FDMS86581 MOSFET, N-Channel, POWERTRENCH), 60 V, 30 A, 15 mW Features * * * * www.onsemi.com Typical RDS(on) = 12.5 mW at VGS = 10 V, ID = 30 A Typical QG(tot) = 13 nC at VGS = 10 V, ID = 25 A UIS Capability RoHS Compliant ELECTRICAL CONNECTION Applications * * * * DC-DC Power Supplies AC-DC Power Supplies Motor Control Load Switching D 5 4 G D 6 3 S D 7 2 S D 8 1 S N-Channel MOSFET MOSFET MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Parameter Symbol Ratings Unit VDSS Drain-to-Source Voltage 60 V VGS Gate-to-Source Voltage 20 V 30 A ID Drain Current - Continuous (VGS = 10) TC = 25C (Note 1) Pulsed Drain Current, TC = 25C See Figure 4 EAS Single Pulse Avalanche Energy (Note 2) 13.5 mJ PD Power Dissipation 50 W 0.33 W/C -55 to +175 C Derate Above 25C TJ, TSTG Operating and Storage Temperature RqJC Thermal Resistance, Junction to Case 3 C/W RqJA Maximum Thermal Resistance, Junction to Ambient (Note 3) 50 C/W Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. Current is limited by bondwire configuration. 2. Starting TJ = 25C, L = 40 mH, IAS = 26 A, VDD = 60 V during inductor charging and VDD = 0 V during time in avalanche. 3. RqJA is the sum of the junction-to-case and case-to-ambient thermal resistance, where the case thermal reference is defined as the solder mounting surface of the drain pins. RqJC is guaranteed by design, while RqJA is determined by the board design. The maximum rating presented here is based on mounting on a 1 in2 pad of 2 oz copper. (c) Semiconductor Components Industries, LLC, 2013 July, 2018 - Rev. 0 1 DD G SS S Top D D Pin 1 Bottom Power 56 (PQFN8 5x6) CASE 483AE MARKING DIAGRAM $Y&Z&3&K FDMS 86581 $Y &Z &3 &K FDMS86581 = ON Semiconductor Logo = Assembly Plant Code = Numeric Date Code = Lot Code = Specific Device Code ORDERING INFORMATION See detailed ordering and shipping information on page 2 of this data sheet. Publication Order Number: FDMS86581/D FDMS86581 PACKAGE MARKING AND ORDERING INFORMATION Device Marking Device Package Shipping FDMS86581 FDMS86581 Power 56 3000 Units/ Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ELECTRICAL CHARACTERISTICS (TJ = 25C unless otherwise noted) Parameter Symbol Test Conditions Min Typ. Max. Units OFF CHARACTERISTICS Drain-to-Source Breakdown Voltage ID = 250 mA, VGS = 0 V 60 - - V IDSS Drain-to-Source Leakage Current VDS = 60 V, VGS = 0 V TJ = 25C - - 1 A TJ = 175C (Note 4) - - 1 mA IGSS Gate-to-Source Leakage Current VGS = 20 V - - 100 nA 2.0 2.7 4.0 V TJ = 25C - 12.5 15.0 mW TJ = 175C (Note 4) - 25.1 30.1 mW - 881 - pF BVDSS ON CHARACTERISTICS VGS(th) Gate to Source Threshold Voltage VGS = VDS, ID = 250 mA RDS(on) Drain to Source On Resistance ID = 30 A, VGS = 10 V DYNAMIC CHARACTERISTICS VDS = 30 V, VGS = 0 V, f = 1 MHz Ciss Input Capacitance Coss Output Capacitance - 281 - pF Crss Reverse Transfer Capacitance - 15 - pF RG Gate Resistance f = 1 MHz - 3.1 - W Total Gate Charge VGS = 0 to 10 V, VDD = 30 V, ID = 25 A - 13 19 nC Threshold Gate Charge VGS = 0 to 2 V, VDD = 30 V, ID = 25 A - 2 - nC Qgs Gate-to-Source Gate Charge VDD = 30 V, ID = 25 A - 4 - nC Qgd Gate-to-Drain "Miller" Charge - 3 - nC - - 20 ns - 9 - ns Rise Time - 5 - ns Turn-Off Delay - 15 - ns Fall Time - 4 - ns Turn-Off Time - - 28 ns ISD = 30 A, VGS = 0 V - - 1.25 V ISD = 15 A, VGS = 0 V - - 1.2 V IF = 30 A, dlSD/dt = 100 A/ms, VDD = 48 V - 37 55 ns - 22 33 nC Qg(ToT) Qg(th) SWITCHING CHARACTERISTICS ton Turn-On Time td(on) Turn-On Delay tr td(off) tf toff VDD = 30 V, ID = 30 A, VGS = 10 V, RGEN = 6 W DRAIN-SOURCE DIODE CHARACTERISTICS VSD Source-to-Drain Diode Voltage trr Reverse-Recovery Time Qrr Reverse Recovery Charge Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 4. The maximum value is specified by design at TJ = 175C. Product is not tested to this condition in production. www.onsemi.com 2 FDMS86581 TYPICAL CHARACTERISTICS 50 1.0 ID, DRAIN CURRENT (A) POWER DISSIPATION MULTIPLIER 1.2 0.8 0.6 0.4 0.2 0.0 40 CURRENT LIMITED BY PACKAGE 30 20 10 0 0 25 50 75 100 125 150 175 0 50 TC, CASE TEMPERATURE (5C) Figure 1. Normalized Power Dissipation vs. Case Temperature 2 NORMALIZED THERMAL IMPEDANCE, ZqJC VGS = 10 V CURRENT LIMITED BY SILICON 75 100 125 150 TC, CASE TEMPERATURE (5C) 175 200 Figure 2. Maximum Continuous Drain Current vs. Case Temperature DUTY CYCLE - DESCENDING ORDER 1 0.1 0.01 10-5 D = 0.50 0.20 0.10 0.05 0.02 0.01 PDM t1 t2 NOTES: DUTY FACTOR: D = t1/t2 PEAK TJ = PDM x ZqJC x RqJC + TC SINGLE PULSE 10-4 10-3 10-2 10-1 t, RECTANGULAR PULSE DURATION (s) Figure 3. Normalized Maximum Transient Thermal Impedance www.onsemi.com 3 100 101 FDMS86581 TYPICAL CHARACTERISTICS (continued) 1000 IDM, PEAK CURRENT (A) VGS = 10 V TC = 25C FOR TEMPERATURES ABOVE 25C DERATE PEAK CURRENT AS FOLLOWS: 175 - TC I = I25 150 100 10 10-5 10-4 10-3 10-2 10-1 100 101 t, RECTANGULAR PULSE DURATION (s) Figure 4. Peak Current Capability 1000 IAS, AVALANCHE CURRENT (A) 100 ID, DRAIN CURRENT (A) 100 10 100 ms OPERATION IN THIS AREA MAY BE LIMITED BY rDS(on) 1 0.1 SINGLE PULSE TJ = MAX RATED TC = 25C 0.01 0.1 1 10 1 ms 10 ms 100 ms 100 500 If R = 0 tAV = (L)(IAS)/(1.3 x RATED BVDSS - VDD) If R 0 tAV = (L/R)In[(IAS x R)/(1.3 x RATED BVDSS - VDD) + 1] STARTING TJ = 25C 10 STARTING TJ = 150C 1 0.001 0.01 VDS, DRAIN TO SOURCE VOLTAGE (V) 0.1 1 10 tAV, TIME IN AVALANCHE (ms) NOTE: Figure 5. Forward Bias Safe Operating Area Refer to ON Semiconductor Application Notes AN7514 and AN7515. Figure 6. Unclamped Inductive Switching Capability 100 PULSE DURATION = 250 ms DUTY CYCLE = 0.5% MAX VDD = 5 V 80 IS, REVERSE DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 100 60 40 TJ = 175C 20 TJ = 25C TJ = -55C 0 3 4 5 6 7 8 9 VGS, GATE TO SOURCE VOLTAGE (V) 10 VGS = 0 V 10 TJ = 175C TJ = 25C 1 0.1 0.0 Figure 7. Transfer Characteristics 0.8 1.0 1.2 1.4 0.2 0.4 0.6 VSD, BODY DIODE FORWARD VOLTAGE (V) Figure 8. Forward Diode Characteristics www.onsemi.com 4 1.6 FDMS86581 TYPICAL CHARACTERISTICS (continued) 80 100 VGS 15 V Top 10 V 8V 7V 6V 5.5 V 5 V Bottom 250 ms PULSE WIDTH TJ = 25C 60 ID, DRAIN CURRENT (A) ID, DRAIN CURRENT (A) 100 40 20 0 0 1 2 3 4 VDS, DRAIN TO SOURCE VOLTAGE (V) 80 60 20 0 1 2 3 4 VDS, DRAIN TO SOURCE VOLTAGE (V) Figure 9. Saturation Characteristics 2.5 PULSE DURATION = 250 ms DUTY CYCLE = 0.5% MAX 120 ID = 30 A 100 80 60 TJ = 175C 40 20 0 TJ = 25C 5 6 7 8 9 VGS, GATE TO SOURCE VOLTAGE (V) 10 PULSE DURATION = 250 ms DUTY CYCLE = 0.5% MAX 2.0 1.5 ID = 30 A VGS = 10 V 1.0 0.5 -80 Figure 11. RDSON vs. Gate Voltage NORMALIZED DRAIN TO SOURCE BREAKDOWN VOLTAGE NORMALIZED GATE THRESHOLD VOLTAGE VGS = VDS ID = 250 mA 1.1 0.9 0.7 0.5 0.3 -80 -40 0 40 80 120 160 -40 0 40 80 120 160 TJ, JUNCTION TEMPERATURE (5C) 200 Figure 12. Normalized RDSON vs. Junction Temperature 2.5 1.3 5 Figure 10. Saturation Characteristics NORMALIZED DRAIN TO SOURCE ON-RESISTANCE rDS(on), DRAIN TO SOURCE ON- RESISTANCE (mW) 140 VGS 15 V Top 10 V 8V 7V 6V 5.5 V 5 V Bottom 40 0 5 250 ms PULSE WIDTH TJ = 175C 200 ID = 5 mA 2.0 1.5 1.0 0.5 -80 TJ, JUNCTION TEMPERATURE (5C) -40 0 40 80 120 160 TJ, JUNCTION TEMPERATURE (5C) 200 Figure 14. Normalized Drain to Source Breakdown Voltage vs. Junction Temperature Figure 13. Normalized Gate Threshold Voltage vs. Temperature www.onsemi.com 5 FDMS86581 TYPICAL CHARACTERISTICS (continued) VGS, GATE TO SOURCE VOLTAGE (V) CAPACITANCE (pF) 10000 1000 Ciss 100 Coss 10 1 0.1 f = 1 MHz VGS = 0 V Crss 1 10 100 10 ID = 25 A VDD = 30 V 8 VDD = 36 V VDD = 24 V 6 4 2 0 0 VDS, DRAIN TO SOURCE VOLTAGE (V) Figure 15. Capacitance vs. Drain to Source Voltage 2 4 6 8 10 Qg, GATE CHARGE (nC) 12 Figure 16. Gate Charge vs. Gate to Source Voltage www.onsemi.com 6 14 FDMS86581 PACKAGE DIMENSIONS PQFN8 5X6, 1.27P CASE 483AE ISSUE A www.onsemi.com 7 FDMS86581 POWERTRENCH is registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative FDMS86581/D