MCX/MMBX CONTENTS PAGE MCX General .................................................................................................................. 4 Interface.................................................................................................................... 5 Characteristics ......................................................................................................... 6 Straight plugs ........................................................................................................... 7 Right angle plugs ..................................................................................................... 8 Straight jacks ............................................................................................................ 9 Straight bulkhead jacks .......................................................................................... 10 Receptacles.......................................................................................................11-12 Receptacles and in series adapters ....................................................................... 13 Panel drillings ......................................................................................................... 14 Assembly instructions .......................................................................................15-23 MMBX Introduction........................................................................................................25-26 General................................................................................................................... 27 Interface.................................................................................................................. 28 Characteristics........................................................................................................ 29 Plugs....................................................................................................................... 30 Plugs and receptacles ............................................................................................ 31 PCB receptacles..................................................................................................... 32 Receptacles and adapters...................................................................................... 33 Adapters ................................................................................................................. 34 Panel drilling and receptacles packaging ............................................................... 35 Assembly instructions .......................................................................................36-41 5-3 MCX GENERAL 50 75 DC - 6 GHz INTRODUCTION * * * * Subminiature coaxial connectors "Push-pull" snap-on mating Complies with specification CECC 22220 CEI standard 1169-36 APPLICATIONS 50 models * * Wireless communications Civil and military radio-telecommunication equipment 75 models * * Videocommunication Television broad casting The MCX series utilizes the SMB series electrical line and features a particularly simple, compact and robust interface. The MCX series is 30 % smaller than the SMB. The MCX series helps to miniaturize equipment. It lowers wiring connection costs through its full crimp and soldercrimp versions as the centre contact of the straight models can be either crimped or soldered. It optimizes PCB layouts with its range of models for PCBs including surface mount and press-fit receptacles. 5-4 MCX INTERFACE PLUG ITEM JACK mm min. inch max. min. 1 4.15 - .163 2 2.80 3.20 .110 3 2.80 5 0 6 0.15 0 A 3.40 4.12 .157 .162 2.80 .102 .110 3 2.30 2.80 .090 .110 .012 4 0.75 0.85 .029 .033 18 22 43 47 .134 .120 NOM. 5 0 18 22 47 43 3.80 3.42 3.00 .118 B .010 C 0.48 0.53 .019 .021 .079 3.60 .142 J 3.80 .150 H .150 3.48 .135 .137 1.98 F G H 0 A 0.25 2.00 max. 4.00 E F min. 2.60 C G max. 1 .047 3.05 NOM. min. inch 2 .006 1.20 mm .126 .110 0.30 7 B max. ITEM .078 3.00 .118 3.05 NOM. 3.60 3.05 NOM 3.75 .142 .148 5-5 MCX CHARACTERISTICS REQUIREMENT GENERAL SPECIFICATIONS ELECTRICAL Impedance 50 and 75 Frequency range DC - 6 GHz Typical V.S.W.R. 1 GHz 2.5 GHz 6 GHz * Straight styles .085 2.6/50/S 1.04 1.06 1.08 1.09 1.13 1.12 * Right angle styles .085 2.6/50/S 1.03 1.04 1.06 1.07 1.10 1.10 Insulation resistance 1 000 M Contact resistance (m) * centre contact * outer contact Initial 5 2.5 After environment 15 7.5 Voltage rating (V.R.M.S.) * Cable RG 196/U - RG 188A/U - .047" * O 2.6 double screen * RG 405/U - .085 At sea level 170 V rms max 335 V rms max 250 V rms max At 70.000 Ft 45 V rms max 85 V rms max 65 V rms max Dielectric withstanding voltage * Cable RG 196/U - RG 188A/U - .047" * O 2.6 double screen * RG 405/U - .085 At sea level 500 V rms max 750 V rms max 750 V rms max At 70.000 Ft 100 V rms max 100 V rms max 100 V rms max Power P = 120W at 1.8 GHz, T = 40C at sea level, VSWR = 1.1 for a straight plug MCX for O 2.6/50/D cable MECHANICAL Mechanical endurance 500 matings Engagement and separation force Engagement 14.2 lbs - 63 N max Cable retention force RG 196A/URG 188A/UO 2.6/50 double screen .047" RG 405/U-.085 Contact captivation Axial force 2.25 Lbs 10 N Separation 1.8 Lbs-8N 4.5 lbs 20 N 7.2 lbs - 32 N 11.9 lbs - 53 N 24.1 lbs - 107 N 9.7 lbs - 43 N 34.9 lbs - 155 N ENVIRONMENTAL Operating temperature -55C +155C Temperature cycling CECC 22220 paragraph 4-6-5 Thermal shock CECC 22220 paragraph 4-6-7 MIL STD 202 - method 107 condition C High temperature test CECC 22220 paragraph 4-7-2 MIL STD 202 - method 108A condition D Corrosion (salt spray) CECC 22220 paragraph 4-6-10 MIL STD 202 - method 101 condition B Vibration CECC 22220 paragraph 4-6-3 MIL STD 202 - method 204 condition D MATERIALS Bodies and male contacts Brass Interface and female centre contacts Beryllium copper Ferrules Brass Insulators PTFE PLATING Bodies Gold / BBR* Centre contacts Gold * BBR Bright Bronze Radiall Standard packaging = 100 pieces. For unit packaging add W after the P/N All dimensions are given in mm 5-6 MCX PLUGS STRAIGHT PLUGS, FULL CRIMP TYPE, FOR FLEXIBLE CABLE Cable group 2 / 50 / S 2.6 / 50 / S 2.6 / 50 / D Part number Imp. () Dimensions (mm) A R113 081 000 R113 081 020 R113 082 000 R113 082 020 50 16 R213 082 007 R213 083 007 2.55 1.1 D Captive center contact 18.2 2.95 18.3 3.25 BBR Gold M 01 yes 1.7 Finish Gold 5 3.25 75 Assembly instructions no 1.65 R113 083 020 2.6 / 75 / S C 2.95 R113 083 000 2.6 / 75 / D B BBR Gold BBR 5.8 STRAIGHT PLUGS, SOLDER TYPE, FOR SEMI-RIGID CABLE Cable group .047" .085" Part number Imp. () Dimensions (mm) A R113 051 000* R113 051 020* R113 053 000 R113 053 020* 50 B C 2 1.3 11.3 Captive center contact 2.25 Finish Gold no 3 Assembly instructions M 04 BBR Gold BBR * Upon request 5-7 MCX PLUGS RIGHT ANGLE PLUGS, CRIMP TYPE, FOR FLEXIBLE CABLE (captive center contact) Fig. 1 Cable group 2 / 50 / S 2.6 / 50 / S 2.6 / 50 / D Part number Fig. 2 Fig. Imp. () Dimensions (mm) A B R113 181 000 R113 181 020 R113 182 000 R113 182 020 1 50 8.6 11.9 2.6 / 75 / D R213 183 007 2.55 1.1 Assembly instructions BBR Gold M 05 3.25 2 75 10.6 2.95 13.3 Finish Gold 1.65 R113 183 020 R213 182 007 D 2.95 R113 183 000 2.6 / 75 / S C BBR 1.7 3.25 BBR Gold RIGHT ANGLE PLUGS, SOLDER TYPE, FOR SEMI-RIGID CABLE (captive center contact) Cable group .047" .085" Part number Imp. () Dimensions (mm) A B R113 151 000 R113 151 020* 8.5 R113 153 000 R113 153 020* 2 / 50 2.6 / 50 .085" R113 161 000 .141" R113 155 000 R113 161 020 C D 2 1.3 7 Assembly instructions Gold M 03 2.25 50 8 9.3 7 4.35 BBR Gold BBR 3 7.9 Finish Gold 2.35 M 02 3.05 M 03 BBR Gold * Upon request 5-8 MCX JACKS STRAIGHT JACKS, FULL CRIMP TYPE, FOR FLEXIBLE CABLE Fig. 1 Cable group 2 / 50 / S 2.6 / 50 / S 2.6 / 50 / D 2.6 / 75 / S 2.6 / 75 / D Part number Fig. Imp. () Fig. 2 Dimensions (mm) R113 236 000 R113 236 020 R113 240 000 1 50 B Captive center contact 2.55 1.1 no Panel drilling 3.25 R113 241 020* R213 238 007 Assembly instructions BBR M 01 1.65 75 3.25 Gold yes BBR 2.95 2 Finish (note) Gold 2.95 R113 241 000* R213 239 007 A 1.7 yes P 01 M 01 BBR (Snap mount Panel thickness 0 2.5 -0.1 ) STRAIGHT JACKS, SOLDER TYPE, FOR SEMI-RIGID CABLE Cable group .047" .085" Part number Imp. () Dimensions (mm) A R113 221 000* R113 221 020* R113 223 000 R113 223 020* 50 B C 2 1.3 11.9 Captive center contact 2.25 Finish Gold no 3 Assembly instructions M 04 BBR Gold BBR * Upon request 5-9 MCX JACKS STRAIGHT BULKHEAD JACKS, FULL CRIMP TYPE, FOR FLEXIBLE CABLE Fig. 1 Fig. 2 Dimensions (mm) Cable group 2 / 50 / S Part number R113 306 020 A R113 311 000 R113 311 020* B C Captive center contact 2.55 1.1 no Assembly instructions Panel drilling Finish Note Gold BBR 1 R113 310 020* R113 312 000* 2.6 / 50 / D Imp. () R113 306 000 R113 310 000 2.6 / 50 / S Fig. Gold 50 5 2.95 2 M 01 1.65 1 P 02 yes BBR Gold 3.25 Rear mount BBR STRAIGHT BULKHEAD JACKS, SOLDER TYPE, FOR SEMI-RIGID CABLE Cable group .047" .085" Part number Imp. () R113 301 000* R113 301 020* R113 303 000 R113 303 020* Dimensions (mm) A 5 50 2.6 B C 2 1.3 Captive center contact 2.25 Panel drilling Finish Gold no 3 Assembly instructions M 04 P 02 BBR Gold Nickel * Upon request 5-10 MCX RECEPTACLES STRAIGHT FEMALE PANEL RECEPTACLES (captive center contact) Fig. 1 Fig. 2 Fig. 3 Part number Fig. R113 402 220* 1 R113 553 000 R113 553 020 R113 554 020* Dimensions (mm) Imp. () 2 50 3 A B Panel drilling Finish Note 8.7 4.8 P 03 BBR Press-in mount 8.65 2.5 P 02 7.8 2.8 P 04 Gold BBR BBR Recessed front mount Panel mount + PCB RIGHT ANGLE FEMALE PANEL RECEPTACLES (captive center contact) Part number R113 670 000* R113 670 020* Imp. () 50 Dimensions (mm) A B C Panel drilling 14.1 9.4 2.5 P 02 Finish Gold BBR * Upon request 5-11 MCX RECEPTACLES STRAIGHT FEMALE PCB RECEPTACLES (captive center contact) Fig. 1 Part number Fig. Imp. () Fig. 2 Fig. 3 Dimensions (mm) Assembly instructions A B C 6.9 1.4 0.5 Fig. 4 Panel drilling Finish R113 423 000 R113 423 810 2 5.9 R113 424 020 4.7 Gold 0.96 SMT SMT / reel 100 pieces SMT / reel 500 pieces 4 3 10 3.6 R113 426 020 R113 427 020* SMT / reel 100 pieces 50 R113 426 000 R113 427 000 SMT / reel 500 pieces M 07 R113 424 000 R113 426 010* Note SMT / Edge-card 1 R113 423 820 R113 424 010 Fig. 5 0.98 P 05 4 4 R213 426 000* 3 R213 424 800 5 75 Short pins BBR 9 3 0.5 P 06 10 4.1 0.71 P 05 M 07 Gold BBR Gold Space saving on PCB SMT / reel 100 pieces STRAIGHT MALE PCB RECEPTACLES (captive center contact) Part number Imp. () R113 425 000* 50 Dimensions (mm) A B C Panel drilling Finish 9.6 4 0.96 P 05 Gold * Upon request 5-12 MCX RECEPTACLES AND IN SERIES ADAPTERS RIGHT ANGLE FEMALE PCB RECEPTACLES (captive center contact) Fig. 1 Part number R113 661 000 R113 661 027 Fig. Imp.() Fig. 2 Fig. 3 Dimensions (mm) A B C D 1 10 10 7 3.5 2 6.5 E Fig. 4 Assembly Panel instructions drilling M 06 P 04 Fig. 5 Finish Note Gold Press-fit PCB mount BBR SMT R113 664 000 R113 664 100 R113 664 120 R113 665 020 9.5 50 R113 665 000 M 07 10.5 3 R113 666 000 9 4 R213 664 800* 2 6.5 R213 665 000 3 10.5 R213 665 120 5 75 9 Gold SMT / reel 500 pieces 0.96 6 R113 665 147 R113 666 020 SMT / reel 100 pieces 9.4 4 P 05 2.5 P 07 3 0.5 P 06 BBR Gold Space saving pattern BBR M 07 9.5 6 4 2.5 SMT / reel 100 pieces P 05 0.83 Gold Pin in paste version Packaging: reel 100 pieces M 07 IN SERIES ADAPTERS (FEMALE - FEMALE) Part number R113 704 000 R113 704 020 Imp.() 50 Finish Gold BBR * Upon request 5-13 MCX PANEL DRILLING AND PACKAGING PANEL DRILLING P01 P02 P03 P04 P05 P06 P07 PACKAGING 5-14 MCX ASSEMBLY INSTRUCTIONS M 01 Centre contact STRIPPING DIMENSIONS Ferrule Body Heatshrink sleeve (option) Stripping dimensions (mm) Part number R113 081 000 R113 081 020 R113 082 000 R113 082 020 R113 083 000 R113 083 020 R113 236 000 R113 236 020 R113 240 000 R113 241 000 R113 241 020 R113 306 000 R213 082 007 R213 083 007 R213 238 007 R213 239 007 R113 306 020 R113 310 000 R113 310 020 R113 311 000 R113 311 020 R113 312 000 a b c e 2.5 6 10 7,5 2.3 5.5 10.3 8 1 Ferrule crimping tool Center contact crimping tool Dies included MIL standard R282 293 000 (M22520/5-01) + Dies R282 271 000 sq 0.72 R282 271 000 Hex 3.25 R282 235 003 Hex 3.25 4 - Slide the heatshrink sleeve onto the cable (option). Slide the ferrule onto the cable. Strip the cable. - Slide the cable into the body until it bottoms against insulator. - Slide the ferrule over the braid. Crimp the ferrule with crimping tool (see table). - Cut the excess of braid if necessary. Slide the sleeve over the ferrule and heatshrink it in place (option). 5 2 - Slide the centre contact on until it bottoms against the cable dielectric. Crimp the centre contact with crimping tool (see table). 6 3 - Fan the braid. 5-15 MCX ASSEMBLY INSTRUCTIONS M 02 For cable .085" We recommend a thermal preconditionning of the cable Part number Mounting tool Positioner Assembly jig R113 161 000 R113 161 020 R282 868 000 R282 864 010 R282 740 020 1 3 - Strip the cable. Clean the cable. Tin cable inner conductor. - Introduce the positioner and the cable into the connector body until contact with the body shoulder, place the sub assembly into the assembly jig and tighten it. Solder body on the cable and let assembly cool down before removing it from the jig. Clean soldering area. - Solder cable inner conductor into the centre contact. Clean soldering area. Introduce the insulator into the body. Press fit the cap. 2 - 4 - Slide mounting tool onto the body grooves. Press fit the cap turning tool handle with adapted wrench .275(AF) (cap in the same plan than square face). 5-16 MCX ASSEMBLY INSTRUCTIONS M 02 For cable 2 & 2.6/50 Part number Mounting tool R113 161 000 R113 161 020 R282 868 000 1 3 - For the 2/50 cable. Strip the cable. Return the braid. Strip the dielectric. Tin cable inner conductor. - For the 2.6/50 cable. Strip the cable. Tin cable inner conductor. - Introduce the insulator into the body. Press fit the cap. - Slide mounting tool onto the body grooves. Press fit the cap turning tool handle with adapted wrench .275(AF) (cap in the same plan than square face). 4 2 - Push the cable into the connector body until contact with it. Solder the cable on the connector body. Solder cable inner conductor into the centre contact. Clean soldering area. 5-17 MCX ASSEMBLY INSTRUCTIONS M 03 STRIPPING DIMENSIONS We recommend a thermal preconditionning of the cable Part number R113 151 000 R113 151 020 R113 153 000 R113 153 020 R113 155 000 Stripping length (mm) a b Mounting tool Assembly jig R282 868 000 R282 740 020 Crimping instructions Positioner For use R282 864 010 2.2 3.2 Option 1 R282 864 000 2.7 1 Option 2 3 - Strip the cable. Tin the centre conductor. Clean soldering area. - Solder the cable inner conductor. Clean solder area. Introduce the insulator into the body. Place the cap. 2 OPTION 1 - Introduce the positioner and the cable into the connector body until contact with the body shoulder, place the sub assembly into the assembly jig and tighten it. - Solder body on the cable and let assembly cool down before removing it from the jig. - Clean soldering area. OPTION 2 - Push the cable into the connector body until it bottoms out. - Solder the body. - Clean soldering area. 4 OPTION 1 - Slide mounting tool onto the body grooves. - Press fit the cap turning tool handle with adapted wrench .275(AF) (cap in the same plan than square face). OPTION 2 - Place the cap. - Press cap flush or slightly below surface of body assembly. 5-18 MCX ASSEMBLY INSTRUCTIONS M 04 STRIPPING DIMENSIONS 4.8 2.7 We recommend a thermal preconditionning of the cable Part number R113 051 000 R113 051 020 R113 053 000 R113 053 020 R113 221 000 R113 221 020 R113 223 000 R113 223 020 1 Assembly jig R113 301 000 R113 301 020 R113 303 000 R113 303 020 R282 740 020 3 - Strip the cable. - - Introduce the cable into the connector body until contact with the body shoulder. Place the sub assembly into the assembly jig with positioner MCX male and tighten it. Solder body on the cable. Let the assembly cool down before removing it from the jig. Clean solder. 2 - Tin centre contact solder pot. Solder the cable inner conductor into centre contact. Clean solder area. 5-19 MCX ASSEMBLY INSTRUCTIONS M 05 Stripping length (mm) Part number a b c R113 181 000 R113 181 020 R113 182 000 R113 182 020 R113 183 000 R113 183 020 2 3 8 R213 182 007 R213 183 007 1.7 4.2 Crimping tool Dies included MIL standard R282 293 000 (M22520/5-01) + Dies R282 271 000 R282 235 003 9.7 1 Mounting tool Operation R282 868 000 Option 1 Option 2 4 - Slide onto the cable the ferrule. Strip the cable. Tin cable inner conductor. OPTION 1 - Slide mounting tool onto the body grooves. - Press fit the cap turning tool handle with adapted wrench .275(AF) (cap in the same plan than square face). OPTION 2 - Place the cap. - Press cap flush or slightly below surface of body assembly. 2 - Fan the braid. Push connector body under the braid. Slide the ferrule on the braid (in direction F). 3 - Crimp the ferrule with crimping tool. Solder inner conductor. Introduce the insulator into the body (except for R213 connectors). 5-20 MCX ASSEMBLY INSTRUCTIONS M 06 Part number R113 661 000 R113 661 027 Mounting tool Unmounting tool Upper Lower Upper Lower R282 878 500 R282 878 523 R282 878 513 R282 878 533 1 1 - - Slide the upper tool into the machine (press). Slide the lower tool into the base. Place correctly the PCB and the connector on the lower tool. 1 1 2 2 2 - Place correctly the PCB on the lower tool. Introduce the press-fit legs into the holes of the PCB. - Push on top (100N mini per press-fit leg) until total insertion. 3 Note: the connector body must rest on the PCB. 1 2 - Place the upper tool at the back of the connector and place correctly the ejectors: * on the press-fit legs (if their length exceed the PCB thickness), * in the holes of the PCB (if not). - Press the upper tool (100N mini per press-fit leg) to remove the connector until it slide down into the lower tool. CAUTION : 2 A plated hole of the PCB can be used up to 3 times. 1 5-21 MCX ASSEMBLY INSTRUCTIONS M 07 VIDEO SHADOW Part number Part number R113 423 000 R113 423 810 R113 423 820 R113 423 000 R113 423 810 R113 423 820 Part number Part number a R113 424 000 R113 424 010 R113 424 020 R113 664 000 R113 664 100 R113 664 120 O 1.7 R213 424 800 R213 664 800 O 1.57 +0.1 0 +0.1 0 b c 1.2 0.21 1 0.63 R113 424 000 R113 424 010 R113 424 020 R213 424 800 Part number R113 664 000 R113 664 100 R113 664 120 R213 664 800 R213 665 120 Part number R213 665 120 Vaccum nozzle dimensions MCX 50 MCX 75 COPLANAR LINE Pattern and signal are on the same side. Thickness of PCB: .063 (1.6 mm). The material of PCB is the epoxy resin of glass fabrics bacs (Er = 4.8). The solder resist should be printed except for the land pattern on the PCB. 5-22 MCX ASSEMBLY INSTRUCTIONS M 07(flg) SOLDER PROCEDURE 1 3 Deposition of solder paste "Sn Ag4 Cu0.5" on mounting zone by screen printing application. We recommend a low residue flux. We advise a thickness of 150 micromm (5.850 microinch). Verify that the edges of the zone are clean. Soldering by infra-red reflow. 4 Cleaning of printed circuit boards. 2 Placement of the receptacle on the mounting zone with an automatic machine of "pick and place" type. 5 Checking of solder joints and position of the component by visual inspection. TEMPERATURE PROFILE Parameter Value Unit Temperature rising Area 1-4 C/sec Max Peak Temperature 260 C Max dwell time @260C 10 sec Min dwell time @235C 20 sec Max dwell time @235C 60 sec Temperature drop in cooloing Area -1 to -4 C/sec Max dwell time above 100C 420 sec 5-23 NOTES MMBX INTRODUCTION The new MMBXTM connector series is particularly suitable for board to board connection in second and third generation telecommunication systems (GSM, PCS, WCDMA, UMTS...). MMBXTM connectors allow a quick connection in a minimum space requirement. Frequency range is DC to 12.4 GHz. SMT connectors are totally compatible with pick and place machines. * Space saving Its small space requirement is a main advantage for applications such as board to board connections as the height is only 7 mm. * Misalignment tolerance Fig. 1 Fig. 2 Fig. 1: Moreover, these connectors allow axial misalignment of 0.6 mm with a nominal value of 6.7 mm and radial misalignment of 0.4 mm easing connectors assembly. The use of an in-series adapter permits these misalignments. Fig. 2: The maximum tilt of the in-series adapter is 8 which is equivalent to 0.7 mm max between the centre line of the in-series adapter and the centre line of the PCB receptacle. In this case, the allowed radial misalignment between the two centre lines of connectors is 0.1 mm and the chamfer still guarantee the connection. 5-25 MMBX INTRODUCTION Fig. 3: When radial misalignment is at its maximum (0.4 mm), the allowed tilt is 4.5. The distance between the centre line of the inseries adapter and the centre line of the PCB receptacle is 0.7 mm max. Fig. 3 * Series Range Receptacles and in-series adapters can be either sold separately or with the in-series adapter already inserted in the receptacle. In this case, assembly time will be reduced and you will be sure that the in-series adapter is properly inserted, as it has to be assembled perpendicularly to the receptacle. Slide-on Snap-on or Slide-on + Separately Assembled Retention between receptacle and in-series adapter is ensured by the design of the adapter. - Slide-on/Snap-on: for board to board application, all in-series adapters remain on the same side during disconnection. - Slide-on/Slide-on In addition of PCB connectors and in-series adapters, Radiall offers you a wide range of products like straight plugs, right angle plugs and between-series adapters. 5-26 MMBX GENERAL 50 DC - 12.4 GHz GENERAL * * * * * Snap-on mating Microminiature coaxial connectors Robust Surface mount receptacles Fully compatible with automated pick and place machines APPLICATIONS * * * Board to board applications Base station High density packaging PROFILE Unmated Mated 5-27 MMBX INTERFACE PCB connectors PLUG LETTER JACK mm inch LETTER mm inch min. max. min. max. A 5.00 nom. 5.00 nom. .197 nom. .197 nom. B 3.68 3.71 .145 .146 C 2.25 2.30 .088 .090 M 1.45 D 0.98 1.01 .038 .040 N 2.50 nom. 2.50 nom. .098 nom. .098 nom. E 1.85 nom. 1.85 nom. .073 nom. .073 nom. O 3.70 nom. 3.70 nom. .146 nom. .146 nom. F 2.10 nom. 2.10 nom. .083 nom. .083 nom. P 0.95 nom. 0.95 nom. .037 nom. .037 nom. .071 Q 1.85 nom. 1.85 nom. .073 nom. .073 nom. .061 .069 R 0.50 nom. 0.50 nom. .020 nom. .020 nom. S 0.10 nom. 0.10 nom. .004 nom. .004 nom. G 1.80 H 1.55 I 0.90 1.75 .035 min. max. min. max. K 0.75 nom. 0.75 nom. .029 nom. .029 nom. L 0 0 .057 In-series adapters Slide-on Snap-on LETTER mm inch LETTER mm inch T 3.70 nom. .146 nom. W 3.65 nom. .144 nom. U 0.95 nom. .037 nom. X 2.05 nom. .080 nom. V 0.70 nom. .027 nom. Z 0.80 nom. .031 nom. 1 Slotted and flared to meet electrical and mechanical requirements 2 Dimension to meet electrical and mechanical requirements 5-28 MMBX CHARACTERISTICS TEST / CHARACTERISTICS CECC 22000 VALUES / REMARKS ELECTRICAL CHARACTERISTICS Impedance 50 Frequency range DC - 12.4 GHz Typical V.S.W.R. DC - 1 GHz 1 - 2.5 GHz 2.5 - 6 GHz 2/50/S 2.6/50/S 2.6/50/D 1.05 1.05 1.05 1.06 1.06 1.06 1.10 1.10 1.10 2/50/S 2.6/50/S 2.6/50/D 1.05 1.05 1.05 1.13 1.06 1.06 1.22 1.17 1.13 * Straight connectors * Right angle connectors Insulation resistance > 1 G Dielectric withstanding voltage * (sea level) 4.4.5 500 Vrms, 50 Hz 750 Vrms, 50 Hz 2/50 2.6/50 Contact resistance 4.4.2 4.4.3 5 m 1 m Mechanical endurance 4.7.1 100 matings Engagement and separation force * Engagement * Separation 4.5.4 30 N max 8 - 30 N Contact captivation 4.5.2 10 N * * centre contact outer contact MECHANICAL CHARACTERISTICS Cable retention force 2/50 2.6/50 Vibration 58 N 110 N 4.6.3 - IEC 68-2-6 Fc MIL-STD-202, Method 204 D, condition A ENVIRONMENTAL CHARACTERISTICS Temperature range Thermal shock Moisture resistance -55, +155C 4.6.7 - IEC 68-2-14 Na 4.6.6 - IEC 68-2-3 Ca Corrosion 4.6.10 - IEC 68-2-11 Ka Vibration 4.6.3 - IEC 68-2-6 Fc MIL-STD-202, Method 107G, condition B1 MIL-STD-202, Method 106F MIL-STD-202, Method 101, condition B MIL-STD-202, Method 204D, condition A MATERIALS Centre & outer contacts Beryllium copper Bodies Brass Ferrules Copper Insulators PTFE PLATINGS Centre & outer contacts Gold / NPGR* Bodies NPGR* Ferrules NPGR* * NPGR: Nickel Phosphorous Gold Radiall Standard packaging = 100 pieces. For unit packaging add W after the P/N All dimensions are given in mm 5-29 MMBX PLUGS STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLES (male centre contact) Cable group Part Number A 2 / 50 / S R223 081 000 14.3 2.6 / 50 / S R223 082 000 2.6 / 50 / D R223 083 000 Captive centre contact Assembly instructions yes M01 14.5 STRAIGHT PLUG SOLDER TYPE FOR SEMI-RIGID CABLES (male centre contact) Cable group Part Number Captive centre contact Assembly instructions .085" R223 062 000 yes M02 RIGHT ANGLE PLUGS CRIMP TYPE FOR FLEXIBLE CABLES (male centre contact) Cable group Part Number 2 / 50 / S R223 181 000 2.6 / 50 / S R223 182 000 2.6 / 50 / D R223 183 000 Captive centre contact Assembly instructions yes M03 5-30 MMBX PLUGS AND RECEPTACLES RIGHT ANGLE PLUG SOLDER TYPE FOR SEMI-RIGID CABLES (male centre contact) Cable group Part Number Captive centre contact Assembly instructions .085" R223 162 000 yes M04 STRAIGHT PCB RECEPTACLE (male centre contact) Fig. 1 Part Number Fig. R223 434 000 1 R223 434 000W 1 R223 434 020 2 R223 434 800 1 Captive centre contact PCB R223 435 800 Assembly instructions Packaging Note bulk 100 pcs M05 yes unit bulk 100 pcs SMT tape & reel 750 pcs R223 435 000 R223 435 000W Fig. 3 Fig. 2 bulk 100 pcs 3 P01 unit tape & reel 500 pcs 5-31 MMBX PCB RECEPTACLES EDGE CARD PCB RECEPTACLES (female centre contact) Fig. 1 Fig. 2 Part Number Fig. R223 423 000 1 R223 423 010 2 Captive centre contact Assembly instructions Packaging Note yes M05 bulk 100 pcs SMT edge card STRAIGHT PCB RECEPTACLE (female centre contact) Fig. 1 Part Number R223 424 000 R223 424 000W Fig. Captive centre contact PCB 2 R223 424 800 1 R223 425 800 Packaging Note bulk 100 pcs M05 unit bulk 100 pcs SMT tape & reel 750 pcs yes R223 425 000 R223 425 000W Assembly instructions 1 R223 424 200 Fig. 3 Fig. 2 bulk 100 pcs 3 P01 unit tape & reel 500 pcs 5-32 MMBX RECEPTACLES AND ADAPTERS SCREW-ON RECEPTACLE (female centre contact) Part Number Captive centre contact Panel drilling R223 555 000 yes P03 IN SERIES ADAPTERS (male-male centre contact) Part Number Length A (mm) Note Nominal board to board R223 703 000 4.8 interface: snap - slide 6.7 R223 703 020 9.7 interface: slide - slide 11.7 Other length can be designed upon request: 6.7 mm < board to board height < 20 mm IN SERIES BULKHEAD ADAPTERS (male-male centre contact) Part Number Series PCB R223 720 020 MMBX male / MMBX male P02 5-33 MMBX ADAPTERS BETWEEN-SERIES ADAPTERS Fig. 1 Fig. 2 Fig. 3 Fig. 4 Part Number Fig. Series R191 389 100 1 MMBX male / SMA male R191 389 200 2 MMBX male / SMA female R191 389 300 3 MMBX female / SMA male R191 389 400 4 MMBX female / SMA female Packaging unit 5-34 MMBX PANEL DRILLING AND RECEPTACLES PACKAGING PANEL DRILLING P01 P02 mm inch maxi mini maxi mini A 1.4 1.2 .055 .047 B 5.16 5 .203 .197 P03 mm A inch maxi mini maxi mini 7.27 7.13 .283 .281 Threading OA M7 x 0.75 RECEPTACLES PACKAGING The tape is delivered on reels of 330 mm diameter A view Part Number Note R223 424 800 R223 434 800 Including 750 receptacles Part Number Note R223 425 800 R223 435 800 Including 500 receptacles 5-35 MMBX ASSEMBLY INSTRUCTIONS M 01 Centre contact STRIPPING DIMENSIONS Ferrule Body Heatshrink sleeve (option) Part Number 1 Stripping length (mm) Dies Dim. sq Ferrule + centre contact MIL standard R282 293 000 (M22520/5-01) + dies 7.5 0.54 - 3.3 R282 235 905 6.5 0.7 - 3.3 R282 235 906 a b c R223 081 000 1 5 R223 082 000 R223 083 000 1.5 4.5 - Slide the heatshrink onto the cable (option). Slide the ferrule onto the cable. Strip the cable. 4 5 2 - - Slide the cable into the body until it bottoms against insulator. - Slide the ferrule over the braid. Crimp the ferrule with crimping tool (see table). - Cut the excess of braid if necessary. Slide the sleeve over the ferrule and heatshrink it in place (option). Slide the centre contact on until it bottoms against the cable dielectric. Crimp the centre contact with crimping tool (see table). 6 3 - Fan the braid. 5-36 MMBX ASSEMBLY INSTRUCTIONS M 02 STRIPPING DIMENSIONS Connector body We recommand a thermal preconditioning cable. 1 Part Number Stripping length (mm) a Stripping tool Pointer gauge Soldering mounting R223 062 000 1.5 R282 051 000 R282 062 000 R282 740 000 - Strip the cable. Stripping tool (see table). Positioner (see table). Trim cable centre conductor. Trimmer: (see table). 2 - Slide cable into connector body until it contacts the body shoulder. Place sub assembly into the assembly jig (see table). Insulator bottoms against the assembly jig. Solder body onto cable. Let the assembly cool down before removing it from the jig. Clean the solder area. 5-37 MMBX ASSEMBLY INSTRUCTIONS M 03 Part Number R223 181 000 R223 182 000 R223 183 000 1 2 Body Ferrule Stripping length (mm) a b 1.5 2 c Dies Dim. sq 9.5 STRIPPING DIMENSIONS Ferrule MIL standard R282 293 000 (M22520/5-01) + dies 9 4.5 Assembly tool R282 235 905 3.3 - Slide the ferrule onto the cable. - Prepare cable according to diagram. Recommandation : to tin cable centre contact before assembling. CAUTION : do not damage braid and inner conductor of cable. - Cover Splay out braid and insert cable in connector body. Ensure that braid lies above the crimp neck. R282 235 906 3 - 4 - R282 868 000 Slide ferrule over braid and crimp as close to connector body as possible. Solder inner conductor and place cover on rear opening body. Slide assembly tool in grove. Drive cover into rear opening of body by rotating the handle of the assembly-tool. 5-38 MMBX M 04 ASSEMBLY INSTRUCTIONS STRIPPING DIMENSIONS Cap Groove R Body We recommand a thermal preconditionning cable. Part Number R223 162 000 1 - Stripping length (mm) a b 2.6 1.4 Strip the cable. Tin cable inner conductor. Extraction assembly tool R282 868 000 3 - Press fit the cap. CAP SOLDER 2 - Push the cable into the connector body until contact with it. Solder the cable on the connector body. Solder cable inner conductor into the centre contact. Clean soldering area. 4 - Slide mounting tool onto the body grooves. Press fit the cap turning tool handle with adapted wrench 7mm (cap in the same face). Hex 7/flats SOLDER 5-39 MMBX ASSEMBLY INSTRUCTIONS M 05 Part Number R223 423 000 R 223 423 010 R223 424 000 R223 424 000 W 1 2 - - R223 424 200 R223 424 800 R223 434 000 Deposit solder paste "Sn Ag4 Cu0.5" on mounting zone by screen printing application. We recommend a low residue flux. We advise a thickness of 150 microns (5.85 microinch ). Verify that the edges of the zone are clean Placement of the receptacle on the mounting zone with an automatic machine of "pick and place" type. A video camera is recommended for positioning of the component. Adhesive agents must not be used on the receptacle. R223 434 000W R223 434 020 R223 434 800 3 4 5 - This process of soldering has been tested with convection oven. Below, please find the typical profile to use. - The cleaning of printed circuit boards is not obliged. - Verification of solder joints and position of the component by visual inspection. TEMPERATURE PROFILE Parameter Value Unit Temperature rising Area 1-4 C/sec Max Peak Temperature 260 C Max dwell time @260C 10 sec Min dwell time @235C 20 sec Max dwell time @235C 60 sec Temperature drop in cooling Area - 1 to - 4 C/sec Max dwell time above 100C 420 sec 5-40 MMBX ASSEMBLY INSTRUCTIONS M 05(flg) Part Number R223 424 000 R223 424 000 W R223 424 200 R223 424 800 R223 434 000 R223 434 000W R223 434 020 R223 434 800 COPLANAR LINE Pattern and signal are on the same side. The material of PCB is epoxy resin (FR4) (Er = 4.6). The solder resist should be printed except for the land pattern on the PCB. APPLICATION 75 WITH B = 0.55 mm APPLICATION 50 WITH B = 1.2 mm PCB thickness (mm) Coplanar ligne A (mm) PCB thickness (mm) Coplanar ligne A (mm) 0.8 1.0 1.2 1.6 0.350 0.360 0.365 0.375 0.8 1.0 1.2 1.6 0.190 0.200 0.205 0.210 Part Number R223 424 000 R223 424 000 W R223 424 800 Part Number R223 434 000 R223 434 000W R223 434 800 R223 424 200 5-41 NOTES