Positronic Industries
Space application
Subminiature-D Connectors
GSFC S-311-P-4
GSFC S-311-P-10
MIL-DTL-24308
Unless otherwise specified, dimensional tolerances are:
1) ±0.001 inches (0.03 mm) for male contact mating diameters.
2) ±0.003 inches (0.08 mm) for contact termination diameters.
3) ±0.005 inches (0.13 mm) for all other diameters.
4) ±0.015 inches (0.38 mm) for all other dimensions.
Positronic Industries’ FEDERAL SUPPLY CODE FOR MANUFACTURERS is Number 28198.
PUBLISHED IN THE UNITED STATES OF AMERICA
Positronic Industries, Inc. believes the data contained herein to be reliable. Since the technical information is given
free of charge, the User employs such information at his own discretion and risk. Positronic Industries, Inc. assumes
no responsibility for results obtained or damages incurred from use of such information in whole or in part.
Maximum Torque Values for 4-40 UNC Threads
These torque values are applicable for threads only and do not apply to hardware assemblies. These torque
values are approximate and should not be accepted as accurate limits. Indeterminant factors in specific appli-
cations preclude the publication of accurate torque values for universal use.
MATERIAL Nm in-lb in-oz
Phos. Bronze 0.90 8.0 128
Brass 0.68 6.0 96
Aluminum 0.45 4.0 64
Nylon 0.11 1.0 16
TORQUE
CATALOG NUMBER:
C-005 REV. NC
This catalog should be accompanied by a copy of Positronic Industries’
Subminiature-D Connector and Cable Accessory Catalog.
Additional special application Subminiature-D Connector catalogs
are available upon request. Contact our Factory Sales Office or
your District Sales Manager for copies of these catalogs:
INDUSTRIAL & MILITARY APPLICATION
SUBMINIATURE-D CONNECTORS ENVIRONMENTAL-D CONNECTORS
COMBO-D CONNECTORS DUAL-PORT CONNECTORS
FILTER-D CONNECTORS
TABLE OF CONTENTS
SPACE NORMAL DENSITY
SUBMINIATURE-D CONNECTORS ......................1 - 7
SND Series. Removable or fixed contacts, 7.5
ampere nominal rating. Crimp, solder and straight
and 90˚ printed board mount contact terminations.
Five connector variants, 9 through 50 contacts.
Military quality connectors compatible with MIL-DTL-
24308, conforming to GSFC-S-311-P-4 and GSFC-
S-311-P-10 where applicable.
SPACE DENSI-D
SUBMINIATURE-D CONNECTORS .....................8 - 16
SCBM SERIES . . . . . . . . . . . . . . . . . . . . . .17 - 35
SPACE COMBINATION CONTACT
SUBMINIATURE-D CONNECTORS ....................17 - 43
SPACE APPLICATION SUBMINIATURE-D
CONNECTOR SAVERS .......................................44 - 47
QUALIFIED PARTS LIST DIRECTORY
PER GSFC-311-QPLD .........................................55 - 57
SDD Series. Removable or fixed contacts, 5 ampere
nominal rating. Crimp and straight and 90˚ printed
board contact terminations. Six connector variants,
15 through 104 contacts. Military quality connectors
compatible with MIL-DTL-24308, conforming to
GSFC-S-311-P-4 where applicable.
Fixed signal contacts, Size 20, 7.5 ampere nominal
rating. Size 8 shielded and power contacts. Solder
cup and printed board mount contact terminations
available on both Size 20 and Size 8 contacts.
Twenty connector variants, 5W1 through 46W4,
using shell sizes 1 through 6. Military quality con-
nectors compatible with MIL-DTL-24308, conforming
to GSFC-S-311-P-4 and GSFC-S-311-P-10 where
applicable.
SCBC SERIES . . . . . . . . . . . . . . . . . . . . . .32 - 43
Size 20 signal and Size 8 shielded and power remov-
able contacts. Eleven connector variants, shell sizes 1
through 6. Military quality connectors compatible with
MIL-DTL-24308, conforming to GSFC-S-311-P-4 where
applicable.
SAD, SADD and SACBM Series connector savers.
Normal density, 9 through 50 contacts. High density, 15
through 104 contacts. Combination size 20 contact/
Size 8 contact connectors using shell sizes 1 through 6.
SIZE 8 REMOVABLE CONTACTS . . . . . . . . . . . .27 - 34
Shielded and high voltage and power crimp
and solder terminations. Functional in SCBM
and SCBC connector bodies.
ACCESSORIES ...................................................48 - 54
CRIMP CONTACTS
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
CLOSED CRIMP BARREL
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
REELS FOR AUTOMATIC FEED PNEUMATIC CRIMP TOOLS
For SDD crimping information and
crimp tools, see pages 13, 14, and 16.
Contacts may be supplied in plastic carriers, packaged in reels holding 2,000
contacts for use with the automatic feed pneumatic crimp tools, catalog part num-
ber 9550-1. The same type carrier is used for both male and female contacts.
All male and female crimp contacts can be ordered in reels by adding letter “R”
after the contact part number, such as MC8022DR-50 for a male contact and
FC8022DR-50-1202.0 for female contact.
Enlarged section of plastic contact carriers
Material: Leaded nickel copper.
Plating: 0.000050 inch (1.25 µ) gold over copper. Material: Brass.
Plating: 0.000050 inch (1.25 µ) gold over copper.
FEMALE CONTACT (“CLOSED ENTRY”DESIGN) MALE CONTACT
Brass Shroud
0.150
(3.81)
B Ø
C Ø
0.030 Ø
(0.76)
A
0.150
(3.81)
C Ø
B Ø
A
Crimp contacts may be supplied kitted with connector or ordered separately.
PART
NUMBER WIRE SIZE
AWG/(mm2)AB ØC Ø
MC8022D-50 22 / 24 / 26 / 28 / 30
(0.3/0.25/0.12/0.08/0.05) 0.531
(13.49) 0.035
(0.89) 0.047
(1.19)
PART
NUMBER WIRE SIZE
AWG/(mm2)AB ØC Ø
FC8022D-50-1202.0 22 / 24 / 26 / 28 / 30
(0.3/0.25/0.12/0.08/0.05) 0.518
(13.16) 0.035
(0.89) 0.047
(1.19)
Positronic
Industries, Inc. 10
CODE 4, 0.450(11.43) CONTACT EXTENSION
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
STRAIGHT PRINTED BOARD MOUNT CONTACTS
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
0.078(1.98), Typical
0.078(1.98), Typical
Numbering shown is rear view of male
and face view of female.
Push-on Fastener;
Beryllium Copper.
0.020(0.51) Ø0.125(3.18), Nominal
0.082(2.08), Typical
0.082(2.08), Typical
0.082(2.08), Typical
0.082(2.08), Typical
0.082(2.08), Typical
D
0.082(2.08), Typical
0.082(2.08), Typical
D
Fixed
Female
Jackscrews
Swaged spacer with push-
on fastener; phosphor
bronze.
L
Fixed Female
Jackscrews
0.020(0.51) Ø
0.375
(9.53)
0.030 Ø
(0.76) D Ø
D Ø
A
Brass Shroud
A
D
C
A
±0.008
B
90˚ PRINTED BOARD MOUNT CONNECTOR
Contact
Material: Phosphor bronze.
Plating: 0.000050 inch (1.25 µ) gold over copper.
FEMALE CONTACT (“CLOSED ENTRY”DESIGN) MALE CONTACT
Straight printed board mount contacts are supplied in the connector.
For straight printed board
mount contacts, specify
Code Number in Step 4 of
the Ordering Information.
Specify Code 4
in Step 4 of the
Ordering
Information.
CODE
NUMBER LD ØA
30.150
(3.81) 0.020
(0.51) 0.725
(18.42)
32 0.300
(7.62) 0.020
(0.51) 0.865
(21.97)
CODE
NUMBER LD ØA
30.150
(3.81) 0.020
(0.51) 0.737
(18.72)
32 0.300
(7.62) 0.020
(0.51) 0.877
(22.28)
Typical Part Number:
SDD78M4R7NT2G
Typical Part Number:
SDD104M4R7NT2G
Typical Part Number:
SDD62F3S60T2G
Typical Part Number:
SDD44F4R7NT2G
SDD004R7000 0.450(11.43) CONTACT EXTENSION
PART NUMBER A B C D
SDD1504R7000 1.204
(30.58) 0.984
(24.99) 0.528
(13.41) 0.450
(11.43)
SDD2604R7000 1.532
(38.91) 1.312
(33.32) 0.528
(13.41) 0.450
(11.43)
SDD4404R7000 2.072
(52.63) 1.852
(47.04) 0.528
(13.41) 0.450
(11.43)
SDD6204R7000 2.720
(69.09) 2.500
(63.50) 0.528
(13.41) 0.450
(11.43)
SDD7804R7000 2.626
(66.70) 2.406
(61.11) 0.573
(14.55) 0.450
(11.43)
SDD10404R7000 2.720
(69.09) 2.500
(63.50) 0.614
(15.60) 0.450
(11.43)
Positronic
Industries, Inc.
11
90˚ AND STRAIGHT PRINTED BOARD
CONTACT HOLE PATTERN
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
SDD62 MALE
Mount connector with mating face positioned to follow direction of arrows.
Suggest 0.035(0.89) Ø hole for contact termination positions.
Suggest 0.123 ±0.003(3.12) Ø hole for mounting connector with push-on fasteners.
2.500(63.50)
1.250(31.75) 0.973
(24.71)
SDD104 FEMALE
2.500(63.50)
1.250(31.75)
0.082(2.08), Typical 0.095(2.41), Typical
0.967
(24.56)
SDD104 MALE 2.500(63.50)
0.967(24.56)
0.082(2.08), Typical
0.095(2.41), Typical
1.250(31.75)
0.095(2.41), Typical 0.078
(1.98)
0.078
(1.98)
SDD62 FEMALE
2.500(63.50)
1.250(31.75) 0.975
(24.77)
0.095(2.41), Typical 0.078
(1.98)
0.078
(1.98)
SDD78 MALE
2.406(61.11)
1.203(30.56) 0.903
(22.94)
0.095(2.41),
Typical
0.041(1.04)
0.082
(2.08)
0.082
(2.08)
0.082
(2.08)
SDD78 FEMALE
2.406(61.11)
1.203(30.56) 0.903
(22.94)
0.095(2.41), Typical
0.041(1.04)
0.082
(2.08)
0.082
(2.08)
0.082
(2.08)
SDD44 FEMALE 1.852(47.04)
0.926(23.52) 0.655(16.64)
0.090(2.29), Typical 0.078
(1.98)
0.078
(1.98)
SDD44 MALE 1.852(47.04)
0.926(23.52) 0.650(16.51)
0.090(2.29), Typical 0.078
(1.98)
0.078
(1.98)
SDD26 FEMALE 1.312(33.32)
0.656
(16.66) 0.385(9.78)
0.090(2.29), Typical 0.078
(1.98)
0.078
(1.98)
SDD26 MALE 1.312(33.32)
0.656
(16.66) 0.380(9.65)
0.090(2.29),
Typical 0.078
(1.98)
0.078
(1.98)
SDD15 FEMALE 0.984(24.99)
0.492
(12.50) 0.215(5.46)
0.090(2.29), Typical 0.078
(1.98)
0.078
(1.98)
SDD15 MALE 0.984(24.99)
0.492
(12.50)
0.190(4.83)
0.090(2.29), Typical 0.078
(1.98)
0.078
(1.98)
Positronic
Industries, Inc. 12
Positronic
Industries, Inc.
13
USE INDICATED POSITRONIC TOOLS FOR BEST RESULTS
CRIMPING INFORMATION FOR SDD SERIES CRIMP CONTACTS
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
Step 1: Strip wire to indicated length.
Step 2: Crimp wire to contact. For Hand Crimp Tool: - Place contact into crimping tool.
- Insert wire into contact.
- Center contact by slowly closing the
crimping tool until the crimp indenters
make contact with the crimp barrel.
- Complete the cycle of the crimping tool in
one smooth motion.
- Remove the crimped contact.
Take Care Not To: - Damage or remove strands.
- Untwist or overtwist strands.
- Leave insulation particles on strands.
- Damage insulation.
For Automatic Feed Pneumatic Crimp Tool: - Insert the wire into the contact, positioned in the
crimp tool by the plastic carrier.
- Depress the activating device of the crimping
tool to start the crimping cycle.
- Remove the crimped contact.
0.150
(3.81)
Insulation
Stranded Wire
±0.010
Strands damaged
or removed by
stripping tool.
Insulation cut
incorrectly.
Strands overtwisted.
Particles of insula-
tion on the stripped
part of the wire.
Wire insulation
damaged.
Strands untwisted.
Examples of Stripping Faults
Correctly Stripped Wire
CRIMPING INFORMATION FOR SDD SERIES CRIMP CONTACTS
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Conductor tensile strength values
are derived using silver tin-plated
copper wires.
Values may change depending
upon what type of wire is used.
Wire Insulation,
Typical
Crimp to meet recommended
tensile strength.
Stripped wires compressed
for improved conduction. 8 Crimp
Indents
Crimp indents too close
to inspection hole.
Strands not visible
through inspection hole.
Strands visible beyond
insulation support.
Stripped part of
the wire too long. Stripped part of
the wire too short. Crimp indents incorrectly located.
Step 3: Inspect the crimp. For All Tools: - Strands to be visible through the inspection hole.
- Strands not to be visible beyond the insulation support.
- Crimped contact to meet recommended conductor tensile
force shown in chart.
- Check for peeled gold and bent contacts.
Correctly Crimped Contact
Cross Section
of Correctly Crimped Contact
Examples of Crimping Faults
Positronic Recommended
Conductor Tensile Strength
WIRE SIZE
AWG/(mm2)AXIAL LOAD
POUNDS/(N)
24
(0.25) 8
(36)
28
(0.08) 3
(13)
26
(0.12) 5
(22)
30
(0.05) 1.5
(4.4)
22
(0.3) 12
(53)
See page 16 for contact
crimping tool information.
CRIMP TOOLS POSITIONERS FOR
FC8022D-50-1202.2 POSITIONERS FOR
MC8022D-50
9507, HAND CRIMP TOOL 9502-3 9502-4
9550-1, AUTOMATIC FEED,
PNEUMATIC STRIP
AND CRIMP TOOL Supplied in reels. Supplied in reels.
Positronic Recommended Tools
Positronic
Industries, Inc. 14
Positronic
Industries, Inc.
15
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Specify the complete connector by following Steps 1 through 9.
Insert “0” when a step is not used.
ORDERING INFORMATION - CODE NUMBERING SYSTEM
✽NOTE:
For additional information on accessories listed
in Steps 5, 6, and 7, see the Accessory Section,
pages 48-54.
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
For SDD crimping tool information,
see pages 13, 14, and 16.
1 2 3 4 5 6
SDD 62 F 4 R7 NT6
7
G
89
STEP
STEP 1 - Basic Series
SDD Series
STEP 2 - SDD Series Connector Variants
15, 26, 44, 62, 78, 104
STEP 3 - Connector Gender
M -Male
F -Female
STEP 4 - Contact Termination Type
0 - Ordered without contacts.
1 - Crimp, 22 AWG - 30 AWG (0.3 mm2- 0.05 mm2).
3 - Solder, Straight Printed Board Mount with 0.150(3.81) Tail Length.
32 - Solder, Straight Printed Board Mount with 0.300(7.62) Tail Length.
4 - Solder, 90˚ Printed Board Mount with 0.450(11.43) Contact
Extension.
✽ STEP 7 - Locking and Polarizing Systems
0 - None.
T - Fixed Female Jackscrews.
T2 - Fixed Female Jackscrews.
T6 - Fixed Male and Female Polarized Jackscrews.
E - Rotating Male Jackscrews.
E2 - Rotating Male Screw Locks.
E6 - Rotating Male and Female Polarized Jackscrews.
✽ STEP 6 - Hoods and Push-On Fasteners
0 - None.
H - Hood, Top Opening, Brass.
M - Hood, Top Opening, Aluminum, see page 52 for
complete listing of options.
N - Push-on Fastener for 90˚ Mounting Brackets.
STEP 8 - Shell Options
G - Gold over Copper Plate.
D - Gold over Copper Plate and Dimpled.
✽ STEP 5 - Mounting Style
0 - Mounting Hole, 0.120(3.05) Ø.
B3 - Bracket, Mounting, 90˚ Metal with Cross Bar.
F - Float Mounts, Universal.
P - Threaded Post, Brass, 0.375(9.53) Length.
R2 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Thread Fixed Female Jackscrews with Cross Bar.
R6 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 0.120
(3.05) Ø Mounting Hole with Cross Bar.
R7 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Threads with Cross Bar.
R8 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Locknut with Cross Bar.
S - Swaged Spacer, 4-40 Threads, 0.375(9.53) Length.
S2 - Swaged Spacer, 4-40 Threads, 0.125(3.18) Length.
S5 - Swaged Locknut, 4-40 Threads.
S6 - Swaged Spacer with Push-on Fastener, 4-40 Threads, 0.375(9.53)
Length.
STEP 9 - Special Options
Consult Sales Department.
SPACE FLIGHT APPLICATION, HIGH DENSITY
SUBMINIATURE-D CONNECTORS
SDD
SERIES
This fast-cycling automatic feed, strip and crimp tool pro-
duces an 8 indent crimp on wire sizes 22 AWG (0.3 mm2)
through 30 AWG (0.05 mm2). SDD Series contacts must
be ordered on reels.
To order, specify part number 9550-1. Foot control valve
is supplied as a standard accessory.
This miniature step adjustable hand crimping tool pro-
duces an 8 indent crimp configuration and will crimp wire
sizes 22 AWG (0.3 mm2) through 30 AWG (0.05 mm2).
To crimp female contacts, order contact positioner 9502-3.
To crimp male contacts, order contact positioner 9502-4.
Each positioner is equipped with a data plate which gives
the correct crimp-depth setting for each wire size, and
must be used with 9507 tool frame for best results when
crimping SDD Series contacts.
One end of this tool is used to insert contacts into SDD
Series connectors. The other end is used to extract con-
tacts. This is accomplished by sliding the extraction tip
down the wire into the connector until it bottoms against
the contact. A slight rotation while pushing will release the
contacts, which are then extracted by simultaneously
pulling on the wire.
MINIATURE STEP ADJUSTABLE TOOL
(M22520/2-01)
Part No. 9507
INSERTION/REMOVAL TOOL
(M81969/1-04)
AUTOMATIC FEED,
STRIP AND CRIMP TOOL,
PNEUMATICALLY ACTUATED
Part No. 9550-1
Positronic
Industries, Inc. 16
Positronic
Industries, Inc.
17
Space
Combo-D
Series
Size 20 Signal Contacts,
Fixed Solder Cup and
Printed Board Mountable
Size 8 Shielded and Power
Removable, P r i n t e d B o a r d
Mountable
Space Application
Quality Connectors
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
Space Combination Contact Subminiature-D connec-
tors, Series SCBM, are space flight application quality rec-
tangular connectors designed especially to withstand the
rigors of launch and subsequent extended space flight.
The SCBM Series features fixed contacts having solder
cup terminations and printed board mount terminations for
panel mounting and 90˚ and straight printed board appli-
cations.
The materials, dimensions, and performance of the
SCBM Series conform to the requirements of DESC draw-
ing 85039 and GSFC S-311-P-10 where applicable. The
SCBM Series fully complies to the outgassing requirements
of ASTM E-595 and NASA-RP-1124.
The SCBM Series utilizes precision machined contacts
with the female contact featuring a “Closed-Entry” design
having a brass protective shroud.
Twenty standard combination contact variants are avail-
able, utilizing six shell sizes. Each connector variant is
offered with contact terminations for solder cup and 90˚
terminations for printed board mounting.
Nonmagnetic cable supports and jackscrew systems
are available.
Visual and mechanical inspection per MIL-DTL-24308 is
performed, additional testing is available. Contact
Technical Sales.
SCBM SERIES CONTACT VARIANTS
FACE VIEW OF MALE OR REAR VIEW OF FEMALE
5W1
5W5 9W4 13W3 17W2 21W1
21WA4
24W7 36W4
47W1 46W4
43W2
25W3 27W2
8W8 13W6 17W5
3W3 7W2 11W1
SHELL SIZE 2
SHELL SIZE 1
SHELL SIZE 3
SHELL SIZE 4
SHELL SIZE 5
SHELL SIZE 6
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
SCBM SERIES TECHNICAL CHARACTERISTICS
MATERIALS AND FINISHES:
Insulator: Glass-filled polyester per MIL-M-24519, UL
94V-0, ASTM E-595, NASA-RP-1124, blue
color.
Signal Contacts: Male Contacts: Precision machined
brass alloy. Female Contacts: Precision
machined high tensile phosphor bronze
with brass shroud.
Signal Contact Plating: 0.000050 inch (1.25 microns) gold over cop-
per plate.
Power Contacts: Machined of high conductivity copper
alloy for both male and female contacts.
Power Contact Plating: 0.000050 inch (1.25 microns) gold over cop-
per plate.
Shielded Contacts: Male Contacts: Precision machined
brass. Female Contacts: Precision
machined high tensile phosphor bronze.
Shielded Contact Plating: Signal Contacts: 0.000050 inch (1.25
microns) gold over copper plate.
Shells: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
Mounting Spacers
and Brackets: Brass with 0.000050 inch (1.25 microns) gold
over copper plate.
Push-On Fasteners: Phosphor bronze or beryllium copper with
0.000050 inch (1.25 microns) gold over
copper plate.
Jackscrew Systems: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
Hoods: Brass with 0.000050 inch (1.25 microns) gold
over copper plate or aluminum yellow chro-
mate conversion or black anodize.
ELECTRICAL CHARACTERISTICS:
SIGNAL CONTACTS:
Contact Current Rating: 7.5 amps, nominal.
Initial Contact
Resistance: 0.008 ohms, maximum.
Proof Voltage: 1,000 V r.m.s.
POWER CONTACTS:
Contact Current Rating: 10, 15, 20, 30, and 40 amperes, nominal.
Initial Contact
Resistance: 0.005 ohms, maximum.
Proof Voltage: 1,000 V r.m.s.
SHIELDED CONTACTS:
Initial Contact
Resistance: 0.008 ohms, maximum.
Nominal Impedance: 50 ohms.
Insertion Loss: -0.46 dB at 1 GHz
-1.5 dB at 2 GHz
VSWR: 1.15 average at 1 GHz
1.56 average at 2 GHz
Above values measured using frequency domain techniques.
Proof Voltage: 1,000 V r.m.s.
CONNECTOR:
Insulator Resistance: 5 G ohms.
Creepage and
Clearance Distance: 0.039 inch (1.0 mm), minimum.
Working Voltage: 300 V r.m.s.
Residual Magnetism: 20 Gamma, maximum.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55˚C to +125˚C.
Damp Heat, Steady State: 21 days.
MECHANICAL CHARACTERISTICS:
Signal Contacts, Fixed: Size 20 contacts. Male Contact: 0.040
inch (1.02 mm) diameter. Female
Contact: Closed entry design with brass
shroud.
Contact Retention in Insulator: Signal Contacts: 9 lbs. (40N). Power,
and Shielded Contacts: 22 lbs. (98N).
Resistance
to Solder Iron Heat: 500˚F (260˚C) for 10 seconds duration
per IEC 512-6.
Signal Contact Terminations:
Solder Contacts: 0.042 inch (1.06 mm) minimum hole
diameter for 20 AWG (0.5 mm2) wire,
maximum.
Straight Printed
Board Mount: 0.028 inch (0.71 mm) diameter.
90˚ Printed Board Mount: 0.028 inch (0.71 mm) diameter.
Power Contacts,
Removable, Crimp or Size 8 contacts. Male Contact: 0.142
Solder Terminations: inch (3.61 mm) diameter. Female
Contact: Features Large Surface Area
(L.S.A.) Closed entry design utilizing
BeCu mechanical retention member.
Male and female contacts have termina-
tions for wire sizes 8, 12, and 16 AWG.
Power Contacts,
Printed Board Mount: Size 8 contact. Male Contact: 0.142
inch (3.61 mm) diameter. Printed board
terminations with 0.078 inch (1.98 mm)
and 0.125 inch (3.18 mm) diameters.
Shielded Contacts,
Removable: See table of maximum cable sizes for
contact termination dimensions, pages 34
and 35.
Shells: Male shells may be dimpled for EMI/ESD
ground paths.
Polarization: Trapezoidally shaped shells and polar-
ized jackscrews.
Mounting to Angle Brackets: Jackscrews and riveted fasteners with
0.120 inch (3.05 mm) diameter hole, and
threaded riveted fasteners with 4-40
threads and polyester inserts.
Mounting to Printed Board: Rapid installation push-on fasteners and
threaded posts.
Locking Systems: Jackscrews.
Mechanical Operations: 1,000 operations per IEC 512-5.
SCBM5W5F85000G SCBM9W4M65000G
Positronic
Industries, Inc. 18
Positronic
Industries, Inc.
19
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
STANDARD SHELL ASSEMBLY
SCBM3W3M0000G SCBM5W5M0000G
DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE.
SHELL SIZE A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 G
±0.010 H
±0.010 K
±0.005 M
±0.010
SHELL SIZE 1
MALE 1.213
(30.81) 0.666
(16.92) 0.984
(24.99) 0.329
(8.36) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
SHELL SIZE 1
FEMALE 1.213
(30.81) 0.643
(16.33) 0.984
(24.99) 0.311
(7.90) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 2
MALE 1.541
(39.14) 0.994
(25.25) 1.312
(33.32) 0.329
(8.36) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
SHELL SIZE 2
FEMALE 1.541
(39.14) 0.971
(24.66) 1.312
(33.32) 0.311
(7.90) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 3
MALE 2.088
(53.04) 1.534
(38.96) 1.852
(47.04) 0.329
(8.36) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 3
FEMALE 2.088
(53.04) 1.511
(38.38) 1.852
(47.04) 0.311
(7.90) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 4
MALE 2.729
(69.32) 2.182
(55.42) 2.500
(63.50) 0.329
(8.36) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 4
FEMALE 2.729
(69.32) 2.159
(54.84) 2.500
(63.50) 0.311
(7.90) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 5
MALE 2.635
(66.93) 2.079
(52.81) 2.406
(61.11) 0.441
(11.20) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 5
FEMALE 2.635
(66.93) 2.064
(52.43) 2.406
(61.11) 0.423
(10.74) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 6
MALE 2.729
(69.32) 2.212
(56.18) 2.500
(63.50) 0.503
(12.78) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 6
FEMALE 2.729
(69.32) 2.189
(55.60) 2.500
(63.50) 0.485
(12.32) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.243
(6.17) 0.429
(10.90)
OPTIONAL SHELL ASSEMBLY WITH UNIVERSAL FLOAT MOUNTS
OPTIONAL SHELL ASSEMBLY
0.120 (3.05)±0.005 Ø Mounting Hole, two places
0.154 (3.91) Ø Mounting Hole available 0.086 (2.18)+0.005 -0.000 Ø
Mounting Hole, two places
0.120(3.05) ±0.010
0.032(0.81)
Total diametral float
G
H
0.050(1.27)±0.010
0.036(0.91)±0.008
K
M
0.220(5.59), Max.
10˚ Typical
B
E
CA
B1
D1 D
0.120 (3.05) ±0.005 Ø
Mounting Hole, two places
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
SOLDER CONNECTOR
Typical Part Number: SCBM7W2F200T6G
SCBM21WA4M2000G WITH MS4820M SCBM21WA4F65S00G
Typical Part Number: SCBM7W2M200T2G
Typical Part Number: SCBM17W2F35S60T2G
Fixed male and female polarized jackscrews available.
Specify Code T6 in Step 7 of the Ordering Information.
For solder contacts, specify Code 2 in
Step 4 of the Ordering Information.
For straight printed board
mount contacts, specify
Code Number in Step 4 of
the Ordering Information.
Fixed Female
Jackscrew
Fixed Female
Jackscrews
20 A WG, max.
(0.5 mm2)
0.125
(3.18) 0.345
(8.76)
Fixed Male
Jackscrew
STRAIGHT PRINTED BOARD MOUNT CONNECTOR
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Swaged spacer with
push-on fastener,
phosphor bronze.
0.010 Min.
(0.25)
0.028 Ø
(0.71)
Fixed Female Jackscrews
0.250
(6.35)
0.170
(4.32)
WITH SIZE 8 CONTACTS
CODE
NUMBER D Ø
3---------
35 0.078
(1.98)
37 0.125
(3.18) D Ø
Positronic
Industries, Inc. 20
Positronic
Industries, Inc.
21
SCBM
SERIES
SPACE FLIGHT APPLICATION
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
PRINTED BOARD MOUNTED POWER CONTACTS
STRAIGHT PRINTED BOARD MOUNT POWER CONTACTS
Straight printed board mount power contacts are mounted in connector when ordered.
0.170
(4.32) 0.626
(15.90)
0.142
(3.61)
0.634
(16.10)
✽FEMALE CLOSED ENTRY, L.S.A. MALE
Ø
PART
NUMBER AØCURRENT
RATING
FDS4314M 0.078
(1.98) 15 Amps.
FDS4310M 0.125
(3.18) 30 Amps.
PART
NUMBER AØCURRENT
RATING
MDS4314M 0.078
(1.98) 15 Amps.
MDS4310M 0.125
(3.18) 30 Amps.
Material - High conductivity copper alloy.
Plating - 0.000050 inch (1.25µ) gold over copper.
Material - High conductivity copper alloy.
Plating - 0.000050 inch (1.25µ) gold over copper. ✽Note: Female power contacts feature Large Surface Area
(L.S.A.) closed entry contact design which provides
maximum mating surfaces between male and
female contacts and reduced contact resistance
during operation.
RIGHT ANGLE PRINTED BOARD MOUNT POWER CONTACTS
Right angle printed board mount power contacts are mounted in connector when ordered.
✽FEMALE
CLOSED ENTRY, L.S.A.
0.142
(3.61) Ø
BEND
CODE
55
55
75
75
✽
PART
NUMBER CURRENT A REF. B ØCSHELL
SIZE
MRT4314M 15 Amps 0.580
(14.73) 0.078
(1.98) 0.339
(8.61) 1, 2, 3 & 4
MRT4414M 15 Amps 0.692
(17.58) 0.078
(1.98) 0.451
(11.46) 5
MRT4714M 15 Amps 0.661
(16.79) 0.078
(1.98) 0.420
(10.67) 1, 2, 3 & 4
MRT4814M 15 Amps 0.773
(19.63) 0.078
(1.98) 0.520
(13.21) 5
MRT4310M 30 Amps 1.036
(26.31) 0.125
(3.18) 0.810
(20.57) 1, 2, 3 & 4
✽
MRT4410M 30 Amps 1.036
(26.31) 0.125
(3.18) 0.810
(20.57) 5
BEND
CODE
55
55
75
75
✽
PART
NUMBER CURRENT A REF. B ØCSHELL
SIZE
FRT4314M 15 Amps 0.580
(14.73) 0.078
(1.98) 0.339
(8.61) 1, 2, 3 & 4
FRT4414M 15 Amps 0.692
(17.58) 0.078
(1.98) 0.451
(11.46) 5
FRT4714M 15 Amps 0.661
(16.79) 0.078
(1.98) 0.420
(10.67) 1, 2, 3 & 4
FRT4814M 15 Amps 0.773
(19.63) 0.078
(1.98) 0.520
(13.21) 5
FRT4310M 30 Amps 1.036
(26.31) 0.125
(3.18) 0.810
(20.57) 1, 2, 3 & 4
✽
FRT4410M 30 Amps 1.036
(26.31) 0.125
(3.18) 0.810
(20.57) 5
DIMENSIONS ARE IN INCHES (MILLIMETERS)
ALL DIMENSIONS SUBJECT TO CHANGE
(15 AMPS NOMINAL)
RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR
WITH 0.078(1.98) Ø POWER CONTACTS
CODE 5 AND 55, 0.283(7.19) CONTACT EXTENSION
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR
WITH 0.125(3.18) Ø POWER CONTACTS
DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE.
(30 AMPS NOMINAL)
CODE 5 AND 57, 0.283(7.19) CONTACT EXTENSION
Push-on Fastener,
Beryllium Copper.
0.170(4.32), Nominal
Fixed Female
Jackscrews
Specify Code 5 or 57
in Step 4 of the
Ordering Information.
0.810
(20.57)
0.112(2.84),
Typical
D
0.220(5.59), Maximum C
±0.008
B
A
0.028(0.71) Ø
0.125(3.18) Ø
Numbering shown is rear view
of male and face view of female.
0.112(2.84), Typical
0.112(2.84), Typical
0.810
(20.57)
D
Typical Part Number:
SCBM17W2M57R7NT2G Typical Part Number:
SCBM36W4F57R7NT2G
Push-on Fastener,
Beryllium Copper.
0.170(4.32), Nominal
Fixed Female
Jackscrews
Specify Code 5 or 55
in Step 4 of the
Ordering Information.
0.339
(8.61)
0.112(2.84),
Typical
D
0.220(5.59), Maximum C
±0.008
B
A
0.028(0.71) Ø
0.078(1.98) Ø
Numbering shown is rear view
of male and face view of female. 0.112(2.84), Typical
0.112(2.84), Typical
0.451
(11.56)
D
Typical Part Number:
SCBM17W2M55R7NT2G Typical Part Number:
SCBM36W4F55R7NT2G
SCBM00✽R7000 0.283(7.19) CONTACT EXTENSION
SHELL SIZE A B C D
SHELL SIZE 1 1.204
(30.58) 0.984
(24.99) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 2 1.532
(38.91) 1.312
(33.32) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 3 2.072
(52.63) 1.852
(47.04) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 4 2.720
(69.09) 2.500
(63.50) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 5 2.626
(66.70) 2.406
(61.11) 0.395
(10.03) 0.283
(7.19)
SCBM00✽R7000 0.283(7.19) CONTACT EXTENSION
SHELL SIZE A B C D
SHELL SIZE 1 1.204
(30.58) 0.984
(24.99) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 2 1.532
(38.91) 1.312
(33.32) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 3 2.072
(52.63) 1.852
(47.04) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 4 2.720
(69.09) 2.500
(63.50) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 5 2.626
(66.70) 2.406
(61.11) 0.395
(10.03) 0.283
(7.19)
Positronic
Industries, Inc. 22
Positronic
Industries, Inc.
23
(30 AMPS NOMINAL)
METRIC SYSTEM 90˚ PRINTED BOARD MOUNT CONNECTOR
WITH 0.125(3.18) Ø POWER CONTACTS
CODE 7 AND 77, 0.370(9.40) CONTACT EXTENSION
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
METRIC SYSTEM 90˚ PRINTED BOARD MOUNT CONNECTOR
WITH 0.078(1.98) Ø POWER CONTACTS
(15 AMPS NOMINAL)
CODE 7 AND 75, 0.370(9.40) CONTACT EXTENSION
DIMENSIONS ARE IN
INCHES (MILLIMETERS).
ALL DIMENSIONS ARE
SUBJECT TO CHANGE.
0.170(4.32), Nominal
Fixed Female
Jackscrews
Specify Code 7 or 75
in Step 4 of the
Ordering Information. 0.420
(10.67) 0.100(2.54),
Typical
D
C
0.125(3.18) Ø, Typical
0.220(5.59), Maximum
±0.008
B
A
0.024(0.61) Ø0.078(1.98) Ø
Numbering shown is rear view
of male and face view of female.
0.100(2.54), Typical
0.100(2.54), Typical
0.520
(13.21)
D
Typical Part Number:
SCBM17W2M75R70T2G Typical Part Number:
SCBM36W4M75R70T2G
0.170(4.32),
Nominal
Fixed Female
Jackscrews
Specify Code 7 or 77
in Step 4 of the
Ordering Information.
0.810(20.57) 0.100(2.54),
Typical
D
C
0.125(3.18) Ø, Typical
0.220(5.59), Maximum
±0.008
BA
0.024(0.61) Ø0.125(3.18) Ø
Numbering shown is rear view
of male and face view of female.
0.100(2.54), Typical
0.100(2.54), Typical
0.810
(20.57)
D
Typical Part Number:
SCBM17W2M77R70T2G
SCBM00✽R7000 0.370(9.40) CONTACT EXTENSION
SHELL SIZE A B C D
SHELL SIZE 1 1.204
(30.58) 0.984
(24.99) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 2 1.532
(38.91) 1.312
(33.32) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 3 2.072
(52.63) 1.852
(47.04) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 4 2.720
(69.09) 2.500
(63.50) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 5 2.626
(66.70) 2.406
(61.11) 0.470
(11.94) 0.370
(9.40)
SCBM00✽R7000 0.370(9.40) CONTACT EXTENSION
SHELL SIZE A B C D
SHELL SIZE 1 1.204
(30.58) 0.984
(24.99) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 2 1.532
(38.91) 1.312
(33.32) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 3 2.072
(52.63) 1.852
(47.04) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 4 2.720
(69.09) 2.500
(63.50) 0.420
(10.67) 0.370
(9.40)
SHELL SIZE 5 2.626
(66.70) 2.406
(61.11) 0.470
(11.94) 0.370
(9.40)
Typical Part Number:
SCBM36W4M77R70T2G
CONNECTOR VARIANT 46W4
(30 AMPS NOMINAL)
SHELL SIZE 6
90˚ PRINTED BOARD MOUNT CONNECTOR
WITH 0.125(3.18) Ø POWER CONTACTS
CODE 5 AND 57, 0.283(7.19) CONTACT EXTENSION
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Push-on Fastener,
Beryllium Copper.
0.170(4.32),
Nominal
Fixed Female Jackscrews
0.283(7.19) - Specify
Code 5 or 55 in Step
4 of the Ordering
Information. 0.112(2.84), Typical
0.451(11.46)
0.028(0.71) Ø
0.078(1.98) Ø
Numbering shown is rear view
of male and face view of female.
0.507(12.88)
±0.008
2.500(63.50)
2.720(69.09)
Typical Part Number:
SCBM46W4M55R7NT2G
SHELL SIZE 6
90˚ PRINTED BOARD MOUNT CONNECTOR
WITH 0.078(1.98) Ø POWER CONTACTS
CONNECTOR VARIANT 46W4
(15 AMPS NOMINAL)
CODE 5 AND 55, 0.283(7.19) CONTACT EXTENSION
SHELL SIZE 6 CONNECTOR
Push-on Fastener,
Beryllium Copper.
0.170(4.32),
Nominal
Fixed Female Jackscrews
0.283(7.19) - Specify
Code 5 or 57 in Step
4 of the Ordering
Information.
0.112(2.84), Typical
0.451(11.46)
0.028(0.71) Ø
0.125(3.18) Ø
Numbering shown is rear view
of male and face view of female.
0.810
(20.57)
±0.008
2.500(63.50)
2.720(69.09)
Typical Part Number:
SCBM46W4M57R7NT2G
SHELL SIZE 6 CONNECTOR
24
Positronic
Industries, Inc.
Positronic
Industries, Inc.
25
DIMENSIONS ARE IN
INCHES (MILLIMETERS).
ALL DIMENSIONS ARE
SUBJECT TO CHANGE.
Hole identification shown for male connector; use mirror image for female connector.
Mount connector with mating face positioned to follow direction of arrows.
Suggest 0.045(1.14) Ø hole for signal contact termination positions.
Suggest 0.098(2.49) Ø hole for 0.078(1.98) Ø power contact terminations.
Suggest 0.145(3.68) Ø hole for 0.125(3.18) Ø power contact termination positions.
Suggest 0.123 ±0.003 (3.12) Ø hole for mounting connector with push-on fasteners.
5W1 3W3
7W2 11W1
13W3
9W4
5W5
17W2 21W1
8W8
21WA4
17W5
13W6
25W3 27W2
24W7 43W2
47W1
46W4
36W4
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
CODE
NUMBER 3, 35,
& 37 5 & 55 7 & 75
X0.112
(2.84) 0.112
(2.84) 0.100
(2.54)
Y0.056
(1.42) 0.056
(1.42) 0.050
(1.27)
A0.100
(2.54) 0.112
(2.84) 0.100
(2.54)
B0.050
(1.27) 0.056
(1.42) 0.050
(1.27)
RIGHT ANGLE AND STRAIGHT PRINTED BOARD CONTACT HOLE
PATTERN WITH 0.078(1.98) Ø AND STRAIGHT PRINTED BOARD
MOUNT 0.125(3.18) Ø POWER CONTACTS
Hole identification shown for male connector; use mirror image for female connector.
Mount connector with mating face positioned to follow direction of arrows.
Suggest 0.045(1.14) Ø hole for signal contact termination positions.
Suggest 0.145(3.68) Ø hole for 0.125(3.18) Ø power contact termination positions.
Suggest 0.123 ±0.003 (3.12) Ø hole for mounting connector with push-on fasteners.
5W1 3W3 7W2 11W1
13W3
9W4
5W5
17W2 21W1
8W8
21WA4
17W5
13W6
25W3 27W2
24W7 43W2
47W1
46W4
36W4
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CODE
NUMBER A B C X Y
5 & 57 0.471
(11.96) 0.415
(10.54) 0.359
(9.12) 0.112
(2.84) 0.056
(1.42)
7 & 77 0.390
(9.91) 0.340
(8.64) 0.290
(7.37) 0.100
(2.54) 0.050
(1.27)
RIGHT ANGLE PRINTED BOARD CONTACT HOLE PATTERN
WITH 0.125(3.18) Ø POWER CONTACTS
26
Positronic
Industries, Inc.
Positronic
Industries, Inc.
27
✽Technical characteristics are listed on page 33.
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
STRAIGHT PRINTED BOARD MOUNT SHIELDED CONTACTS ARE MOUNTED IN CONNECTOR WHEN ORDERED.
90˚ PRINTED BOARD MOUNT SHIELDED CONTACTS ARE MOUNTED IN CONNECTOR WHEN ORDERED.
STRAIGHT PRINTED BOARD MOUNT SHIELDED CONTACTS
RIGHT ANGLE PRINTED BOARD MOUNT SHIELDED CONTACTS
PRINTED BOARD MOUNT SHIELDED CONTACTS
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
Material: Copper alloy with PTFE teflon insulator.
Signal Contact Plating: 0.000050 inch (1.25 µ) gold over copper.
Contact Body Plating: 0.000050 inch (1.25 µ) gold over copper.
PART
NUMBER A B C
FDS4201M 0.481
(12.22) 0.025
(0.64) 0.181
(4.60)
PART
NUMBER A B C
MDS4201M 0.489
(12.42) 0.025
(0.64) 0.181
(4.60)
C
Suggest 0.045(1.14) Ø Hole
0.200
(5.08)
0.200
(5.08)
0.156
(3.96)
0.200
(5.08)
0.156
(3.96)
A
B
A
B
0.040
(1.02)Ø
0.037(0.94)
across points
0.152
(3.86) Ø
0.100(2.54)
Suggest 0.045(1.14) Ø
Hole
D
B
C
A
0.100
(2.54)
0.037(0.94)
across points
0.200
(5.08)
0.040
(1.02)Ø0.152
(3.86)Ø
C
A
B
0.162
(4.11)
0.162
(4.11)
FDS4201M and MDS4201M
Contact Hole Pattern
✽Technical characteristics are listed on page 33.
Material: Copper alloy with PTFE teflon insulator.
Signal Contact Plating: 0.000050 inch (1.25 µ) gold over copper.
Contact Body Plating: 0.000050 inch (1.25 µ) gold over copper.
FRT4201M and MRT4201M
Contact Hole Pattern
FEMALE MALE
FEMALE MALE
PART
NUMBER A B D
MRT4201M 0.829
(21.06) 0.240
(6.10) 0.470
(11.94)
C
0.253
(6.43)
PART
NUMBER A B D
FRT4201M 0.827
(21.01) 0.240
(6.10) 0.470
(11.94)
C
0.259
(6.58)
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
D - Specify Code
85 in Step 4 of the
Ordering Information.
RIGHT ANGLE PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED
CONTACTS
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CODE 85, CONNECTOR WITH FRT4201M OR MRT4201M CONTACTS
SCBM00850000 0.283(7.19) CONTACT EXTENSION
SHELL SIZE A B C D
SHELL SIZE 1 1.204
(30.58) 0.984
(24.99) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 2 1.532
(38.91) 1.312
(33.32) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 3 2.072
(52.63) 1.852
(47.04) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 4 2.720
(69.09) 2.500
(63.50) 0.339
(8.61) 0.283
(7.19)
SHELL SIZE 5 2.620
(66.70) 2.406
(61.11) 0.395
(10.03) 0.545
(13.84)
Fixed Female
Jackscrews
0.250(6.35)
0.028
(0.71) Ø
Push-on Fastener, Phosphor Bronze
Numbering shown is rear view of
male and face view of female.
Numbering shown is
rear view of male and
face view of female.
0.156(3.96)
0.025(0.64) 0.028(0.71) Ø
0.037(0.94)
across points
Fixed Female
Jackscrews
C
0.112(2.84), Typical
0.470(11.94)
0.170(4.32),
Nominal
0.156(3.96)
Push-on Fastener,
Beryllium Copper
0.028
(0.71) Ø
0.028(0.71) Ø
1 place.
0.037(0.94)
across points,
2 places.
A
±0.008
B
0.170(4.32)
Typical Part Number:
SCBM17W2M65S60T2G
Typical Part Number:
SCBM36W4M85R7NT2G
Typical Part Number:
SCBM17W2M85R7NT2G
D - Specify Code
85 in Step 4 of the
Ordering Information.
0.470(11.94)
0.112(2.84),
Typical
NOTE: Shell size 5 connectors are supplied
inverted when ordered with 90°print-
ed board mount shielded contact.
28
Positronic
Industries, Inc.
STRAIGHT PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED
CONTACTS
CODE 65, CONNECTOR WITH FDS4201M OR MDS4201M CONTACTS
Positronic
Industries, Inc.
29
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Hole identification shown is for male connector; use mirror image for female connector.
STRAIGHT PRINTED BOARD MOUNT CONTACT HOLE PATTERN
WITH FDS4201M AND MDS4201M SHIELDED CONTACTS
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
Suggest 0.045(1.14) Ø hole for signal contact termination position.
Suggest 0.123 ±0.003 (3.12) Ø hole for mounting connector with push-on fastener.
5W1
5W5
21W1
17W5
27W2
43W2
9W4
8W8
21WA4
24W7
47W1
25W3
36W4
46W4
13W3 17W2
13W6
3W3 7W2 11W1
Hole identification shown is for male connector; use mirror image for female connector.
Mount connector with mating face positioned to follow direction of arrow.
90˚ PRINTED BOARD MOUNT CONTACT HOLE PATTERN
WITH FRT4201M AND MRT4201M SHIELDED CONTACTS
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
Suggest 0.045(1.14) Ø hole for signal contact termination position.
Suggest 0.123 ±0.003 (3.12) Ø hole for mounting connector with push-on fastener.
5W1
5W5
21W1
17W5
27W2
9W4
8W8
13W3 17W2
13W6
3W3 7W2 11W1
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
21WA4
24W7
25W3
43W2 47W1
0.109 (2,77) Typ.
0.109 (2,77) Typ. 0.109 (2,77) Typ.
0.112 (2,84) 0.112 (2,84)
0.112 (2,84)0.112 (2,84)
0.109 (2,77) Typ.
0.055 (1,40) Typ.
0.055 (1,40) Typ. 0.055 (1,40) Typ.
0.270 (6,86) Typ. 0.270 (6,86)
0.540 (13,72)
0.540 (13,72)
0.150 (3,81) 0.150 (3,81)
0.810 (20,57)
0.810 (20,57)
0.810 (20,57)
0.200 (5,08) 0.200 (5,08)
0.075 (1,91) 0.075 (1,91)
1.203 (30,56) Typ. 1.203 (30,56) Typ.
1.203 (30,56) Typ.
1.203 (30,56) Typ.
0.374
(9,50)
0.200 (5,08)
0.374 (9,50)
0.100 (2,54)
0.100
(2,54) 0.100
(2,54)
0.075 (1,91)
36W4
30
Positronic
Industries, Inc.
Positronic
Industries, Inc.
31
Shell Size 1
5W1
Shell Size 2
3W3, 7W2, 11W1
Shell Size 3
5W5, 9W4, 13W3, 17W2, 21W1
Shell Size 4
8W8, 13W6, 17W5, 21WA4, 25W3, 27W2
Shell Size 5
24W7, 36W4, 43W2, 47W1
Shell Size 6
46W4
✽NOTE:
For additional information on accessories listed
in Steps 5, 6, and 7, see the Accessory Section,
pages 48-54.
✽✽ NOTE:
Not available on Shell Size 6, CBD 46W4.
STEP
STEP 1 - Basic Series
SCBM Series - Space Conformance with
“Closed Entry” Signal Contacts
STEP 2 - Space Combo-D Series
Connector Variants
STEP 3 - Connector Gender
M -Male
F -Female
STEP 4 - Contact Termination Type
2 - Solder, Signal Contacts only.
3 - Solder, Straight Printed Board Mount with Signal Contacts,
0.170(4.32) Tail Length.
35 - Solder, Straight Printed Board Mount with Signal and
0.078(1.98) Ø Power Contacts, 0.170(4.32) Tail Length.
37 - Solder, Straight Printed Board Mount with Signal and
0.125(3.18) Ø Power Contacts, 0.170(4.32) Tail Length.
5 - Solder, 90˚ Printed Board Mount with Signal Contacts only,
0.283(7.19) Signal Contact Extension.
55 - Solder, 90˚ Printed Board Mount with Signal and 0.078(1.98)
Ø Power Contacts, 0.283(7.19) Signal Contact Extension.
57 - Solder, 90˚ Printed Board Mount with Signal and 0.125(3.18)
Ø Power Contacts, 0.283(7.19) Signal Contact Extension.
65 - Solder, Straight Printed Board Mount with Signal and Shielded
Contacts, MDS/FDS 4201M footprint, 0.170(4.32) Signal
Contact Tail Length.
7 - Solder, Metric System 90˚ Printed Board Mount with Signal
Contacts only, 0.370(9.40) Signal Contact Extension.
75 - Solder, Metric System 90˚ Printed Board Mount with Signal
and 0.078(1.98) Ø Power Contacts, 0.370(9.40) Signal
Contact Extension.
77 - Solder, Metric System 90˚ Printed Board Mount with Signal
and 0.125(3.18) Ø Power Contacts, 0.370(9.40) Signal
Contact Extension.
✽✽85 - Solder, 90˚ Printed Board Mount with Signal and Shielded
Contacts, MRT/FRT 4201M Footprint, 0.283(7.19) Signal
Contact Extension.
✽ STEP 7 - Locking and Polarizing Systems
0 - None.
T - Fixed Female Jackscrews.
T2 - Fixed Female Jackscrews.
T6 - Fixed Male and Female Polarized Jackscrews.
E - Rotating Male Jackscrews.
E6 - Rotating Male and Female Polarized Jackscrews.
✽ STEP 6 - Hoods and Push-On Fasteners
0 - None.
H - Hood, Top Opening, Brass.
M - Hood, Top Opening, Aluminum, see page 52 for
complete listing of options.
N - Push-on Fastener for 90˚ Mounting Brackets.
STEP 8 - Shell Options
G - Gold over Copper Plate.
D - Gold over Copper Plate and Dimpled.
✽ STEP 5 - Mounting Style
0 - Mounting Hole, 0.120(3.05) Ø.
B3 - Bracket, Mounting, 90˚ Metal with Cross Bar.
F - Float Mounts, Universal.
P - Threaded Post, Brass, 0.250(6.35) Length.
R2 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Thread Fixed Female Jackscrews with Cross Bar.
R6 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 0.120
(3.05) Ø Mounting Hole with Cross Bar.
R7 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Threads with Cross Bar.
R8 - Bracket, Mounting, 90˚ Metal, Swaged to Connector with 4-40
Locknut with Cross Bar.
S - Swaged Spacer, 4-40 Threads, 0.250(6.35) Length.
S2 - Swaged Spacer, 4-40 Threads, 0.125(3.18) Length.
S5 - Swaged Locknut, 4-40 Threads.
S6 - Swaged Spacer with Push-on Fastener, 4-40 Threads,
0.250(6.35) Length.
STEP 9 - Special Options
Consult Sales Department.
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
SCBM
SERIES
Specify the complete connector by following Steps 1 through 9.
Insert “0” when a step is not used.
ORDERING INFORMATION - CODE NUMBERING SYSTEM
1 2 3 4 5 6
SCBM 17W2 F55 R7 NT2
7
G
89
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
REMOVABLE CRIMP CONTACTS
SOLDER POWER CONTACTS
POWER CONTACTS
REMOVABLE POWER CONTACTS
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SCBM
SERIES
0.402
(10.21)
0.142
(3.61) Ø
Solder contacts may be supplied kitted with connector or ordered separately.
Material: High conductivity copper alloy.
Plating: 0.000050 inch (1.25 µ) gold over copper.
Material: High conductivity copper alloy.
Plating: 0.000050 inch (1.25 µ) gold over copper.
✽FEMALE - CLOSED ENTRY L.S.A.
A
BC
MALE
A
B
C
C
0.142
(3.61) Ø
✽FEMALE - CLOSED ENTRY L.S.A.
0.354
(8.99)
MALE
A
B Ø
0.354
(8.99)
A
B Ø
PART
NUMBER CURRENT
RATING WIRE
SIZE A REF. B ØC Ø
FS4008M 40 AMPS 80.858
(21.79) 0.219
(5.56) 0.188
(4.78)
FS4012M 20 AMPS 12 0.858
(21.79) 0.143
(3.63) 0.112
(2.84)
FS4016M 10 AMPS 16 0.858
(21.79) 0.100
(2.54) 0.069
(1.75)
PART
NUMBER CURRENT
RATING WIRE
SIZE A REF. B ØC Ø
MS4008M 40 AMPS 80.868
(22.05) 0.219
(5.56) 0.188
(4.78)
MS4012M 20 AMPS 12 0.868
(22.05) 0.143
(3.63) 0.112
(2.84)
MS4016M 10 AMPS 16 0.868
(22.05) 0.100
(2.54) 0.069
(1.75)
Crimp power contacts may be supplied with connector or ordered separately.
PART
NUMBER CURRENT
RATING WIRE
SIZE A REF. B ØC MAX.
FC4008M 40 AMPS 80.858
(21.79) 0.181
(4.60) 0.640
(16.26)
FC4012M 20 AMPS 12 0.858
(21.79) 0.101
(2.57) 0.640
(16.26)
FC4016M 10 AMPS 16 0.858
(21.79) 0.067
(1.70) 0.640
(16.26)
PART
NUMBER CURRENT
RATING WIRE
SIZE A REF. B ØC MAX.
MC4008M 40 AMPS 80.882
(22.40) 0.181
(4.60) 0.640
(16.26)
MC4012M 20 AMPS 12 0.882
(22.40) 0.101
(2.57) 0.640
(16.26)
MC4016M 10 AMPS 16 0.882
(22.40) 0.067
(1.70) 0.640
(16.26)
✽NOTE: Female contacts feature Large Surface Area (L.S.A.) “Closed Entry” contact
design which provides maximum mating surfaces between male and female
contact and reduced contact resistance during operation.
9509-0-0 Power Contact Hand Crimp Tool
For use with *C4012M and *C4016M Contacts 9504-17 Power Contact Hand Crimp Tool
For use with *C4008M Contacts 4311-0-0 Power Contact Removal Tool
32
Positronic
Industries, Inc.
Positronic
Industries, Inc.
33
SHIELDED CONTACTS
TECHNICAL CHARACTERISTICS
SPACE FLIGHT APPLICATION
SIZE 8 REMOVABLE HIGH VOLTAGE AND SHIELDED CONTACTS
SCBC
SCBM
SERIES
MATERIALS AND FINISHES:
Insulating Material: (Dielectric) Teflon, PTFE.
Inner Contacts: Brass and Phosphor Bronze, 0.000050
inch (1.25 microns) gold over copper.
Outer Contacts: Brass and Phosphor Bronze, 0.000050 inch
(1.25 microns) gold over copper.
ELECTRICAL CHARACTERISTICS:
Initial Contact Resistance: 0.008 ohms, maximum.
✽ Nominal Impedance: 50 ohms.
✽ Insertion Loss: -0.46 dB at 1 GHz
-1.5 dB at 2 GHz
✽ VSWR: 1.15 average at 1 GHz
1.56 average at 2 GHz
Proof Voltage: 1,000 V r.m.s.
✽Above values measured using frequency domain techniques.
MECHANICAL CHARACTERISTICS:
Removable Contacts: Rear Insertion, front release.
Durability: 500 cycles, minimum.
Vibration: 20g from 10 HZ to 500 HZ.
Shock: 30g - 11 ms.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55˚C to +125˚C.
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT T O CHANGE.
REMOVABLE HIGH VOLTAGE CONTACTS
High voltage contacts are not supplied with connectors and must be ordered separately.
STRAIGHT SOLDER WIRE TERMINATION
90°SOLDER WIRE TERMINATION
20 A WG Max.
20 A WG Max.
20 A WG Max.
20 A WG Max.
0.734
(18.64)
Ref.
0.697
(17.70)
Ref.
0.697
(17.70)
Ref.
0.142
(3.61)
0.142
(3.61)
0.485
(12.32)
0.448
(11.38)
0.040
(1.02)
Ø
Ø
Ø
0.040
(1.02) Ø
0.734
(18.64)
Ref.
MS4820D
MS4920D
FS4820D
FS4920D
MATERIALS AND FINISHES:
Insulators: Teflon, PTFE.
Contacts: Male contacts, brass. Female contacts,
phosphor bronze.
Plating: 0.000050 inch (1.25 microns) gold over
copper.
ELECTRICAL CHARACTERISTICS:
HIGH VOLTAGE CONTACTS
Flash Over Voltage: 3600 V r.m.s.
Proof Voltage: 2700 V r.m.s.
Initial Contact Resistance: 0.008 ohms maximum.
MECHANICAL CHARACTERISTICS:
Size 8 Removable
Contacts: Rear insertion, front release.
Durability: 500 cycles minimum.
Vibration: 20g from 10 Hz to 500 Hz.
Shock: 30g-11ms.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55˚C to +125˚C.
TECHNICAL CHARACTERISTICS
REMOVABLE SHIELDED CONTACTS
SPACE FLIGHT APPLICATION
SIZE 8 REMOVABLE SHIELDED CONTACTS
SCBC
SCBM
SERIES
DIMENSIONS ARE IN
INCHES (MILLIMETERS).
ALL DIMENSIONS ARE
SUBJECT TO CHANGE.
Shielded contacts may be supplied kitted with connector or ordered separately.
TYPE
OF CONTACT PART NUMBER AB ØC MAX. RG CABLE
NUMBER
SOLDER/CRIMP MC4101M FC4101M 0.929
(23.60) 0.040
(1.02) 0.739
(18.77) 178 B/U
196 B/U
SOLDER/CRIMP MC4102M FC4102M 0.929
(23.60) 0.067
(1.70) 0.739
(18.77) 179 B/U
316 /U
SOLDER/CRIMP MC4103M FC4103M 1.037
(26.34) 0.108
(2.74) 0.847
(21.51) 180 B/U
SOLDER/CRIMP MC4104M FC4104M 1.037
(26.34) 0.120
(3.05) 0.847
(21.51) 58 B/U
SOLDER/SOLDER MS4101M FS4101M 0.929
(23.60) 0.040
(1.02) 0.739
(18.77) 178 B/U
196 B/U
SOLDER/SOLDER MS4102M FS4102M 0.929
(23.60) 0.067
(1.70) 0.739
(18.77) 179 B/U
316 /U
SOLDER/SOLDER MS4103M FS4103M 1.037
(26.34) 0.108
(2.74) 0.847
(21.51) 180 B/U
SOLDER/SOLDER MS4104M FS4104M 1.037
(26.34) 0.120
(3.05) 0.847
(21.51) 58 B/U
CRIMP/CRIMP MCC4101M FCC4101M 0.929
(23.60) 0.040
(1.02) 0.739
(18.77) 178 B/U
196 B/U
CRIMP/CRIMP MCC4102M FCC4102M 0.929
(23.60) 0.067
(1.70) 0.739
(18.77) 179 B/U
316 /U
CRIMP/CRIMP MCC4103M FCC4103M 1.037
(26.34) 0.108
(2.74) 0.847
(21.51) 180 B/U
CRIMP/CRIMP MCC4104M FCC4104M 1.037
(26.34) 0.120
(3.05) 0.847
(21.51) 58 B/U
MALE FEMALE
AC
A
B Ø
B Ø
0.152
(3.86) Ø
0.040
(1.02) Ø
Two-step crimping action
for signal and shielding
conductors.
See page 35 for crimp tool
and crimping information.
Signal Contact Plating: 0.000050 inch (1.25 µ) gold over copper .
Contact Body Plating: 0.000050 inch (1.25 µ) gold over copper.
Material: Copper alloy with PTFE teflon insulator.
FEMALE CONTACT MALE CONTACT
STRAIGHT SOLDER/CRIMP CONTACTS
AC
A
B Ø
B Ø
0.152
(3.86) Ø
0.040
(1.02) Ø
FEMALE CONTACT MALE CONTACT
STRAIGHT SOLDER/SOLDER CONTACTS
AC
A
B Ø
B Ø
0.152
(3.86) Ø
0.040
(1.02) Ø
FEMALE CONTACT MALE CONTACT
STRAIGHT CRIMP/CRIMP CONTACTS
34
Positronic
Industries, Inc.
Positronic
Industries, Inc.
35
SOLDERING AND CRIMPING INFORMATION
FOR SCBC AND SCBM SERIES SHIELDED CONTACTS
SPACE FLIGHT APPLICATION
SIZE 8 REMOVABLE SHIELDED CONTACTS
SCBC
SCBM
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
STEP 1: STRIP WIRE TO INDICATED LENGTH.
STEP 2: CRIMP WIRE TO CONTACT.
TAKE CARE NOT TO:
- Damage or remove strands.
- Untwist or overtwist strands.
- Leave insulation particles on strands.
- Damage insulation.
- Trim cable.
- Slide ferrule over jacket. Insert
dielectric and center conductor
into barrel. Crimp center con-
ductor into contact.
- Butt ferrule against shoulder.
Crimp ferrule over braid.
STEP 2: SOLDER WIRE TO CONTACT.
- Trim cable. Tin center conductor.
- Slide ferrule over jacket. Insert
dielectric and center conductor into
barrel. Solder center conductor
into contact.
- Butt ferrule against shoulder.
Solder cable to barrel through hole
in ferrule. Solder cap into body.
STEP 2: SOLDER/CRIMP WIRE TO CONTACT.
- Trim cable. Tin center conductor.
- Slide ferrule over jacket. Insert
dielectric and center conductor into
barrel. Solder center conductor
into contact.
- Butt ferrule against shoulder.
Crimp ferrule over braid. Solder
cap into body.
PART
NUMBER RG CABLE
NUMBER A B C CRIMP
TOOL
✽C4101M
✽S4101M 178 B/U 0.281
(7.14) 0.250
(6.35) 0.078
(1.98) 9504-0
✽C4102M
✽S4102M 179 B/U
316 /U 0.281
(7.14) 0.250
(6.35) 0.078
(1.98) 9504-0
✽C4103M
✽S4103M 180 B/U 0.375
(9.53) 0.312
(7.92) 0.078
(1.98) 9504-0
✽C4104M
✽S4104M 58 B/U 0.375
(9.53) 0.312
(7.92) 0.078
(1.98) 9504-0
✽CC4101M 178 B/U 0.281
(7.14) 0.250
(6.35) 0.120
(3.05) 9504-14
✽CC4102M 179 B/U
316 /U 0.281
(7.14) 0.250
(6.35) 0.120
(3.05) 9504-13
✽CC4103M 180 B/U 0.375
(9.53) 0.312
(7.92) 0.120
(3.05) 9504-15
✽CC4104M 58 B/U 0.375
(9.53) 0.312
(7.92) 0.120
(3.05) 9504-15
Shielded Contact Hand Crimp Tool
See Chart above for Crimp Tool Part Numbers.
✽Contact gender is designated by M for male contacts
and F for female contacts.
Typical Part Number:
FC4101M
Insulation Braid
Dielectric
Center conductor
Ferrule
Jacket
Barrel
Solder
or crimp
Ferrule
Jacket Barrel Cap
Solder
A
BC
SCBC
SERIES
Size 20 Signal Contacts,
Crimp Removable
Size 8 Shielded and
P o w e r Crimp
Removable Contacts
Space Application
Quality Connectors
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
Space Combination Contact Subminiature-D connec-
tors, Series SCBC, are space flight application quality rec-
tangular connectors designed especially to withstand the
rigors of launch and subsequent space flight. The SCBC
Series features crimp removable Size 20 signal contacts
and Size 8 power and shielded contacts.
The materials, dimensions, and performance of the
SCBC Series conform to the requirements of DESC draw-
ing 85039 and GSFC S-311-P-405 where applicable. Th e
SCBC Series fully complies to the outgassing requirements
of ASTM E-595 and NASA-RP-1124.
The SCBC Series utilizes precision machined contacts
with the female contact featuring a “Closed-Entry” design
having a brass protective shroud.
Eleven standard combination contact variants are avail-
able, utilizing six shell sizes. All connector variants of the
SCBC Series are plug compatible with equivalent SCBM
printed board mounted or panel mounted connectors.
Nonmagnetic cable supports and jackscrew systems
are available.
Visual and mechanical inspection per MIL-DTL-24308 is
performed, additional testing is available. Contact
Technical Sales.
✽SCBC SERIES CONTACT VARIANTS
FACE VIEW OF MALE OR REAR VIEW OF FEMALE
5W1 7W2 11W1
SHELL SIZE 2
SHELL SIZE 1
SHELL SIZE 3
13W3 17W2 21W1
36W4 47W1 46W4
43W2
25W3
SHELL SIZE 4
SHELL SIZE 5 SHELL SIZE 6
✽NOTE:
Additional contact variants may
be tooled at customer request.
36
Positronic
Industries, Inc.
Positronic
Industries, Inc.
37
SCBC SERIES TECHNICAL CHARACTERISTICS
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
MATERIALS AND FINISHES:
Insulator: Glass-filled polyester per MIL-M-24519,
UL 94V-0, ASTM E-595, NASA-RP-1124,
blue color.
Contacts: Male Contacts: Precision machined
brass alloy. Female Contacts: Precision
machined high tensile copper alloy with
brass shroud; “Closed Entry” design.
Signal Contact Plating: 0.000050 inch (1.25 microns) gold over cop-
per plate.
Power Contacts: Machined of high conductivity copper
alloy for both male and female contacts.
Power Contact Plating: 0.000050 inch (1.25 microns) gold over
copper plate.
Shielded Contacts: Precision-machined copper alloy male
contacts and female contacts. Retainers
of beryllium copper.
Shielded Contact Plating: Signal Contact Plating: 0.000050 inch
(1.25 microns) gold over copper.
Shielded Body Plating: 0.000050 inch
(1.25 microns) gold over copper.
Shells: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
Mounting Spacers: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
Jackscrew Systems: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
Hoods: Brass with 0.000050 inch (1.25 microns)
gold over copper plate or aluminum with
yellow chromate conversion or black
anodize finish.
ELECTRICAL CHARACTERISTICS:
SIGNAL CONTACTS
Contact Current Rating: 7.5 amperes, nominal.
Initial Contact
Resistance: 0.008 ohms, maximum.
Proof Voltage: 1,000 V r.m.s.
POWER CONTACTS
Contact Current Rating: 10, 15, 20, 30, and 40 amperes, nominal.
Initial Contact
Resistance: 0.005 ohms, maximum.
Proof Voltage: 1,000 V r.m.s.
SHIELDED CONTACTS
Initial Contact
Resistance: 0.008 ohms, maximum.
Nominal Impedance: 50 ohms.
Insertion Loss: -0.46 dB at 1 GHz.
-1.5 dB at 2 GHz.
VSWR: 1.15 average at 1 GHz.
1.56 average at 2 GHz.
Above values measured using frequency domain techniques.
Proof Voltage: 1,000 V r.m.s.
CONNECTORS
Insulator Resistance: 5 G ohms.
Clearance and
Creepage Distance: 0.039 inch (1.0 mm), minimum.
Working Voltage: 300 V r.m.s.
Residual Magnetism: 20 Gamma, maximum.
MECHANICAL CHARACTERISTICS:
Signal Contacts,
Crimp Removable: Size 20 contact. Male Contact: 0.040
inch (1.02 mm) diameter. Female
Contact: Closed entry design with
brass shroud.
Contact Retention in Insulator: 9 lbs. (40 N). Power and shielded - 22
lbs. (98 N).
Crimp Contact
Terminations: Closed barrel crimp, wire sizes 20 AWG
(1.0 mm2) through 30 AWG (0.05 mm2).
Power Contacts,
Removable, Crimp or
Solder Terminations: Size 8 contacts. Male Contact: 0.142
inch (3.61 mm) diameter. Female
Contact: Features Large Surface Area
(L.S.A.) Closed entry design utilizing
BeCu mechanical retention member.
Male and female contacts have termina-
tions for wire sizes 8, 12, and 16 AWG.
Shielded Contacts,
Removable: See table of maximum cable sizes for
contact termination dimensions, pages
34 and 35.
Shells: Male shells may be dimpled for
EMI/ESD ground paths.
Polarization: Trapezoidally shaped shells and polar-
ized jackscrews.
Locking Systems: Jackscrews.
Mechanical Operations,
Signal Contacts: SCBC Series, 1,000 operations, closed
entry contact with 0.000050 (1.25
microns) gold plating per IEC 512-5.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55˚C to +125˚C.
Damp Heat, Steady State: 21 days.
SCBC17W2M0000G
WITH MC4101M SCBC17W2F0000G
WITH FC4101M
0.120(3.05) ±0.005 Ø Mounting Hole, two places
0.154(3.91) Ø Mounting Hole Available
0.120(3.05) ±0.010
0.032(0.81)
Total Diametral Float 0.086(2.18) ±0.005 -0.000 Ø
Mounting Hole, two places
OPTIONAL SHELL ASSEMBLY
STANDARD SHELL ASSEMBLY
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS). ALL DIMENSIONS ARE SUBJECT TO CHANGE.
SCBC7W2F0000G SCBC17W2M0000G
0.375
(9.53)
Max.
0.220
(5.59)
Max.
E
B
B1
0.220(5.59), Max.
H
G10˚ Typ.
±0.008
0.036(0.91)
±0.010
0.050(1.27)
K
M
0.375(9.53), Max. 0.120(3.05) ±0.005 Ø Mounting Hole,
two places
C
D1 D
A
TYPICAL CONNECTOR TOP VIEW
SHELL SIZE A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 G
±0.010 H
±0.010 K
±0.005 M
±0.010
SHELL SIZE 1
MALE 1.213
(30.81) 0.666
(16.92) 0.984
(24.99) 0.329
(8.36) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
SHELL SIZE 1
FEMALE 1.213
(30.81) 0.643
(16.33) 0.984
(24.99) 0.311
(7.90) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 2
MALE 1.541
(39.14) 0.994
(25.25) 1.312
(33.32) 0.329
(8.36) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
SHELL SIZE 2
FEMALE 1.541
(39.14) 0.971
(24.66) 1.312
(33.32) 0.311
(7.90) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 3
MALE 2.088
(53.04) 1.534
(38.96) 1.852
(47.04) 0.329
(8.36) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 3
FEMALE 2.088
(53.04) 1.511
(38.38) 1.852
(47.04) 0.311
(7.90) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 4
MALE 2.729
(69.32) 2.182
(55.42) 2.500
(63.50) 0.329
(8.36) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 4
FEMALE 2.729
(69.32) 2.159
(54.84) 2.500
(63.50) 0.311
(7.90) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 5
MALE 2.635
(66.93) 2.079
(52.81) 2.406
(61.11) 0.441
(11.20) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 5
FEMALE 2.635
(66.93) 2.064
(52.43) 2.406
(61.11) 0.423
(10.74) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.243
(6.17) 0.429
(10.90)
SHELL SIZE 6
MALE 2.729
(69.32) 2.212
(56.18) 2.500
(63.50) 0.503
(12.78) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.230
(5.84) 0.426
(10.82)
SHELL SIZE 6
FEMALE 2.729
(69.32) 2.189
(55.60) 2.500
(63.50) 0.485
(12.32) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.243
(6.17) 0.429
(10.90)
38
Positronic
Industries, Inc.
OPTIONAL SHELL ASSEMBLY WITH
UNIVERSAL FLOAT MOUNTS
REELS FOR AUTOMATIC FEED PNEUMATIC CRIMP TOOLS
Contacts may be supplied in plastic carriers, pack-
aged in reels holding 2,000 contacts for use with the
automatic feed pneumatic crimp tools, catalog part
number 9550-1. The same type carrier is used for both
male and female contacts.
All male and female crimp contacts can be ordered
in reels by adding letter “R” after the contact part num-
ber, such as MC6020DR-50 for a male contact and
FC6026DR-50-1202.1 for female contact.
Enlarged section of plastic contact carriers
Material: Leaded nickel copper.
Plating: 0.000050 inch (1.25 µ) gold over copper .
Part number: FC6018M Part number: MC6018M
Material: Brass.
Plating: 0.000050 inch (1.25 µ) gold over copper.
0.170
(4.32) 0.170
(4.32)
0.915
(23.24) 0.927
(23.55)
0.055 Ø
(1.40)
0.086 Ø
(2.18)
0.055 Ø
(1.40)
0.086 Ø
(2.18)
0.040 Ø
(1.02)
Brass Shroud
FEMALE CONTACT (“CLOSED ENTRY” DESIGN)
18 AWG (1.0mm2) max. MALE CONTACT
18 AWG (1.0mm2) max.
Positronic
Industries, Inc.
39
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
CLOSED CRIMP BARREL
PART
NUMBER WIRE SIZE
AWG/(mm2)AB ØC Ø
FC6020D-50-1202.1 20 / 22 / 24
(0.5/0.3/0.25) 0.538
(13.67) 0.044
(1.12) 0.066
(1.68)
FC6026D-50-1202.1 26 / 28 / 30
(0.12/0.08/0.05) 0.538
(13.67) 0.027
(0.69) 0.066
(1.68)
PART
NUMBER WIRE SIZE
AWG/(mm2)AB ØC Ø
MC6020D-50 20 / 22 / 24
(0.5/0.3/0.25) 0.550
(13.97) 0.044
(1.12) 0.066
(1.68)
MC6026D-50 26 / 28 / 30
(0.12/0.08/0.05) 0.550
(13.97) 0.027
(0.69) 0.066
(1.68)
AA
C ØC Ø
B ØB Ø
Brass Shroud
0.170
(4.32) 0.170
(4.32)
0.040 Ø
(1.02)
Crimp contacts may be supplied kitted with connector or ordered separately.
Contact Material: Leaded nickel copper.
Plating: 0.000050 inch (1.25 µ) gold over copper. Material: Brass.
Plating: 0.000050 inch (1.25 µ) gold over copper.
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
FEMALE CONTACT (“CLOSED ENTRY” DESIGN) MALE CONTACT
CRIMP REMOVABLE CONTACT CONNECTOR
SIGNAL CRIMP CONTACTS
For SCBC crimping information and crimp
tools, see pages 39, 40, 41 and 43.
CRIMPING INFORMATION FOR SND AND SCBC SERIES CRIMP SIGNAL CONTACTS
CRIMP REMOVABLE CONTACT CONNECTOR
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
USE INDICATED POSITRONIC TOOLS FOR BEST RESULTS
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Step 1: Strip wire to indicated length.
Step 2: Crimp wire to contact. For Hand Crimp Tool: - Place contact into crimping tool.
- Insert wire into contact.
- Center contact by slowly closing the
crimping tool until the crimp indenters
make contact with the crimp barrel.
- Complete the cycle of the crimping tool in
one smooth motion.
- Remove the crimped contact.
Take Care Not To: - Damage or remove strands.
- Untwist or overtwist strands.
- Leave insulation particles on strands.
- Damage insulation.
For Automatic Feed Pneumatic Crimp Tool: - Insert the wire into the contact, positioned in the
crimp tool by the plastic carrier.
- Depress the activating device of the crimping
tool to start the crimping cycle.
- Remove the crimped contact.
0.160
(4.06)
Insulation
Stranded Wire
±0.020
Strands damaged
or removed by
stripping tool.
Insulation cut
incorrectly.
Strands overtwisted.
Particles of insulation
on the stripped part
of the wire.
Wire insulation damaged.
Strands untwisted.
Examples of Stripping Faults
Correctly Stripped Wire
40
Positronic
Industries, Inc.
Positronic
Industries, Inc.
41
CRIMPING INFORMATION FOR SND AND SCBC SERIES CRIMP SIGNAL CONTACTS
CRIMP REMOVABLE CONTACT CONNECTOR
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Conductor tensile strength values are derived using silver-tin
plated copper wires.
Values may change depending upon what type of wire is used.
Wire Insulation, Typical
Crimp to meet recommended
tensile strength.
Stripped wires compressed
for improved conduction. 8 Crimp
Indents
Crimp indents too close
to inspection hole.
Strands not visible
through inspection hole.
Strands visible beyond
insulation support.
Stripped part of
the wire too long. Stripped part of the
wire too short. Crimp indents
incorrectly located.
Step 3: Inspect the crimp.
For All Tools: - Strands to be visible through the inspection hole.
- Strands not to be visible beyond the insulation support.
- Crimped contact to meet recommended conductor tensile
force shown in chart.
- Check for peeled gold and bent contacts.
Correctly Crimped Contact
Cross Section
of Correctly Crimped Contact
Examples of Crimping Faults
Positronic Recommended
Conductor Tensile Strength
Positronic Recommended Tools
WIRE SIZE
AWG/(mm2)AXIAL LOAD
POUNDS/(N)
22
(0.3) 12
(53)
26
(0.12) 5
(22)
24
(0.25) 8
(36)
28
(0.08) 3
(13)
20
(0.5) 20
(89)
30
(0.05) 1.5
(6.7)
SND AND SCBC SERIES
CRIMP TOOLS
POSITIONERS FOR
FC6020D-50-1202.1
FC6026D-50-1202.1
MC6020D-50
MC6026D-50
9507, HAND CRIMP TOOL 9502-5
9550-1, AUTOMATIC FEED,
PNEUMATIC STRIP
AND CRIMP TOOL Supplied in reels.
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
Specify the complete connector by following Steps 1 through 9.
Insert “0” when a step is not used.
ORDERING INFORMATION - CODE NUMBERING SYSTEM
Shell Size 1
5W1
Shell Size 2
7W2, 11W1
Shell Size 3
13W3, 17W2, 21W1
Shell Size 4
25W3
Shell Size 5
36W4, 43W2, 47W1
Shell Size 6
46W4
✽NOTE:
For additional information on accessories listed
in Steps 5, 6, and 7, see the Accessory Section,
pages 48-54.
STEP
STEP 1 - Basic Series
SCBC Series
STEP 2 - SCBC Series Connector Variants
STEP 3 - Connector Gender
M -Male
F -Female
STEP 4 - Contact Termination Type
0 - Connector ordered without contacts. Order Signal and Shielded
contacts separately. See pages 32, 34, and 39 for contact part
numbers. Kitted contacts supplied in sealed bags.
1 - Signal Contacts, 20 AWG - 24 AWG (0.5 mm2- 0.25 mm2).
13 - Signal Contacts, 20 AWG - 24 AWG (0.5 mm2- 0.25 mm2) with
MCC/FCC 4101M Shielded Contacts.
14 - Signal Contacts, 20 AWG - 2 4 AWG ( 0. 5 m m 2- 0.25 mm2) with
MCC/FCC 4102M Shielded Contacts.
✽ STEP 7 - Locking and Polarizing Systems
0 - None.
T - Fixed Female Jackscrews.
T2 - Fixed Female Jackscrews.
T6 - Fixed Male and Female Polarized Jackscrews.
E - Rotating Male Jackscrews.
E2 - Rotating Male Screw Locks.
E6 - Rotating Male and Female Polarized Jackscrews.
✽ STEP 6 - Hoods
0 - None.
H - Hood, Top Opening, Brass.
M - Hood, Top Opening, Aluminum, see page 52 for
complete listing of options.
STEP 8 - Shell Options
G -Gold over Copper Plate.
D -Gold over Copper Plate and Dimpled.
✽ STEP 5 - Mounting Style
0 - Mounting Hole, 0.120(3.05) Ø.
F - Float Mounts, Universal.
S2 - Swaged Spacer, 4-40 Threads, 0.125(3.18) Length.
S5 - Swaged Locknut, 4-40 Threads.
STEP 9 - Special Options
Consult Sales Department.
1 2 3 4 5 6
SCBC 7W2 M 13 0 0 E
7
D
89
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
42
Positronic
Industries, Inc.
Positronic
Industries, Inc.
43
SPACE FLIGHT APPLICATION,
COMBINATION CONTACT SUBMINIATURE-D CONNECTORS
CRIMP REMOVABLE CONTACT SERIES
SCBC
SERIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
This fast-cycling automatic feed, strip and crimp tool pro-
duces an 8 indent crimp on wire sizes 20 AWG (0.5 mm2)
through 30 AWG (0.05 mm2). SND and SCBC Series con-
tacts must be ordered on reels.
To order, specify part number 9550-1. Foot control valve
is supplied as a standard accessory.
This miniature 8 step adjustable hand crimping tool pro-
duces an 8 indent crimp configuration and will crimp wire
sizes 20 AWG (0.5 mm2) through 30 AWG (0.05 mm2).
To crimp wire size 20 AWG (0.5 mm2) through 30 AWG
(0.05 mm2), order contact positioner 9502-5. Each posi-
tioner is equipped with a data plate which gives the correct
crimp depth setting for each wire size, and must be used
with 9507 tool frame for best results when crimping SND
and SCBC Series contacts.
One end of this tool is used to insert contacts into SND and
SCBC Series connectors. The other end is used to extract
contacts. This is accomplished by sliding the extraction tip
down the wire into the connector until it bottoms against
the contact. A slight rotation while pushing will release the
contacts, which are then extracted by simultaneously
pulling on the wire.
MINIATURE STEP ADJUSTABLE TOOL
(M22520/2-01)
Part No. 9507
INSERTION/REMOVAL TOOL
(M81969/1-02)
AUTOMATIC FEED,
STRIP AND CRIMP TOOL,
PNEUMATICALLY ACTUATED
Part No. 9550-1
Space
Adapter
Series
Series SAD
Size 20 Contacts
Series SADD
Size 22 Contacts
Series SACBM
Size 20 and
Size 8 Contacts
Connector Saver
SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY
SUBMINIATURE-D CONNECTOR SAVERS
Space Adapter-D Series connectors are space flight
application connectors that function as connector savers.
The normal density SAD Series is available in five stan-
dard connector variants of 9, 15, 25, 37 and 50 contacts.
The high density SADD Series is available in six standard
connector variants of 15, 26, 44, 62, 78 and 104 contacts.
The SACBM Series is available in twenty standard combi-
nation contact variants.
Space Adapter-D Series connectors utilize precision
machined contacts for strength and durability. The female
contact features a rugged “Closed Entry” design having a
brass shroud.
The materials and finishes, as well as the technical
characteristics of the Space Adapter-D Series connec-
tors conform to MIL-DTL-24308, GSFC S-311-P-4 and
GSFC S-311-P-10.
Visual and mechanical inspection per MIL-DTL-24308
is performed, additional testing is available. Contact
Technical Sales.
SPACE ADAPTER-D SERIES TECHNICAL CHARACTERISTICS
MATERIALS AND FINISHES:
Insulator: Glass-filled DAP per ASTM-D-5948 or poly-
ester glass-filled per MIL-M-24519, UL 94V-
0, ASTM E-595, NASA-RP-1124.
Contacts: Precision machined high tensile copper
alloy with brass shrouds.
Contact Plating: 0.000050 inch (1.25 microns) gold over cop-
per plate.
Shells: Brass with 0.000050 inch (1.25 microns)
gold over copper plate.
ELECTRICAL CHARACTERISTICS:
Contact Current Rating: 40 amperes, nominal, Size 8.
7.5 amperes, nominal, Size 20.
5 amperes, nominal, Size 22.
Initial Contact Resistance: 0.008 ohms, maximum.
Proof Voltage: 1,000 V r.m.s.
Insulator Resistance: 5 G ohms.
Clearance and
Creepage Distance: 0.039 inch (1.0 mm), minimum.
Working Voltage: 300 V r.m.s.
Residual Magnetism: 20 Gamma, maximum.
MECHANICAL CHARACTERISTICS:
Fixed Contacts: Size 8 Contact: 0.142 inch (3.61 mm)
diameter. Female Contact: Features
large surface area (L.S.A.) closed entry
design utilizing BeCu mechanical reten-
tion member.
Size 20 Contact: 0.040 inch (1.02 mm)
diameter. Female Contact: Closed
entry design with brass shroud.
Size 22 Contact: 0.030 inch (0.76 mm)
diameter. Female Contact: Closed
entry design with brass shroud.
Connector Saver: Male to female.
Contact Retention: 9 lbs. (40 N).
Shells: Male shells may be dimpled for EMI/ESD
ground paths.
Polarization: Trapezoidally shaped shells.
Mechanical Operations: 1,000 operations, minimum, per IEC 512-5.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55˚C to +125˚C.
44
Positronic
Industries, Inc.
Positronic
Industries, Inc.
45
SAD9 SAD15 SAD25
SAD37 SAD50
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CONNECTOR VARIANTS
SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY
SUBMINIATURE-D CONNECTOR SAVERS
SAD
SERIES
MALE TO FEMALE CONNECTOR SAVER
SIZE 20 CONTACTS
FACE VIEW OF MALE
Typical Part Number:
SAD9M/F
AC
EK1
K
B
D
Male Contacts Female
Contacts
0.210(5.33)
0.018(0.46)
±0.008
0.036(0.91)
0.020(0.51)
Maximum Rollover
B1
D1
±0.005
0.120 (3.05) Ø
Thru Hole,
2 places
CONNECTOR
PART NUMBER A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 K
±0.005 K1
±0.005
SAD9M/F 1.213
(30.81) 0.643
(16.33) 0.666
(16.92) 0.984
(24.99) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SAD15M/F 1.541
(39.14) 0.971
(24.66) 0.994
(25.25) 1.312
(33.32) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SAD25M/F 2.088
(53.04) 1.511
(38.38) 1.534
(38.96) 1.852
(47.04) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SAD37M/F 2.729
(69.32) 2.159
(54.84) 2.182
(55.42) 2.500
(63.50) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SAD50M/F 2.635
(66.93) 2.064
(52.43) 2.079
(52.81) 2.406
(61.11) 0.423
(10.74) 0.441
(11.20) 0.605
(15.37) 0.243
(6.17) 0.230
(5.84)
CONNECTOR VARIANTS
SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY
SUBMINIATURE-D CONNECTOR SAVERS
SADD
SERIES
MALE TO FEMALE CONNECTOR SAVER
SIZE 22 CONTACTS
FACE VIEW OF MALE
Typical Part Number:
SADD15M/F
SADD15 SADD26 SADD44
SADD62 SADD78 SADD104
AC
EK1
K
B
D
Male Contacts Female
Contacts
0.210(5.33)
0.018(0.46)
±0.008
0.036(0.91)
0.020(0.51)
Maximum Rollover
B1
D1
±0.005
0.120 (3.05) Ø
Thru Hole,
2 places
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CONNECTOR
PART NUMBER A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 K
±0.005 K1
±0.005
SADD15M/F 1.213
(30.81) 0.643
(16.33) 0.666
(16.92) 0.984
(24.99) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SADD26M/F 1.541
(39.14) 0.971
(24.66) 0.994
(25.25) 1.312
(33.32) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SADD44M/F 2.088
(53.04) 1.511
(38.38) 1.534
(38.96) 1.852
(47.04) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SADD62M/F 2.729
(69.32) 2.159
(54.84) 2.182
(55.42) 2.500
(63.50) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SADD78M/F 2.635
(66.93) 2.064
(52.43) 2.079
(52.81) 2.406
(61.11) 0.423
(10.74) 0.441
(11.20) 0.605
(15.37) 0.243
(6.17) 0.230
(5.84)
SADD104M/F 2.729
(69.32) 2.189
(55.60) 2.212
(56.18) 2.500
(63.50) 0.485
(12.32) 0.503
(12.78) 0.668
(16.97) 0.243
(6.17) 0.230
(5.84)
46
Positronic
Industries, Inc.
Positronic
Industries, Inc.
47
5W1
5W5 9W4 13W3 17W2 21W1
21WA4
24W7 36W4 47W1
46W4
43W2
25W3 27W2
8W8 13W6 17W5
3W3 7W2 11W1
SHELL SIZE 2
SHELL SIZE 1
SHELL SIZE 3
SHELL SIZE 4
SHELL SIZE 5
SHELL SIZE 6
AC
EK1
K
B
D
Male Contacts Female
Contacts
0.210(5.33)
0.018(0.46)
0.036±0.008
(0.91±0.20)
0.020(0.51)
Max. rollover
B1
D1
Ø0.120±0.005
(3.05±0.13)
Thru hole,
2 places
SPACE FLIGHT APPLICATION, NORMAL AND HIGH DENSITY
SUBMINIATURE-D CONNECTOR SAVERS
SACBM
SERIES
MALE TO FEMALE CONNECTOR SAVER
SIZE 20 AND SIZE 8 CONTACTS
CONNECTOR VARIANTS
FACE VIEW OF MALE
Typical Part Number:
SACBM11W1M/F
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CONNECTOR
SIZE A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 K
±0.005 K1
±0.005
SHELL SIZE 1 1.213
(30.81) 0.643
(16.33) 0.666
(16.92) 0.984
(24.99) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SHELL SIZE 2 1.541
(39.14) 0.971
(24.66) 0.994
(25.25) 1.312
(33.32) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.233
(5.92)
SHELL SIZE 3 2.088
(53.04) 1.511
(38.38) 1.534
(38.96) 1.852
(47.04) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SHELL SIZE 4 2.729
(69.32) 2.159
(54.84) 2.182
(55.42) 2.500
(63.50) 0.311
(7.90) 0.329
(8.36) 0.494
(12.55) 0.243
(6.17) 0.230
(5.84)
SHELL SIZE 5 2.635
(66.93) 2.064
(52.43) 2.079
(52.81) 2.406
(61.11) 0.423
(10.74) 0.441
(11.20) 0.605
(15.37) 0.243
(6.17) 0.230
(5.84)
SHELL SIZE 6 2.729
(69.32) 2.189
(55.60) 2.212
(56.18) 2.500
(63.50) 0.485
(12.32) 0.503
(12.78) 0.668
(16.97) 0.243
(6.17) 0.230
(5.84)
RIVETED-ON 90˚ MOUNTING BRACKETS
AND PUSH-ON FASTENERS
ACCESSORIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
RIVETED ON RIGHT ANGLE MOUNTING BRACKETS
PUSH-ON FASTENER FOR RIVETED ON RIGHT ANGLE MOUNTING
BRACKETS
R2
DETAIL A DETAIL B
R6 R7 R8
0.225 (5.72)
0.120 (3.05) Ø
Clearance Hole
Mounting Bracket
4-40 UNC
Threads
0.015 (0.38)
0.015 (0.38) Shells
Shells Mounting Bracket
Mounting Bracket
4-40 UNC Threads
R6 has 0.120 (3.05) Ø
clearance hole.
4-40 UNC Threads
with Locknut
4-40 UNC Threads
2.5 threads in
metal, nominal.
Detail A
Detail B
Polyester Insert
Mounting Bracket
Printed Board
Printed Board
0.187
(4.75) Ø
0.110
(2.79) Ø Hole
0.131
(3.33)
4-40 UNC
Threads
SCBM17W2F5R7N0G
(shown left) SDD26F4R7N0G
(shown right)
Printed board mounting hole to be 0.123 (3.12) Ø ±0.003 for
use with push-on fastener.
Material: Beryllium copper, 0.000050 inch (1.25 µ) gold over
copper plate.
Material: Brass, 0.000050 inch (1.25 µ) gold over copper plate.
SAMPLE # PRINTED BOARD
HOLE ØINSERTION
FORCE (LBS.) RETENTION
FORCE (LBS.)
10.120 (3.05) 7-1/4 5-3/4
20.123 (3.12) 5-3/4 5-1/2
30.125 (3.18) 2-3/4 2-1/2
40.128 (3.25) 1-3/4 2-1/4
50.126 (3.20)
PLATED 1-3/4 2-1/4
48
Positronic
Industries, Inc.
Positronic
Industries, Inc.
49
SWAGED SPACERS
(S2)
SWAGED SPACER
(S)
SWAGED LOCKNUT
(S5)
SWAGED SPACER WITH PUSH-ON FASTENER
(S6)
Material: Brass, 0.000050 inch (1.25 µ) gold over copper plate.
Material: Phosphor bronze, 0.000050 inch (1.25
µ
) gold over copper plate.
4-40 UNC
Threads
0.015 (0.38)
4-40 UNC
Threads,
Typical
Printed Board
A
0.187
(4.75)
4-40 UNC
Threads
0.015 (0.38) A
0.187
(4.75)
Material: Brass, 0.000050 inch (1.25 µ) gold over copper plate. Polyester insert.
Material: Brass, 0.000050 inch (1.25 µ) gold over copper plate.
0.015 (0.38) Typical 0.125 (3.18)
0.180
(4.57)
0.115 (2.92)
0.055 (1.40)
Panel
0.015 (0.38)
Polyester Insert
4-40 UNC
Threads. 2.5
threads in metal,
nominal.
Panel
0.187
(4.75)
Printed board mounting hole to
be 0.123 (3.12) Ø ±0.003 for use
with push-on fastener.
SWAGED SPACERS, LOCKNUTS, AND
SWAGED SPACERS WITH PUSH-ON FASTENERS
ACCESSORIES
CONNECTOR
SERIES A
SND 0.225
(5.72)
SCBM 0.250
(6.35)
SDD 0.375
(9.53)
CONNECTOR
SERIES A
SND 0.225
(5.72)
SCBM 0.250
(6.35)
SDD 0.375
(9.53)
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
RIGHT ANGLE METAL MOUNTING BRACKET (B3)
RIGHT ANGLE METAL MOUNTING BRACKET USED WITH R2, R6, R7
AND R8RIVETED-ON BRACKET ASSEMBLIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Material: Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
Material: Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
✽ 0.062 (1.57) thick for Size 104 SDD Series.
✽ 0.062 (1.57) thick for Size 104 SDD Series.
A
B
DC
0.125
(3.18) Ø
0.040
(1.02) Thick ✽
0.220
(5.59)
0.030
(0.76)
Tap 4-40
UNC-2B
0.107
(2.72)
0.060
(1.52)
0.275
(6.99)
0.063
(1.60) R.
0.040
(1.02) Thick ✽
0.063
(1.60) R.
0.125
(3.18) Ø
0.220
(5.59)
B
B
DC
AAB
A
PART NO. STYLE A B C D SIZE SCBM SND SDD
4535-2-0 10.324
(8.23) 0.484
(12.29) 0.244
(6.20) 0.358
(9.09) 9 - 37 5, 55,
57 5
4535-3-0 10.380
(9.65) 0.594
(15.09) 0.303
(7.70) 0.417
(10.59) 50 5, 55,
57 5
4535-8-0 20.405
(10.29) 0.522
(13.26) 0.246
(6.25) 0.358
(9.09) 9 - 37 7, 75,
77 42
4535-9-0 20.455
(11.56) 0.572
(14.53) 0.303
(7.70) 0.414
(10.52) 50 7, 75,
77 42
4535-62-0 20.614
(15,60) 0.731
(18,57) 0.334
(8,48) 0.445
(11,30) 104 4
STYLE 2 STYLE 3
STYLE 1
PART NO. A B C D SIZE SCBM SND SDD
4535-2-1 0.339
(8.61) 0.456
(11.58) 0.246
(6.25) 0.358
(9.09) 9 - 37 5, 55,
57 5
4535-3-1 0.395
(10.03) 0.512
(13.00) 0.303
(7.70) 0.414
(10.52) 50 5, 55,
57 5
4535-8-1 0.420
(10.67) 0.537
(13.64) 0.246
(6.25) 0.358
(9.09) 9 - 37 7, 75,
77 42
4535-9-1 0.470
(11.94) 0.587
(14.91) 0.303
(7.70) 0.414
(10.52) 50 7, 75,
77 42
4535-34-1 0.528
(13.41) 0.645
(16.38) 0.246
(6.25) 0.358
(9.09) 15 - 62 4
4535-35-1 0.573
(14.55) 0.690
(17.53) 0.303
(7.70) 0.414
(10.52) 78 4
4535-62-1 0.614
(15.60) 0.731
(18.57) 0.334
(8.48) 0.445
(11.30) 104 4
NOTE: Sold only as part of a connector assembly.
RIGHT ANGLE METAL MOUNTING BRACKETS
ACCESSORIES
4535-5-0 30.554
(14.07) 0.739
(18.77) 0.244
(6.20) 0.358
(9.09) 15 - 62 4
4535-6-0 30.604
(15.34) 0.800
(20.32) 0.303
(7.70) 0.417
(10.59) 78 4
NOTE: Sold only as part of a connector assembly.
50
Positronic
Industries, Inc.
Positronic
Industries, Inc.
51
Material: Brass, 0.000050 inch (1.25 µ) gold over copper plate.
METAL HOOD (H)
PART NO. A B C D MAX. E F G H MAX.
SND15000H0G 1.531
(38.88) 0.492
(12.50) 1.312
(33.32) 0.578
(14.68) 0.713
(18.11) 0.312
(7.92) 0.750
(19.05) 1.219
(30.96)
SND25000H0G 2.078
(52.78) 0.492
(12.50) 1.852
(47.04) 0.578
(14.68) 1.000
(25.40) 0.312
(7.92) 1.000
(25.40) 1.532
(38.91)
SND37000H0G 2.718
(69.03) 0.492
(12.50) 2.500
(63.50) 0.578
(14.68) 1.375
(34.93) 0.312
(7.92) 1.000
(25.40) 1.532
(38.91)
SND50000H0G 2.625
(66.68) 0.601
(15.27) 2.406
(61.11) 0.687
(17.45) 1.406
(35.71) 0.406
(10.31) 1.125
(28.58) 1.657
(42.09)
0.136
(3.45) Ø
A
AA
B
BB
C
G
H Max.
D
E
F
THREADED POST
(P)
Material: Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
0.187
(4.75)
L
4-40 UNC Threads
THREADED POST
AND METAL HOOD
ACCESSORIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
CONNECTOR
SERIES L
SND 0.225
(5.72)
SCBM 0.250
(6.35)
SDD 0.375
(9.53)
0.125(3.18)
Rear
Grommet
Material: Silicon rubber.
Consult factory for ordering information.
CONNECTOR
VARIANTS A B
90.630 (16.00) 0.284 (7.21)
15 0.960 (24.38) 0.284 (7.21)
25 1.504 (38.21) 0.284 (7.21)
CONNECTOR
VARIANTS A B
15 0.630 (16.00) 0.284 (7.21)
26 0.960 (24.38) 0.284 (7.21)
44 1.504 (38.21) 0.284 (7.21)
37 2.146 (54.51) 0.284 (7.21)
50 2.054 (52.17) 0.396 (10.06)
REAR GROMMETS
62 2.146 (54.51) 0.284 (7.21)
78 2.054 (52.17) 0.396 (10.06)
Prevent exposure of
bare wires during
cable flexing.
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
ALUMINUM HOOD WITH
ROTATING MALE OR FEMALE JACKSCREWS
TYPICAL
INSERTS
NOTE: Inserts are not supplied
with hood and must be
ordered separately.
Consult the Factory for part
number completion based upon
Customer requirements.
Material: Hood - Aluminum per QQ-A-225, yellow chromate conversion
per MIL-C-5541 or black anodize per MIL-A-8625 optional.
Hardware - Non-magnetic stainless steel per QQ-S-763, passi-
vated per QQ-P-35, or brass per QQ-B-626 with 0.000050
(1.27µ) gold plate over copper per MIL-G-45204 optional.
EMI/RFI METAL HOOD (M)
FOR SPACE APPLICATION SUBMINIATURE-D CONNECTORS
HOOD ACCESSORIES PART NUMBERS
HARDWARE OPTIONS YELLOW CHROMATE
CONVERSION HOOD WITH
STAINLESS STEEL HARDWARE
YELLOW CHROMATE
CONVERSION HOOD WITH
COPPER ALLOY HARDWARE
BLACK ANODIZED HOOD
WITH STAINLESS STEEL
HARDWARE
BLACK ANODIZED HOOD
WITH COPPER ALLOY
HARDWARE
MALE ROTATING
JACKSCREWS D✽000M00 D✽000MG00 D✽000MB00 D✽000MC00
FEMALE ROTATING
JACKSCREWS D✽000M700 D✽000M7G00 D✽000M7B00 D✽000M7C00
ONE (1) MALE ROTATING
JACKSCREW AND ONE (1)
FEMALE ROTATING
JACKSCREW
D✽000M600 D✽000M6G00 D✽000M6B00 D✽000M6C00
( ✽) - DESIGNATES CONNECTOR SIZE
PART
NUMBER A B C CABLE OPENING,
MAX.
D9000✽00 1.397
(35.48) 1.750
(44.45) 0.630
(16.00) Ø
0.375
(9.53)
D15000✽00 1.725
(43.82) 1.750
(44.45) 0.630
(16.00) Ø
0.375
(9.53)
D25000✽00 2.265
(57.53) 1.750
(44.45) 0.630
(16.00) Ø
0.450
(11.43)
D37000✽00 2.913
(73.99) 1.750
(44.45) 0.630
(16.00) Ø
0.450
(11.43)
D50000✽00 2.819
(71.60) 1.750
(44.45) 0.740
(18.80) Ø
0.550
(13.97)
D104000✽00 2.913
(73.99) 1.750
(44.45) 0.803
(20.40) Ø
0.625
(15.88)
( ✽) - DESIGNATES HOOD ACCESSORIES OPTION
Cable Opening
A
B
C
Rotating Male or Female
Jackscrews, 4-40 UNC Threads
Typical Part Number:
(FOR HOOD ASSEMBLY)
D25000M00
Typical Part Number:
(FOR CABLE ENTRY INSERT)
4595 - ✽✽✽ - ✽✽✽ - ✽✽
EMI/RFI METAL HOODS
ACCESSORIES
52
Positronic
Industries, Inc.
POSITRONIC
INDUSTRIES
Positronic
Industries, Inc.
53
JACKSCREW SYSTEMS
POLARIZED JACKSCREW SYSTEMS
EE2
T✽
T6 E6
CODE A
T0.437
(11.10)
T2 0.500
(12.70) 0.198
(5.03)
0.250
(6.35)
B
FIXED FEMALE
JACKSCREWS
FIXED MALE AND
FEMALE JACKSCREWS ROTATING MALE AND
FEMALE JACKSCREWS
ROTATING MALE
JACKSCREWS
ROTATING
MALE SCREW
LOCKS
Jackscrew Material: Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
0.647
(16.44) 0.437
(11.10)
0.250
(6.35)
4-40 UNC
Threads
4-40 UNC
Threads
4-40 UNC
Threads
Fixed
Female
Jackscrews
Rotating Male
Jackscrews
AB
Rotating Male
Jackscrews
0.655
(16.64)
0.682
(17.32)
0.177
(4.46)
0.150
(3.81)
0.220
(5.59)
0.445
(11.30)
0.436
(11.07)
0.194
(4.93)
Rotating Male
Jackscrew with
4-40 UNC
Threads
Position 1 for
Male Connector
Position 1 for
Male Connector
Position 1 for
Female Connector
Position 1 for
Female Connector
Rotating Female
Jackscrew with
4-40 UNC
Threads
Fixed Male
Jackscrew with
4-40 UNC
Threads
Fixed Female
Jackscrew
with 4-40 UNC
Threads
Material: Brass, 0.000050
inch (1.25 µ) gold over
copper plate.
Material: Brass, 0.000050
inch (1.25 µ) gold over
POLARIZED AND NON-POLARIZED JACKSCREW SYSTEMS
ACCESSORIES
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE.
Material: Screw - Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
U-Clip - Brass, 0.000050 inch (1.25 µ)
gold over copper plate.
NOTE: Stainless steel Jackscrews are available.
Consult factory for ordering information.
IN-LINE CRIMP SPLICE
AND PROTECTIVE COVER
ACCESSORIES
IN-LINE CRIMP SPLICE
PART
NUMBER A
±0.015 B
±0.005 B1
±0.005 C
±0.005 D
±0.005 D1
±0.005 E
±0.015 G
±0.010 H
±0.010 K
±0.005 M
±0.010
PSK633-9MG✽1.213
(30.81) 0.666
(16.92) 0.984
(24.99) 0.329
(8.36) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
PSK633-9FG✽1.213
(30.81) 0.643
(16.33) 0.984
(24.99) 0.311
(7.90) 0.494
(12.55) 0.759
(19.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
PSK633-15MG✽1.541
(39.14) 0.994
(25.25) 1.312
(33.32) 0.329
(8.36) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.233
(5.92) 0.422
(10.72)
PSK633-15FG✽1.541
(39.14) 0.971
(24.66) 1.312
(33.32) 0.311
(7.90) 0.494
(12.55) 1.083
(27.51) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
PSK633-25MG✽2.088
(53.04) 1.534
(38.96) 1.852
(47.04) 0.329
(8.36) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
PSK633-25FG✽2.088
(53.04) 1.511
(38.38) 1.852
(47.04) 0.311
(7.90) 0.494
(12.55) 1.625
(41.28) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
PSK633-37MG✽2.729
(69.32) 2.182
(55.42) 2.500
(63.50) 0.329
(8.36) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.230
(5.84) 0.426
(10.82)
PSK633-37FG✽2.729
(69.32) 2.159
(54.84) 2.500
(63.50) 0.311
(7.90) 0.494
(12.55) 2.272
(57.71) 0.422
(10.72) 0.243
(6.17) 0.429
(10.90)
PSK633-50MG✽2.635
(66.93) 2.079
(52.81) 2.406
(61.11) 0.441
(11.20) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.230
(5.84) 0.426
(10.82)
PSK633-50FG✽2.635
(66.93) 2.064
(52.43) 2.406
(61.11) 0.423
(10.74) 0.605
(15.37) 2.178
(55.32) 0.534
(13.56) 0.243
(6.17) 0.429
(10.90)
PSK633-104MG✽2.729
(69.32) 2.212
(56.18) 2.500
(63.50) 0.503
(12.78) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.230
(5.84) 0.426
(10.82)
PSK633-104FG✽2.729
(69.32) 2.189
(55.60) 2.500
(63.50) 0.485
(12.32) 0.668
(16.97) 2.302
(58.47) 0.596
(15.14) 0.243
(6.17) 0.429
(10.90)
PART
NUMBER WIRE SIZE
AWG/(mm2)L A B
PSK43637-✽16-20 AWG
(1.5/0.5 mm2)0.575
(14.61) 0.066
(1.68) 0.101
(2.57)
PSK43638-✽12-18 AWG
(4.0-1.0 mm2)0.577
(14.66) 0.097
(2.46) 0.150
(3.81)
EMI/RFI PROTECTIVE COVER
Materials:
Splice: Copper alloy, 0.000050
(1.25 µ) gold over copper.
Sleeve: Shrink-fit polyvinylidene
fluoride.
Material: Brass, 0.000050
(1.25 µ) gold
over copper.
Ø0.120±0.005
(3.05±0.13)
Two places 0.050±0.010(1.27±0.25)
0.036±0.008(0.91±0.20)
CONNECTOR
VARIANT SIZES
9 M/15 M
9 F/15 F
15 M/26 M
15 F/26 F
25 M/44 M
25 F/44 F
37 M/62 M
37 F/62 F
50 M/78 M
50 F/78 F
– /104 M
– /104 F
DIMENSIONS ARE IN INCHES (MILLIMETERS).
ALL DIMENSIONS ARE SUBJECT TO CHANGE. 54
Positronic
Industries, Inc.
✽: To order crimp splice with insu-
lating sleeve, add “-W” suffix to part
number. To order without sleeve,
add “-N” suffix.
✽: To order protective
cover with E2 rotating male
screw locks (see page 53),
insert “N” into the last digit
of part number. Omit this
digit if thread locks are not
required.
Consult factory for crimp tool
part number.
PSK43636-✽20-26 AWG
(0.5/0.12 mm2)0.500
(12.70) 0.045
(1.14) 0.076
(1.93)
Positronic
Industries, Inc.
55
311P10-17P-B-12 SCBM17W5M2000G-1082.24
311P10-17P-B-15 SCBM17W5M20200G-1082.24
311P10-17S-B-12 SCBM17W5F2000G-1082.24
311P10-17S-B-15 SCBM17W5F20200G-1082.24
311P10-18P-B-12 SCBM21WA4M2000G-1082.24
311P10-18P-B-15 SCBM21WA4M20200G-1082.24
311P10-18S-B-12 SCBM21WA4F2000G-1082.24
311P10-18S-B-15 SCBM21WA4F20200G-1082.24
311P10-20P-B-12 SCBM25W3M2000G-1082.24
311P10-20P-B-15 SCBM25W3M20200G-1082.24
311P10-20S-B-12 SCBM25W3F2000G-1082.24
311P10-20S-B-15 SCBM25W3F20200G-1082.24
311P10-21P-B-12 SCBM27W2M2000G-1082.24
311P10-21P-B-15 SCBM27W2M20200G-1082.24
311P10-21S-B-12 SCBM27W2F2000G-1082.24
311P10-21S-B-15 SCBM27W2F20200G-1082.24
311P10-22P-B-12 SCBM24W7M2000G-1082.24
311P10-22P-B-15 SCBM24W7M20200G-1082.24
311P10-22S-B-12 SCBM24W7F2000G-1082.24
311P10-22S-B-15 SCBM24W7F20200G-1082.24
311P10-23P-B-12 SCBM36W4M2000G-1082.24
311P10-23P-B-15 SCBM36W4M20200G-1082.24
311P10-23S-B-12 SCBM36W4F2000G-1082.24
311P10-23S-B-15 SCBM36W4F20200G-1082.24
311P10-24P-B-12 SCBM43W2M2000G-1082.24
311P10-24P-B-15 SCBM43W2M20200G-1082.24
311P10-24S-B-12 SCBM43W2F2000G-1082.24
311P10-24S-B-15 SCBM43W2F20200G-1082.24
311P10-25P-B-12 SCBM47W1M2000G-1082.24
311P10-25P-B-15 SCBM47W1M20200G-1082.24
311P10-25S-B-12 SCBM47W1F2000G-1082.24
311P10-25S-B-15 SCBM47W1F20200G-1082.24
311P10-1P-C-12 SND9M2000G-1082.24
311P10-1P-C-15 SND9M20200G-1082.24
311P10-1S-C-12 SND9F2000G-1082.24
311P10-1S-C-15 SND9F20200G-1082.24
311P10-2P-C-12 SND15M2000G-1082.24
311P10-2P-C-15 SND15M20200G-1082.24
311P10-2S-C-12 SND15F2000G-1082.24
311P10-2S-C-15 SND15F20200G-1082.24
311P10-3P-C-12 SND25M2000G-1082.24
311P10-3P-C-15 SND25M20200G-1082.24
311P10-3S-C-12 SND25F2000G-1082.24
311P10-3S-C-15 SND25F20200G-1082.24
311P10-4P-C-12 SND37M2000G-1082.24
311P10-4P-C-15 SND37M20200G-1082.24
311P10-4S-C-12 SND37F2000G-1082.24
311P10-4S-C-15 SND37F20200G-1082.24
311P10-5P-C-12 SND50M2000G-1082.24
311P10-5P-C-15 SND50M20200G-1082.24
311P10-5S-C-12 SND50F2000G-1082.24
311P10-5S-C-15 SND50F20200G-1082.24
311P10-6P-C-12 SCBM5W1M2000G-1082.24
311P10-6P-C-15 SCBM5W1M20200G-1082.24
311P10-6S-C-12 SCBM5W1F2000G-1082.24
311P10-6S-C-15 SCBM5W1F20200G-1082.24
311P10-7P-C-12 SCBM3W3M0000G-1082.24
311P10-7P-C-15 SCBM3W3M00200G-1082.24
311P10-7S-C-12 SCBM3W3F0000G-1082.24
311P10-7S-C-15 SCBM3W3F00200G-1082.24
311P10-8P-C-12 SCBM7W2M2000G-1082.24
311P10-8P-C-15 SCBM7W2M20200G-1082.24
311P10-8S-C-12 SCBM7W2F2000G-1082.24
311P10-8S-C-15 SCBM7W2F20200G-1082.24
GSFC
PART NUMBER POSITRONIC
PART NUMBER GSFC
PART NUMBER POSITRONIC
PART NUMBER GSFC
PART NUMBER POSITRONIC
PART NUMBER
GSFC-311-QPLD
QUALIFIED PARTS LIST DIRECTORY
GSFC
CONNECTORS
Positronic Industries offers the following listing of connectors and accessories, which are products
qualified under GSFC Specifications GSFC-S-311-P-4 and GSFC-S-311-P-10.
311P10-1P-B-12 SND9M2000G-1082.24
311P10-1P-B-15 SND9M20200G-1082.24
311P10-1S-B-12 SND9F2000G-1082.24
311P10-1S-B-15 SND9F20200G-1082.24
311P10-2P-B-12 SND15M2000G-1082.24
311P10-2P-B-15 SND15M20200G-1082.24
311P10-2S-B-12 SND15F2000G-1082.24
311P10-2S-B-15 SND15F20200G-1082.24
311P10-3P-B-12 SND25M2000G-1082.24
311P10-3P-B-15 SND25M20200G-1082.24
311P10-3S-B-12 SND25F2000G-1082.24
311P10-3S-B-15 SND25F20200G-1082.24
311P10-4P-B-12 SND37M2000G-1082.24
311P10-4P-B-15 SND37M20200G-1082.24
311P10-4S-B-12 SND37F2000G-1082.24
311P10-4S-B-15 SND37F20200G-1082.24
311P10-5P-B-12 SND50M2000G-1082.24
311P10-5P-B-15 SND50M20200G-1082.24
311P10-5S-B-12 SND50F2000G-1082.24
311P10-5S-B-15 SND50F20200G-1082.24
311P10-6P-B-12 SCBM5W1M2000G-1082.24
311P10-6P-B-15 SCBM5W1M20200G-1082.24
311P10-6S-B-12 SCBM5W1F2000G-1082.24
311P10-6S-B-15 SCBM5W1F20200G-1082.24
311P10-7P-B-12 SCBM3W3M0000G-1082.24
311P10-7P-B-15 SCBM3W3M00200G-1082.24
311P10-7S-B-12 SCBM3W3F0000G-1082.24
311P10-7S-B-15 SCBM3W3F00200G-1082.24
311P10-8P-B-12 SCBM7W2M2000G-1082.24
311P10-8P-B-15 SCBM7W2M20200G-1082.24
311P10-8S-B-12 SCBM7W2F2000G-1082.24
311P10-8S-B-15 SCBM7W2F20200G-1082.24
311P10-9P-B-12 SCBM11W1M2000G-1082.24
311P10-9P-B-15 SCBM11W1M20200G-1082.24
311P10-9S-B-12 SCBM11W1F2000G-1082.24
311P10-9S-B-15 SCBM11W1F20200G-1082.24
311P10-10P-B-12 SCBM5W5M0000G-1082.24
311P10-10P-B-15 SCBM5W5M00200G-1082.24
311P10-10S-B-12 SCBM5W5F0000G-1082.24
311P10-10S-B-15 SCBM5W5F00200G-1082.24
311P10-11P-B-12 SCBM9W4M2000G-1082.24
311P10-11P-B-15 SCBM9W4M20200G-1082.24
311P10-11S-B-12 SCBM9W4F2000G-1082.24
311P10-11S-B-15 SCBM9W4F20200G-1082.24
311P10-12P-B-12 SCBM13W3M2000G-1082.24
311P10-12P-B-15 SCBM13W3M20200G-1082.24
311P10-12S-B-12 SCBM13W3F2000G-1082.24
311P10-12S-B-15 SCBM13W3F20200G-1082.24
311P10-13P-B-12 SCBM17W2M2000G-1082.24
311P10-13P-B-15 SCBM17W2M20200G-1082.24
311P10-13S-B-12 SCBM17W2F2000G-1082.24
311P10-13S-B-15 SCBM17W2F20200G-1082.24
311P10-14P-B-12 SCBM21W1M2000G-1082.24
311P10-14P-B-15 SCBM21W1M20200G-1082.24
311P10-14S-B-12 SCBM21W1F2000G-1082.24
311P10-14S-B-15 SCBM21W1F20200G-1082.24
311P10-15P-B-12 SCBM8W8M0000G-1082.24
311P10-15P-B-15 SCBM8W8M00200G-1082.24
311P10-15S-B-12 SCBM8W8F0000G-1082.24
311P10-15S-B-15 SCBM8W8F00200G-1082.24
311P10-16P-B-12 SCBM13W6M2000G-1082.24
311P10-16P-B-15 SCBM13W6M20200G-1082.24
311P10-16S-B-12 SCBM13W6F2000G-1082.24
311P10-16S-B-15 SCBM13W6F20200G-1082.24
311P10-9P-C-12 SCBM11W1M2000G-1082.24
311P10-9P-C-15 SCBM11W1M20200G-1082.24
311P10-9S-C-12 SCBM11W1F2000G-1082.24
311P10-9S-C-15 SCBM11W1F20200G-1082.24
311P10-10P-C-12 SCBM5W5M0000G-1082.24
311P10-10P-C-15 SCBM5W5M00200G-1082.24
311P10-10S-C-12 SCBM5W5F0000G-1082.24
311P10-10S-C-15 SCBM5W5F00200G-1082.24
311P10-11P-C-12 SCBM9W4M2000G-1082.24
311P10-11P-C-15 SCBM9W4M20200G-1082.24
311P10-11S-C-12 SCBM9W4F2000G-1082.24
311P10-11S-C-15 SCBM9W4F20200G-1082.24
311P10-12P-C-12 SCBM13W3M2000G-1082.24
311P10-12P-C-15 SCBM13W3M20200G-1082.24
311P10-12S-C-12 SCBM13W3F2000G-1082.24
311P10-12S-C-15 SCBM13W3F20200G-1082.24
311P10-13P-C-12 SCBM17W2M2000G-1082.24
311P10-13P-C-15 SCBM17W2M20200G-1082.24
311P10-13S-C-12 SCBM17W2F2000G-1082.24
311P10-13S-C-15 SCBM17W2F20200G-1082.24
311P10-14P-C-12 SCBM21W1M2000G-1082.24
311P10-14P-C-15 SCBM21W1M20200G-1082.24
311P10-14S-C-12 SCBM21W1F2000G-1082.24
311P10-14S-C-15 SCBM21W1F20200G-1082.24
311P10-15P-C-12 SCBM8W8M0000G-1082.24
311P10-15P-C-15 SCBM8W8M00200G-1082.24
311P10-15S-C-12 SCBM8W8F0000G-1082.24
311P10-15S-C-15 SCBM8W8F00200G-1082.24
311P10-16P-C-12 SCBM13W6M2000G-1082.24
311P10-16P-C-15 SCBM13W6M20200G-1082.24
311P10-16S-C-12 SCBM13W6F2000G-1082.24
311P10-16S-C-15 SCBM13W6F20200G-1082.24
311P10-17P-C-12 SCBM17W5M2000G-1082.24
311P10-17P-C-15 SCBM17W5M20200G-1082.24
311P10-17S-C-12 SCBM17W5F2000G-1082.24
311P10-17S-C-15 SCBM17W5F20200G-1082.24
311P10-18P-C-12 SCBM21WA4M2000G-1082.24
311P10-18P-C-15 SCBM21WA4M20200G-1082.24
311P10-18S-C-12 SCBM21WA4F2000G-1082.24
311P10-18S-C-15 SCBM21WA4F20200G-1082.24
311P10-20P-C-12 SCBM25W3M2000G-1082.24
311P10-20P-C-15 SCBM25W3M20200G-1082.24
311P10-20S-C-12 SCBM25W3F2000G-1082.24
311P10-20S-C-15 SCBM25W3F20200G-1082.24
311P10-21P-C-12 SCBM27W2M2000G-1082.24
311P10-21P-C-15 SCBM27W2M20200G-1082.24
311P10-21S-C-12 SCBM27W2F2000G-1082.24
311P10-21S-C-15 SCBM27W2F20200G-1082.24
311P10-22P-C-12 SCBM24W7M2000G-1082.24
311P10-22P-C-15 SCBM24W7M20200G-1082.24
311P10-22S-C-12 SCBM24W7F2000G-1082.24
311P10-22S-C-15 SCBM24W7F20200G-1082.24
311P10-23P-C-12 SCBM36W4M2000G-1082.24
311P10-23P-C-15 SCBM36W4M20200G-1082.24
311P10-23S-C-12 SCBM36W4F2000G-1082.24
311P10-23S-C-15 SCBM36W4F20200G-1082.24
311P10-24P-C-12 SCBM43W2M2000G-1082.24
311P10-24P-C-15 SCBM43W2M20200G-1082.24
311P10-24S-C-12 SCBM43W2F2000G-1082.24
311P10-24S-C-15 SCBM43W2F20200G-1082.24
311P10-25P-C-12 SCBM47W1M2000G-1082.24
311P10-25P-C-15 SCBM47W1M20200G-1082.24
311P10-25S-C-12 SCBM47W1F2000G-1082.24
311P10-25S-C-15 SCBM47W1F20200G-1082.24
**311P405-21P-B-12 SCBC27W2M0000G-1082.24
**311P405-21P-B-15 SCBC27W2M00200G-1082.24
**311P405-21S-B-12 SCBC27W2F0000G-1082.24
**311P405-21S-B-15 SCBC27W2F00200G-1082.24
**311P405-22P-B-12 SCBC24W7M0000G-1082.24
**311P405-22P-B-15 SCBC24W7M00200G-1082.24
311P405-22S-B-12 SCBC24W7F0000G-1082.24
311P405-22S-B-15 SCBC24W7F00200G-1082.24
311P405-23P-B-12 SCBC36W4M0000G-1082.24
311P405-23P-B-15 SCBC36W4M00200G-1082.24
311P405-23S-B-12 SCBC36W4F0000G-1082.24
311P405-23S-B-15 SCBC36W4F00200G-1082.24
311P405-24P-B-12 SCBC43W2M0000G-1082.24
311P405-24P-B-15 SCBC43W2M00200G-1082.24
311P405-24S-B-12 SCBC43W2F0000G-1082.24
311P405-24S-B-15 SCBC43W2F00200G-1082.24
311P405-25P-B-12 SCBC47W1M0000G-1082.24
311P405-25P-B-15 SCBC47W1M00200G-1082.24
311P405-25S-B-12 SCBC47W1F0000G-1082.24
311P405-25S-B-15 SCBC47W1F00200G-1082.24
311P407-1P-B-12 SDD15M0000G-1082.24
311P407-1P-B-15 SDD15M00200G-1082.24
311P407-1S-B-12 SDD15F0000G-1082.24
311P407-1S-B-15 SDD15F00200G-1082.24
311P407-2P-B-12 SDD26M0000G-1082.24
311P407-2P-B-15 SDD26M00200G-1082.24
311P407-2S-B-12 SDD26F0000G-1082.24
311P407-2S-B-15 SDD26F00200G-1082.24
311P407-3P-B-12 SDD44M0000G-1082.24
311P407-3P-B-15 SDD44M00200G-1082.24
311P407-3S-B-12 SDD44F0000G-1082.24
311P407-3S-B-15 SDD44F00200G-1082.24
311P407-4P-B-12 SDD62M0000G-1082.24
311P407-4P-B-15 SDD62M00200G-1082.24
311P407-4S-B-12 SDD62F0000G-1082.24
311P407-4S-B-15 SDD62F00200G-1082.24
311P407-5P-B-12 SDD78M0000G-1082.24
311P407-5P-B-15 SDD78M00200G-1082.24
311P407-5S-B-12 SDD78F0000G-1082.24
311P407-5S-B-15 SDD78F00200G-1082.24
311P407-6P-B-12 SDD104M0000G-1082.24
311P407-6P-B-15 SDD104M00200G-1082.24
311P407-6S-B-12 SDD104F0000G-1082.24
311P407-6S-B-15 SDD104F00200G-1082.24
311P409-1P-B-12 SND9M0000G-1082.24
311P409-1P-B-15 SND9M00200G-1082.24
311P409-1S-B-12 SND9F0000G-1082.24
311P409-1S-B-15 SND9F00200G-1082.24
311P409-2P-B-12 SND15M0000G-1082.24
311P409-2P-B-15 SND15M00200G-1082.24
311P409-2S-B-12 SND15F0000G-1082.24
311P409-2S-B-15 SND15F00200G-1082.24
311P409-3P-B-12 SND25M0000G-1082.24
311P409-3P-B-15 SND25M00200G-1082.24
311P409-3S-B-12 SND25F0000G-1082.24
311P409-3S-B-15 SND25F00200G-1082.24
GSFC
PART NUMBER POSITRONIC
PART NUMBER GSFC
PART NUMBER POSITRONIC
PART NUMBER GSFC
PART NUMBER POSITRONIC
PART NUMBER
GSFC-311-QPLD
QUALIFIED PARTS LIST DIRECTORY
GSFC
CONNECTORS
Positronic Industries offers the following listing of connectors and accessories, which are products
qualified under GSFC Specifications GSFC-S-311-P-4 and GSFC-S-311-P-10.
311P405-6P-B-12 SCBC5W1M0000G-1082.24
311P405-6P-B-15 SCBC5W1M00200G-1082.24
311P405-6S-B-12 SCBC5W1F0000G-1082.24
311P405-6S-B-15 SCBC5W1F00200G-1082.24
311P405-7P-B-12 SCBM3W3M0000G-1082.24
311P405-7P-B-15 SCBM3W3M00200G-1082.24
311P405-7S-B-12 SCBM3W3F0000G-1082.24
311P405-7S-B-15 SCBM3W3F00200G-1082.24
311P405-8P-B-12 SCBC7W2M0000G-1082.24
311P405-8P-B-15 SCBC7W2M00200G-1082.24
311P405-8S-B-12 SCBC7W2F0000G-1082.24
311P405-8S-B-15 SCBC7W2F00200G-1082.24
311P405-9P-B-12 SCBC11W1M0000G-1082.24
311P405-9P-B-15 SCBC11W1M00200G-1082.24
311P405-9S-B-12 SCBC11W1F0000G-1082.24
311P405-9S-B-15 SCBC11W1F00200G-1082.24
311P405-10P-B-12 SCBM5W5M0000G-1082.24
311P405-10P-B-15 SCBM5W5M00200G-1082.24
311P405-10S-B-12 SCBM5W5F0000G-1082.24
311P405-10S-B-15 SCBM5W5F00200G-1082.24
**311P405-11P-B-12 SCBC9W4M0000G-1082.24
**311P405-11P-B-15 SCBC9W4M00200G-1082.24
**311P405-11S-B-12 SCBC9W4F0000G-1082.24
**311P405-11S-B-15 SCBC9W4F00200G-1082.24
311P405-12P-B-12 SCBC13W3M0000G-1082.24
311P405-12P-B-15 SCBC13W3M00200G-1082.24
311P405-12S-B-12 SCBC13W3F0000G-1082.24
311P405-12S-B-15 SCBC13W3F00200G-1082.24
311P405-13P-B-12 SCBC17W2M0000G-1082.24
311P405-13P-B-15 SCBC17W2M00200G-1082.24
311P405-13S-B-12 SCBC17W2F0000G-1082.24
311P405-13S-B-15 SCBC17W2F00200G-1082.24
311P405-14P-B-12 SCBC21W1M0000G-1082.24
311P405-14P-B-15 SCBC21W1M00200G-1082.24
311P405-14S-B-12 SCBC21W1F0000G-1082.24
311P405-14S-B-15 SCBC21W1F00200G-1082.24
311P405-15P-B-12 SCBM8W8M0000G-1082.24
311P405-15P-B-15 SCBM8W8M00200G-1082.24
311P405-15S-B-12 SCBM8W8F0000G-1082.24
311P405-15S-B-15 SCBM8W8F00200G-1082.24
**311P405-16P-B-12 SCBC13W6M0000G-1082.24
**311P405-16P-B-15 SCBC13W6M00200G-1082.24
**311P405-16S-B-12 SCBC13W6F0000G-1082.24
**311P405-16S-B-15 SCBC13W6F00200G-1082.24
**311P405-17P-B-12 SCBC17W5M0000G-1082.24
**311P405-17P-B-15 SCBC17W5M00200G-1082.24
**311P405-17S-B-12 SCBC17W5F0000G-1082.24
**311P405-17S-B-15 SCBC17W5F00200G-1082.24
311P405-18P-B-12 SCBC21WA4M0000G-1082.24
311P405-18P-B-15 SCBC21WA4M00200G-1082.24
311P405-18S-B-12 SCBC21WA4F0000G-1082.24
311P405-18S-B-15 SCBC21WA4F00200G-1082.24
311P405-20P-B-12 SCBC25W3M0000G-1082.24
311P405-20P-B-15 SCBC25W3M00200G-1082.24
311P405-20S-B-12 SCBC25W3F0000G-1082.24
311P405-20S-B-15 SCBC25W3F00200G-1082.24
311P409-4P-B-12 SND37M0000G-1082.24
311P409-4P-B-15 SND37M00200G-1082.24
311P409-4S-B-12 SND37F0000G-1082.24
311P409-4S-B-15 SND37F00200G-1082.24
311P409-5P-B-12 SND50M0000G-1082.24
311P409-5P-B-15 SND50M00200G-1082.24
311P409-5S-B-12 SND50F0000G-1082.24
311P409-5S-B-15 SND50F00200G-1082.24
G08P1 MC8022D-50-1202.4
G08S1 FC8022D-50-1202.4
G10P1 MC6020D-50-1202.4
G10S1 FC6020D-50-1202.4
*GCP1 MC4101M
*GCP2 MC4102M
*GCP3 MC4103M
*GCP4 MC4104M
*GCRP1 MC4201M
*GCRP2 MC4202M
*GCRP3 MC4203M
*GCRP4 MC4204M
*GCS1 FC4101M
*GCS2 FC4102M
*GCS3 FC4103M
*GCS4 FC4104M
*GCRS1 FC4201M
*GCRS2 FC4202M
*GCRS3 FC4203M
*GCRS4 FC4204M
*GHP6 MS4820M
*GHS6 FS4820M
*GHRP6 MS4920M
*GHRS6 FS4920M
NOTE: Items denoted by * are undergoing qualification.
Consult factory for availability of items denoted by **.
56
Positronic
Industries, Inc.
M24308/6-564 RD25F11F000-403.6
M24308/6-565 RD37F11F000-403.6
M24308/6-566 RD50F11F000-403.6
M24308/6-567 DD15F11F000-403.6
M24308/6-568 DD26F11F000-403.6
M24308/6-569 DD44F11F000-403.6
M24308/6-570 DD62F11F000-403.6
M24308/6-571 DD78F11F000-403.6
M24308/6-572 DD104F11F000-403.6
M24308/6-573 RD9F0F000-403.4
M24308/6-574 RD15F0F000-403.4
M24308/6-575 RD25F0F000-403.4
M24308/6-576 RD37F0F000-403.4
M24308/6-577 RD50F0F000-403.4
M24308/6-578 DD15F0F000-403.4
M24308/6-579 DD26F0F000-403.4
M24308/6-580 DD44F0F000-403.4
M24308/6-581 DD62F0F000-403.4
M24308/6-582 DD78F0F000-403.4
M24308/6-583 DD104F0F000-403.4
M24308/7-23 HDM9M20000-403.3
M24308/7-24 HDM15M20000-403.3
M24308/7-25 HDM25M20000-403.3
M24308/7-26 HDM37M20000-403.3
M24308/7-27 HDM50M20000-403.3
M24308/7-34 HDM9M2F000-403.4
M24308/7-35 HDM15M2F000-403.4
M24308/7-36 HDM25M2F000-403.4
M24308/7-37 HDM37M2F000-403.4
M24308/7-38 HDM50M2F000-403.4
M24308/8-335 RD9M110000-403.3
M24308/8-336 RD15M110000-403.3
M24308/8-337 RD25M110000-403.3
M24308/8-338 RD37M110000-403.3
M24308/8-339 RD50M110000-403.3
M24308/8-340 RD9M110000-403.5
M24308/8-341 RD15M110000-403.5
M24308/8-342 RD25M110000-403.5
M24308/8-343 RD37M110000-403.5
M24308/8-344 RD50M110000-403.5
M24308/8-345 DD15M110000-403.3
M24308/8-346 DD26M110000-403.3
M24308/8-347 DD44M110000-403.3
M24308/8-348 DD62M110000-403.3
M24308/8-349 DD78M110000-403.3
M24308/8-350 DD104M110000-403.3
M24308/8-351 DD15M110000-403.5
M24308/8-352 DD26M110000-403.5
M24308/8-353 DD44M110000-403.5
M24308/8-354 DD62M110000-403.5
M24308/8-355 DD78M110000-403.5
M24308/8-356 DD104M110000-403.5
M24308/8-357 RD9M00000-403.3
M24308/8-358 RD15M00000-403.3
M24308/8-359 RD25M00000-403.3
M24308/8-360 RD37M00000-403.3
MILITARY
PART NUMBER POSITRONIC
PART NUMBER MILITARY
PART NUMBER POSITRONIC
PART NUMBER MILITARY
PART NUMBER POSITRONIC
PART NUMBER
MIL-DTL-24308/MIL-C-39029/MIL-C-85049
QUALIFIED PARTS LIST DIRECTORY
QPL
CONNECTORS
Positronic HDM Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number
24308-618-79/24308-1210-85.
Positronic RD Series Hoods are Q.P.L. approved to MIL-C-85049 per test report number 85049-870-84.
Positronic DD Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number
24308-1209-85/24308-1210-85/24308-117-89.
Positronic RD Series Connectors are Q.P.L. approved to MIL-DTL-24308 per test report number
24308-211-79/24308-1210-85.
Positronic RD Series Contacts are Q.P.L. approved to MIL-C-39029 per test report number 39029-694-79.
M24308/5-34 HDM9F20000-403.3
M24308/5-35 HDM15F20000-403.3
M24308/5-36 HDM25F20000-403.3
M24308/5-37 HDM37F20000-403.3
M24308/5-38 HDM50F20000-403.3
M24308/5-56 HDM9F2F000-403.4
M24308/5-57 HDM15F2F000-403.4
M24308/5-58 HDM25F2F000-403.4
M24308/5-59 HDM37F2F000-403.4
M24308/5-60 HDM50F2F000-403.4
M24308/6-502 RD9F110000-50-403.3
M24308/6-503 RD15F110000-50-403.3
M24308/6-504 RD25F110000-50-403.3
M24308/6-505 RD37F110000-50-403.3
M24308/6-506 RD50F110000-50-403.3
M24308/6-507 RD9F110000-50-403.5
M24308/6-508 RD15F110000-50-403.5
M24308/6-509 RD25F110000-50-403.5
M24308/6-510 RD37F110000-50-403.5
M24308/6-511 RD50F110000-50-403.5
M24308/6-512 DD15F110000-50-403.3
M24308/6-513 DD26F110000-50-403.3
M24308/6-514 DD44F110000-50-403.3
M24308/6-515 DD62F110000-50-403.3
M24308/6-516 DD78F110000-50-403.3
M24308/6-517 DD104F110000-50-403.3
M24308/6-518 DD15F110000-50-403.5
M24308/6-519 DD26F110000-50-403.5
M24308/6-520 DD44F110000-50-403.5
M24308/6-521 DD62F110000-50-403.5
M24308/6-522 DD78F110000-50-403.5
M24308/6-523 DD104F110000-50-403.5
M24308/6-540 RD9F00000-403.3
M24308/6-541 RD15F00000-403.3
M24308/6-542 RD25F00000-403.3
M24308/6-543 RD37F00000-403.3
M24308/6-544 RD50F00000-403.3
M24308/6-545 DD15F00000-403.3
M24308/6-546 DD26F00000-403.3
M24308/6-547 DD44F00000-403.3
M24308/6-548 DD62F00000-403.3
M24308/6-549 DD78F00000-403.3
M24308/6-550 DD104F00000-403.3
M24308/6-551 RD9F11F000-50-403.4
M24308/6-552 RD15F11F000-50-403.4
M24308/6-553 RD25F11F000-50-403.4
M24308/6-554 RD37F11F000-50-403.4
M24308/6-555 RD50F11F000-50-403.4
M24308/6-556 DD15F11F000-50-403.4
M24308/6-557 DD26F11F000-50-403.4
M24308/6-558 DD44F11F000-50-403.4
M24308/6-559 DD62F11F000-50-403.4
M24308/6-560 DD78F11F000-50-403.4
M24308/6-561 DD104F11F000-50-403.4
M24308/6-562 RD9F11F000-403.6
M24308/6-563 RD15F11F000-403.6
M24308/8-361 RD50M00000-403.3
M24308/8-362 DD15M00000-403.3
M24308/8-363 DD26M00000-403.3
M24308/8-364 DD44M00000-403.3
M24308/8-365 DD62M00000-403.3
M24308/8-366 DD78M00000-403.3
M24308/8-367 DD104M00000-403.3
M24308/8-401 RD9M11F000-403.4
M24308/8-402 RD15M11F000-403.4
M24308/8-403 RD25M11F000-403.4
M24308/8-404 RD37M11F000-403.4
M24308/8-405 RD50M11F000-403.4
M24308/8-406 DD15M11F000-403.4
M24308/8-407 DD26M11F000-403.4
M24308/8-408 DD44M11F000-403.4
M24308/8-409 DD62M11F000-403.4
M24308/8-410 DD78M11F000-403.4
M24308/8-411 DD104M11F000-403.4
M24308/8-412 RD9M11F000-403.6
M24308/8-413 RD15M11F000-403.6
M24308/8-414 RD25M11F000-403.6
M24308/8-415 RD37M11F000-403.6
M24308/8-416 RD50M11F000-403.6
M24308/8-417 DD15M11F000-403.6
M24308/8-418 DD26M11F000-403.6
M24308/8-419 DD44M11F000-403.6
M24308/8-420 DD62M11F000-403.6
M24308/8-421 DD78M11F000-403.6
M24308/8-422 DD104M11F000-403.6
M24308/8-423 RD9M0F000-403.4
M24308/8-424 RD15M0F000-403.4
M24308/8-425 RD25M0F000-403.4
M24308/8-426 RD37M0F000-403.4
M24308/8-427 RD50M0F000-403.4
M24308/8-428 DD15M0F000-403.4
M24308/8-429 DD26M0F000-403.4
M24308/8-430 DD44M0F000-403.4
M24308/8-431 DD62M0F000-403.4
M24308/8-432 DD78M0F000-403.4
M24308/8-433 DD104M0F000-403.4
M39029/57-354 FC8522D-50
M39029/58-360 MC8522D-50
M39029/63-368 FC5020D-50
M39029/64-369 MC5020D-50
Positronic
Industries, Inc.
57
Positronic Hermetic Connector Assemblies
Positronic Industries can supply hermetic connector assemblies for use in vacuum
applications. All Positronic hermetic connectors are designed to act as feedthroughs
through the bulkhead/chamber wall. Typically both sides of the connector have mat-
ing faces, but certain contact terminations are also available per customer require-
ment. Typical configurations include:
• Standard Density D-Subminiature (Contact size 20)
• High Density D-Subminiature (Contact size 22)
• Mixed Density D-Subminiature (Contact sizes 8 and 20 in a single package)
• Circular (Variety of contact sizes and configurations)
In addition to simply providing the hermetic connector itself, Positronic can provide a
fully-assembled flange/plate according to customer specification (see above). For
more information on Positronic hermetic capabilities, please call (800) 641-4054 and
request to speak to someone about the Positronic hermetic product line.
• Leakage Rate: <10-9 mbar.l/s
• Shock and vibration resistant
• Application Specific Design
NORTH AMERICAN HEADQUARTERS
UNITED STATES, Springfield, Missouri
Factory Sales and Engineering Offices (800)641-4054
PUERTO RICO, Ponce Factory
Factory Sales and Engineering Offices (787)841-0920
MEXICO
Factory Sales and Engineering Offices (800)872-7674
CANADA
Factory Sales and Engineering Offices (800)327-8272
PACIFIC BASIN HEADQUARTERS
SINGAPORE, Asian Factory
Factory Sales and Engineering Offices 65-6842-1419
Malaysia Sales Office 65-6842-1419
Taiwan Sales Office 8862-2937-8775
China (Shanghai) Sales Office 8621-6308-3640
Japan Sales Office 8135-661-3047
*Additional Technical Agents in Australia, New Zealand, India
South Korea,Thailand, Philippines, Hong Kong and Indonesia.
EUROPEAN HEADQUARTERS
FRANCE, Auch Factory
Factory Sales and Engineering Offices 33 5 62 63 44 91
EUROPE, Direct Sales Offices
Northern France Sales Office 33 1 45 88 13 88
Southern France Sales Office 33 4 67 72 80 28
Italy Sales Office 39 2 54 116 106
Germany Sales Office 49 2351 63 47 39
EUROPE, Technical Agents
Technical Agents in Austria, Benelux, Denmark, Finland, Greece,
Ireland, Scotland, Slovenia, Spain, Sweden, Switzerland and the
United Kingdom
MIDEAST, Technical Agents
Technical Agents in Israel and Turkey
POSITRONIC INDUSTRIES, INC.
423 N Campbell Ave • PO Box 8247 • Springfield, MO 65801
Tel (417) 866-2322 • Fax (417) 866-4115 • Toll Free (800) 641-4054
info@connectpositronic.com
POSITRONIC INDUSTRIES, S.A.S.
Zone Industrielle d’Engachies • 46 Route d’Engachies • F-32020
Auch Cedex 9 • France
Telephone 05 62 63 44 91 • Telecopieur 05 62 63 51 17
contact@connectpositronic.com
POSITRONIC ASIA PTE LTD.
3014A Ubi Road 1 #06-07 • Singapore 408703
Telephone (65) 6842-1419 • Fax (65) 6842-1421
singapore@connectpositronic.com
www.connectpositronic.com
