Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
LM1084 5-A Low Dropout Positive Regulators
1 Features 3 Description
The LM1084 is a regulator with a maximum dropout
1 Available in 3.3-V, 5.0-V, and Adjustable Versions of 1.5 V at 5 A of load current. The device has the
Current Limiting and Thermal Protection same pinout as TI's industry standard LM317.
Output Current 5 A Two resistors are required to set the output voltage of
Industrial Temperature Range 40°C to 125°C the adjustable output voltage version of the LM1084.
Line Regulation 0.015% (Typical) Fixed output voltage versions integrate the adjust
resistors.
Load Regulation 0.1% (Typical) The LM1084 circuit includes a zener trimmed
2 Applications bandgap reference, current limiting, and thermal
shutdown.
Post Regulator for Switching DC-DC Converter Refer to LM1085 for the 3A version, and the LM1086
High-Efficiency Linear Regulators for the 1.5A version.
Battery Chargers
Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TO-263 (3) 10.18 mm × 8.41 mm
LM1084 TO-220 (3) 14.986 mm × 10.16 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Table of Contents
7.3 Feature Description................................................... 9
1 Features.................................................................. 17.4 Device Functional Modes........................................ 11
2 Applications ........................................................... 18 Application and Implementation ........................ 13
3 Description............................................................. 18.1 Application Information............................................ 13
4 Revision History..................................................... 28.2 Typical Applications ................................................ 13
5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 20
6 Specifications......................................................... 410 Layout................................................................... 20
6.1 Absolute Maximum Ratings ...................................... 410.1 Layout Guidelines ................................................. 20
6.2 ESD Ratings ............................................................ 410.2 Layout Example .................................................... 20
6.3 Recommended Operating Conditions....................... 410.3 Thermal Considerations........................................ 20
6.4 Thermal Information.................................................. 411 Device and Documentation Support................. 22
6.5 Electrical Characteristics........................................... 511.1 Trademarks........................................................... 22
6.6 Typical Characteristics.............................................. 711.2 Electrostatic Discharge Caution............................ 22
7 Detailed Description.............................................. 911.3 Glossary................................................................ 22
7.1 Overview................................................................... 912 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram......................................... 9Information ........................................................... 22
4 Revision History
Changes from Revision F (March 2013) to Revision G Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes,Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
2Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
5 Pin Configuration and Functions
3-Pin
TO-220 Package
Top View
3-Pin
TO-263 Package
Top View
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
Adjust pin for the adjustable output voltage version. Ground pin for the fixed output voltage
ADJ/GND 1 - versions.
OUTPUT 2 O Output voltage pin for the regulator.
INPUT 3 I Input voltage pin for the regulator.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)
MIN MAX UNIT
Maximum Input to Output Voltage Differential
LM1084-ADJ 29 V
LM1084-3.3 27 V
LM1084-5.0 25 V
Power Dissipation(3) Internally Limited
Junction Temperature (TJ)(4) 150 °C
Lead Temperature 260, to 10 sec °C
Storage temperature, Tstg –65 150 °C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the
test conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) Power dissipation is kept in a safe range by current limiting circuitry. Refer to Overload Recovery.
(4) The maximum power dissipation is a function of TJ(max) ,θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Refer to Thermal
Considerations.
6.2 ESD Ratings VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)(1)
MIN MAX UNIT
Junction Temperature Range (TJ)(2)
Control Section –40 125 °C
Output Section –40 150 °C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate
conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the
test conditions, see the Electrical Characteristics.
(2) The maximum power dissipation is a function of TJ(max) ,θJA, and TA. The maximum allowable power dissipation at any ambient
temperature is PD= (TJ(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board. Refer to Thermal
Considerations.
6.4 Thermal Information LM1084
THERMAL METRIC(1) KTT NDE UNIT
3 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance 40.4 22.7
RθJC(top) Junction-to-case (top) thermal resistance 42.6 15.5
RθJB Junction-to-board thermal resistance 23.0 4.1 °C/W
ψJT Junction-to-top characterization parameter 9.8 2.1
ψJB Junction-to-board characterization parameter 22.0 4.1
RθJC(bot) Junction-to-case (bottom) thermal resistance: Control Section/Output 0.65/2.7 0.65/2.7
Section
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
6.5 Electrical Characteristics
Typicals and limits apply for TJ= 25°C unless specified otherwise.
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
VREF Reference Voltage LM1084-ADJ, IOUT = 10 mA, VIN VOUT = 3 V, 10 mA 1.238 1.250 1.262
IOUT IFULL LOAD,1.5 V (VINVOUT)25 V(3)
V
LM1084-ADJ, IOUT = 10 mA, VIN VOUT = 3 V, 10 mA
IOUT IFULL LOAD,1.5 V (VINVOUT)25 V(3), –40°C 1.225 1.250 1.270
TJ125°C
VOUT Output Voltage(3) LM1084-3.3, IOUT = 0 mA, VIN = 8 V, 0 IOUT IFULL 3.270 3.300 3.330
LOAD, 4.8 V VIN 15 V V
LM1084-3.3, IOUT = 0 mA, VIN = 8 V, 0 IOUT IFULL 3.235 3.300 3.365
LOAD, 4.8 V VIN 15 V , –40°C TJ125°C
LM1084-5.0, IOUT = 0 mA, VIN = 8 V, 0 IOUT IFULL 4.950 5.000 5.050
LOAD, 6.5 V VIN 20 V V
LM1084-5.0, IOUT = 0 mA, VIN = 8 V, 0 IOUT IFULL 4.900 5.000 5.100
LOAD, 6.5 V VIN 20 V, –40°C TJ125°C
ΔVOUT Line Regulation(4) LM1084-ADJ, IOUT = 10 mA, 1.5 V (VIN VOUT)15 V 0.015% 0.2%
LM1084-ADJ, IOUT = 10 mA, 1.5 V (VIN VOUT)15 0.035% 0.2%
V, –40°C TJ125°C
LM1084-3.3, IOUT = 0 mA, 4.8 V VIN 15 V 0.5 6 mV
LM1084-3.3, IOUT = 0 mA, 4.8 V VIN 15 V, –40°C 1.0 6
TJ125°C
LM1084-5.0, IOUT = 0 mA, 6.5 V VIN 20 V 0.5 10 mV
LM1084-5.0, IOUT = 0 mA, 6.5 V VIN 20 V, –40°C 1.0 10
TJ125°C
ΔVOUT Load Regulation(4) LM1084-ADJ, (VIN V OUT) = 3 V, 10 mA IOUT IFULL 0.1 % 0.3%
LOAD
LM1084-ADJ, (VIN V OUT) = 3 V, 10 mA IOUT IFULL 0.2% 0.4%
LOAD, –40°C TJ125°C
LM1084-3.3, VIN = 5 V, 0 IOUT IFULL LOAD 3 15 mV
LM1084-3.3, VIN = 5 V, 0 IOUT IFULL LOAD, –40°C TJ7 20
125°C
LM1084-5.0, VIN = 8 V, 0 IOUT IFULL LOAD 5 20 mV
LM1084-5.0, VIN = 8 V, 0 IOUT IFULL LOAD, –40°C TJ10 35
125°C
Dropout Voltage(5) LM1084-ADJ, 3.3, 5, 12, ΔVREF,ΔVOUT = 1%, IOUT = 5A, 1.3 1.5 V
–40°C TJ125°C
ILIMIT Current Limit LM1084-ADJ, VINVOUT = 5 V, –40°C TJ125°C 5.5 8.0 A
LM1084-ADJ, VINVOUT = 25 V, –40°C TJ125°C 0.3 0.6
LM1084-3.3, VIN = 8 V, –40°C TJ125°C 5.5 8.0 A
LM1084-5.0, VIN = 10 V, –40°C TJ125°C 5.5 8.0 A
Minimum Load LM1084-ADJ, VIN VOUT = 25 V 5 10.0 mA
Current(6)
Quiescent Current LM1084-3.3, VIN = 18 V 5.0 10.0 mA
LM1084-5.0, VIN 20 V 5.0 10.0 mA
Thermal Regulation TA= 25°C, 30 ms Pulse 0.003 0.015 %/W
(1) All limits are specified by testing or statistical analysis.
(2) Typical Values represent the most likely parametric norm.
(3) IFULLLOAD is defined in the current limit curves. The IFULLLOAD Curve defines the current limit as a function of input-to-output voltage.
Note that 30W power dissipation for the LM1084 is only achievable over a limited range of input-to-output voltage.
(4) Load and line regulation are measured at constant junction temperature, and are ensured up to the maximum power dissipation of 30W.
Power dissipation is determined by the input/output differential and the output current. ensured maximum power dissipation will not be
available over the full input/output range.
(5) Dropout voltage is specified over the full output current range of the device.
(6) The minimum output current required to maintain regulation.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Electrical Characteristics (continued)
Typicals and limits apply for TJ= 25°C unless specified otherwise.
PARAMETER TEST CONDITIONS MIN(1) TYP(2) MAX(1) UNIT
Ripple Rejection fRIPPLE = 120 Hz, = COUT = 25 µF Tantalum, IOUT = 5A dB
LM1084-ADJ, CADJ, = 25 µF, (VIN VO) = 3 V, –40°C 60 75
TJ125°C
LM1084-3.3, VIN = 6.3 V, –40°C TJ125°C 60 72 dB
LM1084-5.0, VIN = 8 V, –40°C TJ125°C 60 68 dB
Adjust Pin Current LM1084 55 µA
LM1084, –40°C TJ125°C 120
Adjust Pin Current 10 mA IOUT IFULL LOAD, 1.5 V VIN VOUT 25 V, 0.2 5 µA
Change –40°C TJ125°C
Temperature Stability –40°C TJ125°C 0.5%
Long Term Stability TA=125°C, 1000 Hrs 0.3% 1.0%
RMS Output Noise 10 Hz f10 kHz 0.003%
(% of VOUT)
6Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
6.6 Typical Characteristics
Figure 2. Short-Circuit Current
Figure 1. Dropout Voltage (VINVOUT)
Figure 4. LM1084-ADJ Ripple Rejection
Figure 3. Load Regulation
Figure 5. LM1084-ADJ Ripple Rejection vs Current Figure 6. Temperature Stability
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Typical Characteristics (continued)
Figure 8. LM1084-ADJ Load Transient Response
Figure 7. Adjust Pin Current
Figure 10. Maximum Power Dissipation
Figure 9. LM1084-ADJ LineTransient Response
8Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
7 Detailed Description
7.1 Overview
A basic functional diagram for the LM1084-ADJ (excluding protection circuitry) is shown in Figure 11. The
topology is basically that of the LM317 except for the pass transistor. Instead of a Darlington NPN with its two
diode voltage drop, the LM1084 uses a single NPN. This results in a lower dropout voltage. The structure of the
pass transistor is also known as a quasi LDO. The advantage of a quasi LDO over a PNP LDO is its inherently
lower quiescent current. The LM1084 is ensured to provide a minimum dropout voltage of 1.5-V over
temperature, at full load.
Figure 11. Basic Functional Diagram for the LM1084, Excluding Protection Circuitry
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Ripple Rejection
Ripple rejection is a function of the open loop gain within the feed-back loop (refer to Figure 11 and Figure 14).
The LM1084 exhibits 75dB of ripple rejection (typ.). When adjusted for voltages higher than VREF, the ripple
rejection decreases as a function of adjustment gain: (1+R1/R2) or VO/VREF. Therefore a 5-V adjustment
decreases ripple rejection by a factor of four (12dB); Output ripple increases as adjustment voltage increases.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Feature Description (continued)
However, the adjustable version allows this degradation of ripple rejection to be compensated. The adjust
terminal can be bypassed to ground with a capacitor (CADJ). The impedance of the CADJ should be equal to or
less than R1 at the desired ripple frequency. This bypass capacitor prevents ripple from being amplified as the
output voltage is increased.
1/(2π× fRIPPLE*CADJ)R1(1)
7.3.2 Load Regulation
The LM1084 regulates the voltage that appears between its output and ground pins, or between its output and
adjust pins. In some cases, line resistances can introduce errors to the voltage across the load. To obtain the
best load regulation, a few precautions are needed.
Figure 12 shows a typical application using a fixed output regulator. Rt1 and Rt2 are the line resistances. VLOAD
is less than the VOUT by the sum of the voltage drops along the line resistances. In this case, the load regulation
seen at the RLOAD would be degraded from the data sheet specification. To improve this, the load should be tied
directly to the output pin on the positive side and directly tied to the ground pin on the negative side.
Figure 12. Typical Application Using Fixed Output Regulator
When the adjustable regulator is used (Figure 13), the best performance is obtained with the positive side of the
resistor R1 tied directly to the output pin of the regulator rather than near the load. This eliminates line drops
from appearing effectively in series with the reference and degrading regulation. For example, a 5-V regulator
with 0.05resistance between the regulator and load will have a load regulation due to line resistance of 0.05
× IL. If R1 (= 125) is connected near the load the effective line resistance will be 0.05(1 + R2/R1) or in this
case, it is 4 times worse. In addition, the ground side of the resistor R2 can be returned near the ground of the
load to provide remote ground sensing and improve load regulation.
Figure 13. Best Load Regulation Using Adjustable Output Regulator
10 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
Feature Description (continued)
7.3.3 Overload Recovery
Overload recovery refers to regulator's ability to recover from a short circuited output. A key factor in the recovery
process is the current limiting used to protect the output from drawing too much power. The current limiting circuit
reduces the output current as the input to output differential increases. Refer to short circuit curve in the Typical
Characteristics section.
During normal start-up, the input to output differential is small because the output follows the input. But, if the
output is shorted, then the recovery involves a large input to output differential. Sometimes during this condition
the current limiting circuit is slow in recovering. If the limited current is too low to develop a voltage at the output,
the voltage will stabilize at a lower level. Under these conditions it may be necessary to recycle the power of the
regulator in order to get the smaller differential voltage and thus adequate start up conditions. Refer to Typical
Characteristics section for the short circuit current vs. input differential voltage.
7.4 Device Functional Modes
7.4.1 Output Voltage
The LM1084 adjustable version develops a 1.25-V reference voltage, (VREF), between the output and the adjust
pin. As shown in Figure 14, this voltage is applied across resistor R1 to generate a constant current I1. This
constant current then flows through R2. The resulting voltage drop across R2 adds to the reference voltage to
sets the desired output voltage.
The current IADJ from the adjustment terminal introduces an output error. But because it is small (120 uA max), it
becomes negligible when R1 is in the 100 range.
For fixed voltage devices, R1 and R2 are integrated inside the devices.
Figure 14. Basic Adjustable Regulator
7.4.2 Stability Consideration
Stability consideration primarily concerns the phase response of the feedback loop. In order for stable operation,
the loop must maintain negative feedback. The LM1084 requires a certain amount series resistance with
capacitive loads. This series resistance introduces a zero within the loop to increase phase margin and thus
increase stability. The equivalent series resistance (ESR) of solid tantalum or aluminum electrolytic capacitors is
used to provide the appropriate zero (approximately 500 kHz).
Aluminum electrolytics are less expensive than tantalums, but their ESR varies exponentially at cold
temperatures; therefore requiring close examination when choosing the desired transient response over
temperature. Tantalums are a convenient choice because their ESR varies less than 2:1 over temperature.
The recommended load/decoupling capacitance is a 10-uF tantalum or a 50-uF aluminum. These values will
assure stability for the majority of applications.
The adjustable versions allow an additional capacitor to be used at the ADJ pin to increase ripple rejection. If this
is done the output capacitor should be increased to 22 uF for tantalum or to 150 uF for aluminum.
Capacitors other than tantalum or aluminum can be used at the adjust pin and the input pin. A 10-uF capacitor is
a reasonable value at the input. See Ripple Rejection section regarding the value for the adjust pin capacitor.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Device Functional Modes (continued)
It is desirable to have large output capacitance for applications that entail large changes in load current
(microprocessors for example). The higher the capacitance, the larger the available charge per demand. It is also
desirable to provide low ESR to reduce the change in output voltage:
ΔV = ΔI x ESR (2)
It is common practice to use several tantalum and ceramic capacitors in parallel to reduce this change in the
output voltage by reducing the overall ESR.
Output capacitance can be increased indefinitely to improve transient response and stability.
7.4.3 Protection Diodes
Under normal operation, the LM1084 regulator does not need any protection diode. With the adjustable device,
the internal resistance between the adjustment and output terminals limits the current. No diode is needed to
divert the current around the regulator even with a capacitor on the adjustment pin. The adjust pin can take a
transient signal of ±25 V with respect to the output voltage without damaging the device.
When an output capacitor is connected to a regulator and the input is shorted, the output capacitor will discharge
into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage
of the regulator, and rate of decrease of VIN. In the LM1084 regulator, the internal diode between the output and
input pins can withstand microsecond surge currents of 10A to 20A. With an extremely large output capacitor (
1000 µf), and with input instantaneously shorted to ground, the regulator could be damaged. In this case, an
external diode is recommended between the output and input pins to protect the regulator, shown in Figure 15.
Figure 15. Regulator with Protection Diode
12 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM1084 is versatile in its applications, including uses in programmable output regulation and local on-card
regulation. Or, by connecting a fixed resistor between the ADJUST and OUTPUT terminals, the LM1084 can
function as a precision current regulator. An optional output capacitor can be added to improve transient
response. The ADJUST terminal can be bypassed to achieve very high ripple-rejection ratios, which are difficult
to achieve with standard three-terminal regulators. Please note, in the following applications, if ADJ is mentioned,
it makes use of the adjustable version of the part, however, if GND is mentioned, it is the fixed voltage version of
the part.
8.2 Typical Applications
8.2.1 1.2-V to 15-V Adjustable Regulator
This part can be used as a simple low drop out regulator to enable a variety of output voltages needed for
demanding applications. By using an adjustable R2 resistor a variety of output voltages can be made possible as
shown in Figure 16 based on the LM1084-ADJ.
Figure 16. 1.2-V to 15-V Adjustable Regulator
8.2.1.1 Design Requirements
The device component count is very minimal, employing two resistors as part of a voltage divider circuit and an
output capacitor for load regulation.
8.2.1.2 Detailed Design Procedure
The voltage divider for this part is set based on the equation shown in Figure 16, where R1 is the upper feedback
resistor and R2 is the lower feedback resistor.
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Typical Applications (continued)
8.2.1.3 Application Curve
8.2.2 Adjustable at 5 V
The application shown in Figure 17 outlines a simple 5 V output application made possible by the LM1084-ADJ.
This application can provide 5 A at high efficiencies and very low drop-out.
Figure 17. Adjustable @ 5 V
14 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
Typical Applications (continued)
8.2.3 5-V Regulator With Shutdown
A variation of the 5 V output regulator application with shutdown control is shown in Figure 18 based on the
LM1084-ADJ. It uses a simple NPN transistor on the ADJ pin to block or sink the current on the ADJ pin. If the
TTL logic is pulled high, the NPN transistor is activated and the part is disabled, outputting approximately 1.25 V.
If the TTL logic is pulled low, the NPN transistor is unbiased and the regulator functions normally.
Figure 18. 5-V Regulator with Shutdown
8.2.4 Battery Charger
The LM1084-ADJ can be used as a battery charger to regulate the charging current required by the battery bank
as shown in Figure 19. In this application the LM1084 acts as a constant voltage, constant current part by
sensing the voltage potential across the battery and compensating it to the current voltage. To maintain this
voltage, the regulator delivers the maximum charging current required to charge the battery. As the battery
approaches the fully charged state, the potential drop across the sense resistor, RS,reduces and the regulator
throttles back the current to maintain the float voltage of the battery.
Figure 19. Battery Charger
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Typical Applications (continued)
8.2.5 Adjustable Fixed Regulator
A simple adjustable, fixed range output regulator can be made possible by placing a variable resistor on the
ground of the device as shown in Figure 20 based on the fixed output voltage LM1084-5.0. The GND pin has a
small quiescent current of 5 mA typical. Increasing the resistance on the GND pin increases the voltage potential
across the resistor. This potential is then mirrored on to the output to increase the total output voltage by the
potential drop across the GND resistor.
Figure 20. Adjustable Fixed Regulator
8.2.6 Regulator with Reference
A fixed output voltage version of the LM1084-5.0 can be employed to provide an output rail and a reference rail
at the same time as shown in Figure 21. This simple application makes use of a reference diode, the LM136-5,
to regulate the GND voltage to a fixed 5 V based on the quiescent current generated by the GND pin. This
voltage is then added onto the output to generate a total of 10 V out.
Figure 21. Regulator with Reference
16 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
Typical Applications (continued)
8.2.7 High Current Lamp Driver Protection
A simple constant current source with protection can be designed by controlling the impedance between the
lamp and ground. The LM1084-ADJ shown in Figure 22 makes use of an external TTL or CMOS input to drive
the NPN transistor. This pulls the output of the regulator to a few tenths of a volt and puts the part into current
limit. Releasing the logic will reduce the current flow across the lamp into the normal operating current thereby
protecting the lamp during startup.
Figure 22. High Current Lamp Driver Protection
8.2.8 Battery Backup Regulated Supply
A regulated battery backup supply can be generated by using two fixed output voltage versions of the part as
shown in Figure 23. The top regulator supplies the Line voltage during normal operation, however when the input
is not available, the second regulator derives power from the battery backup and regulates it to 5 V based on the
LM1084-5.0. The diodes prevent the rails from back feeding into the supply and batteries.
Figure 23. Battery Backup Regulated Supply
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
Typical Applications (continued)
8.2.9 Ripple Rejection Enhancement
A very simple ripple rejection circuit is shown in Figure 24 using the LM1084-ADJ. The capacitor C1 smooths out
the ripple on the output by cleaning up the feedback path and preventing excess noise from feeding back into the
regulator. Please remember XC1 should be approximately equal to R1 at the ripple frequency.
Figure 24. Ripple Rejection Enhancement
8.2.10 Automatic Light Control
A common street light control or automatic light control circuit is designed in Figure 25 based on the LM1084-
ADJ. The photo transistor conducts in the presence of light and grounds the ADJ pin preventing the lamp from
turning on. However, in the absence of light, the LM1084 regulates the voltage to 1.25V between OUT and ADJ,
ensuring the lamp remains on.
Figure 25. Automatic Light Control
18 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
Typical Applications (continued)
8.2.11 Generating Negative Supply Voltage
A quick inverting output rail or negative output rail is shown in Figure 26 using the LM1084 fixed output part. By
tying the output to GND, the GND node is at a relatively more negative potential than the output. This is then
interfaced to the negative application such as an operational amplifier or any other rail needing negative voltage.
Figure 26. Generating Negative Supply Voltage
8.2.12 Remote Sensing
Remote sensing is a method of compensating the output voltage to a very precise degree by sensing the output
and feeding it back through the feedback. The circuit implementing this is shown in Figure 27 using the LM1084-
ADJ. The output of the regulator is fed into a voltage follower to avoid any loading effects and the output of the
op-amp is injected into the top of the feedback resistor network. This has the effect of modulating the voltage to a
precise degree without additional loading on the output.
Figure 27. Remote Sensing
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
9 Power Supply Recommendations
The linear regulator input supply should be well regulated and kept at a voltage level such that the maximum
input to output voltage differential allowed by the device is not exceeded. The minimum dropout voltage (VIN
VOUT) should be met with extra headroom when possible in order to keep the output well regulated. A 10 μF or
higher capacitor should be placed at the input to bypass noise.
10 Layout
10.1 Layout Guidelines
For the best overall performance, some layout guidelines should be followed. Place all circuit components on the
same side of the circuit board and as near as practical to the respective linear regulator pins. Traces should be
kept short and wide to reduce the amount of parasitic elements into the system. The actual width and thickness
of traces will depend on the current carrying capability and heat dissipation required by the end system. An array
of plated vias can be placed on the pad area underneath the TAB to conduct heat to any inner plane areas or to
a bottom-side copper plane.
10.2 Layout Example
Figure 28. Layout Example
10.3 Thermal Considerations
ICs heats up when in operation, and power consumption is one factor in how hot it gets. The other factor is how
well the heat is dissipated. Heat dissipation is predictable by knowing the thermal resistance between the IC and
ambient (θJA). Thermal resistance has units of temperature per power (C/W). The higher the thermal resistance,
the hotter the IC.
The LM1084 specifies the thermal resistance for each package as junction to case (θJC). In order to get the total
resistance to ambient (θJA), two other thermal resistance must be added, one for case to heat-sink (θCH) and one
for heatsink to ambient (θHA). The junction temperature can be predicted as follows:
TJ= TA+ PD(θJC +θCH +θHA)=TA+ PDθJA (3)
TJis junction temperature, TAis ambient temperature, and PDis the power consumption of the device. Device
power consumption is calculated as follows:
20 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
LM1084
www.ti.com
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
Thermal Considerations (continued)
IIN = IL+ IG(4)
PD= (VINVOUT) IL+ VINIG(5)
Figure 29 shows the voltages and currents which are present in the circuit.
Figure 29. Power Dissipation Diagram
Once the devices power is determined, the maximum allowable (θJA (max)) is calculated as:
θJA (max) = TR(max)/PD= TJ(max) TA(max)/PD(6)
The LM1084 has different temperature specifications for two different sections of the IC: the control section and
the output section. The Thermal Information table shows the junction to case thermal resistances for each of
these sections, while the maximum junction temperatures (TJ(max)) for each section is listed in the Absolute
Maximum Ratings section of the datasheet. TJ(max) is 125°C for the control section, while TJ(max) is 150°C for the
output section.
θJA (max) should be calculated separately for each section as follows:
θJA (max, CONTROL SECTION) = (125°C - TA(max))/PD(7)
θJA (max, OUTPUT SECTION) = (150°C - TA(max))/PD(8)
The required heat sink is determined by calculating its required thermal resistance (θHA (max)).
θHA (max) =θJA (max) (θJC +θCH) (9)
(θHA (max)) should also be calculated twice as follows:
(θHA (max)) = θJA (max, CONTROL SECTION) - (θJC (CONTROL SECTION) + θCH) (10)
(θHA (max)) = θJA(max, OUTPUT SECTION) - (θJC (OUTPUT SECTION) + θCH) (11)
If thermal compound is used, θCH can be estimated at 0.2 C/W. If the case is soldered to the heat sink, then a
θCH can be estimated as 0 C/W.
After, θHA (max) is calculated for each section, choose the lower of the two θHA (max) values to determine the
appropriate heat sink.
If PC board copper is going to be used as a heat sink, then Figure 30 can be used to determine the appropriate
area (size) of copper foil required.
Figure 30. Heat Sink Thermal Resistance vs Area
Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM1084
LM1084
SNVS037G SEPTEMBER 1999REVISED JANUARY 2015
www.ti.com
11 Device and Documentation Support
11.1 Trademarks
All trademarks are the property of their respective owners.
11.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.3 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
22 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated
Product Folder Links: LM1084
PACKAGE OPTION ADDENDUM
www.ti.com 8-Sep-2014
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM1084IS-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 3 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-3.3
LM1084IS-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 3 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-5.0
LM1084IS-ADJ NRND DDPAK/
TO-263 KTT 3 45 TBD Call TI Call TI -40 to 125 LM1084
IS-ADJ
LM1084IS-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 3 45 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-ADJ
LM1084ISX-3.3/NOPB ACTIVE DDPAK/
TO-263 KTT 3 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-3.3
LM1084ISX-5.0/NOPB ACTIVE DDPAK/
TO-263 KTT 3 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-5.0
LM1084ISX-ADJ/NOPB ACTIVE DDPAK/
TO-263 KTT 3 500 Pb-Free (RoHS
Exempt) CU SN Level-3-245C-168 HR -40 to 125 LM1084
IS-ADJ
LM1084IT-3.3/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM1084
IT-3.3
LM1084IT-5.0/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM1084
IT-5.0
LM1084IT-ADJ/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS
& no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LM1084
IT-ADJ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
PACKAGE OPTION ADDENDUM
www.ti.com 8-Sep-2014
Addendum-Page 2
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM1084ISX-3.3/NOPB DDPAK/
TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM1084ISX-5.0/NOPB DDPAK/
TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
LM1084ISX-ADJ/NOPB DDPAK/
TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Sep-2014
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM1084ISX-3.3/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0
LM1084ISX-5.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0
LM1084ISX-ADJ/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0
PACKAGE MATERIALS INFORMATION
www.ti.com 8-Sep-2014
Pack Materials-Page 2
MECHANICAL DATA
NDE0003B
www.ti.com
MECHANICAL DATA
KTT0003B
www.ti.com
BOTTOM SIDE OF PACKAGE
TS3B (Rev F)
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM1084IS-3.3 LM1084IS-3.3/NOPB LM1084IS-5.0 LM1084IS-5.0/NOPB LM1084IS-ADJ LM1084IS-ADJ/NOPB
LM1084ISX-3.3 LM1084ISX-3.3/NOPB LM1084ISX-5.0 LM1084ISX-5.0/NOPB LM1084ISX-ADJ LM1084ISX-
ADJ/NOPB LM1084IT-3.3 LM1084IT-3.3/NOPB LM1084IT-5.0 LM1084IT-5.0/NOPB LM1084IT-ADJ LM1084IT-
ADJ/NOPB