimping information and crimp tools, see pages 13, 14, and 16. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 10 Industries, Inc. SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES STRAIGHT PRINTED BOARD MOUNT CONTACTS FEMALE CONTACT ("CLOSED ENTRY" DESIGN) MALE CONTACT A A 0.030 O (0.76) DO Brass Shroud DO Straight printed board mount contacts are supplied in the connector. CODE NUMBER L DO A 3 0.150 (3.81) 0.020 (0.51) 0.725 (18.42) 32 0.300 (7.62) 0.020 (0.51) 0.865 (21.97) For straight printed board mount contacts, specify Code Number in Step 4 of the Ordering Information. CODE NUMBER L DO A 3 0.150 (3.81) 0.020 (0.51) 0.737 (18.72) 32 0.300 (7.62) 0.020 (0.51) 0.877 (22.28) Fixed Female Jackscrews Contact Material: Phosphor bronze. Plating: 0.000050 inch (1.25 ) gold over copper. Typical Part Number: SDD62F3S60T2G Swaged spacer with pushon fastener; phosphor bronze. 0.375 (9.53) L 0.020(0.51) O 90 PRINTED BOARD MOUNT CONNECTOR CODE 4, 0.450(11.43) CONTACT EXTENSION C SDD004R7000 0.450(11.43) CONTACT EXTENSION 0.082(2.08), Typical 0.082(2.08), Typical 0.082(2.08), Typical Fixed Female Jackscrews 0.008 B A PART NUMBER A B C D SDD1504R7000 1.204 (30.58) 0.984 (24.99) 0.528 (13.41) 0.450 (11.43) SDD2604R7000 1.532 (38.91) 1.312 (33.32) 0.528 (13.41) 0.450 (11.43) SDD4404R7000 2.072 (52.63) 1.852 (47.04) 0.528 (13.41) 0.450 (11.43) SDD6204R7000 2.720 (69.09) 2.500 (63.50) 0.528 (13.41) 0.450 (11.43) SDD7804R7000 2.626 (66.70) 2.406 (61.11) 0.573 (14.55) 0.450 (11.43) SDD10404R7000 2.720 (69.09) 2.500 (63.50) 0.614 (15.60) 0.450 (11.43) 0.082(2.08), Typical D Typical Part Number: SDD104M4R7NT2G 0.082(2.08), Typical 0.082(2.08), Typical 0.082(2.08), Typical Specify Code 4 in Step 4 of the Ordering Information. D Numbering shown is rear view of male and face view of female. 0.078(1.98), Typical 0.078(1.98), Typical Typical Part Number: SDD44F4R7NT2G 11 Positronic Industries, Inc. 0.020(0.51) O Push-on Fastener; Beryllium Copper. 0.125(3.18), Nominal D Typical Part Number: SDD78M4R7NT2G DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES 90 AND STRAIGHT PRINTED BOARD CONTACT HOLE PATTERN Mount connector with mating face positioned to follow direction of arrows. 0.984(24.99) SDD15 MALE 0.190(4.83) 0.492 (12.50) 2.500(63.50) SDD62 MALE 0.078 (1.98) 0.973 (24.71) 1.250(31.75) 0.078 (1.98) 0.078 (1.98) 0.090(2.29), Typical 0.984(24.99) SDD15 FEMALE 0.095(2.41), Typical 0.215(5.46) 0.078 (1.98) 0.492 (12.50) 2.500(63.50) 0.078 (1.98) 0.090(2.29), Typical SDD62 FEMALE 0.975 (24.77) 1.250(31.75) 1.312(33.32) 0.078 (1.98) 0.078 (1.98) SDD26 MALE 0.380(9.65) 0.078 (1.98) 0.656 (16.66) 0.095(2.41), Typical SDD26 FEMALE 0.090(2.29), Typical 1.312(33.32) 0.078 (1.98) 0.078 (1.98) 2.406(61.11) SDD78 MALE 0.385(9.78) 0.078 (1.98) 0.656 (16.66) 0.903 (22.94) 1.203(30.56) 0.082 (2.08) 0.078 0.090(2.29), Typical (1.98) SDD44 MALE 0.041(1.04) 1.852(47.04) 0.095(2.41), Typical 0.650(16.51) 0.926(23.52) 0.078 (1.98) 0.082 (2.08) 0.082 (2.08) 2.406(61.11) 0.090(2.29), Typical SDD44 FEMALE 0.078 (1.98) SDD78 FEMALE 0.903 (22.94) 0.082 (2.08) 1.852(47.04) 0.655(16.64) 0.926(23.52) 0.078 (1.98) 0.090(2.29), Typical SDD104 MALE 1.203(30.56) 0.078 (1.98) 0.082 (2.08) 1.250(31.75) 1.250(31.75) 0.095(2.41), Typical SDD104 FEMALE 2.500(63.50) 2.500(63.50) 0.967(24.56) 0.095(2.41), Typical 0.082 (2.08) 0.041(1.04) 0.082(2.08), Typical 0.082(2.08), Typical 0.967 (24.56) 0.095(2.41), Typical Suggest 0.035(0.89) O hole for contact termination positions. Suggest 0.123 0.003(3.12) O hole for mounting connector with push-on fasteners. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 12 Industries, Inc. SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES CRIMPING INFORMATION FOR SDD SERIES CRIMP CONTACTS USE INDICATED POSITRONIC TOOLS FOR BEST RESULTS Step 1: Strip wire to indicated length. Insulation Take Care Not To: - Damage or remove strands. Untwist or overtwist strands. Leave insulation particles on strands. Damage insulation. 0.010 0.150 (3.81) Stranded Wire Correctly Stripped Wire Strands damaged or removed by stripping tool. Strands overtwisted. Particles of insulation on the stripped part of the wire. Insulation cut incorrectly. Wire insulation damaged. Strands untwisted. Examples of Stripping Faults Step 2: Crimp wire to contact. For Hand Crimp Tool: - Place contact into crimping tool. - Insert wire into contact. - Center contact by slowly closing the crimping tool until the crimp indenters make contact with the crimp barrel. - Complete the cycle of the crimping tool in one smooth motion. - Remove the crimped contact. For Automatic Feed Pneumatic Crimp Tool: - Insert the wire into the contact, positioned in the crimp tool by the plastic carrier. - Depress the activating device of the crimping tool to start the crimping cycle. - Remove the crimped contact. 13 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES CRIMPING INFORMATION FOR SDD SERIES CRIMP CONTACTS Step 3: Inspect the crimp. For All Tools: - Strands to be visible through the inspection hole. - Strands not to be visible beyond the insulation support. - Crimped contact to meet recommended conductor tensile Crimp to meet recommended force shown in chart. tensile strength. - Check for peeled gold and bent contacts. Wire Insulation, Typical Cross Section of Correctly Crimped Contact Correctly Crimped Contact Stripped wires compressed for improved conduction. Strands visible beyond insulation support. 8 Crimp Indents Strands not visible through inspection hole. Crimp indents too close to inspection hole. Stripped part of the wire too long. Stripped part of the wire too short. Crimp indents incorrectly located. Examples of Crimping Faults Positronic Recommended Conductor Tensile Strength WIRE SIZE AWG/(mm2) AXIAL LOAD POUNDS/(N) 22 (0.3) 12 (53) 24 (0.25) 8 (36) 26 (0.12) 5 (22) 28 (0.08) 3 (13) 30 (0.05) 1.5 (4.4) Conductor tensile strength values are derived using silver tin-plated copper wires. Values may change depending upon what type of wire is used. Positronic Recommended Tools CRIMP TOOLS POSITIONERS FOR FC8022D-50-1202.2 POSITIONERS FOR MC8022D-50 9507, HAND CRIMP TOOL 9502-3 9502-4 9550-1, AUTOMATIC FEED, PNEUMATIC STRIP AND CRIMP TOOL Supplied in reels. Supplied in reels. See page 16 for contact crimping tool information. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 14 Industries, Inc. SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS SDD SERIES ORDERING INFORMATION - CODE NUMBERING SYSTEM Specify the complete connector by following Steps 1 through 9. Insert "0" when a step is not used. STEP 1 2 3 4 5 6 7 8 SDD 62 F 4 R7 N T6 G 9 STEP 1 - Basic Series STEP 9 - Special Options SDD Series Consult Sales Department. STEP 2 - SDD Series Connector Variants STEP 8 - Shell Options 15, 26, 44, 62, 78, 104 G - Gold over Copper Plate. D - Gold over Copper Plate and Dimpled. STEP 3 - Connector Gender M -Male F -Female STEP 4 - Contact Termination Type 0 1 3 32 4 - Ordered without contacts. Crimp, 22 AWG - 30 AWG (0.3 mm2 - 0.05 mm2). Solder, Straight Printed Board Mount with 0.150(3.81) Tail Length. Solder, Straight Printed Board Mount with 0.300(7.62) Tail Length. Solder, 90 Printed Board Mount with 0.450(11.43) Contact Extension. STEP 7 - Locking and Polarizing Systems 0 T T2 T6 E E2 E6 - None. - Fixed Female Jackscrews. - Fixed Female Jackscrews. - Fixed Male and Female Polarized Jackscrews. - Rotating Male Jackscrews. - Rotating Male Screw Locks. - Rotating Male and Female Polarized Jackscrews. STEP 6 - Hoods and Push-On Fasteners STEP 5 - Mounting Style 0 B3 F P R2 - R6 R7 R8 S S2 S5 S6 15 - Mounting Hole, 0.120(3.05) O. Bracket, Mounting, 90 Metal with Cross Bar. Float Mounts, Universal. Threaded Post, Brass, 0.375(9.53) Length. Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Thread Fixed Female Jackscrews with Cross Bar. Bracket, Mounting, 90 Metal, Swaged to Connector with 0.120 (3.05) O Mounting Hole with Cross Bar. Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Threads with Cross Bar. Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Locknut with Cross Bar. Swaged Spacer, 4-40 Threads, 0.375(9.53) Length. Swaged Spacer, 4-40 Threads, 0.125(3.18) Length. Swaged Locknut, 4-40 Threads. Swaged Spacer with Push-on Fastener, 4-40 Threads, 0.375(9.53) Length. Positronic Industries, Inc. 0 - None. H - Hood, Top Opening, Brass. M - Hood, Top Opening, Aluminum, see page 52 for complete listing of options. N - Push-on Fastener for 90 Mounting Brackets. NOTE: For additional information on accessories listed in Steps 5, 6, and 7, see the Accessory Section, pages 48-54. For SDD crimping tool information, see pages 13, 14, and 16. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SDD SERIES SPACE FLIGHT APPLICATION, HIGH DENSITY SUBMINIATURE-D CONNECTORS AUTOMATIC FEED, STRIP AND CRIMP TOOL, PNEUMATICALLY ACTUATED Part No. 9550-1 This fast-cycling automatic feed, strip and crimp tool produces an 8 indent crimp on wire sizes 22 AWG (0.3 mm2) through 30 AWG (0.05 mm2). SDD Series contacts must be ordered on reels. To order, specify part number 9550-1. Foot control valve is supplied as a standard accessory. MINIATURE STEP ADJUSTABLE TOOL (M22520/2-01) Part No. 9507 This miniature step adjustable hand crimping tool produces an 8 indent crimp configuration and will crimp wire sizes 22 AWG (0.3 mm2) through 30 AWG (0.05 mm2). To crimp female contacts, order contact positioner 9502-3. To crimp male contacts, order contact positioner 9502-4. Each positioner is equipped with a data plate which gives the correct crimp-depth setting for each wire size, and must be used with 9507 tool frame for best results when crimping SDD Series contacts. INSERTION/REMOVAL TOOL (M81969/1-04) One end of this tool is used to insert contacts into SDD Series connectors. The other end is used to extract contacts. This is accomplished by sliding the extraction tip down the wire into the connector until it bottoms against the contact. A slight rotation while pushing will release the contacts, which are then extracted by simultaneously pulling on the wire. Positronic 16 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS Space Combo-D Series Size 20 Signal Contacts, Fixed Solder Cup and Printed Board Mountable Size 8 Shielded and Power Removable, Printed Board Mountable Space Application Quality Connectors Space Combination Contact Subminiature-D connectors, Series SCBM, are space flight application quality rectangular connectors designed especially to withstand the rigors of launch and subsequent extended space flight. The SCBM Series features fixed contacts having solder cup terminations and printed board mount terminations for panel mounting and 90 and straight printed board applications. The materials, dimensions, and performance of the SCBM Series conform to the requirements of DESC drawing 85039 and GSFC S-311-P-10 where applicable. The SCBM Series fully complies to the outgassing requirements of ASTM E-595 and NASA-RP-1124. The SCBM Series utilizes precision machined contacts with the female contact featuring a "Closed-Entry" design having a brass protective shroud. Twenty standard combination contact variants are available, utilizing six shell sizes. Each connector variant is offered with contact terminations for solder cup and 90 terminations for printed board mounting. Nonmagnetic cable supports and jackscrew systems are available. Visual and mechanical inspection per MIL-DTL-24308 is performed, additional testing is available. Contact Technical Sales. SCBM SERIES CONTACT VARIANTS FACE VIEW OF MALE OR REAR VIEW OF FEMALE SHELL SIZE 1 SHELL SIZE 2 3W3 5W1 7W2 11W1 SHELL SIZE 3 5W5 9W4 13W3 17W2 21W1 SHELL SIZE 4 8W8 13W6 17W5 21WA4 25W3 27W2 SHELL SIZE 5 24W7 36W4 43W2 SHELL SIZE 6 47W1 17 Positronic Industries, Inc. 46W4 SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES SCBM SERIES TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: MECHANICAL CHARACTERISTICS: Insulator: Signal Contacts, Fixed: Signal Contacts: Signal Contact Plating: Power Contacts: Power Contact Plating: Shielded Contacts: Shielded Contact Plating: Shells: Mounting Spacers and Brackets: Push-On Fasteners: Jackscrew Systems: Hoods: Glass-filled polyester per MIL-M-24519, UL 94V-0, ASTM E-595, NASA-RP-1124, blue color. Male Contacts: Precision machined brass alloy. Female Contacts: Precision machined high tensile phosphor bronze with brass shroud. 0.000050 inch (1.25 microns) gold over copper plate. Machined of high conductivity copper alloy for both male and female contacts. 0.000050 inch (1.25 microns) gold over copper plate. Male Contacts: Precision machined brass. Female Contacts: Precision machined high tensile phosphor bronze. Signal Contacts: 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Phosphor bronze or beryllium copper with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate or aluminum yellow chromate conversion or black anodize. ELECTRICAL CHARACTERISTICS: SIGNAL CONTACTS: Contact Current Rating: Initial Contact Resistance: Proof Voltage: POWER CONTACTS: Contact Current Rating: Initial Contact Resistance: Proof Voltage: 7.5 amps, nominal. 0.008 ohms, maximum. 1,000 V r.m.s. 10, 15, 20, 30, and 40 amperes, nominal. 0.005 ohms, maximum. 1,000 V r.m.s. SHIELDED CONTACTS: Initial Contact Resistance: Nominal Impedance: Insertion Loss: Size 20 contacts. Male Contact: 0.040 inch (1.02 mm) diameter. Female Contact: Closed entry design with brass shroud. Contact Retention in Insulator: Signal Contacts: 9 lbs. (40N). Power, and Shielded Contacts: 22 lbs. (98N). Resistance to Solder Iron Heat: 500F (260C) for 10 seconds duration per IEC 512-6. Signal Contact Terminations: Solder Contacts: 0.042 inch (1.06 mm) minimum hole diameter for 20 AWG (0.5 mm2) wire, maximum. Straight Printed Board Mount: 0.028 inch (0.71 mm) diameter. 90 Printed Board Mount: 0.028 inch (0.71 mm) diameter. Power Contacts, Removable, Crimp or Size 8 contacts. Male Contact: 0.142 Solder Terminations: inch (3.61 mm) diameter. Female Contact: Features Large Surface Area (L.S.A.) Closed entry design utilizing BeCu mechanical retention member. Male and female contacts have terminations for wire sizes 8, 12, and 16 AWG. Power Contacts, Printed Board Mount: Size 8 contact. Male Contact: 0.142 inch (3.61 mm) diameter. Printed board terminations with 0.078 inch (1.98 mm) and 0.125 inch (3.18 mm) diameters. Shielded Contacts, Removable: See table of maximum cable sizes for contact termination dimensions, pages 34 and 35. Shells: Male shells may be dimpled for EMI/ESD ground paths. Polarization: Trapezoidally shaped shells and polarized jackscrews. Mounting to Angle Brackets: Jackscrews and riveted fasteners with 0.120 inch (3.05 mm) diameter hole, and threaded riveted fasteners with 4-40 threads and polyester inserts. Mounting to Printed Board: Rapid installation push-on fasteners and threaded posts. Locking Systems: Jackscrews. Mechanical Operations: 1,000 operations per IEC 512-5. 0.008 ohms, maximum. 50 ohms. -0.46 dB at 1 GHz -1.5 dB at 2 GHz VSWR: 1.15 average at 1 GHz 1.56 average at 2 GHz Above values measured using frequency domain techniques. Proof Voltage: 1,000 V r.m.s. CONNECTOR: Insulator Resistance: 5 G ohms. Creepage and Clearance Distance: 0.039 inch (1.0 mm), minimum. Working Voltage: 300 V r.m.s. Residual Magnetism: 20 Gamma, maximum. CLIMATIC CHARACTERISTICS: Temperature Range: Damp Heat, Steady State: -55C to +125C. 21 days. SCBM5W5F85000G SCBM9W4M65000G Positronic 18 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES SCBM5W5M0000G SCBM3W3M0000G STANDARD SHELL ASSEMBLY M B K B1 0.050(1.27)0.010 D E H D1 0.120 (3.05) 0.005 O Mounting Hole, two places 0.220(5.59), Max. C A 10 Typical G 0.036(0.91)0.008 0.120(3.05) 0.010 0.120 (3.05)0.005 O Mounting Hole, two places 0.154 (3.91) O Mounting Hole available 0.032(0.81) Total diametral float OPTIONAL SHELL ASSEMBLY WITH UNIVERSAL FLOAT MOUNTS OPTIONAL SHELL ASSEMBLY 19 SHELL SIZE A 0.015 SHELL SIZE 1 MALE 1.213 (30.81) SHELL SIZE 1 FEMALE 1.213 (30.81) SHELL SIZE 2 MALE 1.541 (39.14) SHELL SIZE 2 FEMALE 1.541 (39.14) SHELL SIZE 3 MALE 2.088 (53.04) SHELL SIZE 3 FEMALE 2.088 (53.04) SHELL SIZE 4 MALE 2.729 (69.32) SHELL SIZE 4 FEMALE 2.729 (69.32) SHELL SIZE 5 MALE 2.635 (66.93) SHELL SIZE 5 FEMALE 2.635 (66.93) SHELL SIZE 6 MALE 2.729 (69.32) SHELL SIZE 6 FEMALE 2.729 (69.32) Positronic Industries, Inc. B 0.005 B1 0.005 C 0.005 0.666 (16.92) 0.984 (24.99) 0.643 (16.33) 0.984 (24.99) 0.994 (25.25) 0.971 (24.66) 1.511 (38.38) 2.159 (54.84) 2.079 (52.81) 2.064 (52.43) 2.212 (56.18) H 0.010 K 0.005 M 0.010 0.329 (8.36) 0.494 (12.55) 0.759 (19.28) 0.422 (10.72) 0.233 (5.92) 0.422 (10.72) 0.494 (12.55) 0.759 (19.28) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 1.083 (27.51) 0.422 (10.72) 0.233 (5.92) 0.422 (10.72) 0.494 (12.55) 1.083 (27.51) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 1.625 (41.28) 0.422 (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 (12.55) 1.625 (41.28) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 2.272 (57.71) 0.422 (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 (12.55) 2.272 (57.71) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.605 (15.37) 2.178 (55.32) 0.534 (13.56) 0.230 (5.84) 0.426 (10.82) 0.605 (15.37) 2.178 (55.32) 0.534 (13.56) 0.243 (6.17) 0.429 (10.90) 0.668 (16.97) 2.302 (58.47) 0.596 (15.14) 0.230 (5.84) 0.426 (10.82) 0.668 (16.97) 2.302 (58.47) 0.596 (15.14) 0.243 (6.17) 0.429 (10.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.441 (11.20) 0.423 (10.74) 2.500 (63.50) 2.500 (63.50) G 0.010 0.311 (7.90) 2.406 (61.11) 2.406 (61.11) E 0.015 0.329 (8.36) 2.500 (63.50) 2.500 (63.50) D1 0.005 0.311 (7.90) 1.852 (47.04) 1.852 (47.04) 2.182 (55.42) D 0.005 1.312 (33.32) 1.312 (33.32) 1.534 (38.96) 2.189 (55.60) 0.086 (2.18)+0.005 -0.000 O Mounting Hole, two places 0.503 (12.78) 0.485 (12.32) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES SOLDER CONNECTOR Fixed Female Jackscrews 20 AWG, max. (0.5 mm2) 0.125 (3.18) 0.345 (8.76) Fixed Female Jackscrew For solder contacts, specify Code 2 in Step 4 of the Ordering Information. Fixed Male Jackscrew Fixed male and female polarized jackscrews available. Specify Code T6 in Step 7 of the Ordering Information. Typical Part Number: SCBM7W2F200T6G Typical Part Number: SCBM7W2M200T2G STRAIGHT PRINTED BOARD MOUNT CONNECTOR WITH SIZE 8 CONTACTS CODE NUMBER DO 3 --------- 35 0.078 (1.98) 37 0.125 (3.18) Swaged spacer with push-on fastener, phosphor bronze. For straight printed board mount contacts, specify Code Number in Step 4 of the Ordering Information. SCBM21WA4M2000G WITH MS4820M Fixed Female Jackscrews 0.010 Min. (0.25) 0.170 (4.32) 0.250 (6.35) 0.028 O (0.71) DO Typical Part Number: SCBM17W2F35S60T2G SCBM21WA4F65S00G DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 20 Industries, Inc. SPACE FLIGHT APPLICATION COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES PRINTED BOARD MOUNTED POWER CONTACTS STRAIGHT PRINTED BOARD MOUNT POWER CONTACTS Straight printed board mount power contacts are mounted in connector when ordered. FEMALE CLOSED ENTRY, L.S.A. MALE 0.142 O (3.61) 0.626 (15.90) 0.170 (4.32) 0.634 (16.10) PART NUMBER AO CURRENT RATING PART NUMBER AO CURRENT RATING FDS4314M 0.078 (1.98) 15 Amps. MDS4314M 0.078 (1.98) 15 Amps. FDS4310M 0.125 (3.18) 30 Amps. MDS4310M 0.125 (3.18) 30 Amps. Material - High conductivity copper alloy. Plating - 0.000050 inch (1.25) gold over copper. RIGHT ANGLE PRINTED BOARD MOUNT POWER CONTACTS Right angle printed board mount power contacts are mounted in connector when ordered. 0.142 O (3.61) FEMALE CLOSED ENTRY, L.S.A. PART CURRENT A REF. NUMBER BO C SHELL SIZE BEND CODE BO C SHELL SIZE BEND CODE FRT4314M 15 Amps 0.580 (14.73) 0.078 (1.98) 0.339 (8.61) 1, 2, 3 & 4 55 MRT4314M 15 Amps 0.580 (14.73) 0.078 (1.98) 0.339 (8.61) 1, 2, 3 & 4 55 FRT4414M 15 Amps 0.692 (17.58) 0.078 (1.98) 0.451 (11.46) 5 55 MRT4414M 15 Amps 0.692 (17.58) 0.078 (1.98) 0.451 (11.46) 5 55 FRT4714M 15 Amps 0.661 (16.79) 0.078 (1.98) 0.420 1, 2, 3 & 4 (10.67) 75 MRT4714M 15 Amps 0.661 (16.79) 0.078 (1.98) 0.420 1, 2, 3 & 4 (10.67) 75 FRT4814M 15 Amps 0.773 (19.63) 0.078 (1.98) 0.520 (13.21) 75 MRT4814M 15 Amps 0.773 (19.63) 0.078 (1.98) 0.520 (13.21) 75 FRT4310M 30 Amps 1.036 (26.31) 0.125 (3.18) 0.810 1, 2, 3 & 4 (20.57) MRT4310M 30 Amps 1.036 (26.31) 0.125 (3.18) 0.810 1, 2, 3 & 4 (20.57) FRT4410M 30 Amps 1.036 (26.31) 0.125 (3.18) 0.810 (20.57) MRT4410M 30 Amps 1.036 (26.31) 0.125 (3.18) 0.810 (20.57) Material - High conductivity copper alloy. Plating - 0.000050 inch (1.25) gold over copper. DIMENSIONS ARE IN INCHES (MILLIMETERS) ALL DIMENSIONS SUBJECT TO CHANGE 21 PART CURRENT A REF. NUMBER Positronic Industries, Inc. 5 5 5 5 Note: Female power contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male and female contacts and reduced contact resistance during operation. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR WITH 0.125(3.18) O POWER CONTACTS C 0.220(5.59), Maximum CODE 5 AND 57, 0.283(7.19) CONTACT EXTENSION (30 AMPS NOMINAL) SCBM00R7000 0.283(7.19) CONTACT EXTENSION A Fixed Female Jackscrews 0.008 B SHELL SIZE A B C D SHELL SIZE 1 1.204 (30.58) 0.984 (24.99) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 2 1.532 (38.91) 1.312 (33.32) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 3 2.072 (52.63) 1.852 (47.04) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 4 2.720 (69.09) 2.500 (63.50) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 5 2.626 (66.70) 2.406 (61.11) 0.395 (10.03) 0.283 (7.19) 0.810 (20.57) Specify Code 5 or 57 in Step 4 of the Ordering Information. 0.112(2.84), Typical 0.810 (20.57) 0.112(2.84), Typical D 0.112(2.84), Typical Typical Part Number: SCBM17W2M57R7NT2G C 0.220(5.59), Maximum Numbering shown is rear view of male and face view of female. Push-on Fastener, Beryllium Copper. 0.170(4.32), Nominal D 0.125(3.18) O Typical Part Number: SCBM36W4F57R7NT2G 0.028(0.71) O RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR WITH 0.078(1.98) O POWER CONTACTS CODE 5 AND 55, 0.283(7.19) CONTACT EXTENSION (15 AMPS NOMINAL) SCBM00R7000 0.283(7.19) CONTACT EXTENSION A Fixed Female Jackscrews 0.008 B Specify Code 5 or 55 in Step 4 of the Ordering Information. SHELL SIZE A B C D SHELL SIZE 1 1.204 (30.58) 0.984 (24.99) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 2 1.532 (38.91) 1.312 (33.32) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 3 2.072 (52.63) 1.852 (47.04) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 4 2.720 (69.09) 2.500 (63.50) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 5 2.626 (66.70) 2.406 (61.11) 0.395 (10.03) 0.283 (7.19) 0.451 (11.56) 0.112(2.84), Typical 0.339 (8.61) D 0.112(2.84), Typical Typical Part Number: SCBM17W2M55R7NT2G Numbering shown is rear view of male and face view of female. Push-on Fastener, Beryllium Copper. 0.170(4.32), Nominal 0.112(2.84), Typical 0.078(1.98) O 0.028(0.71) O DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. D Typical Part Number: SCBM36W4F55R7NT2G Positronic 22 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES 0.125(3.18) O, Typical METRIC SYSTEM 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.078(1.98) O POWER CONTACTS CODE 7 AND 75, 0.370(9.40) CONTACT EXTENSION 0.220(5.59), Maximum (15 AMPS NOMINAL) SCBM00R7000 0.370(9.40) CONTACT EXTENSION 0.008 B Fixed Female Jackscrews A SHELL SIZE A B C D SHELL SIZE 1 1.204 (30.58) 0.984 (24.99) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 2 1.532 (38.91) 1.312 (33.32) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 3 2.072 (52.63) 1.852 (47.04) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 4 2.720 (69.09) 2.500 (63.50) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 5 2.626 (66.70) 2.406 (61.11) 0.470 (11.94) 0.370 (9.40) 0.520 (13.21) 0.100(2.54), Typical C Specify Code 7 or 75 in Step 4 of the Ordering Information. 0.100(2.54), Typical Numbering shown is rear view of male and face view of female. 0.420 (10.67) D D 0.100(2.54), Typical Typical Part Number: SCBM17W2M75R70T2G 0.170(4.32), Nominal 0.078(1.98) O 0.024(0.61) O Typical Part Number: SCBM36W4M75R70T2G METRIC SYSTEM 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.125(3.18) O POWER CONTACTS 0.125(3.18) O, Typical 0.220(5.59), Maximum CODE 7 AND 77, 0.370(9.40) CONTACT EXTENSION (30 AMPS NOMINAL) SCBM00R7000 0.370(9.40) CONTACT EXTENSION Fixed Female Jackscrews 0.008 B SHELL SIZE A B C D SHELL SIZE 1 1.204 (30.58) 0.984 (24.99) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 2 1.532 (38.91) 1.312 (33.32) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 3 2.072 (52.63) 1.852 (47.04) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 4 2.720 (69.09) 2.500 (63.50) 0.420 (10.67) 0.370 (9.40) SHELL SIZE 5 2.626 (66.70) 2.406 (61.11) 0.470 (11.94) 0.370 (9.40) A DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 0.810 (20.57) 0.100(2.54), Typical 0.100(2.54), Typical C Specify Code 7 or 77 in Step 4 of the Ordering Information. D Typical Part Number: SCBM17W2M77R70T2G 23 Numbering shown is rear view of male and face view of female. 0.810(20.57) Positronic Industries, Inc. D 0.100(2.54), Typical 0.170(4.32), Nominal 0.125(3.18) O 0.024(0.61) O Typical Part Number: SCBM36W4M77R70T2G SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES SHELL SIZE 6 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.078(1.98) O POWER CONTACTS CODE 5 AND 55, 0.283(7.19) CONTACT EXTENSION CONNECTOR VARIANT 46W4 (15 AMPS NOMINAL) Fixed Female Jackscrews 0.451(11.46) SHELL SIZE 6 CONNECTOR 0.008 2.500(63.50) 2.720(69.09) 0.507(12.88) 0.283(7.19) - Specify Code 5 or 55 in Step 4 of the Ordering Information. 0.112(2.84), Typical Typical Part Number: SCBM46W4M55R7NT2G 0.170(4.32), Nominal Numbering shown is rear view of male and face view of female. Push-on Fastener, Beryllium Copper. 0.078(1.98) O 0.028(0.71) O SHELL SIZE 6 90 PRINTED BOARD MOUNT CONNECTOR WITH 0.125(3.18) O POWER CONTACTS CODE 5 AND 57, 0.283(7.19) CONTACT EXTENSION CONNECTOR VARIANT 46W4 (30 AMPS NOMINAL) Fixed Female Jackscrews 0.451(11.46) SHELL SIZE 6 CONNECTOR 0.008 2.500(63.50) 2.720(69.09) 0.810 (20.57) 0.283(7.19) - Specify Code 5 or 57 in Step 4 of the Ordering Information. 0.112(2.84), Typical Typical Part Number: SCBM46W4M57R7NT2G 0.170(4.32), Nominal Numbering shown is rear view of male and face view of female. Push-on Fastener, Beryllium Copper. 0.125(3.18) O 0.028(0.71) O DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 24 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES RIGHT ANGLE AND STRAIGHT PRINTED BOARD CONTACT HOLE PATTERN WITH 0.078(1.98) O AND STRAIGHT PRINTED BOARD MOUNT 0.125(3.18) O POWER CONTACTS Hole identification shown for male connector; use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrows. 3W3 5W1 21W1 17W2 13W3 9W4 5W5 11W1 7W2 13W6 8W8 17W5 27W2 25W3 21WA4 24W7 43W2 36W4 25 CODE NUMBER 3, 35, & 37 5 & 55 7 & 75 X 0.112 (2.84) 0.112 (2.84) 0.100 (2.54) Y 0.056 (1.42) 0.056 (1.42) 0.050 (1.27) A 0.100 (2.54) 0.112 (2.84) 0.100 (2.54) B 0.050 (1.27) 0.056 (1.42) 0.050 (1.27) Positronic Industries, Inc. 47W1 46W4 Suggest Suggest Suggest Suggest DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 0.045(1.14) O hole for signal contact termination positions. 0.098(2.49) O hole for 0.078(1.98) O power contact terminations. 0.145(3.68) O hole for 0.125(3.18) O power contact termination positions. 0.123 0.003 (3.12) O hole for mounting connector with push-on fasteners. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES RIGHT ANGLE PRINTED BOARD CONTACT HOLE PATTERN WITH 0.125(3.18) O POWER CONTACTS Hole identification shown for male connector; use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrows. 5W1 3W3 11W1 7W2 9W4 21W1 17W2 13W3 8W8 13W6 21WA4 5W5 17W5 27W2 25W3 24W7 36W4 CODE NUMBER A B C X Y 5 & 57 0.471 0.415 0.359 (11.96) (10.54) (9.12) 0.112 (2.84) 0.056 (1.42) 7 & 77 0.390 (9.91) 0.100 (2.54) 0.050 (1.27) 0.340 (8.64) 0.290 (7.37) 46W4 Suggest 0.045(1.14) O hole for signal contact termination positions. Suggest 0.145(3.68) O hole for 0.125(3.18) O power contact termination positions. Suggest 0.123 0.003 (3.12) O hole for mounting connector with push-on fasteners. 43W2 47W1 DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 26 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES PRINTED BOARD MOUNT SHIELDED CONTACTS STRAIGHT PRINTED BOARD MOUNT SHIELDED CONTACTS STRAIGHT PRINTED BOARD MOUNT SHIELDED CONTACTS ARE MOUNTED IN CONNECTOR WHEN ORDERED. A 0.156 (3.96) C A 0.040 O (1.02) B 0.156 (3.96) B 0.200 (5.08) 0.200 (5.08) 0.152 O (3.86) FEMALE 0.037(0.94) across points MALE Suggest 0.045(1.14) O Hole 0.200 (5.08) PART NUMBER A B C PART NUMBER A B C FDS4201M 0.481 (12.22) 0.025 (0.64) 0.181 (4.60) MDS4201M 0.489 (12.42) 0.025 (0.64) 0.181 (4.60) 0.100(2.54) Material: Copper alloy with PTFE teflon insulator. Signal Contact Plating: 0.000050 inch (1.25 ) gold over copper. Contact Body Plating: 0.000050 inch (1.25 ) gold over copper. FDS4201M and MDS4201M Contact Hole Pattern Technical characteristics are listed on page 33. RIGHT ANGLE PRINTED BOARD MOUNT SHIELDED CONTACTS 90 PRINTED BOARD MOUNT SHIELDED CONTACTS ARE MOUNTED IN CONNECTOR WHEN ORDERED. A A B B FEMALE 0.162 (4.11) D Suggest 0.045(1.14) O Hole 0.037(0.94) across points 0.200 (5.08) MALE 0.162 (4.11) 0.152 O (3.86) 0.040 O (1.02) C C PART NUMBER A B C D PART NUMBER A B C D FRT4201M 0.827 (21.01) 0.240 (6.10) 0.259 (6.58) 0.470 (11.94) MRT4201M 0.829 (21.06) 0.240 (6.10) 0.253 (6.43) 0.470 (11.94) 0.100 (2.54) FRT4201M and MRT4201M Contact Hole Pattern Material: Copper alloy with PTFE teflon insulator. Signal Contact Plating: 0.000050 inch (1.25 ) gold over copper. Contact Body Plating: 0.000050 inch (1.25 ) gold over copper. Technical characteristics are listed on page 33. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 27 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES STRAIGHT PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS CODE 65, CONNECTOR WITH FDS4201M OR MDS4201M CONTACTS Fixed Female Jackscrews 0.250(6.35) 0.028 O (0.71) 0.170(4.32) Push-on Fastener, Phosphor Bronze 0.156(3.96) Numbering shown is rear view of male and face view of female. 0.025(0.64) 0.028(0.71) O 0.037(0.94) across points Typical Part Number: SCBM17W2M65S60T2G RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS CODE 85, CONNECTOR WITH FRT4201M OR MRT4201M CONTACTS SCBM00850000 0.283(7.19) CONTACT EXTENSION A 0.008 Fixed Female Jackscrews SHELL SIZE A B C D SHELL SIZE 1 1.204 (30.58) 0.984 (24.99) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 2 1.532 (38.91) 1.312 (33.32) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 3 2.072 (52.63) 1.852 (47.04) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 4 2.720 (69.09) 2.500 (63.50) 0.339 (8.61) 0.283 (7.19) SHELL SIZE 5 2.620 (66.70) 2.406 (61.11) 0.395 (10.03) 0.545 (13.84) B C Numbering shown is rear view of male and face view of female. 0.156(3.96) 0.170(4.32), Nominal D - Specify Code 85 in Step 4 of the Ordering Information. 0.112(2.84), Typical 0.470(11.94) Push-on Fastener, Beryllium Copper Typical Part Number: SCBM17W2M85R7NT2G 0.028 O (0.71) 0.028(0.71) O 1 place. 0.037(0.94) across points, 2 places. 0.470(11.94) 0.112(2.84), Typical D - Specify Code 85 in Step 4 of the Ordering Information. Typical Part Number: SCBM36W4M85R7NT2G NOTE: Shell size 5 connectors are supplied inverted when ordered with 90 printed board mount shielded contact. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 28 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES STRAIGHT PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FDS4201M AND MDS4201M SHIELDED CONTACTS Hole identification shown is for male connector; use mirror image for female connector. 3W3 5W1 7W2 5W5 11W1 17W2 13W3 9W4 21W1 8W8 17W5 21WA4 27W2 24W7 13W6 25W3 36W4 47W1 43W2 46W4 Suggest 0.045(1.14) O hole for signal contact termination position. Suggest 0.123 0.003 (3.12) O hole for mounting connector with push-on fastener. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 29 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES 90 PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FRT4201M AND MRT4201M SHIELDED CONTACTS Hole identification shown is for male connector; use mirror image for female connector. Mount connector with mating face positioned to follow direction of arrow. 3W3 5W1 7W2 11W1 5W5 9W4 17W2 13W3 21W1 13W6 8W8 21WA4 17W5 25W3 0.200 (5,08) 0.374 0.109 (2,77) Typ. (9,50) 0.109 (2,77) Typ. 0.055 (1,40) Typ. 0.100 (2,54) 0.075 (1,91) 0.374 (9,50) 0.270 (6,86) 0.270 (6,86) Typ. 0.540 (13,72) 0.810 (20,57) 1.203 (30,56) Typ. 1.203 (30,56) Typ. 27W2 24W7 0.109 (2,77) Typ. 0.112 (2,84) 0.112 (2,84) 0.055 (1,40) Typ. 36W4 0.112 (2,84) 0.109 (2,77) Typ. 0.112 (2,84) 0.055 (1,40) Typ. 0.100 (2,54) 0.100 (2,54) 0.150 (3,81) 0.810 (20,57) 0.150 (3,81) 0.540 (13,72) 0.200 (5,08) 0.810 (20,57) 0.075 (1,91) 1.203 (30,56) Typ. 0.200 (5,08) 0.075 (1,91) 1.203 (30,56) Typ. 47W1 43W2 Suggest 0.045(1.14) O hole for signal contact termination position. Suggest 0.123 0.003 (3.12) O hole for mounting connector with push-on fastener. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 30 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS SCBM SERIES ORDERING INFORMATION - CODE NUMBERING SYSTEM Specify the complete connector by following Steps 1 through 9. Insert "0" when a step is not used. STEP 1 2 SCBM 17W2 3 4 5 6 7 8 F 55 R7 N T2 G 9 STEP 1 - Basic Series STEP 9 - Special Options SCBM Series - Space Conformance with "Closed Entry" Signal Contacts Consult Sales Department. STEP 8 - Shell Options STEP 2 - Space Combo-D Series Connector Variants G - Gold over Copper Plate. D - Gold over Copper Plate and Dimpled. Shell Size 1 5W1 STEP 7 - Locking and Polarizing Systems Shell Size 2 3W3, 7W2, 11W1 0 T T2 T6 E E6 Shell Size 3 5W5, 9W4, 13W3, 17W2, 21W1 Shell Size 4 8W8, 13W6, 17W5, 21WA4, 25W3, 27W2 Shell Size 5 24W7, 36W4, 43W2, 47W1 STEP 6 - Hoods and Push-On Fasteners 0 - None. H - Hood, Top Opening, Brass. M - Hood, Top Opening, Aluminum, see page 52 for complete listing of options. N - Push-on Fastener for 90 Mounting Brackets. Shell Size 6 46W4 STEP 3 - Connector Gender M -Male F -Female STEP 4 - Contact Termination Type 2 3 - Solder, Signal Contacts only. - Solder, Straight Printed Board Mount with Signal Contacts, 0.170(4.32) Tail Length. 35 - Solder, Straight Printed Board Mount with Signal and 0.078(1.98) O Power Contacts, 0.170(4.32) Tail Length. 37 - Solder, Straight Printed Board Mount with Signal and 0.125(3.18) O Power Contacts, 0.170(4.32) Tail Length. 5 - Solder, 90 Printed Board Mount with Signal Contacts only, 0.283(7.19) Signal Contact Extension. 55 - Solder, 90 Printed Board Mount with Signal and 0.078(1.98) O Power Contacts, 0.283(7.19) Signal Contact Extension. 57 - Solder, 90 Printed Board Mount with Signal and 0.125(3.18) O Power Contacts, 0.283(7.19) Signal Contact Extension. 65 - Solder, Straight Printed Board Mount with Signal and Shielded Contacts, MDS/FDS 4201M footprint, 0.170(4.32) Signal Contact Tail Length. 7 - Solder, Metric System 90 Printed Board Mount with Signal Contacts only, 0.370(9.40) Signal Contact Extension. 75 - Solder, Metric System 90 Printed Board Mount with Signal and 0.078(1.98) O Power Contacts, 0.370(9.40) Signal Contact Extension. 77 - Solder, Metric System 90 Printed Board Mount with Signal and 0.125(3.18) O Power Contacts, 0.370(9.40) Signal Contact Extension. 85 - Solder, 90 Printed Board Mount with Signal and Shielded Contacts, MRT/FRT 4201M Footprint, 0.283(7.19) Signal Contact Extension. - None. - Fixed Female Jackscrews. - Fixed Female Jackscrews. - Fixed Male and Female Polarized Jackscrews. - Rotating Male Jackscrews. - Rotating Male and Female Polarized Jackscrews. STEP 5 - Mounting Style 0 B3 F P R2 R6 R7 R8 S S2 S5 S6 - Mounting Hole, 0.120(3.05) O. - Bracket, Mounting, 90 Metal with Cross Bar. - Float Mounts, Universal. - Threaded Post, Brass, 0.250(6.35) Length. - Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Thread Fixed Female Jackscrews with Cross Bar. - Bracket, Mounting, 90 Metal, Swaged to Connector with 0.120 (3.05) O Mounting Hole with Cross Bar. - Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Threads with Cross Bar. - Bracket, Mounting, 90 Metal, Swaged to Connector with 4-40 Locknut with Cross Bar. - Swaged Spacer, 4-40 Threads, 0.250(6.35) Length. - Swaged Spacer, 4-40 Threads, 0.125(3.18) Length. - Swaged Locknut, 4-40 Threads. - Swaged Spacer with Push-on Fastener, 4-40 Threads, 0.250(6.35) Length. NOTE: For additional information on accessories listed in Steps 5, 6, and 7, see the Accessory Section, pages 48-54. NOTE: Not available on Shell Size 6, CBD 46W4. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 31 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SCBM SERIES REMOVABLE POWER CONTACTS SOLDER POWER CONTACTS FEMALE - CLOSED ENTRY L.S.A. B MALE 0.142 O (3.61) C 0.402 (10.21) B C A A Solder contacts may be supplied kitted with connector or ordered separately. PART NUMBER CURRENT RATING WIRE SIZE A REF. BO CO PART NUMBER CURRENT RATING WIRE SIZE A REF. BO CO FS4008M 40 AMPS 8 0.858 (21.79) 0.219 (5.56) 0.188 (4.78) MS4008M 40 AMPS 8 0.868 (22.05) 0.219 (5.56) 0.188 (4.78) FS4012M 20 AMPS 12 0.858 (21.79) 0.143 (3.63) 0.112 (2.84) MS4012M 20 AMPS 12 0.868 (22.05) 0.143 (3.63) 0.112 (2.84) FS4016M 10 AMPS 16 0.858 (21.79) 0.100 (2.54) 0.069 (1.75) MS4016M 10 AMPS 16 0.868 (22.05) 0.100 (2.54) 0.069 (1.75) Material: High conductivity copper alloy. Plating: 0.000050 inch (1.25 ) gold over copper. REMOVABLE CRIMP CONTACTS POWER CONTACTS Crimp power contacts may be supplied with connector or ordered separately. FEMALE - CLOSED ENTRY L.S.A. MALE A A C 0.142 O (3.61) BO 0.354 (8.99) BO 0.354 (8.99) Material: High conductivity copper alloy. Plating: 0.000050 inch (1.25 ) gold over copper. PART NUMBER CURRENT RATING WIRE SIZE A REF. BO C MAX. PART NUMBER CURRENT RATING WIRE SIZE A REF. BO C MAX. FC4008M 40 AMPS 8 0.858 (21.79) 0.181 (4.60) 0.640 (16.26) MC4008M 40 AMPS 8 0.882 (22.40) 0.181 (4.60) 0.640 (16.26) FC4012M 20 AMPS 12 0.858 (21.79) 0.101 (2.57) 0.640 (16.26) MC4012M 20 AMPS 12 0.882 (22.40) 0.101 (2.57) 0.640 (16.26) FC4016M 10 AMPS 16 0.858 (21.79) 0.067 (1.70) 0.640 (16.26) MC4016M 10 AMPS 16 0.882 (22.40) 0.067 (1.70) 0.640 (16.26) 9509-0-0 Power Contact Hand Crimp Tool For use with *C4012M and *C4016M Contacts 9504-17 Power Contact Hand Crimp Tool For use with *C4008M Contacts NOTE: Female contacts feature Large Surface Area (L.S.A.) "Closed Entry" contact design which provides maximum mating surfaces between male and female contact and reduced contact resistance during operation. 4311-0-0 Power Contact Removal Tool DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 32 Industries, Inc. SCBC SCBM SERIES SPACE FLIGHT APPLICATION SIZE 8 REMOVABLE HIGH VOLTAGE AND SHIELDED CONTACTS REMOVABLE HIGH VOLTAGE CONTACTS High voltage contacts are not supplied with connectors and must be ordered separately. STRAIGHT SOLDER WIRE TERMINATION 20 AWG Max. 20 AWG Max. 0.734 (18.64) Ref. 0.734 (18.64) Ref. FS4820D MS4820D 0.485 (12.32) 0.142 O (3.61) 0.040 (1.02) O 90 SOLDER WIRE TERMINATION 20 AWG Max. 20 AWG Max. 0.697 (17.70) Ref. 0.697 (17.70) Ref. MS4920D FS4920D 0.142 (3.61) O 0.448 (11.38) 0.040 (1.02) O TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: MECHANICAL CHARACTERISTICS: Insulators: Contacts: Size 8 Removable Contacts: Durability: Vibration: Shock: Plating: Teflon, PTFE. Male contacts, brass. Female contacts, phosphor bronze. 0.000050 inch (1.25 microns) gold over copper. Rear insertion, front release. 500 cycles minimum. 20g from 10 Hz to 500 Hz. 30g-11ms. ELECTRICAL CHARACTERISTICS: HIGH VOLTAGE CONTACTS Flash Over Voltage: 3600 V r.m.s. Proof Voltage: 2700 V r.m.s. Initial Contact Resistance: 0.008 ohms maximum. CLIMATIC CHARACTERISTICS: Temperature Range: -55C to +125C. SHIELDED CONTACTS TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: Insulating Material: Inner Contacts: Outer Contacts: (Dielectric) Teflon, PTFE. Brass and Phosphor Bronze, 0.000050 inch (1.25 microns) gold over copper. Brass and Phosphor Bronze, 0.000050 inch (1.25 microns) gold over copper. ELECTRICAL CHARACTERISTICS: MECHANICAL CHARACTERISTICS: Removable Contacts: Durability: Vibration: Shock: Rear Insertion, front release. 500 cycles, minimum. 20g from 10 HZ to 500 HZ. 30g - 11 ms. CLIMATIC CHARACTERISTICS: Temperature Range: -55C to +125C. Initial Contact Resistance: 0.008 ohms, maximum. Nominal Impedance: 50 ohms. Insertion Loss: -0.46 dB at 1 GHz -1.5 dB at 2 GHz VSWR: 1.15 average at 1 GHz 1.56 average at 2 GHz Proof Voltage: 1,000 V r.m.s. Above values measured using frequency domain techniques. 33 Positronic Industries, Inc. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SCBC SCBM SERIES SPACE FLIGHT APPLICATION SIZE 8 REMOVABLE SHIELDED CONTACTS REMOVABLE SHIELDED CONTACTS Shielded contacts may be supplied kitted with connector or ordered separately. STRAIGHT SOLDER/CRIMP CONTACTS A A C BO BO FEMALE CONTACT 0.040 O (1.02) 0.152 O (3.86) MALE CONTACT STRAIGHT SOLDER/SOLDER CONTACTS A A C BO BO 0.040 O (1.02) FEMALE CONTACT 0.152 O (3.86) MALE CONTACT STRAIGHT CRIMP/CRIMP CONTACTS A A C BO BO FEMALE CONTACT 0.040 O (1.02) MALE CONTACT 0.152 O (3.86) Signal Contact Plating: 0.000050 inch (1.25 ) gold over copper. Contact Body Plating: 0.000050 inch (1.25 ) gold over copper. Material: Copper alloy with PTFE teflon insulator. PART NUMBER TYPE OF CONTACT MALE FEMALE A BO C MAX. RG CABLE NUMBER SOLDER/CRIMP MC4101M FC4101M 0.929 (23.60) 0.040 (1.02) 0.739 (18.77) 178 B/U 196 B/U SOLDER/CRIMP MC4102M FC4102M 0.929 (23.60) 0.067 (1.70) 0.739 (18.77) 179 B/U 316 /U SOLDER/CRIMP MC4103M FC4103M 1.037 (26.34) 0.108 (2.74) 0.847 (21.51) 180 B/U SOLDER/CRIMP MC4104M FC4104M 1.037 (26.34) 0.120 (3.05) 0.847 (21.51) 58 B/U SOLDER/SOLDER MS4101M FS4101M 0.929 (23.60) 0.040 (1.02) 0.739 (18.77) 178 B/U 196 B/U SOLDER/SOLDER MS4102M FS4102M 0.929 (23.60) 0.067 (1.70) 0.739 (18.77) 179 B/U 316 /U SOLDER/SOLDER MS4103M FS4103M 1.037 (26.34) 0.108 (2.74) 0.847 (21.51) 180 B/U SOLDER/SOLDER MS4104M FS4104M 1.037 (26.34) 0.120 (3.05) 0.847 (21.51) 58 B/U FCC4101M 0.929 (23.60) 0.040 (1.02) 0.739 (18.77) 178 B/U 196 B/U 0.067 (1.70) 0.739 (18.77) 179 B/U 316 /U CRIMP/CRIMP MCC4101M CRIMP/CRIMP MCC4102M FCC4102M 0.929 (23.60) CRIMP/CRIMP MCC4103M FCC4103M 1.037 (26.34) 0.108 (2.74) 0.847 (21.51) 180 B/U CRIMP/CRIMP MCC4104M FCC4104M 1.037 (26.34) 0.120 (3.05) 0.847 (21.51) 58 B/U Two-step crimping action for signal and shielding conductors. See page 35 for crimp tool and crimping information. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 34 Industries, Inc. SCBC SCBM SERIES SPACE FLIGHT APPLICATION SIZE 8 REMOVABLE SHIELDED CONTACTS SOLDERING AND CRIMPING INFORMATION FOR SCBC AND SCBM SERIES SHIELDED CONTACTS STEP 1: STRIP WIRE TO INDICATED LENGTH. A B C Insulation Braid Dielectric Center conductor TAKE CARE NOT TO: - Damage or remove strands. - Untwist or overtwist strands. - Leave insulation particles on strands. - Damage insulation. PART NUMBER RG CABLE NUMBER A B C CRIMP TOOL C4101M S4101M 178 B/U 0.281 (7.14) 0.250 (6.35) 0.078 (1.98) 9504-0 C4102M S4102M 179 B/U 316 /U 0.281 (7.14) 0.250 (6.35) 0.078 (1.98) 9504-0 C4103M S4103M 180 B/U 0.375 (9.53) 0.312 (7.92) 0.078 (1.98) 9504-0 C4104M S4104M 58 B/U 0.375 (9.53) 0.312 (7.92) 0.078 (1.98) 9504-0 CC4101M 178 B/U 0.281 (7.14) 0.250 (6.35) 0.120 (3.05) 9504-14 CC4102M 179 B/U 316 /U 0.281 (7.14) 0.250 (6.35) 0.120 (3.05) 9504-13 CC4103M 180 B/U 0.375 (9.53) 0.312 (7.92) 0.120 (3.05) 9504-15 CC4104M 58 B/U 0.375 (9.53) 0.312 (7.92) 0.120 (3.05) 9504-15 Contact gender is designated by M for male contacts and F for female contacts. Typical Part Number: FC4101M STEP 2: CRIMP WIRE TO CONTACT. Ferrule - Trim cable. - Slide ferrule over jacket. Insert dielectric and center conductor into barrel. Crimp center conductor into contact. - Butt ferrule against shoulder. Crimp ferrule over braid. Solder or crimp Jacket Barrel STEP 2: SOLDER WIRE TO CONTACT. Ferrule - Trim cable. Tin center conductor. - Slide ferrule over jacket. Insert dielectric and center conductor into barrel. Solder center conductor into contact. - Butt ferrule against shoulder. Solder cable to barrel through hole in ferrule. Solder cap into body. Solder Jacket Barrel STEP 2: SOLDER/CRIMP WIRE TO CONTACT. Cap - Trim cable. Tin center conductor. - Slide ferrule over jacket. Insert dielectric and center conductor into barrel. Solder center conductor into contact. - Butt ferrule against shoulder. Crimp ferrule over braid. Solder cap into body. Shielded Contact Hand Crimp Tool See Chart above for Crimp Tool Part Numbers. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 35 Positronic Industries, Inc. SCBC SERIES SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES Size 20 Signal Contacts, Crimp Removable Size 8 Shielded and Power Crimp Removable Contacts Space Application Quality Connectors Space Combination Contact Subminiature-D connectors, Series SCBC, are space flight application quality rectangular connectors designed especially to withstand the rigors of launch and subsequent space flight. The SCBC Series features crimp removable Size 20 signal contacts and Size 8 power and shielded contacts. The materials, dimensions, and performance of the SCBC Series conform to the requirements of DESC drawing 85039 and GSFC S-311-P-405 where applicable. The SCBC Series fully complies to the outgassing requirements of ASTM E-595 and NASA-RP-1124. The SCBC Series utilizes precision machined contacts with the female contact featuring a "Closed-Entry" design having a brass protective shroud. Eleven standard combination contact variants are available, utilizing six shell sizes. All connector variants of the SCBC Series are plug compatible with equivalent SCBM printed board mounted or panel mounted connectors. Nonmagnetic cable supports and jackscrew systems are available. Visual and mechanical inspection per MIL-DTL-24308 is performed, additional testing is available. Contact Technical Sales. SCBC SERIES CONTACT VARIANTS FACE VIEW OF MALE OR REAR VIEW OF FEMALE SHELL SIZE 1 NOTE: Additional contact variants may be tooled at customer request. 5W1 SHELL SIZE 2 7W2 11W1 SHELL SIZE 4 SHELL SIZE 3 13W3 17W2 21W1 25W3 SHELL SIZE 6 SHELL SIZE 5 36W4 47W1 43W2 46W4 Positronic 36 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES SCBC SERIES TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: MECHANICAL CHARACTERISTICS: Insulator: Signal Contacts, Crimp Removable: Contacts: Signal Contact Plating: Power Contacts: Power Contact Plating: Shielded Contacts: Shielded Contact Plating: Shells: Mounting Spacers: Jackscrew Systems: Hoods: Glass-filled polyester per MIL-M-24519, UL 94V-0, ASTM E-595, NASA-RP-1124, blue color. Male Contacts: Precision machined brass alloy. Female Contacts: Precision machined high tensile copper alloy with brass shroud; "Closed Entry" design. 0.000050 inch (1.25 microns) gold over copper plate. Machined of high conductivity copper alloy for both male and female contacts. 0.000050 inch (1.25 microns) gold over copper plate. Precision-machined copper alloy male contacts and female contacts. Retainers of beryllium copper. Signal Contact Plating: 0.000050 inch (1.25 microns) gold over copper. Shielded Body Plating: 0.000050 inch (1.25 microns) gold over copper. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate or aluminum with yellow chromate conversion or black anodize finish. ELECTRICAL CHARACTERISTICS: SIGNAL CONTACTS Contact Current Rating: Initial Contact Resistance: Proof Voltage: POWER CONTACTS Contact Current Rating: Initial Contact Resistance: Proof Voltage: SHIELDED CONTACTS Initial Contact Resistance: Nominal Impedance: Insertion Loss: Size 20 contact. Male Contact: 0.040 inch (1.02 mm) diameter. Female Contact: Closed entry design with brass shroud. Contact Retention in Insulator: 9 lbs. (40 N). Power and shielded - 22 lbs. (98 N). Crimp Contact Terminations: Closed barrel crimp, wire sizes 20 AWG (1.0 mm2) through 30 AWG (0.05 mm2). Power Contacts, Removable, Crimp or Solder Terminations: Size 8 contacts. Male Contact: 0.142 inch (3.61 mm) diameter. Female Contact: Features Large Surface Area (L.S.A.) Closed entry design utilizing BeCu mechanical retention member. Male and female contacts have terminations for wire sizes 8, 12, and 16 AWG. Shielded Contacts, Removable: See table of maximum cable sizes for contact termination dimensions, pages 34 and 35. Shells: Male shells may be dimpled for EMI/ESD ground paths. Polarization: Trapezoidally shaped shells and polarized jackscrews. Locking Systems: Jackscrews. Mechanical Operations, Signal Contacts: SCBC Series, 1,000 operations, closed entry contact with 0.000050 (1.25 microns) gold plating per IEC 512-5. CLIMATIC CHARACTERISTICS: 7.5 amperes, nominal. Temperature Range: Damp Heat, Steady State: -55C to +125C. 21 days. 0.008 ohms, maximum. 1,000 V r.m.s. 10, 15, 20, 30, and 40 amperes, nominal. 0.005 ohms, maximum. 1,000 V r.m.s. 0.008 ohms, maximum. 50 ohms. -0.46 dB at 1 GHz. -1.5 dB at 2 GHz. VSWR: 1.15 average at 1 GHz. 1.56 average at 2 GHz. Above values measured using frequency domain techniques. Proof Voltage: 1,000 V r.m.s. CONNECTORS Insulator Resistance: Clearance and Creepage Distance: Working Voltage: Residual Magnetism: 5 G ohms. 0.039 inch (1.0 mm), minimum. 300 V r.m.s. 20 Gamma, maximum. SCBC17W2M0000G WITH MC4101M SCBC17W2F0000G WITH FC4101M DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 37 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES SCBC17W2M0000G SCBC7W2F0000G STANDARD SHELL ASSEMBLY TYPICAL CONNECTOR TOP VIEW 0.375 (9.53) Max. M K 0.220 (5.59) Max. B 0.008 0.036(0.91) B1 0.010 0.050(1.27) D E H D1 0.220(5.59), Max. C 10 Typ. G 0.375(9.53), Max. A 0.120(3.05) 0.005 O Mounting Hole, two places OPTIONAL SHELL ASSEMBLY WITH UNIVERSAL FLOAT MOUNTS OPTIONAL SHELL ASSEMBLY 0.120(3.05) 0.010 0.120(3.05) 0.005 O Mounting Hole, two places 0.154(3.91) O Mounting Hole Available SHELL SIZE A 0.015 SHELL SIZE 1 MALE 1.213 (30.81) SHELL SIZE 1 FEMALE 1.213 (30.81) SHELL SIZE 2 MALE 1.541 (39.14) SHELL SIZE 2 FEMALE 1.541 (39.14) SHELL SIZE 3 MALE 2.088 (53.04) SHELL SIZE 3 FEMALE 2.088 (53.04) SHELL SIZE 4 MALE 2.729 (69.32) SHELL SIZE 4 FEMALE 2.729 (69.32) SHELL SIZE 5 MALE 2.635 (66.93) SHELL SIZE 5 FEMALE 2.635 (66.93) SHELL SIZE 6 MALE 2.729 (69.32) SHELL SIZE 6 FEMALE 2.729 (69.32) B 0.005 B1 0.005 C 0.005 0.666 (16.92) 0.984 (24.99) 0.643 (16.33) 0.984 (24.99) 0.994 (25.25) 0.971 (24.66) 1.511 (38.38) 2.159 (54.84) 2.500 (63.50) 2.079 (52.81) 2.064 (52.43) 2.212 (56.18) 2.189 (55.60) H 0.010 K 0.005 M 0.010 0.329 (8.36) 0.494 (12.55) 0.759 (19.28) 0.422 (10.72) 0.233 (5.92) 0.422 (10.72) 0.494 (12.55) 0.759 (19.28) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 1.083 (27.51) 0.422 (10.72) 0.233 (5.92) 0.422 (10.72) 0.494 (12.55) 1.083 (27.51) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 1.625 (41.28) 0.422 (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 (12.55) 1.625 (41.28) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 (12.55) 2.272 (57.71) 0.422 (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 (12.55) 2.272 (57.71) 0.422 (10.72) 0.243 (6.17) 0.429 (10.90) 0.605 (15.37) 2.178 (55.32) 0.534 (13.56) 0.230 (5.84) 0.426 (10.82) 0.605 (15.37) 2.178 (55.32) 0.534 (13.56) 0.243 (6.17) 0.429 (10.90) 0.668 (16.97) 2.302 (58.47) 0.596 (15.14) 0.230 (5.84) 0.426 (10.82) 0.668 (16.97) 2.302 (58.47) 0.596 (15.14) 0.243 (6.17) 0.429 (10.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.441 (11.20) 0.423 (10.74) 2.500 (63.50) 2.500 (63.50) G 0.010 0.311 (7.90) 2.406 (61.11) 2.406 (61.11) E 0.015 0.329 (8.36) 2.500 (63.50) 0.503 (12.78) 0.485 (12.32) 0.086(2.18) 0.005 -0.000 O Mounting Hole, two places D1 0.005 0.311 (7.90) 1.852 (47.04) 1.852 (47.04) 2.182 (55.42) D 0.005 1.312 (33.32) 1.312 (33.32) 1.534 (38.96) 0.032(0.81) Total Diametral Float DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 38 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES CRIMP REMOVABLE CONTACT CONNECTOR SIGNAL CRIMP CONTACTS CLOSED CRIMP BARREL FEMALE CONTACT ("CLOSED ENTRY" DESIGN) MALE CONTACT A A 0.040 O (1.02) BO BO Brass Shroud 0.170 (4.32) 0.170 (4.32) CO Contact Material: Leaded nickel copper. Plating: 0.000050 inch (1.25 ) gold over copper. CO Material: Brass. Plating: 0.000050 inch (1.25 ) gold over copper. PART NUMBER WIRE SIZE AWG/(mm2) A BO CO PART NUMBER WIRE SIZE AWG/(mm2) A BO CO FC6020D-50-1202.1 20 / 22 / 24 (0.5/0.3/0.25) 0.538 (13.67) 0.044 (1.12) 0.066 (1.68) MC6020D-50 20 / 22 / 24 (0.5/0.3/0.25) 0.550 (13.97) 0.044 (1.12) 0.066 (1.68) FC6026D-50-1202.1 26 / 28 / 30 (0.12/0.08/0.05) 0.538 (13.67) 0.027 (0.69) 0.066 (1.68) MC6026D-50 26 / 28 / 30 (0.12/0.08/0.05) 0.550 (13.97) 0.027 (0.69) 0.066 (1.68) Crimp contacts may be supplied kitted with connector or ordered separately. MALE CONTACT 18 AWG (1.0mm2) max. FEMALE CONTACT ("CLOSED ENTRY" DESIGN) 18 AWG (1.0mm2) max. 0.915 (23.24) 0.927 (23.55) 0.055 O (1.40) 0.055 O (1.40) 0.086 O (2.18) 0.170 (4.32) Brass Shroud Part number: FC6018M Material: Leaded nickel copper. Plating: 0.000050 inch (1.25 ) gold over copper. 0.040 O (1.02) 0.170 (4.32) 0.086 O (2.18) Part number: MC6018M Material: Brass. Plating: 0.000050 inch (1.25 ) gold over copper. REELS FOR AUTOMATIC FEED PNEUMATIC CRIMP TOOLS Contacts may be supplied in plastic carriers, packaged in reels holding 2,000 contacts for use with the automatic feed pneumatic crimp tools, catalog part number 9550-1. The same type carrier is used for both male and female contacts. All male and female crimp contacts can be ordered in reels by adding letter "R" after the contact part number, such as MC6020DR-50 for a male contact and FC6026DR-50-1202.1 for female contact. For SCBC crimping information and crimp tools, see pages 39, 40, 41 and 43. 39 Positronic Industries, Inc. Enlarged section of plastic contact carriers DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES CRIMPING INFORMATION FOR SND AND SCBC SERIES CRIMP SIGNAL CONTACTS CRIMP REMOVABLE CONTACT CONNECTOR USE INDICATED POSITRONIC TOOLS FOR BEST RESULTS Step 1: Strip wire to indicated length. Take Care Not To: - Insulation 0.020 0.160 (4.06) Damage or remove strands. Untwist or overtwist strands. Leave insulation particles on strands. Damage insulation. Stranded Wire Correctly Stripped Wire Strands damaged or removed by stripping tool. Strands overtwisted. Particles of insulation on the stripped part of the wire. Insulation cut incorrectly. Wire insulation damaged. Strands untwisted. Examples of Stripping Faults Step 2: Crimp wire to contact. For Hand Crimp Tool: - Place contact into crimping tool. - Insert wire into contact. - Center contact by slowly closing the crimping tool until the crimp indenters make contact with the crimp barrel. - Complete the cycle of the crimping tool in one smooth motion. - Remove the crimped contact. For Automatic Feed Pneumatic Crimp Tool: - Insert the wire into the contact, positioned in the crimp tool by the plastic carrier. - Depress the activating device of the crimping tool to start the crimping cycle. - Remove the crimped contact. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 40 Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES CRIMPING INFORMATION FOR SND AND SCBC SERIES CRIMP SIGNAL CONTACTS CRIMP REMOVABLE CONTACT CONNECTOR Step 3: Inspect the crimp. For All Tools: - Strands to be visible through the inspection hole. - Strands not to be visible beyond the insulation support. - Crimped contact to meet recommended conductor tensile Crimp to meet recommended force shown in chart. tensile strength. - Check for peeled gold and bent contacts. Wire Insulation, Typical Cross Section of Correctly Crimped Contact Correctly Crimped Contact Stripped wires compressed for improved conduction. Strands visible beyond insulation support. 8 Crimp Indents Strands not visible through inspection hole. Crimp indents too close to inspection hole. Stripped part of the wire too long. Positronic Recommended Conductor Tensile Strength WIRE SIZE AWG/(mm2) Stripped part of the wire too short. Crimp indents incorrectly located. Examples of Crimping Faults AXIAL LOAD POUNDS/(N) 20 (0.5) 20 (89) 22 (0.3) 12 (53) 24 (0.25) 8 (36) 26 (0.12) 5 (22) 28 (0.08) 3 (13) 30 (0.05) 1.5 (6.7) Positronic Recommended Tools SND AND SCBC SERIES CRIMP TOOLS POSITIONERS FOR FC6020D-50-1202.1 FC6026D-50-1202.1 MC6020D-50 MC6026D-50 9507, HAND CRIMP TOOL 9502-5 9550-1, AUTOMATIC FEED, PNEUMATIC STRIP AND CRIMP TOOL Supplied in reels. Conductor tensile strength values are derived using silver-tin plated copper wires. Values may change depending upon what type of wire is used. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 41 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES SCBC SERIES ORDERING INFORMATION - CODE NUMBERING SYSTEM Specify the complete connector by following Steps 1 through 9. Insert "0" when a step is not used. 1 STEP 2 SCBC 7W2 3 4 5 6 7 8 M 13 0 0 E D STEP 1 - Basic Series STEP 9 - Special Options SCBC Series Consult Sales Department. STEP 2 - SCBC Series Connector Variants STEP 8 - Shell Options Shell Size 1 5W1 Shell Size 2 7W2, 11W1 Shell Size 3 13W3, 17W2, 21W1 Shell Size 4 25W3 Shell Size 5 36W4, 43W2, 47W1 Shell Size 6 46W4 STEP 3 - Connector Gender M -Male F -Female 9 G - Gold over Copper Plate. D - Gold over Copper Plate and Dimpled. STEP 7 - Locking and Polarizing Systems 0 T T2 T6 E E2 E6 - None. - Fixed Female Jackscrews. - Fixed Female Jackscrews. - Fixed Male and Female Polarized Jackscrews. - Rotating Male Jackscrews. - Rotating Male Screw Locks. - Rotating Male and Female Polarized Jackscrews. STEP 6 - Hoods 0 - None. H - Hood, Top Opening, Brass. M - Hood, Top Opening, Aluminum, see page 52 for complete listing of options. STEP 4 - Contact Termination Type 0 - Connector ordered without contacts. Order Signal and Shielded contacts separately. See pages 32, 34, and 39 for contact part numbers. Kitted contacts supplied in sealed bags. 1 - Signal Contacts, 20 AWG - 24 AWG (0.5 mm2 - 0.25 mm2). 13 - Signal Contacts, 20 AWG - 24 AWG (0.5 mm2 - 0.25 mm2) with MCC/FCC 4101M Shielded Contacts. 14 - Signal Contacts, 20 AWG - 24 AWG (0.5 mm2 - 0.25 mm2) with MCC/FCC 4102M Shielded Contacts. NOTE: For additional information on accessories listed in Steps 5, 6, and 7, see the Accessory Section, pages 48-54. STEP 5 - Mounting Style 0 F S2 S5 - Mounting Hole, 0.120(3.05) O. Float Mounts, Universal. Swaged Spacer, 4-40 Threads, 0.125(3.18) Length. Swaged Locknut, 4-40 Threads. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 42 Industries, Inc. SCBC SERIES SPACE FLIGHT APPLICATION, COMBINATION CONTACT SUBMINIATURE-D CONNECTORS CRIMP REMOVABLE CONTACT SERIES AUTOMATIC FEED, STRIP AND CRIMP TOOL, PNEUMATICALLY ACTUATED Part No. 9550-1 This fast-cycling automatic feed, strip and crimp tool produces an 8 indent crimp on wire sizes 20 AWG (0.5 mm2) through 30 AWG (0.05 mm2). SND and SCBC Series contacts must be ordered on reels. To order, specify part number 9550-1. Foot control valve is supplied as a standard accessory. MINIATURE STEP ADJUSTABLE TOOL (M22520/2-01) Part No. 9507 This miniature 8 step adjustable hand crimping tool produces an 8 indent crimp configuration and will crimp wire sizes 20 AWG (0.5 mm2) through 30 AWG (0.05 mm2). To crimp wire size 20 AWG (0.5 mm2) through 30 AWG (0.05 mm2), order contact positioner 9502-5. Each positioner is equipped with a data plate which gives the correct crimp depth setting for each wire size, and must be used with 9507 tool frame for best results when crimping SND and SCBC Series contacts. INSERTION/REMOVAL TOOL (M81969/1-02) One end of this tool is used to insert contacts into SND and SCBC Series connectors. The other end is used to extract contacts. This is accomplished by sliding the extraction tip down the wire into the connector until it bottoms against the contact. A slight rotation while pushing will release the contacts, which are then extracted by simultaneously pulling on the wire. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 43 Positronic Industries, Inc. Space Adapter Series SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY SUBMINIATURE-D CONNECTOR SAVERS Series SAD Size 20 Contacts Series SADD Size 22 Contacts Series SACBM Size 20 and Size 8 Contacts Connector Saver Space Adapter-D Series connectors are space flight application connectors that function as connector savers. The normal density SAD Series is available in five standard connector variants of 9, 15, 25, 37 and 50 contacts. The high density SADD Series is available in six standard connector variants of 15, 26, 44, 62, 78 and 104 contacts. The SACBM Series is available in twenty standard combination contact variants. Space Adapter-D Series connectors utilize precision machined contacts for strength and durability. The female contact features a rugged "Closed Entry" design having a brass shroud. The materials and finishes, as well as the technical characteristics of the Space Adapter-D Series connectors conform to MIL-DTL-24308, GSFC S-311-P-4 and GSFC S-311-P-10. Visual and mechanical inspection per MIL-DTL-24308 is performed, additional testing is available. Contact Technical Sales. SPACE ADAPTER-D SERIES TECHNICAL CHARACTERISTICS MATERIALS AND FINISHES: MECHANICAL CHARACTERISTICS: Insulator: Fixed Contacts: Contacts: Contact Plating: Shells: Glass-filled DAP per ASTM-D-5948 or polyester glass-filled per MIL-M-24519, UL 94V0, ASTM E-595, NASA-RP-1124. Precision machined high tensile copper alloy with brass shrouds. 0.000050 inch (1.25 microns) gold over copper plate. Brass with 0.000050 inch (1.25 microns) gold over copper plate. ELECTRICAL CHARACTERISTICS: Contact Current Rating: 40 amperes, nominal, Size 8. 7.5 amperes, nominal, Size 20. 5 amperes, nominal, Size 22. Initial Contact Resistance: 0.008 ohms, maximum. Proof Voltage: 1,000 V r.m.s. Insulator Resistance: 5 G ohms. Clearance and Creepage Distance: 0.039 inch (1.0 mm), minimum. Working Voltage: 300 V r.m.s. Residual Magnetism: 20 Gamma, maximum. Connector Saver: Contact Retention: Shells: Polarization: Mechanical Operations: Size 8 Contact: 0.142 inch (3.61 mm) diameter. Female Contact: Features large surface area (L.S.A.) closed entry design utilizing BeCu mechanical retention member. Size 20 Contact: 0.040 inch (1.02 mm) diameter. Female Contact: Closed entry design with brass shroud. Size 22 Contact: 0.030 inch (0.76 mm) diameter. Female Contact: Closed entry design with brass shroud. Male to female. 9 lbs. (40 N). Male shells may be dimpled for EMI/ESD ground paths. Trapezoidally shaped shells. 1,000 operations, minimum, per IEC 512-5. CLIMATIC CHARACTERISTICS: Temperature Range: -55C to +125C. Positronic 44 Industries, Inc. SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY SUBMINIATURE-D CONNECTOR SAVERS SAD SERIES CONNECTOR VARIANTS FACE VIEW OF MALE SAD9 SAD25 SAD15 SAD37 SAD50 MALE TO FEMALE CONNECTOR SAVER SIZE 20 CONTACTS 0.210(5.33) K E A 0.005 0.120 (3.05) O Thru Hole, 2 places D K1 B B1 C Female Contacts Male Contacts 0.018(0.46) D1 0.008 0.036(0.91) 0.020(0.51) Maximum Rollover Typical Part Number: SAD9M/F CONNECTOR PART NUMBER A 0.015 B 0.005 B1 0.005 C 0.005 D 0.005 D1 0.005 E 0.015 K 0.005 K1 0.005 SAD9M/F 1.213 (30.81) 0.643 (16.33) 0.666 (16.92) 0.984 (24.99) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.233 (5.92) SAD15M/F 1.541 (39.14) 0.971 (24.66) 0.994 (25.25) 1.312 (33.32) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.233 (5.92) SAD25M/F 2.088 (53.04) 1.511 (38.38) 1.534 (38.96) 1.852 (47.04) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.230 (5.84) SAD37M/F 2.729 (69.32) 2.159 (54.84) 2.182 (55.42) 2.500 (63.50) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.230 (5.84) SAD50M/F 2.635 (66.93) 2.064 (52.43) 2.079 (52.81) 2.406 (61.11) 0.423 (10.74) 0.441 (11.20) 0.605 (15.37) 0.243 (6.17) 0.230 (5.84) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 45 Positronic Industries, Inc. SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY SUBMINIATURE-D CONNECTOR SAVERS SADD SERIES CONNECTOR VARIANTS FACE VIEW OF MALE SADD15 SADD26 SADD44 SADD62 SADD78 SADD104 MALE TO FEMALE CONNECTOR SAVER SIZE 22 CONTACTS 0.210(5.33) K E A 0.005 0.120 (3.05) O Thru Hole, 2 places D K1 B B1 C Female Contacts Male Contacts 0.018(0.46) D1 0.008 0.036(0.91) 0.020(0.51) Maximum Rollover Typical Part Number: SADD15M/F CONNECTOR PART NUMBER A 0.015 B 0.005 B1 0.005 C 0.005 D 0.005 D1 0.005 E 0.015 K 0.005 K1 0.005 SADD15M/F 1.213 (30.81) 0.643 (16.33) 0.666 (16.92) 0.984 (24.99) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.233 (5.92) SADD26M/F 1.541 (39.14) 0.971 (24.66) 0.994 (25.25) 1.312 (33.32) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.233 (5.92) SADD44M/F 2.088 (53.04) 1.511 (38.38) 1.534 (38.96) 1.852 (47.04) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.230 (5.84) SADD62M/F 2.729 (69.32) 2.159 (54.84) 2.182 (55.42) 2.500 (63.50) 0.311 (7.90) 0.329 (8.36) 0.494 (12.55) 0.243 (6.17) 0.230 (5.84) SADD78M/F 2.635 (66.93) 2.064 (52.43) 2.079 (52.81) 2.406 (61.11) 0.423 (10.74) 0.441 (11.20) 0.605 (15.37) 0.243 (6.17) 0.230 (5.84) SADD104M/F 2.729 (69.32) 2.189 (55.60) 2.212 (56.18) 2.500 (63.50) 0.485 (12.32) 0.503 (12.78) 0.668 (16.97) 0.243 (6.17) 0.230 (5.84) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 46 Industries, Inc. SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY SUBMINIATURE-D CONNECTOR SAVERS SACBM SERIES CONNECTOR VARIANTS FACE VIEW OF MALE SHELL SIZE 2 SHELL SIZE 1 3W3 5W1 7W2 11W1 SHELL SIZE 3 5W5 9W4 13W3 17W2 21W1 SHELL SIZE 4 8W8 13W6 17W5 21WA4 25W3 27W2 SHELL SIZE 5 43W2 36W4 24W7 47W1 SHELL SIZE 6 46W4 MALE TO FEMALE CONNECTOR SAVER SIZE 20 AND SIZE 8 CONTACTS 0.210(5.33) E A C K O0.1200.005 (3.050.13) Thru hole, 2 places D K1 B1 B Female Contacts Male Contacts D1 0.018(0.46) 0.0360.008 (0.910.20) CONNECTOR SIZE SHELL SIZE 1 SHELL SIZE 2 SHELL SIZE 3 DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. SHELL SIZE 4 SHELL SIZE 5 47 Positronic Industries, Inc. SHELL SIZE 6 0.020(0.51) Max. rollover Typical Part Number: SACBM11W1M/F A 0.015 B 0.005 B1 0.005 C 0.005 D 0.005 D1 0.005 E 0.015 K 0.005 K1 0.005 1.213 (30.81) 1.541 (39.14) 2.088 (53.04) 2.729 (69.32) 2.635 (66.93) 2.729 (69.32) 0.643 (16.33) 0.971 (24.66) 1.511 (38.38) 2.159 (54.84) 2.064 (52.43) 2.189 (55.60) 0.666 (16.92) 0.994 (25.25) 1.534 (38.96) 2.182 (55.42) 2.079 (52.81) 2.212 (56.18) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 2.500 (63.50) 0.311 (7.90) 0.311 (7.90) 0.311 (7.90) 0.311 (7.90) 0.423 (10.74) 0.485 (12.32) 0.329 (8.36) 0.329 (8.36) 0.329 (8.36) 0.329 (8.36) 0.441 (11.20) 0.503 (12.78) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.605 (15.37) 0.668 (16.97) 0.243 (6.17) 0.243 (6.17) 0.243 (6.17) 0.243 (6.17) 0.243 (6.17) 0.243 (6.17) 0.233 (5.92) 0.233 (5.92) 0.230 (5.84) 0.230 (5.84) 0.230 (5.84) 0.230 (5.84) RIVETED-ON 90 MOUNTING BRACKETS AND PUSH-ON FASTENERS ACCESSORIES RIVETED ON RIGHT ANGLE MOUNTING BRACKETS 0.225 (5.72) Detail A 4-40 UNC Threads with Locknut 4-40 UNC Threads 0.120 (3.05) O Clearance Hole 4-40 UNC Threads 0.187 O (4.75) Detail B Mounting Bracket R6 R2 R7 Shells 0.015 (0.38) R8 Mounting Bracket Shells Mounting Bracket 4-40 UNC Threads R6 has 0.120 (3.05) O clearance hole. 4-40 UNC Threads 2.5 threads in metal, nominal. Polyester Insert 0.015 (0.38) DETAIL A DETAIL B Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. PUSH-ON FASTENER FOR RIVETED ON RIGHT ANGLE MOUNTING BRACKETS Printed Board 0.110 O Hole (2.79) Mounting Bracket SCBM17W2F5R7N0G (shown left) SDD26F4R7N0G (shown right) SAMPLE # PRINTED BOARD HOLE O INSERTION FORCE (LBS.) RETENTION FORCE (LBS.) 1 0.120 (3.05) 7-1/4 5-3/4 2 0.123 (3.12) 5-3/4 5-1/2 3 0.125 (3.18) 2-3/4 2-1/2 4 0.128 (3.25) 1-3/4 2-1/4 5 0.126 (3.20) PLATED 1-3/4 2-1/4 0.131 (3.33) Printed Board Printed board mounting hole to be 0.123 (3.12) O 0.003 for use with push-on fastener. Material: Beryllium copper, 0.000050 inch (1.25 ) gold over copper plate. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 48 Industries, Inc. SWAGED SPACERS, LOCKNUTS, AND SWAGED SPACERS WITH PUSH-ON FASTENERS ACCESSORIES SWAGED SPACER (S) 0.187 (4.75) 4-40 UNC Threads CONNECTOR SERIES A SND 0.225 (5.72) SCBM 0.250 (6.35) SDD 0.375 (9.53) Printed Board A 0.015 (0.38) Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. SWAGED SPACERS (S2) 0.187 (4.75) 4-40 UNC Threads, Typical Panel 0.125 (3.18) 0.015 (0.38) Typical Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. SWAGED LOCKNUT (S5) Polyester Insert 0.180 (4.57) 4-40 UNC Threads. 2.5 threads in metal, nominal. Panel 0.115 (2.92) 0.015 (0.38) 0.055 (1.40) Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. Polyester insert. SWAGED SPACER WITH PUSH-ON FASTENER (S6) 0.187 (4.75) 4-40 UNC Threads 0.015 (0.38) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 49 Positronic Industries, Inc. A CONNECTOR SERIES A SND 0.225 (5.72) SCBM 0.250 (6.35) SDD 0.375 (9.53) Printed board mounting hole to be 0.123 (3.12) O 0.003 for use with push-on fastener. Material: Phosphor bronze, 0.000050 inch (1.25 ) gold over copper plate. RIGHT ANGLE METAL MOUNTING BRACKETS ACCESSORIES RIGHT ANGLE METAL MOUNTING BRACKET (B3) STYLE 1 PART NO. STYLE 4535-2-0 1 4535-3-0 1 4535-5-0 3 4535-6-0 3 4535-8-0 2 4535-9-0 2 4535-62-0 2 A B C 0.324 0.484 0.244 (8.23) (12.29) (6.20) 0.380 0.594 0.303 (9.65) (15.09) (7.70) 0.554 0.739 0.244 (14.07) (18.77) (6.20) 0.604 0.800 0.303 (15.34) (20.32) (7.70) 0.405 0.522 0.246 (10.29) (13.26) (6.25) 0.455 0.572 0.303 (11.56) (14.53) (7.70) 0.614 0.731 0.334 NOTE: Sold only as part of (15,60) (18,57) (8,48) D SIZE SCBM 0.358 5, 55, 9 - 37 57 (9.09) 0.417 5, 55, 50 (10.59) 57 0.358 15 - 62 (9.09) 0.417 78 (10.59) 0.358 7, 75, 9 - 37 (9.09) 77 0.414 7, 75, 50 77 (10.52) 0.445 a connector 104assembly. (11,30) SND SDD B A 0.060 (1.52) 0.275 (6.99) A 5 STYLE 3 STYLE 2 A B B 0.030 (0.76) 5 4 4 0.063 R. (1.60) Tap 4-40 UNC-2B 0.125 O (3.18) 0.063 R. (1.60) D 42 42 4 0.107 (2.72) C 0.220 (5.59) 0.040 Thick (1.02) 0.062 (1.57) thick for Size 104 SDD Series. Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. RIGHT ANGLE METAL MOUNTING BRACKET USED WITH R2, R6, R7 AND R8RIVETED-ON BRACKET ASSEMBLIES PART NO. A B C D SIZE SCBM SND SDD 4535-2-1 0.339 (8.61) 0.456 (11.58) 0.246 (6.25) 0.358 (9.09) 9 - 37 5, 55, 57 5 4535-3-1 0.395 (10.03) 0.512 (13.00) 0.303 (7.70) 0.414 (10.52) 50 5, 55, 57 5 4535-8-1 0.420 (10.67) 0.537 (13.64) 0.246 (6.25) 0.358 (9.09) 9 - 37 7, 75, 77 42 4535-9-1 0.470 (11.94) 0.587 (14.91) 0.303 (7.70) 0.414 (10.52) 50 7, 75, 77 42 4535-34-1 0.528 (13.41) 0.645 (16.38) 0.246 (6.25) 0.358 (9.09) 15 - 62 4 4535-35-1 0.573 (14.55) 0.690 (17.53) 0.303 (7.70) 0.414 (10.52) 78 4 4535-62-1 0.614 (15.60) 0.731 (18.57) 0.334 (8.48) 0.445 (11.30) 104 4 B 0.125 O (3.18) D NOTE: Sold only as part of a connector assembly. A 0.220 (5.59) C 0.040 Thick (1.02) 0.062 (1.57) thick for Size 104 SDD Series. Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. Positronic 50 Industries, Inc. THREADED POST AND METAL HOOD ACCESSORIES THREADED POST (P) 4-40 UNC Threads CONNECTOR SERIES L SND 0.225 (5.72) SCBM 0.250 (6.35) SDD 0.375 (9.53) 0.187 (4.75) L Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. METAL HOOD (H) E D PART NO. A B C D MAX. E F G H MAX. SND15000H0G 1.531 (38.88) 0.492 (12.50) 1.312 (33.32) 0.578 (14.68) 0.713 (18.11) 0.312 (7.92) 0.750 (19.05) 1.219 (30.96) SND25000H0G 2.078 (52.78) 0.492 (12.50) 1.852 (47.04) 0.578 (14.68) 1.000 (25.40) 0.312 (7.92) 1.000 (25.40) 1.532 (38.91) SND37000H0G 2.718 (69.03) 0.492 (12.50) 2.500 (63.50) 0.578 (14.68) 1.375 (34.93) 0.312 (7.92) 1.000 (25.40) 1.532 (38.91) SND50000H0G 2.625 (66.68) 0.601 (15.27) 2.406 (61.11) 0.687 (17.45) 1.406 (35.71) 0.406 (10.31) 1.125 (28.58) 1.657 (42.09) B F 0.136 O (3.45) C H Max. G Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. A REAR GROMMETS Prevent exposure of bare wires during cable flexing. A A B B CONNECTOR VARIANTS A B CONNECTOR VARIANTS A B 9 0.630 (16.00) 0.284 (7.21) 15 0.630 (16.00) 0.284 (7.21) 15 0.960 (24.38) 0.284 (7.21) 26 0.960 (24.38) 0.284 (7.21) 25 1.504 (38.21) 0.284 (7.21) 44 1.504 (38.21) 0.284 (7.21) 37 2.146 (54.51) 0.284 (7.21) 62 2.146 (54.51) 0.284 (7.21) 50 2.054 (52.17) 0.396 (10.06) 78 2.054 (52.17) 0.396 (10.06) Material: Silicon rubber. Consult factory for ordering information. 51 0.125(3.18) Positronic Industries, Inc. Rear Grommet DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. EMI/RFI METAL HOODS ACCESSORIES EMI/RFI METAL HOOD (M) FOR SPACE APPLICATION SUBMINIATURE-D CONNECTORS Cable Opening ALUMINUM HOOD WITH ROTATING MALE OR FEMALE JACKSCREWS C A Typical Part Number: (FOR HOOD ASSEMBLY) D25000M00 B POSITRONIC INDUSTRIES Rotating Male or Female Jackscrews, 4-40 UNC Threads CABLE OPENING, MAX. PART NUMBER A B C D900000 1.397 (35.48) 1.750 (44.45) 0.630 (16.00) O 0.375 (9.53) D1500000 1.725 (43.82) 1.750 (44.45) 0.630 (16.00) O 0.375 (9.53) D2500000 2.265 (57.53) 1.750 (44.45) 0.630 (16.00) O 0.450 (11.43) D3700000 2.913 (73.99) 1.750 (44.45) 0.630 (16.00) O 0.450 (11.43) D5000000 2.819 (71.60) 1.750 (44.45) 0.740 (18.80) 0.550 O (13.97) D10400000 2.913 (73.99) 1.750 (44.45) 0.803 (20.40) O TYPICAL INSERTS Typical Part Number: (FOR CABLE ENTRY INSERT) 4595 - - - NOTE: Inserts are not supplied with hood and must be ordered separately. Consult the Factory for part number completion based upon Customer requirements. Material: Hood - Aluminum per QQ-A-225, yellow chromate conversion per MIL-C-5541 or black anodize per MIL-A-8625 optional. Hardware - Non-magnetic stainless steel per QQ-S-763, passivated per QQ-P-35, or brass per QQ-B-626 with 0.000050 (1.27) gold plate over copper per MIL-G-45204 optional. 0.625 (15.88) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. ( ) - DESIGNATES HOOD ACCESSORIES OPTION HOOD ACCESSORIES PART NUMBERS HARDWARE OPTIONS YELLOW CHROMATE CONVERSION HOOD WITH STAINLESS STEEL HARDWARE YELLOW CHROMATE CONVERSION HOOD WITH COPPER ALLOY HARDWARE BLACK ANODIZED HOOD BLACK ANODIZED HOOD WITH STAINLESS STEEL WITH COPPER ALLOY HARDWARE HARDWARE MALE ROTATING JACKSCREWS D000M00 D000MG00 D000MB00 D000MC00 FEMALE ROTATING JACKSCREWS D000M700 D000M7G00 D000M7B00 D000M7C00 ONE (1) MALE ROTATING JACKSCREW AND ONE (1) FEMALE ROTATING JACKSCREW D000M600 D000M6G00 D000M6B00 D000M6C00 ( ) - DESIGNATES CONNECTOR SIZE Positronic 52 Industries, Inc. POLARIZED AND NON-POLARIZED JACKSCREW SYSTEMS ACCESSORIES JACKSCREW SYSTEMS E T E2 0.647 (16.44) A B 0.437 (11.10) 0.250 (6.35) Rotating Male Jackscrews CODE A B T 0.437 (11.10) 0.250 (6.35) T2 0.500 (12.70) 0.198 (5.03) Rotating Male Jackscrews Fixed Female Jackscrews 4-40 UNC Threads 4-40 UNC Threads 4-40 UNC Threads FIXED FEMALE JACKSCREWS ROTATING MALE SCREW LOCKS ROTATING MALE JACKSCREWS Jackscrew Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. Material: Screw - Brass, 0.000050 inch (1.25 ) gold over copper plate. U-Clip - Brass, 0.000050 inch (1.25 ) gold over copper plate. NOTE: Stainless steel Jackscrews are available. Consult factory for ordering information. POLARIZED JACKSCREW SYSTEMS E6 T6 0.445 (11.30) 0.220 (5.59) Fixed Female Jackscrew with 4-40 UNC Threads Position 1 for Male Connector 0.655 (16.64) 0.150 (3.81) Rotating Male Jackscrew with 4-40 UNC Threads Position 1 for Female Connector Material: Brass, 0.000050 inch (1.25 ) gold over copper plate. Material: Brass, 0.000050 inch (1.25 ) gold over Position 1 for Female Connector 0.436 (11.07) Fixed Male Jackscrew with 4-40 UNC Threads 0.194 (4.93) FIXED MALE AND FEMALE JACKSCREWS 53 Positronic Industries, Inc. Rotating Female Jackscrew with 4-40 UNC Threads Position 1 for Male Connector 0.177 (4.46) 0.682 (17.32) ROTATING MALE AND FEMALE JACKSCREWS DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. IN-LINE CRIMP SPLICE AND PROTECTIVE COVER ACCESSORIES IN-LINE CRIMP SPLICE : To order crimp splice with insulating sleeve, add "-W" suffix to part number. To order without sleeve, add "-N" suffix. Consult factory for crimp tool part number. PART NUMBER WIRE SIZE AWG/(mm2) L A B PSK43636- 20-26 AWG (0.5/0.12 mm2) 0.500 (12.70) 0.045 (1.14) 0.076 (1.93) PSK43637- 16-20 AWG (1.5/0.5 mm2) 0.575 (14.61) 0.066 (1.68) 0.101 (2.57) PSK43638- 12-18 AWG (4.0-1.0 mm2) 0.577 (14.66) 0.097 (2.46) 0.150 (3.81) Materials: Splice: Copper alloy, 0.000050 (1.25 ) gold over copper. Sleeve: Shrink-fit polyvinylidene fluoride. EMI/RFI PROTECTIVE COVER O0.1200.005 (3.050.13) Two places 0.0500.010(1.270.25) 0.0360.008(0.910.20) PART NUMBER CONNECTOR A B B1 C D D1 E G H K M VARIANT SIZES 0.015 0.005 0.005 0.005 0.005 0.005 0.015 0.010 0.010 0.005 0.010 PSK633-9MG 9 M/15 M 1.213 (30.81) PSK633-9FG 9 F/15 F 1.213 0.643 (30.81) (16.33) PSK633-15MG 15 M/26 M 1.541 (39.14) PSK633-15FG 15 F/26 F 1.541 0.971 (39.14) (24.66) PSK633-25MG 25 M/44 M 2.088 (53.04) PSK633-25FG 25 F/44 F 2.088 1.511 (53.04) (38.38) PSK633-37MG 37 M/62 M 2.729 (69.32) PSK633-37FG 37 F/62 F 2.729 2.159 (69.32) (54.84) PSK633-50MG 50 M/78 M 2.635 (66.93) PSK633-50FG 50 F/78 F 2.635 2.064 (66.93) (52.43) PSK633-104MG - /104 M 2.729 (69.32) PSK633-104FG - /104 F 2.729 2.189 (69.32) (55.60) DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE. 0.666 0.984 (16.92) (24.99) 0.984 (24.99) 0.329 (8.36) 0.494 0.759 0.422 (12.55) (19.28) (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 1.083 0.422 (12.55) (27.51) (10.72) 0.233 (5.92) 0.422 (10.72) 0.494 1.083 0.422 (12.55) (27.51) (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 1.625 0.422 (12.55) (41.28) (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 1.625 0.422 (12.55) (41.28) (10.72) 0.243 (6.17) 0.429 (10.90) 0.494 2.272 0.422 (12.55) (57.71) (10.72) 0.230 (5.84) 0.426 (10.82) 0.494 2.272 0.422 (12.55) (57.71) (10.72) 0.243 (6.17) 0.429 (10.90) 0.441 0.605 2.178 0.534 (11.20) (15.37) (55.32) (13.56) 0.230 (5.84) 0.426 (10.82) 0.605 2.178 0.534 (15.37) (55.32) (13.56) 0.243 (6.17) 0.429 (10.90) 0.503 0.668 2.302 0.596 (12.78) (16.97) (58.47) (15.14) 0.230 (5.84) 0.426 (10.82) 0.668 2.302 0.596 (16.97) (58.47) (15.14) 0.243 (6.17) 0.429 (10.90) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 2.182 2.500 (55.42) (63.50) 2.500 (63.50) 0.422 (10.72) 0.329 (8.36) 1.534 1.852 (38.96) (47.04) 1.852 (47.04) 0.233 (5.92) 0.311 (7.90) 0.994 1.312 (25.25) (33.32) 1.312 (33.32) 0.494 0.759 0.422 (12.55) (19.28) (10.72) 0.329 (8.36) 0.311 (7.90) 2.079 2.406 (52.81) (61.11) 2.406 0.423 (61.11) (10.74) 2.212 2.500 (56.18) (63.50) 2.500 0.485 (63.50) (12.32) : To order protective cover with E2 rotating male screw locks (see page 53), insert "N" into the last digit of part number. Omit this digit if thread locks are not required. Material: Brass, 0.000050 (1.25 ) gold over copper. Positronic 54 Industries, Inc. GSFC CONNECTORS GSFC-311-QPLD QUALIFIED PARTS LIST DIRECTORY Positronic Industries offers the following listing of connectors and accessories, which are products qualified under GSFC Specifications GSFC-S-311-P-4 and GSFC-S-311-P-10. 55 GSFC PART NUMBER POSITRONIC PART NUMBER 311P10-1P-B-12 311P10-1P-B-15 311P10-1S-B-12 311P10-1S-B-15 SND9M2000G-1082.24 SND9M20200G-1082.24 SND9F2000G-1082.24 SND9F20200G-1082.24 311P10-17P-B-12 311P10-17P-B-15 311P10-17S-B-12 311P10-17S-B-15 SCBM17W5M2000G-1082.24 SCBM17W5M20200G-1082.24 SCBM17W5F2000G-1082.24 SCBM17W5F20200G-1082.24 311P10-9P-C-12 311P10-9P-C-15 311P10-9S-C-12 311P10-9S-C-15 SCBM11W1M2000G-1082.24 SCBM11W1M20200G-1082.24 SCBM11W1F2000G-1082.24 SCBM11W1F20200G-1082.24 311P10-2P-B-12 311P10-2P-B-15 311P10-2S-B-12 311P10-2S-B-15 SND15M2000G-1082.24 SND15M20200G-1082.24 SND15F2000G-1082.24 SND15F20200G-1082.24 311P10-18P-B-12 311P10-18P-B-15 311P10-18S-B-12 311P10-18S-B-15 SCBM21WA4M2000G-1082.24 SCBM21WA4M20200G-1082.24 SCBM21WA4F2000G-1082.24 SCBM21WA4F20200G-1082.24 311P10-10P-C-12 311P10-10P-C-15 311P10-10S-C-12 311P10-10S-C-15 SCBM5W5M0000G-1082.24 SCBM5W5M00200G-1082.24 SCBM5W5F0000G-1082.24 SCBM5W5F00200G-1082.24 311P10-3P-B-12 311P10-3P-B-15 311P10-3S-B-12 311P10-3S-B-15 SND25M2000G-1082.24 SND25M20200G-1082.24 SND25F2000G-1082.24 SND25F20200G-1082.24 311P10-20P-B-12 311P10-20P-B-15 311P10-20S-B-12 311P10-20S-B-15 SCBM25W3M2000G-1082.24 SCBM25W3M20200G-1082.24 SCBM25W3F2000G-1082.24 SCBM25W3F20200G-1082.24 311P10-11P-C-12 311P10-11P-C-15 311P10-11S-C-12 311P10-11S-C-15 SCBM9W4M2000G-1082.24 SCBM9W4M20200G-1082.24 SCBM9W4F2000G-1082.24 SCBM9W4F20200G-1082.24 311P10-4P-B-12 311P10-4P-B-15 311P10-4S-B-12 311P10-4S-B-15 SND37M2000G-1082.24 SND37M20200G-1082.24 SND37F2000G-1082.24 SND37F20200G-1082.24 311P10-21P-B-12 311P10-21P-B-15 311P10-21S-B-12 311P10-21S-B-15 SCBM27W2M2000G-1082.24 SCBM27W2M20200G-1082.24 SCBM27W2F2000G-1082.24 SCBM27W2F20200G-1082.24 311P10-12P-C-12 311P10-12P-C-15 311P10-12S-C-12 311P10-12S-C-15 SCBM13W3M2000G-1082.24 SCBM13W3M20200G-1082.24 SCBM13W3F2000G-1082.24 SCBM13W3F20200G-1082.24 311P10-5P-B-12 311P10-5P-B-15 311P10-5S-B-12 311P10-5S-B-15 SND50M2000G-1082.24 SND50M20200G-1082.24 SND50F2000G-1082.24 SND50F20200G-1082.24 311P10-22P-B-12 311P10-22P-B-15 311P10-22S-B-12 311P10-22S-B-15 SCBM24W7M2000G-1082.24 SCBM24W7M20200G-1082.24 SCBM24W7F2000G-1082.24 SCBM24W7F20200G-1082.24 311P10-13P-C-12 311P10-13P-C-15 311P10-13S-C-12 311P10-13S-C-15 SCBM17W2M2000G-1082.24 SCBM17W2M20200G-1082.24 SCBM17W2F2000G-1082.24 SCBM17W2F20200G-1082.24 311P10-6P-B-12 311P10-6P-B-15 311P10-6S-B-12 311P10-6S-B-15 SCBM5W1M2000G-1082.24 SCBM5W1M20200G-1082.24 SCBM5W1F2000G-1082.24 SCBM5W1F20200G-1082.24 311P10-23P-B-12 311P10-23P-B-15 311P10-23S-B-12 311P10-23S-B-15 SCBM36W4M2000G-1082.24 SCBM36W4M20200G-1082.24 SCBM36W4F2000G-1082.24 SCBM36W4F20200G-1082.24 311P10-14P-C-12 311P10-14P-C-15 311P10-14S-C-12 311P10-14S-C-15 SCBM21W1M2000G-1082.24 SCBM21W1M20200G-1082.24 SCBM21W1F2000G-1082.24 SCBM21W1F20200G-1082.24 311P10-7P-B-12 311P10-7P-B-15 311P10-7S-B-12 311P10-7S-B-15 SCBM3W3M0000G-1082.24 SCBM3W3M00200G-1082.24 SCBM3W3F0000G-1082.24 SCBM3W3F00200G-1082.24 311P10-24P-B-12 311P10-24P-B-15 311P10-24S-B-12 311P10-24S-B-15 SCBM43W2M2000G-1082.24 SCBM43W2M20200G-1082.24 SCBM43W2F2000G-1082.24 SCBM43W2F20200G-1082.24 311P10-15P-C-12 311P10-15P-C-15 311P10-15S-C-12 311P10-15S-C-15 SCBM8W8M0000G-1082.24 SCBM8W8M00200G-1082.24 SCBM8W8F0000G-1082.24 SCBM8W8F00200G-1082.24 311P10-8P-B-12 311P10-8P-B-15 311P10-8S-B-12 311P10-8S-B-15 SCBM7W2M2000G-1082.24 SCBM7W2M20200G-1082.24 SCBM7W2F2000G-1082.24 SCBM7W2F20200G-1082.24 311P10-25P-B-12 311P10-25P-B-15 311P10-25S-B-12 311P10-25S-B-15 SCBM47W1M2000G-1082.24 SCBM47W1M20200G-1082.24 SCBM47W1F2000G-1082.24 SCBM47W1F20200G-1082.24 311P10-16P-C-12 311P10-16P-C-15 311P10-16S-C-12 311P10-16S-C-15 SCBM13W6M2000G-1082.24 SCBM13W6M20200G-1082.24 SCBM13W6F2000G-1082.24 SCBM13W6F20200G-1082.24 311P10-9P-B-12 311P10-9P-B-15 311P10-9S-B-12 311P10-9S-B-15 SCBM11W1M2000G-1082.24 SCBM11W1M20200G-1082.24 SCBM11W1F2000G-1082.24 SCBM11W1F20200G-1082.24 311P10-1P-C-12 311P10-1P-C-15 311P10-1S-C-12 311P10-1S-C-15 SND9M2000G-1082.24 SND9M20200G-1082.24 SND9F2000G-1082.24 SND9F20200G-1082.24 311P10-17P-C-12 311P10-17P-C-15 311P10-17S-C-12 311P10-17S-C-15 SCBM17W5M2000G-1082.24 SCBM17W5M20200G-1082.24 SCBM17W5F2000G-1082.24 SCBM17W5F20200G-1082.24 311P10-10P-B-12 311P10-10P-B-15 311P10-10S-B-12 311P10-10S-B-15 SCBM5W5M0000G-1082.24 SCBM5W5M00200G-1082.24 SCBM5W5F0000G-1082.24 SCBM5W5F00200G-1082.24 311P10-2P-C-12 311P10-2P-C-15 311P10-2S-C-12 311P10-2S-C-15 SND15M2000G-1082.24 SND15M20200G-1082.24 SND15F2000G-1082.24 SND15F20200G-1082.24 311P10-18P-C-12 311P10-18P-C-15 311P10-18S-C-12 311P10-18S-C-15 SCBM21WA4M2000G-1082.24 SCBM21WA4M20200G-1082.24 SCBM21WA4F2000G-1082.24 SCBM21WA4F20200G-1082.24 311P10-11P-B-12 311P10-11P-B-15 311P10-11S-B-12 311P10-11S-B-15 SCBM9W4M2000G-1082.24 SCBM9W4M20200G-1082.24 SCBM9W4F2000G-1082.24 SCBM9W4F20200G-1082.24 311P10-3P-C-12 311P10-3P-C-15 311P10-3S-C-12 311P10-3S-C-15 SND25M2000G-1082.24 SND25M20200G-1082.24 SND25F2000G-1082.24 SND25F20200G-1082.24 311P10-20P-C-12 311P10-20P-C-15 311P10-20S-C-12 311P10-20S-C-15 SCBM25W3M2000G-1082.24 SCBM25W3M20200G-1082.24 SCBM25W3F2000G-1082.24 SCBM25W3F20200G-1082.24 311P10-12P-B-12 311P10-12P-B-15 311P10-12S-B-12 311P10-12S-B-15 SCBM13W3M2000G-1082.24 SCBM13W3M20200G-1082.24 SCBM13W3F2000G-1082.24 SCBM13W3F20200G-1082.24 311P10-4P-C-12 311P10-4P-C-15 311P10-4S-C-12 311P10-4S-C-15 SND37M2000G-1082.24 SND37M20200G-1082.24 SND37F2000G-1082.24 SND37F20200G-1082.24 311P10-21P-C-12 311P10-21P-C-15 311P10-21S-C-12 311P10-21S-C-15 SCBM27W2M2000G-1082.24 SCBM27W2M20200G-1082.24 SCBM27W2F2000G-1082.24 SCBM27W2F20200G-1082.24 311P10-13P-B-12 311P10-13P-B-15 311P10-13S-B-12 311P10-13S-B-15 SCBM17W2M2000G-1082.24 SCBM17W2M20200G-1082.24 SCBM17W2F2000G-1082.24 SCBM17W2F20200G-1082.24 311P10-5P-C-12 311P10-5P-C-15 311P10-5S-C-12 311P10-5S-C-15 SND50M2000G-1082.24 SND50M20200G-1082.24 SND50F2000G-1082.24 SND50F20200G-1082.24 311P10-22P-C-12 311P10-22P-C-15 311P10-22S-C-12 311P10-22S-C-15 SCBM24W7M2000G-1082.24 SCBM24W7M20200G-1082.24 SCBM24W7F2000G-1082.24 SCBM24W7F20200G-1082.24 311P10-14P-B-12 311P10-14P-B-15 311P10-14S-B-12 311P10-14S-B-15 SCBM21W1M2000G-1082.24 SCBM21W1M20200G-1082.24 SCBM21W1F2000G-1082.24 SCBM21W1F20200G-1082.24 311P10-6P-C-12 311P10-6P-C-15 311P10-6S-C-12 311P10-6S-C-15 SCBM5W1M2000G-1082.24 SCBM5W1M20200G-1082.24 SCBM5W1F2000G-1082.24 SCBM5W1F20200G-1082.24 311P10-23P-C-12 311P10-23P-C-15 311P10-23S-C-12 311P10-23S-C-15 SCBM36W4M2000G-1082.24 SCBM36W4M20200G-1082.24 SCBM36W4F2000G-1082.24 SCBM36W4F20200G-1082.24 311P10-15P-B-12 311P10-15P-B-15 311P10-15S-B-12 311P10-15S-B-15 SCBM8W8M0000G-1082.24 SCBM8W8M00200G-1082.24 SCBM8W8F0000G-1082.24 SCBM8W8F00200G-1082.24 311P10-7P-C-12 311P10-7P-C-15 311P10-7S-C-12 311P10-7S-C-15 SCBM3W3M0000G-1082.24 SCBM3W3M00200G-1082.24 SCBM3W3F0000G-1082.24 SCBM3W3F00200G-1082.24 311P10-24P-C-12 311P10-24P-C-15 311P10-24S-C-12 311P10-24S-C-15 SCBM43W2M2000G-1082.24 SCBM43W2M20200G-1082.24 SCBM43W2F2000G-1082.24 SCBM43W2F20200G-1082.24 311P10-16P-B-12 311P10-16P-B-15 311P10-16S-B-12 311P10-16S-B-15 SCBM13W6M2000G-1082.24 SCBM13W6M20200G-1082.24 SCBM13W6F2000G-1082.24 SCBM13W6F20200G-1082.24 311P10-8P-C-12 311P10-8P-C-15 311P10-8S-C-12 311P10-8S-C-15 SCBM7W2M2000G-1082.24 SCBM7W2M20200G-1082.24 SCBM7W2F2000G-1082.24 SCBM7W2F20200G-1082.24 311P10-25P-C-12 311P10-25P-C-15 311P10-25S-C-12 311P10-25S-C-15 SCBM47W1M2000G-1082.24 SCBM47W1M20200G-1082.24 SCBM47W1F2000G-1082.24 SCBM47W1F20200G-1082.24 Positronic Industries, Inc. GSFC PART NUMBER POSITRONIC PART NUMBER GSFC PART NUMBER POSITRONIC PART NUMBER GSFC-311-QPLD QUALIFIED PARTS LIST DIRECTORY GSFC CONNECTORS Positronic Industries offers the following listing of connectors and accessories, which are products qualified under GSFC Specifications GSFC-S-311-P-4 and GSFC-S-311-P-10. NOTE: Items denoted by * are undergoing qualification. Consult factory for availability of items denoted by **. GSFC PART NUMBER POSITRONIC PART NUMBER GSFC PART NUMBER POSITRONIC PART NUMBER GSFC PART NUMBER POSITRONIC PART NUMBER 311P405-6P-B-12 311P405-6P-B-15 311P405-6S-B-12 311P405-6S-B-15 SCBC5W1M0000G-1082.24 SCBC5W1M00200G-1082.24 SCBC5W1F0000G-1082.24 SCBC5W1F00200G-1082.24 **311P405-21P-B-12 **311P405-21P-B-15 **311P405-21S-B-12 **311P405-21S-B-15 SCBC27W2M0000G-1082.24 SCBC27W2M00200G-1082.24 SCBC27W2F0000G-1082.24 SCBC27W2F00200G-1082.24 311P409-4P-B-12 311P409-4P-B-15 311P409-4S-B-12 311P409-4S-B-15 SND37M0000G-1082.24 SND37M00200G-1082.24 SND37F0000G-1082.24 SND37F00200G-1082.24 311P405-7P-B-12 311P405-7P-B-15 311P405-7S-B-12 311P405-7S-B-15 SCBM3W3M0000G-1082.24 SCBM3W3M00200G-1082.24 SCBM3W3F0000G-1082.24 SCBM3W3F00200G-1082.24 **311P405-22P-B-12 **311P405-22P-B-15 311P405-22S-B-12 311P405-22S-B-15 SCBC24W7M0000G-1082.24 SCBC24W7M00200G-1082.24 SCBC24W7F0000G-1082.24 SCBC24W7F00200G-1082.24 311P409-5P-B-12 311P409-5P-B-15 311P409-5S-B-12 311P409-5S-B-15 SND50M0000G-1082.24 SND50M00200G-1082.24 SND50F0000G-1082.24 SND50F00200G-1082.24 311P405-8P-B-12 311P405-8P-B-15 311P405-8S-B-12 311P405-8S-B-15 SCBC7W2M0000G-1082.24 SCBC7W2M00200G-1082.24 SCBC7W2F0000G-1082.24 SCBC7W2F00200G-1082.24 311P405-23P-B-12 311P405-23P-B-15 311P405-23S-B-12 311P405-23S-B-15 SCBC36W4M0000G-1082.24 SCBC36W4M00200G-1082.24 SCBC36W4F0000G-1082.24 SCBC36W4F00200G-1082.24 G08P1 G08S1 G10P1 G10S1 MC8022D-50-1202.4 FC8022D-50-1202.4 MC6020D-50-1202.4 FC6020D-50-1202.4 311P405-9P-B-12 311P405-9P-B-15 311P405-9S-B-12 311P405-9S-B-15 SCBC11W1M0000G-1082.24 SCBC11W1M00200G-1082.24 SCBC11W1F0000G-1082.24 SCBC11W1F00200G-1082.24 311P405-24P-B-12 311P405-24P-B-15 311P405-24S-B-12 311P405-24S-B-15 SCBC43W2M0000G-1082.24 SCBC43W2M00200G-1082.24 SCBC43W2F0000G-1082.24 SCBC43W2F00200G-1082.24 *GCP1 *GCP2 *GCP3 *GCP4 MC4101M MC4102M MC4103M MC4104M 311P405-10P-B-12 311P405-10P-B-15 311P405-10S-B-12 311P405-10S-B-15 SCBM5W5M0000G-1082.24 SCBM5W5M00200G-1082.24 SCBM5W5F0000G-1082.24 SCBM5W5F00200G-1082.24 311P405-25P-B-12 311P405-25P-B-15 311P405-25S-B-12 311P405-25S-B-15 SCBC47W1M0000G-1082.24 SCBC47W1M00200G-1082.24 SCBC47W1F0000G-1082.24 SCBC47W1F00200G-1082.24 *GCRP1 *GCRP2 *GCRP3 *GCRP4 MC4201M MC4202M MC4203M MC4204M **311P405-11P-B-12 **311P405-11P-B-15 **311P405-11S-B-12 **311P405-11S-B-15 SCBC9W4M0000G-1082.24 SCBC9W4M00200G-1082.24 SCBC9W4F0000G-1082.24 SCBC9W4F00200G-1082.24 311P407-1P-B-12 311P407-1P-B-15 311P407-1S-B-12 311P407-1S-B-15 SDD15M0000G-1082.24 SDD15M00200G-1082.24 SDD15F0000G-1082.24 SDD15F00200G-1082.24 *GCS1 *GCS2 *GCS3 *GCS4 FC4101M FC4102M FC4103M FC4104M 311P405-12P-B-12 311P405-12P-B-15 311P405-12S-B-12 311P405-12S-B-15 SCBC13W3M0000G-1082.24 SCBC13W3M00200G-1082.24 SCBC13W3F0000G-1082.24 SCBC13W3F00200G-1082.24 311P407-2P-B-12 311P407-2P-B-15 311P407-2S-B-12 311P407-2S-B-15 SDD26M0000G-1082.24 SDD26M00200G-1082.24 SDD26F0000G-1082.24 SDD26F00200G-1082.24 *GCRS1 *GCRS2 *GCRS3 *GCRS4 FC4201M FC4202M FC4203M FC4204M 311P405-13P-B-12 311P405-13P-B-15 311P405-13S-B-12 311P405-13S-B-15 SCBC17W2M0000G-1082.24 SCBC17W2M00200G-1082.24 SCBC17W2F0000G-1082.24 SCBC17W2F00200G-1082.24 311P407-3P-B-12 311P407-3P-B-15 311P407-3S-B-12 311P407-3S-B-15 SDD44M0000G-1082.24 SDD44M00200G-1082.24 SDD44F0000G-1082.24 SDD44F00200G-1082.24 *GHP6 *GHS6 MS4820M FS4820M *GHRP6 *GHRS6 MS4920M FS4920M 311P405-14P-B-12 311P405-14P-B-15 311P405-14S-B-12 311P405-14S-B-15 SCBC21W1M0000G-1082.24 SCBC21W1M00200G-1082.24 SCBC21W1F0000G-1082.24 SCBC21W1F00200G-1082.24 311P407-4P-B-12 311P407-4P-B-15 311P407-4S-B-12 311P407-4S-B-15 SDD62M0000G-1082.24 SDD62M00200G-1082.24 SDD62F0000G-1082.24 SDD62F00200G-1082.24 311P405-15P-B-12 311P405-15P-B-15 311P405-15S-B-12 311P405-15S-B-15 SCBM8W8M0000G-1082.24 SCBM8W8M00200G-1082.24 SCBM8W8F0000G-1082.24 SCBM8W8F00200G-1082.24 311P407-5P-B-12 311P407-5P-B-15 311P407-5S-B-12 311P407-5S-B-15 SDD78M0000G-1082.24 SDD78M00200G-1082.24 SDD78F0000G-1082.24 SDD78F00200G-1082.24 **311P405-16P-B-12 **311P405-16P-B-15 **311P405-16S-B-12 **311P405-16S-B-15 SCBC13W6M0000G-1082.24 SCBC13W6M00200G-1082.24 SCBC13W6F0000G-1082.24 SCBC13W6F00200G-1082.24 311P407-6P-B-12 311P407-6P-B-15 311P407-6S-B-12 311P407-6S-B-15 SDD104M0000G-1082.24 SDD104M00200G-1082.24 SDD104F0000G-1082.24 SDD104F00200G-1082.24 **311P405-17P-B-12 **311P405-17P-B-15 **311P405-17S-B-12 **311P405-17S-B-15 SCBC17W5M0000G-1082.24 SCBC17W5M00200G-1082.24 SCBC17W5F0000G-1082.24 SCBC17W5F00200G-1082.24 311P409-1P-B-12 311P409-1P-B-15 311P409-1S-B-12 311P409-1S-B-15 SND9M0000G-1082.24 SND9M00200G-1082.24 SND9F0000G-1082.24 SND9F00200G-1082.24 311P405-18P-B-12 311P405-18P-B-15 311P405-18S-B-12 311P405-18S-B-15 SCBC21WA4M0000G-1082.24 SCBC21WA4M00200G-1082.24 SCBC21WA4F0000G-1082.24 SCBC21WA4F00200G-1082.24 311P409-2P-B-12 311P409-2P-B-15 311P409-2S-B-12 311P409-2S-B-15 SND15M0000G-1082.24 SND15M00200G-1082.24 SND15F0000G-1082.24 SND15F00200G-1082.24 311P405-20P-B-12 311P405-20P-B-15 311P405-20S-B-12 311P405-20S-B-15 SCBC25W3M0000G-1082.24 SCBC25W3M00200G-1082.24 SCBC25W3F0000G-1082.24 SCBC25W3F00200G-1082.24 311P409-3P-B-12 311P409-3P-B-15 311P409-3S-B-12 311P409-3S-B-15 SND25M0000G-1082.24 SND25M00200G-1082.24 SND25F0000G-1082.24 SND25F00200G-1082.24 Positronic 56 Industries, Inc. QPL CONNECTORS MIL-DTL-24308/MIL-C-39029/MIL-C-85049 QUALIFIED PARTS LIST DIRECTORY Positronic HDM Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number 24308-618-79/24308-1210-85. Positronic RD Series Hoods are Q.P.L. approved to MIL-C-85049 per test report number 85049-870-84. Positronic DD Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number 24308-1209-85/24308-1210-85/24308-117-89. Positronic RD Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number 24308-211-79/24308-1210-85. Positronic RD Series Contacts are Q.P.L. approved to MIL-C-39029 per test report number 39029-694-79. MILITARY PART NUMBER 57 POSITRONIC PART NUMBER MILITARY PART NUMBER POSITRONIC PART NUMBER MILITARY PART NUMBER POSITRONIC PART NUMBER M24308/5-34 M24308/5-35 M24308/5-36 M24308/5-37 HDM9F20000-403.3 HDM15F20000-403.3 HDM25F20000-403.3 HDM37F20000-403.3 M24308/6-564 M24308/6-565 M24308/6-566 M24308/6-567 RD25F11F000-403.6 RD37F11F000-403.6 RD50F11F000-403.6 DD15F11F000-403.6 M24308/8-361 M24308/8-362 M24308/8-363 M24308/8-364 RD50M00000-403.3 DD15M00000-403.3 DD26M00000-403.3 DD44M00000-403.3 M24308/5-38 M24308/5-56 M24308/5-57 M24308/5-58 HDM50F20000-403.3 HDM9F2F000-403.4 HDM15F2F000-403.4 HDM25F2F000-403.4 M24308/6-568 M24308/6-569 M24308/6-570 M24308/6-571 DD26F11F000-403.6 DD44F11F000-403.6 DD62F11F000-403.6 DD78F11F000-403.6 M24308/8-365 M24308/8-366 M24308/8-367 M24308/8-401 DD62M00000-403.3 DD78M00000-403.3 DD104M00000-403.3 RD9M11F000-403.4 M24308/5-59 M24308/5-60 M24308/6-502 M24308/6-503 HDM37F2F000-403.4 HDM50F2F000-403.4 RD9F110000-50-403.3 RD15F110000-50-403.3 M24308/6-572 M24308/6-573 M24308/6-574 M24308/6-575 DD104F11F000-403.6 RD9F0F000-403.4 RD15F0F000-403.4 RD25F0F000-403.4 M24308/8-402 M24308/8-403 M24308/8-404 M24308/8-405 RD15M11F000-403.4 RD25M11F000-403.4 RD37M11F000-403.4 RD50M11F000-403.4 M24308/6-504 M24308/6-505 M24308/6-506 M24308/6-507 RD25F110000-50-403.3 RD37F110000-50-403.3 RD50F110000-50-403.3 RD9F110000-50-403.5 M24308/6-576 M24308/6-577 M24308/6-578 M24308/6-579 RD37F0F000-403.4 RD50F0F000-403.4 DD15F0F000-403.4 DD26F0F000-403.4 M24308/8-406 M24308/8-407 M24308/8-408 M24308/8-409 DD15M11F000-403.4 DD26M11F000-403.4 DD44M11F000-403.4 DD62M11F000-403.4 M24308/6-508 M24308/6-509 M24308/6-510 M24308/6-511 RD15F110000-50-403.5 RD25F110000-50-403.5 RD37F110000-50-403.5 RD50F110000-50-403.5 M24308/6-580 M24308/6-581 M24308/6-582 M24308/6-583 DD44F0F000-403.4 DD62F0F000-403.4 DD78F0F000-403.4 DD104F0F000-403.4 M24308/8-410 M24308/8-411 M24308/8-412 M24308/8-413 DD78M11F000-403.4 DD104M11F000-403.4 RD9M11F000-403.6 RD15M11F000-403.6 M24308/6-512 M24308/6-513 M24308/6-514 M24308/6-515 DD15F110000-50-403.3 DD26F110000-50-403.3 DD44F110000-50-403.3 DD62F110000-50-403.3 M24308/7-23 M24308/7-24 M24308/7-25 M24308/7-26 HDM9M20000-403.3 HDM15M20000-403.3 HDM25M20000-403.3 HDM37M20000-403.3 M24308/8-414 M24308/8-415 M24308/8-416 M24308/8-417 RD25M11F000-403.6 RD37M11F000-403.6 RD50M11F000-403.6 DD15M11F000-403.6 M24308/6-516 M24308/6-517 M24308/6-518 M24308/6-519 DD78F110000-50-403.3 DD104F110000-50-403.3 DD15F110000-50-403.5 DD26F110000-50-403.5 M24308/7-27 M24308/7-34 M24308/7-35 M24308/7-36 HDM50M20000-403.3 HDM9M2F000-403.4 HDM15M2F000-403.4 HDM25M2F000-403.4 M24308/8-418 M24308/8-419 M24308/8-420 M24308/8-421 DD26M11F000-403.6 DD44M11F000-403.6 DD62M11F000-403.6 DD78M11F000-403.6 M24308/6-520 M24308/6-521 M24308/6-522 M24308/6-523 DD44F110000-50-403.5 DD62F110000-50-403.5 DD78F110000-50-403.5 DD104F110000-50-403.5 M24308/7-37 M24308/7-38 M24308/8-335 M24308/8-336 HDM37M2F000-403.4 HDM50M2F000-403.4 RD9M110000-403.3 RD15M110000-403.3 M24308/8-422 M24308/8-423 M24308/8-424 M24308/8-425 DD104M11F000-403.6 RD9M0F000-403.4 RD15M0F000-403.4 RD25M0F000-403.4 M24308/6-540 M24308/6-541 M24308/6-542 M24308/6-543 RD9F00000-403.3 RD15F00000-403.3 RD25F00000-403.3 RD37F00000-403.3 M24308/8-337 M24308/8-338 M24308/8-339 M24308/8-340 RD25M110000-403.3 RD37M110000-403.3 RD50M110000-403.3 RD9M110000-403.5 M24308/8-426 M24308/8-427 M24308/8-428 M24308/8-429 RD37M0F000-403.4 RD50M0F000-403.4 DD15M0F000-403.4 DD26M0F000-403.4 M24308/6-544 M24308/6-545 M24308/6-546 M24308/6-547 RD50F00000-403.3 DD15F00000-403.3 DD26F00000-403.3 DD44F00000-403.3 M24308/8-341 M24308/8-342 M24308/8-343 M24308/8-344 RD15M110000-403.5 RD25M110000-403.5 RD37M110000-403.5 RD50M110000-403.5 M24308/8-430 M24308/8-431 M24308/8-432 M24308/8-433 DD44M0F000-403.4 DD62M0F000-403.4 DD78M0F000-403.4 DD104M0F000-403.4 M24308/6-548 M24308/6-549 M24308/6-550 M24308/6-551 DD62F00000-403.3 DD78F00000-403.3 DD104F00000-403.3 RD9F11F000-50-403.4 M24308/8-345 M24308/8-346 M24308/8-347 M24308/8-348 DD15M110000-403.3 DD26M110000-403.3 DD44M110000-403.3 DD62M110000-403.3 M39029/57-354 M39029/58-360 M39029/63-368 M39029/64-369 FC8522D-50 MC8522D-50 FC5020D-50 MC5020D-50 M24308/6-552 M24308/6-553 M24308/6-554 M24308/6-555 RD15F11F000-50-403.4 RD25F11F000-50-403.4 RD37F11F000-50-403.4 RD50F11F000-50-403.4 M24308/8-349 M24308/8-350 M24308/8-351 M24308/8-352 DD78M110000-403.3 DD104M110000-403.3 DD15M110000-403.5 DD26M110000-403.5 M24308/6-556 M24308/6-557 M24308/6-558 M24308/6-559 DD15F11F000-50-403.4 DD26F11F000-50-403.4 DD44F11F000-50-403.4 DD62F11F000-50-403.4 M24308/8-353 M24308/8-354 M24308/8-355 M24308/8-356 DD44M110000-403.5 DD62M110000-403.5 DD78M110000-403.5 DD104M110000-403.5 M24308/6-560 M24308/6-561 M24308/6-562 M24308/6-563 DD78F11F000-50-403.4 DD104F11F000-50-403.4 RD9F11F000-403.6 RD15F11F000-403.6 M24308/8-357 M24308/8-358 M24308/8-359 M24308/8-360 RD9M00000-403.3 RD15M00000-403.3 RD25M00000-403.3 RD37M00000-403.3 Positronic Industries, Inc. Positronic Hermetic Connector Assemblies * Leakage Rate: <10-9 mbar.l/s * Shock and vibration resistant * Application Specific Design Positronic Industries can supply hermetic connector assemblies for use in vacuum applications. All Positronic hermetic connectors are designed to act as feedthroughs through the bulkhead/chamber wall. Typically both sides of the connector have mating faces, but certain contact terminations are also available per customer requirement. Typical configurations include: * Standard Density D-Subminiature (Contact size 20) * High Density D-Subminiature (Contact size 22) * Mixed Density D-Subminiature (Contact sizes 8 and 20 in a single package) * Circular (Variety of contact sizes and configurations) In addition to simply providing the hermetic connector itself, Positronic can provide a fully-assembled flange/plate according to customer specification (see above). For more information on Positronic hermetic capabilities, please call (800) 641-4054 and request to speak to someone about the Positronic hermetic product line. NORTH AMERICAN HEADQUARTERS UNITED STATES, Springfield, Missouri Factory Sales and Engineering Offices (800)641-4054 Factory Sales and Engineering Offices (787)841-0920 Factory Sales and Engineering Offices (800)872-7674 Factory Sales and Engineering Offices (800)327-8272 PUERTO RICO, Ponce Factory MEXICO CANADA PACIFIC BASIN HEADQUARTERS SINGAPORE, Asian Factory Factory Sales and Engineering Offices 65-6842-1419 Malaysia Sales Office 65-6842-1419 Taiwan Sales Office 8862-2937-8775 China (Shanghai) Sales Office 8621-6308-3640 Japan Sales Office 8135-661-3047 *Additional Technical Agents in Australia, New Zealand, India South Korea,Thailand, Philippines, Hong Kong and Indonesia. EUROPEAN HEADQUARTERS FRANCE, Auch Factory Factory Sales and Engineering Offices 33 5 62 63 44 91 Northern France Sales Office Southern France Sales Office Italy Sales Office Germany Sales Office 33 33 39 49 EUROPE, Direct Sales Offices EUROPE, Technical Agents 1 45 88 13 88 4 67 72 80 28 2 54 116 106 2351 63 47 39 Technical Agents in Austria, Benelux, Denmark, Finland, Greece, Ireland, Scotland, Slovenia, Spain, Sweden, Switzerland and the United Kingdom MIDEAST, Technical Agents Technical Agents in Israel and Turkey POSITRONIC INDUSTRIES, INC. 423 N Campbell Ave * PO Box 8247 * Springfield, MO 65801 Tel (417) 866-2322 * Fax (417) 866-4115 * Toll Free (800) 641-4054 info@connectpositronic.com POSITRONIC INDUSTRIES, S.A.S. Zone Industrielle d'Engachies * 46 Route d'Engachies * F-32020 Auch Cedex 9 * France Telephone 05 62 63 44 91 * Telecopieur 05 62 63 51 17 contact@connectpositronic.com POSITRONIC ASIA PTE LTD. 3014A Ubi Road 1 #06-07 * Singapore 408703 Telephone (65) 6842-1419 * Fax (65) 6842-1421 singapore@connectpositronic.com www.connectpositronic.com